Why Won’t My Water Heater Light?
Your hot water heater settings are most likely remain at the factory default temperature of 140 degrees if you haven’t changed them in a long while. The latter is especially true if your hot water heater was only recently installed; the old one was almost certainly altered at some time over the years, whereas the new one is set to the manufacturer’s recommended temperature.
Thermocouple
If the pilot light does not relight after being lit, or if it goes out immediately after being lit, the most likely culprit is a faulty thermocouple. When it comes to gas-powered heating appliances, thermocouples are a critical component. The pilot light on a water heater may go out at any time, allowing gas to be spilled into the surroundings around the water heater, posing a serious explosion and health concern. An appliance’s fail-safe circuit, which detects whether or not the pilot light is still burning, helps to avoid this from happening in the first place.
When the pilot light goes out, the temperature of the thermocouple drops, which causes the voltage across the thermocouple to drop, resulting in the valve closing.
Pilot Tube
Alternatively, if the thermocouple is in good working order, a filthy pilot tube may be the source of the heater’s inability to ignite. It is possible for dirt, oil, and carbon to accumulate in the burner system and pilot light, preventing the appropriate passage of gas to these components. Fortunately, resolving this issue is a really simple and quick procedure. Cleaning out the tube with a needle or other thin and robust piece of metal should be done after shutting off the gas and allowing a few minutes for the pilot to cool is recommended.
After a thorough cleaning, re-energize the system and check to see whether the pilot will ignite.
Flex Tubing
Flex tubing can also be a contributing factor to the pilot light failing to stay lit for an extended period of time. This tube is used to connect the gas controller to the gas tank. It will guarantee that gas is delivered to the burner systems and pilot light on a consistent basis. Occasionally, this tube will get twisted, damaged, or deteriorated, which will prohibit appropriate gas flow from being achieved. If the tubing has gotten twisted, straightening the tube should be sufficient to repair the problem.
It is possible that you may want the assistance of a plumber to install new flex tubing for your gas water heater.
Main Control Valve
A malfunction with the primary control valve, which occurs only in rare situations, might result in the loss of the pilot light. Gas main control valves are typically one of the last components to break on a water heater since they are so delicate. When a primary control valve is found to be malfunctioning, it will be necessary to replace it in order to resolve the issue. Troubleshooting these fundamental causes of a water heater that won’t light will assist you in restoring your hot water supply and restoring comfort to your home.
If none of these measures are successful, or if you want more assistance in diagnosing and resolving your water heater problems, contact the experienced plumbers at Magnificent Plumbing for expert guidance.
Why Your Water Heater’s Pilot Light Keeps Going Out & How to Fix It
The date is May 13, 2021. When the pilot light flame on your gas water heater goes out, it is an annoying and frustrating situation to have to deal with. When your water heater’s pilot light fails to stay lit, you’re left without hot water, which makes even the most basic of tasks such as taking a shower a chore. Naturally, you question, “How did this happen? What happened?” Is there anything you can recommend to help you get things going again? What should I do to have it repaired? “May you tell me about the costs I can expect?” Fortunately, if your water heater pilot light goes out, you should be aware that this is a frequent problem that many homeowners have and that the time and effort required to repair it is low.
Why does the pilot light on my water heater keep going out?
Because of problems with the heater’s thermocouple or owing to access to combustible air, your water heater’s pilot light continues going out repeatedly.
Thermocouple Issues
When your pilot light is on, your thermocouple detects the presence of the flame. The thermocouple’s tip is positioned above the pilot flame, providing a voltage that maintains the gas valve open in the process. A thermocouple will shut down the gas supply to your water heater if it detects that the pilot light on your water heater is not lighting up properly. When thermocouples are exposed to moisture or dust for an extended period of time, they might malfunction, gather dust, or get bent away from the pilot light’s flame.
Lack of Combustible Air
Another reason why your gas water heaterpilot light won’t remain lighted might be that there isn’t enough combustible air in the room where it is located. To keep the pilot light on in your water heater, you’ll need to blow air into it. Otherwise, the flame will be extinguished. Take precautionary measures to ensure that the water heater is not surrounded by material, such as litter or lint, which might increase the quantity of combustible air present. Maintain as much cleanliness as possible in the surrounding region.
What do I do if my water heater pilot light keeps going out?
The lack of sufficient combustible air in your gas water heater might be another reason for the pilot light on your gas water heater not to stay lit permanently. To keep the pilot light on in your water heater, you’ll need to blow on it. The flame will be extinguished if this happens. Make certain that the water heater is not surrounded by clutter, lint, or debris, since this will increase the quantity of combustible air in the vicinity. Maintain as much cleanliness as possible in the immediate vicinity.
- Locate the gas shut-off knob and turn it all the way to the “Off” position. The gas flow is halted as a result of this. Allow for a few minutes for the gas to dissipate before continuing. To get access to the burner, remove the access panel. To begin the flow of gas, turn the knob to the “Pilot” position. You’ll want to press and hold the knob down for a few seconds. While still holding the gas knob, ignite the pilot with a long lighter while still holding the gas knob. To ignite your gas water heater, use the button on the side of the tank that says “ignite.” As soon as the flames have been extinguished, turn the gas knob to the “On” position and wait for the main burner to come on.
If you are unable to relight the pilot or if your pilot light keeps going out, it is possible that you have another problem, such as a faulty thermocouple, to consider.
Please refer to the owner’s handbook for your water heater equipment for further information.
Can I replace a thermocouple myself?
It’s possible that you have a defective thermocouple if you can’t relight the pilot or if your pilot light continues going out despite your efforts. Note: Consult the owner’s handbook for your water heater device.
Call BGE HOME
Please contact BGE HOME at (410) 918-5600 if your water heater pilot light will not light or continues going out. You may also contact us online. Our licensed specialists are available 24 hours a day, seven days a week to come out and inspect your water heater and make recommendations on how to get it running safely and effectively again. This item was posted on Thursday, May 13th, 2021 at 4:09 pm and is filed under Uncategorized. Commenting and pinging are temporarily closed for this post.
Help, My Pilot Light Won’t Light or Stay Lit! Do THIS.
Let’s begin by discussing what the water heater pilot light is and how it works so that you may better grasp how it works. An electric pilot light is a tiny flame that is provided in order to start the gas burner on a water heater. The color of a functioning pilot light should be blue, which can assist you in determining whether or not your pilot light is functioning properly.
My Pilot Light Won’t Light on Water Heater, What Now?
In order for you to better grasp how a water heater works, let’s start by discussing the pilot light. Typically, a pilot light will be present to start the gas burner in your water heater. The color of a functioning pilot light should be blue, which can assist you in determining whether or not your pilot light is functioning correctly.
Water Heater Pilot Light Keeps Going Out?
Remember to read and follow the instructions on the water heater’s label! It’s probable that you have a problem with the hot water heater thermocouple if your pilotlight doesn’t re-light, won’t remain lighted, or continues going out after a short period of time. This is something that can happen as you become older. More information on the life expectancy of water heaters can be found in this page titled how long do water heaters last? Let’s have a look at how to identify whether a thermocouple is faulty in the section below.
How to Determine If You Have Gas Hot Water Heater Thermocouple Issues
At the heart of your water heater is a thermocouple, which detects heat emanating from the pilot light and regulates the flow of gas to the burner. When a thermocouple fails, gas will be cut off to both the pilot and the burner, which is when people realize that the water heater pilot light has gone out in the first place. The pilot light on your water heater works in conjunction with the rest of the unit. When your thermocouple senses that the pilot light on your water heater is not lit, it immediately turns off the gas to your water heater as a safety measure.
You will need to replace the gadget or have it repaired in order to resolve the problem.
How to Replace Thermocouple on Water Heater?
Water heater repairs are something that HVAC firms are occasionally called upon to do. While some people are capable of doing this procedure, it is recommended that you get a certified plumber to assist you. If you live in the area, we are a plumber in Arlington TX that can replace the thermocouple in your hot water heater on a regular basis.
However, there is some good news. Most thermocouples may be replaced at a low cost and in a short period of time, sometimes in less than an hour, by a capable homeowner with some basic tools.
Determining the Thermocouple Issue If It’s Not Broken
Your thermocouple, on the other hand, may not necessarily be faulty. If it’s contaminated, the electric current from the pilot may be disturbed, resulting in a gas leak from the pilot. This is a simple problem to solve. The following are the steps to cleaning your thermocouple: Locate the thermocouple and clean it with a piece of sandpaper once it has been cleaned. Always remember to turn off the gas before you begin cleaning, and to make sure that your thermocouple is completely cold before you begin cleaning.
When it is bent to a certain degree away from the pilot light, it ceases to work since it will no longer be able to detect heat.
Make certain that you
WhenNotto Replace Your Thermocouple
In the case of a gas water heater with a closed burner chamber or one that does not have a pilot light, entry will be far more difficult. In order to replace this sort of thermocouple, you will almost certainly require the assistance of a specialist.
Water Heater Pilot Light Won’t Stay Lit?
If you have followed these instructions and your water heater pilot light still won’t remain lit, you may require expert assistance to resolve the issue. If you reside in Arlington TX, give All Mastersa a call, and we can resolve any of your hot water heater thermocouple or pilot light problems. In the Arlington and broader DFW region, you may ask about troubleshooting why your pilot light isn’t working correctly over the phone using our new video chat application. Call (817) 200-4703 for more information.
8 Reasons Why Your Water Heater Pilot Light Won’t Stay Lit
For those of you who aren’t technicians, I can imagine that there’s nothing more frustrating than trying to keep a pilot light lit when it won’t remain lit for whatever reason at that moment. Along with interfering with the proper operation of the furnace, it can also hinder you from enjoying the luxury of a hot morning shower. There are a variety of reasons why your pilot light keeps flickering on and off repeatedly. We’ll do our best to cover all of the probable explanations for your heater’s current state of malfunction.
Following a discussion of the underlying reasons, we will offer some suggestions for potential remedies that you may utilize to resolve the issue.
Why Does Your Heater’s Pilot Light Keep Going Off?
The following are the most typical reasons why the pilot light on your heater won’t remain lit:
1. Obstructed Thermocouple
The thermocouple is used in the operation of the majority of newly developed water heaters. This component is the primary cause for the operation of your water heater; it also determines whether the pilot light is on or off by drawing electricity from the heat generated by the pilot. When the thermocouple senses that the pilot light is not lit, it automatically shuts off the gas as a safety precaution. It is also possible that an unlit pilot is caused by a dirty thermocouple, since the dirt may be obscuring the current signal, which would result in a gas leak.
To clean your thermocouple, first make sure that the gas valve is turned off. You don’t want to take the chance of causing a leak when cleaning your thermocouple. The thermocouple may be found and cleaned with relative ease.
2. Bent Thermocouple
The thermocouple can get curved or bent to the point that it begins to lose the heat signal generated by the electrical current, in addition to being dusty and grimy and becoming bent. The thermocouple may have bent too far away from the pilot in the majority of cases, which is problematic since it will not be able to detect the heat signal. Make sure your thermocouple is straight: Normally, the flame is meant to come into contact with the thermocouple just enough for it to detect heat. It is possible to correct a bent thermocouple by bending it back towards the pilot, if you discover that it is bent.
3. Damaged Thermocouple
Another cause for your pilot not to be lit might be due to a faulty thermocouple in the ignition system. If you inspect the thermocouple and find it to be clean, filthy, or curved, it is possible that it has been damaged. Removing the thermocouple and testing it with a multimeter will help to confirm your assumptions. Before removing the thermocouple, make sure that the gas is switched off and that the thermocouple is completely cold before doing so. If the voltage it produces is less than 20 MV, it is considered damaged.
When a thermocouple is just slightly damaged, it is possible to repair it.
4. Dirty Pilot Tube
Having a faulty thermocouple is another reason why your pilot can be out of commission. if you inspect the thermocouple and find it to be clean, grubby, and not curved, it is possible that the thermocouple has been compromised. Remove the thermocouple and do a multimeter test on it to validate your concerns. Prior to removing the thermocouple, be certain that the gas has been turned off and that the thermocouple is completely cold. This device is destroyed if the voltage it delivers is less than 20 MV.
If a thermocouple is just slightly damaged, it may be fixed.
5. Flex Tube Defects
This is another another possible explanation for why your pilot’s light is not working. The flex tube is responsible for delivering gas to the device, and if the continuous flow of gas is disrupted, the pilot light will fail to illuminate. When the tube is kinked at one or more spots, this is the most common occurrence. Check the flex tube for damage: Check the tube along its length to ensure that it is straight and there is no restriction to the passage of gas.
However, if this does not resolve the issue, you may be forced to replace the tube totally, which would be costly. Before you resort to changing the tubes, be certain that you’ve checked all of the other possibilities first, because flex tube problems are less common in general.
6. Main Control Valve
A defective main control might be the source of the pilot light’s inability to remain lit. This is still another issue that happens less frequently, so you must rule out all other possibilities before concluding that the error is due to the primary control system. If you’re not sure about something, check the controls with your multimeter. To replace the control valve, follow these steps: Control valves are frequently repaired by technicians, even if the valve itself is not malfunctioning. However, if you want your water heater to run as long as possible and if you want to save future costs, you might think about replacing the main control valve altogether instead.
7. Faulty Electrical System
The majority of the blame for this problem may be assigned to electric water heaters. This problem is frequently caused by incorrect wiring of the internal electronics. A badly connected electrical water heater has a tendency to blow the fuse and short circuit the circuits, which are the two most common problems that an electric water heater encounters. It is common for a malfunctioning electrical system to be identified by a breaker shutdown, which results in the water heater being shut off without the user’s knowledge.
If you do not have sufficient experience, do not attempt to repair it yourself.
8. A faulty burner
Electric water heaters are mostly to blame for this problem. This problem is frequently caused by faulty wiring of the internal components on the motherboard. Electric water heaters have a tendency to blow fuses and short circuit circuits when they are improperly connected, which are two of the most common problems that they face. It is common for a malfunctioning electrical system to be identified by a breaker shutdown, which results in the water heater being shut off without the user’s knowledge or consent.
If you don’t have enough experience, don’t try to fix anything on your own!
How to Re-Ignite the Pilot Light
This problem is primarily associated with electric water heaters. This problem is frequently caused by improper wiring of the internal electronics. A badly connected electrical water heater has a tendency to blow fuses and short circuit circuits, which are the two most common problems that electric water heaters encounter. It is common for a malfunctioning electrical system to be identified by a breaker shutdown, which results in the water heater being shut off without the user’s consent. How to make it better: If you have reason to believe that there is a problem with the electrical wiring, contact an expert to inspect the wiring.
Take advantage of your warranty
Most water heaters are covered by a 1- or 2-year guarantee in the majority of instances.
If your pilot light malfunctions during this time period, you may always return to the store where you purchased it and get it repaired there. This is quite advantageous since, in the majority of situations, they will be able to fix any broken equipment or even completely replace the water heater.
Hire a technician
Depending on whether your water heater has outlived its warranty time and if you’ve carried out all of the recommended maintenance and adjustments, this may be your only option. While most homeowners would consider this a last choice, it is important to remember that the majority of individuals are not DIY enthusiasts. Additionally, dealing with gas and electricity is quite delicate, which is why you should exercise extreme caution. Hiring a professional may result in more charges, but it may also result in you being safer, which should be your number one priority.
A technician also has the ability to predict potential problems in the future and to provide advise or solutions to help avoid them.
Final thoughts
It is possible for a variety of things to go wrong and for your pilot light to fail to stay illuminated. The thermocouple, pilot tube, flex tube, and main control valve, on the other hand, are the traditional suspects in this case. The advice in this blog should assist you in resolving these challenges, or at the very least in determining the root cause of the problem. If nothing seems to work, you should seek the services of a qualified specialist to repair the pilot light. Have you ever had to deal with a pilot who was unable to light his or her engine?
5 Reasons Why Your Water Heater Pilot Light Won’t Stay Lit (and How to Fix)
Please keep in mind that this content may contain affiliate links. This means that, at no additional cost to you, we may gain a small profit on purchases made via our links. Below is a list of the top five reasons your pilot won’t stay on the flight, as well as solutions for each problem. Important Important: Before performing any of these diagnostics or repairs, switch off the gas and wait at least five minutes for the gas pressure and fumes to dissipate before starting the engine. Generally speaking, this is a decent rule of thumb for relighting the pilot in general, and not simply for diagnostic purposes.
Reason 1: Dirty Pilot Tube
Dirt and debris can accumulate in the pilot tube, preventing the flow of gas from flowing properly. As a result, the pilot does not receive enough fuel to keep the engine running. If the pilot will not ignite at all, this is also a plausible explanation. Fortunately, a clogged pilot tube is the most straightforward problem to resolve.
How to Fix
All that is required is a needle to be inserted into the pilot hole and carefully removed from the hole. If there is a significant amount of material in the tube, it may take many attempts to finish the procedure. Checking to determine if this step was successful is as simple as igniting the pilot and observing whether or not it lights up properly and remains lighted. A flame that is in good health will be blue in hue.
Reason 2: Kink in the Flex Tube
Simply insert a needle into the pilot hole and carefully remove any debris with the needle. Depending on how much material is in the tube, it may take a few of tries to get everything out.
If this stage was successful, it is as easy as lighting the pilot and observing if it illuminates properly and remains lighted throughout the procedure. A blue flame indicates that it is in good condition.
How to Fix
Perhaps the simplest problem to resolve, you only need to search for any kinks in the tube and unkink them, as seen in the picture. If the problem persists, it is possible that you are experiencing a problem with the thermocouple.
Reason 3: Obstruction in the Thermocouple
If you have a kink in the tube, you just need to unkink it, which is perhaps the simplest issue to resolve. If the problem persists, it is possible that the thermocouple is the source of the problem.
How to Fix
Perhaps the simplest problem to resolve, you only need to search for any kinks in the tube and unkink them. If the problem persists, it’s possible that you’re dealing with a problem with the thermocouple.
Reason 4: Damaged Thermocouple
This is a more serious issue, since it may necessitate the replacement of the component. Damage may manifest itself in the form of the sensor being bent too far away from the pilot light, or it may indicate that the entire unit is no longer operable.
How to Fix
This is a more serious circumstance in which the part may need to be replaced. Damage may manifest itself in the form of the sensor being bent too far away from the pilot light, or it may indicate that the entire device is no longer operational.
Reason 5: Main Control Valve
This is the problem that you want to avoid at all costs among the ones that you can diagnose on your own. The quickest and most straightforward method of diagnosing a faulty control valve is to exhaust all other possibilities first. Given that all other possibilities have been checked out and that the thermocouple is displaying data on the multimeter, this is probably definitely the cause of the problem.
How to Fix
Control valves that have failed can only be repaired or replaced if they are completely destroyed. This can be more expensive than other do-it-yourself difficulties, and it can be more challenging for individuals who are not familiar with this type of job.
When All Else Fails
Control valves that have failed can only be repaired or replaced if they are defective. For people who are unfamiliar with this type of labor, it may be more expensive than other Do it yourself difficulties and more complex.
Top 10 Gas Water Heater Pilot Light Problems! When It Won’t Stay Lit!
It is explained in this article how the thermocouple, the gas valve solenoid, and the pilot flame function on a water heater. I will go through ten different problems that can arise and cause the pilot flame to go out, as well as the solutions for each of these difficulties. The following instructions demonstrate how to ignite the pilot light on a water heater and describe the critical components of the water heater that enable it to function properly. The process of lighting a pilot should be rather straightforward.
The temperature dial is located on the front of the gas valve.
When the sparker button is pressed, a wire is linked to the pilot assembly, and this is known as the pilot assembly wire.
Set the front dial to “pilot lighting” or “night vision” mode.
Why Your Pilot Light Keeps Going Out & How To Fix [With Pictures]
That darn pilot light just won’t stay turned on! Moreover, it is causing all of your plans for today to be derailed. Nothing compares to the sensation of taking a hot water shower. However, there are times when this does not occur. After all, there are worse things than having a very cold bath, should we say? The one thing that everyone despises is a lack of running water. This may be incredibly inconvenient – not only for showering, but also for all of the other duties that require hot water to be completed successfully.
You don’t have to put your day on wait because your pilot light isn’t working properly. Continue reading to learn what a pilot light is, why it is so important to your comfort, how to relight it, and how to replace it.
What’s A Pilot Light?
An electronic device that maintains a continually burning flame is known as a pilot light. Basically, the goal of this section is to light the burner. How? When you switch on your appliance, gas is released from the main burner, and the pilot light flame ignites the gas, so supplying heat to the room. With each degree of heat generated by the main burner, the air or water contained within your appliance is heated and then disseminated as needed around your residence or place of business
Appliances With Pilot Lights
Water heaters, older furnaces, and boilers are more likely to have a pilot light than other types of appliances. You may also discover that your gas fireplace has a pilot light, which is a good thing. Learn how to switch on the pilot light on your gas fireplace by visiting this page. Pilot lights have been gradually being phased out in favor of hot surface igniters or spark igniters in more recent years. pilot light for a water heater The pilotflame ignites the gas, which generates heat for your house or place of work.
Also, if you are experiencing no heat, check to see whether the pilot light on your furnace or boiler has gone out.
Water Heater Pilot Light: Where Is It And What Does It Do?
A little access panel, located just underneath the thermostat, may be found at the very bottom of your gas water heater. The pilot light for the gas water heater is located within the access panel. There will be a gas panel where you may check to see if the pilot flame has been ignited. The pilot light on your water heater is a little flame that is used to ignite the gas burner in the water heater. This is required for the purpose of heating the water that will be dispersed around your home. If you are experiencing no hot water and have attempted to relight your pilot light without success, you will require water heater repair.
Warning!
This photograph was shot by a water heater professional for the purpose of demonstrating pilot operation.
What Makes Your Water Heater Pilot LightGo Out
Thermocouple on the water heater is faulty. The thermocouple is responsible for detecting whether your pilot light is on. This copper rod serves as a safety precaution, preventing the heater’s gas supply from being turned off if the pilot light on the water heater goes out. The natural wear and tear of a thermocouple can cause it to get twisted out of place, to malfunction, to become broken, to become covered in dirt, or to accumulate carbon deposits. When one or more of these conditions occurs, the thermocouple will be unable to reliably detect the pilot light and will subsequently shut down the heating system.
Strong Breeze Can Blow Out Pilot Light
In some cases, such as when there is heavy wind or a nearby draft, your pilot light may be extinguished. Unless your pilot light has simply been out, you should have little trouble re-igniting it and keeping the flame burning.
Kink in the Flex Tube
The fuel is delivered to the gas controller by flexible tubes.
Gas will not flow through the tube if there is a kink or twist, which can also lead to pilot light difficulties.
Filthy Pilot Light OpeningCan MakePilot Light Keeps Going Out
If the pilot’s mouth is clogged with muck and debris, it will be virtually hard for it to maintain a flame. It will only keep a modest flame that will be readily extinguished if it does catch fire. Your pilot light will not stay lit if your pilot orifice is clogged with debris.
How Do I Re-Light My Gas Water Heater Pilot Light?
The pilot light on the water heater is not lighted.
Step 1: Thoroughly Read Gas Water Heater Manual
To have a better knowledge of where each component of your water heater is situated, consult your water heater’s instruction manual.
Step 2: Turn Down Thermostat
To have a better knowledge of where each component of your water heater is situated, consult your water heater handbook.
Step 3: Turn OFF Gas
The gas valve for the water heater Locate the gas shut-off valve and turn it all the way to the “Off” position. The gas shut off valve is positioned on the gas line near the base of your water heater, near the base of your water heater. Before proceeding on to the next stage, you must wait at least 5 minutes to guarantee that all of the gas has dissipated completely.
Step 4: After 5 Minutes, Turn The Gas Control Valve Setting On Water Heater To “Pilot”
The gas valve of a water heater. The gas shut-off valve should be located and turned “off.” Located near the base of your water heater on the gas pipe, the gas shut off valve is a safety feature. Before proceeding to the following step, you must wait at least 5 minutes to confirm that all of the gas has dissipated.
Step 5: HoldDownthe Reset Button
Keep the water heater reset button depressed. After that, press and hold the reset button. This is a button that is often red in color and is situated to the left of the gas control valve. Keep your finger on this button. To be on the safe side, use the instructions to identify each component.
Step 6: While Holding Down The Reset Button, Press TheIgniter
Keep the water heater’s igniter down. The igniter is located to the right of the gas control valve. While continuing to keep the reset button down, press the igniter button on your keyboard. Click on the water heater’s gas window until you see a blue flame appear in the glass.
Step 7: Continue To Hold Down The Reset Button For 20-30 Seconds.
Following the sighting of a flame and the removal of your finger from the igniter, you must continue to press the reset button. Continue to hold the button down for another 20-30 seconds.
Step 8: Turn The Gas Control Valve To The “On” Setting
It is necessary to maintain pressure on the reset button after you have seen a flame and removed your finger from the igniter. For a further 20-30 seconds, push and hold the button down.
Step 9: Turn The Thermostat Up
Increase the temperature of the water heater. Now is the time to dial up the heat in order to get that hot water flowing again!
Step 10: Enjoy Your Warm Water, Or Ask For Help!
If you try to relight the pilot light and it does not stay lit, you may want the services of a professional to assist you with your water heater repair.
But What If You Don’t Have A Manual Igniter?
After that, remove the access panel that is located beneath the water heater thermostat and discard it. You can use a wrench to help you.
After 5 minutes, Turn Gas Control Valve To “Pilot”
Now, set the gas shutoff valve to the “Pilot” position.
Next, Hold Gas Control Valve Down And Ignite Pilot With A Lighter
Keep the gas knob pressed down as you ignite the pilot using a long lighter, similar to a BBQ skewer. If your gas water heater, on the other hand, has an igniting button, use it instead.
Once TheFlame Is Lit,Turn Gas Control Valve to “On”
As soon as the pilot light is lighted, you may remove the reset button and turn the gas knob to the “On” position, which will take around 30 seconds.
You should be able to hear the main burner turn on at this point. Your pilot light should now be able to maintain a flame, and hot water should be flowing again!
Furnace Pilot Light: Where It Is And What Does It Do?
Old furnaces rely heavily on the pilot light to generate heat, which is why it is so crucial to keep the pilot light on. When the gas valve is opened, the flame will continue to burn constantly, igniting the gas. The heat generated by this process then heats the air that is drawn into your furnace, which is then dispersed throughout your house. If your furnace’s pilot light is out, you may notice that it is spewing chilly air into the house. The failure of the pilot light is one of several probable causes of your furnace’s inability to switch on.
You may find the pilot light by following the gas line into your furnace and looking for it there.
From there, you should be able to see a little tube that leads somewhere.
Why Furnace Pilot Light keeps going out
There are a variety of reasons why the pilot flame on your furnace continues flickering out of control. Let’s get started!
Faulty Thermocouple Triggers Pilot Light to Go Out
It is meant to shut off the gas valve if the pilot light goes out, and it is used in conjunction with a thermocouple. Thermocouples can be damaged or worn out over time. If the thermocouple is incorrectly positioned or malfunctioning, the gas valve may be incorrectly shut off, as well as preventing the pilot light from keeping lit.
Dirty Thermocouple Makes Pilot Light Keeps Going Out
A filthy thermocouple may cause the safety mechanism to mistakenly trigger, causing the ignition to be turned off. The thermocouple has the potential to accidentally shut off the gas valve and extinguish the blazing flame.
Filthy Pilot Port/Orifice
A clogged thermocouple may cause the safety device to mistakenly activate, causing the ignition to be turned off prematurely. Because of this, it is possible for the thermocouple to accidentally close the gas valve and extinguish the fire.
Bad Gas Regulator
A filthy thermocouple may cause the safety device to erroneously activate, causing the ignition to be turned off. The thermocouple has the potential to accidentally shut off the gas valve and extinguish the blazing flame.
Bad Flue Venting Could Blow Out Pilot Light
Excess wind might enter via the openings in your flue pipe if it is loose, broken, or not correctly attached to the furnace. This would extinguish the pilot light flame.
A Strong Draft
There’s always the potential that a powerful draft knocked out your pilot light’s flame and caused it to go out.
How To Re-Light A Furnace Pilot Light?
You should never rule out the chance that a strong airflow was the cause of your pilot light being extinguished.
Step 2: Identify Pilot Light
Find the location of the pilot light in your furnace by consulting the owner’s handbook. In order to get access to the furnace, you will need to remove the front of the furnace.
Step 3: Turn OFF Gas
Locate the pilot light in your furnace by consulting the owner’s handbook for assistance. In order to get access to the furnace, you will need to remove the front of the unit.
Step 4: WAIT 5 Minutes, then Turn Gas to “Pilot”
Immediately after waiting 5 minutes, switch the gas valve to the “PILOT” position.
It is vital that all of the gas has dissipated before switching the gas position to the pilot position. A few of minutes might be the difference between a peaceful society and a disasterous one. Keep in mind that gas is quite explosive!
Step 5: Hold Reset Button
After that, hold down the reset button. However, if you are having difficulty locating the reset button, your furnace’s owner’s handbook should be able to point you in the appropriate place.
Step 6: Press Igniter While Holding Reset Button
Holding the reset button down for a second or two will allow you to activate the igniter and light the flame. Once the flame has been ignited, remove the igniter and continue to hold down the reset button until the flame has been extinguished. Keep the reset button pushed for 20-30 seconds to complete the process. To light the pilot when you do not have a manual igniter, you can use a BBQ lighter or a match. furnace with a pilot light
Step 7: Turn Gas to “ON” position
Restore the pilot light by turning the gas control valve back to its “ON” position once it has been re-ignited. Right now, you should be able to keep your house warm!
Step 8: If you Aren’t comfortable yet, call a pro!
If, despite doing the necessary measures, you are still unable to keep your pilot light lit, contact an HVAC professional for furnace repair.
Boiler Pilot Light: Where It Is And What Does It Do?
The pilot light in your boiler is vital for the boiler to function properly and generate heat. It is necessary for the pilot to burn constantly in order for it to ignite the gas when the gas valve is opened. When this occurs, your boiler starts heating the water, which is subsequently dispersed throughout your house to provide warmth. If your pilot light goes out, your boiler and central heating will not be able to operate properly. The pilot light is placed within your boiler, on the other side of the valve from the gas valve.
Why Boiler Pilot Light Goes Out
A malfunctioning, misaligned, filthy, or damaged thermocouple is frequently the source of your pilot light’s failure to illuminate properly. It is the thermocouple that keeps the gas valve from opening if the pilot light is not lit. Your pilot light may not function properly if there is an issue with your thermocouple, or if it is just coated with dirt and debris.
Dirty Pilot Opening
A malfunctioning, misaligned, filthy, or damaged thermocouple is frequently the source of your pilot light’s failure to illuminate. The thermocouple is an automated safety shutdown mechanism that prevents the gas valve from opening if the pilot light is turned off or not working. Your pilot light may not function properly if there is an issue with your thermocouple, or if it is just coated with dirt and debris.
Weak Gas Regulator Can Make Pilot Light Keeps Going Out
If you have gas appliances in your home, you will have a gas regulator outside your home. The failure of your gas regulator may result in your furnace not receiving enough gas to keep its pilot light lit. In the event that you observe pilot light issues on more than one device, such as your water heater, it is possible that your gas regulator is broken or weak.
A Strong Draft
Those of you who have gas appliances will have a gas regulator outside your home.
The presence of a faulty gas regulator may prevent your furnace from receiving enough gas to keep the pilot light lit. The possibility of a broken or weak gas regulator exists if you have pilot light issues on more than one item, such as your water heater.
How To Re-Light Boiler Pilot Light
Make sure you are familiar with the components of your boiler by reading the instruction manual thoroughly. It is common for the owner’s handbook to contain instructions for re-igniting the pilot light.
Step 2: Shut OFF Boiler
Starting with shutting off the boiler is always a good idea.
Step 3. Shut OFF Gas
Locate the gas valve and turn it to the “OFF” position.
Step 4. Wait 10 Minutes
Continue to check the pipes for around 10 minutes to ensure there is no residual gas.
Step 5. Open Boiler and Locate Pilot Light
After a short period of time, you can turn on the boiler. To obtain access to the pilot light, remove the access panel from the wall. Typically, this panel is positioned next to the gas control knob box, which is where it gets its name. Sometimes you may simply lift the panel up, but other times it may be screwed to the wall or ceiling.
Step 6. Turn Gas to “Pilot”
Now, set the gas control valve to the “Pilot” position on the pilot valve.
Step 7. Hold Reset Button, Then Click Igniter
Next, press and hold the reset button for a few seconds. While still holding down the reset button, press and hold the igniter button until you see a flame appear. It is necessary to press the reset button for an additional 20-30 seconds after the flame is ignited to ensure that it is fully functional.
Step 8. Turn Gas Control Valve To “On” Setting
Restore the pilot light by turning the gas control valve back to its “ON” position once it has been re-ignited. Right now, you should be able to keep your house warm!
Step 9. Relax in Comfort
How did things turn out? If not, when will you get your home warm and comfortable? If your pilot light has been struggling to keep a flame, or if you are still unclear how to fire your pilot light, boiler repair is simply a phone call away! Now that you don’t have to struggle with a cold house anymore, you may turn to a licensed professional with your queries and concerns. To arrange a boiler repair, call or go online to this page. With the help of superTech HVAC Services, you can relight your pilot light in no time.
How Do I Prevent My Pilot Light From Going Out?
Describe your experience. So, has your house been properly heated and insulated? Whether your pilot light has been struggling to sustain a flame, or if you are still unclear how to fire your pilot light, boiler repair is just a phone call away! Rather of dealing with a cold house any longer, you may delegate your queries and worries to a licensed expert. To arrange a boiler repair, call or go online to this link. Utilize superTech HVAC Services to relight your pilot light quickly.
Soak Up The Warmth!
That’s all there is to it! A basic description of how to relight your pilot light, as well as the most typical causes for your pilot light to go out is provided. We all know that having no heat or hot water in your house is the worst feeling in the world! The best course of action if you’re having difficulties keeping your pilot light lit or are still unclear about the process is to call a professional. If you are experiencing any pilot light issues, please don’t hesitate to contact us at (443) 219-7798 or make an appointment onlinehere.