Where Should A Whole House Water Filter Be Installed

Whole House Water Filter System Installation

This page may contain affiliate links, so please keep that in mind. If you purchase a product or service after clicking on one of these links, we will get a commission at no additional cost to you. See our product review method in further detail, or read our FTC affiliate disclosure for more information. Clean water is delivered throughout your entire home via a whole-house filter system, allowing you to enjoy wonderful drinking water from every tap, chlorine-free showers, and brighter clothing.

Sounds a little frightening, doesn’t it?

It’s just somewhat tough to get everything up and running in order.

Have you come up with a concept for your next do-it-yourself project?

The information in the following article will give you with all you require.

  • Is it better to install a water softener before or after another type of water softener?
  • Installing a whole-house water filtration system: schematic, parts list, and installation instructions

Location – Where to Install a POE Filter?

What is the best location for your new whole home water filter? This is the first question that must be answered. Of course, you want to find a position that is close to where the main water line enters your home so that you have filtered water available at all of your fixtures. The sole exception is exterior faucets, which are often not required to use filtered water – but this is entirely up to you! A convenient location is also important so that you can service your filtration system – mostly replacing cartridges – without having to make a big deal out of it.

This will enhance the lifespan of your water heater as well as the lifespan of all of your household appliances that require hot water since they will no longer have to cope with sediment, lime, and other contaminants that may be present in your water supply.

What is the best POE water filtration system?

More information may be found in our reviews of the finest whole home water filters.

Before or After Water Softener?

Does it make more sense to install your new whole-house unit before or after your existing water softener (if you have one)? To protect the ion exchange media from chlorine and to rule out the possibility of pressure concerns, municipal sources should be treated before the softener. Some experts recommend backwashing after the softener for well supplies to guarantee full flow during backwashing. Furthermore, unless you chlorinate your well, your water will not contain any chlorine that would need the use of a chlorine removal system.

Is Outside Installation a Good Idea?

Although installing your entire home filter outside is not completely out of the question, keeping it in your garage or basement is the preferable alternative in most cases.

Installation Diagram

For your convenience, I’ve included a little assembly diagram that you might find useful: The following is a list of the tools, components, and installation accessories that you will require for your project:

Parts

  • With its many components, the filtration system is comprised. Not all mounting brackets are included
  • Tubing
  • (Push) fittings
  • Shut-off valves are not included. Optional bypass valves are also available. The use of pressure gauges is optional.

Required Tools

  • To complete this project, you will need the following tools: Drill, drill bits, 2x adjustable wrench, pipe cutter or hacksaw, bucket, Teflon tape, screwdriver, soldering materials (optional).

How to Install a Whole House Water Filter System

That being said, no matter which model you pick, the core method of installing a whole home water filtration system remains the same regardless of which model it is. If you are handy around the house, you should be able to complete the full setup in little more than one afternoon (2 to 4 hours). The following are some step-by-step instructions to get you started: Before you begin, thoroughly read the handbook and make certain that you are in compliance with any applicable plumbing codes in your area.

  1. Turn off the main water supply first, then drain any residual water by opening all of the faucets and fixtures in the house. Additionally, this will relieve pressure. Make a cut through the primary line. Make sure you remove a length of pipe that is large enough to fit your filtration system and all of its components. Preparing a bucket ahead of time will help to prevent spills. Sand the burrs on both ends of the pipe that has been cut
  2. Remove any debris that may have accumulated inside the pipe. One shut-off valve should be installed on either side of the system to make maintenance easier. A whole-house water filter bypass valve should also be considered for the purpose of retaining water in your home even when the system is in service mode. Close all of the valves for the time being
  3. If you want to be able to monitor the input and output pressures, add a pressure gauge next to each shutoff valve. So you’ll be able to see at a look when it’s time to adjust your filters
  4. If required, connect a piece of plywood to the rear wall of the room to make installing the system easier. It is now time to install the actual system. This will need a significant amount of dry fitting (flex piping is great for this). Double-check to see that the In and Outports are pointing in the correct directions. If your pipe size does not fit into the ports, adapters can be used. Apply Teflon tape to all threaded ends to help seal them and prevent leaks from occurring. To avoid cracking, avoid over-tightening any plastic fittings to avoid damaging them. When using push fittings, there is no need to solder any connections. You can solder the pipe ends if you prefer, but make sure the pipe ends are clean and that the heat does not reach any plastic. If your whole house filter comes with housings, thoroughly wash their interiors in hot water before installing them to remove any manufacturing debris before installing them. Make sure that the O-rings are properly greased and that they are securely fastened. Reconnect the water supply
  5. Close all of the valves save the bypass valve
  6. Look for any leaks. If necessary, tighten the fittings and the filter housings. Grounding the electrical system in older homes is frequently accomplished through the use of water pipes. This may occur in your home
  7. In this instance, a jumper cable (copper wire) should be installed from one side of the filter to the other in order to guarantee that the ground is maintained. This may be accomplished with the assistance of grounding clamps. For many minutes, flush the entire system with water. This will remove any air, old water, and installation debris that may have accumulated. Follow the manufacturer’s directions to ensure that any filtering medium is properly activated. After the pressure has been restored, turn off all of the outlets. Done

For your information, the bypass valve remains closed during normal operation. When the system requires maintenance, close both conventional valves and open the bypass valve at the same time.

Video

FYI, the bypass valve remains closed during regular operation. Close both normal valves and open the bypass valve whenever the system requires service.

Time to Get Started

We have shown that installing a whole home filter in the do-it-yourself approach is actually not that difficult. Simply double-check that you have all of the essential tools and components before you begin, and make sure to follow the manufacturer’s directions to the letter. Any time you are in question, call customer support and look for extra assistance online. It won’t take long for you to have your new whole-house filtration system installed! Interested in more do-it-yourself projects? Make your own whole-house water filter with these simple instructions.

Gene Fitzgerald’s biographical information Gene Fitzgerald has been a part of the BOS family since its inception.

Gene enjoys reading books on philosophy and social topics, producing music, and going on hikes when he is not at BOS.

Whole House Filter Installation. A simple how to guide.

Fresh, clean, delicious tasting drinking water may be given to every tap in the house when a whole house filter installation is completed properly. One of the first questions that comes to mind when thinking about a whole home water filter system installation is, “How difficult is it to install a whole house water filter system?” The installation of whole-house water filters is rather simple. When measured on a scale of one to 10, the complexity of installing a whole house water filter system is around a five.

Where to Install the Water Filter?

In order to prepare for the installation, you’ll need to pick where you want your new water filtration system to be put. A whole house water filtration system, as the name implies, ensures that all of the water in the house is filtered, with the exception of water from outside faucets. You’ll want to select a place that is close to the water main (where the main water ffeed comes into the house). Other considerations for site include a position that allows for simple maintenance access as well as a location that is upstream of your water heater.

Homes that use private wells should most likely have a backwash system built after the softener to ensure that the flow is not obstructed while backwashing the system.

Is it preferable to have the installation done outside or inside?

The installation of the system on the inside will make system maintenance easier and more realistic. The option, on the other hand, is entirely up to the individual homeowner.

Having the Proper Tools is Essential

When it comes to any undertaking, the ancient adage “A man is only as good as his tools” is applicable. For a thorough water filtration system installation, you’ll need a few basic instruments to ensure that the job is done correctly and properly. The following is a list of the tools you’ll require:

Tools Needed

  • Screwdriver
  • Drill
  • Drill Bits
  • Pipe Cutter or Hacksaw
  • Bucket or Pan
  • Teflon Tape
  • Soldering Supplies
  • Adjustable Wrench

The majority of homes have all of the tools listed above on hand. Even if you don’t have the necessary tools, they are not prohibitively costly and can be acquired at any hardware shop.

Plumbing Supplies that will be Needed

The installation of a functional water filtration system is difficult without the right parts and equipment. Water filter systems for the entire house require only a few basic parts and plumbing supplies to ensure a good installation and to achieve the results you expect from the water filter. Read on to learn more. You’ll need the following basic supplies to finish the installation, which are listed below.

Supplies Needed

  • A proper water filtration system installation is difficult without the right parts and materials. It is necessary to have a few basic parts and plumbing supplies for a whole home water filtration system in order to assure a correct installation and to get the results you want from it. The following is a list of the fundamental items that you will require to finish the installation.

The Installation

It is the same method to install a whole house water filter system as it is to install a single-family home water filter system. With a difficulty rating of five on a scale from one to ten, this game is considered challenging. In a few hours, the majority of individuals with a basic understanding of constructing or mending things will be able to finish the installation of the whole house water filtration system. The video below leads you through the process of installing a basic whole-house water filtration system from start to finish.

Please look into other internet resources to see if they meet your particular requirements and standards.

We’re Here to Help

Water Equipment Technologies (WET) has been a global leader in the design, development, and manufacture of residential, commercial, industrial, municipal, and agricultural water filtration systems for more than 40 years. Water Equipment Technologies (WET) is a subsidiary of Water Equipment Corporation. A broad conventional range of filtration systems is available from WET; however, these systems can be customized to meet your individual requirements. If you require assistance in selecting a water filtration system or in designing a custom system, please contact one of our water technology experts and learn why WET is a global leader in developing water systems to meet the world’s water needs.

More Information about Articles

How to Install a Whole House Water Filter

The clarity, cleanliness, and flavor of your water are important factors to consider whether it comes from a well or a municipal water delivery system. However, this is not always the case. So, other than stocking up on bottled water or shelling out a lot for a state-of-the-art water filtration system, what options do you have? An entire home water filter may be installed, which will offer clean, clear water for all of your household’s requirements. We’re going to put up a whole-house water filter today, so stay tuned.

  • Following that, we’ll go through the many types of filters that may be utilized with our system, as well as the various levels of filtration provided by each.
  • Take the unit out of its packing and inspect it to ensure that we have all of the necessary parts.
  • Let’s get started with some preliminary assembly.
  • Next, using an adjustable wrench, we’ll tighten down the fittings into the head cap, taking care not to over-tighten the assembly.
  • Alternatively, we might have utilized this 3″ mail threaded copper compression fitting, but we would have had to solder the ends of the fitting to the existing water lines.
  • The water supply must be turned off and a faucet must be opened to release pressure in the line prior to installing the unit.
  • This will need some investigation on your part, as well as an awareness of how water comes into the house from the well or municipal supply line located outside the house.
See also:  How To Change Lg Fridge Water Filter

We don’t require filtered water for outdoor consumption.

In order to have enough of space to remove the cartridge for filter replacements, we’re placing our filter on a water line near the ceiling.

Simply ensure that there is 1-1/2″ space below the housing so that you can remove it to replace the filters.

However, because we do not have any slack in the lines, we must use a slip joint push fitting, such as this one, which we have used in other projects for the same reason as this one.

Using this copper tube cutter, we’ll start by cutting a small hole in the existing water line to serve as a starting point.

It may take several minutes for the line to be completely drained.

Notice how the pipe is gleaming at the very end?

The push fitting on one side of the filter assembly is inserted into the pipe to the extent that it will go, which is roughly 1 inch.

Holding the slip joint up to the pipe will allow you to get an approximate measurement of where you will need to cut the pipe on the opposite side of the installation.

To finish off the pipe, use a copper tube cutter to cut away any burrs on the end.

Once this is accomplished, while pushing the disconnect clip against the release collar on the slip end of the fitting, slide the fitting onto the second pipe such that the short copper tube is inserted into the assembly push fitting, once again to a depth of one inch.

Because our electrical system is grounded to the water line, which is a normal practice in many homes, we must attach this copper jumper wire, which functions as a bridge over the plastic water filter to ensure that the water flows properly.

This jumper wire is compatible with these clamps.

Now, let’s put our water filter into the cartridge and see how it works.

It also has the additional benefit of reducing other hazardous pollutants such as mercury and lead.

The housing is unscrewed from the head cap, and the replacement filter is inserted into the cartridge in accordance with the manufacturer’s recommendations.

We’ll manually tighten the cartridge by slowly twisting it in the opposite direction of the clock.

That’s exactly what I was looking for.

You may now receive a nice drink of filtered water from any faucet in the home.

It’s that simple. Not to mention the fact that it enhances the quality of the water that is utilized for other household activities. Our local independent home improvement store provided us with some DIY guidance, which was all it required. Transcript is now closed.

How to choose and install a whole home water filtration system.

Water filtration systems for the home are available in a number of flavors and filter kinds. Before deciding which sort of home water filter system to put in your home, you should educate yourself on the many types and applications of home water filter systems. The following crucial alternatives are among the most important considerations.

Filter type

  • A process known as ion exchange is used to “soften” the water supply. Reverse osmosis
  • Carbon filtering
  • And other methods of purification

Filter system size to fit your kitchen layout and personal preference

It is dependent on the type of system, scale, and complexity that determines the purchase price and simplicity of installation (for DIYers).

Filtration type: Reverse osmosis advantages.

There are a variety of reasons why reverse osmosis (RO) water filtering systems are so popular. This sort of filtration system is straightforward and not overly complicated. The removal of dissolved inorganic solids is accomplished by the use of your household water pressure (typically around 50 to 60 psi). Reverse osmosis filtration is a method of purifying water by forcing it through a semipermeable membrane filter. The question is, how does it function, and why is it a decent water filtering choice.

Many American homes rely on RO for the following reasons:

  • It produces very tasty water
  • It performs its duties in a safe and effective manner
  • Filters are completely automated, and no action on the part of the user is required
  • The ability to offer competitive pricing for RO systems is a crucial element. You will no longer need to purchase expensive bottled water because your clean water will only cost pennies per gallon
  • Instead, you will save money. Installation of a simple kitchen faucet for high-quality drinking water is straightforward.

Carbon filtration systems.

Carbon filters, which are one of the most common forms of household water filtration, are quite effective and provide you with a variety of application possibilities. It is possible that a basic customized canister outfitted with a carbon filter will be sufficient for your household if they are not “water hogs.” Activated carbon filters, which work on the concept of chemical absorption, are used to remove pollutants and impurities from tap water. Because a pound of activated carbon has a surface area equivalent to about 100 acres, activated carbon is exceptionally effective as a water purification filter.

Carbon, on the other hand, is incapable of removing minerals and salts from filtered water.

Water often passes through carbon filters at a lower pressure (and hence at a slower rate) than the water supply pressure, allowing pollutants to be exposed to carbon filters for a somewhat longer amount of time, resulting in even greater efficiency for these filters.

This demonstrates the efficacy and adaptability of activated carbon filters for a variety of applications.

Filtration type: Ion exchange.

Ion exchange water filters are popular because the water passes through a resin that replaces undesirable ions with more acceptable ions after passing through it. Ion exchange technology, which substitutes any calcium and/or magnesium in your tap water with sodium, is a prominent use for the technology. Ion exchange filtration systems “soften” the water that enters your home through the plumbing system. Often, city or well water is “hard,” meaning it has a high concentration of contaminants. Water softening is currently considered a critical outcome in filtration systems that filter the water used for drinking and cooking in your house.

Ion exchange resins (polymers) serve as media in these filtering systems, which are used to achieve water softening and incoming water purification while also removing ions from the water.

Because these resins (polymers) are porous, they allow the medium to replace undesired ions and contaminants in your home’s tap water, resulting in cleaner drinking water.

Ion exchange resins are available in four different flavors, each of which serves a different functional purpose. The following are the four sorts of cultivars included in this group:

  • “Strongly acidic,” which are found in the majority of water softening filtration systems
  • “Strongly basic,” which are based on amino acid groups
  • “Weakly acidic,” which are typically based on carboxylic acid varieties
  • And “Weakly basic,” which are based on amino acid groups that are weaker in nature.

The major purpose of most ion exchange filtration systems for the household and small businesses is water softening. The more difficult the water supply is, the more you should consider ion exchange filtration as a water treatment solution.

Filter size: Under sink installation.

The installation of a kitchen faucet under the sink avoids the need for large filters at the ends of the faucet arm. Individual sinks benefit from this sort of installation since it is the most cost-effective option. You might consider purchasing the bigger “whole home” system if you have three or more bathroom sinks and, therefore, sinks, because you will ultimately tire of putting multiple under sink purification equipment. If you are a fairly proficient DIYer with plumbing jobs, you may save money by installing your under-sink system yourself rather than having your favorite plumber do it.

Under the kitchen and bathroom sinks, there should be enough space to accommodate an under-sink water system of each kind (reverse osmosis, carbon filtration, and ion exchange).

Whole house installations.

These are the most comprehensive and intricate systems available for your house. Whole house installations are often employed when you are concerned about the quality of your household water in more than two spots throughout your home. The installation of these filtrations is the same for all filter types since the only differences are in the manner the water is filtered and the impurities that are eliminated by the filters. In order to do this project on your own, you’ll need the following materials and tools.

  • It’s a drill
  • Drill bits in various sizes
  • There are two different-sized adjustable wrenches. A tubing cutter is a device that cuts tubing. Buckets (plural) to capture any residual water in your main water supply after it has been turned off
  • Water filtration system for the entire home

Select a place that is close to the main water supply for your property. You want to make sure that replacing the filters in your system is a simple process. Keep in mind that you are filtering the whole incoming water supply for the entire household. *If you want to install a whole-home water filter system on your own, follow these procedures.

  1. Choose a place that is conveniently accessible while still being close to the main shutoff valve. In order to change the filter system when necessary, make sure you have enough room under the filter system. Remove the pipe and replace it with a new cutoff valve. You should be aware that you will likely want an adapter on each side of the filter to connect your pipe size and your new filter. Assemble the filtering system to ensure that the filter can be accessed and replaced without difficulty. Once you are pleased with the simplicity with which a filter change may be accomplished, you can mark it for cutting. Make a mark on the pipe in order to make an exact and useful cut
  2. It’s time to put the new filtering system in place. Keep in mind to slip on the compression rings and tighten the nuts to ensure a tight, leak-free fit between the two pieces of pipe. To ensure a secure connection, tighten the bolts. You may now re-open the main water valve to allow the water to flow again. Check for leaks or tighten your connections to ensure they are secure. If you already have a ground wire connected to your water supply pipe, you will need to connect a jumper cable to it in order to restore this functionality.

You have now completed the installation of a very effective whole-house water filtering system. Congratulations!

Summary and conclusions: The perfect home water filter for you.

You should now be aware of the many filtration choices accessible to you. Prices for each filter type, as well as for expert installation services, vary from one region of the United States to another. We recommend that you have your water tested to learn about the pollutants that may be present in your municipal water or well. You will know what sort of filter you need (reverse osmosis, carbon, or ion exchange) once you have tested your tap water. You may use this information to install a countertop, under-sink, or whole home water filtration system.

If the installation looks to be a larger undertaking than you are comfortable taking on, don’t be afraid to call in a professional, such as a member of the Petro Home Services team for assistance.

Unless you remember to do so, you will be greeted with an unpleasant “water under pressure” surprise.

A whole home filtration system, on the other hand, may be the best option for you if you want your shower and “wash up” water to be pure as well.

Please get in touch with us if you have any questions regarding our home water filter installation services. * The Home Depot is a retailer that sells a variety of home improvement products.

Tips on How to Install a Whole House Water Filtration System

You cannot be certain that the water that comes out of your faucets is clean and devoid of pollutants 100 percent of the time. Throughout the years, there have been several concerns raised about the cleanliness of municipal tap water. Many of these concerns have been addressed by water laws; nevertheless, the best way to ensure the purity of our tap water is to take matters into our own hands and install a whole-house water filtration system to safeguard our loved ones. Completely installed at the point of entry, whole home water filters not only clean your drinking water but also the water used by your shower, dishwasher, laundry, and other household appliances as well as the water used by your pets and children.

See also:  What Size Tankless Water Heater Do I Need For A Family Of 5

After you have made the investment in your new system, follow these guidelines to make the installation procedure much more straightforward:

Check if the installation requirements fit your home

Before choosing a whole-house filtration system, take careful to research the installation requirements to ensure that the unit you choose will be suitable for your home’s requirements. Whole house water filters are available in a variety of sizes, and the majority of them must be put indoors or at the very least in a protected area. Not all systems are suited for all types of household fittings, so be sure that the system you choose is compatible with the fittings in your home in general. Otherwise, you may be forced to deal with the return of the filtration system, or worse, you may be forced to deal with a filter that has not been fitted properly.

Use a pressure reducing valve if your water pressure is too strong

The manufacturer of the model you purchase should provide you with specific information about its maximum pressure restriction. It is possible to purchase a pressure lowering valve separately and install it to your fixtures if your water pressure is too high. Keep in mind that the pressure may be different at night than during the day. It is possible that the water pressure at night is greater than the water pressure during the day. Therefore, be sure to check at various times of the day and night to evaluate whether or not you may require a pressure-reducing valve.

Connect your filtration system directly to the main supply before your water heater

Because most water filtration systems are designed to function with cold water, it is possible that the system will be destroyed if it is forced to utilize water from the heater. Even when cleaning, you should never put hot water through the system since it might cause it to malfunction. Installing the system in an area where the water in the system would never freeze is also recommended, particularly during the winter.

Install a pre-filter before the filtration system

Depending on the quality of your water, a pre-filter may be required to assist you in producing the cleanest water possible while also extending the lifespan of the water filtration system that will be installed later. It is also possible to add a bypass system for the water path. In this way, replacing the pre-filter and troubleshooting any difficulties that may arise will be much simpler.

You may learn more about our highlighted pre-filter by visiting this link: WSP50ARB Water Filter with Scraper for Reusable Spin-down Sediment Water Filter with Touch-Screen Auto Flushing Module

Turn on the nearest faucet before installation

The first stage in your installation process is to switch off the main water supply. However, because pipes and tubes are often laid horizontally, it is possible that some air and water will remain in the pipes after they have been filled. Start by turning on the nearest faucet to remove any of the air and water that has built up within the internal parts. This will help to avoid any spills or leaks during the operation.

Use a bucket to catch water after cutting the main inlet pipe

A section of your main water supply pipe will need to be cut in order for the filtration system to be properly installed. It is possible that residual water will remain inside the mainline; thus, place a bucket beneath the spot where you plan to cut to catch any water that drops. Alternatively, you may place a cloth beneath the aperture, although this is less effective than using a bucket because you will need to use both hands while working. Unwanted pollutants and pathogens in the water can be prevented by installing a whole-house water filtering system.

Using these suggestions will assist you in avoiding making a sloppy mess when assembling your new filtration system.

We will be happy to assist you.

Guide to Whole House Water Filter Price, Cost and Installation

When it comes to finding the best whole home water filtration systems on the market, it may be quite difficult. Trying to compare one whole house water filter with another while looking at price and costs, as well as reading reviews and ratings, is nearly difficult if you don’t know anything about how whole house water filters function. How are you expected to determine which model is the best fit for your needs and preferences? Even yet, investing in a whole-house water filter is a wise decision for homeowners who are worried about the quality of their drinking water.

Activated carbon (sometimes known as “charcoal”) is used in virtually every whole-house water filter for water filtering purposes.

Impurities and chemical-based substances may be removed from water sources with remarkable efficiency thanks to carbon. The majority of the carbon utilized now is derived from natural coconut shells, which has mostly replaced the bituminous coal that was formerly prevalent.

Benefits of WholeWater Filtration

There are several advantages to installing a whole home water filtration system at the point of entry (POE) as opposed to a point-of-use (POU) water filter. Every tap in your whole home is filtered through the point of entrance. There is no longer a requirement for separate shower filters and drinking water filters to be installed. In general, point-of-entry filters are more cost-effective than other types of filters since they don’t have to be replaced as frequently and they endure for a longer period of time.

Compared to the rapid “pass through” showers or facet filters, bigger mineral tanks provide higher filtration and water quality.

Things to Look For

When searching for a new whole-house water filter system, there are a few things to keep in mind in general. When comparing brands, these might assist you in narrowing down your search.

Capacity

The capacity of a water filter media (or cartridge) indicates how long it will last before it has to be replaced. Once the media no longer has the ability to remove pollutants, all water filters will need to be changed. The majority of the time, filters are rated according to their capacity in terms of months, years, or gallons. Because carbon behaves like a sponge, it will not be able to absorb or eliminate contaminants if it is left in water for an extended period of time or if an excessive amount of water runs through it.

If you exceed the manufacturer’s recommended cleaning time, you may notice a reduction in the amount of impurities that can be removed.

In this particular instance, a straightforward chlorine test strip is just what you want.

Gallons per Minute (Flow Rate)

Your flow rate will be determined by the size of your home, the number of people that live there, and/or the number of bathrooms you have available. Water flow will not be reduced during peak-use hours (such as the early morning), when you may be using the kitchen faucet as well as a couple of showers while doing laundry if a whole-house water filter is installed correctly. Look for the flow rate to ensure that the water system you’re considering purchasing is correctly sized.

Filtering Type

Is there a significant amount of silt in your water supply? If this is the case, a sediment filter is usually a good option. Good sediment filters are capable of filtering particles down to sizes that are smaller than the width of a human hair. Microns are the most often used unit of measurement. Using a five micron filter (such as the one we use at Filtersmart) is sufficient for capturing particles while maintaining consistent and strong water pressure. The next step is to establish whether the filter is made of a carbon block or granular material.

We’ll explain later why we believe granular media are preferable than blocks in this situation. As well, look to see if the media contains normal carbon for chloramine removal or catalytic carbon for chloramine removal, depending on what you want for your drinking water.

What Do Whole House Water Filters Remove?

If you want to consume water that is cleaner and healthier, you must take into consideration what is in your water. There are several alternatives available on the market, and if you’ve only recently begun looking into whole house water filters, you’ve definitely already read a number of reviews and comparison articles. This guide is intended to assist you in determining what type of whole-house system you will require. The first thing you should find out is what sort of disinfection is being used by your local water department.

What is the significance of this?

If, on the other hand, your municipal water contains chloramines, you will need to make certain that the carbon you use is catalytic carbon, which is designed particularly for chloramine removal.

You may also try searching for “water quality report” in your city and zip code, as well as the terms “water quality report.” Typically, you’ll be able to pull up the report that has the disinfectant that was indicated.

Installation of Whole House Water Filters

In general, there are a few alternatives for whole-house filtration that you would need to take into consideration while making your decision.

Comparing In-Line Whole House Water Cartridge

An in-line filter is typically comprised of a carbon block enclosed within a housing unit. In-line filtration systems are one of the most affordable solutions for homeowners in terms of upfront costs. The problem with in-line filters is that they have a limited capacity for water. The majority of them have a one-year or 100,000-gallon warranty. To ensure maximum filtration, you would need to replace these carbon blocks on a regular basis, perhaps even more frequently if you have any outside irrigation systems.

The cost of a replacement is $285.50.

The most significant disadvantage of in-line filters is their potential to quickly induce channeling.

It is possible to achieve greater removal with a mineral tank system because it provides longer contact time and because there is no channeling that might lower reduction rates.

Additionally, the filtration capacity is around 10-20 times greater. In short, in-line water filters are an excellent low-cost introduction to whole-house water filtration, but the yearly replacement costs practically cancel out any initial savings a homeowner could get from using them.

Downflow Whole House Water Filter Systems

Lifesource is one of the most well-known and commonly used downflow granular activated carbon water filtering systems on the market, however there are many more comparable models and variants available from local firms. They are all designed to work in a downward flow orientation. The water flows into the tank, via the bottom screen, up the distributor, and out to the water supply. These systems require a weekly backwashing cycle to reset the bed and avoid channeling, which necessitates the use of power as well as a water drain to flush the water out of the system.

It’s unclear why, but these basic granular activated carbon filters are frequently offered for between three and four thousand dollars in the United States.

When you include in the expense of a simple 3-4 hour installation by a local plumber, the cost of these systems is nowhere near justified in the eyes of the average homeowner.

Up-Flow Whole House Water Filter Systems

FilterSmart water systems employ granulated activated carbon filters that are placed in the upstream flow of the water. They operate in an upward flow direction, consuming no power and generating no waste water. Another significant advantage of this design is that when the carbon media becomes ineffective, you can simply switch the carbon for fresh media and continue to use the tank as is until the carbon media is replaced. Our tanks are backed by a limited lifetime guarantee. The carbon in the tank may simply be replaced, and the tank can continue to be used indefinitely once the media has expired, which is after five years or one million gallons.

That works out to $149 every five years.

At FilterSmart, we only provide the highest quality products.

When it comes to people who have chloramines in their water or those who have a limited budget, in-line and downflow systems are not an option.

Where are Whole House Water Filters Installed?

Point-of-entry (POE) systems, such as whole-house water filters, are classified as such. In most cases, they are put outside your home or within your garage, on the main water line that supplies your home. Some houses will already have a water softener or filter loop installed in their garage, which makes for a quick and simple installation process. In most cases, whole home water filters may be installed by anybody with a basic understanding of plumbing, or, of course, by a licensed plumber.

See also:  What Is The Average Life Of A Water Heater

For those who don’t already have a filter loop, you may either build one yourself or just connect it to the main water line near the water shut-off valve.

You should also inspect the line prior to the installation site to ensure that there are no splits in the line. Depending on where the water line divides before the whole-house water filter, you might be left with just half of your house receiving cleaned water.

Do I Need to Soften the Water Before I Filter It?

If you’re shopping for whole-house water filters, you might be wondering whether you’ll need to handle the hardness of the water as well as the other contaminants. The majority of whole-house carbon filters do not include any choices for treating the hardness of your water supply. Hard water is not considered a pollutant; rather, it is seen as a nuisance for your plumbing, appliances, and faucets because of its abrasiveness. In addition to being caustic, hard water stains or limescale deposits can cause a rise in water heating bills as well as clogging in your water pipes or lines.

If you have hard water problems, you may want to consider installing a filter and water softener combo system.

Best Whole House Water Filters and Water Softener Combination

The most popular systems on the market are the combination systems, which include a whole-house water filter as well as a second tank for a water softener and are thus the most expensive. Combo systems are quite popular because they are ideal for the vast majority of American houses that suffer from poor water quality and high water hardness levels. When it comes to water purification, this combination is unbeatable. There is some degree of hard water in the great majority of American houses, and all municipal water will contain a disinfectant – not to mention any number of other toxins that may make their way into your water supply.

These places tend to be soft, which is why we offer our whole home water filter mostly to those who live in these areas.

If you’re not sure whether or not you need a softener, you may always start with a whole-house filter and then upgrade to a softener.

Final Thoughts on Whole House Water Filters

One of the most effective options for people seeking to reap the advantages of filtered water from every faucet in their home is to install a whole house water filter. It’s important to read reviews and compare product specifications to ensure that you know exactly what the water capacity rating is and what filtering material is being utilized. If you’re shopping locally, make sure to check costs with those you may find online before making your purchase. Many homeowners have complained to us that local water sellers have given them ridiculously high quotations.

For years, local water merchants have been criticized for using high-pressure sales methods and raising their prices unfairly.

They’ll frequently include installation in the price of their goods, but charge an outrageous sum for it on top of that. You may save a lot of money if you order from a manufacturer directly online and have a local plumber do the installation for you.

Review

Make certain to conduct thorough research and to consult with your local water department on the water quality. Most whole house water filter systems do not employ any catalytic carbon as the filtering medium, which is necessary for getting rid of chloramine, which is becoming increasingly common. It’s important to contact the manufacturers or local water softener dealers to obtain information on the filtration medium or requirements. You must be aware of exactly what you are purchasing. Watch out for websites that claim to be independent “review” or “comparison” sites, but are actually affiliates wanting to make a fast money.

It is common for them to just evaluate or compare things on Amazon because it has the most prominent referral network in the world.

While we recognize that you have many choices, if you have any questions about anything you see, please contact us at 866-455-8898 and we would be happy to assist you with your water requirements.

Please do not hesitate to contact us at the following address: Please contact us at 866.455.9989.

Where should I install my whole house water filter?

Whole-house water filtration systems should be put as close as feasible to the point of entry of your water supply to ensure the best possible protection. This is often located near your water heater, and you want it to be placed prior to the water flowing into your water heater, if possible. Due to the fact that your filter will clean the water, it will eliminate the need for your water heater to deal with’scale’ caused by hard water or other varied sediments and weird stuff from your water supply.

Before you can decide the best location for your filtration system, you must first establish whether you are receiving your water from a well or a municipal source of water.

Well Water Installation

Most of the time, if you have a well-water system, the “chain” that passes through your system looks something like this: initially, you have your well pump. After that, you’ll need to build up some form of pressure tank. This is where the ‘wrinkle’ in the game begins; many manufacturers recommend that you install your whole-house water filtration system AFTER any type of water softener, and before the water heater, in order to avoid contamination. This is apparently done to allow for maximum flow so that the softener can properly backwash.

For the sake of allowing for an untreated line, it is advised that you separate your pipe flow before the water softener and filter system.

The majority of individuals want this untreated water to be sent to exterior water spigots and/or any type of irrigation or sprinkler system that may be installed at their residence.

Installation for Municipal Water Supply

When it comes to connecting a central water filtration system to a municipal water supply, the procedure is the polar opposite of that described above. Despite the fact that you must still divide the line so that untreated water may be used for plants and sprinklers on the exterior, you should install the filter before the water softener in this situation. This is due to the fact that you don’t really have any problems with water pressure while using municipal water sources. The fact that well water often contains a different composition of elements than municipal water is still another explanation.

  1. The filter should be placed in front of all of your other equipment in this situation.
  2. After all, why wouldn’t you do the same thing with well water?
  3. In the event that you’re concerned about unclean water passing through a large portion of your equipment and you’re using well water, you can always add a tiny cartridge sediment filter to the beginning of your chain.
  4. If you ever find yourself in a situation similar to the one described above, adding a cartridge filter to your chain can help you address a variety of problems.
  5. Double-check all of your connections, and remember to replace your filter whenever it is advised by your manufacturer.
  6. Always check the user manual that came with your filter system for precise installation instructions for your individual filter.

How Much Does It Cost to Install a Whole House Water Filter?

When it comes to connecting a central water filtration system to a municipal water supply, the procedure is the polar opposite of what was just described. In this scenario, you want to install the filter before the water softener because you still want to be able to send untreated water outdoors to plants and irrigation systems. Due to the fact that municipal water sources provide adequate water pressure, this is the case. The fact that well water often contains a different composition of elements than municipal water is still another factor.

  1. The filter should be placed in front of all of your other equipment in this situation.
  2. You could do the same thing with well water, after all.
  3. A tiny cartridge sediment filter might be added to the beginning of your chain if you are concerned about unclean water passing through a large amount of your equipment and you are using well water.
  4. Dropping a cartridge filter into your chain can alleviate a lot of problems if you ever find yourself in a situation like the one described above.
  5. Check all of your connections, and always remember to replace your filter when the manufacturer recommends it.

Make sure to refer to the user manual that came with your filter system for precise installation instructions for your individual filter system. Also see: The 8 Best Countertop Water Filters for 2021 (with Pictures).

Cost factor1:The type of water filter

The following are some of the most common water filtration systems in Connecticut.

Activated Carbon Filters

Typically, prices range from ($450 to $2,700+). These devices, which are also known as carbon or pre-carbon filters, are used to remove big particles from your drinking water supply, such as sediment and silt. They function by attaching themselves to or absorbing them from your tap water. One of the most significant advantages of utilizing activated carbon filters is that your tap water will have a decreased odor and a better flavor as a result of the filter. In addition, the presence of chlorine and other impurities has been greatly reduced.

Reverse Osmosis Systems

Typically, prices range between $1400 and $1500 or more. Everyone who has had the pleasure of drinking water from a glass that came from someone’s house that was equipped with a reverse osmosis system can attest to how pure and pleasant it can be. When it comes to drinking water, reverse osmosis systems employ a high-pressure pump to remove impurities and poisons from the water in your house. This sort of water filter is only required in specific types of residences since it treats the more serious impurities that are commonly present in private wells.

system works.

Water softener

Typically, they run from $1,600 to $3,000 in price. In the context of water treatment, a water softener is a device that “softens” hard water by eliminating the minerals that cause it to be hard. Water softeners are primarily employed in the treatment of hard water. Hard water is defined as water that has a large amount of minerals, often high amounts of calcium and magnesium. Having hard water in your home’s plumbing system may cause sediment accumulation in pipes and plumbing fixtures over time, which can be a concern.

Flow-Tech systems

Typically, prices run between $1,000 and $2,000 per hour. 24 hours a day, seven days a week, Flow-Tech water treatment systems treat all of the water in your house. The technology generates a low-frequency signal that is pulsed many thousand times per second and propagates throughout your whole plumbing system, causing it to malfunction. The charge on the minerals that are dissolved in the water is reversed as a result of this electromagnetic signal.

Whole house water filters

Typically, prices range between $400 and $10,000. Whole-house water filters are point-of-entry systems, which means that they connect to the main water line and clean all of the water that enters your home from that point. Allowing you to use filtered water in the shower, kitchen, bathrooms, and even your laundry is a good thing. Whole-house systems are mostly used to remove chlorine and bigger particles from water in order to improve the appearance of the water and extend the life of your plumbing system and appliances.

Unsure whether your water from the tap is safe to drink in Connecticut?

Connecticut’s public water sources only employ the finest quality waters that are protected by a slew of rules designed to protect the public’s health. Connecticut is one of only two states that restrict the release of wastewater treatment facility effluent into watersheds that feed public water supplies.

As a result, our public water sources are at low danger of contamination with drugs and other toxins. More information may be found here: Is it safe to drink the tap water in Connecticut?

Cost factor2:Your current plumbing system

If you do not have the right plumbing system in place for your water filter, the overall cost of installing your water filter will be more than it otherwise would be. The cost of adding plumbing varies greatly from home to home, but it can add anywhere from $800 to $5,000 or more to the overall cost.

Cost factor3:The installation pricing of the plumber

In general, more experienced, high-quality plumbers will charge more for their services than less experienced plumbers. This is also dependent on the size of the work, the weather conditions, and the finish options you select. It is true that you get what you pay for when it comes to installing a whole home water filter. A skilled plumber will provide you with expert service and a high-quality installation that will save you money and time in the long run.

Leave a Reply

Your email address will not be published.