What Temperature Should I Set My Water Heater At?
Get in Touch With Us
Setting the Ideal Hot Water Heater Temperature
Are you tired of burning your hands every time you turn on the hot water in the shower? What if you’re having trouble getting a comfortable water temperature, no matter how high you turn the faucet up? These are not always indications that your water heater is malfunctioning, but rather that the temperature setting you have chosen is not optimal for your purposes. A water heater that has been installed incorrectly can have a significant influence on your life, even in areas that are not directly linked to your plumbing or heating system.
It can also have a negative influence on your health or the health of people who share your home with you.
A definitive or simple response cannot be given; rather, part of it is a matter of personal choice.
General Recommended Water Heater Temperature
You can find out what temperature water should be at by visiting the Environmental Protection Agency. The optimum water temperature is 120 degrees Fahrenheit. You will really save money because your water will not be hot enough to cause scalding, most small households will have adequate hot water for their needs, and reheating will not need an excessive amount of energy consumption, allowing you to save money on your utility bills. This temperature, on the other hand, is not ideal for everyone.
Considerations When Choosing a Water Heater Temperature Setting
Do you have any at-risk individuals residing in your home? Those who are particularly sensitive to high temperatures may suffer serious consequences if they are exposed to overly hot water. Water at 150 degrees Fahrenheit may cause third-degree burns in newborn babies in only two seconds, while water at 140 degrees can cause third-degree burns in babies in just five seconds. Temperature reduction is more safer for your infant and far more cost-effective in terms of energy use. A water heater set at no more than 130 degrees is recommended if you have a baby or any youngster under the age of three in your household.
- Those who have compromised immune systems or who suffer from respiratory ailments, on the other hand, may benefit from a hotter water temperature in order to destroy bacteria while also increasing the concentration of steam in the air when bathing.
- Do you have an appliance that is energy efficient?
- Essentially, these systems take in water and then raise the temperature to even higher levels to provide an even better and more hygienic clean, all without the need for you to raise the temperature coming from your water heater.
- If, on the other hand, it won’t be for a long time, you may wish to raise the temperature of your water heater to 140 degrees.
- How many people do you have living in your house?
- Those who like a hotter shower increase the ratio of hot to cold water in their shower.
- The temperature of the water that comes out of your water heater, on the other hand, will have an impact on this as well.
- People that use cooler water heaters will require more hot water and less cold water in order to achieve their goals.
- If you have a large home with multiple people living in it, you should raise the temperature of the water to ensure that your hot water supply lasts as long as possible.
Do you require assistance with your water heater in the Los Angeles area? Whether you want a thermostat replacement or the installation of a new water heater, contact the professionals at Moe Plumbing Services at (818) 396-8002 now.
More on Water Heaters:
- Six Common Problems with Your Home Water Heater
- What Every Homeowner Should Know About Water Heater Maintenance
- Six Common Problems with Your Home Water Heater
Best Temperature for a Water Heater
What is the optimal temperature to set the water heater at? That is a question that many homeowners have. Previous PostNext Post This is a fantastic question, and the information provided by Aire Serv® will help you to enhance the performance, efficiency, and safety of your water heater by following the guidelines.
Determine the Best Temperature for Your Water Heater
The usual setting for most water heaters is 140 degrees Fahrenheit, but the Department of EnergyLink opens in a new tabrecommends lowering the temperature to 120 degrees Fahrenheit in order to conserve energy. To summarize, you shouldn’t drop the temperature of your tank below 120 degrees because doing so encourages bacteria development (unless you are traveling out of town, in which case the DOE suggests lowering the temperature to its lowest level). Consider the following factors that influence the temperature at which you should set your water heater:
- The normal setting for most water heaters is 140 degrees Fahrenheit, but the Department of EnergyLink opens in a new tabrecommends lowering the temperature to 120 degrees Fahrenheit in order to conserve energy. Just remember that any temperature setting below 120 degrees encourages bacteria growth within the tank, so you shouldn’t go any lower than this (unless you’re traveling out of town, in which case the DOE suggests putting the thermostat down to the lowest level). Keep in mind these factors that influence the temperature at which you should operate your water heater:
How to Adjust the Water Heater Temperature
Perhaps you want to raise the temperature of the water heater to assist your dishwasher in doing its work more effectively, or you want to lower the temperature to reduce scalding. In any case, the following actions should be followed to alter the water heater setting:
- Obtain an accurate reading of the present temperature by turning on hot water at a faucet that is the furthest away from the water heater, as shown in the diagram. Place a thermostat under flowing water to see whether or not an adjustment is required
- Locate the thermostat dial by turning it clockwise: Gas water heater tanks include dials towards the bottom of the tank that regulate the temperature of the water. Water heaters that run on electricity frequently have their thermostats tucked away beneath screw-on panels. If your electric water heater contains upper and lower heating components, there may be two dials on the control panel. Take the following measurements and make the necessary adjustments: Increase or decrease the temperature setting on the thermostat by a little amount from its beginning level. Then you’ll have to wait a few of hours. Measure the water temperature once more and make any additional modifications that are necessary. Whenever you’re through, make a note of the final temperature on the dial so that you may quickly adjust it in the future.
Other Ways to Improve Water Heater Efficiency
In addition to lowering the thermostat, you may make these energy-saving modifications to your residence. To lower your water heating expenses, click on the following link, which will open in a new tab:
- Insulate the water heater tank to decrease heat loss during standby mode. Renovate your bathroom by replacing your showerheads and faucets with low-flow models that use less hot water. Replace your existing water heater with a tankless one that warms water on demand, eliminating the need for storage and the accompanying standby heat loss.
Schedule Water Heater Services with Aire Serv®
Whether you need assistance changing the temperature of your water heater or you want to arrange water heater repair or replacement, you can rely on Aire Serv to complete the task. We’ll help you save money by providing thorough water heater repair services and replacing your water heater when it approaches the end of its useful life. Please call Aire Servtoday if you would like to schedule water heater services with a qualified expert. Previous PostNext Post Previous Post
What Temperature Should a Hot Water Heater Be Set At?
Previous PostNext PostYour water heater accounts for around 18 percent of the energy consumed by your house. If the temperature of your water heater is set too high, you will be forced to pay the price in your monthly energy bill. The converse is true: if you have your water heater set too low, your water may not get hot enough (resulting in short showers), or worse, it may get contaminated with germs. Maintain a 120-degree temperature for your water heater at all times because infections can form in the stagnant water within the water heater, notably Legionella, which is extremely deadly.
In addition to being hot enough to keep viruses at away while not being scorching hot enough to cause blistering, 120 degrees will provide adequate hot water for most small households while still being relatively energy-efficient, according to the Environmental Protection Agency.
Factors That Affect Hot Water Temperature Setting
These criteria are unaffected by the kind of piping you have (PEX, PVC, or copper), the method of heating the water (gas or electric), or even if you have a tankless hot water heater installed.
- Owners of dishwashers that do not pre-heat the water may wish to set their water heater temperature to 140 degrees
- Elderly or families with young children may want to keep the temperature at 120 degrees. BabyCenter.com states that “it takes just two seconds for a kid to acquire third-degree burns from water that is 150 degrees and five seconds if the water is 140 degrees, the temperatures at which hot water heaters frequently leave the manufacturer.” It is recommended that the hot water temperature be maintained at 140 degrees in homes with people who have a compromised immune system or respiratory problems. Because there is less demand for hot water and hence less money spent on hot water, many people who live alone prefer a lower temperature within an acceptable range. The temperature of the water tank is often set higher in big households, in order to support the increased demand for hot water
- Nevertheless, if you want to save money, every 10 degrees you lower the temperature of the water tank thermometer, you save 3 to 5 percent on your energy bill.
Are you still undecided? To begin, set the temperature to 120 degrees Fahrenheit and gradually raise it in small increments until you reach the desired shower temperature.
What’s Your Current Temperature Setting?
Check the temperature setting on the water heater (if one is available) or take a temperature reading from the faucet to determine what it is currently. After turning on the hot water faucet, allow it to run for a few minutes before getting the temperature reading.
Solutions to Common Hot Water Tank Problems
If you’re concerned about pathogens in your hot water, as well as the possibility of scalding water, you might consider installing a hot water tank booster. This allows you to maintain your water at 140 degrees in the tank while mixing it with cold water to bring the temperature down to 120 degrees before it reaches the faucet. Having a hot water circulating system installed in your home might alleviate the problem of waiting for hot water to reach the faucet in a large household. This method circulates hot water slowly through the pipes in order to prevent it from cooling down before it reaches the faucet.
Professional Plumbing Services
It’s possible that your hot water isn’t hot enough no matter what setting your water heater is set to. If you need assistance adjusting your hot water heater or troubleshooting any difficulties, call your local Mr. Rooter Plumbing at (855) 982-2028 or submit a request for a free estimate on our website. Not only does your hot water need to be “just perfect,” but so does everything else in your home. Aire Serv, a neighborly firm, can assist you in determining the optimal air temperature. Previous PostNext Post Previous Post
Risks Of Too High Or Too Low Water Heater Temperature
You might be wondering what temperature to put your water heater to. When you purchase a water heater unit, the temperature is typically set by the manufacturer. However, this does not rule out the possibility of having some control over its temperature. The good news is that you may set the temperature to a level that is comfortable for you while yet ensuring the safety of your family. Previous to this, we wrote an article in which we spoke about how the heat in your shower might suddenly vary.
The temperature of the device is important since it can have an impact on how well it performs.
Top Risks of setting your unit temperature too high
An skilled plumber would advise against raising the temperature of your unit over the recommended level since it might endanger the safety of your children. It can also have an impact on your utility costs and the heater itself. In order to assist you, we have listed the following risks:
1. Scalding Accidents
Setting the temperature too high might result in scorching mishaps that result in burn injuries. According to the findings of a study on water heater temperature and attributes, many water heaters are frequently set at dangerously high temperatures. Several studies by the Centers for Disease Control and Prevention (CDC) have discovered that scald burns are the most common cause of injury in younger children. Every day, over 300 children between the ages of 0 and 19 are treated in emergency departments for burn-related injuries, with two of these children dying as a result of their injuries.
In order to avoid tap burns, experts strongly recommend that you have your water heater inspected. Accidents such as this may be prevented by allowing your water to flow for three minutes and then monitoring the temperature with a candy thermometer thereafter.
2. High electricity bill
Setting the temperature too high might result in scorching mishaps that result in burn injury. According to the findings of a study on the temperature and features of water heaters, many water heaters are frequently set at potentially hazardous temperatures. According to the Centers for Disease Control and Prevention (CDC), scald burns are the most common type of injury suffered by younger children. Burn-related injuries affect around 300 children between the ages of 0 and 19 every day, with two of these children dying as a result of their injuries.
Using a candy thermometer to monitor the temperature of your water after it has been running for three minutes will help you prevent these mishaps.
3. Lowers your unit’s service life
According to some sources, hot water can accelerate the accumulation of hard water mineral silt, particularly calcium carbonate, in the tank’s interior. It is possible that the buildup would cause corrosion in the water heater tank, which will result in a reduction in the estimated lifespan of the complete device. Leaks and polluted water might occur as a result of the rust accumulation in the storage tank. Another major reason for water heater failure is the deposit of rust on the interior of the heater.
We wrote an essay about why it’s important and how you can extend its lifespan.
Risk of setting your unit temperature too low
If you want to save money on energy costs, you should avoid setting the temperature of your unit too low. It is possible that you will have a health problem as a result.
1. Legionnaires disease
Every year, around 100 people in the United States are sent to hospitals due to a form of bacterial illness that can be caused by water heaters. The infections connected with the bacterium were responsible for up to 12 percent of the country’s death rates. Specifically, the Legionella bacteria are responsible for this particular kind of atypical pneumonia. It is common to find this bacterium in water at low temperatures — often between 20 and 45 degrees Celsius. You can contract the disease if you inhale small water droplets in the air that contain germs that cause it.
Evidence indicates that the majority of the bacteria’s spread occurred through the provision of drinking water in private residences.
It has been shown that the danger of contamination is significantly reduced when water heaters are set at 60°C or 140°F.
Ideal Temperature For Your Water Heater
The optimum temperature is. What several agencies have to say about the optimal temperature is summarized below: According to the Occupational Safety and Health Administration (OSHA) and the World Health Organization (WHO), water heaters kept below 60 degrees Celsius (140 degrees Fahrenheit) may promote Legionella development. This temperature, on the other hand, will almost certainly increase the likelihood of being burned by searing hot water. If you have young children at home, the Centers for Disease Control and Prevention (CDC) and the Energy Department recommend that you set your water heater’s thermostat to 120°F or lower.
To do this, set your thermostat to a steady temperature. This will help you keep control over the water temperature throughout your home, preventing it from being overly hot.
So, is it 120°F or 140°F?
We recommend keeping the temperature between 120 and 140 degrees Fahrenheit. However, you may regulate the temperature of your water heater between 130 and 140 degrees Fahrenheit, which is very useful for large water heaters used in hospitals and industrial settings. In case you have little children at home, set the temperature to 120°F, which is considered safe by the majority of the population.
Your installer can help you adjust your water heater temperature.
As part of our service, our qualified specialist at SPS Plumber can assist you with setting the temperature of your water heater to the proper setting. In addition, we can do annual water heater maintenance on your unit. To schedule an appointment, please call us at 408-622-8183 (South Bay Area) or 209-597-9107 (Central Valley) right away!
Setting your water heater’s temperature for best results
time required for reading: 2 minutes It’s possible that you don’t give your water heater much thought, but it actually plays a very crucial role in the plumbing of your home. In addition to higher power expenses, a malfunctioning water heater might result in water that is either scorching hot or ice cold. It is critical to plan annual maintenance to verify that your device is clean (hard water build-up can be detrimental to your water heater) and that the temperature range is within acceptable parameters.
- Setting the Water Heater to Its Optimal Performance Professionals recommend that you keep the temperature of your water heater between 130 and 140 degrees Fahrenheit at all times.
- While increasing the temperature over the suggested setting might result in burns, decreasing the temperature below the recommended level can also be hazardous.
- This might become a health danger for you and your family, putting you and your loved ones at risk of contracting diseases such as Legionnaires’ illness.
- Check the temperature of your water heater.
- The presence of sediment accumulation and calcification in the hot water tank itself will also be checked by a professional if the temperature on the water tank has been changed but you are still experiencing the same water temperature as you were before the temperature adjustment.
- After draining the tank, a professional can attempt to address the problem by scraping off any scale that may have built up over time and soaking the components in hot water.
- The average lifespan of a hot water heater is predicted to be between 8 and 12 years.
- Water heaters require regular maintenance.
- If you want to ensure that your water heater continues to function effectively, you may want to consider hiring a professional to perform this maintenance.
Maintaining your water heater’s temperature between the appropriate ranges is essential. This will prevent any bacteria from growing in the cold water and will protect you from being scalded by a shower that is much hotter than you anticipated.
What’s the Best Temperature for Your Water Heater?
You probably don’t give your water heater much thought till you’re in the middle of a shower and the hot water stops working. It might be much more dangerous if the water is overly hot and causes scorching. Although you have the ability to modify the temperature of your water heater, should you? Even while you would believe that water heaters have a standard suggested temperature, this is not the case. Some water heater manufacturers factory-set their water heaters at 120°F (49°C), while others factory-set their water heaters at a default temperature of 140°F (60°C).
The Occupational Safety and Health Administration (OSHA) advises that the temperature be maintained at or above 122 degrees to assist avoid the formation of potentially dangerous microorganisms in the workplace.
Should I Change the Water Heater Temperature?
For the purpose of determining the most appropriate water heater temperature for your house, there are various elements to take into consideration.
Hot Water Kills Harmful Pathogens
A health problem arises when Legionella, the bacterium that causes Legionnaires’ disease, develops in the water systems of residential properties. According to the Occupational Safety and Health Administration, water heaters that are kept below 140 degrees and that include scale and silt may promote Legionella growth. Fortunately, the vast majority of healthy persons who are exposed to Legionella do not become ill. However, before you decide to turn up the temperature dial on your water heater, consider the following.
Hot Water Can Scald
The use of hot tap water is a leading cause of burn injuries and fatalities. Scald burns can be a serious threat in the house, especially if you have young children or elderly people living with you. Young children, because their skin is thinner, and the elderly, because their skin might be less sensitive to warmth and may be slower to respond to scalding water, are the two age categories that are most at risk for scalds. Adults may suffer third-degree burns if they are exposed to 150-degree water for even a brief period of time (as little as two seconds), according to the Consumer Product Safety Commission.
Though the temperature reaches 120 degrees, a five-minute exposure might result in third-degree burns even if the temperature is lower.
Minimize Risk with Anti-Scald Devices
The leading cause of burn injuries and deaths is hot tap water. It is extremely dangerous to have young children or elderly people in the house if you have a history of scald burns. Young children, because their skin is thinner, and the elderly, because their skin might be less sensitive to warmth and may be slower to respond to scalding water, are the two age categories that are most at risk for scalds: Adults may suffer third-degree burns if they are exposed to 150-degree water for even a brief period of time (as little as two seconds), according to the Consumer Products Safety Commission (CPSC).
In addition, burns can result with a six-second exposure to 140-degree water or a 30-second exposure to 130-degree water. If the temperature is 120 degrees, a five-minute exposure might result in third-degree burns even if the temperature is 120 degrees.
Will Changing the Water Heater Temperature Save Money?
The temperature at which you set your water heater can make a significant impact in the amount of electricity your home consumes. It is estimated that the water heater accounts for between 17 and more than 25 percent of your monthly energy bills, making it one of the most expensive single items on your home energy bill. Turning down your water heater temperature, according to the Energy Department, results in a considerable reduction in the expenses of standby losses, which are heat losses from your water heater into the surrounding region.
Reduced temperatures can result in more savings when doing duties such as washing clothing, taking showers, and dishwashing, among others.
What is My Water Heater Temperature?
You won’t be able to identify the temperature of most tank water heaters and some tankless water heaters merely by glancing at the temperature dial, because most are simply designated from “Low” to “Hot” (or “Very Hot”) on the dial. It is recommended that you consult your water heater’s handbook for the preset temperature. If you don’t know what you’re looking for, simply search the internet for the brand and kind of water heater you have, as well as the “default temperature.” However, the default temperature of the water heater is not always the same as the temperature of the water that is flowing out of your faucets.
How to Check Your Tap Water Temperature
- Avoid using your hot water for at least two hours before doing the test. If you have a tankless water heater, you can skip this step
- Otherwise, proceed as directed. Allow for a minimum of three minutes of running hot water. Make sure the temperature is correct by using a candy, meat, or water thermometer
- Set the temperature on your water heater’s thermostat to a more comfortable level. Continually repeat steps 2 and 3 until you get the required temperature. Wait for a full day to enable the water temperature to fluctuate before testing it once more. If you have a tankless water heater, you may skip this step.
You should wait at least two hours before testing your hot water. It is possible to skip this step if you have a tankless water heater; Allow for at least three minutes of continuous hot water flow. Use a candy, meat, or water thermometer to check the temperature. The thermostat on your water heater should be set to a higher setting. Repeat steps 2 and 3 until the required temperature is reached. Test the water temperature again after a full day has passed to enable the temperature to fluctuate naturally.
Find the Right Water Heater Temperature
Your water heater’s “optimal” temperature is essentially a matter of personal preference – for your own level of comfort, any potential safety problems, your monthly utility cost, and energy efficiency considerations.
Home Warranty Coverage for Water Heaters
Maintenance of your water heater on a regular basis can assist to prevent malfunctions and may even help to increase the lifespan of the equipment. In certain cases, even the most attentive maintenance will not be enough to avoid the onset of a problem with your water heater. When equipment such as your water heater quit operating, a home warranty can protect your budget from unexpected repair or replacement expenditures that may add up quickly. See what additional appliances and home systems you can protect with a home warranty plan, or request a quotation right away.
Should You Adjust Your Water Heater Temperature?
Most houses have a water heater, which is one of their largest energy consumers. If you’re searching for ways to reduce your energy consumption, this is a smart place to start. Prior to decreasing the temperature of your water heater’s thermostat by a few degrees, there are a few things you should consider. If you set the temperature too low, you run the risk of turning your water heater into a breeding ground for potentially harmful germs. If you set it too high, you run the risk of causing a scorching mishap to yourself or someone else.
- The quick answer is: 120 degrees Fahrenheit (degrees Celsius).
- At this temperature, dangerous microorganisms such as the kind that causes Legionnaires’ disease are stopped from proliferating and may even be eliminated entirely.
- As a result, other organizations such as the Occupational Safety and Health Administration (OSHA) suggest that the temperature of the water heater be maintained at 140 degrees Fahrenheit.
- Choosing a temperature closer to 140 degrees Fahrenheit is preferable, especially if anyone in the household has a weakened immune system.
- What Is the Deal with Scalding?
- You’ll never know when the scorching water will hit you since it takes several seconds for hot water to travel through your pipes and reach your faucet or showerhead.
- There is a remedy to the tug-of-war that exists between pathogenic safety and scalding safety: anti-scald valves are available.
- Installing an anti-scald valve may be a simple do-it-yourself operation for an experienced amateur plumber, but the difficulty of the task is determined by the configuration of the plumbing system.
- What, however, is the state of energy efficiency?
Saving energy and money is vital, but it isn’t nearly as important as protecting yourself and your family from potentially life-threatening diseases. Having said that, it is feasible to reduce expenses without relying on your water heater’s thermostat to do this:
- Reduce the amount of hot water you use. Shower for shorter periods of time and use the dishwasher instead of hand cleaning, which often consumes more water. Insulate your hot water heater as well as the lines that supply it. There are pre-cut pieces of insulation that are simple to install and can be completed in an afternoon, making this a do-it-yourself job for the weekend. It’s time to replace your water heater. It is estimated that the average water heater will survive 8 to 12 years if it is properly maintained. Water heaters that are outdated or in need of maintenance may be significantly less efficient than they were on the day they were installed. Choose a replacement that complies with the voluntary energy efficiency requirements set by theENERGY STARprogram while buying.
Considering installing some anti-scald valves or purchasing a new water heater? Get in touch with your local Benjamin Franklin right away. Call us today at (800) 259-7705 to learn more!
What Is The Ideal Temperature For Water Heaters?
The water heater in your house is the second greatest energy consumer in your home, accounting for around 18 percent of your monthly energy cost. Making certain that your hot water heater is set to the appropriate temperature will not only help you save money on your monthly energy bills, but it will also help you extend the life of the unit as well. A simple test performed within your house will assist you in determining whether or not you should check the temperature of the unit. Turn on a faucet that only has hot water coming out of it.
- Is it too hot for you to wash your hands or take a bath?
- If the water never becomes warm, it is possible that the temperature is set too low.
- A surprising amount of people are unaware that lowering the temperature on their air conditioning unit too low can be just as harmful as setting it too high.
- A tank that is kept at a too-cold temperature can encourage the growth of germs.
- The amount of elements in your home will influence whether or not you should set your unit to a temperature greater than 120°.
- Depending on whether or not the water heats up sufficiently, the following factors may influence how high you should set your gauge:
- Each month, your home’s water heater consumes around 18 percent of its total energy consumption, ranking it as the second highest source of energy use. Making certain that your hot water heater is set to the appropriate temperature will not only help you save money on your monthly energy bills, but it will also help you extend the life of the unit as well. You can determine whether or not you need to monitor the temperature of the unit by doing a simple test within your house. To use only hot water, turn on a faucet. Allow the water to heat up as much as possible before using it again. It is too hot to wash your hands or take a bath, isn’t it? Your water heater’s temperature may be set too high if you find yourself in this situation. The temperature of the water may be set too low if it never becomes warm. A Water Heater’s Optimum Operating Temperature Water heaters should be set at 120 degrees Fahrenheit, however depending on your home, this may not be the most efficient setting. A surprising amount of people are unaware that lowering the thermostat on their air conditioning unit too low can be just as harmful as setting it to a high range. Setting the water heater below 120 degrees Fahrenheit will ensure that cold showers are the least of your concerns. In the tank, germs will thrive if the temperature is kept too chilly. Legionella thrives in stagnant, chilly water, and it can produce a severe flu-like sickness if the water becomes stagnant and cool. When deciding whether or not to set your unit higher than 120 degrees, consider the amount of factors in your house. Thermal Factors in a Water Heating System The recommended 120-degree setting should be tried first. Following are some factors that may influence how high you should set your gauge if the water doesn’t heat up quickly enough:
If any of the following apply, putting the hot water heater between 120 and 140 degrees should be considered:
- A large family necessitates higher water use. The water that comes out of the dishwasher does not pre-heat
- A resident at home has a weaker immune system or is suffering from a respiratory ailment.
Hot water heaters can help you save money on energy. It is estimated that simply lowering the temperature of your hot water heater by 10 degrees, you would save three to five percent on your monthly energy bills. If you have recently acquired a hot water heater or have recently moved into a new house, double-check the settings. A temperature of 140 degrees is usually chosen as the default by most manufacturers, which may be too hot for certain houses. You may ascertain the temperature of the water by taking a reading from the water coming from the faucet or by looking at the gauge on the device.
When you turn on the hot water valve, the booster mixes the hot water with the chilly water from the input valve to provide you with a pleasant water flow.
Large families might benefit considerably from the system, which circulates hot water throughout the plumbing system so that it does not have time to chill before reaching the faucets.
Try out several temperature settings to find the one that works best for your house. Alternatively, if you believe the temperature is not adjusting effectively, contact a plumber who specializes in water heater problems.
What temperature is right for your water here?
When it comes to conserving energy at home, one of the first things that comes to mind is most likely changing the thermostat settings on your home heating system to the lowest possible level. Nevertheless, what about the temperature control device on your water heating system? The factory default setting on most water heaters supplied today is 140 degrees, and sometimes even higher – a temperature that is high enough to induce scorching but not high enough to meet the needs of most people (there are exceptions to this, however, as we will see).
However, the most compelling reason to lower your water temperature is to save electricity (and, consequently, money).
When you adjust your water heater’s thermostat to 120 degrees Fahrenheit rather than 140 degrees Fahrenheit, you’ll save around $50 per year in standing heat loss and more than $400 per year in fuel use.
A 140° setting is right in certain circumstances
However, while the majority of individuals can get by with a 120-degree setting, there are some situations in which a 140-degree setting is more appropriate. For example, if you have a member of your family who has a compromised immune system or chronic respiratory condition, a 140-degree setting is suggested to avoid Legionnaires’ disease and other water-borne illnesses. Additionally, if your dishwasher does not pre-heat the water, you may want to keep the temperature at a higher setting.
Checking your water heater thermostat temperature
This video from the United States Department of Energy will help you determine what temperature your hot water heater is set at and how to modify it. For any more assistance, please contact us and we will lead you through the process step by step. In the event that your water heater is having difficulty maintaining its temperature, or if you’re experiencing other water heater difficulties such as strange noises, a sulfur smell, or sediment buildup, please call us immediately. Repair and replacement of water heaters are available throughout western Massachusetts, and we can provide you with a FREE quote on a water heater upgrade for your house.
For additional information, please contact us immediately!
What Is The BEST Water Heater Temperature Setting?
Please keep in mind that this content may contain affiliate links. This means that, at no additional cost to you, we may gain a small profit on purchases made via our links.
If you have already set the temperature and are thinking to yourself, “I don’t have any hot water,” or “I don’t have enough hot water,” there are a few variables that might be causing the problem. If all else fails, it’s possible that the heating element is faulty and has to be replaced.
How To Check Your Water Heater Temperature
The majority of water heaters do not have a temperature gauge with a digital readout on them. Temperatures or heating ranges are marked on thethermostat, rather than numbers. A cup and a culinary thermometer will be required in order to correctly determine the temperature of the hot water heater. If you haven’t used your water heater in at least one hour, turn on the faucet that is nearest to it. Allow the water to run for at least one minute to ensure that the water is at its warmest possible temperature before filling the cup with it.
Recommended Temperature Settings
Water heaters are pre-programmed to operate at OSHA-recommended temperatures, which are around 140 degrees. The Environmental Protection Agency, on the other hand, recommends lowering the thermostat down to 120 degrees Fahrenheit to save power use and using a booster heater to attain sanitizing temperatures at certain outlets. Another point of view is that lower temperatures are preferable for homes with little children, although higher temperatures are more effective in cleaning and sanitizing surfaces.
However, the temperature is low enough to avoid scorching while being high enough to destroy hazardous microorganisms.
How To Turn Up Your Water Heater
If you are dissatisfied with the suggested temperature of your hot water heater, you may alter the settings to receive extra hot water. Although electric water heaters may require a screwdriver and potentially a tiny wrench or socket, most hot water heater settings are straightforward to modify. Keep in mind that the thermostat is factory configured to a recommended temperature, and that altering the setting may increase the risk of significant burns from the appliance.
How to Set Temperature on a Gas Water Heater
In case you are dissatisfied with the suggested temperature of your hot water heater, you may alter the settings to receive extra hot water. Although electric water heaters may require a screwdriver and possibly a tiny wrench or socket, the settings for gas water heaters are simple to alter. Always keep in mind that the thermostat is factory configured to a suitable temperature, and that adjusting it may increase the likelihood of catastrophic burns.
- Warm = 80-90°
- Low = 80-90°
- Hot (or triangle symbol) = 120°
- A= 130°
- B= 140°
- C= 150°
- Very Hot = 160°
- High = 120°
There is a “Vacation” setting that appears from time to time. This does not heat the water, but it does ensure that the pilot light remains lit.
How to Set Temperature on an Electric Water Heater
Turn off the circuit breaker if necessary. Remove the access panels from the room. Under the insulation, look for the thermostat adjustment screwhole. Adjust the thermostat control to the appropriate temperature by using a straight screwdriver to make the adjustment. After replacing the insulation and panels, the power should be restored. Here’s a good video that demonstrates the procedure:
Factors That Affect Water Temperature
Some of the things that may influence the temperature of your hot water include the distance between the water heater and the outlet, the way the pipes are built, and the quality of the heating element itself, among others. Because of the length of the pipe and the small bore size, it will take longer for the hot water to reach the opening. Additionally, pipes that run beneath or outside the residence may be exposed to freezing or freezing temperatures in the winter and summer. Installing a hot water recirculation system in a large house may be worth considering since it can reduce the amount of time it takes to heat water in all of the property’s outlets while also resulting in significant cost savings over the long term.
If setting the thermostat does not result in the desired temperature, it is possible that the water heater element has to be replaced. If you don’t notice a difference in the water temperature after adjusting the thermostat, it’s likely that the thermostat is broken and has to be replaced.
How to Adjust Your Water Heater’s Temperature
It has been shown that even ordinary tap water might be hazardous. Every year, a number of individuals (mainly youngsters) are sent to hospitals after suffering burns as a result of water heaters that have been set excessively high. But what exactly does “too high” imply, and how can people ensure that their water heaters are set at a temperature that will not cause them to be burned, is a mystery. The Environmental Protection Agency (EPA) recommends a hot temperature setting of 120 degrees Fahrenheit for both safety and energy savings reasons.
Use this procedure if the stickers on the water heater do not inform you how to set the temperature and you are unable to locate the owner’s handbook.
- Make sure to run hot water for at least three minutes from the faucet nearest to the water heater. Fill a glass with hot water and check the temperature
- If the water temperature is higher than 120 degrees, adjust the dial, wait approximately three hours, and then check again. Continue until the water reaches 120 degrees Fahrenheit.
The temperature of the water heater should be checked the next morning before anyone uses any hot water as a last check. Once you have found the perfect setting, make a note of it on the dial so that you do not have to go through the testing procedure again. Here are some more suggestions for extending the life of your water heater.
The next morning, before anybody uses any hot water, check the temperature of the water heater as a last check. Once you have determined the proper setting, make a note of it on the dial so that you do not have to go through the testing procedure again. Other methods of extending the life of your water heater are listed below:
The argument for 120 degrees
As recommended by the United States Department of Energy and the American Society of Sanitary Engineering, the best temperature to set for a hot water heater should be 120 degrees Fahrenheit. The following are some advantages:
- It is more beneficial to the environment. Not only does it need electrical or gas energy to heat your water, but it also takes energy to keep the water in the storage tank at that temperature (so you have hot water on demand). By lowering the temperature by 20 degrees, you may dramatically reduce the amount of energy consumed, resulting in significant savings. The energy savings are beneficial not just to the environment, but also to your money, with the potential to save you up to $60 per year. It also helps to avoid mineral accumulation. Using cooler water means that minerals are less likely to be deposited in your pipes, reducing the troubles caused by hard water and keeping your water flow unimpeded
- It also helps to prevent severe scalding. This is, without a doubt, the most compelling of the arguments. Water that is 140 degrees as it comes out of the faucet can cause significant burns in as little as two or three seconds. When exposed to 120 degree water, on the other hand, it takes only a minute or two for the skin to begin to burn. The skin of young children and the elderly is more vulnerable to burns than that of other individuals, and scorching can be fatal for them.
The argument for 140 degrees
Why would anybody propose cooking at a higher temperature when there is a danger of scalding? Actually, another federal organization, the Occupational Safety and Health Administration, or OSHA, has determined that 140 degrees is a safer temperature to work at. The most pressing worry is the elimination of a certain strain of bacteria from the environment. The majority of homes will not have to be concerned about this because water heated to 120 degrees will kill the vast majority of common germs.
Older water systems with rusted pipes, as well as a water storage system that enables water to stagnate outdoors or for extended periods of time, are all potential risk factors for LDB bacteria growth.
Which should you choose?
The majority of houses can safely reduce the thermostat to 120 degrees Fahrenheit. If you live with children or elderly relatives, the risk of scalding is far greater than the risk of contracting a rare type of germs. When your water supply has been alerted that it is susceptible to LDB bacteria, or if you have an older system with stagnant water, you should raise the temperature of your water. If you have a delicate or weakened immune system, it’s particularly crucial to keep your body temperature higher than normal.
You may also consider purchasing a tankless water heater, which warms water only when it is required and does not require a storage tank.
If you aren’t yet in the market for a new water heater, insulating your existing heater and pipes may help you save money on your energy bills as well. If you choose any temperature setting, you will save money!
Changing the temperature on your water heater
Once you’ve determined which temperature is best for your home, you’ll need to figure out how to make the adjustment. To begin, ascertain the temperature at which your water is now running. This step is as simple as allowing the hot water from your faucet to run for a few minutes, filling a glass, and using a kitchen thermometer to check the temperature of the water. If you decide that you need to modify the temperature, you may need to reference the owner’s handbook for your water heater to see where the temperature setting is located.
If you have any difficulties changing your water heater’s settings, or if you detect a leak or another problem, a technician from Ken’s would be happy to assist you with your situation.
Plumbing Hacks, Bathroom, and Water Heaters are some of the topics covered.
How to adjust your water heater temperature
No one enjoys taking a cold shower. It’s much worse when you are scalded when the hot water is turned on. It is critical to correctly regulate the temperature on your water heater, not only for your health and safety, but also to save money on your power bill. Here’s how to regulate the temperature of your water heater to save money while also protecting your skin from sun damage.
The correct temperature range
It is recommended that your water heater be set within a specified temperature range for a variety of different reasons. A low temperature setting not only results in hot water that is merely lukewarm at best, but it can also promote bacterial development, which can lead to illnesses such as Legionnaires’ disease. This may be avoided by adjusting the temperature of the water heater to a level at which the bacteria Legionella cannot survive. A temperature of at least 140 degrees Fahrenheit (60 degrees Celsius) for water heaters is recommended by the Occupational Safety and Health Administration (OSHA) to prevent Legionella and other germs from growing in the water.
- The time it takes for third-degree burns to occur at 150 degrees Fahrenheit (66 degrees Celsius) is less than two seconds.
- Not to mention that a water heater that is set too hot might result in an excessively expensive power bill.
- The greater the distance between a faucet and the water heater, the greater the amount of heat that will be lost as the water flows, especially if the pipes are not insulated.
- When determining the appropriate temperature for your family and household, use your best judgment.
Make an adjustment, test it, and continue the process until you’ve found the ideal temperature setting for your house and water heater, which may take many attempts. Currently playing: Keep an eye out for this: Take a look inside the CNET Guide to Smart Living. 1:00
Adjusting water heater temperature
The interface used to control the temperature of a water heater will differ depending on the kind and model. Fortunately, the majority of water heater models can be modified in the same way. For example, most contemporary gas and electric water heaters are equipped with a thermostat concealed behind an insulated access panel. Electric water heaters are frequently equipped with two thermostats: one at the top of the tank and another at the bottom. Furthermore, most tankless water heaters include a display with a temperature reading as well as controls for altering the water heater’s temperature.
Turn on the water in the bathroom or kitchen sink and let it to run until the water is completely hot before using.
The process of adjusting a tankless water heater is quite similar to the process of adjusting your air conditioning thermostat. Adjust the temperature by using the digital control panel, which may be adjusted up or down as desired.
Gas or electric water heaters
Some gas water heaters include a dial towards the bottom of the device that may be adjusted simply by turning it – no tools are required for this operation. Nonetheless, most current tank water heaters (whether gas or electric) require a bit more effort, but the process is still straightforward and should only take a few minutes.
- Turning off the water heater’s electricity at the circuit breaker is the first step. To remove a thermostat(s), locate the access panel for the thermostat(s) and remove it using a screwdriver
- Remove the insulation by peeling it back. To adjust the thermostat, use a flathead screwdriver to turn it up or down.
- If your water heater has two thermostats, make sure they are both set to the same temperature. The temperature on the top thermostat should be a few degrees higher than on the bottom thermostat.
The thermostats on your water heater should be adjusted by the same amount if your water heater has two of them. There should be a slight difference in temperature between the top and the bottom thermostats. If your water heater has two thermostats, set them both to the same temperature setting. The temperature on the top thermostat should be a few degrees higher than on the bottom thermostat;