How to Maintain a Tankless Water Heater
Article in PDF format Article in PDF format In the course of time, minerals can accumulate in a tankless water heater’s heating chamber, where they can build up and damage the walls of the tank’s heating chamber. You must flush and remove the mineral deposits from your tankless water heater’s tank at least once every year in order to keep it in proper working order and cleanliness. Continue reading to find out how to properly maintain your tankless water heater in order to guarantee that it operates at peak performance and energy efficiency.
StepsDownload Article
- Article in PDF Format Article in PDF Format In the course of time, minerals can accumulate in a tankless water heater’s heating chamber, where they can pile up and damage the walls. You must flush and remove the mineral deposits from your tankless water heater at least once every year in order to properly maintain and clean it. Follow the steps outlined in this article to guarantee that your tankless water heater operates at peak performance and efficiency.
- This can be accomplished by shutting down the main gas line or turning off the circuit breaker for electrical appliances.
- Secondly, shut down and switch off the three water valves connected to your tankless water heater.
- Secondly, shut down and switch off the three water valves connected to your tankless water heater
- Advertisement
- s3 Take care not to damage the purge port valve caps when you remove them from the purge valves on each of the cold and hot water valves
- The purge valves are distinguished by their little handles that mimic the letter “T.” In order to alleviate any pressure that has built up inside the valves, this technique must be performed in order to prevent excessive hot water from flying out and coming into touch with your skin. Due to the possibility of pressure build-up when removing the purge port valve covers, it is critical to ensure that the hot water valve is completely and correctly switched off for safety reasons. Using gentle pressure, gently tighten each cap to ensure the rubber washer sealing discs remain in place, which are required for your valves to operate correctly.
- Fourth, connect your hosing lines to each of the three valves.
- Fourth, connect your hosing lines to each of the three valves
- Opening the purge port valves by twisting them in the opposite direction of the cold and hot valves is a good way to start the process. 6 Instead of using chemical solutions to clean your tankless water heater, have 2.5 gallons (9.46 liters) of undiluted white vinegar on hand at all times.
- In addition, because your tankless water heater is most likely the source of all of your drinking and bathing water, employing chemical cleaning solutions might have a negative impact on the quality of your water.
- 7 Follow the manufacturer’s instructions for the flushing and draining of your tankless water heater to the letter to complete the operation.
- 8After the flushing operation has been finished, close the purge port valves by twisting the “T”-shaped handles. Remove the hosing lines from each water valve by disconnecting and removing them. Tenth, attach the purge port valve covers to the purge valves
- And eleventh
- Make sure to tighten the caps completely and firmly without damaging the rubber sealing discs that are placed within the caps.
- For specific information on how to properly re-start your tankless water heater, consult the manufacturer’s handbook.
- If all that is required is for you to rotate and open the cold and hot water valves so that they are parallel to the position of the main valve that leads into the home, you have completed the operation.
- Alternatively, slowly turn on the hot water tap in your sink to allow air to travel through the pipe.
- Continue to run the water until it is running consistently and there is no air escaping from it
- It is possible that this operation will take up to 2 or 3 minutes.
Create a new question
- Question What should I do if there is a leak in the plumbing and steam is escaping while the hot water is being used? Your heat exchanger has developed a crack and will require replacement. You can purchase only that component or you can replace the entire tankless heater. Even though replacing a single component is less expensive (in terms of components), I chose to replace the entire unit because the water had seeped into the electronics, and who knows when that might cause another failure
- Question Is it necessary to perform this procedure even if I have a water softener? Yes, since it’s critical to keep a tankless water heater in good working order. The heating components get very hot, causing calcium and other deposits to bake onto the heating units in a short period of time. Even if the water is from a clean municipal source, it should be filtered. A tankless heater’s life duration is significantly reduced if it is not properly maintained. They’re a highly delicate piece of machinery that requires constant attention and maintenance. Install a filter before the heater and clean it twice a year to ensure that it has a long service life. It is absolutely necessary. You’re more concerned with removing baked-on crap from the heating element than with clearing off dirt or debris. Question How long can I keep and reuse white vinegar after cleansing a Rinnai tankless water heater with it? Can I store and utilize the vinegar again? No, because the utilized vinegar contains dissolved particulates, it is no longer considered “virgin.” Always discard the old vinegar and replace it with new vinegar before flushing the toilet.
More information can be found in the following answers: Advertisement
Video
- Make sure you have all of the tools and equipment necessary to flush and drain your tankless water heater by consulting the manufacturer’s instructions for your particular model of tankless water heater.
Thank you for submitting a suggestion for consideration! Advertisement
- Your suggestion has been received and will be considered. Advertisement
Advertisement
Things You’ll Need
- Advertisement
About This Article
The writers of this page have together authored a page that has been read 222,267 times.
Did this article help you?
Tankless hot water heaters are ideal for consumers who wish to save on energy costs while still having access to hot water on demand. The fact that they are small in size means that they are soon becoming the most popular choice for water heaters in both residential and commercial settings. If you have a tankless hot water heater, it is critical that you do regular water heater maintenance on it. Maintaining your water heater on a regular basis might extend its lifespan to more than twenty years.
Tankless Hot Water Heater Maintenance should be performed twice a year if you live in a region with hard water or if you have the water temperature set to a high setting on your tankless water heater.
Several tasks will need to be completed as part of the routine maintenance.
Flushing the System
Those looking for energy economy as well as hot water on demand would appreciate tankless water heaters. As a result of their small size, they are fast becoming the most popular choice for water heaters in both residential and commercial settings. Performing adequate water heater maintenance on your tankless hot water heater is critical if you own a tankless heater. Maintaining your water heater on a regular basis can help it last for more than 20 years. A hot water heater should be maintained at least once a year to ensure that it is operating at peak efficiency.
In this way, you can confirm that all of the heater’s components are functioning properly.
Cleaning the Air Filter
Tankless hot water heaters are ideal for consumers who wish to save money on electricity while still having access to hot water on demand. They are small in size and are increasingly becoming the most popular choice for water heaters in both residential and commercial settings. If you possess a tankless hot water heater, it is critical that you do regular water heater maintenance on it. Maintaining your water heater on a regular basis can help it last for more than twenty years. A hot water heater should be maintained at least once a year in order to ensure proper operation.
This will aid in ensuring that all of the heater’s components function as they should. Several tasks will need to be completed throughout the maintenance period.
Cleaning the Water Filter
It is critical that you do not overlook the water filter while doing water heater maintenance on your unit. The majority of tankless water heaters are equipped with a screen that helps to collect any silt that may enter the system. You will need to remove these particles from your water heater on a regular basis in order to keep it operating at optimal performance. If sediment builds up in your hot water heater, it can significantly impair its ability to perform properly. The hot water heater’s water supply must be shut down before you can remove the filter from the system.
It is possible to clean it with warm soapy water or by wiping it down with a towel If you are unable to locate your water filter, consult your user handbook to identify where it is located.
Cleaning the Tank
Occasionally wiping down the outside of the tank is advisable to ensure that no dust or dirt accumulates on it. Make sure to turn off the electricity and water supplies before you begin. Using a damp cloth, wipe off the tank and the surrounding area. It is possible for a buildup of dust and debris to get inside the water heater, which can create problems. Tankless Water Heater Maintenance should be performed on a regular basis to guarantee that your unit is operating as it should. When performing heater maintenance, make sure to inspect all of the other components of the heater.
Look for any leaks, corrosion, or anything else that appears to be wrong.
The longer you let a problem to fester, the worse it can develop and the more expensive it can become.
Tankless hot water heaters are their specialty, and they have years of expertise with them.
Do Tankless Water Heaters Need Maintenance?
Please keep in mind that this content may contain affiliate links. This means that, at no additional cost to you, we may gain a small profit on purchases made via our links. It is necessary to repair all mechanical devices and equipment on a regular basis in order to ensure maximum durability and efficiency, and a tankless water heater is no exception. Being aware of why it’s vital and what has to be done might assist you in making preparations for this procedure.
Common Issues With Tankless Water Heaters
It is possible to reduce downtime due to repair concerns by keeping your tankless hot water heater in good condition. Moreover, it has the ability to increase the longevity of your unit and boost energy efficiency over the course of several months or years. Water hardness is one of the most major elements that might cause system failure and require repairs, although regular system maintenance can mitigate the impact of hard water on the system. Hard water contains a high concentration of minerals, and these minerals can cause scaling and other problems inside your system.
Consider that every tap water that passes through your system contains at the very least minimal amounts of minerals that can accumulate over time. Also see: Condensing vs. Non-Condensing Tankless Water Heaters for more information.
How Tankless Water Heater Maintenance Helps
When it comes to dealing with maintenance, you have two options: schedule service or do it yourself. Generally speaking, the most common form of maintenance service required for most of these systems related to cleaning the system in a variety of ways. Minerals that have caked onto the components of the unit must be removed by descaling procedures. Installing an inline filter is a wise investment if you want to significantly decrease accumulation. A general cleaning, on the other hand, is good.
Additionally, by following these instructions, you may be able to prevent needless wear and strain on your unit, which may allow it to last longer.
Descaling Process
The need for descaling may arise from time to time if you reside in a location where the water is hard. Descaling is the procedure that entails eliminating the muck that has built within your system over time. Your system might become clogged with minerals from the water, causing a thick build-up of sediment. The descaling procedure is quite similar to the flushing and cleaning procedure described below. a. Running a substantial volume of water vinegar through the tank is required, while this is not mandatory.
Keep in mind that, after using vinegar for demineralization, you may need to rinse or flush the system for up to 45 minutes in order to completely eliminate all vinegar and debris from the unit.
- Rheem
- Rinnai
- Navien
- Noritz (which generally corrects Noritz fault codes 16 and 20)
Here’s a good video that demonstrates the procedure:
Flushing the System
Regardless of the amount of hardness in your water, all tanks should be cleaned on a regular basis. The procedure is a little more difficult than flushing a storage tank water heater, but it is still rather simple. This treatment is often performed every 6 to 12 months, with the frequency ranging between 6 and 12 months in many circumstances. It is necessary to follow the manufacturer’s directions during the flushing procedure. How to Flush a Tankless Water Heater is a related article (Step-by-Step) A typical procedure involves turning off the water heater’s power and water supply, connecting a short hose to each of its isolation valves, connecting a small pump to the end of its cold water hose, and then placing the hot water hose and circulation pumpinlet hose into an empty 5-gallon bucket of water.
The power of the water flowing through the system will aid in cleaning the system and may also assist to eliminate any minerals that have accumulated in the unit over time.
When to Perform or Schedule Service
Now that you understand the necessity of maintaining your tankless water heater as well as the actions that must be taken, you must select how frequently you will conduct the maintenance. More than that, you must determine if you will do it yourself or hire a professional to do it for you. While these fundamental procedures appear to be straightforward to execute, you must first grasp which valves control which components of the machine before you can begin playing with it. Furthermore, you want to be certain that your efforts are effective in cleaning the system.
If you have a tankless water heater, the plumber may notify you of the suggested frequency for performing maintenance services on it in the future.
Furthermore, the cost of repairing a problem is nearly always higher than the cost of performing preventative maintenance.
While you won’t be able to avoid all sorts of problems from arising, you will be at a considerably reduced chance of experiencing one. It is possible to discover more about the exact maintenance methods necessary for your particular model by going through the product handbook.
9 Helpful Tips for Tankless Water Heater Cleaning and Maintanence
Previous PostNext PostHot water at your fingertips! One of the advantages of installing a tankless water heater is that it saves space. Another advantage of a tank water heater is the potential for energy savings of up to 50% over a normal tank water heater. In the same way that any other household appliance performs more effectively with proper maintenance, your water heater will work more efficiently with proper care as well. The first step is to do routine maintenance! Read today’s post for six suggestions on how to clean a tankless water heater and perform other essential maintenance activities.
You might even be able to extend its usable life!
1. How Often Should You Clean a Water Heater?
Whatever your experience level with tankless water heaters is, whether you’re a new convert or have had your unit for several years, you’ve probably had queries about how often you should clean the unit. The majority of water heater manufacturers recommend cleaning your water heater once a year. To be sure, the frequency may vary depending on your location and the quality of your drinking water. In the case of hard water, you may need to cleanse your water heater more frequently than in other circumstances.
Residents in all cities are provided with monthly or quarterly updates on the state of municipal water systems by city staff.
Concerning the cleaning of the unit’s outside, we’ll get to it in a minute.
2. Taking Care of Exterior Maintenance
The majority of homeowners take pleasure in performing at least a few house maintenance tasks themselves. In order to ease into water heater maintenance if you are new to the game, taking care of the outside of your water heater is a good first step. Exterior upkeep does not necessitate the expenditure of a significant amount of time or resources. Begin by wiping down the cover of the book. Using a non-abrasive cleanser and a soft cloth to clean the device helps to maintain it clear of dust and avoid the formation of rust.
- Checking pipes during cold weather is important for our northern neighbors to avoid frozen pipes.
- Finally, if your tankless water heater is equipped with a pressure release valve, you should make sure it is working properly.
- If you have any questions concerning your water heater, you should consult with a plumber.
- The process of flushing the water heater will take a bit more time.
3. Why You Should Flush
Water heaters, like other appliances, accumulate limescale deposits over time. Failure to descale conventional tank models can result in an explosion in some instances. Tankless water heaters will not explode, but if the sediment is not flushed out of the unit, it may cause the heat exchanger to work harder than it needs to, increasing the risk of failure. The ability to keep sediment washed out not only allows the water heater to operate more effectively, but it can also assist prevent additional issues.
Consider an isolation valve to be similar to the shut-off valve on a normal tank water heater in terms of function.
It is possible that your water heater does not have an isolation valve. If it doesn’t, you might want to consider having a plumber install one. When doing maintenance, the absence of an isolation valve might pose a serious safety threat.
4. What Supplies Do You Need to Clean the Water Heater?
We’ve covered safety; now it’s time to speak about the supplies you’ll need to flush the unit. These are the materials you’ll need: While you may purchase each component separately, a flush kit contains everything you need in one convenient package. Alternatively, you may use 4 gallons of undiluted white vinegar instead of the descaling solution included in the flushing package.
5. How to Descale a Tankless Water Heater
We’re presenting the simple methods for descaling a water heater since it’s one of the maintenance activities that many homeowners can complete with little or no help from a professional. The first step is to turn off the power that is feeding your water heater. Locate and close the gas isolation valve if one exists. Shut off the hot and cold water shut-off valves while you’re working on the unit to prevent water from entering the unit. If your machine is equipped with a pressure relief valve, carefully open it to relieve any built-up pressure.
- Next, put the submersible pump in the bucket you just made.
- You may either pour four gallons of vinegar into the bucket or use the descaler that came with the flush package to remove the scale.
- Allow at least an hour for the descaling solution of your choice to circulate through the hot water heater.
- Following completion of descaling, switch off the pump.
6. Final Steps for Tankless Water Heater Cleaning
Closing the cold water service port and opening the cold water shut-off valve are the next tasks you need to do. This step removes any vinegar that may have remained. Following that, you’ll close the valve and allow the water to drain completely. It is now necessary to shut the hot water port. Finally, if there is a cold water input filter, make sure to remove it as well as the hot water in-line filter before continuing. Flush both of them in the sink to ensure that any remaining sediment is removed.
Keep in mind that, while it might be a fun DIY project, you may feel more comfortable having a professional plumber complete the task.
Need to Schedule Tankless Water Heater Maintenance?
Maintenance, including tankless water heater cleaning, should be performed at least once a year to ensure that everything is running well. You may need to perform additional duties, such as cleaning off the unit’s outside, on a more frequent basis, especially if the location where the water heater is installed receives a lot of dust. While you can perform some simple maintenance on your own, why not enlist the assistance of our team?
For both tankless and traditional tank water heaters, we are delighted to plan periodic descaling and yearly service appointments with you. For a free estimate, please contact us immediately. Previous PostNext Post Previous Post
8 Steps to Maintain your Tankless Water Heater
An electric tankless water heater is one of the most energy-efficient and cost-effective ways to provide hot water for your house. Because it delivers hot water on demand, a tankless water heater system takes up less space and consumes less energy than a standard tank-style water heater system. The installation of a tankless water heater is a significant investment in your house, and they may last for up to 20 years if they are properly maintained. Tankless water heaters, like any other item in your house, require regular maintenance to ensure that they continue to function properly.
Turn off the energy source
Whenever you are doing inspection or maintenance on your tankless water heater, the very first thing you must do is switch off the electricity to the unit. The majority of tankless water heaters are powered by gas or electricity, while others are powered by kerosene or even propane. The maintenance operation is made safer by turning off the main gas outlet or the main power source at the circuit breaker before beginning.
Close all the water valves
To prevent water from entering the tankless water heater, you must close the water valves on the water supply lines. This also prevents any warm water from escaping the cleaning system during the cleaning procedure itself. To turn off the water, there are normally three color-coded water valves to use. Cold water is controlled by a blue valve, hot water is controlled by a red valve, and the third valve regulates the flow of water between the main water supply and your residence. Before commencing the maintenance procedure, be sure that all three of these valves are closed.
Disengage the purge port valve caps
Purge valves are included into your tankless water heater to aid in the control of pressure buildup. Each has a little handle that is shaped like the letter “T” on the end. When you remove the purge port valve covers, be careful not to overdo it since this can cause pressure to build up in the purge valves. This also stops hot water from spouting out, which may cause you to burn yourself.
Attach hosing line to each valve
In some cases, hosing lines may have been included with your tankless water heater; in others, you may need to purchase them from a home improvement store. Alternatively, the hosing line can be used to connect the water heater to a flushing bucket or other similar device. It is possible that you may need to connect the hoses to a sump pump. This enables the hot and cold water valves to flush through and release water from the tankless water heater unit while the device is in use. It may be beneficial to refer to the handbook that came with your particular tankless water heater model for more detailed instructions.
Open the port valves
Twist the port valves until they are perpendicular to the water valves, then release the twisting force.
Add descaling solution or white vinegar to the unit
To clean your tankless water heater, you can use a normal descaling solution or roughly 2.5 gallons of pure white vinegar.
Many households prefer vinegar over other cleaning products since it is typically believed to be safer.
Flush and drain the tankless water heater
You may next clean and drain your water heater using the directions in your owner’s handbook to ensure that everything is in working order. The water heater should be flushed and allowed to drain to the bucket for approximately 45 minutes to ensure complete cleaning. After the flushing has been done, you may close the port valves and then disconnect the hosing line from the water valves to complete the process. After that, you may gently reseal the purge valves with the port caps that came with them.
Restart the tankless water heater
Having everything in place, you may flush and drain your water heater, following the directions in your owner’s handbook for advice. The water heater should be flushed and drained to the bucket for roughly 45 minutes to ensure complete cleaning. You may then turn off the water and disconnect the hosing line from the water valves when the flushing process is complete. By carefully replacing the port caps on the purge valves, you can ensure that they are properly sealed once again.
Tankless Water Heater Service in Denver Colorado
Denver, Colorado Tankless Water Heater Repair Service A hose clamp was installed to prevent seepage from the condensate line, after which the recirculation settings were checked. The Dedicated Recirculation Mode Did Not Stay Locked In. The recirculation pump is operational, and we recommended that they continue to use Economy Mode as long as they desired, and that if they continued to have issues with recovery time or volume, we may switch to Comfort Mode. Tankless Water Heater Service in Denver, Colorado on September 26, 2018.
- Two leaks on the existing manifold have been repaired.
- It does not have a port for a thermal bypass filter.
- Maintenance and cleaning are performed on an annual basis.
- Denver, Colorado Concerning High-Pressure Situations, Make a Call Water Heater Service in Denver, Colorado on January 16, 2018 (Denver, Colorado) Code 27 has been corrected.
- Denver, Colorado Colorado Tankless Water Heater Service by Rinnai on January 6, 2017 in Denver, Colorado Rinnai R53 REUV2520FFU-US 07.07-123855 Rinnai R53 REUV2520FFU-US (91).
- In addition, the water filter was replaced.
- The temperature is 125.
Denver, Colorado on January 5, 2017.
Small Amount Of Debris Found In The Flush Unit.
Tankless Water Heater Service in Denver, Colorado on January 5, 2017.
Rinnai RL75 REUVC2528FFUD-US Rinnai RL75 REUVC2528FFUD-US Rinnai RL75 REUVC2528FFUD-US (A).
It’s a short walk to the unit.
Denver, Colorado on January 5, 2017.
Denver, Colorado on January 5, 2017.
A 5 Star rating for the Rinnai R53 in Denver on July 10, 2015.
Denver, Colorado Rinnai R85 Tankless Water Heater Service 07-10-2015 Tankless Water Heater Service Denver, Colorado The Rinnai R75 Tankless Water Heater Service in Denver, Colorado was performed on July 10, 2015.
Denver, Colorado Tankless Water Heater Service Rinnai 2520 DENVER, CO05-15-2015 Tankless Water Heater Service Denver, Colorado The Rinnai R94 Tankless Water Heater Service in Denver, Colorado was performed on May 15, 2015.
Denver, Colorado Tankless Water Heater Service Rinnai R75 DENVER, CO05-15-2015 Tankless Water Heater Service Eternal DENVER, CO05-15-2015 Tankless Water Heater Service Denver, Colorado 05-15-2015 Tankless Water Heater Service Denver, Colorado Denver, Colorado Rinnai R75 Tankless Water Heater Service on May 13, 2015.
The Rinnai R75 tankless water heater was serviced in Denver, Colorado on May 13, 2015.
Denver, Colorado Tankless Water Heater Service.
The Rinnai R94 in Denver, Colorado was serviced on May 11, 2015 by Tankless Water Heater Service Denver, Colorado. Denver, Colorado Tankless Water Heater Service Rinnai R85 DENVER, CO05-11-2015 Tankless Water Heater Service Denver, Colorado Rinnai C53 DENVER, CO, USA, November 5, 2015
Tankless Water Heater Services
Tankless Water Heater Repair in Denver, Colorado – Recirculation settings were checked, and a hose clamp was added to prevent seepage from a condensate line. There was no lock in with the dedicated recirc mode. When the recirculation pump was turned on, we advised them to keep it running in economy mode for the time being. If they continued to have problems with recovery time or volume, we suggested they try Comfort Mode. Colorado09-26-2018 Tankless Water Heater Service in Denver, Colorado. The Rinnai unit and the manifold system were tested for leaks during the leak test.
- Gas shut-off on furnace line has been re-tightened.
- Tankless Water Heater Service in Denver, Colorado on September 25, 2018.
- Tankless Water Heater Service in Denver, Colorado on April 16, 2018.
- Water Heater Service in Denver, Colorado on January 16, 2018 (Denver, CO) Code 27 was fixed.
- Denver, Colorado.
- Reuv2520FFU-US Rinnai R53 07.07-123855 R53 REUV2520FFU-US Rinnai R53 REUV2520FFU-US Rinnai R53 REUV2520FFU-US (91).
- The water filter was also replaced.
120 degrees Fahrenheit Tankless Water Heater Service in Denver, Colorado on January 5, 2017.
Rheem RTG 74PUN, serial number is 0406P001609.
Denver, Colorado Tankless Water Heater Service Rinnai RL75 REUVC2528FFUD-US RL75 REUVC2528FFUD-US RL75 REUVC2528FFUD-US RL75 REUVC2528FFUD-US (A).
Tankless Water Heater Service in Denver, Colorado on January 5, 2017.
Tankless Water Heater Service in Denver, Colorado on January 5, 2017.
7/10/2015 DENVER, CO – Rinnai R53 5 Star Rating.
Denver, Colorado Tankless Water Heater Service Rinnai R85 07-10-2015 Denver, Colorado Tankless Water Heater Service The Rinnai R75 tankless water heater was serviced in Denver, Colorado on July 10, 2015.
The Rinnai R94 tankless water heater was serviced in Denver, Colorado on May 15, 2015.
The Rinnai R98 tankless water heater was serviced in Denver, Colorado on May 15, 2015.
Tankless Water Heater Service in Denver, Colorado by Eternal on May 15, 2015.
Service on a Rinnai Tankless Water Heater in Denver, Colorado on May 13th, 2015.
R85 Tankless Water Heater Service in Denver, Colorado on May 11, 2015. Rinnai R85 Tankless Water Heater Service in Denver, Colorado on May 11, 2015. On November 5, 2015, the Rinnai C53 was delivered to Denver, Colorado.
- Scale accumulation results in decreased efficiency and capacity
- Inlet filters that are clogged or limited
- Failures of the flame to ignite on an intermittent basis due to low gas pressure
- A clogged or blocked air intake or exhaust venting
- Condensation that is not properly formed or condensation leaks Unacceptable wait times for hot water, or variations in wait times
- Variable output water temperatures are frequently caused by problems with the pressure balance. Hot water that comes on and off
- Water is not as hot as it used to be
- When the system alarm sounds or the unit runs loud or noisy, it means that something is wrong. The system must be reset on a regular basis.
A tankless water heater that has been properly installed and serviced is energy efficient, quiet, and space saving, and it produces limitless hot water. Tankless water heater problems are nearly often the result of faulty installation, poor water quality, dirt and debris, or inadequate maintenance, according to our research. Every possible tankless water heating problem has been encountered and effectively resolved by our team. Tankless systems are built with maintenance in mind, rather than replacement in mind.
Make an appointment for tankless repair.
Easy Maintenance Tips for Tankless Water Heaters w/Photos
A little ‘how-to’ information may go a long way toward ensuring that your tankless water heaters operate at peak efficiency. As a result, not only will you save money on plumbing expenses, but you will also extend the life of your tankless water heater. You may be asking yourself right now, ‘what are some tips for keeping my tankless water heater in good working order?’ Is it necessary to do periodic maintenance on tankless water heaters? Tankless water heaters, like any other type of water heater, require periodic maintenance.
- Because of hard water or the amount of hot water your household consumes, you should anticipate to do this once a year at the most.
- It is recommended that you perform this once every 3-5 years if your water is soft or if you have a water softening system installed.
- We can assist you!
- It is feasible to service and clean a tankless water heater without the assistance of a professional.
- Step-by-step instructions will be provided to make it simple to understand how to remove limescale and other mineral deposits from your plumbing system.
Do You Need to Flush Your Tankless Water Heater?
The majority of people are aware that they must flush a tank-style water heater. Most people, on the other hand, are unaware that they should also flush their tankless water heater. Yes, tankless water heaters do require flushing on a regular basis. It is necessary to flush the tankless water heater to eliminate limescale accumulation on the burners within. Typically, flushing is required every 2 to 3 years in the majority of situations. When flushing maintenance is necessary, tankless water heaters will automatically shut down and display an error code on the display.
- The number of minerals present in the water supply has an impact on the hardness of the water in the tap.
- As the water warms, the sediment separates from the water in the same way as it does in a tank-style water heater.
- These misunderstandings wind up accumulating on the burners within the tankless unit as well as on the faucet aerators.
- If you find yourself cleaning your aerators on a regular basis, it may be time to descale your tankless water heater.
- A family of two may probably get away with flushing their tankless water heater every 18 months or so, according to the experts.
Because of the installation of an in-home water softening system, you may be able to get away with cleaning your water heater once every 3-5 years. Now that you’re ready to learn more about how to manage your tankless water heater, let’s get this party going.
How to Flush and Descale a Tankless Water Heater
It is necessary to do periodic maintenance on a tankless water heater in order for it to operate properly. It is possible to flush your tankless water heater in order to clean and remove mineral deposits from the burner system by following these steps:
Supplies You Will Need:
- 5 gallon bucket, 3 gallons pure white vinegar or descaling solution, 2 clothes washer hoses, channel lock pliers, 2 clothes dryer hoses
It is possible to acquire the My PlumbingStuff – Tankless Water Heater Flushing Kit – 32-ounce at this location. User Instructions for the J.C. Whitlam FLOW32 Flow-Aide System Descaler – Zoeller 42-0007 Floor Sucker Pump – 5-Gallon Bucket – Safe to Use. This practical set comes with a 5-gallon bucket, two hoses, a descaling solution, and a sump pump, among other things.
Directions for Flushing Tankless Water Heaters:
The connections under the tankless water heater may be accessed by removing the cover on top of the unit. Some tankless types may not have a cover fitted at the time of purchase.
Step 2: Verify your tankless water heater has a flushing kit installed
If the flushing valves on your tankless water heater are not there, check to see if they have been installed. Stop what you’re doing and call a qualified plumber to install them.
Step 3: turn off the gas supply
Turn off the gas feed to the tankless water heater at the main shutoff valve. It will be necessary to switch the gasoline supply such that it is “perpendicular” to the fuel line. It is not necessary to cut off the electricity to the electric thermostat.
Step 4: Turn off the water supply
Close the cold water supply valve, which is responsible for supplying water to the tankless water heater, to prevent it from being used. Cold water is prevented from entering the unit as a result of this. Close the hot water supply valve, which is responsible for delivering hot water from the tankless water heater to the rest of the home. Shot water is prevented from entering the home as a result of this. Use this opportunity to inspect your temperature and pressure relief valve (T P valve) to confirm that it is in proper operating order.
Step 5: Open the flushing valves and connect the hoses
Remove the caps from the flushing valves and set them aside. This is important in order to relieve any pressure that has built up inside the valves. Connect the hoses to the flushing valves and tighten the connections with channel lock pliers to ensure that they are secure. Check to see that the rubber washers are properly seated in the tube to ensure a tight seal and avoid leaks. The flushing valves should be opened by rotating them 90 degrees at right angles (or perpendicular) to the existing positions of the cold and hot valves, respectively.
Step 6: Setup the bucket and sump pump
Add descaling solution or white distilled vinegar to the 5-gallon bucket until it is completely filled. Lower the sump pump into the 5-gallon bucket filled with descaling solution or distilled vinegar, and then turn on the sump pump to start the cleaning process.
Step 7: Flushing the tankless water heater
Using a descaling solution, allow the sump pump to run for 30 minutes; if using vinegar, allow the sump pump to run for 1-2 hours. Using this method, the cleaning solution will be pumped through the water heater and into the pipes to be cleaned. Completely switch off the sump pump once the job is done. Remove the hoses and pour the cleaning solution container into a trash can.
Using clean water, rinse off any residual descaling solution that may have accumulated in the bucket. Until the water running through the system is clear, you’ll need to repeat this procedure several times. When you’re finished, switch off the sump pump and throw away any residual solution.
Step 8: Finishing up and closing the system
The hosing should be removed from the flushing valves. Replacing and tightening the purge port caps properly is essential. Take care not to damage the rubber seals that are contained within the caps. If you do, you must replace them as soon as possible.
Step 9: Check the sediment filter
The sediment filter is situated on the cold water input line that feeds into the tankless water heater system. Remove the sediment filter by unscrewing it and wiping it off with a damp cloth if necessary. When you’re finished, remove the filter and replace it.
Step 10: Open the water supply to the tankless water heater
Rotate the cold water supply and hot water supply valves so that they are in line (or parallel) with the pipes before opening each of the valves.
Step 11: Turn the gas on to the tankless water heater
Rotate the cold water supply and hot water supply valves so that they are in line (or parallel) with the pipes before opening each of the valves individually.
When Should You Descale a Tankless Water Heater?
Descalement of your tankless water heater does not have a specific schedule for when it should be performed. This will be highly influenced by the hardness of the water in your location. Tankless water heaters should be descaled once a year if you live in a region with extremely hard water. You’re not sure if you have hard water or not. You may use theHealth Metric Drinking Water Test Kit for Home Tap and Well Water, which is an EPA-recognized at-home water analysis kit, to assess the quality of the water that is coming into your home from your water source.
It is recommended that you describe your tankless water heater every 3-5 years if your water is soft or if you have a water softener system installed in your home.
Clean the Air Filter
- The tankless water heater should be turned off and unplugged. Remove the front cover of the book. It is customary for the air filter to be situated at the top of the water heater. Identifying and removing the air filter will allow you to determine whether or not it is unclean. Use a soft-bristled brush and a mild dish soap and water solution to clean the air filter if necessary. Afterward, rinse it well with clean water and allow it to dry on a lint-free towel Replacing the filter and the lid, as well as plugging in the water heater and turning it on
Clean the In-line Water Filter
- To switch off the gas supply to the water heater, turn the valve so that it is perpendicular to the supply line. The cold water supply to the water heater should be turned off by twisting the valve perpendicular to the supply line. The in-line water filter should be installed at the cold-water input. Remove the filter from the cold water line by unscrewing the nut. The water filter should be cleaned under running water or with a cotton swab, as necessary. reinstall the water filter, reopen the cold-water supply valve, and reopen the gas line that supplies the water heater
How Much Does it Cost to Service a Tankless Water Heater?
Tankless water heaters may be extremely expensive to fix or maintain on a professional level. Plumbers’ rates often range from $200 to $800 each service call, depending on the location. A service price for cleaning a tankless water heater will most likely range between $300 and $400 dollars. Performing the work on your own will save you a significant amount of money in the long run.
Can I Use CLR to Clean My Tankless Water Heater?
Inexpensive professional tankless water heater repairs and maintenance are difficult to come by. A typical plumber’s price ranges from $200 to $800 per service call, depending on the circumstances. In most cases, a tankless water heater cleaning service will cost between $300 and $400. This saves you a lot of money in the long run if you can do the task yourself.
Is Cleaning a Tankless Water Heater Worth the Time and Money?
Professional tankless water heater repairs and maintenance may be very expensive. Plumbers’ rates range from $200 to $800 each service call on average. Cleaning a tankless water heater would likely cost between $300 and $400 in service fees. Performing the work yourself will save you a significant amount of money in the long term.
Final Thoughts
Maintenance and servicing a tankless water heater are relatively simple tasks that can be accomplished with the correct equipment and a little handyman expertise. Simple step-by-step instructions will allow you to safely and properly clean your unit, saving you hundreds of dollars in plumbing bills. If you want to save time and money, you may purchase a descaling kit or flushing system, which is widely accessible online and includes everything you need to thoroughly clean your unit. This kit may be reused, which allows you to save even more money in the long run.
Thank you for taking the time to read this.
DISCLAIMER: The information provided on HomeInspectionInsider.com is not intended to be professional guidance.
It is owned and operated by Hubert Miles who is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by placing advertisements and links on their websites that direct traffic to Amazon.com (hereinafter referred to as “Amazon.com” or “Amazon.com Associates Program”).
As an affiliate, HomeInspectionInsider.com participates in a variety of affiliate programs with other websites. Hubert Miles receives a commission for recommending visitors and commerce to these businesses.
Are You in Need of Tankless Water Heater Maintenance?
With the correct supplies and a little bit of ‘know-how,’ servicing and maintaining a tankless water heater may be a simple task. Simple step-by-step instructions will allow you to safely and properly clean your unit, saving you hundreds of dollars in plumbing costs. If you want to save time and money, you may purchase a descaling kit or flushing system, which is widely accessible online and includes everything you need to thoroughly clean your appliance. As a result, you will save even more money in the future by reusing this kit.
Thank you for taking the time to read my post!
Before beginning any job, it is recommended that you speak with a competent expert and check local permission requirements.
HomeInspectionInsider.com is also a participant in affiliate marketing programs with other web sites that promote home inspection services.
Scaling and Its Impact on Tankless Water Heaters
If you neglect to schedule regular maintenance on your tankless water heater, scaling will have a negative influence on its performance and might cause it to fail prematurely. Hard water is the source of this problem, and hard water is defined as water that has a high concentration of minerals. Calcium, magnesium, and, in rare situations, iron, are the most often encountered dangers in the environment. These are completely innocuous minerals to consume, yet they may cause serious damage to your plumbing system.
It is possible that scaling will have a detrimental influence on the heat exchanger component of your tankless water heater.
This component must be free of contaminants in order for water to be heated efficiently.
When Should You Schedule Tankless Water Heater Maintenance?
Annual maintenance is required for some tankless systems in order to ensure that the system continues to operate efficiently over its full lifecycle. Others, possibly in places where hard water is not a significant issue, may only require maintenance every few years or even less frequently. A skilled plumber can assist you in determining the amount of hard water in your property. It’s possible that you’ll be able to discover its presence by yourself.
You have hard water if you see a chalky white or yellow deposit around your faucets or drains. This puts your tankless water heater at risk of failure. As a matter of fact, the installation of a whole house water softener may completely eliminate the effects of hard water.
When to Replace a Tankless Water Heater
It is necessary to do yearly or semiannual maintenance on a tankless water heater, although this will not extend the life of the system. Even though a tankless system can endure for more than 20 years, you will eventually need to replace it. Fortunately, this is a rather inexpensive process. The failure of your tankless water heater might occur much sooner than this if you have neglected to do regular preventative maintenance. Make sure to get in touch with our staff so that we can assist you in avoiding premature replacement.
if you need experienced plumbing service, installs, or routine maintenance.
Put your trust in Reliance!
on Monday, May 25th, 2020, Water Heaters are categorized as follows:
Tankless Water Heater Maintenance & Flush Service In NJ
Throughout the state of New Jersey, Water Heaters NJ offers tankless water heater maintenance and flushing services. The components of your plumbing system will last longer if you keep up with the maintenance on them. Despite the fact that your tankless water heater is a smaller system than a traditional tank, it still includes parts that might fail or become damaged as a result of scale building. On-demand water heaters are fantastic for providing rapid hot water when you need it. The fact that they do not require you to continually heat the water to high degrees helps you save money on electricity.
If properly maintained, the majority of these units will live for well over 20 years.
Over the years, we’ve worked with a wide variety of water heater systems of various shapes and sizes.
- Tankless water heaters for residential and commercial use
- Gas and electric tankless water heater maintenance
- Water heater flush outs
- Water heater tune-ups
- Gas leak testing
Tankless Water Heater Maintenance
Your tankless water heater will need to be inspected by a certified New Jersey plumber to ensure that there are no leaks and that the equipment is in perfect operating condition. Tankless water heaters that run on natural gas must also be checked for gas leaks and venting issues before use. Tankless water heaters that are powered by electricity require regular electrical inspection and testing. It is also necessary to examine and test the control panel and the thermostat on the premises. Other components and functions, such as the heating elements, should be checked by your plumber as well.
Because we are water heater professionals, you can rest assured that we will do the job thoroughly and efficiently.
Yearly Tankless Water Heater Flushing
Hard water creates scale accumulation in the plumbing system as well as in the tankless water heater, among other things. A yearly cleansing is required to guarantee that hard water deposits do not damage your water supply and that the water heater lasts as long as it possibly can. The de-scaling flush will be performed by our certified plumbers at Water Heaters NJ as part of an annual checkup. It is a crucial service that helps to keep your water heater operating for a longer period of time and with fewer difficulties.
The hardness of your water determines whether or not you need to clean your tank on a yearly basis.
Every six months, some water needs to be flushed because it contains too much calcium and magnesium to function properly. Because the water in New Jersey may be somewhat hard, it is recommended that you get your water heater flushed at least once a year to avoid the need for costly repairs later on.