How To Restart Pilot Light On Water Heater - ERNIEGRAVES

How To Relight the Pilot Light in Your Gas Hot Water Heater

When the hotwater heater in your home fails, duties such as showering, doing laundry, cleaning dishes, and other household chores come to a grinding halt. If you have a gas-powered hot water heater, it is possible that the pilot light has gone out, which is the root cause of the problem. In most circumstances, if you relight the pilot, you should be able to go back into the air again. In this post, we’ll demonstrate how simple it is to complete the task yourself.

What does the pilot light do?

The pilot light of your gas hot water heater is a tiny, continuously burning flame that serves to start the burner of the appliance. To put it another way, if the pilot light goes out, the unit will be unable to heat water. It is possible for a pilot light to be extinguished for a variety of causes, including something as simple as a short stoppage in the gas line or an air bubble in the gas line. Warning: If you smell gas at any stage throughout the process, leave the area immediately and contact your energy supplier as soon as possible.

Steps to relight the pilot light.

Remove your foot from the gas pedal. Find the gas shut-off valve on your hot water heater and turn it off. The knob should be labeled in a clear and understandable manner. Turn the switch to the “Off” position and wait 5-10 minutes to ensure that all of the gas has been expelled. Locate the pilot light access point. Most of the time, this will be under the gas valve. To locate the burner and two gas tubes, open the pilot cover (if one is present) and use a flashlight to peer inside the hole to locate the burner and two gas tubes
Return to the gas valve and turn the knob to the “Pilot” position. By depressing the knob all the way down, you will begin to feed gas to the pilot. There are certain hot water heaters that include a separate pilot button
If this is the case, press that instead. While maintaining control of the knob or button, reach into the access and ignite the pilot with an extended lighter while still keeping it down. Once the pilot light comes on, keep the knob/button down for about one minute. Release the knob/button carefully after that period of time, and make sure that there is still a flame emanating from the pilot. Return to the gas valve and turn the knob to the “On” position. Typically, a noise will be heard to indicate that the primary burner is lighting
After giving the heater enough time to restart, replace the access cover and inspect the hot water supply.

What happens if the pilot light goes out again?

The gas pedal should be depressed. On your hot water heater, locate the gas shut-off valve by turning the knob clockwise. Clearly labeled knobs are recommended. To turn it off, press the “Off” button and wait 5-10 minutes to ensure that all of the gas has been expelled. Identify where you can get to the pilot light. Most of the time, this will be located beneath the gas valve. To locate the burner and two gas tubes, open the pilot cover (if one is present) and use a flashlight to peer inside the hole to locate the pilot and two gas tubes; Turn the knob on the gas valve to the “Pilot” position.

A separate pilot button may be present on some hot water heaters, in which case it should be depressed.

Holding the knob/button down for about one minute after the pilot lights will ensure that the pilot stays lit.

Most of the time, you’ll hear a popping sound as the primary burner ignites.

Toss the gas pedal to the floor. Locate the gas shut-off valve on your hot water heater and cut it off completely. The knob should have a clear label on it. Turn it to the “Off” position and wait 5-10 minutes to ensure that all of the gas has been expelled. Locate the access point for the pilot light. Most of the time, this will be located under the gas valve. Open the lid to the pilot (if one is there) and use a flashlight to check inside the hole to locate the burner, as well as two gas tubes
Return to the gas valve and choose “Pilot” from the drop-down menu. By depressing the knob all the way down, you will begin to pour gas into the pilot. A separate pilot button may be present on some hot water heaters, in which case it should be used instead. While still holding down the knob or button, reach into the access and ignite the pilot with an extended lighter
Once the pilot light comes on, continue to hold the knob/button down for about one minute. If there is still a flame coming from the pilot after this period, cautiously release the knob/button. Return to the gas valve and turn the knob to the “on” position. Typically, a noise will be heard to indicate that the primary burner is lighting. After giving the heater time to restart, replace the access cover and recheck the hot water.

How to Relight Your Water Heater Pilot Light (For Every Major Brand!)

The pilot light on your hot water heater has great influence on your life. Anyone who has walked into their shower on a frigid winter morning, with their body freezing and their teeth chattering as they wait for hot water that never arrives, knows what I’m talking about. In the case of a natural gas water heater, this might indicate one of two problems. There are two possibilities: either (1) the gas supply has been switched off or (2) your pilot light has gone out. We should first address the likelihood that your gas supply has been interrupted (and as fast as possible).

1. How to Make Sure Your Gas Supply is On

The pilot light on your hot water heater has great influence over your daily life and activities. Anyone who has walked into their shower on a frigid winter morning, with their bodies freezing and their teeth chattering as they wait for hot water that never arrives, knows what I’m talking about. There are two possibilities when it comes to your gas water heater. There are two possibilities: either (1) the gas supply has been turned off, or (2) your pilot light has gone out. Consider the likelihood that your gas supply has been turned off initially (and as fast as possible).

Examining your gas line is the first step in determining whether or not you have a lack of hot water.

Double-check to see that the gas shut-off valve is in the “ON” position. If everything is in working order with your gas supply, it’s time to check the pilot light on your water heater.

2. How to Light Your Pilot Light Water Heater

Depending on the manufacturer, re-igniting a pilot light may need a different procedure. Fortunately, there are just a few number of producers. The first step should be to check for the installation instructions, which are normally fastened to the water heater. Don’t be concerned if you can’t locate them. Specific brand-by-brand instructions are provided in the section below. Instructions in this video are “generalized,” as the title indicates. Scroll down to the bottom of this page for instructions unique to your brand of water heater.

How to Light a Rheem Hot Water Heater Pilot Light

The pilot light on an ARheem water heater must be manually activated by striking thepiezo ignitor striker that is incorporated within the water heater.

Using a clockwise motion, turn the gas knob on your Rheem water heater until it is at the desired position
Counter-clockwise turn the temperature dial on the water heater until it is set to the lowest temperature setting. Wait five minutes to let any gas in the water to pass through
Remove the outer door of your Rheem water heater from its mounting bracket. Counter-clockwise turn the gas knob to the “Pilot Light” setting until it is in this position. Press the red button to the left of the gas knob until it becomes depressed. The piezo ignitor striker is located on the left side of the gas knob. While maintaining pressure on the red button, continually push the piezo ignitor striker until the pilot light is re-lit until the problem is resolved. Through the viewing glass on the inside of the Rheem water heater’s inner door, you can see the pilot light. After the pilot light has been turned on, continue to hold down the red button for one minute before releasing it completely. The pilot light will remain on during the process. Remove and reattach the outer door of your water heater
To turn on the gas, turn the knob to the “ON” position. Set the hot water temperature slider to the temperature that you desire for your water

How to Light an A.O. Smith or State Water Heater Pilot Light

AO Smith water heaters andState water heaters, including the Conservationist model, are equipped with a piezoelectric igniter mechanism that lets you to light the pilot by pressing the ignition button on the water heater.

Disconnect the access panel from the side of the A.O. Smith or State water heater and place it somewhere out of the way
To turn off the gas supply, turn the control knob on the water heater’s side to the “OFF” position and let the room air out for roughly 10 minutes. The “Pilot Light” setting on the gas control knob should be selected. The red button should be pressed down (this will allow the gas to flow to the burner assembly)
And While maintaining pressure on the red button, press down on the ignitor button until the pilot light illuminates. It is possible that you may have to press down on the ignitor button two or three times before the hot water heater pilot light turns back on. Continue to hold down the red button for approximately 60 seconds after the pilot is lighted, then gently release the button. Make sure the gas is turned on by turning the control knob to “ON.” Replacing the access panel on the side of the water heater is necessary.

How to Light a Bradford White Water Heater Pilot Light

Control panel for the Bradford White water heater should be turned off
Allow the water heater to stand for 5 minutes to allow gas to escape from the system. Change the mode of the control switch to pilot light mode. Press the red control button in for a few seconds, then press the button every few seconds while continuing to press in
Listen for a click, and the water heater status light should begin flashing to indicate that the water heater is operational. Allowing the red control button to be released
Make sure that the red control button is in the “hot” position. If the pilot light does not stay lighted or does not relight after being extinguished, it is possible that a more serious problem is causing your lack of hot water. For emergency assistance, contact your plumber.

Resources

Precautions to take when using a water heater
How to get hot water back from your water heater
The components of a water heater
Water heater maintenance and repairs
What is the average lifespan of a water heater?

Call 1-Tom-Plumber

It might be rather frightening to experiment with the gas in your house. Don’t be concerned, we’ll have you back in a warm shower in no time! Please do not hesitate to contact us or call 1-Tom-Plumber (1-866-758-6237). Regardless of the nature of the emergency plumbing, drainage cleaning and drain clearing, or water damage situation, we will respond quickly. This includes excavation of subterranean water pipes and sewage main lines.

How to Light a Water Heater Pilot Light

Prev PostNext PostWhen the pilot light on a water heater goes out, it is typically because of a natural fluctuation in gas pressure, which extinguished the flame. The most obvious indicator that a pilot light has gone out is the one that everyone dreads: the water will not heat up properly. In the event of a damaged flame sensor, it’s critical to know how to relight the pilot light on your water heater so you can get the flame going as quickly as possible. This will not only allow you to get your hot showers back, but it will also ensure that no gas is unintentionally discharged into the home.

However, for the vast majority of gas-powered water heaters, you should begin by locating the gas shut-off valve on the water heater, which is generally plainly labeled on the front lower section of the water heater, before proceeding.

Open the door or cover that provides access to the pilot light. In most cases, this will be positioned under the gas valve
However, some water heaters will just have an open gap where you can see the pilot light burner instead. Locate the burner within the container using a flashlight or a headlamp. It will be reached by two little gas tubes. You’ll want to keep an eye on it while you’re at work. Turn the gas knob to the “Pilot” position and push and hold the button. This will initiate the flow of gas, allowing you to ignite the flame. Some water heaters feature a separate pilot mode button, which is commonly a red button, which you must push and hold in order to activate it. While keeping the gas pedal depressed, ignite the pilot light. Certain water heaters feature an igniting button that is red or black, while others must be lighted manually with a long lighter
Some models include a red or black igniting button. Maintaining pressure on the gas knob or button for a full minute after the flame is ignited is critical. Then slowly release it while checking to see if the light is still on. Turn the gas knob to the “On” position and listen for the unmistakable “whump” or whooshing sounds that indicates the main burner has ignited. Enjoy your hot shower when you’ve replaced the lid.

Access to the pilot light should be gained by opening the door or covering it. In most water heaters, this will be found under the gas valve; however, some water heaters just have an open gap where you can see the pilot light burner instead. Locate the burner within the container using a flashlight or a headlamp. Into it will be accessed by two little gas tubes Watching it while you’re at work will be beneficial. Then, while holding down the gas pedal, turn the knob to “Pilot.” Starting the flow of gas will allow you to ignite the flame more quickly.

Others must be manually ignited by holding a long lighter over the igniting button on certain water heaters, while others have a red or black igniting button on their side.

then slowly release it while checking to see if the light is still illuminated: Make a noticeable “whump” or whooshing noise as the main burner ignites after turning the gas knob to the “On” position.

What is a Thermocouple?

A thermocouple is sometimes referred to as a flame sensor in contemporary water heaters because of the way it detects flames. Your thermocouple is most likely twisted, filthy, or damaged if the pilot light continues to go out after you have completed the above-mentioned lighting procedures. For those who find that their pilot light is twisted and not near the burner, they may simply turn off the gas, shift it over, and attempt lighting the pilot again. It may be necessary to clean the water heater gas valve and the main gas line near the heater if this does not solve the problem.

The burner is typically simple to remove by simply sliding it out.
If this doesn’t solve the problem, you may get a new thermocouple for less than $15 at any hardware store or home improvement center.
Rooter Plumbing to help you get hot water back into your home again.
The use of hot water is simply one component of a great showering experience.
Previous PostNext Post Previous Post

Why Your Water Heater’s Pilot Light Keeps Going Out & How to Fix It

The date is May 13, 2021. When the pilot light flame on your gas water heater goes out, it is an annoying and frustrating situation to have to deal with. When your water heater’s pilot light fails to stay lit, you’re left without hot water, which makes even the most basic of tasks such as taking a shower a chore. Naturally, you question, “How did this happen? What happened?” Is there anything you can recommend to help you get things going again? What should I do to have it repaired? “May you tell me about the costs I can expect?” Fortunately, if your water heater pilot light goes out, you should be aware that this is a frequent problem that many homeowners have and that the time and effort required to repair it is low.

Why does the pilot light on my water heater keep going out?

05.13.2021, Friday, May 13 Being faced with the uncomfortable and annoying situation of having your gas water heater’s pilot light flame go out is a difficult situation. The lack of hot water may make even the simplest task like taking a shower a chore when your water heater’s pilot light fails to stay lit. Of course, you’re thinking, “How did this happen? Any hints or suggestions for re-igniting the fire would be appreciated. When will it be repaired and how do I go about doing so? “Can you tell me about the costs?” In the event that your water heater pilot light fails, you should be aware that this is a typical problem that many homeowners have, and that the time and effort required to replace it are modest.

Please allow us to guide you through some of the most frequent reasons why your water heater isn’t heating and how to resolve this issue if your pilot light won’t stay lit and you are unfamiliar with water heaters.

Thermocouple Issues

When your pilot light is on, your thermocouple detects the presence of the flame. The thermocouple’s tip is positioned above the pilot flame, providing a voltage that maintains the gas valve open in the process. A thermocouple will shut down the gas supply to your water heater if it detects that the pilot light on your water heater is not lighting up properly. When thermocouples are exposed to moisture or dust for an extended period of time, they might malfunction, gather dust, or get bent away from the pilot light’s flame.

Lack of Combustible Air

Another reason why your gas water heaterpilot light won’t remain lighted might be that there isn’t enough combustible air in the room where it is located. To keep the pilot light on in your water heater, you’ll need to blow air into it. Otherwise, the flame will be extinguished. Take precautionary measures to ensure that the water heater is not surrounded by material, such as litter or lint, which might increase the quantity of combustible air present. Maintain as much cleanliness as possible in the surrounding region.

What do I do if my water heater pilot light keeps going out?

Try to rekindle the spark on your own first, if at all possible. Take the following general steps:

Locate the gas shut-off knob and turn it all the way to the “Off” position. The gas flow is halted as a result of this. Allow for a few minutes for the gas to dissipate before continuing. To get access to the burner, remove the access panel. To begin the flow of gas, turn the knob to the “Pilot” position. You’ll want to press and hold the knob down for a few seconds. While still holding the gas knob, ignite the pilot with a long lighter while still holding the gas knob. To ignite your gas water heater, use the button on the side of the tank that says “ignite.” As soon as the flames have been extinguished, turn the gas knob to the “On” position and wait for the main burner to come on.

If you are unable to relight the pilot or if your pilot light keeps going out, it is possible that you have another problem, such as a faulty thermocouple, to consider. Please refer to the owner’s handbook for your water heater equipment for further information.

Can I replace a thermocouple myself?

Yes. In the event that you are handy with tools, you may be able to change the thermocouple yourself. It is easier to accomplish this by turning off the gas valve and removing the entire burner and thermocouple assembly. In the case of minor repairs, it is preferable and safer to hire someone who is knowledgeable in the field of repair. A specialist may also evaluate your water heater for other faults and provide advise or ideas on how to deal with any existing or future difficulties that may arise.

Call BGE HOME

Please contact BGE HOME at (410) 918-5600 if your water heater pilot light will not light or continues going out. You may also contact us online. Our licensed specialists are available 24 hours a day, seven days a week to come out and inspect your water heater and make recommendations on how to get it running safely and effectively again. This item was posted on Thursday, May 13th, 2021 at 4:09 pm and is filed under Uncategorized. Commenting and pinging are temporarily closed for this post.

How to Reset a Gas Water Heater Pilot Light

Home-Diy You might be interested in learning how to reset the pilot light on your water heater. if (sources.length) then this.parentNode.removeChild(sources); if (sources.length) then alternatively, if this.onerror = null, this.src = fallback; )(, arguments.target.currentSrc.replace(), ‘/public/images/logo-fallback.png’), ‘/public/images/logo-fallback.png’) otherwise ” loading=”lazy”> ” loading=”lazy”> Is there no hot water?

Are you interested in discovering the safest method of re-establishing hot water flow? Are you looking for a technique to turn on the pilot light without calling a professional to help you? This eHow article will show you how to ignite the pilot light on your water heater in step-by-step directions.

Check the temperature of the water by turning on the hot water in the shower or sink and dipping your hand into the stream of water. Is the water really chilly? Turn on the water for approximately 60 seconds. If the water is still ice cold, it’s possible that your pilot light has gone out. If your home is more than ten years old, you should let the water run a bit longer. Read the owner’s handbook for your water heater. Look through your water heater’s documentation for the owner’s manual. For more information on where the pilot light is placed, consult the owner’s handbook. If you are unable to locate the handbook, look for a telephone number on the water heater itself. Make a note of the model and serial number, and see if you can locate the company’s website by searching for it. Check to see whether your gas water heater is still covered by the manufacturer’s guarantee. Locate the water heater in your residence
To find your water heater, you’ll need to climb into the attic or walk into the garage. Before you do anything, make sure you read the directions on the water heater. Check the area around the gas water heater for the smell of gas. Make it known to everyone in the home that you are working on the gas water heater. Locate the temperature control dial and lower the water’s temperature to the hottest setting available. To turn off the pilot light, turn the dial on the pilot light to the off position. Hold your breath for 10 minutes and then check for gas again. If you smell gas, do not attempt to fire the pilot light until the smell has been extinguished. In order to obtain service, contact your local gas company. If you do not detect any gas, move on to the following step
Otherwise, stop. The pilot light should be reset by turning the dial to the pilot position. There should be a button that allows you to turn off the gas. Most of the time, this will be a red button or a button with a fire logo or image on it. Continue to press the button until it clicks. Now, while still holding down the button, press the igniter switch. It’s likely that you’ll hear another clicking sound. Repeat this procedure many times, and the pilot should relight on its own. If you wait for one minute while holding the red button, the light will remain on. If you release the button, the light will turn off. If the light goes out while you’re doing it, try it again. It is possible that your gas water heater may require expert servicing if the light continues to blink after three attempts. Check the temperature of the water
Turn the dial to the ON position and adjust the temperature to the WARM setting to complete the process. After one hour, check the water in the shower to make sure it is still running. The water should be warm, but not too hot, to avoid burning your skin. Set the temperature slider to the desired level of warm or hot water for your requirements. Check the pilot light on a regular basis to make sure it is still lighted

The Drip Cap

You might be interested in learning how to reset the pilot light on your water heater. Find out where the pilot light is placed by consulting the owner’s handbook. If you smell gas, do not try to fire the pilot light
Instead, call 911. Once again, you should hear a clicking sound
If the light fails to come on, try it again. It is possible that your gas water heater may require expert servicing if the light continues to blink after three attempts. Make sure the water is at the proper temperature. To turn on the heater, turn the dial to the ON position and select the WARM setting

How to Light the Pilot for a Gas Hot Water Heater

Learn how to reset the pilot light on your water heater by reading this article. Find out where the pilot light is by consulting the owner’s handbook. Attempting to fire the pilot light if you smell gas is not recommended. Once again, you should hear a click sound; It is recommended that you try again if the light goes out. It is possible that your gas water heater may require expert servicing after three attempts if the light continues to blink. Water temperature should be checked. To turn on the heat, turn the dial to the ON position and select the WARM setting;

1.

Find the gas regulator valve on the water heater and turn it on. It is positioned on the exterior of the water heater, near where the gas line enters the device, and it is controlled by a knob on the outside. The gas supply to the pilot burner beneath the hot water tank is controlled by this valve. To turn the valve off, turn the knob all the way to the left. Wait five minutes before continuing. Locate the pilot burner, which is located beneath the natural gas water heater. Remove or unsnap any access cover that is preventing you from getting to the burner. Make use of the flashlight to illuminate the pilot burner

2.

Turn the knob on the gas regulator valve to “Pilot,” press down on it, and keep it pressed down. The flow of gas to the pilot burner is initiated by pressing this button. To start the pilot burner gas flow on some water heater types, you must push and hold down a separate red button for a period of time. Find a red or black button labeled “Ignition” on the top or side of the gas valve if your heater has a piezoelectric spark pilot igniter built in. To start the pilot, press the button on the control panel. As the igniter ignites, you will hear a click sound. If you must manually ignite your heater, a long-necked barbeque lighter is the most secure type of lighter to use. Light the pilot burner with a lighter flame and turn it on.

3.

After the pilot has been ignited, keep the regulator valve knob firmly depressed for at least one minute. This permits the pilot flame to heat the thermocouple safety sensor, which detects the presence of a live pilot flame, allowing the pilot flame to heat the sensor. Reduce the pressure on the regulator valve knob gradually. When the pilot light continues to glow after you have released the knob, turn the knob to the “On” position. During the ignition of the primary burner, you should hear a muffled “whoomp” sound.

Things You Will Need

Look for a label on your gas water heater that provides particular pilot lighting instructions for the model of water heater you have installed.

Warning

If you smell gas in the vicinity, it is not a good idea to attempt to relight a water heater pilot light (or to do any other maintenance on the device). When you are outside the home, dial 9-1-1.

Solved! What to Do When Your Pilot Light Goes Out

Image courtesy of fotosearch.com The temperature in my shower this morning was absolutely freezing, and I mean that in the best way possible. After a brief investigation, I noticed that the pilot light on my water heater had gone out. Is it worth it to try to relight it? A: It all depends on what caused the light to go out. It’s possible that the problem was anything as simple as a draft, a filthy pilot orifice, or a worn-out part—or that the extinguished pilot light was a symptom of something more serious requiring attention.

If you find yourself in this situation, leave your home and call the gas company!

(Please keep in mind that if your water heater has an enclosed burner chamber, you’re most likely out of luck as far as a DIY remedy is concerned; only a professional plumber should be able to reach an enclosed burner chamber.) Make an appointment with a proGet free, no-obligation repair quotes from qualified appliance experts in your area.

When you see your pilot light out, you can usually relight it.

Featured image via fotosearch.com QUESTION: I hopped into my shower this morning and holy cow, was it freezing! The pilot light on my water heater had gone out, as I noticed after a short check of the appliance. Trying to relight the cigarette seems like a bad idea. A: How long does it take to replace a light bulb? Perhaps there was a minor issue, such as a draft, a filthy pilot orifice, or a worn-out item, or perhaps the extinguished pilot light was an indication of something more serious. To begin, identify the likely source of a broader problem by observing: Is there a gas smell?

If this is the case, continue reading to see how you may resolve the issue on your own time.

Ask the expertsObtain no-obligation repair quotes from qualified appliance professionals in your area.+

If the flame continues to burn, you’re good to go!. Simply replace the cover plate, turn the control knob to the “On” position, and set the desired temperature on the water temperature knob to return to the refreshinghotshower experience. Ensure that the pilot light does not flicker and goes out immediately after relighting by cleaning the pilot orifice. Gas flow is impeded by a clogged pilot light aperture, but the solution is straightforward. Shut off the gas to your water heater first, of course (look for a valve on the gas line that supplies the unit). Twist the pilot orifice fitting to the left, which is positioned behind the access cover, to release it from its mounting. After that, remove the orifice itself from the fitting by unscrewing it. Using a cotton swab moistened with rubbing alcohol, thoroughly wipe all surfaces of the fitting once it has been dismantled. As soon as you have completed the reassembling and reattaching of the fitting, relight the pilot light as previously specified. You should replace the thermocouple if you are able to ignite the pilot light but it goes out as soon as you remove the control knob from the pilot light control box. It is a safety device that shuts off gas flow if it detects that the pilot light is out
However, if it becomes broken, it loses its capacity to regulate the flow of gas. This repair is a little more involved than the previous two, but a replacement is rather inexpensive—often costing less than twenty dollars

Step by Step Guide: How to Light a Water Heater

Get your hot water heater up and operating in a safe and efficient manner. Get quotations from as many as three professionals! Enter your zip code below to get matched with top-rated professionals in your area. You should examine your hot water heater first if your hot shower has turned into freezing rain after you have turned on the hot water. Homes using gas water heaters should check their pilot lights to be sure they haven’t been turned off accidentally. The age of your heater may determine whether or not you may use an ignition button or a lighter to relight the pilot light on it.

The following tools and materials will be required:

How to Relight a Gas Water Heater’s Pilot Light

To relight a hot water heater, just follow the instructions outlined in the following section.

1. Safety First

Even though the vast majority of homeowners are capable of relighting a pilot light on their own, it’s crucial to use caution when working with a gas-powered hot water heater. When relighting a pilot light, you should always proceed with caution since the gas used to power your hot water heater is volatile and possibly deadly. If you smell gas at any time, you should turn off the gas valve immediately and open the windows to let the gas escape. Do not switch on any lights. Leave your home and call the gas company or the fire department for assistance.

2. Turn Off the Gas

First and foremost, you must switch off the gas supply before re-igniting the pilot light. Locate the gas valve on your hot water heater and turn it to the “off” position to turn the water off. Hold off for around 10 minutes; this will give any gas in the region time to clear, which is vital because the gas is very combustible, so patience is required.

3. Access the Pilot Light

It is customary for the pilot light to be situated directly beneath the gas valve. In certain circumstances, a door or cover may be placed over the light to prevent it from being seen. While you are doing this procedure, use a flashlight to ensure that you can see everything clearly and accurately.

4. Turn the Gas Valve to ‘Pilot’

Turn the gas valve to the “pilot” position and push the button.

As a result, the gas valve provides enough gas to ignite the pilot light, which is what you want. If your hot water heater is equipped with a separate pilot button, this is something to look for.

5. Light the Pilot

The method you use to relight the pilot on your gas water heater is determined on the age of the appliance. Gas water heaters manufactured during the last eight years are not required to include manual illumination. Instead, these water heaters are equipped with an electric spark generator, similar to that found in a gas grill. To ignite the pilot light on a water heater that has a pilot light ignition button, you should press the button until the pilot light illuminates. If your water heater does not have such a button, you’ll have to manually ignite it with a long lighter if it does not have one.

6. Turn On the Gas

Once the pilot light has been lighted, re-ignite the gas supply.

7. Don’t Be Afraid to Ask a Professional

Turn the gas back on when the pilot light has been lit.

FAQs About Hot Water Heaters

Photograph by Hmzalldesign/iStock / Getty Images Plus courtesy of Getty Images If your water is barely lukewarm, it is possible that your hot water heater is malfunctioning. It might be a sign that your water heater is going to malfunction, that sediment has accumulated, or that the temperature has been adjusted improperly. In order to establish the specific nature of the problem, you need consult with a water heater repair professional.

How much does it cost to repair a hot water heater?

The cost of repairing a hot water heater can range from$225 to $960 depending on the model. The cost of repairing a water heater varies based on where you reside and what is wrong with it. In certain circumstances, it may be more cost effective to replace your hot water heater rather than repair it.

How do I maintain my water heater?

Some things you can do to keep your hot water heater in good working order include examining it on a regular basis and flushing it out of the tank.

How to Fix a Water Heater Pilot Light

Time Approximately one hour or less Complexity Cost for a beginner is less than $20.

Introduction

If your hot water heater suddenly stops operating, it’s likely that a faulty thermocouple has caused the gas to the pilot light to be turned off. Replacement is a simple do-it-yourself project.

Tools Required

Is there no hot water? If you have a natural gas or propane water heater, there is a good probability that the pilot light has gone out. It is this little flame that starts the gas burner on your water heater that is referred to as the pilot light. When the pilot light on your water heater goes out, the first thing you should do is try to relight it by following the instructions on the water heater label. The thermocouple is by far the most prevalent cause of pilot failure, whether it occurs immediately after lighting or on a regular basis after the pilot has been extinguished.

If you do not wait for a professional to arrive, you will be able to get your hot water running without incurring the expense of a service visit.

What is a Thermocouple?

In order for gas to flow to the burner, a thermocouple must be used to detect the heat of the pilot. A faulty thermocouple will prevent gas from reaching both the pilot and the burner, resulting in the pilot light failing to stay lit.

Project step-by-step (6)

Shut off the gas line by closing the cutoff valve. As seen in this photo, turn the valve a quarter turn so that the handle is at a right angle to the pipe.

Unscrew the Nuts

Turn off the control valve if it is on. Remove the burner access covers and loosen the bolts on the gas, pilot, and thermocouple lines to free up the burner.

Sign Up For Our Newsletter

Complete your do-it-yourself tasks like an expert! Become a subscriber to our newsletter! Do It Right the First Time, and Do It Yourself! Step number three.

Remove the Assembly

Professionally complete your home improvement projects! Become a subscriber to our mailing list! It’s important to do things right the first time. Three-pointed strategy

Install the New Thermocouple

Install the new thermocouple in the same manner as the previous one
Replace the burner assembly by sliding it back in. Reattach the three wires to the control valve where they were disconnected.

Reattach the Lines to the Gas Valve

Installation of the new thermocouple is identical to the installation of the previous one. re-insert the burner assembly into the burner assembly The three wires to the control valve should be reconnected.

Pro tip: Because the metals are delicate, avoid overtightening them.

Test for Gas Leaks

Don’t overtighten the metals because they are soft.

Replenish the water supply by opening the shutdown valve and lighting the pilot light. Turn the control valve to the “on” position. Use a 50/50 mixture of dish soap and water to check the screw joints for air bubbles, which indicate a leak, while the gas burner is turned on.

Replenish the water supply by opening the shutdown valve and lighting the pilot light
The control valve should be turned on. Testing for leaks in screw joints should be done when the gas burner is turned on with a 50/50 mixture of dish soap and water.

CAUTION!

During this procedure, you should not be able to detect the scent of gas (except for a slight whiff when you remove the gas lines).

If you find yourself in this situation, exit the house immediately and contact your gas provider.

WhenNotto Replace the Thermocouple

Some gas water heaters have a burner chamber that is “closed,” making it impossible to reach the burner. It is recommended that you contact a professional to repair this sort of heater. In addition, some gas water heaters are not equipped with pilot lights. Allow the professionals to take care of this as well.

Why Your Pilot Light Keeps Going Out & How To Fix [With Pictures]

That darn pilot light just won’t stay turned on! Moreover, it is causing all of your plans for today to be derailed. Nothing compares to the sensation of taking a hot water shower. However, there are times when this does not occur. After all, there are worse things than having a very cold bath, should we say? The one thing that everyone despises is a lack of running water. This may be incredibly inconvenient – not only for showering, but also for all of the other duties that require hot water to be completed successfully.

You don’t have to put your day on wait because your pilot light isn’t working properly.

However, if you discover that your water heater is leaking water and that this is the root of your water problem, read our guide on what to do when your water heater is leaking water!

What’s A Pilot Light?

An electronic device that maintains a continually burning flame is known as a pilot light. Basically, the goal of this section is to light the burner. How? When you switch on your appliance, gas is released from the main burner, and the pilot light flame ignites the gas, so supplying heat to the room. With each degree of heat generated by the main burner, the air or water contained within your appliance is heated and then disseminated as needed around your residence or place of business

Appliances With Pilot Lights

Water heaters, older furnaces, and boilers are more likely to have a pilot light than other types of appliances. You may also discover that your gas fireplace has a pilot light, which is a good thing. Learn how to switch on the pilot light on your gas fireplace by visiting this page. Pilot lights have been gradually being phased out in favor of hot surface igniters or spark igniters in more recent years. pilot light for a water heater The pilotflame ignites the gas, which generates heat for your house or place of work.

Also, if you are experiencing no heat, check to see whether the pilot light on your furnace or boiler has gone out.

Water Heater Pilot Light: Where Is It And What Does It Do?

A little access panel, located just underneath the thermostat, may be found at the very bottom of your gas water heater. The pilot light for the gas water heater is located within the access panel. There will be a gas panel where you may check to see if the pilot flame has been ignited. The pilot light on your water heater is a little flame that is used to ignite the gas burner in the water heater. This is required for the purpose of heating the water that will be dispersed around your home. If you are experiencing no hot water and have attempted to relight your pilot light without success, you will require water heater repair.

The pilot light on the water heater keeps going out. Warning! Remove the burner and pilot from the interior of your water heater at your own risk. This photograph was shot by a water heater professional for the purpose of giving a demonstration on the use of pilot lights.

What Makes Your Water Heater Pilot LightGo Out

Thermocouple on the water heater is faulty. The thermocouple is responsible for detecting whether your pilot light is on. This copper rod serves as a safety precaution, preventing the heater’s gas supply from being turned off if the pilot light on the water heater goes out. The natural wear and tear of a thermocouple can cause it to get twisted out of place, to malfunction, to become broken, to become covered in dirt, or to accumulate carbon deposits. When one or more of these conditions occurs, the thermocouple will be unable to reliably detect the pilot light and will subsequently shut down the heating system.

Strong Breeze Can Blow Out Pilot Light

In some cases, such as when there is heavy wind or a nearby draft, your pilot light may be extinguished. Unless your pilot light has simply been out, you should have little trouble re-igniting it and keeping the flame burning.

Kink in the Flex Tube

The fuel is delivered to the gas controller by flexible tubes. Gas will not flow through the tube if there is a kink or twist, which can also lead to pilot light difficulties.

Filthy Pilot Light OpeningCan MakePilot Light Keeps Going Out

If the pilot’s mouth is clogged with muck and debris, it will be virtually hard for it to maintain a flame. It will only keep a modest flame that will be readily extinguished if it does catch fire. Your pilot light will not stay lit if your pilot orifice is clogged with debris.

How Do I Re-Light My Gas Water Heater Pilot Light?

A clogged pilot’s mouth makes it practically hard for it to maintain a flame when it’s loaded with crud and dirt. It will only keep a feeble flame that will be readily extinguished if it does manage to ignite. It is impossible for your pilot light to remain lit if the pilot orifice is clogged.

Step 1: Thoroughly Read Gas Water Heater Manual

To have a better knowledge of where each component of your water heater is situated, consult your water heater’s instruction manual.

Step 2: Turn Down Thermostat

To have a better knowledge of where each component of your water heater is situated, consult your water heater handbook.

Step 3: Turn OFF Gas

Locate your water heater’s owner’s handbook to have a better grasp of the components of your water heater.

Step 4: After 5 Minutes, Turn The Gas Control Valve Setting On Water Heater To “Pilot”

Turn the gas control valve, which is situated on the water heater, to the “Pilot” position. The word “Pilot” should be in the center of the image.

Step 5: HoldDownthe Reset Button

Keep the water heater reset button depressed. After that, press and hold the reset button. This is a button that is often red in color and is situated to the left of the gas control valve. Keep your finger on this button. To be on the safe side, use the instructions to identify each component.

Step 6: While Holding Down The Reset Button, Press TheIgniter

Keep the water heater’s igniter down. The igniter is located to the right of the gas control valve. While continuing to keep the reset button down, press the igniter button on your keyboard. Click on the water heater’s gas window until you see a blue flame appear in the glass.

Step 7: Continue To Hold Down The Reset Button For 20-30 Seconds.

Following the sighting of a flame and the removal of your finger from the igniter, you must continue to press the reset button. Continue to hold the button down for another 20-30 seconds.

Step 8: Turn The Gas Control Valve To The “On” Setting

It is necessary to maintain pressure on the reset button after you have seen a flame and removed your finger from the igniter.

For a further 20-30 seconds, push and hold the button down.

Step 9: Turn The Thermostat Up

Increase the temperature of the water heater. Now is the time to dial up the heat in order to get that hot water flowing again!

Step 10: Enjoy Your Warm Water, Or Ask For Help!

If you try to relight the pilot light and it does not stay lit, you may want the services of a professional to assist you with your water heater repair.

But What If You Don’t Have A Manual Igniter?

After that, remove the access panel that is located beneath the water heater thermostat and discard it. You can use a wrench to help you.

After 5 minutes, Turn Gas Control Valve To “Pilot”

Now, set the gas shutoff valve to the “Pilot” position.

Next, Hold Gas Control Valve Down And Ignite Pilot With A Lighter

Keep the gas knob pressed down as you ignite the pilot using a long lighter, similar to a BBQ skewer. If your gas water heater, on the other hand, has an igniting button, use it instead.

Once TheFlame Is Lit,Turn Gas Control Valve to “On”

As soon as the pilot light is lighted, you may remove the reset button and turn the gas knob to the “On” position, which will take around 30 seconds. You should be able to hear the main burner turn on at this point. Your pilot light should now be able to maintain a flame, and hot water should be flowing again!

Furnace Pilot Light: Where It Is And What Does It Do?

Old furnaces rely heavily on the pilot light to generate heat, which is why it is so crucial to keep the pilot light on. When the gas valve is opened, the flame will continue to burn constantly, igniting the gas. The heat generated by this process then heats the air that is drawn into your furnace, which is then dispersed throughout your house. If your furnace’s pilot light is out, you may notice that it is spewing chilly air into the house. The failure of the pilot light is one of several probable causes of your furnace’s inability to switch on.

You may find the pilot light by following the gas line into your furnace and looking for it there.

From there, you should be able to see a short tube that runs from the gas valve to the burner itself.

Why Furnace Pilot Light keeps going out

There are a variety of reasons why the pilot flame on your furnace continues flickering out of control. Let’s get started!

Faulty Thermocouple Triggers Pilot Light to Go Out

It is meant to shut off the gas valve if the pilot light goes out, and it is used in conjunction with a thermocouple. Thermocouples can be damaged or worn out over time. If the thermocouple is incorrectly positioned or malfunctioning, the gas valve may be incorrectly shut off, as well as preventing the pilot light from keeping lit.

Dirty Thermocouple Makes Pilot Light Keeps Going Out

A filthy thermocouple may cause the safety mechanism to mistakenly trigger, causing the ignition to be turned off. The thermocouple has the potential to accidentally shut off the gas valve and extinguish the blazing flame.

Filthy Pilot Port/Orifice

Examine the flame. If the flame is becoming orange, contact an HVAC professional immediately. If you light your pilot and the flame is yellow, this indicates that your pilot opening is filthy and is preventing your pilot light from keeping lit for long periods of time. A buildup of dirt in the pilot light port might prevent the flame from fully enveloping the thermocouple, which can result in a faulty ignition.

As a result, the safety system is activated, which results in the gas being turned off. This is a fairly typical cause of why your pilot light keeps going out, and it is easy to diagnose.

Bad Gas Regulator

If you have gas appliances in your house, you will also have a gas regulator outside of your home to regulate the flow of gas into your home. Your furnace may not receive enough gas to keep its pilot light lit if your gas regulator isn’t functioning correctly. There is a good chance that you have a defective gas regulator if the pilot light is out in more than one home appliance, such as your water heater.

Bad Flue Venting Could Blow Out Pilot Light

Excess wind might enter via the openings in your flue pipe if it is loose, broken, or not correctly attached to the furnace. This would extinguish the pilot light flame.

A Strong Draft

There’s always the potential that a powerful draft knocked out your pilot light’s flame and caused it to go out.

How To Re-Light A Furnace Pilot Light?

The first and most crucial step is to locate the owner’s manual for your heater. The handbook will assist you in gaining a better grasp of the internal workings of your individual appliance.

Step 2: Identify Pilot Light

Firstly, it is critical to locate the instruction handbook for your furnace. A greater grasp of the inner workings of your particular furnace will be provided by the handbook.

Step 3: Turn OFF Gas

After that, locate the gas valve and shut it down completely. A tiny valve located towards the bottom of the furnace is standard on most models. In general, there are three settings for the gas valve: “ON,” “OFF,” and “PILOT.” Make sure the valve is in the “OFF” position by turning it clockwise. It is critical that you wait for at least 5 minutes after the previous step to ensure that all gas has been expelled from the pipes before proceeding. A disaster might occur if this is not done.

Step 4: WAIT 5 Minutes, then Turn Gas to “Pilot”

Immediately after waiting 5 minutes, switch the gas valve to the “PILOT” position. It is vital that all of the gas has dissipated before switching the gas position to the pilot position. A few of minutes might be the difference between a peaceful society and a disasterous one. Keep in mind that gas is quite explosive!

Step 5: Hold Reset Button

After that, hold down the reset button. However, if you are having difficulty locating the reset button, your furnace’s owner’s handbook should be able to point you in the appropriate place.

Step 6: Press Igniter While Holding Reset Button

Holding the reset button down for a second or two will allow you to activate the igniter and light the flame. Once the flame has been ignited, remove the igniter and continue to hold down the reset button until the flame has been extinguished. Keep the reset button pushed for 20-30 seconds to complete the process. To light the pilot when you do not have a manual igniter, you can use a BBQ lighter or a match. furnace with a pilot light

Step 7: Turn Gas to “ON” position

You should push the igniter to start a fire while you are holding the reset button pressed to keep it lit. Once the flame has been ignited, remove the igniter and continue to hold down the reset button until the flame is extinguished completely. Retain your finger on the reset button for 20-30 seconds. The pilot may be ignited using an ordinary BBQ lighter in the absence of an automatic igniter. the furnace’s pilot light

Step 8: If you Aren’t comfortable yet, call a pro!

If, despite doing the necessary measures, you are still unable to keep your pilot light lit, contact an HVAC professional for furnace repair.

Boiler Pilot Light: Where It Is And What Does It Do?

The pilot light in your boiler is vital for the boiler to function properly and generate heat. It is necessary for the pilot to burn constantly in order for it to ignite the gas when the gas valve is opened. When this occurs, your boiler starts heating the water, which is subsequently dispersed throughout your house to provide warmth. If your pilot light goes out, your boiler and central heating will not be able to operate properly. The pilot light is placed within your boiler, on the other side of the valve from the gas valve.

Why Boiler Pilot Light Goes Out

A malfunctioning, misaligned, filthy, or damaged thermocouple is frequently the source of your pilot light’s failure to illuminate properly. It is the thermocouple that keeps the gas valve from opening if the pilot light is not lit. Your pilot light may not function properly if there is an issue with your thermocouple, or if it is just coated with dirt and debris.

Dirty Pilot Opening

When you turn on your furnace pilot light and find a yellow flame, this indicates that your pilot light is unclean and is causing your furnace pilot light to constantly turning out. If dirt accumulates in the pilot light port, it may prevent the pilot light from completely enveloping the thermocouple with the flame it produces. This causes the thermocouple safety system to be incorrectly activated, resulting in the gas being turned off and the heat being turned off.

Weak Gas Regulator Can Make Pilot Light Keeps Going Out

If you have gas appliances in your home, you will have a gas regulator outside your home. The failure of your gas regulator may result in your furnace not receiving enough gas to keep its pilot light lit. In the event that you observe pilot light issues on more than one device, such as your water heater, it is possible that your gas regulator is broken or weak.

A Strong Draft

A strong airflow has the potential to completely extinguish your pilot light.

How To Re-Light Boiler Pilot Light

Make sure you are familiar with the components of your boiler by reading the instruction manual thoroughly. It is common for the owner’s handbook to contain instructions for re-igniting the pilot light.

Step 2: Shut OFF Boiler

Starting with shutting off the boiler is always a good idea.

Step 3. Shut OFF Gas

Locate the gas valve and turn it to the “OFF” position.

Step 4. Wait 10 Minutes

Continue to check the pipes for around 10 minutes to ensure there is no residual gas.

Step 5. Open Boiler and Locate Pilot Light

After a short period of time, you can turn on the boiler. To obtain access to the pilot light, remove the access panel from the wall. Typically, this panel is positioned next to the gas control knob box, which is where it gets its name. Sometimes you may simply lift the panel up, but other times it may be screwed to the wall or ceiling.

Step 6. Turn Gas to “Pilot”

Now, set the gas control valve to the “Pilot” position on the pilot valve.

Step 7. Hold Reset Button, Then Click Igniter

Next, press and hold the reset button for a few seconds.

While still holding down the reset button, press and hold the igniter button until you see a flame appear. It is necessary to press the reset button for an additional 20-30 seconds after the flame is ignited to ensure that it is fully functional.

Step 8. Turn Gas Control Valve To “On” Setting

Restore the pilot light by turning the gas control valve back to its “ON” position once it has been re-ignited. Right now, you should be able to keep your house warm!

Step 9. Relax in Comfort

How did things turn out? If not, when will you get your home warm and comfortable? If your pilot light has been struggling to keep a flame, or if you are still unclear how to fire your pilot light, boiler repair is simply a phone call away! Now that you don’t have to struggle with a cold house anymore, you may turn to a licensed professional with your queries and concerns. To arrange a boiler repair, call or go online to this page. With the help of superTech HVAC Services, you can relight your pilot light in no time.

How Do I Prevent My Pilot Light From Going Out?

Keeping your water heater, furnace, and boiler in good working order can keep those annoying pilot lights from going out on you. An experienced technician will do a maintenance check on the pilot light and thermocouple, as well as clean them both, to ensure that they operate at peak efficiency. Depending on the appliance, a professional will also check all of the connected pipes and wiring, the flue venting, and all other functional aspects of the appliance to verify that each portion is running at peak efficiency.

Maintaining your furnace, water heater, and boiler on a regular basis is essential to ensuring that your heat or hot water never runs out!

Soak Up The Warmth!

That’s all there is to it! A basic description of how to relight your pilot light, as well as the most typical causes for your pilot light to go out is provided. We all know that having no heat or hot water in your house is the worst feeling in the world! The best course of action if you’re having difficulties keeping your pilot light lit or are still unclear about the process is to call a professional. If you are experiencing any pilot light issues, please don’t hesitate to contact us at (443) 219-7798 or make an appointment onlinehere.