How to Replace Your Refrigerator Water Filter
- The internal ceiling of the refrigerator
- Inside the refrigerator or freezer’s inside walls (perhaps behind drawers)
- When the door is opened, the frame behind it is visible. In the shadows of the kickplate
- It’s located on the back of the refrigerator.
A sample model number label looks like this:
Your refrigerator’s water filter works tirelessly to ensure that your drinking water is clean and tastes good at all times. It must be replaced on a regular basis in order to maintain its condition; we recommend changing it once every six months. It’s simple to locate your filter and replace it with a new one after you’ve found it. Continue reading to find out how to locate and change your Whirlpool ®refrigerator water filter quickly and efficiently.
Finding and replacing your fridge filter
The first step in replacing your refrigerator water filter is to determine what you already have. See whether it has a serial number printed on it or if it has an authorized water filter for your Whirlpool ®refrigerator Consider purchasing a subscription to have a new filter shipped to you automatically every three or six months once you’ve determined what sort of filter you have.
Select your water filter
Follow the easy replacement instructions described below or watch a video to learn how to change your Whirlpool ®refrigerator water filter. Select your filter from the items listed below to get started.
Filter 1: Step-by-step instructions
- Look inside your refrigerator for the water filter cover, which should be in the top right-hand corner or in the base grille. Open the filter door by lifting it up. Remove the filter and toss it in the trash
- Remove the protective covers from the O-rings on your new filter and set them aside. It is important to check that all of the O-rings are still in place once the lid has been removed. When placing the new filter into the slot, ensure sure the arrow on the filter is facing in the direction of the slot. Do not pressurize the water filter in any way. In case it is difficult to slip into the grooves, twist it until the notches are properly aligned with the grooves. Close the filter door by pressing it down until it clicks into place. Once your filter has been changed, pour four gallons of water down the line to ensure that the new filter is fully flushed.
Filter 2: Step-by-step instructions
- Inside the refrigerator, look for the water filter lid in the top right-hand corner. Open the filter door by pulling it open. Make a slanting motion with the filter, then turn it to the left and pull it. Remove the old filter and throw it away. Remove the protective covers from the O-rings on your new filter and set them aside. It is important to check that all of the O-rings are still in place once the lid has been removed. It is important to make sure that the arrow on the new filter points upward when it is placed in the filter slot for the first time. The filter will begin to rotate as soon as you press it in. Turn the filter counter-clockwise until it locks in place. Close the filter door by pressing it down until it clicks into place. Once your filter has been changed, pour four gallons of water down the line to ensure that the new filter is fully flushed.
Filter 3: Step-by-step instructions
- Look for a little plastic cap that fits over your water filter on the left side of the refrigerator’s base grille. To release the filter, use the eject button on your keyboard. Remove the filter and toss it in the trash
- Remove the protective covers from the O-rings on your new filter and set them aside. After the lid has been removed, check to see that the O-rings are still in place. Place the filter cap on the replacement cartridge in such a way that the ridges are in alignment. To secure the cap in place, turn it counterclockwise. Check to be that the arrow on the new filter is pointing to the left before placing it into the slot. Push the filter all the way in until the eject button pops back out of the filter
- Once your filter has been changed, pour four gallons of water down the line to ensure that the new filter is fully flushed.
Filter 4: Step-by-step instructions
- Water filter cover may be found on your refrigerator inside in the top right-hand corner of the compartment
- If the filter tab on your refrigerator is pointing outward, press down on it and the lid will come off automatically. Alternatively, if you have a tab on the bottom of the cover, you may pull forward and down on the little lever to open it. Pull the filter to the left as you turn it. Remove the old filter and throw it away. If this is your first time installing the filter, you’ll find a cap within the filter slot to help you out. Turn it counterclockwise and pull it out
- It should come out easily. For proper placement of the new filter in the slot, align it with the grooves, push it in, and rotate it to the right. To secure the filter in place, press up on it. Activate the filter door by pushing it up until it clicks shut
- Once your filter has been changed, pour four gallons of water down the line to ensure that the new filter is fully flushed.
Need your model number?
Depending on the model, Whirlpool® refrigerators will show the model number in a variety of locations. Consult our guide to discover where to find yours.
More cleaning tips and tricks
Depending on the model, Whirlpool® refrigerators will display the model number in a variety of ways. Consult our guide to discover where to locate it.
Was this article helpful? Pass it on
This item has been added to the comparison list, which can be found at the bottom of this page.
How to Replace a Whirlpool Refrigerator Water Filter
The water filters in your Whirlpool refrigerator should be updated every six months. Water from the refrigerator may begin to taste odd and seem murky if you leave it for any longer than this. Ice will begin to smell, and you may detect black particles in the water if you leave it for any longer. It is also possible that an out-of-date water filter will have an effect on the water flow, causing water to slowly dribble out and smaller blocks of ice to be generated. Replacement of the water filter in your Whirlpool refrigerator is a straightforward procedure that should not necessitate the use of any special tools or skills.
Installing the incorrect water filter will almost certainly result in the filter not being able to connect to your refrigerator’s main water line.
Step 1: Locate Your Water Filter
The position of the water filter in your Whirlpool refrigerator is determined by the model number of your appliance. The water filter will be situated either in the grille at the base of the refrigerator or within the refrigerator in the top right rear corner, depending on the model. Please refer to your refrigerator’s handbook if you are unable to find where the water filter should be located.
Step 2: Preparation
Put down a towel before removing the water filter in case there is a little amount of water leakage. For refrigerators with filters, you may want to remove any food or beverages that may be in the way before cleaning it out. Replace the water filter when the ice maker is off in your refrigerator. If the ice maker produces ice while you are replacing the water filter, water may run out of your refrigerator. It may be necessary to switch off the water supply to the refrigerator before replacing the filter on some older models in order to minimize water spillage during the process.
When it comes to changing the water filter, it should not be necessary to have access to any electrical components, and therefore it should be safe to do so without disconnecting the power.
Step 3: Remove the Water Filter
It should be possible to remove the old water filter if the water filter is positioned in the grille of your refrigerator. To do so, you should be able to push firmly on the button located to the left of the water filter, which should cause the old filter to be released. If your refrigerator does not have a button to press, twisting the filter counterclockwise by a quarter turn should be sufficient to remove it from the refrigerator. According to the model, you may also need to press in on the filter while spinning it in order to remove the old filter.
There are three options for getting access to the water filter cover: releasing the tab to draw the water filter cover down, lifting the water filter cover, or pressing down on it with your finger.
You should be able to easily remove the old water filter from the refrigerator when it has been freed.
Step 4: Install the New Filter
Whirlpool refrigerators with water filters positioned in the grille include a color-keyed cap that must be unscrewed from the old filter and fitted into the new filter before the refrigerator can be used again. In the event that you have this sort of filter, be certain that the cap has been moved to the new water filter before proceeding. The job of installing the new water filter should be straightforward. Replace the old filter with the new filter by sliding it into the water filter slot on the back of the filter housing.
Make certain that the new filter is installed in the same orientation as the prior filter.
Before continuing, double-check that the filter is securely fastened in place and/or that the water filter lid is closed.
Step 5: Flush Out the System
Before you drink the water, you must first flush the system with water to clean it out and eliminate any carbon fines as well as any trapped air that may have accumulated. It is recommended by Whirlpool that four gallons of water be sent through the system once the filter has been changed. To save time, fill up a one-gallon jug with water and dump it out four times before using it. After you’ve finished flushing the system, you may sit back and enjoy a refreshing glass of freshly filtered water that you’ve earned.
Alternatively, if your refrigerator has a “change filter” light, you may reset it by pressing the button on the refrigerator. You should remember to switch on the water supply again now that the new filter has been fitted if you had shut it off before installing the filter.
How to Replace a Whirlpool Refrigerator Water Filter
Water filters assist to keep the water from your refrigerator or ice tasting pleasant while also keeping the water clean. Whirlpool suggests replacing them every 6 months to ensure that they continue to perform their functions efficiently. To change a Whirlpool refrigerator water filter, just follow the step-by-step directions in this article, which are provided below. Fortunately, it’s a rather straightforward procedure that doesn’t take long to complete. Whirlpool refrigerator models covered include:1ET25DKXGW002-A Y3EAD19XMWR13ECKMF103ECKMF83ECKMF86ED5DHEXWQ00ED5FHEXVL00ED5FHEXVQ00ED5PHAXSB00ED5PHAXSL00ED5PHAXSQ00ED5PHAXSS00ED5PHAXST00ED5PHAXST00ED5PHAX Your first task, if you don’t already have a new water filter, will be to go out and get the appropriate filter, which you may do in person or by ordering them online from a variety of merchants.
Step 1 – Locate Your Water Filter
Depending on the type of Whirlpool refrigerator that you have, it will either be positioned in the grille at the bottom of the refrigerator or within the refrigerator in the right-hand rear corner on the interior of the refrigerator. If you’re still not sure, see your user guide.
Step 2 – Get Prepared
- It is a good idea to lay a towel below the filter in your refrigerator, or on the floor if the filter is positioned outside of the refrigerator, to prevent water from pouring on the floor. In addition, you should take any food or other objects out of the refrigerator so that you may securely access the water filter and remove it. You should switch off the ice maker on your Whirlpool refrigerator while replacing the water filter. There could be an additional step required if your refrigerator does not automatically shut off the water supply when the water filter is removed (most newer Whirlpool refrigerators have this function)
- You may additionally need to turn off the power to your refrigerator. Because you will not be in contact with any electrical components when changing the water filter, you will not be required to cut off the power while doing so.
Step 3 – Remove the Old Filter
- If the filter is positioned in the grille, you may remove it by pressing down on the button to the left of the filter, and you should be able to pull the filter out from behind the grille. If your filter does not have a button on it, you may remove it by rotating it counterclockwise, which should release it and allow it to fall out of the way. It is sometimes necessary to press it in while turning it in order to release it. If your Whirlpool refrigerator has a filter within it, you will first need to remove the cover from it, or in certain models, you may just push the filter up into the fridge. Once the cover has been removed, you simply need to push the button on it and pull it out, or if there isn’t a button, you may push the filter and spin it counterclockwise until it becomes loose, at which point you can pull it out
- The filter can be difficult to remove at times
- If you’re having difficulties, simply press it in harder
- This should loosen it up enough to allow it to be removed. I hope you have been successful in removing the old filter by this time.
Step 4 – Install the New Filter
- Some models will have a cap on the filter that will need to be removed from the old filter and placed onto the new filter
- This will be the case with some models. To install the new filter, first push it into the opening and then turn it clockwise until it is securely in place
- If the filter has a button, you can simply click it into place
- Then, depending on your specific model, you may have to push it in and turn it counterclockwise until it is securely in place
- Always check that the new filter is installed in the same location as the old one
- Otherwise, the installation will fail. You should double-check that it is securely fastened in order to prevent any water leaks from occurring. You should now have a working water filter that you’ve successfully installed.
Step 5 – Flush Out the Water
- Depending on the model, the filter may have a cap that must be removed from the old filter and fitted into the new filter. To install the new filter, first push it into the opening and then turn it clockwise until it is securely in place
- If the filter has a button, you can simply click it into place
- Then, depending on your specific model, you may need to push it in and turn it counterclockwise until it is securely in place
- Always check that the new filter is installed in the same location as the old one
- Otherwise, it will not function properly. You should double-check that it is securely fastened in order to prevent any water leaks from occurring
- The installation of your new water filter should be complete at this point.
Whirlpool Refrigerator Water Filter is Stuck
Clean water filters assist to ensure that refrigerator water remains clear, devoid of odors, and of high quality in terms of flavor. Being vigilant about replacing your refrigerator water filter every six months is a habit that is well worth developing. It goes without saying that discovering your Whirlpool refrigerator’s water filter has become blocked is a major setback to your well-laid plans.
Troubleshooting When Your Whirlpool Refrigerator Water Filter is Stuck
Clean water filters assist in keeping refrigerator water clear, free of odors, and of high quality in terms of flavor. Making the practice of changing your refrigerator water filter every six months is one that is well worth developing. The discovery that your Whirlpool refrigerator’s water filter is blocked is a major setback to your carefully orchestrated preparations.
Quarter Turn Filter in Base
To get rid of the quarter turn filter, do the following:
- Turn the filter a quarter turn to the left—usually, the cap should be positioned vertically—and then turn the filter a quarter turn to the right. remove the filter in its entirety
- Remove the cap from the old filter and replace it with the new one, if applicable according to the model.
If you find yourself stuck, try the following:
- Use pliers to grab the cap and turn it a quarter turn*NOTE: Using too much pressure to create fracture might cause harm to the internal workings of the water system
- Removing the cap with pliers
Image courtesy of Amazon
Push Button Filter in Base
To remove the push button filter, follow these steps:
- Locate the button on the base grille and press it to disengage the filter. Pull the filter out of the grille.
If the water filter in your Whirlpool refrigerator is stuck, try the following:
- To disengage the filter, press and hold the button while the filter is being ejected
- To better access the filter, remove bottom grille and then push button to disengage filter
- To better access the filter, remove bottom grille and then push button to disengage filter, press filter back in and then push button again
Whirlpool is a type of bathtub.
Door Pops Out Filter Inside
To remove the compartment filter, follow these steps:
- In an upward motion, open the water filter compartment door on the left. eject the filter after the door has been completely opened
You can attempt the following if you’re stuck or the whirlpool water filter door won’t close.
- Try the following if you’re stuck or the whirlpool water filter door won’t close.
Image courtesy of Whirlpool
Pull Tab Filter Inside
To uninstall the pull tab filter, follow these steps:
- It is possible to uninstall the pull tab filter by following these steps:
If you find yourself stuck, try the following:
- You can also try the following if you get stuck:
If you’re stuck, try the following:
5 Easy Steps to Change Refrigerator Water Filter
Knowing how to change the water filter in a Whirlpool refrigerator, or any other brand of refrigerator, is rather straightforward. When replacing a filter, make sure you have the correct replacement filter on hand as well as a towel to wipe up any spilled water. Also, go to your owner’s handbook for guidance, since it will have replacement instructions for any brand of refrigerator you may have purchased. This handbook will instruct you on how to replace the water filter in your refrigerator.
However, before changing a refrigerator water filter, be sure that the machine is not currently in operation. Do you want to learn how to change the water filter in your refrigerator? In this post, we’ll talk about how to accomplish your goal! Continue reading to find out more!
How to Change Refrigerator Water Filter
In this section, you will learn all you need to know about how to change a water filter. Also, if you’re seeking for instructions on how to change the water filter in a Whirlpool refrigerator, you may follow these steps.
Step 1: Find the water filter
The water filter is usually found in the bottom of the refrigerator, which is where it should be. Other options include looking at the rear, upper-right-hand corner, or within the refrigerator at the front of the unit for where to find it. When you’ve located it, proceed to the following step.
Step 2: Take out the old water filter from the fridge
The water filter may usually be found near the bottom of the refrigerator, which is convenient. Other options include looking at the rear, upper-right-hand corner, or within the refrigerator at the front of the unit for locating the device. You should go to the following stage once you’ve located the item.
Step 3: Buy A New refrigerator Water Filter
The water filter is often located at the bottom of the refrigerator. Other options include looking at the rear, upper-right-hand corner, or within the refrigerator towards the front of the unit. Once you’ve located it, go to the following step.
Step 4: Get the New Filter Installed
Assuming it is a quarter-turn cap, be certain that it is positioned vertically. Gently insert it inside the filter’s hole using your fingers. Check to see that the water filter is not too tight. Turn the cap in a clockwise direction until it is tightly secured. The filter cap should be adjusted in a line position and gently placed into the device if it is a push-button mechanism. As soon as you place it, the eject knob will appear on the right side of the screen. Get them put into their respective assemblies to replace any covers or cups that came with the filters when they were originally purchased.
Step 5: Label the Water Filter
A quarter-turn cap should be placed in a vertical position if applicable. It should be gently inserted into the filter’s hole. It is important not to overfill the water filter. Make sure to turn the cap in a clockwise direction until it is snug. For a push-button system, adjust the filter cap so that it is in the line position and gently insert it into the unit. The eject button will appear as soon as you place it. Get them placed into their respective assemblies to replace any covers or cups that came with the filters when they were first installed.
How to Change Refrigerator Water Filter at the Bottom of Your Fridge
When using a quarter-turn cap, be sure it is in the vertical position. Gently insert it inside the filter’s opening. Check to see that the water filter is not overly restrictive. Turn the cap in a clockwise direction until it becomes snug. If it is a push-button system, set the filter cap in a line position and gently insert it into the device.
The eject knob will appear as soon as you place it. Get them placed into their respective assemblies to replace any covers or cups that came with the filters. Run a few liters of water through your new filter to ensure that all pollutants are removed.
Step 2: Twist fridge dial to an anticlockwise position to pull it out
Look for the dial that keeps the grill in place beneath the refrigerator’s doors. To unlock it, just spin the dial counterclockwise by a quarter turn to the anticlockwise position. Next, slowly and carefully remove the filter from the fridge until it is entirely removed. Maintain a small towel beneath the filter unit to prevent any water drops (if any) from causing harm to the filter unit. If the filter does not rotate in either way when you press the knob near to the dial, the filter will be released.
Step 3: Slide the Dial Handle onto The New Filter
Look at which way the dial slides at the conclusion of the preceding filter to see whether it was in the correct direction. To remove the dial, pull or push it in an orthogonal direction. Slide your new filter into the dial slot by aligning the edges of its end with the slot on the dial, and then press it until it is secured in place. When you are through with your old one, you may either store it for future use or dispose of it completely.
Step 4: Insert the new filter into its housing and turn it clockwise
Replacing the filter is as simple as pressing the end that connects it to the fridge all the way in until it reaches the “lock” position. In order to lock the dial, spin it 1/4 turn counterclockwise to place it in the lock position. You will be able to use your refrigerator once it has been secured.
Step 5: Change the Filter
If it has a yellow or orange light on, hold down the reset button for three seconds to clear the error. By pressing the reset button, the light will change from yellow to blue or green depending on the setting. Fridges that are more advanced may include a touchscreen menu that allows you to reset the filter. Taking the filter out and re-installing it will resolve the issue if the light will not change colors.
How to Change Twist-On Filters
The twist-on water filter can be found at the upper right corner of a refrigerator; however, some are located in the front section of the refrigerator or within it near the bottom. The following are the actions that you may use to replace Twist-on-Filters.
- Turn the filter 1/4 turn counterclockwise while removing the filter out of the filter housing. Remove the cover from the old filter and replace it with the cover from the new filter
- Afterwards, fit the brand-new filter into its casing and crank it 1/4 turn clockwise to secure it in place
- At the top of the device, towards the rear, is a push-in water filter that may be found by pushing it in. Some are kept in a drawer within the compartment
- Others are placed outside the container.
How to Change a Push-In Filter
- When you release the pressure on a push-in filter, it will alter its configuration. Even if there isn’t a button, merely pushing the filter will remove it. Remove the cap from the damaged filter and replace it with the cap from the new one. Put the new filter into its case by pressing it until it snaps into place
- Then close the case.
How to Change an In-line filter
- First and foremost, turn off the cold water supply. To access the tubing, look for a section of it that is accessible between the refrigerator and the shut-off valve
- Tubing cutters are used to cut tubing for plastic and copper. Afterwards, remove the end cap from the new filter and insert the tubing. Reconnect the water line to the house. Make sure the water has been thoroughly filtered and then check for leaks once the filter has been cleaned.
Tips on Changing Water Filter
Replacing a refrigerator water filter is a simple and quick task that can be completed in a short amount of time. The most fascinating feature of most current water filters is that when you detach the filter, the water supply is cut off automatically, which is a nice touch. It is no longer necessary to manually cut off the water supply when such a function is available. If you are unsure of how to choose the proper filter for your refrigerator, you may take the old one to a nearby hardware store for evaluation.
Final Words
The best strategy to combat hazardous water pollutants is to ensure that your water filters are in good working order. The good news is that when water filters become ineffective, they are simple and quick to replace. Refrigerator water filters are inexpensive and have been shown to improve the quality of water. If you take good care of your water system, you and your family will be able to enjoy fresh and clean water directly from your own home! You should now be aware of how to change the refrigerator water filter if the need arises as a result of this essay.
Is it possible that you have queries about how to change refrigerator water filters in a Whirlpool refrigerator or any other model of refrigerator? If you answered yes, please leave a comment below.
Replacing a Whirlpool (WRS325SDHZ) Refrigerator Water Filter
It is necessary to change the filter in your refrigerator every six months if it produces ice and cold water. This will ensure that your water continues to taste good for longer. The following instructions will walk you through the process of replacing the water filter in a Whirlpool WRS325SDHZ refrigerator. EveryDrop 10383251 is the filter that you will need to have on hand. Finding the location of your refrigerator should be straightforward because the majority of refrigerators have a water line that runs through the cabinets and down to the area below the sink.
- The valve should be turned counter-clockwise until it is unable to be turned any more.
- Drain the water from the cup filler on the front of the refrigerator into a pitcher or a big glass and set it aside.
- 3.Remove the water filter from the system.
- You will notice an arrow on the cap pointing to the right when you flip the book cover down to see it.
- The filter should be able to pull out with ease.
- 4.Install a new filter on your computer.
- Insert a new filter into the mix with the arrow pointing up; then spin the filter clockwise until you hear a clicking sound.
- 5.Finish After you’ve finished installing the new filter, you may turn the water back on.
- Water should be sent through the line for five minutes to verify there is no air remaining in the system.
- If the filter light has not been reset, just push and hold the filter button on the front of the freezer door for a few seconds until it does.
- We, at Jerry’s Appliance Repair, have a team of skilled repair technicians that are ready to come to your location and assist you with whatever you want.
Refrigerator FAQ: How to Change Whirlpool Refrigerator Water Filter
While the water filter in a Whirlpool refrigerator can offer clean, fresh drinking water, it is not designed to last indefinitely. What is the best way to determine whether or not the filter needs to be replaced?
A unpleasant smell or taste in the filtered water might be a typical indicator of a problem. Learn how to change the water filter in your Whirlpool refrigerator using simple steps, how often it should be changed, and how to troubleshoot any issues you may be experiencing.
Why, When, WhereHow to Change Whirlpool Refrigerator Water Filter
Despite the fact that replacing a water filter is easy and basic, not understanding the fundamentals behind it might result in this vital refrigerator maintenance task being overlooked. We’ll go over how to change the water filter in a Whirlpool refrigerator, as well as why it’s required, when it should be done, and where to find the filter.
Do I Really Need to Change my Refrigerator Water Filter?
One of the few methods to assure clean, fresh drinking water is to change the filter on a regular basis. Over time, the particles and impurities that are filtered out by the filter will clog the filter, rendering it unable to perform its intended function. The result is that these contaminants do not pass through the filter and remain in the drinking water. Here’s how to know when it’s time to replace your refrigerator’s water filter:
- The water from the refrigerator has an unpleasant flavor
- A peculiar odor emanates from filtered water. When water is discharged, the pressure of the water lowers.
How Often Should I Replace My Whirlpool Water Filter?
Changing the filter every 6 months should keep bad-tasting water and low water pressure at a bare minimum. However, the frequency with which you should replace your refrigerator’s water filter is determined by the pace at which it flows and how frequently it is utilized. More frequent replacements may be required because to increased usage and quicker flow rates.
How Do I Change My Whirlpool Water Filter?
Water filters for Whirlpool refrigerators can be located in the top right-hand corner of the refrigerator’s interior or beneath the base grille, depending on the model. Others filters are twist-in types, some others are push-in models, and some are both. Check your refrigerator’s use and care handbook to find out where your filter is placed and which kind of filter you need to use with your refrigerator. Here’s how to replace the water filter in your Whirlpool refrigerator in eight simple steps:
- In most cases, the water filter may be found either in the top right-hand corner of your vehicle’s cabin or behind the base grille. The compartment or cover must be opened, which may entail raising the compartment door up or pushing the cover down. Base grille filters may be equipped with an eject button that allows the filter to be removed. Removing and discarding the old filter may need twisting it counterclockwise or pulling it straight out, depending on the filter model. Disassemble the new filter: if the filter contains O-rings, remove the protective cover while making sure the rings are still in place
- Open the new filter
- And test it. Check that any arrows or grooves on the new filter are properly aligned before inserting it into the slot Filters should be secured in place by twisting them in a clockwise direction until they are secure, while others should be pressed in until they are secure. Close any compartment doors and make sure they’re securely fastened in order to keep the filter safe and clear of dirt
- And Dispense and discard 4 litres of water in order to cleanse the filter of any leftover pollutants
- Flush the filter
Whirlpool is the source of this image.
What Do I Do if My Whirlpool Refrigerator Water Filter is Stuck?
Whenever this occurs, first double-check your user handbook to ensure that you’ve followed all of the correct switching steps. Depending on whether the filter is stuck or not, there are various treatments for both the base grille and inside filters. When your base grille Whirlpool refrigerator water filter becomes stuck, use these troubleshooting steps:
- Make certain that any eject buttons are pressed all the way in to completely disengage the filter before using the machine. Twist-in versions should have the filter cap covered with a piece of cloth, and the filter cap should be turned one-quarter turn using pliers.
An internal filter that has been trapped can be resolved as follows:
- Make sure that the water compartment door is entirely open to provide for ample space to remove the filter before starting. It is possible that you may need to remove a refrigerator shelf in order for the door to open correctly. In addition, a buildup of water pressure might make it difficult to remove the filter. Reduce any water line pressure that may exist by shutting off the refrigerator’s water supply and dispensing any remaining water in the line.
Make certain that the water compartment door is entirely open to provide for sufficient space to remove the filter. To allow the refrigerator door to open properly, it may be necessary to remove a refrigerator shelf. An increase in water pressure might also make it harder to remove the filter from the water line. Reduce any water line pressure that may exist by shutting off the refrigerator’s water supply and dispensing any remaining water in the line;