Use These Tips to Drain a Water Heater Properly
Most water heater maintenance instructions recommend that you drain a water heater every six to twelve months, depending on how much use it gets. The reason for this is that it will aid in the removal of any sediment or buildup that may have accumulated on the bottom of the water heater tank as a result of the presence of minerals and other particles in the water. As a result of the accumulation, the water heater will have to work harder to heat the water, consuming more energy and increasing its operating costs.
Before You Begin
Before you begin, make sure you understand where the main water shutdown valve is situated in your home. While you won’t necessarily need it during this procedure, it’s always a good idea to be familiar with this valve whenever you’re dealing with any type of plumbing fixtures in your house in case something goes wrong and you need to shut off all water coming through your pipes.
When doing this procedure, you will be working with water that can be quite hot. It is possible that you will need to switch off your hot water heater many hours before you begin in order to allow the water in the tank to calm down before you begin. If you are unable to do so, use heavy-duty rubber work gloves to protect your hands from any splashes and safety glasses to protect your eyes from any hot water droplets that may fall over them.
- Drain valve (if necessary)
- Threaded hose cap (if necessary)
- Drain valve (if necessary)
Kevin Norris’s The Spruce is a novel about a young man who grows up in the woods.
Perform a Quick Flush
- Using a garden hose connected to the drain valve, attempt to clean the water heater tank a little bit while the water pressure is still on before shutting off the water supply. In order to accomplish this, first open the drain valve for a few seconds before closing it again. The pressure will blast away any silt that has become lodged in the valve, allowing the tank to empty more quickly. If a significant amount of sediment is expelled, you may need to repeat the process several times. Make certain that you’ve connected your garden hose to an outdoor place or into a bucket in order to collect the water and sediment that will be emitted from the faucet. The Spruce / Kevin Norris
- The Spruce / Kevin Norris
Turn Off the Water Heater
- Turn off the gas to your water heater, or turn off the electricity if you have an electric water heater. Remove water by shutting off the valve on the cold-water pipe above the water heater or the main water supply valve to the home, whichever is most convenient. Test the hot water faucets around the home by turning them on and checking for water to ensure that the pressure has been released. Water may flood out at first, but if the water has been cut off properly, it should rapidly decrease to a trickle and then stop. It is important to leave a hot water faucet open in the sink closest to your hot water heater in order to relieve pressure in the entire system. The Spruce / Kevin Norris
- The Spruce / Kevin Norris
Open the Drain Valve
- Open the drain valve while holding your garden hose in one hand. Normally, you may complete this task by hand, but you may need to employ your flat-head screwdriver in this instance. Once the valve is opened, water will begin to rush out of the drain, so make sure your hose is either connected to the outside or to a bucket to catch the water. You should switch off the drain valve as soon as the bucket is full so that you may empty it. Repeat the operation as many times as necessary to completely empty the tank. The Spruce / Kevin Norris
- The Spruce / Kevin Norris
Flush the Tank With Water
- Once the tank has been completely drained, you may flush it with a few gallons at a time by turning on the water for a few seconds and then allowing it to drain out again until it is completely empty. When the outflow is clean, you’ll know that you’ve successfully eliminated the sediment and may proceed to the following phase in the process. The Spruce / Kevin Norris
- The Spruce / Kevin Norris
Refill the Water Heater
- Close the drain valve and remove the garden hose from the system. Make certain that all but one of your home’s hot water faucets are turned off (the one in the bathtub closest to the water heater is best). You may now re-start the water heater by turning the water back on. After that, keep an eye on the faucet you left open and, as soon as you notice that you are receiving nothing but water out of it, turn it off. The Spruce / Kevin Norris
- The Spruce / Kevin Norris
Relight the Water Heater
- Re-ignite the water heater’s pilot light, or if it’s an electric heater, re-energize the circuit breaker. You should be able to use hot water after an hour or so. The Spruce / Kevin Norris
- The Spruce / Kevin Norris
Check the Drain Valve
- Check for leaks at the spout of your water heater to see if the drain on the heater has completely closed. If the outlet does not completely close, you can stop the leak by placing a threaded hose cap over the hose thread of the outlet. Alternatively, you can replace the valve entirely. The Spruce / Kevin Norris
- The Spruce / Kevin Norris
How to Maintain & Drain A Water Heater: 8 Step Guide
Date of publication: December 2019 You may take your water heater for granted until it stops working and you are forced to take a frigid shower in the middle of winter. Even worse, it might cease operating altogether, resulting in water splattered all over the floor. Fortunately, a hot water heater does not require much maintenance, although emptying it on a regular basis may assist to ensure that it continues to operate smoothly. Consider the following recommendations for maintaining your water heater.
According to The Family Handyman, silt builds up in the bottom of a water heater over time, which can cause obstructions in the system.
If you do not properly maintain your water heater, it may not operate at peak efficiency or may even fail to operate at all in some cases.
GET A HOME QUOTE.
A high level of protection for your house makes all the difference when it comes to keeping your family safe. Allstate home insurance can assist you in protecting what is important to you. Request a quote Locate a representative. When it comes to draining a water heater, the DIY Network recommends the following measures. The owner’s handbook for your water heater will provide you with particular information on your water heater. For those who are uncomfortable completing this sort of maintenance on their water heater, contact a plumber to arrange for a professional draining to be performed.
- A water line and a shutdown valve leading into the water heater may be found at the very top of the water heater’s tank.
- Step 2: Disconnect the water heater’s power supply line.
- Alternatively, if you have an electric water heater, turn off the electricity at your home’s electrical panel.
- If you have a gas water heater, according to the DIY Network, you may change the water heater’s thermostat to “pilot” to complete this procedure.
- Check your water heater’s owner’s handbook and follow the directions that are provided for your particular water heater.
- Because your water heater is running at a high temperature, it is incredibly hot.
- (According to BobVila.com, you should at the very least wait a few hours.) In addition, taking a hot shower can assist to accelerate the cooling process.) Step 4: Connect a hose to the drain valve.
Connect the other end of the hose to the drain valve located at the bottom of your water heater.
The hot water tap, such as a sink faucet, that is closest to the water heater should be opened.
According to the DIY Network, it is preferable to use a tap that is located on the floor above the water heater.
As soon as you turn on this valve, the water will begin to drain out of the storage tank.
Step 7: Reconnect the water supply to the tank and flush it with fresh, clean water to finish the job.
It is necessary to repeat this process until the water flows clean.
Step 8: Refill the tank with water.
Return the water supply to its original setting to begin replenishing the tank. Once the tank is full, turn on the electricity or gas supply to the water heater to re-energize it. While draining the tank, remember to turn off the faucet that you had previously turned on.
How Often Should You Drain Your Water Heater?
A good insurance policy may make all the difference when it comes to insuring your house. Allstate house insurance can assist you in protecting what is important to you in your home. Consult for a price Locate a real estate professional. When it comes to draining a water heater, the DIY Network recommends the following steps: The owner’s manual for your water heater will provide you with detailed information on your system. For those who are uneasy completing this sort of maintenance on their water heater, call a plumber and arrange for a professional draining to be performed.
- A water line and a shutdown valve leading into the water heater may be found at the top of the water heater’s cabinet.
- In step two, turn off the water heater’s electricity supply.
- You should turn off the electricity to your home’s water heater if you have one that is powered by electricity.
- If you have a gas water heater, according to the DIY Network, you may change the water heater’s thermostat to “pilot” to complete this task.
- Please refer to your water heater’s owner’s handbook for precise installation and operation instructions.
- Because your water heater is operating at a high temperature, it is quite dangerous.
- You should wait at the very least a few hours, according to Bob Vila.) In addition, taking a hot shower might aid to expedite the cooling process.
As soon as your water heater has cooled down, connect one end of the hose (you may use a garden hose) to a floor drain or, if it is long enough, to the exterior of your home.
Step 5: Run a hot water faucet to warm the water.
Additionally, the tank drains more quickly as a result of this kind of pressure relief.
The drain valve should be opened in step six.
Remember to be patient, as it may take some time for the tank to drain completely if it was completely full or if there is a lot of silt in the tank.
Turn on the cold water again while leaving the drain valve open to assist in flushing out any residual silt from the bottom of the tank.
Once you’ve done that, shut off the water supply valve.
Fill the tank with fresh fuel.
Reconnect the water supply to begin filling the tank. Turn the water supply back on. The water heater’s electricity or gas supply should be turned back on after the tank is full. During the draining process, make sure to turn off the faucet that you had opened previously.
How to Drain a Water Heater
Video Playback is not supported at this time. Every year, draining your water heater eliminates sediment that might cause it to work harder and cost you more money to run the heater.
- The first step is to cut off the electricity or gas to the water heater. After that, close the cold water supply valve, which will prevent water from flowing into the heater. Glue a garden hose to the drain valve at the bottom of the tank and let it flow on the ground outside
- Activate the drain valve that is connected to the hose. Pulling up on the pressure release valve on the tank’s top will allow it to be opened. Allowing the water in the tank to drain is recommended. If there is still sediment in the tank after it has been emptied, open the cold water valve for several minutes to flush it out. Close the drain valve as well as the pressure relief valve and let the tank to fill up again. If the heater is powered by gas, relight the pilot and switch it on
- If your water heater is electric, you’ll need to reset the breaker to restore electricity.
For more information, please visit our video on Water Heater Upkeep and Repair.
- It is critical to drain a hot water heater once it has been plugged with a toilet tank and bowl leak detection kit. How to Check for Leaks in the Toilet Tank and Bowl
How to Drain a Hot Water Heater
Previous PostNext PostWhen was the last time you emptied the water from your hot water tank? When it comes to hot water, we all take it for granted, until it is no longer available. A shivering shower serves as a stark reminder of the significance of regular water heater service. Draining a hot water heater is one of the most important preventative maintenance jobs a homeowner can perform to help extend the life of the unit’s performance. It is important to drain your hot water tank because it reduces sediment accumulation, which allows your water heater to operate more effectively, which can result in cost savings.
Draining Your Hot Water Heater
If you want to empty your hot water heater, you’ll need a length of garden hose that’s 3 to 4 feet long and has a connection that can connect to the drain valve at the bottom of the tank. Many times, this is the same sort of fitting that you use on your water supply line. Plan to direct the flow of the hose into either a bucket or a floor drain, depending on which is most convenient for you and your situation. Turn off the gas and extinguish the pilot light if you’re working with a gas water heater to start the repair process.
Occasionally, it is not essential to completely drain the hot water tank.
Homeowners will also be prevented from accidentally harming their hot water heater by turning it on while there is no water.
- Deactivate the water supply valve that feeds into the hot water tank. Inspect the water heater’s drain valve, which is located at the bottom of the unit. Open the same valve you used before. Make sure that the pressure release valve is open. Allow the water to drain completely. If you aren’t utilizing a floor drain, make sure you empty the bucket on a regular basis. Turn on the water supply valve when the tank is completely depleted. Ensure that the water continues to flow through the tank and through the drain valve until it is clear. Close the drain valve as well as the pressure release valve to allow the tank to fill. In the case of an electric water heater, reset the circuit breaker or reconnect the device. To relight the pilot light on a gas water heater, turn on the gas and relight the pilot light.
While this may appear to be a straightforward procedure, there is the possibility of flooding in your basement if you do not proceed with caution. Plastic hot water heater valves, as well as valves that have not been used in a long time, are susceptible to leaking. Continue to keep an eye on the valve after it has been shut in order to verify that it is not malfunctioning. Even a little trickle might quickly escalate into a major issue.
Professional Plumbing Services
Draining a hot water heater is a simple maintenance chore that many homeowners are capable of performing on their own. In the event that you are not comfortable doing this or would rather to spend your time in other ways, just call your local Mr. Rooter or get a work quote online. Alternatively, If this is an emergency, we are accessible 24 hours a day, seven days a week at 855-591-0128. Whether or not your hot water heater is in good working order, no matter how clean the tank may be, it may be time to consider replacing it.
You may get assistance from the appliance professionals at Mr.
In no way can this blog be considered a substitute for the services of a licensed plumbing professional in your state or region. Before beginning any household improvement, be sure you are in compliance with local and state rules. Previous PostNext Post Previous Post
What Would Bob Do? Draining a Water Heater
Image courtesy of shutterstock.com I’ve just finished draining my water heater for the first time since it was installed in 1989.24 years ago today! I stopped after approximately five minutes since the water came out incredibly clear and there was no trace of any silt. Is this a sign that my heater is devoid of any sediment? Whatever sort of storage tank water heater you have, draining your water heater at least once a year is a good practice. Over time, sediment accumulates within the appliance, reducing its energy efficiency and causing blockages in other fixtures throughout the house, including the kitchen sink.
To remove sediment from a water heater, it is necessary to drain it not just for five minutes, but for as long as it takes for the water heater to entirely empty.
STEP 1: Check the pressure-relief valve.
Before you empty a water heater, make sure it has a pressure-relief valve, which is the device that prevents the tank from exploding due to excessive pressure. You must confirm that the valve is operating correctly in order to do so. Turn off the water heater’s electricity supply. (If the unit is powered by electricity, simply shut it down.) If it is a gas-powered heater, turn it to “pilot” mode to conserve energy.) After that, open the cold water supply line valve by pulling the lever on the valve.
Once you’ve opened the valve, listen for air and look for water to confirm that it’s working.
In addition, if you open the pressure-release valve and nothing happens—no hissing air, no pouring water—it is likely that the valve has to be replaced.
STEP 2: Run your drain line.
Connect a garden hose to the water heater drain and run it to the outside of your house. You’ll most likely need at least two pieces of pipe if the tank is below grade (for example, in the basement). One will go from the tank to a portable pump, and the other will run from the pump to an outside collection container. In most cases, if your water heater is not in the basement, gravity should be able to handle the job. Allow enough time for the water in the heater to cool down (a few hours at the very least) before opening the drain valve to be on the safe side.
STEP 3: Flush your tank.
After you’ve opened all of the hot water taps in your home, you’ll want to open the water heater drain valve as well. In the event that you have opted to utilize a pump, this is the moment to turn it on. Allow the tank to completely empty before turning on the water supply (short bursts of water may help to dislodge any sediment buildup). Make sure there isn’t any silt blocking or slowing down your drain valve’s flow by doing the following: Remove the drain valve, in other words, to allow the sediment to leave through a bigger hole.
Using a long screwdriver or dowel to dislodge silt after the valve has been removed may be beneficial. Keep a number of big buckets on standby to catch any excess water. –
STEP 4: Finish up.
Re-start the water supply after the water flowing out of your tank looks to be running clean once more. Next, close the water heater’s drain valve and switch on the cold water supply to the house. It’s also important to remember to restore the pressure-relief valve to its original position. Close all of the hot water taps in your home (which you had previously switched on in Step 3) and, lastly, reconnect the electricity to your water heater, which should now be clear of sediment after you completed Step 3.
How to Drain a Water Heater (& When You Shouldn’t!)
Homeowners in Birmingham who have classic tank-style water heaters need to know how to empty a water heater properly. This is a vital step in the maintenance of a water heater. You will receive step-by-step instructions on how to do this work yourself from our plumbing pros, as well as information on when you should call a professional and when you should refrain from draining your tank.
How to Drain a Water Heater Tank
Tank water heaters should be emptied about every six months by performing the following steps:
- Make sure that your unit’s electricity or gas is turned off. The cold water supply valve (the valve that delivers chilly water into the tank) should be closed on the unit. Connect a garden hose to the drain valve on the water heater, which is situated towards the bottom of the tank
- Drain the water from the garden hose outside or into a bathtub for drainage. The drain valve should be opened once the line has been fastened and sent outside or to a drain Open the pressure release valve, which is located at the top of the machine. Allow enough time for the water heater to drain completely. When your water heater tank is completely depleted, reopen the cold water valve and allow the water to flow for a few minutes to flush out any remaining particles. Close the drain valve and pressure release valve, then disconnect and empty your garden hose
- To restart the system, turn on the power or relight the pilot light on your water heater.
Why Drain Your Water Heater Tank?
On average, a tank-style water heater sees a large amount of water pass through its tank over the course of a year. While softened water is used in many houses today, certain minerals and sediment are still carried into the water heater — and if you have hard water, your water heater is more adversely affected by higher concentrations of these pollutants. During the storage of water in the tank, silt and minerals fall to the bottom of the tank where they gather. Water passing through them leads them to accumulate over the course of a year, causing troubles for your tank.
- Corrosion of the tank, resulting in both large and tiny leaks
- A reduction in the amount of hot water available
- Popping sounds caused by air trapped in the sediment
- It’s difficult to get water to boil
- Utility bills that are higher
When Not to Drain Your Water Heater Tank
While learning how to drain a water heater isn’t a common home maintenance activity, there are specific situations in which you may not want to do so. The first situation is simply if you are not confident in your ability to carry out this maintenance operation on your own. Leaving water heater repair to a professional is always a wise decision in this circumstance since you don’t want to chance causing any damage to your water heater or causing any water damage to your property. Next, if you’ve never done it before, refrain from draining your water heater!
When sediment accumulates in the water heater tank, hot spots along the bottom metal are frequently created, causing the metal to corrode and eventually fail completely.
If you drain the water heater and remove the sediment all at once, you will almost certainly end up with a leaking water heater.
Get Water Heater Help from Plumbing Experts
Plumbing Experts, a KS Services Company, will assist you with the upkeep and repair of your Birmingham water heater.
Contact us now. Our professional plumbers do complete maintenance on your water heater in order to increase the performance and durability of the unit. Schedule your servicing appointment as soon as possible! prev
Frozen Hose Bib: How to ThawPrevent Major Water Damage
The capacity of hot water tanks is meant to last for many years, but cleaning them should be included in your normal home maintenance program. Following our step-by-step directions outlined below, this is an easy DIY project that you can complete on your own.
Why should I flush my water tank?
The majority of hot water tanks feature a large holding tank, which guarantees that there is always sufficient of hot water available when it is needed. Nonetheless, because the water is left to stay in the tank on a continuous basis for an extended period of time, naturally occurring minerals in the water, as well as sand and grit discharged from municipal water pipes, can accumulate in the tank’s bottom. The accumulation of silt in your hot water tank may make it more difficult for it to perform its function.
Hot water tanks should have a life lifetime of at least 10-12 years, however failing to remove the sediment from the tank on a regular basis can dramatically shorten that life term.
What about my gas hot water tank?
In addition, sediment can reduce the effectiveness of the burner in a gas water heater. Have you ever experienced cracking and popping noises when your furnace was heating up? This is due to the silt that has accumulated in your tank. Sediment builds up in a gas hot water tank, forming a thick, crusty layer on the surface. This reduces the amount of heat that is transferred from the burner to the water in the tank. This is a waste of energy and, more importantly, of your money! In the long run, this can create corrosion in the tank, which may produce a major problem if your tank begins to leak all over your floor.
This will guarantee that your water heater performs at its best.
Can sediment affect my plumbing pipes or water?
Fortunately, the quick answer is “yes!” The sediment or crusty stuff that collects at the bottom of your tank has the potential to break loose and become caught in the pipes that distribute water throughout your home. This might cause the flow of water via your pipes and faucets to become more difficult to control. It also has the potential to clog the drain valve on your hot water tank, making it hard to drain the tank without a major plumbing repair job.
An important word of advice:
If you haven’t cleansed your hot water tank in a number of years, it may be in your best interests to hire a Licensed Plumber to take care of the job on your behalf. You run the danger of causing leaks to be activated. It’s conceivable that the silt that has been accumulating in the tank for years has developed fractures in the bottom of the vessel. The existing sediment is clogging those cracks, however draining and flushing the hot water tank may be able to remove the sediment that is “sealing” the leaks and allowing them to reopen.
The fact that you hired a Licensed Plumber to complete the operation ensures that if it does leak, you’ll be prepared to deal with it immediately.
Speaking from experience.
In the event that you have not flushed your hot water tank in a number of years, it may be in your best interests to have a Licensed Plumber perform the task for you. Activating leaks is a possibility if you do so. This might be due to years of silt buildup in the tank’s bottom, which could have caused cracks to appear there. If any fissures exist, the existing sediment is closing them up; however, if you dump and flush the hot water tank, the sediment that is “sealing” the leaks may be flushed away.
You’ll be prepared in the event that a leak occurs since you’ll have hired a Licensed Plumber to take care of it as soon as it happens.
One important first step
The first step is to identify where the drain valve is located on your tank. It has the appearance of a little outside faucet. Before draining your hot water tank, we highly advise that you cut off the gas or electricity to the tank and let the water drop to room temperature before draining it. It will take several hours to complete this task. This is not required in order to drain your tank, however it is recommended as a safety measure. If you do not want to wait the appropriate amount of time for all of the water in your water heater to cool, just keep in mind that the water that comes out of the drain valve will be extremely hot when it does.
Steps to Draining Your Hot Water Tank
- Turn off the gas or electrical power to your hot water tank if it is connected. The “pilot” setting on a gas water heater is what you’ll want to use. If the water heater is electric, turn off the breaker or unplug the fuse located at the electrical panel
- Turn off the cold water supply valve located at the top of the water heater
- And turn off the gas supply valve located at the water heater. When you touch this pipe, it should be ice cold. If the valve feels warm to the touch, you’ve got the incorrect valve. Locate the tank drain valve, which should be towards the bottom of the tank, and connect a regular garden hose to the drain valve. Keep in mind that certain models may have a cover over the valve opening
- The other end of the hose should be placed in a floor drain or on a driveway where it may safely drain. Buckets can be used if required, but take care not to be burnt by the hot water while you’re doing your task. To prevent this from happening, make sure the hose’s end is lower than the water tank’s valve. Locate the hottest water tap that is closest to the water heater, preferably on the second or third story above. Opening the drain valve and allowing the water to flow from the tank can relieve pressure in the system, similar to withdrawing your finger from the top of a drinking straw loaded with liquid
- Close the drain valve and let the water to drain from the tank. Once again, if you haven’t allowed the water to cool before using it, proceed with caution. Once all of the water has been emptied from the tank, switch on the cold water supply to the tank for a limited period of time. This will help to stir up any silt that has accumulated. It is necessary to repeat this procedure until the water flows clean
- Disconnect the drain line and switch on the cold water supply valve after closing the drain valve. The tank will begin to fill as soon as possible. Return to the hot water faucet that was previously opened. Once cold water begins to flow from the faucet, cut off the water supply. Return the gas valve to the on position from the pilot position, or reconnect the power to the tank. It is important to double-check the valve opening once it has been closed to ensure there are no water leaks.
What if my tank won’t drain?
If your hot water tank is draining slowly or not at all, open the temperature and pressure relief (TPR) valve on the hot water tank to see if it helps. In the hot water tank, it’s at the top where you’ll find it. A pipe goes from the top of the tank to the bottom of the tank, and it’s normally operated by a lever that may be raised or lowered as needed. Opening the TPR valve may allow water to drain from the tank if there is a possible vacuum inside the tank that has been preventing it from doing so.
The most prudent course of action is to contact a Licensed Plumber in this situation.
To sum things up.
Despite the fact that it is one of the most often used items in your home, the hot water tank is also one of the most ignored. If you follow the methods outlined above, maintaining your hot water tank will be a simple chore. If you prefer that our Licensed Plumbers handle the maintenance on your hot water tank, please contact us at 905-259-3344 to make arrangements.
Your Guide to Draining a Water Heater
How to Drain a Water Heater in One Quick Step
- Step 1: Turn off the water and the water heater. Step 2:Connect the hose to the drain location. Step three: Inspect the pressure relief valve. Step 4: Turn on the hot water faucets. Step 5: Turn on the drain valve. Step 6: Empty the tank. Step 7: Fill the tank with water and switch on the water heater.
When it comes to your house, the basic water heater is bit of an unsung hero. Despite the fact that it operates around the clock and out of sight, it ensures that you may take lengthy, hot showers and wash your dinner dishes in warm, sudsy water. All it seeks in return for its devoted service is a little fee. Cleaning up after yourself every now and again. This Might Also Be of Interest to You: What is the proper way to turn on my water heater? Fortunately, it’s a simple job that can be completed with only a few simple instruments.
However, because your water heater is (clearly) bursting at the seams with hot water, it is critical that you proceed with caution while you complete this procedure. Learn how to empty your water heater in a safe and effective manner.
Know When to Drain the Tank
Natural minerals found in your home’s water supply might accumulate at the bottom of your water heater tank over time, causing it to malfunction. Because that sediment can impair the effectiveness of the heater, limit its life, and even cause blockages, keeping it cleansed is a good idea. Experts recommend that you wipe away the sediment around once a year, according to the experts. Part of determining when to do it will depend on how hard your water is and whether or not you’re linked to a municipal water supply where sand and grit may find their way into the water supply.
How to Drain a Water Heater
The first step in this project is to make sure that your water heater is turned off before you begin. With a gas water heater, you may accomplish this by setting the knob to “pilot.” The circuit breaker that controls your electric heater must be found and turned off in order to prevent damage to the heater from occurring. Typically, the water heater is protected by a separate circuit breaker. It will be necessary to turn off the cold water that feeds into the tank as well, which can be accomplished by twisting a knob located at the top of the tank in the opposite direction.
Step 2: Run the Drain Line to a Good Draining Location
In order for the water within the tank to be able to depart, you must first provide a passage for it. As long as your water heater is elevated or located on a higher floor of your home, the process of draining the water heater can be as simple as connecting the heater to a safe draining position outside your home. If the water heater is located below grade, such as in a basement, you have two options to consider. Use a bucket to collect the water, or you may purchase a pump and attach a hose line to pump the water up and out of the hole.
Step 3: Check Your Pressure Relief Valve
In order for the water within the tank to be able to escape, you must first provide a passage for it. As long as your water heater is elevated or located on a higher floor of your home, the process of draining the water heater can be as simple as connecting it to a safe draining position outside. It is possible to use two different options if the water heater is below grade, such as in a basement. Use a bucket to collect the water, or you may purchase a pump and attach a hose line to pump the water up and out of the house.
Step 4: Open the Hot Water Faucets in Your Home
Start all of your hot water taps in your house at the same time to alleviate even more pressure in the tank and aid in its emptying.
If you want, you may just turn on the hot water tap that is nearest to the tank. Additional Related Articles:
- How to Relight the Pilot Light on Your Water Heater
- Don’t Forget to Flush the System! The following is a 6-Step Guide for Flushing Your Gas or Electric Water Heater: What is a Smart Water Heater and how does it work? Find out how much it will cost to replace a water heater
- Whether a tankless water heater is worth the investment.
Step 5: Open Your Drain Valve
Prepare your bucket or pump system, and then release the drain valve located towards the bottom of the tank to allow the water to drain. A built-in knob is normally available for this valve, however it is occasionally necessary to put a flat-head screwdriver into a slot and turn it counterclockwise to operate it properly. It is at this moment that water will begin to pour out of the tank in large quantities, so be prepared to collect or redirect it as soon as possible. In order to empty your bucket, you can shut off the valve whatever many times you need.
Step 6: Flush the Tank
However, even though much of the sediment will be removed simply by draining the tank, it’s always a good idea to check that your water heater is completely clear of sediment by flushing it with cold water. To do so, just turn the cold water knob at the top of the tank back on and let it run until the water drains completely out of the hose linked to the drain valve, which should take around 15 minutes. If the water flow stops at any time throughout the draining process, you’ll want to remove the hose and use a tiny screwdriver or awl to scrape away any debris that may have accumulated in the output.
Step 7: Refill the Tank and Turn It Back On
Remove the drain knob from the water heater once it has been completely cleansed and the output is flowing freely again. Ensure that you close your pressure release valve if you had previously opened it. Then, reconnect the cold water supply line at the top of the tank by turning it back on. Make your way to the hot water spigots that you previously unlocked and wait for the water to start flowing through them. When this occurs, you will be able to turn them off. Depending on the type of water heater you have, you will need to either turn the electricity back on or the gas back on.
How to Flush or Drain a Water Heater
Remove mineral sediment and scale from your water heater tank twice a year by flushing it out. Your water heater will heat more effectively and last longer as a result of this improvement. This professional advise demonstrates how to flush and drain a water heater through the use of videos, pictures, and easy-to-understand language. What is the significance of flushing or partially emptying a water heater? For the simple reason that it reduces the accumulation of mineral deposits within the water heater.
- A very thick, crusty layer can grow at the base of a gas water heater, and the heating components of an electric water heater can be completely covered by these sediments.
- It eventually results in rusting as well.
- They can also block the valve that is used to flush or drain a water heater tank, causing it to not function properly.
- The hypothesis goes like follows: A small crack in the base may have filled with silt, which can assist prevent leaks, especially in a gas water heater where the flame has been roasting the steel bottom.
- In the event that your water heater has not been cleaned in several years, it would behoove you to consult with a few of plumbers in your neighborhood for their recommendations.
- Flushing or partly draining a water heater at least once a year from the time it was initially installed is the most prudent approach to follow in this situation.
- If you decide not to undertake the repair yourself, you could expect to pay a plumber between $80 and $100.
- Diagrams of Electric and Natural Gas Water Heaters It is necessary to drain a water heater tank in order to replace or repair it, as well as to remove mineral deposits from the tank, through the drain valve located at the bottom of the water heater.
The drain valve looks like a little outdoor faucet. If you use this valve, keep in mind that the water will be hot until the water has had time to cool before the water is released. In a nutshell, here’s how to flush or empty a water heater on your own:
- The water heater’s gas or electricity should be turned off. Close the cold water inlet valve and turn it off. Connect a hose to the water heater’s drain valve and run it to the location where the water will be drained
- Open a hot water faucet in a convenient location around the house. Open the water heater drain valve (caution: hot water will be released! )
- Close the valve after flushing 3 to 4 gallons (if draining, continue until the tank is empty)
Please continue reading for additional information on these processes.
How to Flush or Drain a Water Heater Tank
Listed below are the procedures to be followed while flushing or emptying a water heater. This video provides a wonderful summary of the subject: To turn off the gas or electrical power to the water heater, depending on whether it is a gas or an electric water heater, follow these steps: The “Pilot” setting on a gas water heater is as simple as turning the gas control to “Pilot.” 2 Turn off the cold water inlet valve, which is responsible for regulating the supply of water into the tank.
- Make certain that this is the incoming cold water valve and not a valve for the outgoing hot water supply (the pipe should be cold).
- The supply to this water heater is controlled by a lever valve.
- 3 Using a hose, connect it to the tank drain valve, which is located in the bottom of the water heater, and direct it to a drain, the outdoors, or a large bucket.
- Fill the tank with water by connecting a hose to the water heater’s drain valve.
- As the water drains, this prevents a vacuum from building in the system.
- To avoid scorching, exercise extreme caution.
- 5Depress the drain valve on the water heater.
Once this is done, close both the drain valve and the PT valve.
In the event that you are totally draining the water heater, leave the drain valve open until the tank is completely empty.
7Refill the water heater with fresh water.
Return the water supply valve to its original position to re-fill the tank.
Then, reopen the hot water faucet to allow any remaining air to escape from the tank and pipes.
Allow the water to clear for a few minutes before turning off the faucet. 8Restart the water heater if necessary. If you have a gas water heater, relight the pilot light, or switch on the electric circuit if you have an electric water heater.
Water Heater Won’t Drain
If your water heater is draining slowly or not at all when you open the drain valve, you should try opening the pressure-relief valve to see if it helps (see the illustration at the top of this page). This has the potential to dislodge the vacuum that is keeping the water from leaving. In most cases, if the water heater won’t drain or drains slowly, the problem is most likely due to an excessive amount of sediment building up in the water heater. The drain valve of a water heater can become clogged with sediment.
First Steps in Breaking a Drain Valve Clog
1Detach the water heater from the mains. Depending on whether the water heater is gas or electric, switch off the gas valve or the circuit breaker that supplies electricity to the water heater. Secondly, connect an outside hose to the drain valve and run it outside, making sure that the hose’s end is below the level of the water heater. Turn on a hot water faucet someplace in the home or open the pressure-relief valve on the water heater to dislodge the vacuum that has built up inside the tank.
If the water flows freely, the valve is functional.
4 In the event you believe that the drain valve has become clogged, you can attempt to shoot water and air bubbles back into the tank by repeatedly walking on the hose a few feet away from the tank.
If it does not, continue reading.
How to Back-Flush a Water Heater
A hose is connected between the drain valve and an outdoor faucet, and water is squirted back into the water heater through the drain valve in order to backflush it. For this project, you’ll need two male threads connected together with a double-female garden hose coupler (which can be purchased online for approximately $8).
How to Flush a Water Heater Video
Take a look at this video, which demonstrates the procedure of cleansing your hot water heater.
Back-Flushing a Water Heater Step-by-Step
1First, perform the steps outlined above for preparation. 2Close the drain valve on the water heater by twisting it in the clockwise direction. 3Connect the male end of the garden hose to an outdoor hose faucet or a washtub faucet by means of the female hose coupler that was previously installed. Hose Coupler with a Double Female EndBosch4 Turn on the faucet to fill the hose with water pressure and fill the hose with water. 5Depress the drain valve on the water heater. A torrent of water should be forced into the water heater, forcing deposits away from the water heater’s valve.
7Remove the hose from the water faucet and attempt cleansing the tank once again with the hose. If the water heater’s drain valve is still not functioning properly, the next step is to either replace the drain valve or to replace the water heater.
How to Replace a Water Heater Drain Valve
As previously noted, flushing a water heater is a vital element of doing basic DIY water heater maintenance. Unfortunately, the drain valve on a water heater can get blocked with mineral deposits to the point where it must be completely replaced. Step-by-step instructions on how to replace it may be found here. Valve for the drain of a water heaterB K Water heater drain valves are available for purchase at most hardware stores and on the internet for around $8 per valve, depending on the model.
- Water heaters have a drain valve that is positioned at the bottom of the tank.
- Having a helper use buckets to collect and dump water that is flowing from the water heater while you remove and replace the valve will be the norm in most circumstances, but it may be necessary in other cases.
- Expect to be drenched as a result.
- This will take some time.
- To do this, switch off the cold-water supply to the water heater and ensure sure no one comes into contact with any of the hot water fixtures or appliances in the house while the valve is being changed.
- After that, turn off the circuit breaker on an electric water heater or the gas valve on a gas water heater to prevent the water from reheating further.
- Allow for the water in the water heater to drop down to a safe temperature before using it once more.
Before you begin the task, make sure you have two buckets, a pipe wrench, a screwdriver, and the new valve on hand to make the job easier.
Wear leather-palm gloves and have a helper as well as lots of rags on hand before you begin.
The water will begin to seep as the seal loosens, then spray, and ultimately pour warm (or hot) water!
Remove the valve completely from the system.
Insert a screwdriver into the hole and move it around to break up any deposits that have accumulated.
Disconnect the tank’s water supply with a hose until the water begins to flow clean of sediments.
In addition, if you’ve opened the water heater’s pressure-release valve or any hot water taps, make sure you close those as well.
8 In order to restart an electric water heater, turn the circuit breaker back on, or open the gas valve and ignite the pilot (or use the electronic ignition) in order to restart a gas water heater, following the manufacturer’s instructions.
Now is the time to request free quotes from area professionals: 1-866-342-3263
How to Drain a Water Heater
As previously said, flushing a water heater is a vital element of doing basic DIY water heater maintenance. Because of mineral deposits, the drain valve on a water heater might become completely blocked, necessitating the replacement of the valve. Detailed instructions are provided on how to replace it. The Drain Valve on a Water HeaterB K Water heater drain valves are available for purchase at most hardware stores and on the internet for around $8 per valve. Most people choose 3/4-inch as the most common size.
- Don Vandervort of HomeTips.com says: The chance of flooding your basement increases if you do not first empty the water heater and then replace its drain valve, unless you have a floor drain nearby.
- When you’re ready to begin the valve repair, have a buddy on hand to collect water in a bucket while you remove and replace the valve.
- For now, though, you will need to let the water to cool before draining it partially from the tank using hot water taps throughout the home.
- For this, switch off the cold-water supply to the water heater and ensure sure no one comes into contact with any of the hot water fixtures or appliances in the house while the valve is being replaced.
- Next, disconnect the circuit breaker from an electric water heater or the gas valve from a gas water heater so the water does not heat up again.
- Allow for the water in the water heater to get down to a safe temperature before using it once it has cooled.
- Before you begin the task, make sure you have two buckets, a pipe wrench, a screwdriver, and the new valve on hand.
Protect your hands with leather-palm gloves, and be prepared with a helper and lots of rags.
With time, it will start leaking, then spraying, and eventually dumping warm (or hot) water!
Completely remove the valve.
In order to break up deposits, insert a screwdriver into the hole and wiggle it around.
5 5Test the new drain valve by opening and closing it a couple of times.
6Close the drain valve and remove the plug.
7Then, to replenish the tank, turn on the water supply valve.
Make the following phone call to get free estimates from nearby contractors: 1-866-342-3263
How to Flush a Water Heater:
- To begin working on your water heater, make sure that all of the electricity to the device has been turned off, including the circuit breaker. Immediately turn off the cold water supply and wait a couple of hours for the heater to cool (this may take many hours). Locate the drain valve on your water heater, which is usually located at the bottom of the tank. It is possible to drain the water from the tank without using the floor drain by using a conventional garden hose and connecting it to the valve. The water will be directed into a bucket. Although many people may simply use gravity to drain water from the device into a bucket, following the manufacturer’s connection instructions is recommended if you wish to pump the water outdoors (which makes disposing the unwanted water easier). In order to avoid damage to your pipes, open one or two hot water taps around the home. Drain the water and look for silt by opening the drain valve. if the water is turbid or cloudy, refill the heater with fresh water and drain it once again Turn the water shut off valve on and off a couple of times to mix up any sediment that has accumulated at the bottom of the tank
- Continue to fill and empty the heater as often as required until the water flows clean. If the unit is in good condition, one flushing is usually sufficient, and you will not need to flush it again for at least one year. It may be necessary to consult with a specialist if there is an excessive quantity of sediment in your water. Once the water flows clear and the unit is completely empty, remove the hose and pump from the unit. Close the drain valve and replenish the tank before turning on the water heater’s power source. Turn on the water heater’s power source. Performance should return to normal, with the exception of a few air pockets that will be expelled via the faucets at the beginning. In most cases, the air will be expelled within a few seconds, and then full water flow will be restored to the system. Close all of the water faucets that you have previously opened.
How to Tell if Your Water Heater Has Sediment Build-Up
There are a number of symptoms that your water heater has a sediment build-up, including the following ones:
- Despite the fact that energy use has not increased, energy costs have grown. The hot water runs out before it should
- When the water heater is operating, it generates a lot of noise. Your hot water appears to be rusted or has a foul odor
- It takes an extremely long time for the hot water to come to temperature
- There is inconsistency and fluctuation in the water temperature.
Draining a water heater is a relatively simple task that most homeowners can complete on their own. However, if the water does not drain or if the heater’s performance issues persist after flushing the unit, a professional will be able to identify other potential problems that may not be apparent to the homeowner.