How To Clean Katadyn Water Filter

Water Filter Maintenance

Proper cleaning after usage and before to long-term storage is an important component of ensuring that your water filter performs to its maximum potential. It’s possible to treble or quadruple the service life of your new filter by being gentle with it—not to mention helping it filter more effectively. Most filters come with detailed cleaning and maintenance instructions from the manufacturer, which we recommend that you follow to the letter. The following is an overview of the normal methods, along with tried-and-true field suggestions to help you get better outcomes.

Choose quiet pools rather than flowing currents; rushing water stirs up sand and debris, making them more difficult to find.

Allow the muddy water to settle: Remove a potful of water from the heat and set it aside to allow the suspended particles to settle out; an hour or two would enough, but leaving the water overnight is preferable.

More: With Gear 360, you can browse gear reviews written by people just like you.

  • Simply disconnect the intake hose and connect it to the filter outlet on the filter.
  • A diluted bleach solution is normally used to sterilize the filter element after it has been backwashed or before it is placed in storage.
  • It is important to follow the manufacturer’s guidelines since scrubbing a filter that was not meant to be washed may cause it to lose its integrity.
  • To ensure that the element is clean after each trip, flush it with a diluted chlorine solution made by mixing 1 capful of household bleach with 1 quart water, unless the manufacturer specifies otherwise.

Will Bleach Hurt A Katadyn Hiker Filter?

D SBPL Member@smoke e-mail address There looks to be some blackish mold on the surface of a Katadyn Hiker filter cartridge I’m using. I’m going to think that it was stored damp. I had intended to soak it in a strong bleach/water solution for a while. Will this damage the charcoal component of the filter or cause it to malfunction in any other way? Yes, bleach will be absorbed by activated carbon, maybe to the point where the carbon’s efficiency is entirely reduced if a large concentration is utilized.

  1. A bleach wash through my is something I do every now and then.
  2. I just add about 1 oz of bleach to a liter or two of water and pump it through a couple of times before allowing it to soak for about an hour.
  3. It’s effective for me.
  4. No matter how long you soak the system in bleach, I’m not sure whether it makes a difference in the quality of the result.
  5. Roger Caffin is a Canadian businessman.

Mild bleach should be used, followed by thorough flushing. Cheers When I had one, I would clean it well with a light bleach solution before storing it away. After you’ve finished with the bleach procedure, it’s critical that you allow it to dry completely.

Quick Answer: How To Clean Katadyn Water Filter Hiker

A 750-liter test (without a filter protector) revealed that the Katadyn Hiker Pro was successful in removing bacteria (Klebsiella terrigena) and protozoan cysts from the water (Giardia and Cryptosporidium). For optimal performance, the cartridge should be replaced after 750 liters of use or when the machine becomes difficult to use.” The 22nd of October, 2012.

Can you backflush a katadyn BeFree?

To use the BeFree Water Filter with a bigger squeeze bottle, you’ll be limited to using it with the HydraPak 2L or 3L Seeker Soft Bottles, which are both available from HydraPak. In contrast to other hollow fiber water filters, the BeFree Water Filter cannot be backflushed with the use of a syringe, and a syringe is not supplied with either the filter or the water bottle system.

Does Katadyn Hiker and Hiker Pro use the same filter?

Modern water filters, on the other hand, allow you to drink from virtually any source of water. Katadyn Hiker, one of the most dependable devices on the market, has long been the go-to water filter for most hikers over the past few years. Which one has a better filtration mechanism, and how do you know? Katadyn Hiker is a young woman who enjoys hiking. Katadyn Hiker Pro Filter Type Pump Katadyn Hiker Pro Filter Type Pump Katadyn Hiker Pro Filter Type Pump Katadyn Hiker Pro Filter Type Pump Katadyn Hiker Pro Filter Type Pump Katadyn Hiker Pro Filter Type Pump Katadyn Hiker Pro Filter Type Pump

How often do you need to replace Katadyn filter?

Katadyn recommends that the components be replaced after 6 months of continuous usage. When the filter elements are thoroughly dried out after usage, the service life of the filter elements can be extended. For up to 50,000 litres, the ceramic pieces will continue to eliminate germs from the water (13,000 gallons).

How do you clean a hiking water filter?

To clean the cartridge, carefully remove the netting and the Filter Protector from the base of the cartridge. Clean the Filter Protector by placing it on a flat surface and using a moist sponge or rag. Reinstall the device after rinsing it with water. Cleansing the filter cartridge is also advised, which may be accomplished by holding it by the top and “swishing” it in water.

Do katadyn filters expire?

Many hiking water filters have reached the end of their useful life or are no longer functioning properly. One should be changed at the very least every 2 to 6 years, according to a decent general rule of thumb.

Does Sawyer squeeze expire?

Is the Sawyer MINI a limited-edition model? The Sawyer MINI does not have an expiration date, and it is available indefinitely. Afterwards, you’ll need to sterilize it by backflushing it with bleach and allowing it to dry fully before you can put it away.

Does katadyn remove viruses?

In general, the Katadyn Pocket filter is exceptionally long-lasting and reliable. In order to eliminate all bacteria and protozoa as well as other impurities bigger than 20 microns, the filter must be able to filter down to 0.20 microns (see our particle size chart here). Viral and other micro-organisms smaller than will “NOT” be removed by this method.

How much does the Sawyer squeeze weight?

3 oz Water Treatment Sawyer Micro Weight 2 oz / 57 g Type Squeeze/Straw 3 oz Water Treatment Sawyer Micro Medium Hollow fiber with dimensions of 2 x 5 in / 5 x 13 cm.

How much does a Sawyer mini weigh?

The Sawyer MINI is Sawyer’s lightest and most versatile personal water filtration system. Weighing only 2 ounces and fitting in the palm of your hand, the Sawyer MINI provides 0.1 micron absolute filtration, removing 99.99999 percent of all bacteria, including salmonella, cholera, and E. coli, from your drinking water.

How do you use micropur tablets?

Micropur pills can be used on their own with clean water, or in conjunction with a filter if the water is murky or contaminated with bacteria. In a litre of clear water, dissolve a tablet by dissolving it in it for 10 minutes. Shake thoroughly, then let it sit for another 20 minutes before using the water.

Can you freeze katadyn BeFree?

THE FREEZING | The Katadyn BeFree hollow fiber water filter, like other hollow fiber water filters, can freeze if left out in freezing conditions for an extended period of time — this effectively destroys the filter. There is no way to know if your filter has been corrupted or not without disabling it completely.

How does a BeFree filter work?

Simple as that: fill the bottle halfway, screw in the filter, turn the bottle upside down, and squeeze! When the water is fresh, or pure, it runs through the filter at a surprisingly quick pace, even faster than the Sawyer, another filter that we use very frequently. The BeFree, according to Katadyn, can filter up to two liters of water per minute.

Is Katadyn filter safe?

The Katadyn Hiker Pro is a classic and dependable hand pump that has stood the test of time. It removes germs as well as protozoans such as Giardia and Cryptosporidium, making it an excellent backpack filter for North America’s wilderness areas.

Does Katadyn filter Giardia?

In addition to being 99.99 percent successful in removing dangerous bacteria and protozoa such as E.coli and Giardia, the BeFree is also inexpensive.

How long are MSR filters good for?

The length of time a filter will endure will differ significantly from one water source to the next. The ceramic element has a life expectancy of up to 2000 liters.

How do you dry Sawyer squeeze?

Afterwards, you should filter part of the bleach water via a sieve or funnel. After that, put the cap back on or close the filter cap and let the filter to set for an hour before using it. When the hour is over, drain the bag and let everything to dry completely.

Did katadyn buy pur?

Afterwards, you should filter part of the bleach water via a sieve. Once you’ve done that, replace the cap or close the filter cap and let the filter to set for an hour. When the hour is over, drain the bag and set it aside to dry.

Do water filters go bad if not used?

Do water filters that haven’t been used expire? No, water filters that have not been used will not expire. Water filters have an indefinite shelf life as long as they are not exposed to any moisture or other contaminants. Moisture is essential for water filters to function properly, and without it they’ll just sit there looking lovely and ready to be used whenever the need arises.

How do I know if my water filter is bad?

The following are 8 signs that your refrigerator’s water filter needs to be replaced (and how to replace it). 2 Ice has a strange odor to it.

Slow trickle of dispensed water is shown in the third image. 4) The Ice is Coming Out in Pieces. 5) The presence of black specks in water or ice. 6) The Water Filter Light is illuminated. 7) The appearance of water or ice is murky. 8) It’s been more than a year since the last time we spoke.

How often should you change water filter cartridge?

Water filter systems are often shipped with explicit instructions on how frequently to replace the cartridges in the filter system. The frequency of replacement varies depending on the type of cartridge used, but in general, cartridges must be replaced every 3 to 6 months.

See also:  How To Hide Water Heater In Laundry Room

Do MSR water filters expire?

The MSR SweetWater filter will always be in good working order, regardless of the time of day or night until the following day. Every time you use it, you must thoroughly rinse and brush it clean. You are gradually “degrading” the filter element with each brushing action you perform. When you can see the “Diamond mesh,” it’s time to replace your current mesh.

How long does a water purifier last?

Generally speaking, most water filters last anywhere from 6 to 12 months before they need to be updated, depending on usage.

Katadyn Hiker pro Filter question

WhiteBlaze Pages is scheduled to launch in 2022. A Comprehensive Guide to the Appalachian Trail. $5 for a printed PDF, which is AVAILABLE RIGHT NOW. $9 for a PDF that is interactive (smartphone version) More information may be found here. Store for WhiteBlaze Pages

  1. 06-13-2010,07:011 Registered User
  2. 06-13-2010,07:011 Date of joining: January 25, 2009Location: Wheeling, West Virginia Age55Posts80

Katadyn Hiker pro Filter question

  1. How frequently is it recommended that the water filter in the Hiker Pro be changed? I’ve been cleaning out my filter at home and observed that the bottom half of the filter is blackish and the top half is still clean looking after rinsing it a several times. Is this normal? So far, I’ve probably put around 10 gallons of water through the system since I got it a few years ago, if that. Yes, every time I return home from a trip, I clean and dry the filter in my car. I’m just interested because I can’t seem to find my way around anymore
  2. 06-13-2010,08:582Registered User
  3. Joined on June 13, 2010
  4. 07-09-2007 LocationHowell, MIAge65Posts452Images4 Use the cleaning pad that came with the filter to thoroughly clean it. Lightly scrape the exterior surface of the filter, concentrating on eliminating the black areas
  5. Otherwise, you will reduce the life of the filter. 06-13-2010,09:453Registered User
  6. Join Date: 06-13-2010,09:453 The date is January 25, 2009, and the location is Wheeling, West Virginia. Age55Posts80 Thank you, walkingstick
  7. Everything else appears to be in order. 06-13-2010,13:054Registered User
  8. Join Date: 06-13-2010,13:054 Date: December 26, 2004Location: Thompson Station, TNAge: 61Posts410 bycrazyonelost, first published on How frequently is it recommended that the water filter in the Hiker Pro be changed? I’ve been cleaning out my filter at home and observed that the bottom half of the filter is blackish and the top half is still clean looking after rinsing it a several times. Is this normal? So far, I’ve probably put around 10 gallons of water through the system since I got it a few years ago, if that. Yes, every time I return home from a trip, I clean and dry the filter in my car. I’m just interested since I can’t seem to find my way back to my apartment. Mold or more likely mildew forming on the filter element might be the source of the problem. My question is, do you put the filter back together once it has been cleaned and “dried”? If this is the case, then there is an issue. I’ve arrived to this conclusion by considering my own and other Hiker users’ experiences, as well as conversing with representatives from the firm itself. For those who do not use their filters on a regular basis and who clean and store their filters after returning from a trip, it is recommended that they keep the filter and the element separately. If you store the filter in its constructed state, any moisture that accumulates in the filter body will result in a mold problem. I’ve even tried drying over heating vents, hair dryers, and other methods, but it’s impossible to entirely dry the body or the element in order to avoid some bacteria from growing. I also make use of some of the little desecant packets that come in certain food and meal storage containers. To see if it is simply a matter of dirt in the filter, place a coffee filter over it and secure it with a rubber band to ensure that your filter element lasts as long as possible. Also, make an effort to obtain water from a source that is neither sandy or brackish in nature. Using a water container to collect water from a spring or source is one of the things I’ve learned over the years. Then, when I go back to camp, I hang that container and allow it to sit and filter from the top for a time. This enables me to have a ready supply of water for drinking and cleaning purposes at my campground
  9. 06-13-2010,13:085Registered User
  10. Join Date: 06-13-2010,13:085 Date: December 26, 2004Location: Thompson Station, TNAge: 61Posts410 Here is the water bag to which I was referring: 06-13-2010,13:226Registered User
  11. Join Date: 06-13-2010,13:226 The date is January 25, 2009, and the location is Wheeling, West Virginia. Age55Posts80 When I believe the unit has dried sufficiently, I put it back together. Maybe that’s the problem, that it’s not quite dry enough, despite the fact that it appears to be. Perhaps I should keep them separate until I’m ready to utilize them. I do, and I make every effort to obtain my water supply from the deepest, clearest, and quickest running water I can locate. I do find myself fighting the intake hose to keep it from moving on me from time to time. It has floated to the sides of the pool on my behalf on a few of occasions, and it has also drifted to the mossey rocks on occasion. We’re still trying to figure out way to avoid this. Apart from that, the machine appears to be in good working order. 06-13-2010,20:537Registered User
  12. Join Date: 06-13-2010,20:537 Date: December 26, 2004Location: Thompson Station, TNAge: 61Posts410 The check valve located at the bottom of the smaller tube that contains the handle is most likely the source of the problem, since it prevents the unit from drying. After using the filter, I clean and dry it for a couple of days before storing it in a mesh bag for future use. Please experiment with the desecant packs I provided and report back if this resolves the issue. Registering as a User
  13. Joining on April 21, 2012, 13:368 On 04-19-2012, the location was Green Mountains, Vermont, and there were 106 posts. The filter has a capacity of approximately 200 gal (750 L). 04-21-2012,13:529 Coach Lou
  14. Date of Joining Madison, Connecticut is the location of this event on September 3, 2011. Age64Posts4,777Images400 Thank you so much, White Blaze! After reading this discussion, I realized that my gift has already paid its first payout. I purchased the PURE brand model some years ago and have never used it. When I returned to AT this past autumn, I got it out of the attic and started using it. It’s a good tool, but I didn’t realize it needed to be dismantled after each usage. It is currently outside in the sun, allowing the noxious mildew odor to dissipate. Thank you, WB. 04-21-2012,14:0210Registered User
  15. Join Date: 04-21-2012,14:0210 10-10-2007 LocationFreehold, in a squalid neighborhood Jersey Age39Posts211 I’ve used the hiker pro for a number of years (5+), and I nearly never disassemble it after a trip to allow it to dry completely. To now, the most I’ve done is to empty the surplus water from the filter after each use, which I assume is standard procedure for filter users everywhere. In order to ensure there is no mildew development or that the filter has not been polluted in any way, I open it before each trip. So far, no such problems have occurred. I’ve only had to change the filter once in all of these years, and that was because I had to filter some horrible reddish brown water from a stagnant source in an emergency, and the filter became stained with reddish brown dye as a result. Maybe I’ve simply been lucky
  16. One idea I have is that because I don’t open it very often, the filter isn’t affected by mold or mildew spores from the outside world and hence remains clean. Alternatively, it is possible that I have already consumed something that will cause me to die violently in a few years’ time
  17. Only time will tell. 04-21-2012,16:4911Registered User
  18. Join Date: 04-21-2012,16:4911 10-24-2002 Utah is the location of this event. My heart, however, remains in Vermont! Age69Posts901Images1 bycrazyonelost, first published on How frequently is it recommended that the water filter in the Hiker Pro be changed? I’ve been cleaning out my filter at home and observed that the bottom half of the filter is blackish and the top half is still clean looking after rinsing it a several times. Is this normal? With the Katadyn Hiker Pro, there is no cleaning pad to be found. It’s a paper filter, to be precise. When it suddenly becomes considerably more difficult to pump, this is an indication that the filter should be changed. This indicates that the filter is completely filled and that you must drive water through it vigorously. The amount of time it takes for the filter to fill completely depends on the type of water you’re filtering. Water that is muddy or silty will clog it up quite fast. This has been said and done. I get between 600 and 750 hiking miles out of a single filter replacement. It always seems to happen at the same time as I change my boots! Georgia – New Jersey 2001
  19. Georgia – Maine 2003
  20. Georgia – Maine 2005
  21. Georgia – Maine 2007
  22. PCT 2006 A wise man can change his mind, but a fool will never do so. PROVERB
  23. 04-21-2012,17:3712Lurkin’
  24. Join Date: 11-03-2011
  25. SPANISH PROVERB 17197 posts in Group W bench Posts17,197 bycrazyonelost, first published on How frequently is it recommended that the water filter in the Hiker Pro be changed? I’ve been cleaning out my filter at home and observed that the bottom half of the filter is blackish and the top half is still clean looking after rinsing it a several times. Is this normal? So far, I’ve probably put around 10 gallons of water through the system since I got it a few years ago, if that. Yes, every time I return home from a trip, I clean and dry the filter in my car. I’m just interested since I can’t seem to find my way back to my apartment. I, too, have this filter, and I haven’t switched it out yet. When purchased new, these are fairly pricey ($39.99), but I discovered one on clearance at Sports Athority for $9.98, which was a great deal! Aqua Mira would be used as a back-up and/or in addition, depending on the state of the sorce’s energy. So far, the only thing I’ve done is give it a periodic back wash, and it’s still looking good. no mildew
  26. 04-21-2012,18:1113Registered User
  27. Join Date01-09-2008LocationUSAPosts2,866Images71
  28. The original post was made by Karo. This is the water bag to which I was referring. This is precisely the same bag that I use in conjunction with thepur hikerpro. I’ve never had a problem with this system. A fantastic filter (the best), and the water bag can store a 12-pack of B soda and ice in addition to the filter. CrumbSnatcher last revised this page on 04-21-2012 at 18:14.
See also:  How Much Does It Cost To Replace A Hot Water Heater With A Tankless

++Recent Posts++

Posting Permissions

  • You are not permitted to start new posts or reply to existing ones. You are not permitted to submit attachments. You are not permitted to modify your posts.

The Rules of the Forum All times are in UTC minus four. The time is 15:42 right now. Appalachian Trail Enthusiasts are the driving force behind this website.

How to Clean, Sanitize, and Store a Water Filter in the Off Season

The cleaning and sanitization of your backcountry water filter or purifier before putting it away for the winter is critical. There is a straightforward three-step technique for doing this, which includes cleaning the filter to increase its flow rate, sanitizing the filter to kill any bacteria that may be present, and drying the filter before storing it until you’re ready to use it again.

Step 1: Backflush Your Water Filter or Purifier

Several wilderness water filters and purifiers include the capability of being backflushed, which means that the typical flow of water through the filter element may be reversed. This helps to unclog any debris or impurities that have become lodged in the filter, rinse them out, and increase the flow rate of the filter in the process. Many filters and purifiers, such as the Sawyer Squeeze, are supplied with a hose or a syringe, which may be used to accomplish this backflushing procedure, as seen in the video below.

The backflush/cleaning process only has to be performed a few times if you have recently used your water filter or purifier to ensure that it is completely clean.

When backflushing the filter element, avoid applying excessive pressure because this might rip or distort the internal filter element, which may be made entirely of paper depending on the product you are using.

Sawyer says that their filters are quite durable, but others may not be, and I believe it is essential to be firm yet delicate while backflushing the system.

Step 2: Sanitize the Filter Element

In this following step, you must sterilize the filter/purification element and eliminate any bacteria that may have survived the previous step. If they are allowed to continue growing during the winter, they can clog or destroy the filter element, resulting in permanent clogging or damage. The techniques for this operation vary significantly depending on the manufacturer, therefore consult the manufacturer’s website for their advice. However, the two most common methods of sanitizing a water filter/purification element are to flush it with a diluted bleach solution made by mixing one capful of fragrance-free bleach per Liter of water or to mix up a liter of water treated with chlorine dioxide made by mixing Aquamira drops or Katadyn Micropur tablets with the filter/purification element.

Step 3: Drying and Storage

Placing your filter/purifier in a warm, well-ventilated position away from direct sunshine will allow it to dry gently and naturally. Moving the item to a drawer or closet in a warm region of your home after a week is recommended. It will be ready for use when the weather warms up in the spring. Please keep in mind that some manufacturers offer somewhat different processes for this operation, so be sure to consult their websites for their advice. For example, some advocate storing your filter wet once it has been cleaned rather than allowing it to dry completely, such as thePlatypus QuickDrawin seen in the video above.

NOTE FROM THE EDITOR: If you’re considering about purchasing gear that we’ve reviewed or recommended on SectionHiker, you may contribute to our fundraising efforts.

Simply click on any of the vendor links provided above.

Thank you for your assistance, and please know that we appreciate it!

Katadyn Hiker Pro Review

Designed to reach shallow water sources, this hand filter is dependable and easy to use. Katadyn Hiker Pro Transparent is a transparent hiking boot. Photo courtesy of Katadyn”>Photo courtesy of Katadyn Price:$85 on Amazon | $79.77 on the list Compare pricing at three different resellers. Pros: Lightweight, affordable, and dependable, it is capable of reaching shallow water sources. Cons: Requires a lot of energy to filter and gets clogged up with silt. Manufacturer:Katadyn Amber King, Senior Review Editor, published on May 6, 2019 Our Editors do independent research, testing, and rating of the top items available.

We never accept free things from manufacturers.

63 OVERALL SCORERANKED 17 of 25 OUT OF 100

  • 80% of the time, the water quality is 8.0
  • 20% of the time, the durability and maintenance are 7.0
  • 15% of the time, the treatment time is 6.0
  • And 15% of the time, the weight and portability are 5.0. 7.0 percent for ease of setup
  • 15 percent for ease of filtration
  • And 4.0 percent for overall ease of use.

Our Verdict

TheKatadyn Hiker Prois a traditional and dependable hand pump that will last for years. It removes germs as well as protozoans such as Giardia and Cryptosporidium, making it an excellent backpack filter for North America’s wilderness areas. The ultra-long tube and tiny intake allow the pump to reach into tight spaces that conventional hand pumps are unable to reach, allowing it to access a wide range of water sources ranging in size from small to big. While this filter performs admirably in clear water, it struggles when dealing with silty water.

When water sources are not fully clean, it clogs readily since it does not have an automated backflow preventer. The use of this dependable hand pump will keep you hydrated if the water sources are clear and you’re travelling into the woods by yourself or with a group of companions.

Compare to Similar Products

This ProductKatadyn Hiker Pro Sawyer Squeeze Aquamira Water Treatment Drops Katadyn BeFree CrazyCap 17oz
Awards
Price $79.77at AmazonCompare at 3 sellers $29.97at AmazonCompare at 2 sellers $15.00List$14.95at REI $38.51at AmazonCompare at 3 sellers $79List$79.00at Amazon
Overall Score 63 74 72 72 66
Star Rating
Pros Lightweight, inexpensive, reliable, reaches shallow water sources Lightweight, adaptable, easy to use, lifetime guarantee Lightweight, inexpensive, kills all pathogens (including crypto), reliable Easy to use, fast flow rate, collapsible, lightweight Lightweight construction, purifies water with a touch of a button, waterproof, fast charging, long charge retention
Cons Requires energy to filter, clogs with sediment Not great for group use, better if you replace the bags Takes a long time to kill crypto, slight taste to the water, chemical treatment Lacks durability and reliability Can’t filter particulates, doesn’t adapt to many other bottles, small bottle size
Bottom Line This is a reliable hand filter that can reach shallow water sources Simple filtration that is lightweight and reliable for individual use These drops are a reliable and lightweight option to carry all over the world Our favorite lightweight on-the-go filtration system A UV bottle cap purifier that removes viruses from water sources
Rating Categories Katadyn Hiker Pro Sawyer Squeeze Aquamira Treatment. Katadyn BeFree CrazyCap 17oz
Water Quality(20%) 8.0 8.0 5.0 8.0 5.0
DurabilityMaintenance(20%) 7.0 5.0 10.0 1 7.0
Treatment Time(15%) 6.0 9.0 2.0 9.0 5.0
WeightPackability(15%) 5.0 8.0 9.0 9.0 4.0
Ease Of Set Up(15%) 7.0 7.0 8.0 9.0 9.0
Ease Of Filtration(15%) 4.0 8.0 9.0 9.0 10.0
Specs Katadyn Hiker Pro Sawyer Squeeze Aquamira Treatment. Katadyn BeFree CrazyCap 17oz
Type of filter/purifier Hand pump Squeeze, in-line, on-the-go Chemical treatment Squeezeon-the-go UV treatment
Measured weight (entire kit, oz) 380 g | 13.4 oz 162 g | 5.7 oz 85 g | 3.0 oz 59.5 g | 2.1 oz 357 g | 12.6 oz
Number of liters (L)/gallons (gal) per lifetime 1,100 L/291 gal 378,541 L/100,000 gal 114 L/30 gal per package 1000 L/264 gal 236,588 L/62,500 gal
Filter media or active ingredient Glass fiber/ carbon core Hollow Fiber Chlorine Dioxide Hollow Fiber UV light
Effective against bacteria? Yes Yes Yes Yes Yes
Effective against protozoa?(Cryptosporidium, Giardia) Yes Yes Yes Yes Yes
Effective against viruses? No No Yes No Yes
Effective against chemicals? Yes No No No No
Effective against heavy metals? No No No No No
Removes Particulates(sediment, microplastics)? Yes Yes No Yes No
Filter pore size 0.2 microns 0.1 micron N/A 0.1 micron N/A
Advertised flow rate 1L/min 1.7L/min N/A 2.11 L per min N/A
Dimensions 6.5 x 3 x 2.4 in 11 x 6 N/A 9.05 in x 2.73 in N/A
Storage capacity (L) 2 L 0.6 L 0.5 L

KATADYN Hiker Pro is a traditional and dependable hand pump that has been around for decades. For North America, it is an excellent backpack filter since it removes germs and protozoans such as Giardia and Cryptosporidium. This hand pump’s ultra-long tube and compact input allow it to reach into tight spaces that other hand pumps are unable to reach, allowing it to access a wide range of water sources from small to big. Even though this filter performs admirably in clean water, it struggles in muddy water.

The use of this dependable hand pump will keep you hydrated if the water sources are clear and you’re traveling into the woods by yourself or with a group of pals.

Our Analysis and Test Results

TheKatadyn Hiker Prois a low-cost, high-quality handpump with excellent reliability. It is completely content to provide clean and fresh water to small groups of hikers and single travelers. Despite the fact that it takes some effort to acquire a liter of water, it is one of our favorite hand pumps on the market today.

Performance Comparison

It’s an economical and dependable handpump, the Katadyn Hiker Pro. For small groups and lone hikers, it is completely content to provide clean and fresh water. This hand pump is one of our favorites on the market, despite the fact that it takes some effort to fill a liter container.

Water Quality

There are 0.2-micron pore sizes in this filter’s anticlog pleated cartridge, which is made of glass fiber and activated carbon. It can filter out typical bacteria and protozoans (Giardia and Cryptosporidium), as well as other contaminants. The activated carbon performs an excellent job of removing any unpleasant odors or stenches from the water, leaving you with fresh, clean water to drink while hiking. Our favorite feature is the transparent coating, which lets you can see the water that you’re filtering out as rapidly as possible.

Amber King contributed to this image.

Amber King contributed to this image.

Durability and Maintenance

There are 0.2-micron pore sizes in this filter’s anticlog pleated cartridge, which is made of glass fiber and activated carbon. It can filter out typical bacteria and protozoans (Giardia and Cryptosporidium), as well as other microbes. In addition to removing any unpleasant odors or tastes from the water, activated carbon also leaves you with fresh and clean water to drink when hiking or backpacking. The transparent coating, which lets you to see the water that is being filtered out rapidly, is also a plus in our opinion.

Amber King is shown here. When properly maintained, the filter may remove bacteria, particles, and protozoa from water while leaving viruses alone. Amber King is shown here.

Treatment Time

The course of treatment is rather short. Our timed testing showed that it took us an average of 53 seconds to pump a liter of water. The flow is pleasant and swift, allowing for speedy filtering. While we believe that the moment is appropriate, we do not believe that it is as early as some hand pumps out there believe. One of the concerns we experienced with the Hiker Pro was that the handle was difficult to grasp, which we found to be a disappointment. A few pumping sessions later, we noted that it was becoming increasingly difficult to push the water through the filter.

In this case, we pump some water while on the road, which doesn’t take long at all.

Amber King contributed to this image.

specifically to fill this one-liter personal-use jug, which is barely shy of the mark.

Weight and Packability

A relatively short period of time is required for the treatment to be successful. On average, it took us 53 seconds to pump a liter during our timed trials. Fast and smooth flow ensures that the filtration process is expedited. However, while we believe that the time is appropriate, we do not believe that it is as early as some hand pumps out there believe it to be The handle on the Hiker Pro is also difficult to grasp, which was one of the challenges we encountered with it when it first arrived.

We were satisfied with the entire treatment period despite the fact that these complications occurred.

to fill this personal use jug that holds little less than one liter in volume, in particular Amber King is shown here.

“> to fill this personal use jug that holds little less than one liter in volume, in particular Amber King is shown here.

Ease of Setup

After the first assembly, the rest of the process is rather straightforward. Simply click everything into place and you’re ready to start. When you’re ready to take the filter out on the trail, simply dump the bag, open it, and start pumping immediately. Although it comes with a bottle adaptor, if the opening of the bottle is too tiny (or if the adaptor is lost), you may just submerge the tube in the water for simple filtering. Amber King contributed to this image. There is a bottle adaptor included, but if the mouth is too tiny (or if the adaptor is lost), you may just submerge the tube in water for simple filtering.

The hose that comes with the arrangement is equipped with a well constructed tiny float that prevents the tube from striking the bottom of the puddle and sucking up mud and other debris.

On a journey to Death Valley, we discovered that it was simple to obtain water from little puddles with little effort.

Water may be obtained from any source.

Make sure to pump through a large amount of water before using your first filter that you want to consume. When we first started filtration, the water was stained black due to the presence of activated carbon in the system. After roughly 2L of pumping, the water was crystal pure once more.

Ease of Filtration

Setup is rather straightforward after the initial construction. After putting everything in its proper position, you may begin your journey. When you’re ready to take the filter out on the trail, simply dump the bag, open it, and start pumping it. Despite the fact that it has a bottle adaptor, you may just insert the tube into the water to filter it if the mouth becomes too tiny (or if you lose the adaptor). Amber King is shown here. There is a bottle adaptor included, but if the mouth is too tiny (or if the adaptor is lost), you may just submerge the tube in water for simple filtering.

  • The hose that comes with the arrangement is equipped with a well built tiny float that prevents the tube from striking the bottom of the puddle and sucking up mud and debris.
  • Our group discovered that getting water from little puddles did not require much effort when traveling through Death Valley.
  • Anywhere will do to get you some water!
  • Because of the activated carbon contained therein, our first filter produced water that was colored black.

Value

Our is one of the best-value pumps we’ve seen so far in this evaluation. It delivers excellent performance, is quite flexible, and does not come at an exorbitant price. That is precisely why we selected this product as one of our Best Buy award winners. If a handpump is what you’re looking for, the Hiker Prow won’t let you down. On the approach to Mount Ritter in the Easter Sierras, I’m filtering water with my Hiker Pro filtering system. Photograph by Luke Lydiard Water being filtered via the Hiker Pro on the approach to Mount Ritter in the Easter Sierras.

Conclusion

The Katadyn Hiker Pro is a portable handpump that is both lightweight and cheap. During the course of its filter’s lifespan, it can treat a moderate volume of water. While it may seem a little cumbersome at first, you’ll soon discover that you can readily reach any water source, with the ability to filter directly into any storage tank you might be carrying with you on the trail. The Katadyn Hiker Pro is a well-made and dependable backpack. Jessica Haist contributed to this image. “>The Katadyn Hiker Pro is a well-made and dependable backpack.

Katadyn Gravity BeFree Water Filtration System – 3 Liters

  • The 0.1 micron microfilter has been evaluated for its ability to guard against hazardous organisms
  • It has been shown to eliminate 99.99 percent of protozoa and 99.9999 percent of bacteria according to EPA guidelines. If you compare it to the basic BeFree 3L filter, this filter comes with a handy output hose, which allows you to rapidly fill water bottles and hydration systems. For hands-free filling of hydration bladders, the output hose incorporates quick-connect hydration-pack adapters on both ends. a quick-release cap with an auto shutdown for convenient filling without the use of any hoses, as well as a quick output hose attachment
  • With the integrated bail handle and carry loop/hang strap with clips, you can quickly and easily hang the robust and foldable 3-liter HydraPak reservoir. It can filter up to 2 liters of water per minute. Filling from a lake, stream, or faucet is simple with the 42mm wide-mouth aperture. To remove dirt from the EZ-Clean membrane, simply shake or swirl it around. Individual findings will vary depending on the quality of the water used in the testing
  • In addition, a tote bag and a separate bag for the outlet hose are supplied to keep the hose clean and prevent cross-contamination. Made without the use of BPA-containing materials

In tests, the 0.1 micron microfilter was shown to be effective in protecting against hazardous organisms; it eliminates 99.99 percent of protozoa and 99.9999 percent of bacteria in accordance with EPA guidelines; If you compare it to the basic BeFree 3L filter, this filter comes with a handy output line that allows you to easily fill water bottles and hydration systems. For hands-free filling of hydration bladders, the output hose incorporates quick-connect hydration-pack adapters on both sides.

With the integrated bail handle and carry loop/hang strap with clips, you can hang the robust and foldable 3-liter HydraPak reservoir in seconds.

Filling from a lake, stream, or faucet is simple thanks to the 42mm wide-mouth hole.

Individual findings will vary depending on the quality of the water being tested.

Made without the use of BPA-containing components.

Leave a Reply

Your email address will not be published.