How Much Is A New Water Pump

Water Pump Replacement Cost 2020

The average water pump replacement cost is$550, with prices ranging from $461 to $638 in the US in 2020. However, the sort of car you drive and the auto repair business you take it to are also important considerations. Labor expenses range between $256 and $324, while component prices range between $205 and $314, depending on the manufacturer. Fees and taxes are not included in the estimate. $461 on the low end; $550 on the average. $638 is a lot of money.

Repairs commonly related to water pump replacement:

Timing Belt Replacement Prices range from $554 to $689. Replacement of the timing chain and gear set will cost between $805 and $963.

What is a water pump?

The water pump is responsible for distributing coolant throughout the engine’s cooling system, which helps to keep the engine from overheating.

How does it work?

With the help of the water pump, you can keep your engine from overheating by distributing coolant throughout its cooling system.

What are indications associated with a bad water pump?

Loud sounds and leaks are two of the most typical indications that a water pump is malfunctioning. It is possible that leaky water pumps could cause damage to the drive belts and timing belts, which would result in the overheating of the vehicle’s engine. Other problems with the vehicle’s cooling system, such as a broken or failing thermostat, head gasket, or radiator, might be the cause of a failed or malfunctioning water pump.

Am I able to drive with water pump problems?

It is possible for the engine to overheat when the water pump is not providing adequate coolant circulation, resulting in leaks, probable head gasket failure, and, ultimately, a damaged engine. Stopping at the side of the road and turning off your car as quickly as you safely can can prevent your vehicle from overheating. In order to get the car to an auto repair center, you’ll need to tow it.

How frequently are water pumps required to be replaced?

It is possible for the engine to overheat when the water pump is not providing adequate coolant circulation, resulting in leaks, probable head gasket failure, and, eventually, a damaged engine. Stopping on the side of the road and turning off your car as quickly as you safely can can prevent your vehicle from overheating. Having the car towed will be necessary in order for it to be repaired at a garage.

Estimated water pump replacement cost

A car Water Pump Replacement will typically cost between $461 and $638 on average, however the price can vary from vehicle to vehicle. Symptoms of a malfunctioning water pump

  • Intense cooling system temperature rises
  • Steam pours from the radiator
  • Strange engine noises
  • Leaking radiator fluid
  • Varying temperature readings
  • Overheating engine

Common vehicle water pump replacement costs

  • Ford F-150 –$226 – $288
  • Toyota Camry –$351 – $492
  • Chevrolet Silverado 1500 –$454 – $610
  • Toyota Corolla –$304 – $420
  • Ford Explorer –$229 – $313
  • Ford Escape –$181 – $212
  • Ford Escape –$181 –

OBD codes associated with water pump replacement

A01: Range/Performance P0A01:

Vehicle Water Pump Replacement Service in Glendale, Arizona

We offerwater pump replacement If you suspect that your water pump is malfunctioning or if you would like to have your water pump tested, please contact our staff. Regardless of the make or model of car you possess, the specialists at Sun West Transmissions are well qualified and can execute water pump replacement on it. Call (623) 842-0806 today to arrange an appointment for your vehicle’s check-up or repair. Please keep in mind that these are not actual costs. It is possible that the cost of replacing your vehicle’s water pump will be different from the costs shown in this page.

The Complete Car Water Pump Replacement Cost Guide

When your car’s engine is running, it has a water pump, which is made of aluminum and iron and plays an important role in keeping the vehicle cool. Water and coolant are circulated through your car’s circulation system by an impeller, which is the object that looks like a fan. This is essential in order to protect your engine from overheating. The water pump is located close to the engine, and in order for it to function, it must rotate, therefore circulating the water. Your water pump’s driving belts or timing belts are responsible for ensuring that this occurs.

One way to tell if your water pump is failing is to search for coolant below your car’s engine.

When a water pump’s seals begin to fail, coolant will begin to leak from the pump, which is easily visible.

As part of your vehicle’s routine maintenance, you should do this procedure every 50,000 miles. If you require a new water pump, you will be able to identify the problem. Among these is the following list of possible signs that your water pump is malfunctioning:

  • There is a leak in your coolant (which is a red, green, or yellow liquid)
  • Your car is overheating
  • Your car will not start

Thanks to modern technology, it’s feasible to get your water pump changed for a cheap price if you seek in the appropriate areas. Another useful resource is the video below, which offers a comprehensive summary of what to look for in a leaky water pump. A reputable technician will charge you far less for a water pump replacement than a dealership will, so shop around and pick someone who is honest and isn’t out to take advantage of you by overcharging you. Depending on the make and model of your car, you should expect to pay anywhere from $150 to $800 for a replacement water pump, not counting labor.

  • Don’t spend more than $800 in total!
  • First and foremost, they will drain the coolant from your vehicle.
  • They will repair the water pump and coolant, and they may even need to replace the timing belt and drive chain, if that is what is required by the situation.
  • Keeping an eye out for coolant leaks is critical since it allows you to pick which mechanic will do the necessary repairs rather than being stranded in your car while it is not moving.
  • It is recommended that you do not change the water pump yourself unless you have prior knowledge with mechanical work.
  • If you wish to purchase the pump independently, you may be able to get one for as little as $40 on the internet or via contacts.
  • Good luck with your automobile, and remember to keep an eye out for any coolant leaks!

Water Pump Costs Submitted By Our Users

Compare your quotation to that of other people from all across the country to ensure that you are receiving the greatest value possible. For Water Pump, the average cost is $522.

Loading Chart.

The most recent update was made on May 20, 2021. In-cylinder internal combustion engines are propelled by a series of small explosions. These explosions generate a great deal of heat, which, if left unattended, can cause damage to the engine. Are you looking for a reliable online repair manual? The top five choices may be found by clicking here.

A water pump, which circulates coolant (also known as antifreeze) throughout the engine’s components, ensures that this does not happen. Below, we’ll go over five typical malfunctioning water pump symptoms that might show themselves along with the approximate cost to replace a water pump if needed.

How a Water Pump Works

When the vehicle’s engine is operating, coolant from the radiator is drawn into the center of the water pump, where it is stored. The crankshaft powers the impeller of the water pump, which circulates coolant throughout the engine in a manner similar to how a heart pumps blood. The fluid is driven into the cylinder head and engine block by the pump blades, which are also known as vanes. Once in the radiator, it returns to the water pump, completing the cycle hundreds of times per minute, and the process is repeated.

Symptoms of a Bad Water Pump

The rapid overheating of an engine can result in engine failure, which is a highly expensive consequence. Being familiar with how water pumps function in order to keep your car cool is vital, but it’s even more crucial to be familiar with the indicators of a failed or broken water pump in order to solve the issue as soon as possible. The following are the five most prevalent signs and symptoms.

1 – Elevated Coolant Temperature

It goes without saying that an overheated engine is the most evident sign of a bad water pump. In most cases, an engine temperature warning light (or an emblem with wavy lines in it) will illuminate on the dashboard, and the engine temperature will be higher than normal. A properly functioning water pump cools the engine by circulating coolant; therefore, a malfunctioning water pump will allow engine heat to accumulate to dangerous levels. Note that the temperature gauge in certain vehicles will not move off center until engine temperatures have reached unsafe levels, so proceed with caution if the needle begins to rise over its usual operating temperature setting.

2 – Radiator Steam

Overheating can also be indicated by the presence of steam coming from the front of the vehicle when it is driving or stopped. The evaporation of coolant occurs when the water pump is not functioning properly, since coolant cannot flow through the radiator to cool it down effectively. Remove your car to the side of the road if you notice steam rising from the front of it. Driving with an overheated engine for an extended period of time might result in permanent damage. It is possible that the reason of an overheated engine is anything other than the usual suspects such as a damaged radiator or a malfunctioning thermostat, but the consequence is the same.

3 – Unusual Sounds

A whining, buzzing, or squealing noise coming from the engine might be caused by a loose auxiliary belt, which could be caused by a loose pulley or worn out bearings. If the faulty bearings are located in the water pump, the pump will need to be completely replaced. Overtight auxiliary belts are a major cause of early water pump failure, and they are one of the most prevalent reasons. In the event that you decide to replace the water pump on your own, it is highly suggested that you obtain an abelt tension gauge to guarantee that the tension is accurately adjusted to specification.

Whining that becomes more audible as the vehicle accelerates should be investigated by a mechanic as soon as possible.

4 – Fluid Leak

After your automobile has been parked for a few hours, a bright green or orange fluid may have accumulated beneath the front of the vehicle. This fluid may be coolant. Gaskets and seals in the water pump might wear out and fracture or break, causing this to occur. Although no pool of fluid is visible, it’s still worth checking the water pump itself (especially if you’re experiencing any other symptoms) to see whether it appears to have more debris on it than the other components in the engine room.

A slow trickle of coolant can produce rust or corrosion (as shown by “pitting” in the metal) on the outside of the water pump, or it might induce solidification on the inside of the water pump.

When the pump is spinning (i.e., when the automobile is running), certain leaks will only occur; however, some leaks will occur even when the car is not moving.

It is possible that a leak from the weep hole of the water pump is caused by a damaged seal, because the weep hole prevents the contamination of oil in the bearings with coolant and vice versa.

5 – Inconsistent Temperature Gauge Readings

A properly functioning cooling system will ensure that the temperature gauge remains within standard operating limits at all times. A defective water pump, on the other hand, might cause the temperature gauge needle to bounce between normal and heated temperatures, and vice versa. This can also be caused by a faulty radiator, but both of these issues should be addressed before the car is allowed to be driven again. Another probable reason of temperature changes in coolant is the presence of an air bubble.

Water Pump Replacement Cost

The cost of replacing the water pump varies widely based on the size, brand, and age of the vehicle, but you could anticipate to pay anywhere from $310 to $730 in total. At a dealership or with specific types of automobiles, you should expect to pay extra. It will cost between $70 to $400 in parts alone (water pump and related parts). Expect to pay between $240 and $330 for labor (based on a median hourly cost of $80-$110/hr.). Water pump replacement takes an average of three hours to complete.

See also:  How Hot Does Hot Water Heater Get

The make and type of a car can have a major impact on the entire cost of the vehicle.

Although replacing a water pump might be costly, replacing an engine is far more expensive.

If you’re not sure when your water pump was last replaced, replacing it as soon as possible is a low-cost form of engine insurance. While they’re in there, the majority of folks want to take on the water pump with the timing belt.

Replacement Process

The cost of replacing the water pump varies widely based on the size, brand, and age of the vehicle, but you may anticipate to pay anywhere from $310 to $730 in total. At a dealership or with specific sorts of automobiles, you might expect to pay extra. It will cost between $70 to $400 in parts alone (water pump and other components). Expect to pay between $240 and $330 for labor (assuming an hourly rate of $80-$110). It takes an average of 3 hours to replace a water pump. Purchasing the pump and delivering it to the technician for installation may result in lower costs; however, exercise caution and ensure that you purchase the parts from a trusted supplier.

Depending on your area, additional fees and taxes may be added to these amounts.

It is not recommended to drive the car until the necessary repairs have been completed.

While they’re in there, the majority of folks enjoy tackling the water pump with the timing belt.

Warning!

Depending on the size, model, and age of the vehicle, the cost of replacing the water pump might range from $310 to $730 in total. At a dealership or with specific types of automobiles, you might expect to pay extra. The parts alone (water pump and other accessories) will cost between $70 to $400. Expect to spend between $240 and $330 for labor (based on an average $80-$110/hour cost). The average time to replace a water pump is three hours. Purchasing the pump and delivering it to the technician for installation may result in lower costs; however, exercise caution and make certain that the parts are purchased from a trustworthy source.

Fees and taxes may be added to these amounts, depending on where you live.

The car should not be driven until the necessary repairs have been completed.

While they’re in there, most folks prefer to take on the water pump with the timing belt.

Learn how much it costs to Replace a Well Pump.

It was last updated on February 8, 2022. Jeff Botelho, a Licensed Journeyman Plumber, provided his review. HomeAdvisor has contributed to this article.

Cost to Replace Well Pump

According to more than 600 homeowners who participated in a poll, the average cost to replace a well pump is $1,701, with costs ranging between $926 and $2,502. Deep-well projects cost around $2,000, whilst shallow-well ones cost approximately $1,000. The majority of well pump systems are priced between $100 and $1,200. The expenses of replacing a well pump vary depending on the type of pump, its depth, its location and the size of your well. For example, repairing a shallow well jet pump is often less expensive than replacing a residential well pump that is submerged in the ground.

A deep well jet pump is most likely to be found anywhere in the middle of the range. Having a failing pump repaired or replaced is critical, especially if your well serves as your principal supply of drinking water.

Well Pump Replacement Cost Calculator

Let’s run some numbers to see what the costs are. What part of the world are you in? What part of the world are you in?

National Average $1,701
Typical Range $926 – $2,502
Low End – High End $200 – $4,550

The cost information in this report is based on real project costs submitted by 1,103 HomeAdvisor users.

Cost to Replace vs. Repair Well Pump

You may find it difficult to evaluate whether well pump repair or well pump replacement is the most appropriate course of action when you are suffering well pump problems. Among the questions that might assist you in making your selection are the following:

  • How long can I expect my well pump to last if I finish this repair
  • Does the cost of a repair equal 50 percent or more of the cost of replacement

Overall, if you anticipate that a well performed repair would extend the life of your well pump and well for several more years and if the cost of that repair is less than half the cost of replacement, repair is the better option. If, however, your well pump is towards the end of its estimated lifespan and a repair won’t buy you long, or the repair is more than half the cost of a replacement, it’s likely better to replace the complete well pump.

Average Well Pump Prices

The typical cost of a new well pump ranges from $200 and $800, depending on the size and kind of pump purchased. Submersible pumps cost between $200 and $1,200 before installation, and jet pumps cost between $100 and $800 before installation. Solar energy systems will cost you at least $2,000. Hand pumps are available for as little as $150.

Type of Pump Cost
Submersible (3/4 – 5 horse power) $200 – $1,200
Deep Jet $175 – $800
Shallow Jet $100 – $500
Hand $150+
Solar $2,000+

Jet Pump Prices

Shallow well pumps (25 feet or less in depth) using smaller motors and less expensive materials such as thermoplastic may be expected to cost approximately $270. Deep-well motors (up to 150 feet in depth) made of higher-quality materials such as cast iron will cost about between $675 and $745 on average. Jet pumps are available in a variety of materials, including cast iron, stainless steel, carbon ceramic, and thermoplastic. The majority of jet pump motors have a horsepower rating between one-half and two horsepower.

In some cases, jet pumps fail to function properly owing to a lack of prime, but submersible pumps always function well due to self-priming.

In many instances, motor repairs are as expensive as the installation of a new pump.

Submersible Well Pump Cost

The average cost of a submersible pump with a lesser horsepower is $475, or between $200 and $500. More powerful devices are available for between $700 and $1,200. Additionally, many submersible pumps require the construction of extra plumbing, which will raise the entire cost of the project by a significant amount. Depending on the nature of the job, adding more pipe might cost anywhere from $250 to $2,500 more. There are three-quarter to five-horsepower submersible pumps available in both cast iron and stainless steel construction.

Submersible pumps are believed to be more dependable than jet pumps, despite their higher cost. They are also thought to be less loud. The cost of installing submersible pumps will vary depending on the size of the well, the type of material used, and the size of the motor.

Solar Powered Well Pump Cost

Solar pumps are available in two different housing materials: plastic and stainless steel. Stainless steel versions will cost a premium price, but will last for a longer period of time. Pump setups for shallow and deep wells will cost roughly $2,000 and will pump water from both shallow and deep wells. A greater gallon-per-minute rate may be achieved by high-end versions, which can pump from a wider range of well depths. The price of these pumps will range between $3,000 and $4,000.

Hand Pumps

Hand well pumps are available in a variety of materials including plastic, cast iron, and stainless steel. Pumps made of plastic that are shallow in design are reasonably priced, starting at roughly $150. It is possible that larger, stainless deep well pumps will be more expensive depending on the design and size of the well. Hand pumps can be physically taxing, but they will continue to run regardless of the weather or availability of utilities.

Compare Well Pump Replacement Prices

Image courtesy of a3701027 / Adobe Stock Well pump replacement prices can range from $200 to upwards of $5,000, with the majority of homeowners reporting a cost between $923 and $2,486 to have their pumps changed. The cost of replacement will vary depending on a number of factors. Here’s a look at the factors that might influence the cost of your new pump:

  • In order to determine your replacement expenses, the size and depth of your well are important factors to consider. Pump installation in shallow wells is less labor-intensive than pump installation in broader, deeper wells. Shallow pumps, which are more cheap, are best suited for wells with a depth of less than 25 feet, according to the manufacturer. Deep pumps are required for wells with a depth of up to 150 feet in the ground. The cost of purchasing and installing a deep pump will be higher.
  • Pump Type: The type of pump you install has a significant impact on the entire cost. As a result of their design, jet pumps are less difficult to remove and replace than submersible alternatives.
  • Replacement method: Hiring a professional will be more expensive than attempting to replace the item yourself. It’s advisable to leave the job to a professional unless you have prior expertise changing and installing well pumps. Pump repairs that are performed on a whim might be highly pricey. Problems with the pressure tank: The majority of wells transport water to a pressurized storage tank. It is possible that a faulty tank is the source of your pump or well problems. The cost of replacing your storage tank might range from $800 to $3,800.

Changing Pumps

Instead of replacing their jet pumps, homeowners with faulty jet pumps may choose to upgrade to a more contemporary submersible pump instead of replacing their jet pumps. Making the switch from an outdated jet pump to a submersible unit will benefit your house in a variety of ways. The following are some of the advantages of upgrading to a submersible pump:

  • Maintenance: Because submersible pumps are self-priming, they require less maintenance and wear and strain on the device.
  • Instant pressure: Because they are not operating against gravity, submersible pumps generate pressure 30 percent faster than jet pumps.
  • High energy efficiency: Submersible pumps are more energy efficient and quieter than jet competitors because of their architecture. If your well is close to your home, noise might be a significant consideration.
  • Submersible pumps are totally sealed, which reduces the need for repairs and lowers the cost of electricity. Despite the fact that submersible pumps are more expensive up front, they often save money on water pump costs in the long term by reducing the need for repair and energy use.

Off the Grid Installations

It is also possible to install solar panels or hand-crafted patterns. Some of the advantages of using off-grid pumps are discussed in detail below.

  • Efficiencies in energy use. Due to the fact that hand and solar pumps do not rely on utilities to work, they are incredibly energy efficient.
  • Efficiencies in energy use and consumption. Due to the fact that hand and solar pumps do not rely on utilities to operate, they are incredibly energy efficient.

Even while hand and solar pumps are excellent for outbuildings and other non-essential water sources, they might make it difficult to use water in the home itself. Before building an off-grid pump, it is important to determine how much water your household uses.

Hire A Well Pump Replacement Professional

Even while hand and solar pumps are excellent for outbuildings and other non-essential water sources, they might make it difficult to use water in the home. Before building an off-grid pump, make careful to calculate your household’s water demand.

  • Even while hand and solar pumps are ideal for outbuildings and other non-essential water sources, they might make it difficult to use water in the home. Before building an off-grid pump, it is important to determine how much water your residence uses.
  • Jet pumps: Jet pumps function in the same way as a straw. These pumps use a combination of pressure and suction to pull water from a well or borehole. Many jet pumps are designed to work in both deep and shallow well settings
  • However, others are only designed for deep wells.
See also:  How To Keep Water Heater From Freezing

In the same way a straw works, jet pumps do. In order to pull water from a well, these pumps use a combination of pressure and suction. Many jet pumps are designed to work in both deep and shallow well settings; however, some are only designed to work in deep well situations.

  • Hand pumps: Hand pumps pull water from a well by turning a lever that is operated by hand. This sort of pump is beneficial in locations where there is no electricity, but it may be exhausting to operate.
  • The solar well pump takes water from a well by using solar energy to power a motor that sucks the water from the well. The effectiveness of solar pumps might be reduced when the weather is cloudy or gloomy.

The majority of contemporary well pumps are powered by electricity. The pumping action of well pumps does not occur continuously each time a water supply is turned on and off. Instead, they transport water to a holding tank where it may be stored.

When the water pressure in the tank falls below a specific level, the pump kicks in and adds additional water to make up for lost volume. Submersible pumps and jet pumps are both capable of operating in both deep and shallow wells.

Deep vs. Shallow Wells

When it comes to upgrading, repairing, or installing a pump, the depth of your well is critical to consider. An examination of the variations between various well depths is presented here.

Well Type Depth Special Considerations
Percussion or Rotary Drilled
  • The use of casings and screens is frequently necessary to ensure stability and keep water free of sediments.
  • When it comes to maintaining stability and keeping water free of particles, casing and screens are frequently necessary.
  • They are typically brick or stone lined on the outside and are prone to drought and pollution.
Find a Well Pump Repair Pro Near You

With brick or stone lining on the outside, these structures are particularly prone to drought and pollution.

Signs You Need a New Well Pump

Discolored water, loud noises, irregular pressure, air in your faucets, and unexpected rises in water bills are all symptoms that your well pump needs to be replaced. A large number of pump difficulties are caused by electrical or mechanical failures, respectively. You should consult with a professional if you are suffering any of the problems listed above. A specialist in the field of pumps will be able to identify the problem and suggest an appropriate solution.

  • When should you anticipate a repair? Simple pump repairs may generally be completed in under an hour for minor hardware damage, minor motor concerns, and minor well problems. The average cost of a water pump repair is between $300 and $1,300 for most households. You’ll know when to anticipate a replacement when. Major mechanical, engine, or well issues might necessitate the replacement of the entire pump.

Why Hire a Pro

It is critical to hire a professional to maintain your well pump for a variety of reasons. A expert will be able to identify the issue and recommend the most effective remedy. Using the services of a professional is also a smart option if you aren’t sure how deep your well is or what type of pump you currently have in place. Pump difficulties include issues with the motor’s ignition and shut-off, as well as a lack of water pressure. Electrical faults can cause these issues in some cases, and if the voltage is too low, the power company may be called in to assist with the situation.

Occasionally, the pump and pipe will need to be removed from the well for repair or replacement.

Professionals often utilize a derrick truck or a puller machine to remove the pump from the ground.

FAQs

It is normal for your well pump to fail when you experience dirty water, loud noises, irregular pressure, air in your faucets, and unexpected spikes in your water bills.

How long does a well pump last?

A well pump is expected to last around 15 years if it is properly maintained. If a pump is not well maintained or suffers damage, it will most likely fail before reaching the 15-year mark.

Is a well pump covered by insurance?

With regular maintenance, a well pump may endure for around 15 years. Because of improper maintenance or damage, a pump’s life expectancy is fewer than 15 years in most cases.

How long does it take to replace a well pump?

While the length of time it takes to repair your well pump may vary depending on the kind and depth of your pump, you can generally expect your professional to spend between a half and a full day on the job.

How Much Does Replacing a Water Pump Cost?

Water Pump: $50-$100+ Labor: $200-$450 Professional Replacement: $300-$750
The water pump pushes coolant throughout the engine to prevent it from overheating. Water pumps generally need to be replaced around 100,000 miles or so.Typical costs:
  • In most cases, hiring a mechanic to repair a water pump would cost between $300 and $750, depending on the make and model of the vehicle and the number of parts that must be removed. A water pump, which must be purchased individually, can cost anywhere from $50 to $100 or more, depending on the make and model of the automobile. For example, the A1 Cardone Select New Water Pump, which fits the 2003 Honda Accord, can be purchased for $49 from Northern Auto Parts, which is situated in Iowa. The Beck Arnley Water Pump, which suits the 1997-2000 BMW 528i, can be purchased for $79 from the online shop AutoPartsWarehouse.com. Work on the water pump will cost between $200 and $450 in total, depending on how difficult it is to reach the water pump, whether any further parts need to be removed, and whether the automobile is equipped with a timing belt or chain. It will take around three and a half to four hours to finish the work. Typically, dealerships charge more, but their technicians are intimately knowledgeable with the brand of the automobiles they work on, and they utilize original equipment manufacturer components. The cost of service at an independent repair shop may be lower because they employ aftermarket components, which are constructed to factory requirements but are not manufactured by the carmaker.
Related articles:Replacing a Timing Belt,Replacing a Timing Chain,Replacing a Transmission,Car Rental
What should be included:
  • In order to complete the repair, the coolant must be drained from the vehicle. The drive belt or timing belt, as well as any other parts that hinder access, as well as the gasket that is connected between the water pump gasket that is put between the engine and water pump, must also be removed. Water pumps and coolant should be replaced, and in certain cases, belts should be replaced if they are worn or broken, according to the manufacturer’s recommendations. It is preferable to obtain an estimate before proceeding with any work if at all feasible. Alternatively, if the water pump has developed a significant leak or has stopped working altogether, this may not be viable
  • As a result of the additional labor required, adding coolant, replacing fan belts, and replacing seals can all increase the overall cost of a repair, depending on the vehicle. A mechanic may recommend that you replace the water pump at the same time as you replace the timing belt or timing chain in order to save money. This is due to the fact that, on certain cars, the timing belt or chain must be removed in order to access the water pump, and completing the repair at this time removes the need to conduct it later.
  • Some repair firms provide frequent clients with a discount on repairs, which is often around 10%. Water pump replacement is a tough procedure that should only be performed by expert technicians or individuals with significant auto-repair knowledge. Water pump replacement instructions are provided by DMV.org, an automobile message board that is not linked with any state government.
  • Among the resources available from the National Institute for Automobile Repair Excellence, a non-profit trade organization for technicians and other automotive service professionals, is a searchable database of accredited businesses. Water pumps are available from a number of internet vendors, including RockAuto.com and AutoPartsWarehouse.com. Alternatively, water pumps are available from large merchants such as Napa Auto Parts and O’Reilly Auto Parts.
CostHelper News
What People Are Paying – Recent Comments
Page 2 of 2-Previous12
Posted by:Charlie Lavalley in DERRY, NH. Posted:August 12th, 2020 04:08AM
Mechanic:Motor-craft Brand:Mariner 3.0 L V-6
Hours of Labor:6 hours
Needs specialist tools to remove pulley from cam shaft to remove water pump bolts – Contacted several Automotive repair garages and no one wanted to do the job- Excuse was they didn’t have the tools to do it.labor as due to all the items that had to be removed to get to the water pump.
Posted by:a user in East Hanover, NJ. Posted:June 22nd, 2018 03:06PM
Hours of Labor:2
Was charged 100.00 for the pump which I knew was high and 2 hours labor @ 100.00 an hour plus a new thermostat was thrown in. Thought very fair. included the antifreeze too. Done at Lukoil gas station off Eaglerock Ave. Mechanic was quite knowledgeable.
Posted by:Schrock in Sarasota, FL. Posted:February 28th, 2018 05:02PM
Hours of Labor:2
The mechanic said he had to charge me 100.00 extra for a new fan clutch Wich wasn’t true at all I checked the price the water pump kit come s with a new fan clutch
Posted by:a user in Ashland, KY. Posted:September 22nd, 2017 12:09PM
Hours of Labor:4
Too daft and old to do it myself. Glad to provide my local garage work. Dealerships will skin you alive. Support the local folks.
Posted by:a user in Mazomanie, WI. Posted:February 8th, 2017 06:02PM
Hours of Labor:6
Did it myself. Likely took much longer than a shop, but paid myself (essentially) $75/hr. Learn this type of easy stuff and you will save yourself tens of thousands of dollars over your life time (I have – brakes, water pumps, external easy stuff – it really isn’t rocket science). It is also satisfying/rewarding when you can fix it yourself.
Posted by:DiyMax in Temecula, CA. Posted:December 19th, 2016 08:12PM
Hours of Labor:I worked on it.
I was quoted $780 so I decided to get it done myself. It was quite easy to do just be sure to purchase anew ac belt/serpentine belt/ thermostat/RTV (NOTE APPLY LIGHT COAT) and spec out all torque specs. All said it took me 3 hours.
Posted by:Hobo Charlie in pontiac, MI. Posted:August 14th, 2016 07:08PM
Hours of Labor:3
It was a GMC jimmy it only took me 2 hours I only charge 75 bucks. Hobo Charlie.
Posted by:2006 scion xa in Arlington, VA. Posted:June 24th, 2016 01:06PM
Hours of Labor:2.5
Went to the dealer for an oil change, found out water pump is leaking and belt is cracking (2nd belt). Car is at 109,731 miles. Got both replaced. I love the staff at the dealer, great parts and great work
Posted by:Billy G. in Palm Springs, CA. Posted:June 16th, 2016 06:06PM
Hours of Labor:17
Posted by:KJhart in Huntington Beach, CA. Posted:April 28th, 2016 08:04AM
Hours of Labor:3-1/2
The car had new belts and hoses put on when it was driven down from Washington State, so I didn’t need those. Just had to remove radiator, air filter housing and alternator. Wasn’t too bad.
Posted by:Kãyy in Dothan, AL. Posted:April 22nd, 2016 09:04AM
Hours of Labor:3
Posted by:Lance Ross in Newport, KY. Posted:March 19th, 2016 08:03PM
Hours of Labor:3
Replaced water pump and coolentthe pump was $55 labor and coolent $205 jake did a wonderful job
Posted by:Big willie in Lebanon, IN. Posted:March 13th, 2016 12:03PM
Hours of Labor:5
Replaced my alternator and water pump as well as the belt. Saved probably around 400 or more for labor.
Posted by:VJinConcord in Concord, CA. Posted:February 4th, 2016 11:02AM
Mechanic:Advanced Auto Services Brand:
Hours of Labor:1.5
Replacement of water pump, thermostat, and serpentine belt using dealer OEM parts, not cheaper after-market parts. Feb. 2016. Said labor total would exceed 3 hours, but only charged me for 1.5 hours.
Posted by:Shaneshane in Cincinnati, OH. Posted:January 28th, 2016 05:01PM
Posted by:LMD in Houston, TX. Posted:January 22nd, 2016 03:01PM
Hours of Labor:3.5
Anti-freeze leaking, water pump swell/cracked. Mechanic quoted me the following: Water pump $57, Upper and Lower radiator hoses were soft, replaced $27 and $19. Thermostat (disposable, must be replaced when it’s overheated) $20. 3.5 hours labor. Total $634. January 2016.
Posted by:Ralondia in Grand Blanc, MI. Posted:December 2nd, 2015 09:12PM
Hours of Labor:2
Posted by:Wizzar in Harborcreek, PA. Posted:December 1st, 2015 10:12PM
Hours of Labor:2.5
Posted by:Somewhere in the sticks in Calaveras County, CA. Posted:November 9th, 2015 11:11AM
Posted by:a user in ocala, FL. Posted:October 14th, 2015 11:10AM
Mechanic:master Brand:toyota highlander
Hours of Labor:dont know
took our highlander to a toyota dealer have oil change, said i needed a water pump because it had oil all over it, no water leaks,cost me $2300.00,
Page 2 of 2-Previous12
External Resources:
  1. Nr=AND(year:2000,make:BMW,model:528i,submod
  2. Ntk=Keyword Nty=1 Dn=0 D=wat
  3. Nr=AND(year:2000,make:BMW,model:528i,submod

More Cars-Related Topics

Check Out All Costs for Cars How Much Does Wheel Alignment Cost? How Much Does Replacing a Transmission Cost? How Much Do Tires Cost?

Cost Of Water Pump Replacement In Your Car – Protect My Car

The water pump in your vehicle performs a critical purpose; if the water pump is not operating correctly, the cooling system in the vehicle will not be able to function effectively, resulting in engine overheating. Engine overheating can result in significant complications such as warping of engine parts, which can be quite dangerous. These costly repairs can be avoided if you maintain your cooling system at its optimum performance. In reality, depending on your car’s model and whose repair you choose, the cost of replacing the water pump might vary significantly.

For the most part, the component itself is affordable, costing no more than $50 or $100.

Water pumps on automobiles must be replaced every 60,000 to 90,000 miles, which is the same interval between replacements for the timing belt. Due to the fact that the water pump is located beneath the timing cover in some cars, it is sensible to repair both parts at the same time.

What Does The Water Pump Do?

Realistically, the water pump should be called the coolant pump to better reflect its function. Your water pump should be capable of pumping more than simply water! Ever! Instead, it should be circulating a mixture of 50 percent coolant and 50 percent distilled water, with tiny changes based on the climate in which you and your car live and the type of vehicle you have. What is the source of this water-coolant mixture’s circulation? Of course, I’m referring about your engine and radiator! Your automobile’s engine becomes extremely hot.

  1. It takes 495 degrees Fahrenheit to ignite the controlled gasoline explosions that take place beneath the hood, with scorching temperatures well in excess of 1500 degrees Fahrenheit.
  2. The optimal temperature for a running engine is roughly 200 degrees Fahrenheit, according to the manufacturer.
  3. As a result, how do we make those numbers work for those areas of the engine that are closest to the combusions that are occurring?
  4. At operating engine temperature, the water pump forces coolant fluid out of the radiator and into the front of the engine, where it circulates around the cylinders.
  5. From there, it will enter the head, where it will serve to cool the valves.
  6. Essentially, there is a temperature-controlled valve in the engine that senses the engine temperature and opens and closes a gauge, opening more when the engine is hotter and therefore enabling coolant to flow through the engine.
  7. The typical car water pump is really effective!
  8. Applied to your car, this corresponds to complete coolant circulation 20 times each minute.
  9. When a liquid hits the boiling point, it is no longer capable of accepting heat transfer, which means it is incapable of cooling anything.
  10. It is likely that a frozen coolant will cause the water pump to fail before causing an engine overheat.

This chemical possesses a few of characteristics that are unusual for a liquid. It has a very low freezing point of 8 degrees Fahrenheit and a very high boiling point of 386.6 degrees Fahrenheit, making it a good choice for freezing applications. As a result, it is an excellent coolant to utilize.

Replacing The Water Pump

The procedure of replacing an old water pump with a new one can be time-consuming and difficult. For this reason, it is necessary to remove a plethora of other components from an engine block before you can have access to the pump. Consequently, it is usually performed in conjunction with another maintenance item, such as engine belt replacement, which also necessitates the dismantling of the engine in order to complete. This is an excellent method of reducing work hours and, as a result, lowering costs.

This video may be useful if you want to replace your water pump yourself: If you plan to replace your water pump yourself, consider watching this video as a resource: Is it possible that individual parts of my water pump will need to be replaced?

As a result, there are no replacement components available; if your water pump is experiencing problems with a specific component, the entire unit will need to be replaced.

What Are The Signs Of A Bad Water Pump

When the water pump is tucked away and concealed in your engine block, it is tough to tell when it needs to be replaced. So how can you know when it is time to repair the water pump? In accordance with what we’ve already covered, the water pump should have a lifespan of between 60,000 and 90,000. It is fortunate that there are certain telltale symptoms that the water pump is not working correctly. If your water pump is within the expiry range specified above, you should be on the lookout for the following six signs of trouble.

  1. As we’ve described previously, the water pump is responsible for pumping engine coolant through your radiator and engine block, removing heat from the hot engine components, and avoiding warping caused by overheating. A lack of appropriate coolant circulation will cause the engine to overheat, first in a slow and gradual manner. Whining sounds: If you hear a whining sound emanating from your engine block, it might be due to a loose or faulty water pump belt in your vehicle. High-pitched whines and squeals, as well as harmonic buzzes, are examples of what it might sound like when it occurs. A growling or grinding noise, on the other hand, is a sign that your bearings are in poor condition. Regardless, a technician should be called in to diagnose and repair any problems that arise. If you can see muck under your hood and it is obviously dried up engine coolant, you most likely have a leaking engine coolant system. Despite the fact that it may be a gradual leak and the amount of engine coolant that makes it to the ground may be tiny, you should have a professional look it over. A similar issue to what you read on our gunk “tale,” leaking will be the same problem, but it will be more severe to the point where you will have pools of fluid under your car. In contrast to AC condensation and leaking, this fluid will be either orange or green in color depending on the type of coolant your car uses and the temperature outside. If you discover this problem, you should bring your automobile in as soon as possible. Due to the fact that engine coolant is harmful to both humans and animals, please exercise caution and do your bit to clean up the mess. In many cases, overheating of the engine is the most prevalent symptom of a malfunctioning water pump. Having your car pulled into a reputable repair and having this issue evaluated as soon as possible can help to minimize engine warping due to heat accumulation. Whatever you do, do not attempt to start the car. Steam: If your engine is smoking or steaming, it is likely that your vehicle is operating at an excessively high temperature. The interior components of your engine block have most likely already suffered some damage as a result of your actions up to this point. It is critical that you pull over and turn off your vehicle as soon as possible if this occurs in order to prevent further harm. Make sure your engine has completely cooled down before you begin to poke around beneath the hood of your vehicle. Call a tow truck and prepare yourself for some expensive repairs

Can I Drive My Car With A Bad Water Pump

Inadequate coolant circulation: As we’ve described previously, the water pump is responsible for pumping engine coolant through your radiator and engine block, removing heat from those hot engine parts, and avoiding warping caused by excessive heat. If the coolant does not circulate correctly, the engine will begin to overheat, first at a modest pace. It’s possible that the water pump belt is loose or broken if you notice a whining coming from your engine block, and it’s the cause of the noise.

  • A growling or grinding noise, on the other hand, is a sign that your bearings are in poor condition.
  • If you can see muck beneath your hood and it is clearly engine coolant that has dried out, you most likely have a leak.
  • A similar issue to what you read on our gunk “tell,” leaking will be the same problem, but it will be more severe to the point where you will have pools of fluid under your vehicle.
  • If you discover this problem, you should bring your vehicle in as soon as possible.
  • Having your car pulled into a reputable repair and having this issue evaluated as soon as possible can help to minimize engine warping caused by heat accumulation.
  • Steam: If your engine is smoking or steaming, it is likely that your vehicle is operating at an excessively high operating temperature.

In order to avoid more damage, it is critical that you pull over and switch off your vehicle as soon as possible. Make sure your engine has totally cooled down before you begin to poke about beneath the hood of your vehicle. A tow truck should be called, and expensive repairs should be expected.

What Is The Cost Of Replacing The Water Pump

Replacement of a water pump in your vehicle can cost you anywhere from $300 to $700 if you take your vehicle to a repair. The cost may vary based on where you live, what automobile you drive, and which mechanic you pick. The component in and of itself is reasonably priced. It is the cost of labor that has the most impact on the pricing. This is a time-consuming repair since the water pump is frequently hidden and requires the removal of other components in order to gain access to it. Part: The cost of a water pump is typically in the region of $50 to $100.

Labor: As previously said, it is the labor that is the most expensive component of changing this particular element.

How Long Does It Take To Replace The Water Pump

The replacement of a water pump in a normal car will take between two and three hours on average. When it comes down to it, the exact time period will vary depending on a variety of things like the make and type of your vehicle, which will determine where the water pump is placed within the vehicle and what engine will need to be removed in order to get to it. To summarize, a water pump is critical to your capacity to run your car safely and efficiently. Keep an eye out for symptoms that yours is in need of repair or replacement.

You may save thousands of dollars on auto repair expenses whether your vehicle is new or old, and whether your manufacturer’s warranty is due to expire or has already expired.

The good news is that when you get a coverage with Protect My Car, you may only have to spend as little as$100.00 for any significant repairs.

The following resources are available: oq=ethylene+glycol+free aqs=chrome0.0j69i57j0l6.8281j1j7 sourceid=chrome ie=UTF-8 sourceid=chrome

Leave a Reply

Your email address will not be published.