# How Long Does It Take A Hot Water Heater To Heat Up

## Water Heater Recovery Heat Up Times Comparison Chart

Water Heater Recovery Heat Up Times Comparison ChartWater Heater Recovery Heat Up Times Comparison ChartThere isn’t much that can spoil your day quite like taking an ice cold shower, and if you have the wrong hot water heater, this might become your new normal. Make sure you evaluate how long it will take for your new hot water heater to heat up before making your final decision. If your current heating unit is failing, don’t let the stress of the situation to push you into making the wrong decision about its replacement.

So, how long does it take a hot water heater to heat up water again after it’s been depleted?

 Water Heater Type Time to Heat Back Up Gas – Conventional Tank 30-45 mins Gas Tankless 0 mins Electric – Conventional Tank 60-80 mins Electric Tankless 0 mins

Gas Water Heaters Gas Conventional Water Heater Details Once the water is in the tank, the normal gas tank water heater will take 30 to 40 minutes to heat it up to the desired temperature. When new water from your water supply is fed into the tank, this early heat up occurs as a result of the incoming water. A more particular explanation of why this takes 30 minutes requires some mathematics. The size of the heater’s tank is obviously important, since more water will take longer to heat than a smaller tank.

• In simple terms, a BTU is the amount of heat required to elevate one pound of water by one degree Fahrenheit in temperature.
• For example, the typical hot water heating unit tank holds 40 gallons of water.
• Thirty-five gallons times 8.3 pounds per gallon is 330 pounds of water.
• For the sake of not having to go into full-blown thermodynamics calculations, we can simplify and say that a 40,000 BTU system with a 40-gallon tank requires half a minute to heat each gallon, which results in a half-hour heat up time.
• For those with larger tanks or lower BTU ratings, on the other hand, it will take longer to heat their tanks.
• Likewise, keep in mind that this is the amount of time it takes for new cold water to be heated in your tank, so plan accordingly.

When all of the warm water in the tank has been consumed, the amount of time it takes to warm up new water is taken into consideration. It will be necessary to restart the gas tank water heater at that point in order to heat new water from the incoming groundwater temperature level.

#### A gas tank hot water heater will take roughly 40 minutes to warm up new inbound water for the very first time.

Specifications for an Electric Conventional Water Heater When compared to gas tank hot water heaters, electric tank hot water heaters typically require twice the amount of time to heat water. Electric components, while often more cost-effective, are just incapable of matching the high performance of gas-fired systems. It would take approximately one hour for an electric hot water heater to heat the 40-gallon tank described above from the time brand-new water is introduced into the system. As a result, homes with higher water demands are more likely to opt for a whole-house gas tank water heater rather than an electric model.

1. A tank hot water heater that uses electricity takes 60-80 minutes to heat water, whereas a tank hot water heater that uses gas takes 30 minutes.
2. Unless the system is malfunctioning, this should not take more than a few seconds for a typical-sized house to complete the cycle.
3. Due to the fact that a tankless gas heater heats water immediately, it should only take a few seconds for that warm water to travel through the pipes and into the component.
4. For the most part, water does not become heated until the dishwashing machine or hot water faucet is turned on.
5. Due to the fact that a tankless electrical heater warms water fast, it should only take a few seconds for the warm water to make its way through your pipes and into your fixture.

In summation, there’s a heater suited for everyone out there. Consider your requirements before selecting a storage tank, whether traditional or tankless in design. South End Plumbing specializes inall plumbing services, so remember, we are just a click away.

We also specialize intankless water heaters– give us a call! South End Plumbing is one of the only firms that will offer you a free estimate. Call us at704-919-1722or fill out theform onlineto book a visit.

## How Long Does it Take for Electric & Gas Water Heaters to Heat Up?

An ice cold shower is one of the few things that can completely derail your day, and if you have the wrong water heater, this could become your new normal. If your present heater is on its last legs, don’t allow the stress of the circumstance push you into making the wrong decision about your new heater. Before you purchase a water heater, take into consideration how long it will take for your water heater of choice to reach operating temperature. If you want to run a large amount of hot water at the same time, you’ll need a more powerful system than if you merely want to take a hot shower on a consistent basis.

While there are numerous factors which might impact the duration, the table below illustrates how long each type of water heater takes to heat up on average.

## How Long It Takes A Water Heater to Heat Up For The First Time

Water Heater Type Time Takes to Heat Up
Gas Tank 30-40 minutes
Gas Tankless 0 minutes *
Electric Tank 60-80 minutes
Electric Tankless 0 minutes *

*If the tankless water heater is properly sized and installed, it can provide almost instantaneous heat. Source of the graph

## How Long Does it Take for a Gas Water Heater to Heat Up?

Once the water has entered the tank, the normal gas tank heater will take around 30 to 40 minutes to heat it. When you first fill the tank with water from your plumbing supply, the tank will heat up for a few minutes. A more detailed explanation of why this takes 30 minutes necessitates the use of mathematics. The size of the heater’s tank is obviously important, since more water will take longer to heat than a smaller tank. The second key element is the heater’s BTU (or British Thermal Unit) rating.

1. A heater with a higher BTU rating will heat water more quickly.
2. Each gallon of water contains approximately 8.3 pounds of water; as a result, our example tank contains approximately 330 pounds of water to heat.
3. If the water is at 60 degrees and you want to bring it up to 120 degrees, you will need to raise the temperature by 60 degrees to do this.
4. If you have a smaller tank or greater BTU rating, your hot water heater’s warm-up time will be shorter.
5. You will need to keep the following criteria in mind if you want a high-efficiency water heater that will heat your water in the period of time you specify (after it has run out of hot water) and hold a significant volume of hot water.
6. The first time you switch on the hot water after your tank has been holding hot water for a while, you should get hot water in a matter of minutes because tanks store pre-heated water, not minutes or hours.

That’s when the gas tank water heater will have to start heating new water from the temperature of the entering groundwater again, which will take longer. In order for a gas tank water heater to heat up new incoming water for the first time, it will take roughly 30 minutes.

## How Long Does it Take an Electric Hot Water Heater to Heat Up?

When compared to their gas counterparts, electric tank water heaters typically require twice the amount of time to heat water. Despite the fact that electric elements are typically more cost-effective, they cannot compete with the high performance of gas-fired systems. It would take approximately one hour for an electric water heater to heat the 40-gallon tank described above from the time new water is introduced. As a result, residences with higher water needs are more likely to choose for a whole-house gas tank water heater rather than an electric type.

When it comes to heating water, an electric tank water heater takes 60-80 minutes, compared to 30 minutes for a gas tank water heater.

## How Long Does it Take a Tankless Gas Heater To Warm Up?

Tankless water heaters heat your water on demand, which means that the distance between your heater and the appliance you are using is the only factor that determines how long it will take for you to receive hot water from your faucet. Ideally, this should not take more than a few seconds with a typical-sized house if the system is functioning properly. With a large home, it may take a few more seconds to travel through the water pipes and reach appliances further away from the heater. Because a tankless gas heater heats water instantly, it should only take a few seconds for the hot water to travel through your pipes and into your fixture after being turned on.

## How Long Does it Take a Tankless Electric Heater To Warm Up?

Considering that tankless water heaters heat your water “on demand,” the only factor that decides how long it will take for you to obtain hot water from your faucet is the distance between your heater and the item you are using. Ideally, this should not take more than a few seconds for a typical-sized house if the system is functioning correctly. It may take a few extra seconds for the water to travel through the water pipes and reach appliances that are located further away from the heater in a large home.

## Factors That Affect Heat Up Time

Apart from the variables we’ve already covered, such as tank size and BTU rating, there are a variety of other factors that can influence how long it takes your water heater to heat water for the first time.

• Temperature of the incoming water– For both tankless and tank-style water heaters, the temperature of the incoming water will play a role in determining the amount of time it takes to heat up. Because tank heaters store water and keep them heated, the incoming temperature shouldn’t affect it so greatly. Instead of storing water in tanks, tankless heaters deliver incoming water on demand, just moments before it comes out of your faucet. This implies that if the groundwater temperature is really low, the water may not get as heated as fast. Neither type of heater is impervious to the effects of extremely cold ambient temperatures in the room or area where they are stored
• However, the former is more vulnerable. Settings– Although water heaters seem relatively simple when compared with other household mechanicals, they often have more to them. If your heater isn’t working, a professional may need to come to check out any settings or calibration that could be negatively impacting its performance
• Maintenance / Expenditure Issues– In the same way that any other mechanical equipment ages and degrades over time, the age and condition of your heater may eventually impact its performance, including how long it takes to heat up. A lack of routine maintenance, particularly a failure to wipe out silt that may have accumulated in the pipes, might also result in performance problems. Those who live in areas with hard water are more likely to encounter pipe sediment. Distance from Appliance– Sometimes it’s easy for the end user to forget, but your hot water is going from the ground, via the heater, and pipes in your home before reaching the appliance you are using. The greater the distance between your appliance and the water heater, the longer it may take for the hot water to reach it. This should be taken into consideration by a knowledgeable installation when setting up your system, so it should not be a significant problem. Pipe Diameter– In addition to the length of the piping, the width of your water pipes may have an impact on how long it takes for the water heater to heat up completely. The use of a wider pipe is advantageous because it can carry more water
• However, it will require more water to be heated before the pressure is high enough to force the water through the remaining pipe system.

In conclusion, there is a heater out there that is perfect for everyone. Be sure to consider your requirements before selecting either a traditional tank or a tankless system. See our review of the best models on the market now that you know how long it takes for both gas and electric water heaters to heat up. With great brands like Bosch, Rheem, and Takagi, you’re sure to find something that works for your needs!

## How Long Does It Take for a Water Heater to Heat Up?

You are here:Home/Homeowners/Systems/How Long Does It Take for a Water Heater to Heat Up?

How Long Does It Take for a Water Heater to Heat Up? “Can you tell me how long it takes for a water heater to heat up?” you might wonder. ” Look no further — our comprehensive guide provides answers to this and many other questions. Continue reading to find out everything you need to know.

• Approximately how long does it take for a gas water heater to come to temperature. Is it possible to tell how long it takes an electric water heater to heat up
• What factors influence heating time

Request a Quote Plumbers in your area can be found here. To assist you in locating local plumbers in your region, we have teamed with Networx. To receive a no-obligation estimate, please complete the form below. Find a Plumber in your area. We may receive a commission if you click on this link, but there is no additional cost to you.

## How Long Does It Take for a Water Heater to Heat Up?

Request a Price Estimation Plumbers in Your Area To assist you in finding local plumbers in your area, we have teamed up with Networx. To obtain a FREE quotation, please see the link below. Locate a Plumbing Professional You will not be charged any further fees if you choose to click on this link.

### How Long Does It Take a Gas Water Heater to Heat Up?

A gas water heater is more energy efficient and can heat water more quickly than an electric water heater. With powerful burners located at the bottom of the tank, they use natural gas as a fuel to heat the water stored in the tank. The temperature at which a gas water heater is set, as well as the temperature of the cold water that it must heat, determine how quickly it can heat water. Here are several averages to consider:

• Gas water heaters with capacities of 40 and 50 gallons take 30-45 minutes, and 80-gallon gas water heaters take 60-70 minutes to heat.

The average gas water heater holds around 40 gallons of water and takes approximately 30 to 40 minutes to heat water from 40 degrees to 120 degrees. It will take around 40 to 50 minutes to heat up a 50-gallon unit. It takes around 60 to 70 minutes for a big 80-gallon gas water heater to reach operating temperature. Of course, this is only a rough estimate, and actual costs may vary depending on the age and model of the vehicle.

### How Long Does It Take an Electric Water Heater to Heat Up?

Electric water heaters require more time to heat up than gas water heaters. To heat the water, these units make use of electrical heating elements that are submerged within the tank. They require approximately twice the time to heat up. The amount of time it takes is affected by the wattage of the heating element and the temperature that has been set on the water heater. Here are some averages, on the other hand:

• 40-gallon electric water heaters take 60-80 minutes to heat water
• 50-gallon electric water heaters take 145-150 minutes to heat water
• 80-gallon electric water heaters take 120-130 minutes to heat water.

If you have a 40-gallon electric water heater that uses 5500 watts and is set to 120 degrees, it will take around an hour to an hour and 20 minutes to heat the water. It will take approximately an hour and 45 minutes to an hour and 50 minutes to heat a 50-gallon electric unit. It will take around 2 hours for a big, 80-gallon electric water heater to reach the desired temperature.

## 6 Factors That Affect Water Heating Time

With a 40-gallon, 5500-watt electric water heater set to 120 degrees, heating time will be around one hour to one and a half hours to complete. It will take around one hour and 45 minutes to one hour and 50 minutes for a 50-gallon electric unit to reach operating temperature (see chart). It will take around 2 hours for a large electric water heater (80-gallon capacity) to heat the water.

### First-Hour Delivery Rate

A rating for first-hour delivery (FHD) is given to all water heaters. When the water heater is fully charged, the FHD tells how many gallons of hot water it can deliver in an hour. The flow rates for FHD are provided in gallons per hour (GPH).

A high FHD rate indicates that you will receive more hot water more quickly than you would from a unit with a lower FHD rate, which means you will save time and money. A FHD rate of around 60 to 80 GPH is appropriate for a 50-gallon container.

### Recovery Rate

The recovery rate of a water heater refers to how many gallons of hot water the device can deliver each hour while it is being utilized. It informs you how quickly the water heater can recover (also known as refill) with cold water and heat it back up to normal temperature. Due to the fact that it takes less time to heat up hot water in a unit with a high recovery rate, it will supply hot water faster. A high recovery rate water heater, on the other hand, will be able to swiftly heat cold water that enters the system, regardless of how much hot water you’re consuming at once.

### Power Source

The power source of a water heater (gas or electricity) has a significant impact on the amount of time it takes to heat water. Electric water heaters are notorious for taking a long time to heat the water. This is due to the fact that using electrical heating components rather than gas burners is less efficient. A typical 50-gallon gas water heater may have a flow rate of 80 to 90 GPH, but an average 50-gallon electric water heater may have a flow rate of 58 to 66 GPH, depending on the model.

### Water Heater Type

Those with tanks that store and heat water are referred to as storage water heaters. Tankless water heaters do not have storage tanks and heat the water as soon as it is drawn from the faucet, saving energy. These two types of water heaters have a significant variation in the amount of time required to heat water. It might take anything from 30 minutes to an hour and a half for a storage water heater to reach operating temperature. A tankless water heater, on the other hand, makes hot water accessible almost immediately.

Continue reading: The Best Tankless Water Heaters

### Water Heater Size

The size of a storage water heater, measured in gallon capacity, has a significant impact on how rapidly it can heat water. Storage water heaters may typically hold anywhere from 30 to 80 gallons of water, depending on the model. Smaller tanks heat water more quickly (and run out of hot water more quickly) than larger tanks because there are fewer gallons of water to heat. This is analogous to heating water in a tiny 2-qt. saucepan on the stove instead of a large 12-qt. stock pot on the stove.

Larger tanks, on the other hand, do not take as long to heat up as you might expect.

Because large capacity gas water heaters feature a larger gas burner, they heat water faster than smaller capacity gas water heaters.

Even so, if you have a 30-gallon water heater, you won’t have to wait nearly as long for it to heat up as you would if you had a 50- or 80-gallon one. Continue reading: The Best Small Water Heaters

### Original Water Temperature

The temperature of the starting water has a significant impact on the amount of time it takes for a unit to heat it up. If the water temperature at the input is low, the water heater will have to work harder to increase the water temperature to the setting you’ve selected. Temperatures in cooler areas are typically about 40 degrees Fahrenheit for the water entering the system. In warmer areas, the temperature is around 50 degrees. It takes some time for the water heater to heat the water from 40-50 degrees to 140 degrees.

To assist you in locating local plumbers in your region, we have teamed with Networx.

Find a Plumber in your area.

## So, How Long Does It Take for a Water Heater to Heat Up?

In most cases, if you have a gas water heater set to 120 degrees and the incoming water is about 50 degrees, you should not have to wait more than 30 to 50 minutes for hot water (in 40 and 50-gallon units). A 5500-watt electric water heater set to 120 degrees will provide hot water after about 50 minutes if the incoming water temperature is roughly 50 degrees. This will require a little longer wait time. It will take approximately one hour to one hour and forty-five minutes (in 40 and 50-gallon units).

If your water heater takes longer than around 2 hours to heat up, you should contact a professional to inspect it.

###### You Might Also like:
• What size water heater do I require
• What is the average cost of a water heater
• And how long does a water heater last

## How Long Does It Take a Water Heater to Heat Up?

Are you in the market for a new water heater but are unsure of how to select the most appropriate model for your requirements? Do you regularly run out of hot water in the middle of a shower and wonder what you can do to fix the problem? Let’s have a look at how long it takes a water heater to heat up in real life. In every family, water heaters serve a crucial function; without them, we wouldn’t have enough hot water for our everyday activities. However, they are not magic machines that can produce an unlimited supply of water, and the rate at which they heat up is dependent on a variety of factors.

## How Long Does It Take a Water Heater to Heat Up

In terms of water heaters, there is a tremendous range of sizes, styles, and fuel or power sources to choose from. All of these factors have an impact on the time it takes for the water heater to heat up.

### Gas Water Heaters

Natural gas boilers are one of the most efficient and long-standing methods of heating water in a household. For a long time, gas has been a popular source of energy. One of the advantages is that energy expenses are kept to a minimum. As an alternative to employing electric components, they heat the water with gas burners that are located at the bottom of the storage tank. As a result, their recuperation period is much shorter.

Generally speaking, a standard gas water heater does not take long to heat a full tank of water, however the time may vary depending on the size. A 40-gallon tank will fill in 30 to 40 minutes, and an 80-gallon tank would fill in 60 to 70 minutes, depending on the size of the tank.

### Electric Water Heaters

Electric water heaters are somewhat less efficient than gas water heaters. These make use of electric heating components that are contained within the tank, similar to a toaster or an oven. The recovery period of these units is somewhat longer than that of gas-fueled machines. If you have a 40-gallon tank, you may anticipate to get hot water in between 60 and 80 minutes. You’ll get hot water in around two hours if you have an 80-gallon storage tank.

### Solar Water Heaters

Electric water heaters are a little less energy efficient than gas water heaters, for instance. As with a toaster or an oven, these employ electric heating components that are housed within the tank. In comparison to gas-fueled devices, their recovery period is slightly longer. It takes 60 to 80 minutes to heat 40 gallons of water, depending on the temperature of your water heater. You will have hot water in around two hours for an 80-gallon tank.

## Factors That Influence Heating Time

The anticipated waiting time is merely a best-guess estimate at this point. Water heaters are impacted by a variety of factors, all of which can have an impact on how long it takes for them to heat up. Some are ubiquitous across all sorts, but others are more specialized to a single type only.

### 1.First Hour Rating

It is indicated by the first hour rating that the water heater can supply a certain number of gallons within the first hour of operation. It displays the water heater’s capacity to return a full tank to the proper temperature once it has recovered from a power failure (4). A high ranking for the first hour indicates a lower waiting time. In order to determine this value, we need to know the fuel source, tank capacity, and size of the heating components or burners (5).

### 2.Size of Water Heater

The size of your water heater is another element that might affect how long it takes to heat water. As you can see from our previous samples, a greater tank size requires more time to heat up. This is simply due to the fact that there is more water to heat. Larger tanks would often feature two heating elements or a huge burner to reduce the amount of time it takes to heat up. Despite this, a smaller tank will heat up more quickly. Having said that, the smaller tank will almost certainly run out of fuel sooner than the bigger ones.

### 3.Inlet Water Temperature

Another element that can have a significant impact on recovery time is the temperature of the incoming water, often known as temperature increase. It is possible that the inflow water will be at a different temperature depending on where you reside. Generally speaking, the weather is cooler in the North than it is in the South. We refer to the temperature disparity between the entering water and the temperature that has been established on the boiler as “temperature increase.” The colder the intake water is, the longer it will take for the water to heat up to the proper temperature.

### 4.Fuel Type

As you can see from our previous examples, the kind of fuel makes a significant impact in recovery time.

When it comes to heating water, gas water heaters are significantly faster than their electric counterparts. This is due to the fact that gas burners attain temperatures that are far greater than those of electric heating components.

## Why Is It Suddenly Taking Longer?

Over time, it is likely that your water heater may take longer to heat up. However, if it occurs too soon, keep the following in mind:

### 1.Sediment Buildup

Sediment accumulation is the most likely cause of your water heater’s unexpected inability to heat water quickly. This is a frequent problem that occurs over time as your machine becomes older. Although it is possible that it will occur sooner if you have hard input water or if you ignore upkeep. When the minerals contained in the water begin to settle on the inside of the tank, this is referred to as sediment building. The phenomenon can occur even with soft water that is low in minerals, although it will often take a bit longer before it becomes evident.

These are located on the tank’s walls and around the heating components, where they can severely impair the tank’s capacity to heat the water in it.

• The unit takes slower to heat up, and you’ll run out of fuel far more quickly than you did previously
• There are weird noises coming from the device, such as popping, banging, or hissing. Increased energy bills by a significant amount

The most effective method of resolving this problem is to cleanse the tank on a regular basis. If, on the other hand, you have an electric unit and the heating elements are broken beyond repair, you will need to have them replaced.

### 2.Needs Troubleshooting

If sediment accumulation isn’t the problem, it’s possible that the heating components or the thermostat need to be checked out for problems. If you have an electric heater, this is a rather simple technique; but, if you have a gas heater, you’ll need some prior knowledge. This is also one of the reasons why we advocate consulting with a professional. If your unit is powered by electricity, the following is a basic description of how to troubleshoot:

• Turn off the electricity: Before you handle any electrical components, make sure the breaker is in the “Off” position. To gain access to the thermostat, follow these steps: Using a screwdriver, remove the access panel from the wall. Afterwards, carefully remove the insulation to reveal the upper thermostat. Check the battery’s capacity: Make use of a multimeter to check for indicators of voltage on the cables. Before you proceed, make sure that they all have a reading of zero. Adjust the temperature as follows: To adjust the temperature, use a flat-bladed screwdriver to turn the arrow displaying the temperature. Reduce the temperature by a few degrees to see if it helps. To sum it up: Insulation and the access panel should be replaced. When you’re ready, switch on the breaker to bring your water heater back to life.

Alternatively, if the recovery time is still too slow, it is possible that the heating components need to be replaced. Another possibility is that your water heater is just not large enough to meet your hot water requirements.

## This Took a While…

The amount of time it takes for a water heater to heat up is dependent on a number of things. Generalization: Gas-powered devices are substantially faster than electric-powered ones. On the other hand, it is possible that the recovery time abruptly rises, which might be an indication of silt accumulation. If this is the case, flush the tank or contact a professional for assistance with a new system. How long does it take your water heater to get to temperature? We’d love to read your responses, as well as any additional questions you may have.

## How Long Will It Take a Water Heater to Heat Up?

There are a variety of elements that might influence the recovery time of a water heater, as well as how quickly it heats up. The most important things to think about are as follows:

• Temperature increase
• Energy source for the water heater
• Water heater size
• First hour rating

Before purchasing a new water heater, take the time to conduct thorough research. If having hot water as quickly as possible is essential to you, continue reading to understand how the type of water heater you choose can effect how quickly you will have hot water.

## How Long Does It Take for Hot Water to Come Back with Certain Types of Water Heaters?

Time required to heat water varies; it may take as little as a few seconds or as long as 60–80 minutes.

Whatever sort of water heater you have will determine how much heat you will receive. Here are some typical heat-up times for different types of water heaters, assuming that the equipment are new and appropriately sized for the home: 1.

• Depending on the temperature of the water, it may heat up instantaneously or it may take 60–80 minutes to reach the desired temperature. Whatever sort of water heater you have will determine how long it will take to heat the water. If the appliances are fresh and correctly suited for the residence, the following are some typical heat-up periods for various water heaters: a.

Keep in mind that these are the lengths of time it takes to heat new cold water that is introduced into the water heater’s storage tank. Storage tank water heaters are self-contained appliances that regularly replenish themselves and heat water for when they are needed. However, if you use up all of the hot water (for example, after a busy morning with many showers), you’ll be kept waiting for additional hot water as your appliance refills from the tank’s empty position. Without a propane tankless water heater, which warms water on demand, it’s possible that you’ll be without hot water during high usage periods.

### Conventional Gas Tank Water Heater

When starting with an empty tank, a standard gas tank water heater, such as one fueled by propane, can take up to 30–40 minutes to heat the water to the desired temperature.

### Gas Tankless Water Heater

When it comes to households with moderate to high hot water consumption, propane tankless water heaters are a popular choice. When properly sized and placed, they have the ability to quickly heat water on demand, delivering hot water in a matter of seconds when needed.

### Conventional Electric Storage Tank Water Heater

One of these appliances might take up to 60–80 minutes to heat water, depending on the model. The use of electricity to heat water is not as efficient as the use of propane, thus it is only a viable choice for small households with low water heating requirements.

### Electric Tankless Water Heater

These systems, like propane tankless water heaters, heat water on demand, allowing for quicker supply of hot water than storage tank units. However, they will still take a little longer to heat up than propane does.

### Solar Water Heater

These systems, like propane tankless water heaters, heat water on demand, allowing it to be delivered more quickly than storage tank equipment. They will, however, take a little longer to heat up than propane does.

## Other Factors That Can Affect Water Heater Recovery Time

Aside from the kind of water heater, there are a variety of other elements that might influence how quickly your water heater produces hot water.

• Water heater size: If you regularly find yourself without enough hot water in your home, it is possible that your water heater is too small for your requirements. Be sure to learn about how to size a water heater while you’re researching which water heater is best for your needs. Rating for the first hour: This is the maximum number of gallons of hot water that a unit can deliver each hour, starting with a completely full tank of water. Check the water heater’s manufacturer’s information to ensure that the first-hour rating of the water heater will suit your demands during peak consumption periods. Dimensions of the house: If your water heater is located a great distance away from the appliances or fixtures that require hot water, it may take longer for the hot water to reach those appliances or fixtures as it travels through the pipes. Pipe diameter (inches): Smaller pipes are incapable of transporting as much hot water as larger pipes. The water heater’s age and condition are as follows: Over time, the efficiency of water heaters decreases. Considering that one year for you is equivalent to ten for your water heater, it’s possible that yours is older and less efficient than you believe, and that it’s delivering less hot water than it should be. How long has your water heater been in service?

## If Your Water Heater Heats Water Too Slowly

Do you live in a house where you have to wait an inordinate amount of time to receive hot water when you need it? It might be caused by any of the difficulties listed above, or it could be the result of a condition that requires expert treatment. Consult with a knowledgeable specialist, such as a plumber or a propane provider, about your circumstances to ensure that you have enough hot water to keep yourself comfortable.

It’s critical to understand how to properly size a water heater before making a purchase to ensure that you never run out of hot water. Are you interested in having hot water available on demand? Learn more about the advantages of tankless water heaters by reading the following article.

## How Long Does a Water Heater take to Recover?

Take a wonderful, warm shower when the water suddenly becomes ice cold, which is a really unpleasant sensation to experience. When will your hot water be able to be accessed again? Alternatively, perhaps this is a recurring trend, and you are perplexed as to what is causing it. It all relies on the recovery rate of your water heater, which is the amount of time it takes to reheat the water tank once it has been depleted. On average, it might take anywhere from 1-2 hours for an 80-gallon tank water heater to recover from a power failure.

It should be noted that this is only a rough estimate. Several factors will be discussed in this article to assist you in making a more specific estimate of how long your water heater will need to recover. These factors include:

• Recovery timings for a typical water heater
• Key elements that impact recovery times for a typical water heater
• Common difficulties that cause recovery times to be delayed

Is your water heater taking an excessive amount of time to recover? Red Cap PlumbingAir can provide you with a water heater repair that is both rapid and efficient. We promise that our skilled plumbers will arrive on time, and in most situations, we will be able to repair your water heater the same day that we identify the problem!

## Average Water Heater Recovery Times

Consider the typical recovery time for a water heater and what is considered a “fast” recovery time for a water heater. You will be able to tell immediately if yours is taking substantially longer than normal. An 80-gallon tank with entering water temperature of 62 degrees, for example, will typically recover in the following amount of time:

• 60-70 minutes (for a gas tank water heater)
• 120 minutes (for an electric tank water heater)
• 60-70 minutes (for an electric tank water heater).

You’ll notice that gas water heaters can heat your water far more quickly than electric water heaters. It heats water more quickly because gas water heaters employ burners that reach greater temperatures more quickly than the heating coils in electric water heaters, resulting in quicker heating. Having said that, they are only fast averages for comparative purposes. Several important elements, which we’ll explore next, influence the recovery time of your individual water heater, resulting in a recovery rate that may be greater or lower than the national average.

## Key Factors That Influence Water Heater Recovery Times

The recovery time of your water heater will be greatly influenced by several aspects, including the tank size, first hour rating, fuel type, and temperature increase. Let’s take a closer look at each of these elements in greater depth below.

### 1. Tank size

The tank size and First Hour rating of your water heater may be found on the Energy Guide label on the appliance. / Source: Federal Register In general, the higher the tank capacity of your water heater, the longer it will take for it to recover. The majority of home water heater tanks have a capacity of 20 to 100 gallons or more. If your water heater is on the bigger side, it will take longer for the burners or heating elements to get the water up to the desired temperature. Furthermore, as your tank is nearing the end of its supply, recuperation durations for larger tanks become considerably longer.

### 2. First hour rating

The “first hour rating” of any tank water heater is based on the fact that the tank is continually renewing its water supply. This rating informs you how many gallons of water the unit can supply in one hour when it starts with a full tank of hot water. The first hour ratings are based on a variety of criteria, including your heating source, burner size, and others. In general, though, the higher your first-hour rating, the faster you may anticipate your water heater to recover from the damage it has sustained.

Examine the label on your water heater that says “Energy Guide.”

### 3. Fuel type

When compared to gas water heaters, electric water heaters take nearly twice as long to restore their heating capacity. Why? Because gas water heaters use gas burners, which can achieve greater temperatures more quickly than electric heating coils, they are more energy efficient. Despite the fact that it is more expensive to install, a gas water heater is extremely energy-efficient, and you will not be without hot water for lengthy periods of time. If you want hot water quickly, it may be worthwhile to make the expenditure.

If you already have gas lines in place, you will save money on installation charges. Additionally, gas water heaters are less expensive to maintain since natural gas is more economical as a fuel than electricity, especially in Florida, which is one of the top natural gas producers in the country.

### 4. Temperature rise

The temperature rise is influenced by the hot water temperature you like. The temperature of the water in your location will vary depending on where you live and what kind of climate you have. As a result, while estimating the recovery of your water heater, it is critical to account for “temperature rise.” The difference between the temperature of the entering water and the temperature you want your water to be is referred to as the temperature increase. The greater the disparity between the two, the longer it will take for the water heater to recover.

If you are a homeowner in the Tampa region, you should know the following:

• It is estimated that your incoming water temperature will be around 72 degrees
• Your targeted hot water temperature is 120 degrees
• And

It is estimated that your incoming water temperature will be around 72 degrees; your ideal hot water temperature is 120 degrees.

• The temperature of the entering water is around 47 degrees
• Use the same intended water temperature of 120 degrees for the remainder of this discussion.

According to our calculations, the temperature would climb by 73 degrees Fahrenheit. When compared to the Tampa example, this is nearly a twofold increase in temperature, which means the New Hampshire homeowner’s water heater will have to work twice as hard to heat their water as before.

## Common Problems That Slow Down Recovery Time

When sediment accumulates at the bottom of your water heater, contact a plumber to have it flushed thoroughly. / Image courtesy of St. Cloud State University Even if you have the most energy-efficient water heater available, you may still experience difficulties that cause the heater to take longer to recover from. The following are examples of common issues:

### Sediment buildup:

It is caused by the dissolved minerals in your water (calcium and magnesium) settling to the bottom of your water heater, which is known as sediment building. Over time, this results in the formation of a thick, crusted coating that might impair the ability of your water heater to heat water.

### Broken dip tube:

The dip tube is a component of a water heater that directs incoming cold water to the bottom of the tank where it may be heated. In the event that the dip tube fails, incoming cold water will mix with hot water, lowering the total temperature of the water.

### Worn heating elements:

Depending on the cause of the failure (normal wear and tear or damage), your tank water heater may have difficulty regaining its previous performance.

### Incorrect sizing:

If your water heater has consistently taken an excessive amount of time to reheat, your water heater is most likely too small for your requirements. The tank will never catch up and fully recover if the water heater is too small for your household’s or heating demands. This is because you are drawing too much water from the tank and it will fast empty. Contact a professional plumber to examine and flush your unit if you are experiencing any of the difficulties listed above with your hot water heater.

## Water Heater Taking Too Long To Recover? Call Red Cap PlumbingAir.

Red Cap plumbers are standing by to assist you in getting hot water more quickly. Simply contact Red Cap for a water heater repair if you believe your water heater recovery time is too short or if you aren’t sure. We will inspect your water heater, diagnose the problem, and resolve it in a short period of time. If your water heater is running too slowly for your liking and you’d want to upgrade, we’ll provide suggestions for a tank water heater, a tankless water heater, or a solar water heater that will fit your budget and meet your hot water requirements.

Call us at (813) 963-3056 (Tampa) or (727) 474-8287 (Pinellas) or use our online scheduling tool to make an appointment.

## How Long Does it Take a Gas Water Heater to Reheat?

Home-made gas water heaters can be a cost-effective way to ensure that a household has enough hot water on hand. Water heaters powered by electricity can have much higher energy costs in some places, and these devices are more prone to power outages than water heaters powered by gas (natural-draft or otherwise). if (sources.length) then this.parentNode.removeChild(sources); then this.onerror = null; this.src = fallback; )(, arguments.target.currentSrc.replace; )(, arguments.target.currentSrc.replace; )(, arguments.target.currentSrc.replace; (//\$/, “), (//\$/, “), ‘/public/images/logo-fallback.png’) is a fallback logo image.

## BTU

Household gas water heaters are a cost-effective way to ensure that a home is always well-supplied with warm drinking water. Water heaters powered by electricity can have much higher energy costs in some places, and these devices are more vulnerable to power outages than water heaters powered by gas (natural-draft). (this.parentNode.removeChild(sources); else this.parentNode.removeChild(sources); if (this.onerror = null; this.src = fallback; if (this.onerror = null); else if (this.parentNode.removeChild(sources); The slash character (//\$/, “) indicates that the character is a slash.

Working by a water heater is an IT technician To figure out how rapidly a gas water heater can raise the water’s temperature, you’ll need to do a little algebra.

## Tank Size and Thermostat Setting

if (sources.length) then this.parentNode.removeChild(sources); if (sources.length) then in the alternative, if (this.onerror = null; this.src = fallback; )(, arguments target current src replace (//\$/, “), (//\$/, “), ‘/public/images/logo-fallback.png’) is a fallback logo image. ” loading=”lazy”> ” loading=”lazy”> One gallon of water weighs 8.338 pounds when the temperature is 62 degrees Fahrenheit. At this temperature, a 40-gallon water heater would have 333.52 pounds of water in it, according to the manufacturer.

Using a thermostat set at 122 degrees Fahrenheit, it would take around 30 minutes to heat the tank completely if all of the heat were transmitted to the water.

## Tank Efficiency

if (sources.length) then this.parentNode.removeChild(sources); if (sources.length) then alternatively, if this.onerror = null, this.src = fallback; )(, arguments.target.currentSrc.replace(), ‘/public/images/logo-fallback.png’), ‘/public/images/logo-fallback.png’) otherwise ” loading=”lazy”> ” loading=”lazy”> It is estimated that 20% of the heat from the burners escapes through the chimney based on an 80 percent energy efficiency rating for the water heater.

This results in an increase of roughly 36 minutes in the time required to reheat a 40-gallon water heater operating at 40,000 BTUs.

## Age of the Water Heater

if (sources.length) then this.parentNode.removeChild(sources); if (sources.length) then if (this.onerror = null; this.src = fallback; if (this.onerror = null; this.src = fallback; if (this.onerror = null; if (this.onerror = null; if (this.onerror = null; if (this.onerror = null; if (this.onerror = null; if (this.onerror = null; if (this.onerror ‘/public/images/logo-fallback.png’) is a fallback logo image.

” loading=”lazy”> ” loading=”lazy”> The state of the unit and the amount of build-up within the tank can both have an impact on the efficacy of the burner.

## The Drip Cap

• Gas water heaters may be a reliable source of hot water for a household
• Yet, they can be expensive. It would take approximately 30 minutes to heat the tank if all of the heat was transferred to the water
• However, if the flame is not as hot due to incorrect air to gas ratios or if there is a build-up of calcium and lime in the tank, the amount of heat that is transferred to the water is reduced, resulting in an increase in the amount of time it takes to heat the water.

## How Long Should a 50-Gallon Water Heater Take to Heat Up?

Several factors, including the type of heating element used in the hot water heater and the temperature of the water that is fed into the unit, contribute to the length of time it takes for the water to heat back up after the tank has been exhausted. In order to measure the efficiency of a water heater, it is necessary to look at two different ratings: recovery and first-hour ratings. Both of these ratings are important because they influence the amount of time it takes to heat the water in the heater.

Maintaining your hot water heater on a regular basis can help to keep it running efficiently.

## Draw Efficiency

The draw efficiency of both gas and electric heaters is calculated on the basis of a formula that accounts for 70% of the total storage tank capacity. It is possible to get 35 gallons of use from a 50-gallon hot water heater since cold water replaces hot water throughout the heating process. A 50-gallon hot water heater is ideally suited for three-bathroom homes or for a household with two bathrooms and a washing machine, among other applications. Washing machines require 20 gallons of hot water, dishwashers demand 10 gallons, and a one-person bath takes at least 10 gallons.

## First-Hour Rating

The total amount of water drawn from the hot water heater in gallons during one hour – with the unit set to a water temperature of 135 degrees Fahrenheit – determines the unit’s first-hour rating, which is determined according to the tests specified by the United States Department of Energy for the unit. The results of the unit’s energy efficiency tests are shown on the unit’s sticker. Testers pull three gallons of hot water per minute for the duration of the test, which terminates when the drawn hot water cools to 25 degrees.

Amount of water drawn during this hour shows the hot water heater’s full-hourly capacity (FHR), which provides an indicator of how much water is available during peak use periods throughout the day.

## Recovery Rating

The quantity of electricity that the device receives is what determines its recovery rating. Gas hot water heaters are more energy efficient than electric hot water heaters, taking approximately half the time to heat up. A 50-gallon hot water heater’s heating time is determined by the temperature of the water entering the machine and the temperature setting used to heat the water, both of which are controlled by the power supply.

## Electric Hot Water Heater Recovery

It takes approximately 1 hour and 20 minutes for a 50-gallon hot water heater with 5,500-watt elements set to 120 degrees to heat water that comes into the unit at a temperature of 60 degrees. In contrast, when the water entering this same tank is 40 degrees, it takes 1 hour and 47 minutes to heat it to the desired temperature. It takes 1 hour, 6 minutes for water that is 70 degrees when it enters the tank to reach its maximum temperature of 120 degrees.

## Gas Hot Water Heater Recovery

When calculating the recovery time for an electric hot-water heater, reduce the results by two to get the recovery time for a gas unit. Water entering a 50-gallon tank at 40 degrees Fahrenheit heats up in about 53 1/2 minutes to 120 degrees Fahrenheit. In the case of 60-degree water entering the tank, the time it takes for the water to reach the 120-degree temperature is around 40 minutes. It would take 33 minutes for water that was 70 degrees.