How Do You Install A Tankless Water Heater

How to Install a Tankless Water Heater

Instructions from a professional on how to remove an old water heater tank, prepare the area for installation of a tankless water heater, and finally install the tankless water heater Because it does not store a huge amount of heated water, a tankless water heater, also known as an on-demand water heater, saves money over a traditional water heater. Essentially, it serves to give hot water on demand, so you won’t have to worry about the shower suddenly being chilly. The process of installing a gas tankless water heater consists of mounting the unit, connecting the gas and water lines, and installing a flue.

Therefore, it may not function well in a family where two or three showers may be operating at the same time, as an example.

It is both small and very efficient to use a tankless water heater.

The following skills are required if you opt to conduct the task yourself: shutting off the water to your house (seeHow to Shut Off the Water to Fixtures) and cutting into and connecting new fittings and pipes to your supply pipes (if you have copper pipes, seeCuttingJoining Copper Pipe).

There is also the need for a gas line and an electrical connection to a 120-volt circuit.

It is not necessary to vent an indoor electric tankless water heater to the outdoors because it is contained within the home.

It may either be hooked into a 240-volt outlet or directly attached to a power source such as a generator.

Tankless Water Heater Preparation

Remember to complete all essential preparations before disconnecting and removing your present water heater; you don’t want to be without hot water for a week or two while you wait for any plumbing, electrical, or vent work to be completed. If you are installing a new gas unit, you should determine whether you need to upgrade your gas meter. Because the unit consumes a considerable amount of BTUs, it is possible that your meter does not have the capacity to feed it in addition to the other gas-using appliances in your home.

  • Request that the gas provider inspect your new unit to ensure that it is receiving the appropriate amount of manifold pressure for it.
  • It is better to employ a professional plumber to install a new gas line if you need to replace an existing one.
  • This will save you time and money.
  • The fact that a tankless water heater generates a significant amount of condensation and pushes air out with a fan necessitates the installation of category II stainless-steel exhaust pipe with firmly sealed silicon joints, as seen in the second video below.
  • A damper is an excellent addition for those who live in colder climates since it prevents chilly air from re-entering the home.
  • Floor drains and utility sinks should be used to dispose of the excess liquid.
  • In addition to gas, a gas unit requires 120-volt electrical power.
  • You can watch this wonderful video from This Old House, which will provide you with an excellent explanation of the many stages involved in installing a tankless water heater.
  • He makes the decision to remove and replace his malfunctioning water heater with a tankless water heater, and he guides us through the entire procedure with his hands on assistance.
  • Codes demand that a subpanel (which may or may not be included with the unit) be erected next to the unit in order to comply.

Connect the wire to the subpanel and then from the subpanel to the unit, starting at the unit. It is essential that the electricity to the water heater’s circuit is turned off at all times while the work is being performed. +Find a Water Heater Installation Specialist in Your Area

Removing the Old Water Heater

In the majority of circumstances, a new tankless water heater will be installed in lieu of an existing storage water heater. In Ron Hazelton’s video above, he refers to our website for the directions, which are as follows: How to Flush or Drain a Water Heater (with Pictures). In order to remove the old water heater, turn off the valves on the two water lines (one for the input and one for the output) that lead into the existing water heater and disconnect them. To remove and detach the water heater’s lines from the water heater, use channel-type pliers or a pipe wrench.

  • Drain the tank by opening the drain valve located at the bottom.
  • Don Vandervort writes for HomeTips.
  • A segment or two of vent pipe should be disconnected and removed.
  • If you decide to handle it yourself, cut off the circuit at the service panel and check to be that the power has been turned off completely.
  • If you require assistance with this project, contact a local water heater professional.

Installing a Tankless Water Heater

Tankless units can be fitted flush against the wall (against the drywall or plaster), or they can be inserted into the wall between the studs. Using a stud finder, identify the studs in the wall where you want to install the unit, and then cut a hole between each of them. Attach the item to the wall in accordance with the manufacturer’s recommendations. Water supply pipes should be routed to the water heater. Make certain that the pipe from the water utility is linked to the inlet and that the pipe flowing to the home is connected to the outlet before starting the project.

  • You might also want to consider installing a pressure-relief valve.
  • The water valves should be opened, but not those for the power or gas.
  • Close the water valves and turn off the water.
  • Replace the filter, turn on the water valves, turn on the electrical power, and turn on the gas valves if necessary.

Finally, test the equipment to ensure that it is in proper functioning condition. Resource Highlighted: Find a Pre-Screened Water Heater Pro in Your AreaCall today for free estimates from pre-screened water heater professionals in your area: 1-866-342-3263

How to Install or Replace a Tankless Water Heater

Despite the fact that it’s a tankless job, someone has to do it. Leaving aside the dad jokes, installing a tankless water heater is a serious undertaking that should be approached with caution. Our goal is to make this process as simple and pleasant as possible, so we’ve included step-by-step instructions for both gas and electric units below. Take note that replacing a tankless water heater is a time-consuming process requiring advanced technical knowledge. So, if you aren’t confident in your plumbing and electrical abilities, it is preferable to engage a licensed professional – in certain areas, this is a legal requirement.

How to Install a Gas Tankless Water Heater

Installation and replacement of tankless water heaters may be quite expensive, as we realize. Installing your own unit is doable, but we recommend that you proceed with caution. This should only be attempted if you have extensive experience working with gas lines, water lines, and electrical systems. Installing your tankless water heater incorrectly might result in significant harm to your home. Unsafe gas line installation may cause explosions, while faulty gas venting can result in deadly carbon dioxide leaking into your house.

If you are considering a do-it-yourself installation, it is critical that you understand the terms of your insurance policy.

You can install your unit yourself if you are confident in your abilities and have double-checked with your insurance company.

Step 1

Depending on the manufacturer, if their systems are not installed by certified professionals, the warranty may be voided.

Step 2

Make certain that you obtain all necessary state or local permissions before installing or upgrading a water heater.

Step 3

For water pressure more than 80 psi, you’ll need to install a pressure-reducing valve upstream of the new water heater before it will work properly. When establishing the cold and hot water connections (as described in the section below under “Establish the cold and hot water connections”), you should consider whether or not you need to install one.

Step 4

  • Make sure you check your local construction codes to see where you may put your water heater in your home. These tankless gas systems must be vented directly to the outdoors, rather than through a chimney, in order to function properly. Consequently, it is vital to identify a position where the unit may readily vent outdoors while also complying with local code requirements for vent placement. Carefully review the manufacturer’s installation instructions to ensure that you have adequate clearance around the device
  • Stay away from locations where:
  • Temperatures below freezing might have an impact on the unit. Any form of liquid might be sprayed on the device on a regular basis. There is a significant amount of humidity and wetness

Step 5

Make careful to accurately measure the space where you intend to install the water heater to ensure that you acquire the appropriate-sized unit.

Step 6

  • Tankless gas water heaters consume more gas than traditional tank-style water heaters. Determine whether or not your present gas line will be sufficient initially
  • If not, upgrade it. A professional contractor will be required to install a newer, larger gas pipe if your present gas line is unable to keep up with the demand.

Step 7

  • If there isn’t a shut-off valve before the heater, cut off the main water supply
  • Otherwise, turn off the heater. Remove the heater from service by closing all power and gas supply valves to it. Disconnect the unit’s power
  • When dealing with hot water, utilize a hose that is designed to tolerate high temperatures. To relieve pressure in the system, open a hot water faucet for a few minutes. Allow it to completely drain
  • Ensure that the water heater is disconnected from the gas and water pipes. Make sure to properly dispose of your old water heater.
  • For information on how to properly dispose of it, contact your local recycling and/or sanitation agencies.

Step 8

  • Ensure that the device is properly supported by constructing a mounting box that is approximately four inches away from the wall. The foundation wall should be properly secured with appropriate anchors. Follow the manufacturer’s instructions for mounting the device to the box firmly.

Step 9

  • Hiring a professional contractor should be your first choice unless you have extensive knowledge with gas line installations. Utilize a threaded black iron pipe to connect the existing tee to the unit position if your present gas line is the suitable size and you can connect it without breaking the existing connection. Remember to switch off the main gas line before removing the down pipe from the previous unit if you’re replacing it. After ensuring that the gas line is routed to the right location, you should install a tee, a sediment trap, and a gas shut-off valve. The shutdown valve and sediment trap should be connected to the heater in accordance with the manufacturer’s instructions. Install a new gas supply line from the tee to a location where it can be conveniently connected to the gas line of the new unit. You may utilize a black pipe or a flexible gas supply line to accomplish this task. Assemble the connections in the direction of the heater, starting with the tee, using two wrenches. Whenever possible, use thread sealant developed for gas lines when connecting gas pipe assemblies. After you have completed all of the gas line connections, you should test the line. Before turning on the gas, check the pressure with a pressure gauge.

Step 10

  • Connecting the water heater valves to the water supply line should be done according to the manufacturer’s instructions.
  • Connecting new hot and cold water lines to existing water lines should be done with copper pipe. Continue to connect the wires to the new unit. It is possible that copper pipe will need to be cut and soldered to the unit.
  • Connecting new hot and cold water lines to existing water lines should be done with copper pipe
  • Carry the lines to the new unit until they are complete. Depending on the unit, copper piping may need to be cut and soldered in place.

Step 11

  • The use of copper pipe is recommended for the connection of new hot and cold water lines to existing water lines. Continue to run the cables to the new unit. It is possible that you may need to cut and solder copper pipe to the device.

Step 12

  • When it comes to correctly venting the device, follow the manufacturer’s recommendations as a reference. There’s a considerable probability that you’ll be able to vent your water heater straight through the rim joists in your home. Only utilize pipes that have been specifically designed for this sort of venting. In some cases, depending on the manufacturer, you may require a vent kit. Make sure that the vent shaft of the new unit is sealed with a heat-resistant silicone sealant. Afterwards, attach a connection to it and secure it with an appropriate hose clamp
  • Place a length of stainless steel vent pipe on top of the structure. Put on a retaining ring to keep it in place. Folding over the tabs can help to keep it secure. Slip an elbow inside a pocket. Make sure that the aperture faces the direction in which the unit will vent to the outside
  • Select a spot on the joist or wall that will serve as the center of the vent hole for the purpose of venting outdoors. Drill a hole from the inside of the building at the location you’ve picked. Make a circle on the outer wall with a vent thimble and tape it in place. A spade bit should be used to bore a 1-inch hole at the center of the circular. Remove siding and shingles from around the vent hole in order to allow the flange thimble to be flat against the outside wall
  • Caulk around the edge of the flange with silicone caulk to seal the edge of the flange to the outside wall. Then, place the flange into the vent hole that has been created. Use screws to securely fasten it to the outer wall and silicone to seal the screws in place. Installing the internal flange should be done from the inside. A portion of vent pipe should be routed through the flange aperture. Tabs should be used to secure each part. Attach a short portion of vent pipe to the outside of the house and then connect the vent hood
  • Put the shingles and siding back on the house that you removed previously.
See also:  How To Install Water Filter Faucet

Step 13

  • To remove air from the water pipes and heater, turn on the faucet to its full “hot” setting. Close the water supply valve

Step 14

Connect the water heater to the wall outlet. That is all there is to it.

Step 15

The hot water line that originates from the water heater should be insulated.

Step 16

The gas should be turned on when the installation is complete. Your water heater should be up and running at this point!

How to Install an Electric Tankless Water Heater

Installation and replacement of tankless water heaters may be quite expensive, as we realize. Installing your own unit is doable, but we recommend that you proceed with caution. This should only be attempted if you have extensive experience working with water lines and electrical systems. Installing your tankless water heater incorrectly might result in significant harm to your home. If you are considering a do-it-yourself installation, it is critical that you understand the terms of your insurance policy.

You can install your unit yourself if you are confident in your abilities and have double-checked with your insurance company. The instructions below will guide you through the process.

Step 1

Depending on the manufacturer, if their systems are not installed by certified professionals, the warranty may be voided.

Step 2

Confirm that your electrical service panel has the capacity to manage the energy demands of an electric tankless water heater before installing one. It’s possible that you’ll need to upgrade your panel or install a whole new one. It is possible to uncover useful information by inspecting your electrical breaker box or the label on the electrical panel in your home. You might also consult with an electrician. The majority of suitable water heaters require a minimum of four 40AMP breakers to deliver hot water for a two and a half bath house.

Step 3

For water pressure more than 80 psi, you’ll need to install a pressure-reducing valve upstream of the new water heater before it will work properly. When establishing the cold and hot water connections (as described in the section below under “Establish the cold and hot water connections”), you should consider whether or not you need to install one.

Step 4

It is necessary to install a pressure reduction valve upstream of the new water heater when the water pressure is more than 80 psi. When establishing the cold and hot water connections (as described in the section below titled “Establish the cold and hot water connections”), you should consider whether you need to install one.

Step 5

  • In order to heat water for the entire house, it is best to locate the unit closest to the area in which the majority of the hot water is consumed. If you’re installing a point-of-use system, try to locate them as near to the points of use as feasible. Always keep in mind that most electric tankless water heaters must be mounted vertically, with the water and electrical supply connections on the bottom of the unit. Follow the manufacturer’s recommendations for leaving a particular amount of clearance for service
  • In general, you want to stay away from locations where:
  • In order to heat water for the entire house, it is best to locate the unit closest to the area in which the majority of the hot water is consumed
  • Put these as close as feasible to the points of use if you’re using a point-of-use system
  • And Always keep in mind that most electric tankless water heaters must be mounted vertically, with the water and power supply connections on the bottom of the unit. Maintain at least a specified minimum clearance for service, as specified by the manufacturer. In general, you want to stay away from locations where you could encounter:

Step 6

Disconnect any circuit breakers that are connected to the new device. This is critically crucial!

Step 7

You don’t want your office to become a swamp!

Step 8

  • If there isn’t a shut-off valve before the heater, cut off the main water supply
  • Otherwise, turn off the heater. Remove the heater from service by closing all power and gas supply valves to it. Disconnect the unit’s power
  • When dealing with hot water, utilize a hose that is designed to tolerate high temperatures. To relieve pressure in the system, open a hot water faucet for a few minutes. Allow it to completely drain
  • Ensure that the water heater is disconnected from the gas and water pipes. Make sure to properly dispose of your old water heater.
  • For information on how to properly dispose of it, contact your local recycling and/or sanitation agencies.

Step 9

  • Remove any screws that are holding the front cover of the new device in place
  • And Please keep in mind that you may need to remove at least one plug before you can set it aside.

Step 10

A set of adequate anchors and screws should be included in the box.

Step 11

  • Connections for the cold and hot water should be made. The right side of the body is commonly affected by a cold.
  • The quickest and most straightforward method is to use stainless steel flex pipe with Teflon tape. You can also utilize copper tubing that has been rated for use in high-temperature environments. If you have to cut into a pipe, make sure the edges are clean. Before connecting the pipes to the water heater, flush them with water once they have been soldered. Also keep in mind that too much heat might cause harm to the water heater. If you want to do maintenance on your heater, it’s a good idea to install a shut-off valve before and after it. This will allow you to stop off the water supply to the unit without shutting off the water supply to the rest of your home
  • If you need to install a pressure reduction valve, you should do it immediately on the cold water side of the plumbing system. The installation of a temperature and pressure relief valve is unlikely to be necessary (T P). However, you should double-check your local and state installation rules to see whether or not you require a permit.

Step 12

  • In this case, stainless steel flex pipe with Teflon tape is the quickest and most straightforward solution. It’s also possible to utilize copper tubing that has been rated for high-temperature usage. Make sure to tidy up the edges of the pipe if you have to cut into one. Prior to attaching the water heater to the soldered pipes, clean them out with water. It’s also important to realize that too much heat might be detrimental to your water heater. If you want to do maintenance on your heater, it’s a good idea to install a shut-off valve before and after it. This will allow you to switch off the water supply to the unit without also turning off the water supply to the rest of your home
  • If you need to install a pressure reduction valve, you should do it now on the cold water side of the plumbing system
  • Temperature and pressure relief valves are not likely to be required in your situation (T P). It’s best to double-check your local and state installation codes, though, to make sure you don’t require one.

Step 13

This step must not be skipped!

Step 14

  • Heater on one side, and electrical panel on the other, is the recommended arrangement
  • Comply with the manufacturer’s wiring diagram and their instructions for selecting the appropriate wire, circuit breaker number, and circuit breaker size
  • And Cutting and stripping every wire set to the proper length is followed by pushing them through the bottom holes of the new water heater’s housing. After that, connect the wires to the appropriate slots on the terminal block.
  • For the most appropriate torque, see the product handbook. It is important to remember that a ground conductor must be connected to the circuit breaker panel and the grounding busbar of the unit for each circuit.
  • Double-check that all of the electrical connections are in proper working order and that all of the wire sets have been appropriately installed.

Step 15

Make use of the screws that you already removed.

Step 16

Make use of the screws that were previously removed.

Step 17

You can reinstall the screws that you removed before.

Learn More About Tankless Water Heaters

Right now, our plumbing professionals are here to take care of your repair needs. They’ll assess your situation, propose a solution at a reasonable fee up front, and then get to work!

Upfront Pricing

There are no hidden fees.

Quality Work

Guaranteed 100 percent customer satisfaction

24/7 Service

Guaranteed complete customer satisfaction

How to Install a Tankless Electric Water Heater: A 10-Step Guide

An Overview of the Process of Installing or Replacing an Electric Water Heater

  • Step 1: Turn off the circuit breaker and shut off the water supply. Step 2: Turn off the water heater. Step 3: Take off the front cover. Step 4: Install the water heater. Step 5: Join the pipes together. Install the flow and pressure valves in the next step. Burning the hot water system is step 7. In Step 8, you will inspect the electrical components. Activate the circuit breaker (Step 9)
  • Tenth step: check the temperature and outlets

Some problems with water heaters can be repaired. For those who have an old or outdated water heater, it may be necessary to replace it. Although it is possible for a water heater to survive for up to 20 years, the majority of them only last 10 years. If you plan to install a tankless electric water heater yourself, it’s critical that you understand what you’re getting yourself into before you begin. This Might Also Be of Interest to You: Installing or replacing a gas water heater is a simple process.

If you arrive at a job site without the proper tools or a clear grasp of the tasks at hand, it’s likely that you’ll run into problems that will cost you both time and money. This tankless electric water heater installation guide will walk you through every step of the process from beginning to end.

1. Switch Off Circuit Breaker and Water Supply

Immediately before to beginning the job, it is critical that the circuit breaker be turned off in order to guarantee that the electric wires are not powered on while you are working. At this time, you should also switch off the water supply to your home unless you want to risk flooding your home while attempting to replace your present water heater with a new one. Always keep in mind that flooding may cost tens of thousands of dollars in damage, which is why doing the first item on this list is the most critical.

See also:  What Temperature Should Your Hot Water Heater Be Set At

2. Drain Your Old Heater Before Disconnecting It

The tank-type water heater that is now installed in your home will need to be drained prior to being removed from the structure. This will necessitate the use of a hose and a container, such as a bucket. Check out our how-to guide on how to drain a water heater for more thorough information. The old wiring and wall-mounting brackets will need to be removed first, and then the connecting pipes will need to be unscrewed. Be careful not to do any harm to the old wiring or pipes while performing this procedure.

3. Remove the Front Cover

The front cover of the new tankless unit should be carefully removed with a screwdriver before the unit can be installed. Once all of the screws have been removed, store them in a safe location where they will not be misplaced. It is vital to use all of these screws in order for your water heater to perform correctly. Take into consideration the possibility that wires will be connected between the cover and the device. Carefully unplug the cables before removing the lid completely.

4. Mount the Water Heater

Following that, the device will need to be attached to a wall. Make certain that the water heater is not installed in a cluttered or disorganized location of your house or business. Having said that, it’s critical that you have quick access to the unit in the case of an accident or other emergency. Mounting the water heater is straightforward and may be accomplished using a combination of screws and the mount that comes with the unit. Follow the installation instructions that came with your item.

5. Connect Any Pipes

Upon completion of the installation, you will need to connect the pipes that will deliver hot water throughout your home. These are the connectors that will be used to bring water into and out of your water heater. They should be positioned at the bottom of the unit, if possible. When you receive your device, it is possible that you may be given an installation diagram, which you should look to in order to establish where the connections should be made. Stainless steel is the ideal sort of pipe material for a tankless water heater since it is corrosion resistant.

Copper and PVC piping are suitable alternatives to stainless steel piping if you do not have access to stainless steel pipes.

Many instruction manuals recommend that you clean your equipment on a regular basis. Additional Related Articles:

  • How Much Does It Cost to Repair or Replace Your Water Heater
  • How Much Does It Cost to Install a Water Heater
  • How to Check the Element in a Water Heater
  • Don’t Forget to Flush Your Toilet! The following is a 6-Step Guide for Flushing Your Gas or Electric Water Heater: How Do I Turn On My Water Heater
  • I’m Sick of Cold Water? Instructions for Increasing The Temperature of Your Water Heater

6. Install Flow and Pressure Valves

As soon as all of the connections have been completed, it’s time to install the flow and pressure control valves. Flow valves are straightforward to install. In the event that repairs are required, you may simply cut off the water supply to the heater rather than having to shut off water throughout the rest of your property. Pressure valves are only required if and when the local plumbing authority specifies that they are needed. The pressure release valve should be put on the side of the electric water heater that is closest to the “hot water.” To ensure optimum safety, you might also install one on the other side of the heater from the heater.

7. Bleed the Hot Water System

The flow and pressure valves must be installed once the connections have been completed. Valve installation is a breeze with a flow valve. In the event that repairs are required, you may simply cut off the water supply to the heater rather than having to shut off water throughout the rest of your house. It is only necessary to install pressure valves if the local plumbing authority mandates that they be done so. Installation of the pressure release valve on the “hot water” side of a tankless water heater is strongly recommended.

8. Inspect Electrical Connections Before Attaching Cover

It is critical that you take the time to verify the electrical connections to your water heater in order to protect your own safety as well as the safety of everyone else in your family. Check to see that the connections are correctly connected and that the terminals have been placed in the proper locations. After that, the cover should be reattached using all of the screws that were previously used. The installation process is practically complete once the unit’s cover has been properly put on top of the device.

9. Switch Circuit Breaker On

It is safe to turn on the circuit breaker now that you are no longer need to perform any maintenance on the heater directly.

10. Check Temperature and Test Outlets

Once the water heater has been switched on, you’ll want to adjust the temperature settings on the system. Because these units may get extremely hot when used at their maximum settings, it is suggested that you avoid using them in order to reduce the possibility of burns. This is also a good time to check every hot water outlet in your home, including taps, showers, dishwashers, and laundry washers, to ensure that the temperature is proper and that the water warms up quickly. Turning down the temperature settings may be necessary if the water is becoming too hot to handle.

DIY Tankless Water Heater Installation Is Dangerous

However, just because there are safety procedures in place to prevent hot water tanks from exploding does not imply that they are impenetrable to failure. When unlicensed individuals install hot water tanks, the possibility of something like this occurring increases, and the likelihood that they will not have the necessary insurance to pay the damage if it does occur increases.

Water heaters, in particular, those run on gas are extremely combustible. An explosion or a fire might occur if one of the installation’s components is mishandled.

Carbon Monoxide Leaks

They are undetectable by the human senses, which is why they are referred to as a silent killer. A competent plumber can help you avoid carbon monoxide poisoning by ensuring that your system is properly vented before the problem occurs. Nonetheless, a CO detector should always be installed. This procedure is crucial for in-home safety, but it is frequently performed incorrectly by inexperienced repairmen. Whatever number of ancient systems your uncle installed years ago, please do not make the fatal error of attempting to install your own water tank on your own dime.

In many cases, amateur installation is not covered by your guarantee.

The majority of internet sales and purchases are canceled right away.

Without proper installation, the hot water heater may be damaged or even destroyed, and why should the manufacturer be responsible for such a thing?

DIY Can Hurt Your Property Value

Sure, you might be able to do a plumbing task on your own and save some money, but is your handy work up to code? Did you get a permit to do this? When it comes time to sell your property, such blunders might end up costing you a lot of money in the long run.

Tankless Water Heater Installation

Although you might be able to do a plumbing task on your own and save some money in the process, is your handy work up to code? Is it true that you obtained a permit? These blunders might end up costing you a lot of money down the line when it comes time to sell your house.

EfficiencySavings of Tankless Water Heaters

In addition to being one of the most energy-efficient water heaters available, a gas tankless water heater utilizes just the energy required to heat the water when it is needed. This product is an excellent energy-efficient solution for your house, especially in light of rising energy expenses and increased environmental consciousness among the general public. There are several advantages to purchasing a gas tankless water heater, including the following:

  • Water heaters that use less energy
  • Water that is always hot
  • Tankless systems are simple to operate and have a longer life expectancy (the typical tankless system lasts 20 years). There is no tank to leak
  • It conserves space
  • Temperature control that is precise
  • System that can diagnose itself

What Size Tankless Water Heater Do You Need?

Tankless water heaters operate in a different manner than typical water heaters, according to the majority of experienced plumbers. Despite the fact that they are available in a variety of sizes, the size of tankless water heaters is determined by the number of gallons of hot water they can supply every minute rather than the number of total gallons of water they can hold. Heaters that use the traditional method heat and store hot water in a tank until it is needed. Tankless water heaters only heat water when it is actually required to do so.

Thinking of upgrading to a tankless water heater? Before doing so, learn the pros and cons of installing one

Are you considering making the switch to a tankless water heater? Before doing so, educate yourself about the advantages and disadvantages of installing one, including the cost, needs, and upkeep. It is possible that you are considering installing a tankless water heater in your house if it is time to replace your current water heater. We’ll explain how tankless water heaters function and point out some of its pros and downsides to assist you in making the best decision about which kind to install.

Do you require an expert right away?

With American Home Shield ProConnect, you can hire a certified, local home repair professional in just a few clicks. To make a reservation, please click here. *This product is available in the majority of major markets. The services available differ depending on the market.

How Tankless Water Heaters Work

Known variously as demand type, on-demand, or instantaneous water heaters, these appliances heat water directly, eliminating the need to store water. A flow detecting device is installed in a tankless heater, and it is triggered anytime the hot water tap is opened. A gas burner or an electric element is used to heat the water, which is then sent to the various locations in your home where it is needed. You won’t have to worry about running out of hot water because there isn’t a tank that has to be filled.

Advantages Of Tankless Water Heaters

  • They are more compact than typical storage heaters, are wall-mounted, and do not take up any floor space when not in use. As a result of their size, they can be particularly appealing in houses where space is limited
  • They can also help you save money on your energy bills. According to the United States Department of Energy, heating water accounts for around 30% of a family’s total energy use. It is possible to save up to 50% on these expenditures by installing a tankless water heater, resulting in an average yearly savings of $80. Tankless water heaters are also more durable and less likely to malfunction, resulting in potentially disastrous flooding in your house. Compared to traditional water heaters, tankless systems have a lifespan that is about twice as long – 20 years or more.

Disadvantages Of Tankless Water Heaters

  • Tankless units are more costly than conventional units. It will cost around the same as a standard tank type to purchase an electric tankless heater, however a gas tankless heater would cost between $1,000 to $1,200. The national average for tankless unit installation is somewhat more than $1,700, which is in addition to the original cost of the unit. A safe vent must be created for a gas unit to prevent carbon monoxide from collecting within the property in many circumstances. Existing plumbing must also be expanded or moved in many cases. Tankless water heaters do not provide “instant hot water,” even when energy savings are taken into consideration
  • For many households, it will take around 20 years to completely return their expenditures. It is not always the case that a tankless water heater delivers hot water to your faucet any faster than a traditional water heater, contrary to common belief. In fact, a tankless device may be more time consuming. It takes some time for the tankless unit’s heating element to warm up the water before it can be delivered to the faucet
  • The amount of hot water that can be delivered is limited by the unit’s ability to heat the water. It is typical for tankless water heaters to provide 2-5 gallon-per-minute flows of hot water, which may not be sufficient for several simultaneous uses of hot water in your home. For example, having a shower and running the dishwasher at the same time may cause a tankless water heater to reach its maximum capacity and fail. Comparing tankless versions, especially if you live in a multi-person home, is important. Pay close attention to the gallons per minute (GPM) flow rate of each type. The bigger the number of users and the greater the number of simultaneous usage options, the higher the GPM requirement. In order to satisfy the needs of a big home, one alternative is to install many tankless units
  • However, this can become quite costly over time. It is possible that tankless water heaters will not provide hot water during a power outage. Tankless water heaters, in contrast to traditional water heaters, do not provide a backup hot water supply in emergency scenarios
  • Tankless systems are also subject to failure owing to hard water. Hard water is a concern for all water heaters, but it is particularly challenging for tankless water heaters. They should be completely emptied and their filters updated on a monthly basis. They also require frequent flushing to function properly. (Tank units only need to be flushed once or twice a year, at most.) If you don’t take the necessary precautions, hard water can completely ruin a tankless water heater in as little as two years. In addition, failing to adhere to these maintenance requirements may result in the voiding of the manufacturer’s guarantee
  • Tankless devices are hard to maintain. Investigate the interior workings of a common tankless water heater or air conditioner. As a result of all the complex technologies tankless water heaters rely on, it is easy to understand how much may possibly go wrong.
See also:  How Big Water Heater Do I Need

Gas or Electric

Electric tankless water heaters are significantly less expensive than their gas counterparts. Installation is less complicated and less expensive, and they are often less difficult to maintain than gas-powered ones. Only a few handful, however, have the capability of serving many locations at the same time. Gas units are available in a wide range of types and sizes for both residential and commercial applications, with outputs ranging from 130,000 to 380,000 BTUs in certain cases. More BTUs equate to more heating capacity.

  • As a result, your home’s gas pipe, meter, and main line to the meter may not be correctly proportioned, necessitating a costly reconfiguration and installation of new equipment.
  • The total energy efficiency of a tankless water heater is assessed using an energy factor (EF) rating, which is available for both gas and electric types.
  • Tankless water heater energy factors now range between.64 and.91 for gas-fired devices, and up to.99 for electric versions, depending on the manufacturer.
  • For a home of one or two persons, a tankless electric unit will most likely be more than sufficient.

Water Heater Protection

Water heaters that are powered by electricity are less expensive than those powered by natural gas. Installation is less complicated and less expensive, and they are often not as difficult to maintain as gas-powered versions are. But only a select handful are capable of serving many locations at the same time. Gas units are available in a wide range of types and sizes for both residential and commercial applications, with outputs ranging from 130,000 to 380,000 BTUs in size. Increasing the BTU output results in increased heating power.

It is possible that the plumbing, meter, and main line to the meter in your home are not appropriately proportioned, and that a costly reconfiguration and installation will be required.

EF ratings are used to determine the overall energy efficiency of tankless water heaters, which is applicable to both gas and electric types.

Department of Energy were used to get this EF ranking.

When it comes to water heater efficiency, a greater energy factor indicates a more efficient unit. A tankless electric unit will most likely be sufficient for a family of one or two persons. A gas-fired tankless water heater is most likely the best option for bigger families.

Tampa Tankless Water Heater Installation

Are you in the market for a new hot water heater? Is your present one no longer functioning properly? You might want to think about investing in a tankless water heater. It may be aggravating to be without hot water when you need it, especially when the weather turns chilly in Florida during the winter. Is it important to you to have a more energy-efficient device that will save you money in the long run? It is possible that you will wish to consider installing a tankless water heater. Providing high-quality, competent, and cheap tankless water heater installation services, Home Service Heroes is the company to call.

Instead, look for our company’s name on the internet.

What Is a Tankless Water Heater?

A tankless water heater is a more energy-efficient alternative to the typical tank-style water heater. When compared to traditional tank water heaters, tankless water heaters are more energy and cost efficient devices. What’s the difference between a tankless water heater and a typical water heating system? It is rather self-explanatory based on the name. A tankless water heater is a system that does not require the use of a tank to store water, as opposed to a traditional tank water heater. Tankless water heaters heat water on demand rather than conserving it for later use, resulting in hot water that appears to be available instantly.

Tankless water heaters are around the size of a suitcase in terms of size.

The Tankless Water Heater Installation Process

A tankless water heater is a more energy-efficient alternative to the typical tank-style water heater. When compared to a traditional water heater, tankless water heaters are both more energy and cost efficient. What’s the difference between a tankless water heater and a regular water heater, exactly? It’s very evident from the name. It is important to note that, unlike tank water heaters, tankless water heaters do not require the use of a tank to store water. Tankless water heaters heat water on demand rather than conserving it for later use, resulting in hot water that seems to be available immediately.

It takes up less space than a suitcase to house a tankless water heater.

Is a Tankless Water Heater Right For You?

A tankless water heater is a more energy-efficient alternative to the typical tank-type water heater. When compared to a traditional water heater, tankless water heaters are more energy and cost efficient devices. Why should you choose a tankless water heater over a regular model? It’s quite self-explanatory based on the name. A tankless water heater is a system that does not require the use of a tank to hold water, although a traditional tank water heater does require this usage. Tankless water heaters do not store water for subsequent use; instead, they heat water on demand, providing seemingly instantaneous hot water.

Because the tankless variant does not require the installation of a big storage tank, technicians may install it almost anyplace. Tankless water heaters are around the size of a briefcase in terms of size. They may be mounted on the wall or under the sink.

Benefits of Installing a Tankless Water Heater

The following are the primary advantages of installing a tankless water heater: Consider the following factors to evaluate if a tankless water heater is the best option for you.

Hot Water on Demand

You appear to have hot water on demand at all times due to the fact that water is delivered through the pipes and heated only when needed.

Reduced Utility Bills

Traditional water heaters maintain the temperature of the water even while it is not being used. This strategy will raise your energy usage, which will result in you spending more money every month as a result.

Use Home Service Heroes For Your Tankless Water Heater Installation

Whether you’d like to learn more about tankless water heaters or would want to schedule an installation, give us a call today!

Tankless Water Heater Installation

I really want to.

ServiceOverview

  • It’s something I really desire.

Want free repairs and maintenance for life?

With Comfort as a Service, you only pay for what you use. Get a new, energy-efficient tankless water heater for as little as $44.99 a month, with lifetime repairs and maintenance included.

Cost of a tankless water heater installation in Atlanta

  • There are several system configurations available. Tankless water heater that is new and high-efficiency
  • Manufacturer’s warranty of ten years
  • Financing options that are flexible.

How a Rinnai Tankless Water Heater Works

  • Options for several systems are available. Tankless water heater that is new and high-efficiency. Manufacturer’s warranty of ten years
  • Financing options that are customizable.

Hot Water Wisdom- Tank vs. Tankless

  • Increased efficiency (resulting in cheaper energy expenses)
  • There is never enough hot water (a tank will eventually run dry)
  • Tanks take up a lot of space, so make more room. Longer lifespans (20 years or more as opposed to 10-15 years)

How YourTankless Water Heater Installation Works

Make a time for your appointment. To arrange an appointment, please contact us online or phone us at (770) 594-9969 (toll free). We’ll contact you to confirm your appointment time. A confirmation email with a photo of your tech will be sent to you, so you’ll know who to look out for when you come in for your appointment. 2

Installation

Install your water heater as soon as possible. The plumber will come to your house to assess your hot water requirements (for free). Your household will be provided with a tankless water heater that will never run out of hot water. After that, you’ll be presented with a number of system alternatives, each with a simple price structure. On the day of the installation, our crew will do the following tasks:

  1. Wear shoe coverings and set down drop cloths to protect your home from damage during the storm. Installing your new tankless water heater is straightforward. Leave your home in excellent condition. (If we get it dirty, we’ll get it clean.)

Feedback

Please let us know how we did. When we claim “100 percent customer satisfaction guarantee,” we mean it. Are you dissatisfied with our service? Just let us know in our follow-up survey if this is the case. We’ll make it right as soon as we can.

Gas vs electric tankless water heaters

You’ll need to consider a variety of things, including the following:

  • Utilities are readily available at your residence. If you don’t have access to a natural gas line, you’ll most likely have to settle with an electrical unit. It is common for the added expense of installing a gas line and exhaust vent for a gas unit to be quite costly. Although an electric tankless water heater is an option, you’ll want to be sure your home’s electrical system can manage the additional load before making the purchase. If it can’t, you’ll need to update your panel, which will depend on the size of your household and how much water you use. In general, gas tankless water heaters may heat your water more quickly than electric tankless water heaters. If you live in a one-person household, an electric unit will most likely be sufficient for your needs. For those who have a big family, a gas unit’s rapid heating capabilities will certainly be required
  • Groundwater temperature is another factor to consider. Groundwater temperatures in warmer areas, such as Atlanta, are greater than those in colder ones. As a result, your water heater will not have to work as hard to heat the water in your home, and an electrical water heater will most likely be sufficient for most Atlanta homes. Those with bigger houses, however, may want to consider the heating capability of a gas unit, since temperatures may dip rather low in the winter. Operating expenses are another consideration. Generally speaking, electric tankless water heaters are more expensive to operate than gas models. This is due to the fact that power charges are significantly higher than gas rates.

Leave a Reply

Your email address will not be published.