Where Is The Water Filter On My Samsung Refrigerator

Replace the water filter in your Samsung refrigerator

There are three different types of Samsung water filters, so you’ll want to be sure you’re getting the right one for your refrigerator before purchasing one. Replacement filters are available for purchase on ouraccessories page if needed. To begin, identify the filter in your refrigerator’s model. You should refer to your user handbook if you are unclear about the location. Then, on the filter itself, look for the model number printed on it. This will inform you of which of the following filter types you will require for your application.

If you’re not sure whether or not you need to replace the filter, look for an indication light on your refrigerator.

If you are about to replace the filter, the light will become purple to indicate that it is time.

You should alter the filter as soon as possible at this point.

  1. It is important to note that there are three different types of Samsung water filters, so be sure to select the suitable one for your refrigerator. Replacement filters are available for purchase on ouraccessories page if necessary. To begin, identify the location of the filter in your refrigerator model number. If you’re not sure where to look, see your user handbook. Then look on the filter itself for the model number. Which of the following filter types you will require will be determined by the results of this calculation. HAF-CINHAF-QINHAFCU1 It should just take a few minutes to replace your water filter, and it is simple to do. You may check the indication light on your refrigerator if you’re not sure whether you need to replace the filter. It may be blue, yellow, or green depending on your refrigerator model when the filter is brand new, for instance. A purple glow indicates that it is about time to replace your filter. The signal will turn red after six months. You should replace the filter as soon as possible at this point. Filters with the HAF-CIN and HAF-QIN designations are as follows:

Types of HAFCU1 filters include:

  1. After turning off the water, identify the filter and clean it as needed. If you are unclear of where it is, please refer to your user handbook for assistance. Using a left-handed twist, you can remove the old filter. This will allow you to access it
  2. Afterwards, pull it downward to remove it from the filter housing. The replacement filter should be inserted by pushing it up into the filter housing and then turning it to the right. Check to ensure that the notch at the top of the filter corresponds to the arrow on the filter’s housing. Replace your filter and then flush it thoroughly with a few liters of water to wash out any contaminants or air that may have gotten into it. Then, make sure that the water filter light on your refrigerator is turned back on. Please refer to the following sections for further information.

After turning off the water, locate the filter and clean it as necessary. You should reference your user manual if you are unclear of where it is located. Using a left-hand twist, you may remove the old filter. Upon doing so, it will be unlocked. Afterwards, pull it down to release it from the filter housing. Using your fingers, press the new filter upwards and then to the right; this will ensure that it is properly installed. To avoid clogging the filter, make sure it has a notch at the top that matches the arrow on the housing.

Then, make sure that the water filter light on your refrigerator is turned off and back on again.

  1. If theFilter Resetbutton is accessible on the control panel, locate it and press it. In some cases, it is a secondary function of another button on the panel
  2. Once identified, press and hold the proper button for 3 seconds until the light turns out
  3. The filter symbol will either turn off or return to its usual color when the light is turned off. This restarts the timer for the next six months.

Please keep in mind that some models may require you to press two buttons at the same time in order to reset the light. Touch screen models will instead make use of on-screen menus. Consult your refrigerator’s owner’s handbook for detailed operating instructions. The water filter light and timer on your Family Hub refrigerator may be reset by following the instructions outlined below.

  1. Start by selecting Apps from the Home screen, followed by Fridge Manager
  2. Then choose Water Filter from the Home screen, followed by Reset and then Proceed. The filter light and timer will be reset as a result of this. If you require a Samsung water filter, you may purchase one by pressing the Buy Filter button after tapping the water filter symbol.

On models RF4289 and RSG309, you may also reset the filter light by pressing the reset button.

  1. Then, at the bottom of the screen, navigate to and pick theSettingsicon, and then tapWater Filter to begin. As soon as the Water Filter menu appears, press Next three times in the lower right corner of the screen until you reach page 4/4 of the Water Filter menu. Hold the object with your fingertips. Remove and reinstall the water filter until it changes its status, which may be done in the middle of the display. After the message “Filter Replaced” appears and disappears from the screen, tapSave in the lower right corner of the screen.

Then, at the bottom of the screen, navigate to and pick theSettingsicon, and then tapWater Filter. As soon as the Water Filter menu appears, hit Next three times in the lower right corner of the screen until you reach page 4/4 of the Water Filter menu. Hold the object with your fingertips Remove and reinstall the water filter until it changes its status, which should take around a minute or two. TapSave in the bottom right corner of the display when the message “Filter Replaced” shows and disappears.

  • Then, at the bottom of the screen, navigate to and choose theSettingsicon, and then tapWater Filter
  • When the Water Filter menu appears, press the Next button in the bottom right corner three times until you reach page 4/4 of the Water Filter menu. Hold the object with your finger. Keep resetting the water filter in the center of the display until the filter’s status changes
  • After the message “Filter Replaced” appears and disappears, tapSave in the lower right corner of the screen.

NSF/ANSI 53 is a standard that specifies how a product should be designed, manufactured, and tested.

  • Certified to decrease a pollutant that has a negative impact on health. The following substances have been identified as having negative health effects by the United States Environmental Protection Agency (EPA) and Health Canada: Asbestos, Atrazine, Benzene, 2, 4-D, Carbofuran, Chlorbenzene, Cyst (99.99 percent), Endrin, Ethylbenzene, Lead, Lindane, Mercury, O-Dichlorobenzene, P-Dichlorobenzene, Tetrachloroethylene, Toxaphene

NSF/ANSI 401 is a standard for food safety and sanitation.

  • It has been proven to lower one or more of the 15 emerging pollutants in drinking water by at least 50%. Pharmaceuticals and chemicals that are not yet controlled by the Environmental Protection Agency or Health Canada include: atenolol, bisphenol A, carbamazepine, DEET, estrone, linduron, nonylphenol, phenytoin, trimethoprim, and trimethoprim sodium.

Check out our troubleshooting guide for assistance if you are having difficulties installing the water filter in your refrigerator.

How to Change the Water Filter on a Samsung Refrigerator

You’ve been ignoring the Change Water Filter Indicator on your Samsung refrigerator for a little bit longer than you should have. If this is the case, don’t waste any more time! Follow these simple step-by-step directions to learn how to replace the water filter in your Samsung refrigerator. It is critical to change your Samsung water filter on a regular basis for the health of your family and your refrigerator! A clean water filter installed in your Samsung french door, four flex, or side-by-side refrigerator may make a significant impact in the quality of your drinking water and food preparation.

Step-by-Step: How to Change the Water Filter on a Samsung Refrigerator

If you don’t have technical skills, changing your water filter is a breeze thanks to a Samsung design. You can begin by following the steps outlined in this document.

Step 1: Purchase the Correct Samsung Water Filter

We strongly advise you to get the Samsung Factory Water Filter. If at all possible, stay away from knock-off brands. Although they are less expensive, the quality is not similar. The Samsung Factory Water Filter may be purchased online through Amazon, with most items shipping the same day on conventional Prime or free 2-hour delivery on Prime Now, depending on the product. We encourage that you sign up for the Amazon Subscribe and Save program in order to save money on future purchases. To ensure that you never have an out-of-date water filter again, schedule your water filter to be delivered automatically every five months.

Step 2: Verify you have the right part!

Refrigerator water filters are model number specific, which means that you must use the exact filter for your refrigerator and not just any water filter. WARNING: Before opening the package, double-check that you have the appropriate filter. It is not possible to return the water filter once it has been installed. The water filter component number DA29-00020B (shown below) is used in the majority of Samsung french door, four flex, and side-by-side refrigerators; nevertheless, it is important to check the refrigerator model number to ensure that you are purchasing the proper filter for your product.

See the following specifications for further information: Your Samsung water filter will be sent with a new water filter, an instruction manual, and sticker reminders for the filter’s expiration date.

Step 3: Locate the Samsung Water Filter on Your Refrigerator.

The position of the water filter is determined by the setup of your Samsung refrigerator. French DoorsFour Flex models have a water filter that is situated between the produce drawers and the French DoorsFour Flex models’ fresh food area (as pictured below).

Samsung side-by-side refrigerators are equipped with a water filter, which is positioned on the fresh food side of the bottom drawer on the right-hand side of the unit.

Step 4: Prepare the Filter for Installation

Simple removal of the plastic wrapping and removal of the top cap are all that is required to ready the filter for installation. A well designed filter will look something like this.

Step 5: Install the Samsung Water Filter

Installing the water filter is accomplished by turning the filter knob to the left. It takes approximately 1/4 turn to unlock the filter. If possible, you should be able to remove the filter without having to switch off the water supply. To release the filter, slowly move the refrigerator forward and switch off the main water supply. In order to install the replacement filter, screw it into place with a quarter-clockwise turn. When the filter is locked in place, you may hear a pressure noise, which is completely normal.

Step 6: Purge 1 Gallon of Water

1 gallon of water should be sent through the filter. For the first 3-5 seconds, you may hear some air in the lines. This is quite normal. Remove the water from the container. It’s now time to put your water dispenser to work!

Step 7: Reset the Change Water Filter Indicator

By pressing and holding the Crushed Ice button for three seconds, you may reset the Change Water Filter Indicator light. Do you need assistance with the water dispenser or ice maker on your Samsung refrigerator? For Samsung Certified Care on your refrigerator, get in touch with Unique Repair Services.

Samsung Fridge Filters: Easy-Guide to Replacing, Resetting and Changing.

Samsung is one of the most successful corporations in the world today. The South Korean technology corporation, which has its headquarters in Seoul’s Samsung Town, was initially started as a trade company, but it entered the electronics sector in the 1970s after expanding into other markets. Samsung declared in 2015 that it intended to surpass General Electric as the world’s largest appliance manufacturer. To achieve this, as you might expect, the company had to outperform numerous well-known global corporations, like Whirlpool, Bosch, and Electrolux, among others.

  1. Samsung’s collection of home appliances will feature refrigerators that supplied sparkling as well as still, filtered drinking water, making them far more sophisticated than anything else that other household manufacturers were manufacturing at the time.
  2. Samsung is unquestionably one of the world’s biggest appliance manufacturers, despite the fact that they are not exactly at the top of the scoreboard that has just been established.
  3. One of the reasons water tastes so much better when it comes out of a Samsung refrigerator is due to the superior filtering system that the refrigerator has installed.
  4. It is critical that you update your Samsung water filter on a regular basis if you want to continue drinking wonderful water at home.
  5. This will result in terrible tasting drinks that you will be embarrassed to give your friends and family.

We’ve put together a simple tutorial on everything you need to know about replacing your Samsung fridge filter at home so that you can continue to be proud of your great beers, clean water, and crystal-clear ice.

1. How to replace RSG5UCRS Samsung Fridge Filter:

When it comes to replacing your RSG5UCRS Samsung Fridge Filter, we have some good news for you: it’s more simpler than you would imagine. When the filter indicator light becomes orange or pink, it indicates that a new filter should be purchased. When the filter indicator becomes red, it is time to replace it. If six months have passed and the indication light has not gone red, we nonetheless recommend that you replace the filter in order to preserve the excellent quality of your drinking water at all times.

See also:  What Is The Normal Temperature Setting For A Hot Water Heater

Only internal filters should be replaced according to the procedures provided below.

  1. The old water filter may be removed by turning it 45 degrees to the left to open it
  2. At this point, gently remove the old water filter and toss it away
  3. The water will stop off automatically at this time. Insert the new water filter into the available area and rotate it 45 degrees to the right
  4. If the padlock symbol on the filter corresponds to the sign on the filter, the filter is in the proper position. Immediately following the installation of the new filter, push the water filter reset button for three seconds to reset the light indicator.

Suggestions for improvement In the event that you are having difficulty removing the water filter, it is possible that there is excessive water pressure behind the filter. Remove the top two refrigerator shelves and use a stronger pull on the filter to get it out. If you are unable to squeeze the new filter into the available area, turn off the water supply valve and dispense a little amount of water. As a result, the pressure will be reduced, making it easier to install the new filter. All of the steps that follow are for external filters only.

Instructions on how to change an internal filter may be found further up the page.

  1. Immediately turn off the water supply
  2. Remove the old cartridge from the system and dispose of it properly
  3. The water filter should be positioned such that it flows in the direction of the refrigerator
  4. The inlet and exit tubing should be connected to the proper end of the filter by firmly inserting the tube all the way into the filter until it is snugly shut
  5. Check to see that the tube is square and free of scratches – you may trim it if required. The filter clip should be installed according to the directions in the installation manual. Make sure there are no leaks in the filter by turning on the water. Re-do the installation processes and check again whether there are any leaks. If the leaks continue, remove the filter and contact customer service. Allow water to circulate through the filter for five minutes in order to clean the entire system.

2.How to Replace a DA29-00003F Water Filter

The DA29-00003F water filter is a replacement for the DA29-00003G, DA29-00003B, and DA29-00003A water filters, among others. In no way is it a substitute for the superior DA29-00003G filter, nor is it compatible with that more sophisticated filter. The replacement of an internalDA29-00003F water filter is described in the following instructions.

  1. The old water filter may be removed by turning it 45 degrees to the left to open it
  2. Gently take it out and throw it away — this will cause the water to cut off automatically
  3. To install the replacement water filter, insert it and rotate it 45 degrees to the right to secure it in place
  4. If the padlock sign on the water filter corresponds to the symbol on the water filter, you have completed the task successfully. To reset the water filter indication, press and hold the water filter reset button for three seconds.

Suggestions for improvement In the event that you are having difficulty removing the water filter, it is possible that there is excessive water pressure behind the filter. Remove the top two refrigerator shelves and use a stronger pull on the filter to get it out. If you are unable to squeeze the new filter into the available area, turn off the water supply valve and dispense a little amount of water. As a result, the pressure will be reduced, making it easier to install the new filter.

3. How to Reset the Water Filter Indicator Light on a Samsung Fridge

In addition to the water filter, every Samsung refrigerator that has one features a water filter indicator that tells you when it’s time to replace the water cartridge. The filter should be replaced once every six months regardless of whether or not the light changes color. This will ensure that you continue to drink the high-quality water that you have come to like. If you don’t change your water filter on a regular basis, it won’t function properly. Instead of drinking great-tasting, clean water, you’ll be forced to drink strange-tasting water that may include unwelcome toxins.

Blue indicates that your water filter is performing properly.

Red:Your water filter has reached the end of its useful life and it is time to replace it with a new one.

By pushing and holding the “Alarm / Hold for 3 seconds to Reset Filter” button for three seconds, you may reset the indicator light.

If your model has an inside control panel, press and hold the “Power Cool” and “Fridge” buttons for three seconds at the same time. This will return the indicator light to its original blue state.

4. How to Replace a DA29-00003G Samsung Fridge Filter

Instructions for internal filters are provided in the next section. The Samsung DA29-00003G water filter is always installed from inside the device itself.

  1. To remove the old water filter, twist it a quarter turn to the left to free it
  2. Then lift it out. Gently remove the old water filter and throw it away
  3. This will cause the water to be switched off automatically. Insert the new water filter and rotate it by a quarter turn to the right until it is secure. If the padlock sign on the water filter corresponds to the symbol on the water filter, you have successfully installed it. The water filter indication should be reset after installation by pressing the water filter reset button for three seconds after completion.

Suggestions for improvement In the event that you are having difficulty removing the water filter, it is possible that there is excessive water pressure behind the filter. Remove the top two refrigerator shelves and use a stronger pull on the filter to get it out. If you are unable to squeeze the new filter into the available area, turn off the water supply valve and dispense a little amount of water. As a result, the pressure will be reduced, making it easier to install the new filter.

5. Why You Need to Change Your Fridge Filter Every 6 Months

You might believe that you only need to change your refrigerator filter when the indicator light indicates that you should – but this is not the case. In some cases, waiting until the light goes red might be harmful to your health. A water filter prevents pollutants from flowing through the pipes and into your drinking water supply. When the water filter is no longer functional, all of the impurities that have been caught can now pass through into your drinking water, making it even worse than if you had not used a water filter at all.

Each Samsung water filter contains activated carbon filter material that has been approved for usage with a specific amount of water before the cartridge has to be replaced.

By absorbing impurities from water, activated carbon serves as a filter for such contaminants.

This occurs when there is no more surface area available for the absorption of additional pollutants and the filter’s capacity has been achieved.

How to Change Water Filter on Samsung Refrigerator

Purchasing the proper water filter for your Samsung refrigerator can be a difficult task, and you may be unclear of how to go about installing the filter correctly. Change your Samsung Water filter at least once every six months in order to ensure the health of you and your family members. Is it difficult for you to understand how to change the filter on your Samsung refrigerator? You will no longer be perplexed by the situation. Want to know “how to change a Samsung water filter”? Look no further!

A full explanation of “how to change a water filter on a Samsung refrigerator?” has been provided by Swift Green Filters.

Find the Correct Samsung Refrigerator WaterFilter Part Number for your Samsung Refrigerator

When it comes to replacing the Samsung water filter, the first and most important step is to identify the exact filter part number for your Samsung refrigerator. In order to accommodate different Samsung refrigerator models, several types of water filters are used. Samsung refrigerator water filters are divided into several groups based on their sizes and forms. Among these categories are: It is necessary to first identify the right water filter for your Samsung refrigerator before attempting to replace the water filter on the Samsung refrigerator.

You should, however, be aware of the model number of your Samsung refrigerator as well as the filter part number. Alternatively, if you are unfamiliar with any of these terms, you may quickly locate your appropriate Samsung refrigerator water filter by visiting this page:

Step by Step Solution to Learn How to Change the Water Filter on your Samsung Refrigerator

Swift Green Filters has simplified the process for you if you are faced with the question of “how to change Samsung water filter.” In order to make things as simple as possible for you, we will walk you through the process of locating the Samsung refrigerator water filter, removing the Samsung refrigerator water filter, and finally installing the Samsung water filter. You don’t need any technological knowledge to complete this task on your own.

  1. The following is the right replacement filter for your Samsung refrigerator: You may choose from a variety of appropriate water filters on the market that are designed to work with your Samsung refrigerator. While making a purchase, you may search for a certain filter part number or refrigerator model number. Make certain that you are selecting the appropriate filter for your Samsung refrigerator. Find the finest replacement water filter for your Samsung refrigerator. Examine your part to ensure you have the correct one: Each Samsung Refrigerator may utilize a unique model numberfilter part number. It implies that you must have the proper water filter for your refrigerator–not just any water filter will suffice
  2. And Locate the Samsung Water Filter on your refrigerator by following these steps: Finding the position of the Samsung refrigerator water filter is not a difficult task, but it might range from one Samsung refrigerator to another depending on the design
  3. Nonetheless, Prepare the filter for installation by doing the following: The following stage in the installation of a Samsung water filter is to prepare the filter for installation. To do this, you must first remove the plastic wrapping from the bottle and then unscrew the top cap. Make careful to switch off the water supply before removing the old Samsung refrigerator water filter so that the pressure does not become a hindrance during the removal process. Depending on the filter model you’re using, you’ll need to spin it counterclockwise, clockwise, or pull it straight out of the housing. Replacement of Samsung Water Filter: When replacing the old filter with a new one, make sure you follow the instructions in the handbook exactly. Simply pressing and holding down the water selector switch for three seconds will reset the Change Water Filter Indicator.

The following is a list of the most popular replacements for Samsung Refrigerator Water Filters that we sell. If you are currently using one of the refrigerator water filters listed below and would want to replace it, purchase the water filter that is most suitable with your Samsung refrigerator. In addition to DA2900020B,RF4287HARS,RF263BEAESR, HAFCIN, DA2900003B, DA29-00003F, and DA29-0002B, DA97-06317A, ES-1, and 9101 are also included in the list of DA2900020AH. ere, we’ve attempted to clarify all of the stages in a straightforward manner.

See also:  How To Flush Refrigerator Water Filter

If you are still having difficulties replacing the water filter in your Samsung refrigerator, please do not hesitate to contact Swift Green Filters for more assistance or advice.

Shop By Category

Swift Green Filters provides a large selection of filtering products. This product is a suitable Replacement Water Filter for your existing water filter. The above-mentioned brands have neither commissioned or supported the development of this filter. Swift does not represent any of the brands mentioned above. All of the brand names and part numbers that have been mentioned have been used solely for the purpose of reference. Swift Green Filters is an independently owned and operated company.

The maximum liability is equal to two times the cost of the goods.

Amazon.com: SAMSUNG – DA29-00020B-2P Samsung Electronics HAF-CIN Refrigerator Water Filter, white, (Pack of 2) , Packaging May vary : Appliances

a rating of one out of five stars Product that is a forgery. The Walmart product I purchased in-store was genuine! On March 21, 2020, a review was conducted in the United States. Don’t buy anything from Amazon since it is a phony. Read the paragraphs and pay close attention to the font size and style. The one on the right is the genuine article. I’ve always thought of it as being similar to the one that came with the refrigerator. Walmart has never failed to deliver on its promises. (It’s hard to tell from the photographs.) “Their” printer is a jerk!

I couldn’t believe Amazon would allow this to happen.

Even the most obvious signs are often overlooked by average customers.

Top reviews from the United States

On July 4, 2018, a review was published in the United States, confirming the purchase. I only gave it one star since there is no such thing as a zero. Because the overall rating was high, I didn’t bother to read the comments, which should have made it very clear that this is a low-cost imitation and NOT a genuine Samsung product. We were unable to get it inside the refrigerator, and I believe it may have really bent or destroyed the small portion that was inside the fridge. When comparing it to my actual filter, there are just minor variations to notice.

  • This has made me quite unhappy.
  • On November 5, 2018, a review was published in the United States of America.
  • They have the words “Genuine Filter” written all over them (the first indication that a fraud is taking place), and they are attempting to deceive you into believing that they are “genuine Samsung,” which they are not.
  • There is a statement on the package claiming they are created from “globally sourced components” (aka China).
  • Consider how much water you use on a daily basis.
  • All of this is purely my opinion.
  • Don’t buy anything from Amazon since it is a phony.

The one on the right is the genuine article.

Walmart has never failed to deliver on its promises.

It’s a phony product, to be honest.

At the very least, get a printer that produces labels at a resolution of 300dpi.

I’m not going to let my $3.5k smart fridge go to waste!

The Walmart product I purchased in-store was genuine!

Don’t buy anything from Amazon since it is a phony.

The one on the right is the genuine article.

Walmart has never failed to deliver on its promises.

It’s a phony product, to be honest.

At the very least, get a printer that produces labels at a resolution of 300dpi.

I’m not going to let my $3.5k smart fridge go to waste!

Purchase that has been verified If I had the option, I would have given less than one star.

It has only lasted approximately three months and is already filtering the water at such a sluggish rate that it is practically hard to use it properly.

Their argument is that it is Amazon’s responsibility that THEIR filter has malfunctioned, not their own.

My money was completely squandered.

I’ll make an attempt to return, but I’m not optimistic!

Purchase that has been verified All of this is based on my personal opinion: This product is unquestionably a forgery.

For comparison purposes, I’ve placed the new “Samsung” filter (on the right) next to the one I’ve been using for more than 6 months (left).

I did not attempt to flow water through them because, given that they had failed my visual assessment, I was concerned that they would similarly fail to filter and contain water if I tried (something other reviewers have noted).

Once again, this is solely my viewpoint.

The review will take place in the United States on July 10, 2020.

I’ve included images that demonstrate the inauthenticity of the product.

There are several critical components missing from the replacements (particularly, the authentication tag), so proceed with caution if you decide to purchase or use these filters.

I’m not sure if this is true for all of the filters, but the ones I received were definitely not “Genuine water filters,” as they were advertised to be on the package.

On December 21, 2017, a review was conducted in the United States.

The fact that this is a part of a public water system means that it is extremely clean to begin with; it is just a required element of the system if you want to utilize the water in the refrigerator’s door function.

On November 25, 2015, it was reviewed in the United States and verified as a purchase.

However, they perform as claimed, and I have confidence in them.

Another point to add is that many evaluations of third-party filters would express delight in the fact that “the water flow is far better than with the Samsung filter.

I’d also want to point out that the Samsung OEM filter is NSF 53 certified, however none of the third-party filters I’ve looked at has received this certification to far (most have no certification at all, and one I found was “independently certified at NSF 42” but has no NSF emblem on it).

On March 11, 2021, a review will be conducted in the United States.

Using a knock off filter had been working perfectly for me for many years with no issues.

One of them worked perfectly.

He was kind and informed me that my ice maker motor had failed.

Within three days, the water and ice were no longer functional.

I worked for three days and then stopped.

In the days before the second repair appointment, I obtained and fitted an original Samsung filter that I had previously purchased.

Both ice and water immediately began to function properly. To be sure I didn’t miss my service appointment, I waited until the very last minute. It has been more than two months since then, and everything is still running smoothly!

Top reviews from other countries

5.0 stars out of 5 for this product Authentic. On September 2, 2019, a reviewer in the United Kingdom expressed satisfaction with their purchase. It’s the perfect size and shape for my refrigerator. 5.0 stars out of 5 for this product This is a genuine item. On February 10, 2019, a reviewer in the United Kingdom expressed satisfaction with their purchase. This is a genuine item that works in my refrigerator. 4.0 stars out of 5 for this product The same as the original, but at a better price On May 25, 2016, a reviewer in the United Kingdom stated that they had made a verified purchase.

When compared to purchasing directly from the manufacturer, this filter offers substantial savings.

5.0 stars out of 5 for this product Exceptional value Purchased on February 23, 2020 in the United Kingdom and reviewed on February 23, 2020 4.0 stars out of 5 for this product Samsung Water Filtration Systems On May 6, 2020, a reviewer in the United Kingdom expressed satisfaction with their purchase.

How to Reset Filter Light on Samsung Fridge [2022]? (Solved)

It is standard on the vast majority of Samsung refrigerators to include filter light indicators, which inform users when it is time to replace the water filter. Moreover, after changing the filter in your Samsung refrigerator, you will have to reset the filter light on the appliance. What, though, is the reason behind this? Generally speaking, a water filter may be used for a maximum of six months before it has to be replaced. Waterline replacement could be essential, though, depending on what sort of water is passing through the waterline in question.

Unless and until you detect a difference in flavor that you would not have noticed without the filter light, you will be unable to identify whether or not your filter requires replacement.

You may also be interested in:How to Reset Your Samsung Refrigerator When you open the door of your Samsung refrigerator, the noise stops.

The Operation of the Samsung Water Filter Indicator

In excellent functioning condition, the Samsung water filter will exhibit a blue or green color, depending on the type that you have installed on your system. The hue changes to orange or light pink after 5 months or 450 gallons of water has been added. This hue shift is typically a sign that it is time to upgrade the water filtration system in your home or business. After 6 months or 500 gallons of water have been utilized, the water filter indicator will turn red on your water filter. When you see this red light, it indicates that it is time to replace the water filter.

Furthermore, if you reside in a place where there is an excessive amount of limescale in the water supply, you will need to change your water filter more frequently than every six months.

Indicator for the presence of a water filter

After five months or 450 gallons of water, the water filter indicator light must first become orange, and then red after six months or 500 gallons of water. After turning orange, the light must next turn red. The hue of the light is determined on the model that you have purchased. It might be either green or blue in color. Identifying the multi-function button or buttons on your display that control the water filter indicator is required in order to restore the water filter indication to its default state.

Exemplifications of Various Models

Please keep in mind that the models shown in the images below are merely a few examples of the many different designs available. Take a look at the digital display panel on your refrigerator and look for traits that are similar to these.

What you need to know about how to reset the filter light on a Samsung refrigerator (steps to follow on different models)

Holding down the FILTER RESETbutton for about two seconds is required while operating a Samsung refrigerator to turn off the red filter symbol located on the door of the refrigerator. Consult your refrigerator’s owner’s handbook if you are unable to locate the FILTER RESET button, which is usually placed on the dispenser controls (on the front of your refrigerator). Other versions can only be operated by pressing and holding down either the “WATER FILTER” button or the “ICE/WATER” button for three seconds at a time.

Samsung refrigerator model RF28K9070SR has a filter reset.

If you have an RF28K9070SR model, you may reset the filter by pressing and holding the ICE-MAKER button for roughly 3 seconds after turning it off. As a result of performing this step, the filter indicator will be reset.

Resetting the filter light on a Samsung model RF23J9011SG/AA – instructions

It is necessary to hold down the CRUSHED/HOLD button on your RF23J9011SG/AA for three seconds in order to reset the water filter light on your device. Instead of remaining on, the color of its indicator should go from red to OFF instead of remaining on. The following are the steps to follow in order to reset the water filter on a Samsung refrigerator with a French door style. There are Samsung refrigerators available, such as the Samsung refrigerator RF260/BEAESR/AA. Samsung refrigerators are also available.

You should bear in mind that, in order to activate the internal controls on devices with internal controls, you must simultaneously press and hold the buttons FRIDGE+POWER COOL for a total of three seconds.

Model DA29-00003G of the Samsung refrigerator has a filter reset light.

The ALARM/HOLD button must be held down for three seconds while the replacement warning light is turned off to reset it.

Model number RF24R7201SR/AA of the Samsung refrigerator.

It is recommended that you push and hold the FILTER RESET button (for 3 seconds) if you have just replaced the filter in your Samsung RF24R7201SR/AA refrigerator to turn off the reset signal on the refrigerator.

See also:  How To Replace A Water Well Pump

Samsung refrigerator water filter reset RF28K9070SR/AA

In order to clear the water filter message, the CRUSHED ICE button must be pushed and held down for three seconds.

RF23J9011SR is the Samsung refrigerator filter reset code.

The water filter alarm on a Samsung refrigerator with model number RF23J9011SR may be reset by pressing and holding the button “CRUSHED/HOLD” for three seconds.

RF263BEAESR is the Samsung refrigerator filter reset code.

If your RF263BEAESRSSamsung refrigerator water filter does not reset automatically, the following process should be followed: Press and hold the ICE TYPE/WATER button on the controller for three seconds to activate it.

Instructions for resetting the Samsung RF28R7351SG water filter (applies for most 4 doors Samsung refrigerators)

In order to reset the warning signal, the CRUSHED LIGHT INDICATOR button must be pushed and held down for three seconds.

If the reset light signal does not turn off, there are some other options to attempt.

Briefly said, if replacing the filter does not result in the red light going off, you can also try the following steps:

  • Check to determine whether any of the buttons are currently locked
  • Please double-check that the buttons are actually “unlocked,” or else the Samsung refrigerator filter reset process will not work properly.

Alternatively, you may refer to your guide book once again for the procedures on how to unlock the controls if you desire them. It is conceivable that the filter alert light is still flashing because the freshly fitted filter was not put in the right location. Open the door, take a look at the fitting, and check sure everything is in its proper place.

  • Double-check to make sure the correct filter was installed. As a final option, if you did not use an authorized product, the light notification might not go and you might have to switch out the new filter in order for the system to function properly again.

OUR FINAL THOUGHTS

You should now be able to comprehend how to reset the filter light on a Samsung refrigerator, which we hope has been helpful (and probably you have already gotten rid of the warning). Just one more issue to mention: the majority of Samsung refrigerator models are equipped with a “LOCK” button, which is used to lock the settings, and it is commonly this button that is faulty when the Samsung fridge water filter light does not dim when you attempt to switch it off. For the water filter light to be correctly reset, it will be required for you to unlock the controls; thus, try holding down the flashing LOCK button for 3 seconds and then retrying the procedure.

If the steps indicated above do not work, consult your guidebook to determine the proper way.

FREQUENTLY ASK QUESTIONS

Pressing and holding down either of the buttons on the side of the refrigerator for three seconds each is the most common method of resetting the Samsung refrigerator water filter. The FILTER RESET button may be found on the right-hand side of the screen, at the bottom. It is possible to use either the “WATER FILTER” button or the “ICE/WATER” button. If, on the other hand, your Samsung refrigerator filter light does not reset, then check to see if the buttons have been locked and then unlock them before attempting to reset the light again.

What is the procedure for turning off the filter light on my Samsung?

Identifying the multi-function button or buttons on your display that control the water filter indicator is important in order to restore the water filter indication to its default state. Once you have done this, press and hold the button(s) for a few seconds until the light turns green.

What is causing my Samsung refrigerator’s filter light to not reset?

If the light does not turn off after many efforts, call a professional to have the filtration system repaired or serviced. It should be possible to restore the indicator light to its previous blue color and functionality after the filter has been changed. Unless you manually reset the red filter indication on your Samsung refrigerator, it will remain illuminated at all times.

Hello, my name is Khelly. Count on me to be your go-to tech specialist for all of your Samsung Products and Information need. Finding a solution to your digital difficulties shouldn’t be as difficult as it is in everyday life. Allow me to assist you with that!?

How To Change Your Samsung Fridge Water Filter

Samsung refrigerators are among the most popular models on the Australian market. Homeowners like the built-in usefulness of their cabinets because of the diverse selection of functions and styles available. On a daily basis, the Samsung refrigerator filter supplies your family with clean, fresh, filtered water and ice. Each Samsung water filter has a lifespan of around six months, however some may need to be replaced sooner if they are used often or if the water is exceptionally harsh. The fact that your Samsung refrigerator’s filter indication light has begun to illuminate indicates that it is time for you to replace your old filter with a new one.

Where Is the Water Filter on My Samsung Fridge?

In order to purchase a new Samsung water filter, you must first determine the model of Samsung water filter you currently own. You will be able to purchase the appropriate replacement because of this. Discount Fridge Filters assists clients in locating the appropriate filter for their refrigerators depending on the model number of the refrigerator. Other brands of refrigerator filters may be used to replace the filter in a Samsung refrigerator and perform just as well; however, you must know the model number of your refrigerator in order to obtain suitable fridge filters.

If you are having trouble identifying the model number of your Samsung water filter, you may watch the video below.

It is possible for your water filter to be installed in three different locations.

In some versions, the water filter will be located on the top right inside or at the back of the refrigerator.

Do You Have To Turn Water Off To Change Your Samsung Refrigerator Filter?

Samsung refrigerators with internal filters are equipped with an auto shut off valve, which eliminates the need to turn off the water to change the filter. Because customers have experienced installation issues as a result of shutting off the water, causing air locks and other issues, we do not recommend shutting off the water supply. When customers turn the water supply back on, they may experience sputtering water or even no water coming out of the faucet. Samsung refrigerators with external filters, on the other hand, nearly usually require the water to be turned off before the filters can be swapped out or replaced.

If this is the filter you require, turning off the water supply is a critical step in ensuring that you do not have a flood of water from this connection when changing your filter.

When high water pressure prevents the filter from being removed or re-installed, it may be necessary to turn off the water supply to a Samsung fridge with an inbuilt filter. However, reducing pressure by dispensing some water is usually always a preferable choice.

How To Change An Internal Water Filter on a Samsung Refrigerator

Determine the placement of the water filter in your refrigerator. 2. Remove the old filter by lifting the protective cover (if your filter type has one) and turning it counter-clockwise to dislodge it. Alternatively, if it is difficult to lift, it is possible that pressure has built up; dispense some water and try to relax it before tugging it again. 3. Take your new filter out of the packing and remove the protective cover from it. 4. Press in the new filter and spin it clockwise until its lock symbol is aligned with the arrow.

  1. Replace the old filter.
  2. Replace the filter cap, if your filter type has one, and run several litres of water to confirm that the water has been adequately filtered and that any air has been drained out of the line.
  3. This assures that there will be no leaks in the future.
  4. Reset the filter-indicator light on the inside of your refrigerator.
  5. The indicator light should return to its original state of green.
  6. You may also go to the user manual that came with your Samsung refrigerator for complete instructions on how to change the water filter and reset the indication light on the refrigerator.

How To Change An External Water Filter on a Samsung Refrigerator

1. Locate the isolation valve, which should be situated somewhere along the water supply line to the refrigerator. Turn it off if it’s on. Using the water outlet located near the refrigerator, depressurize the system by drawing a large glass of water. 2. Have a bucket and a towel handy in case there is a tiny amount of water spilled throughout the operation. The old filter should be removed by depressing the locking collars at either end of the filter with your thumb nail (or something similar) while simultaneously pulling out the water supply line from the filter.

  • It is possible to hold down the locking collar with your fingers or with a solid edged item, which will allow the hose to slip out with relative ease.
  • We recommend that you use a sharp object, such as a Stanley knife.
  • 4.
  • For this, you may either place the filter under a running faucet and let the water to flow directly into a sink, or you can submerge the filter in a bucket or other container of water.
  • 5.
  • The line will go in approximately 5 – 10mm and you will be able to fully put the filter into place.
  • After you’ve placed the filter in the bucket, switch on the water supply and allow approximately 5 litres of water to run through the filter and into the container.

After you have turned off the water supply, connect the line that flows into the refrigerator.

7.

8.

If the filter light on your Samsung refrigerator does not come back on, press and hold the “Ice Type” or “Moisture Control” buttons as well as the Child Lock button for three seconds.

Avoid holding the buttons for an excessive amount of time, since this may force the procedure to restart, requiring you to release all of the buttons and hold them again until the light changes to green again.

You may also go to the user manual that came with your Samsung refrigerator for complete instructions on how to change the water filter and reset the indication light on the refrigerator.

Can I Run My Samsung Refrigerator Without the Water Filter?

Water filters are designed to eliminate toxins such as lead, mercury, chlorine, and other contaminants from your drinking water and ice, among other things. The majority of Samsung refrigerators may still work well even if they do not have a water filter installed. In spite of the fact that rotary valves in your refrigerator may bypass the water filter and provide you with water even when there isn’t a water filter installed, this does not imply that you should continue to use your Samsung refrigerator in this manner.

At first, you may be unsure about how to replace your water filter.

In the event that you do not change your old filter after 6 months, you may face mineral buildup, which may result in your refrigerator experiencing costly malfunctions.

Tips on How to Change Your Samsung 3G 3F Filter Head Alignment

A misaligned head of a Samsung 3G 3F water filter might cause difficulties if the filter is used. If you have a Samsung 3G 3F water filter, you may face problems if the head gets misaligned. We have covered the basics of this straightforward repair procedure in a few steps. You may quickly correct the alignment of your water filter by watching the video provided below.

Where Can I Buy a Samsung Refrigerator Water Filter?

At Discount Fridge Filters, we can assist you in selecting the appropriate filter and ensuring that it is compatible with the Samsung refrigerator model that you have purchased. On the market, there are many different types of water filters to choose from, and you can save money by selecting one from our extensive inventory. Please do not hesitate to contact us at any time if you want assistance in selecting the appropriate water filter. We would be pleased to answer any questions you may have and to provide you with guidance on how to go about installing it.

Leave a Reply

Your email address will not be published.