Where Is My Rv Water Pump Located

Where Is The Water Pump Located In RV? (Motorhome – Trailer)

A is the highest level of classification. RVs are not particularly small, but when compared to a house, they provide significantly less space for you as well as all of the equipment required to power the amenities on board. Therefore, when it comes to positioning the water pump for the freshwater tanks, RV builders must think outside the box. What is the location of the water pump in the RV? In certain RVs, they may be tucked away behind one of the sleeping arrangements. On another occasion, you may need to remove a couple of drawers from a kitchen cabinet in order to get to the water pump.

Continue reading our post to find out more about where your RV’s water pump is located and how it works.

RV Water Pump 101 – Where to Find It

Where is The Water Pump Located in RV?

In most cases, the water pump will be situated within 2 feet of your freshwater tank, if not closer. Another consideration is how that fits in with your motorhome’s overall configuration. By that, we mean that you might place the pump beneath a bed, a cabinet, a floorboard, or anything else that is within 2 feet of your water tank.

Travel Trailer Water Pump Location

This is a game of concealment and discovery. When it comes to travel trailers, the manufacturers prefer to conceal certain components and then leave you to hunt for them after you purchase the trailer. The water pump for this particular RV model, according to some reports, is less than three feet away from where the municipal water intake valve is positioned. As a result, your travel trailer’s water pump might be located anywhere on its outside, as not all manufacturers install their water pumps in the same spot as their rivals, much alone on various types of travel trailer.

Motorhome Water Pump Location

Your motorhome’s brand and model will determine how much space you have. As far as Fuzion is concerned, theirs is hidden behind a panel in a storage cabinet, or it may be found on the curbside of the RV, in the front storage compartment, behind the water heater. Other versions may have it close to both the hot water heater tank and the fresh water tank, but it may be before the freshwater drain on the other hand. Check your owner’s handbook to check if there is a diagram depicting the placement of the switch in question.

Best Location for RV Water Pump

The majority of RVers believe that the optimal position for the water pump is close to the fresh water tank. That is your water supply, therefore it seems to reason that the pump would be located near to it in order to optimize water pressure. Alternatively, a desirable placement would be at the most easily accessible location possible. Water pumps have a tendency to break down over time, and in order to keep costs low, they must be located in a readily accessible location that is not difficult to operate on.

Heartland RV Water Pump Location

The water heater for the Heartland Trail Runner is hidden under a panel that is also hidden beneath the couch sleeper, making this a bit of a treasure hunt. The North Trail 24BHS model, on the other hand, had the water pump installed beneath the range. Another panel had to be removed in order to obtain access to it once more.

A common complaint about water pumps is that they create a lot of noise. That implies that the manufacturer will look for the best location to mask the noise and provide you with greater comfort while you are resting in your RV.

Grand Design RV Water Pump Location

The water pump for the Xplor 240Ml model is housed in a cabinet on the left side of the entry, just inside the door. However, there is some good news: the access panel is conveniently located directly next to the RV’s entry on the outside. There should be a grill in the area where the access panel is, indicating where the water pump may be found. Newer versions, on the other hand, have relocated the battery to the underside of the dinette bench, which is more convenient.

Forest River RV Water Pump Location

A number of firms have developed a reputation for placing water pumps in unusual and fascinating settings. Typically, they are hidden behind panels or in extremely inconspicuous locations. Example: The Windjammer’s water pump might be concealed behind a cabinet door that has been bolted shut. Alternatively, it might be located beneath the sink cabinet, near the water heater. If you trace the city water inflow line and the pipes that come out of the fresh water tank or hot water heater, you should be able to locate the problem.

Keystone RV Water Pump Location

You should check for a secured panel on the left side of your queen bed and behind the bedside table if you have a Bullet or an Outback model. Robertson screws keep the panel in place and there are around 5 to 6 of them. Many owners recommend turning on your water pump and listening for any sounds it might make. This will assist you in finding it more quickly. The water pump for the 2017 Hideout is not near the top of the bed, but rather beneath it.

Springdale RV Water Pump Location

The placement of your water pump will be determined by the year it was manufactured as well as the model number. Owners have reported that their water pump was conveniently positioned beside the queen bed, just next to where the gravity fill valve was. A third location may be beneath the sofa, next to the fresh water intake, or anywhere in between. Another model should have it situated between or behind the fresh water filler and the city water connection, rather than in front of it. Alternatively, it might be hidden behind a carpeted panel on the left bedside table.

Some Final Words

As you can see, locating your waterpump may need some effort on your part. As a result of wasting so much time attempting to locate the part, winterizing it becomes a nuisance. RV designers, on the other hand, have had to become inventive throughout the years, given the constraints of operating in a compact vehicle. Go to the RV manufacturer’s forum and chat to other RV owners who will be able to provide you with further information. They have also gone to the location.

Where is water pump located in RV?

It may be found in the front storage compartment, behind the control panel. It is located on the curb side, directly behind the water heater. If you remove the carpeted panel (which extends from the front to the rear of the RV) that attaches to the plastic panel in the convenience center, you will be able to get to it from that location. It is more likely to be found on the tank side of the drilling rig. Fill the tank with water and open the doors to your storage areas. While you’re outdoors, ask someone to switch on the water pump for you.

  1. Also, why does my RV’s water pump continue to operate indefinitely?
  2. Something as easy as a loose connection may cause this, or something as inconvenient as a fracture in one of your pipes or a defectiveRV water pumppressure switch can cause this.
  3. ANSWER: Greetings, Nicole.
  4. It is common for RVers to leave the pump running when connected to city water, which results in the water being pumped out of their freshwater holding tank every time they use a faucet or flush a toilet.

How do you remove air out of a water line in a recreational vehicle? To re-fill this air pocket, do the following:

  1. Water heater should be turned off, as well as the cold water supply line. In the RV, turn on the water faucet. Pulling out on the handle of the Pressure Relief (PT) Valve will enable water to flow through. Release the handle on the PT Valve, and it should snap shut. To use, close the faucet and switch on cold water supply
  2. When the tank fills, the air pocket will be pushed back out.

Where is my water pump?

12-13-2019, 10:07 AM 1
Junior MemberJoin Date: Oct 2013Location: MassachusettsPosts: 1 Where is my water pump?


I own a 2013 Forest River Freedom Express 282BH Travel Trailer. I can hear the water pump but for the life of me I can’t find it. For years I have been putting Antifreeze in my on board tank and pumping it throught the lines. Fortunately I don’t dry camp so it alright, but i would prefer to bypass the tank.Thank you,Ken in the Northeast.

12-14-2019, 07:59 AM 2
Misfit AdventuresJoin Date: May 2018Location: Sharbot Lake OntarioPosts: 165 Under sink?
12-14-2019, 08:51 AM 3
Senior MemberJoin Date: Apr 2016Location: Port Charlotte Fl/Hinsdale MaPosts: 4,823 If you can hear it you can find it. It is hidden behind a screwed on panel.2 square head screws. Maybe under a drawer. Behind a drawer. under a bed. Mine is in the pass thru storage area behind a panel. It will be close to the city water hook up.
12-14-2019, 08:58 AM 4
Senior MemberJoin Date: Jan 2019Location: Reno, NVPosts: 1,653 Crawl around on your hands and knees and listen around all the nooks and crannies on the floorplan. The pump is inside an interior structure or under a bed where the pump sound is the loudest. Bring a flashlight and an electric screwdriver with a2 square drive bit to remove a panel. A good start to look for the pump is near where the fresh water tank is located._2018 Ram 2500 Tradesman, CTD/CC/SB/4X4/Equalizer WDH2019 Forest River Surveyor Legend 19BHLE
12-14-2019, 11:30 AM 5
Senior MemberJoin Date: Oct 2016Location: Southern INPosts: 1,003 On my Coachmen Apex, the water pump is in the bathroom behind a panel where the towel cubbies are.Good Luck finding yours_Gerard2017 Coachmen Apex 269RBKS with Summit Pkg.2014 Ford Expedition with factory installed HD tow pkg.Blue Ox SwayPro WDH
12-14-2019, 01:38 PM 6
Senior MemberJoin Date: Mar 2013Location: CanadaPosts: 485 On my 2012 coachman 292bh, it�s under the rear bunk bed where the water heater is and directly above the freshwater tank
12-14-2019, 02:16 PM 7
MemberJoin Date: Aug 2014Location: Langley, BCPosts: 32 Look behind cabinet doors for partial shelves and panels held on by screws. I found mine beside my oven under a shelf where the lower part was behind a wood panel. Now I just leave that panel off as it is behind a cabinet door. Check under your bed if it lifts, in a front storage compartment from outside (the worst space possible), in the bathroom or in the kitchen. Good luck and hope this helps._Dan2020 Chevy Silverado RST 2014 Surveyor Select SV 2642020 – 4 Nights Camping – Covid and Surgery does that.
12-14-2019, 02:54 PM 8
Senior MemberJoin Date: Oct 2014Location: Central FloridaPosts: 555 If you have the bedroom slideout take the night table draw out and you will see it.
12-14-2019, 05:03 PM 9
Senior MemberJoin Date: Apr 2017Location: Berks County, PAPosts: 203 On a small Coachmen Viking


My water pump is in the front cross-through compartment. It is behind a small boxed panel on the drivers side. Amazing how many places they stick these things.

12-14-2019, 05:48 PM 10
Senior MemberJoin Date: Oct 2016Location: Southern INPosts: 1,003 Quote:Originally Posted byWaterops1My water pump is in the front cross-through compartment. It is behind a small boxed panel on the drivers side.Amazing how many places they stick these things.Aint it the truth?_Gerard2017 Coachmen Apex 269RBKS with Summit Pkg.2014 Ford Expedition with factory installed HD tow pkg.Blue Ox SwayPro WDH
Posting Rules
Youmay notpost new threadsYoumay notpost repliesYoumay notpost attachmentsYoumay notedit your posts


BB codeisOn SmiliesareOn code isOnHTML code isOffTrackbacksareOff PingbacksareOff RefbacksareOff


Forum Rules

Disclaimer:This website is not affiliated with or endorsed by Forest River, Inc. or any of its affiliates. This is an independent, unofficial site.All times are GMT -5. The time now is09:51 PM.

How to Do Your Own RV Water Pump Replacement

In most cases, replacing an RV water pump is not a part of your usual maintenance regimen when you own a recreational vehicle. After all, a water pump should endure for many years under typical operating conditions if it is properly winterized during the off-season period. So, how will you know whether it’s time to do routine maintenance on your water pump or whether it’s time to replace it entirely?

When Do You Need to Do an RV Water Pump Replacement?

It’s most probable that you’ll notice that your RV water pump needs to be replaced when the water no longer runs as smoothly as it used to. A faulty water pump is most likely to be found when you turn on your pump and open a faucet inside your RV. If you switch on your pump and open a faucet but the pump does not come on and the water does not run, the water pump has most likely failed. In the days or weeks leading up to a total shutdown of the system, it’s probable that you observed that your water pressure was becoming more fussy or variable than usual.

The presence of water seeping from the pump or peculiar noises emanating from the unit are two more signs that it may be time to replace your water pump.

Whatever the cause for your consideration of changing your RV’s water pump, we’re here to guide you through the process of doing it on your own time.

Now that we’ve taken care of that, let’s get this party started!

What You’ll Need for an RV Water Pump Replacement

The majority of the things on your list are tools that you most likely already have on hand or that you can quickly obtain from a nearby hardware shop. A drill or screwdriver, wire cutters, a wire stripper/crimper, spade connectors, a basin or bucket to catch some water, and maybe even a sponge or cloth for the same reason are all equipment that you will need. Make sure to account for the fact that you will most likely need to acquire a specialist item such as the water pump itself ahead of time.

(but check out our post about the 5 Best RV Water Pumps to see if a different choice would be best for you).

To the extent that you like to see things rather than read them, you’ll probably appreciate our DIY tutorial video, in which we demonstrate how we changed our water pump.

How to Do an RV Water Pump Replacement Step-By-Step

Once you’ve gathered your tools and new parts, you’ll be ready to begin the process of replacing the pump. It’s time to say goodbye to the old and hello to the new! If you follow the methods outlined below, it should be rather simple:

1. Turn Off City Water and Water Pump

Starting with cutting off the city water connection and your water pump, you may begin this do-it-yourself process.

The first step you should do whenever you are working on your RV’s plumbing is to cut off the city water if your RV is linked to a municipal water supply. Additionally, you’ll want to turn off the water pump.

2. Remove Water Pump Fuse

In order to increase safety, locate the fuse for your water pump on the fuse panel and pull it. Additionally, you should unplug the fuse that powers the water pump as an extra precaution. This may be found on the 12-volt electrical panel in your home.

3. Turn on a Faucet

Some individuals like to turn on all of the faucets at the same time in order to bleed out any remaining water pressure in the plumbing system. Although this may be a more expedient method of draining the water, just one tap will be required. Once a single faucet has gone dry, you can proceed to the next phase in the process.

4. Disconnect Water Pump from Latching Controller if Applicable

Our RV’s water pump is located exactly beside the latching controller, as shown in this photograph. A latching controller enables an RV to use numerous on/off switches for the water pump, which saves space and time. You will be able to turn on and off the water pump from several locations, such as the bathroom, water bay, or kitchen. If your system is equipped with a latching controller, it is most likely to be found close to the water pump. Your RV should have a box with many wires coming out of it that feed into the different water pump switches.

  1. Continue until the power is completely disconnected.
  2. Remove the black ground wire from the latching controller and save it aside for later use.
  3. Our positive line is likewise linked to a yellow wire, and it’s possible that yours is set up in a similar manner.
  4. After you’ve removed them, cut the yellow wire that connects to the connection.

5. Remove Inlet and Outlet Lines from Pump

Before you begin to remove the pump, place a bucket or bowl below it to catch the debris. Expect water to seep out when you unscrew the intake and outlet lines on both sides of the valve. To avoid damaging the plastic fittings, we recommend that you detach the lines using your hands rather than with a screwdriver. If the fittings are too tight, pliers may be required to get them started; however, you must be careful not to damage them while doing so.

6. Remove Screws Holding Pump in Place

The pump may easily be unscrewed from its mounting bracket after the inlet and output hoses have been detached from the pump.

7. Remove Inlet Filter and Clean It

When we take out the filter, we have a fantastic chance to clear out any debris that has accumulated over the course of time. On the new pump, you’ll need to replace the inlet filter from the old one, which you removed from the old. The filter may be unscrewed with the use of a crescent wrench.

Following its removal, open the filter (the two pieces of the filter should twist apart from one another) and remove any debris that may have accumulated inside. If it’s really blocked (or just extremely old), it may be necessary to totally replace it with a new one.

8. Install Filter on New Pump

Take note of the directional arrows on both the pump and the filter. Before you screw the filter onto the new pump, double-check that both arrows are pointing in the same way. Pump and filter both need to have an arrow(s) pointing in the direction of water flow to be properly installed. Install the filter on the side of the pump that corresponds to the direction of the arrow, making sure that both arrows point in the same direction as the filter. Installing it is as simple as screwing the fitting from the new pump into the filter using a crescent wrench.

To secure the fitting in place, press the clip all the way down.

9. Strip Wires and Crimp-on Connectors for Latching Controller

The black ground wire on the pump should be located and stripped of any remaining insulation at the wire tip before being crimped into a spade connection. Gently tug on the connector to verify that it is crimped tightly. After twisting the red and yellow wires together, crimp them together with a spade connection (again, your wiring may change somewhat depending on the RV brand and model you have). If you’re still not sure about the links, you can refer to the snapshot you took before you started.

Twist the exposed ends of the two wires together before crimping on a spade connector to secure the connection.

10. Mount Pump into RV with Existing Screw Holes

In most cases, you may reuse the same mounting position and screw holes for the replacement pump (the mounting hole pattern is fairly standard). While the actual replacement pump type will vary depending on the one you pick, the previous model of the pump is frequently identical to the replacement model. Four screws are used to secure the new pump in place.

11. Connect Inlet and Outlet Water Lines to Pump

By hand-screwing the input and outlet water lines to the new pump, you may quickly and easily reconnect everything. Once again, use caution when handling the fittings. No special tools should be necessary because they are often intended to be finger-tightened.

12. Connect Pump Wires to Latching Controller

Connect the positive lead (in our example, the yellow and red wires) to the latching controller first, then the black ground wire, and then the negative lead to the ground wire.

13. Re-Install Water Pump Fuse and Turn on Water Pump

Replace the fuse that you removed from the electrical panel in its rightful placement on the circuit breaker panel.

14. Turn on Water to Ensure Proper Operation

You may now activate the water pump by pressing one of the switches. Simply turning on a faucet will allow you to test the operation of your new pump. It is usual for there to be some cavitating and sputtering while air is cleared from the pipes, but after that you should notice steady water pressure and flow, and the water should cease when you turn off the faucet.

15. Check Water Connections for Leaks

As soon as the water is flowing freely, turn off all taps, but leave your pump running to retain pressure in the system at a constant level.

Ensure that the system is pressurized before checking for leaks at all connections at the pump and inline filter. If necessary, tighten them.

Additional Tips for Completing Your RV Water Pump Replacement

Hopefully, you were successful in replacing your old water pump with a new one by following the methods outlined above. In the event that you run into some difficulties, here are a few additional possibilities that you may want to consider exploring.

Once New Pump is Installed, You May Need to Bleed Air Out of Lines

When you initially turn on the water, it’s usual for the plumbing to include air bubbles, so keep the water pump running until the air bubbles have been removed. Alternatively, you may choose to turn on many faucets at the same time to enable the water to move through the pipes. It may take a number of tries, including turning the faucet on and off again, to get all of the air out of the system.

Alternate Option to Removing Fuse

Instead of pulling the fuse, you can unplug the RV from the power and flick the battery disconnect button to ensure that no electricity is sent to the appliances in the RV.

Use Butt Connectors if You Don’t Have A Latching Controller

As previously stated, not all recreational vehicle types are equipped with a latching controller. You can easily connect your new pump to the existing power lines in your RV using butt connectors (also known as end splices), which are available at any hardware store. In the end, replacing an RV water pump is a reasonably straightforward repair that can be completed in an afternoon with basic tools. Projects like this allow you to become more familiar with your RV and have a better understanding of how the system operates, which may be valuable for future troubleshooting.

Congratulations on the installation of your new water pump system!

(Did you catch what we did there?) It’s one of the things we like most about RVing is being able to have all the comforts of home with us no matter where we happen to be camping for the night.

Geek Out with Us Every Week

Sign up for our newsletter to stay up to date on anything RV-related. Every week, we provide free RVing tips, tactics, product reviews, and other information to our online community of RVers and campers. This is a great opportunity for you to share your knowledge and experience with us, whether this is your first time on the road or you’re a seasoned pro!

Where is the water pump located

09-07-2017, 11:19 AM 1
Junior MemberJoin Date: Sep 2017Location: S LakePosts: 3 Where is the water pump located


We have a 2017 Fuzion 371 toy hauler – we recently dry camped and the water pump pulsed on/off every time we used a faucet.I did some research and found that the water pump needs to be adjusted.Well that would be great if I could locate it.The manufacturer was no help – Can anyone tell me where it is located? Thank you

09-07-2017, 01:47 PM 2
Senior MemberJoin Date: Nov 2012Location: FruitlandPosts: 3,358 Before adjusting the water pump. Are you 100 % sure you got all air out of lines. All my RVs take awhile to get all air out and thats how they act until it’s gone._2013 24RKSWE (27ft TT) Cougar 1/2 ton series SOLD 10-20212013 Ford F350 4×4 CC 6.7 engine, 8 ft bed, 3.55 rear end, lariat package Retired from Oregon State Police in 2011 than worked another 9.5 years as a small town traffic cop:As of 05-2020, I am all done with 39 years total police work. No more uniforms for me.
09-08-2017, 02:20 AM 3
Senior MemberJoin Date: Aug 2017Location: LafayettePosts: 1,068 I think someone mentioned on here that Fuzion locates theirs behind the convenience center and behind panel in storage compartment. That’s where mine is also, according to tech, though I did notice a removable panel under or sink in the 1/2 bath that I need to check see whats in there._2015 Ram,3500,Dually,B W,4.10s,Aisin,Limited,Silver2018 Raptor,428SP w/full body paint2012 Harley, Ultra Limited
09-08-2017, 10:20 AM 4
Junior MemberJoin Date: Sep 2017Location: S LakePosts: 3 We used the pump for 3 days and it pulsated the entire time.
09-08-2017, 10:47 AM 5
Site TeamJoin Date: Dec 2015Location: Kansas CityPosts: 3,879 Run it and listen to the sound.Thst should at least get you to the general, if not specific, location.Sent from my SAMSUNG-SM-N910A using Tapatalk_Chip Bruce, RPhKansas City, MO2016 Impact 3122017 Silverado 3500HD SRW
09-08-2017, 09:14 PM 6
Senior MemberJoin Date: May 2016Location: Eastern Shore of MDPosts: 133 It is located behind the panel in the front storage compartment.It is on the curb side behind the water heater.if you remove the carpet covered panel (runs from front to back of rv) that attaches to the plastic panel in the convenience center you can get to it from there.
09-10-2017, 04:38 AM 7
Junior MemberJoin Date: Sep 2017Location: S LakePosts: 3 I put water in the fresh water tank and ran all the faucets and toilets.The pump ran steady when using all except for the shower.When turning on the shower it pulsed.I let it run for several minutes.Any ideas why only the shower pulses?Thanks
09-10-2017, 04:51 AM 8
Site TeamJoin Date: Mar 2011Location: GaylordPosts: 23,214 First, I’d suggest you remove the showerhead from the hose and see if it stops the “short cycling”.Chances are it will.If so, it’s the GPM of the flow restrictor in the showerhead that’s causing the pump to cycle.The shower causes the pump to cycle probably because of the “flow restrictor” in the showerhead.Depending on the amount of water flowing through the specific faucet, the pump will either deliver the volume by running all the time or if less water volume is required by the faucet in use, it will run to supply the pressure and then turn off until the pressure drops and the pump cycles to repressurize the system.You won’t “hurt your pump” by using it as it is, but if it “bothers you” you could consider installing an accumulator tank at the pump output.That will “buffer the pressure” and stop the “short cycling” caused by the flow restrictor in the showerhead.You might, if you’re using the OEM showerhead, consider changing it for an Oxygenics brand.They offer a different “spray pattern/droplet size” and the flow restrictor is a bit different so that may also reduce your “pump cycling”._John2015 F250 6.7l 4×42014 CougarX Lite 27RKS
10-29-2017, 05:36 PM 9
MemberJoin Date: Jan 2017Location: Mount HollyPosts: 39 pulsing tip.I found that if we didn’t switch from fill to normal at our convenience center it made our pump pulse abnormally too much.Sent from my SAMSUNG-SM-G891A using Tapatalk
Posting Rules
Youmay notpost new threadsYoumay notpost repliesYoumay notpost attachmentsYoumay notedit your posts


BB codeisOnSmiliesareOncode isOnHTML code isOff Forum Rules

DIY RV Water Pump Replacement in 12 Easy Steps

Replacement of your RV’s water pump is a relatively straightforward and affordable operation if the pump is beyond repair or if you simply wish to replace your old pump to a new one. You will be guided through the entire procedure step-by-step, from removing the old pump to installing the new one, by following this DIY instruction. So whether you’re an experienced RVer or a total novice, you’ll be able to do the task with ease! But first, let’s see whether you really do need to replace your water pump.

When Should I Replace My RV Water Pump?

When the water in your RV system stops flowing the way it should, it is most likely that your water pump has to be replaced. It is quite probable that your water pump has failed and that you will need to have it replaced if the water pump does not start when you open a faucet when you turn on the water supply.

Related:Why does my RV’s water pump keep running? This is what you should do! However, there are a variety of additional situations in which you might want to consider (or require) an RV water pump replacement, such as:

  • Pump that is leaking water from the housing or casing (and it isn’t merely a loose connection), it is probable that the pump has to be replaced. Pump that is leaking from the housing or casing The following are the actions to take if your RV’s water pump is leaking when it is connected to city water: Strange noises are coming from the pump: For your own piece of mind, you might choose to replace the water pump before embarking on a lengthy journey, rather than risk it failing while on the road. RV water pump replacement: Alternatively, you may just choose to upgrade to a more efficient or powerful model
  • Or

Whatever your reason for needing to repair your RV’s water pump, we’re here to help you through the process as smoothly as possible. Let’s get this party started!

RV Water Pump Replacement Step-By-Step

To begin the process of repairing your RV’s water pump, we’ll need a few equipment and materials, the most of which you’re probably already familiar with. In addition, you’ll want a new water pump to complete the job. Hurflo RV water pumps are highly recommended since they are undoubtedly the most popular water pump brand for RVs and travel trailers, have excellent customer reviews, and are quite affordable!

What You’ll Need

  • Drill or screwdriver, wire cutters with stripper and crimper, spade connectors, and a replacement RV water pump are all required. Water-catching bowl and towels (for catching and absorbing any spilt water)

We can begin installing the new RV water pump as soon as you have all of the necessary equipment.

How to Replace an RV Water Pump Video Guide

Credit: RV Geeks on YouTube for this video on how to replace an RV water pump – the best RV water pump replacement technique — an easy DIY project.

1) Turn Off the City Water Connection and Water Pump

First and foremost, we must disconnect the RV’s water supply from the city and switch off the water pump. The first thing you should do if you are working on the plumbing system in your RV is to drain the water supply.

2) Cut Power to the Pump

The next step is to turn off the water pump’s electricity. You have two options for completing this task:

  1. Remove the water pump fuse from your 12-volt electrical panel, if it is present. Disconnect the RV’s electricity and turn the battery disconnect switch to the off position to prevent energy from flowing to the pump.

Either approach will be effective.

3) Drain the Water From the System

Turn on a faucet in your RV and let it run until it is completely dry. This will remove the water from the system and bleed out any pressure that may have built up.

4) Disconnect Pump from Latching Controller (if Applicable)

If your RV has a latching controller, we will need to disconnect it from the pump before we can start working. What is a latching controller, and how does it work? By using this specific gadget, you may have a on and off switch for your water pump in numerous areas, such as the bathroom or the kitchen, for example. However, this is not always true. The latching controller is often situated close to where the pump is located. If you are unable to locate it, you may need to consult your owner’s handbook to determine its precise placement.

For a latching controller, look for a box with multiple cables that go into the different pump on/off switches on your RV’s electrical system.

To turn off the electricity to the latching controller, do the following:

  1. Remove the ground wire from the water pump and connect it to the latching controller (typically the black wire). Take the positive lead out of the latching controller and set it aside (usually a red wire which may also be connected to a yellow wire). If you have a yellow wire, you can cut it because we’ll be connecting it to the positive line on the new water pump
  2. Otherwise, leave it as is.

5) Remove Water Lines from Pump

Place a pail or basin beneath the pump before removing it, since water will most likely pour out of the pump. To prevent harming the plastic fittings, unscrew the lines with your hands rather than using a screwdriver.

6) Remove Pump From Mount

The pump may easily be unscrewed from its mounting bracket after the inlet and output hoses have been detached from the pump.

7) Move Filter From Old Pump to the New Pump

Following that, we’ll need to remove the inlet filter from the old water pump and replace it with one from the new one. The procedure is rather straightforward:

  1. Remove the filter by unscrewing it, twisting the two pieces of the filter together to open it, and cleaning it out. For really unclean or outdated surfaces, you may just replace it (see the replacement option further down this page). To reinstall the filter on the new pump, first screw the fitting from the new water pump into the filter. Then screw the filter back into place. It is necessary to mount the filter on the side of the water pump with an arrow pointing in the same direction. The arrows should be pointed in the same direction on both sides of the board. Remove the red shipping cap and screw in the fitting in the location where the shipping cap used to be. Then, to secure the fitting into the pump, slide the clip all the way down.

All that is left is to attach the fitting to the pump’s outlet side, which we will do next.

Remove the red shipping cap and screw the fitting into position, then slide the clip down to secure the fitting in place. Remove the red shipping cap and screw the fitting into place.

8) Strip and Connect Wiring for Latching Controller

Remove the wire insulation from the pump’s black ground wire tip, and then crimp on a spade connector to link the two wires together. Using your fingers, twist the exposed red and yellow wires together prior to crimping on a spade connection. Notably, the wiring in your recreational vehicle may change significantly depending on its brand and type. If this is the case, have a look at the photograph you took before you started. Remove the yellow wire from the new pump (which we clipped in the previous step) as well as the red wire from the old pump.

9) Mount the New Water Pump

After that, you may proceed to install the new pump in the same area as the old one. For the most part, the screw pattern for the replacement pump will be identical to that of the old pump. If this is the case, you may only need to drill fresh screw holes.

10) Connect Water Lines to the Pump

Attach the new pump’s input and output water lines by hand, taking care not to damage them.

11) Connect Pump to Latching Controller

Connect the positive lead (in the video above, this is represented by the red and yellow wires) to the latching controller if it is necessary. Then link the black ground wire to the rest of the system.

12) Test Pump and Check for Leaks

All that remains now is to ensure that everything functions correctly and that there are no leaks. To do so, connect the electricity to the pump and turn it on, then turn on the faucet. During the first priming of the RV water pump, you may observe some spitting from the faucet. This is just the escape of air from the wires. Once you realize that the water is flowing continuously from the pipes, you may turn off the faucet. How to Prime an RV Water Pump is a related article. Finally, check all of the connections at the pump for any signs of leakage.

That’s all there is to it!

RV Water Pump Replacement FAQs

If properly maintained, an RV water pump may endure for up to ten years in the field. Pump life may be prolonged by cleaning the filter on a regular basis, sterilizing the fresh water system after storing water for lengthy periods of time, and performing frequent leak checks.

How Do I Know if My Camper Water Pump Is Bad?

Water pump failure can be detected when the unit begins to produce excessive and odd noises, when it begins to leak from the pump itself, or when the unit ceases to function entirely.

How Much Does It Cost to Fix an RV Water Pump?

If you do it yourself, you can save more than $100 on the typical RV water pump replacement cost. This covers the cost of the pump as well as the cost of all of the necessary parts.

What Size Water Pump Do I Need for My RV?

Your typical RV will be equipped with a pump that produces between 3 and 3.5 gallons of water per minute, depending on the model (GPM). Pumps capable of pumping 5 gallons per minute or more are frequently seen in larger RVs. It is entirely up to you to make your decision. If you’re satisfied with the performance of your present pump, you may look out its GPM on the pump label or in the owner’s handbook and purchase a pump of a similar size to replace it. In the event that you wish to upgrade and the cost is within your budget, you can go with a higher GPM model.

Camper FAQs is made possible by donations from readers. It is possible that purchasing through links on our site will result in us receiving an affiliate commission. Because I am an Amazon Associate, I receive money when people make eligible purchases.

RV Water Pump Guide

Do you need to repair the water pump in your RV? We suggest the Shurflo 5030 for the vast majority of recreational vehicles since its widespread use speaks for itself. It has a maximum flow rate of 3 GPM with ports that are 1/2″ in size. The Shurflo 4300 is an excellent choice if you need to pump more gallons of water per minute. If you’re traveling “in the boonies,” where there is little to no water pressure, the Shurflo 2088 will not be damaged if you accidently run it dry by accident.

What is an RV Water Pump?

Fresh water pumps and macerator pumps are the two most common types of water pumps used in recreational vehicles. The fresh water pump in your RV is responsible for providing water pressure in your RV’s shower, toilet, and sinks. Macerator portable waste water pumps in an RV are used to grind down waste materials. A waste water pump from Flojet, model 18555-000A, is one of our most popular models. This post will concentrate on fresh water pumps for recreational vehicles.

What does an RV water pump do?

A RV water pump’s primary functions are to provide pressured water from your rig tank and to deliver a consistent volume of water per minute. Water is stored in built-in tanks in the base of recreational vehicles, which are positioned in the rear of the vehicle. An RV tank has a capacity of between 50 and 200 gallons of fresh water on average. The camper water pump draws water from the tank and lets you to use the water that has been drawn up from the tank by the pump. The majority of recreational vehicle pumps output 3.5 gallons of water per minute.

One of the most effective ways to gauge the strength of your pump is to count how many gallons of water it can pump in one minute.

The RV water pump is equipped with a switch that automatically turns it off once the desired pressure is reached.

Where do I find my RV water pump?

The quick answer is that it may be found in a variety of locations in an RV. Beneath sinks, under the bed, and in the kitchen are some of the most common hiding places we’ve discovered. In the kitchen, for example, the following is an illustration of a water pump positioned beneath shelves: Identifying your RV’s master control switch will help you identify it if you are unclear of its location. It will resemble something like this in appearance: This switch is labeled as a Water Pump switch. When you turn it on, you can hear it hum.

It is sometimes simple to trace the problem back to the position of the water pump.

Simply remove the cover with a screwdriver and you’ll be able to get to the pump easily. Because there is a pump hidden beneath this stove, you would need to remove the screws on either side of the rectangular panel in order to get access to it:

What pump do I need for my RV?

The following properties of a pump are recommended: 12V and 24V are the two most frequent voltages. Water pumps that operate on 12 volts are typical for RV and trailer use. RVs, campers, motorhomes, and trailers are all powered by 12V batteries, which are common in the industry. RV water pressure is significantly increased with 24 volt RV water pumps. The usage of these water pumps in large buses and vehicles is discouraged since they need more power and energy than 12 volt water pumps. The more power the pump has, the more energy it has; nevertheless, larger pumps are not necessarily superior in terms of energy production.

  1. Because 24 volt pumps contain such a large amount of power, they may create spikes in your water and electric costs.
  2. Consider the RV water pump’s noise and energy consumption as well, since these elements have an impact on the pump’s power.
  3. A jerky flow of water shows that there is insufficient water pressure in the system.
  4. Both the Shurflo water pump and the Flojet water pump are among the most popular Kleen-Rite products.
  5. Here are some of our most popular models: How can you safeguard your pump and ensure that it continues to operate at peak performance for many years to come now that you know our recommendations?

RV Water Pump Troubleshooting:

When it comes to troubleshooting, the most important thing to remember is to winterize your water system at the end of the season. This implies that you must completely drain all of the water from your water pipes. In addition, storing your RV pump for extended periods of time in hot summer conditions may diminish its life expectancy. In response to some of the most commonly requested problems, we reached out to RV owners and local RV shops for troubleshooting advice.

  • Question: How do I winterize my pump? Answer: According to Brian at Wagners Outdoor Express RV, the most common problem with RV fresh water pumps is the inability to properly winterize them. To winterize a pump, there are two basic methods: either by blowing air through the water lines or by putting antifreeze through the water lines. Brian recommended that you use antifreeze to keep your car from freezing. He has known people who have bypassed the antifreeze, but he has found that the air does not always reach all of the water droplets that have remained trapped. During the winter, any residual water will freeze and cause difficulties with the pump system. The leftover water droplets will be washed away if you put antifreeze through the system. Question: My RV’s water pump continues running
  • Answer: You may be experiencing low water pressure as a result of a worn or outdated pump diaphragm assembly, which may be found here. Consult the pump’s owner’s handbook to determine which model number is required for the diaphragm replacement procedure. You’ll also want to check to see that the fresh water tank has enough water in it. Even if the water supply runs out, the pump will not shut off. Is the water level at a dangerously low level? Because of the low water level in your RV’s fresh water tank, it is possible that the water pump is sucking in air rather than water. In order to allow air to escape and prime the pump, fill the tank with water and open the faucet. When I switch on my RV’s water pump, nothing happens. Is there something wrong with the battery? If so, you may need to replace the pump. Check to confirm that your water pump switches are turned on, and that your RV fuse panel’s breakers are turned on as well. The RV water pump is operational, but no water is being discharged. The solution: Check the water pipes coming into and out of the pump. Take note of any blocked or kinked lines, as well as any symptoms of leakage. Obtain some towels and arrange them around the pump to prevent a sloppy mess from forming. Check to see if water is flowing to the pump: If you gently release the water hose and the line is dry, the problem is most likely with the water line from the tank, which may be found here. Fill the water line with water and check to see whether the faucets work after that. If you are still not seeing water, it is possible that there is an issue with the pump. Check to check whether any water is flowing out of the pump by turning it on. If you observe that water is simply leaking from the pump, you should consider replacing the pump.

How Do I Replace and Install My Pump?

Keep watching to witness Kleen-Rite Senior Technician Tom Allen reassemble a Flojet water pump in our video! It is important to note that many individuals choose to purchase a completely new pump rather than replacing individual parts for the following reasons:

  • Pumps that are completely new are not prohibitively costly. It requires time and knowledge to replace specific components.

When it’s time to replace the pump, follow these steps to ensure a successful installation:

  1. Turn off all of the water pump switches in your recreational vehicle. Turn off the water supply to your home. Drain as much water as you can by turning on the faucet and allowing it to flow for several minutes. Disconnect the electrical cables from the power source. There will be two lines: one for power and one for ground. The colors will be red and black. It is possible that the wires will extend inside the electrical pressure switch. Removing the screws that keep the pump in place is the next step. Unscrewing the remaining lines is the next step. It’s possible that there will be some last water leaks here, so have towels on hand. Remove the pump from the immediate vicinity

After that, install the replacement pump as follows:

  1. Reinstall the pump and reconnect the water pipes if necessary. Place it in the same location as the previous pump and screw it into place using a screwdriver
  2. Read the directions in the new pump’s instruction booklet. There is a set of installation instructions specific to each pump. Turn on a water faucet if necessary. Because the RV is still filling the pipes with water before it reaches the faucet, it may take several seconds for the water to start flowing. To test for leaks, fill the water tank halfway with water, switch on the pump, and look for any leaks coming out of the water lines.

Following the installation and operation of your RV water pump, some typical parts and accessories include:

  • Prevents the water pump’s water pressure from cycling on and off
  • Keeps the water flowing in one direction. Increases water flow while also preventing water from seeping back into the pump.
  • It is important to have a reliable RV water pump strainer to keep debris out of the pump. Installing an inline strainer on the pump is an optional modification that may be performed. If you don’t use one, the pump will still work, but you run the danger of debris getting into the pump and blocking it or causing it to fail.
  • Pressure spikes are reduced by using a water pump accumulator tank. This prevents the pump from turning on and off as frequently. It is a separate item that is approximately the same size as the pump and is installed adjacent to the pump
  • And Aids in the reduction of vibrations and noise

Water Pump Location – Thor Forums

02-13-2021, 09:04 PM 1
Junior MemberBrand: Thor Motor CoachModel: Thor Vegas 25.2State: DelawarePosts: 2THOR7649 Water Pump Location


Good AfternoonI own a 2017 THOR Vegas 25.2, can anyone tell me were the water pump is located?_

02-13-2021, 09:10 PM 2
MemberBrand: Thor Motor CoachModel: Quantum rw28State: LouisianaPosts: 32THOR22150 My 2018 Thor Quantum rw28 has the fresh water tank and pump assy. under the bed.You have to lift up the mattress and there is a hinged door. Lift that up and you will find the tank and associated plumbing/wiring/pump. Not sure if both MH’s are the same but probably not far offI hope that helps_
02-13-2021, 09:35 PM 3
Senior MemberBrand: Thor Motor CoachModel: FW Hurricane 33TState: EnglandPosts: 813THOR16471 Quote:Originally Posted byglazzaro9@gmail.comGood AfternoonI own a 2017 THOR Vegas 25.2, can anyone tell me were the water pump is located?Welcome to “The Show!” Can you not follow the sound when the pump is running? It should be right there._
02-13-2021, 10:21 PM 4
I Think We’re Lost!Brand: Still LookingModel: Tiffin Wayfarer 24 BWState: New YorkPosts: 21,911THOR8860 Turn it on, and open up a faucets.You’ll have no trouble following the sound.Good luck, and welcome to the forum!_
02-13-2021, 11:36 PM 5
Junior MemberBrand: Thor Motor CoachModel: Thor Vegas 25.2State: DelawarePosts: 2THOR7649 The pump stopped working, trying to locate so I can replace_
02-13-2021, 11:53 PM 6
Senior MemberBrand: Thor Motor CoachModel: Hurricane 29MState: New YorkPosts: 150THOR5875 Quote:Originally Posted byglazzaro9@gmail.comThe pump stopped working, trying to locate so I can replaceIf I recall correctly, in our 2017 25.2 the pump was under the jack knife sofa next to the fresh water tank._
02-13-2021, 11:56 PM 7
Senior MemberBrand: KeystoneModel: SprinterState: FloridaPosts: 1,422THOR15553 Quote:Originally Posted byglazzaro9@gmail.comThe pump stopped working, trying to locate so I can replacecheck the fuse at the pump before you replace it. Use a voltmeter and be sure you have voltage._2011 Keystone Sprinter 323BHS.Retired Master Electrician.All Motor Homes are RV’s. All RV’s are not Motor Homes.
02-14-2021, 12:00 AM 8
Senior MemberBrand: Thor Motor CoachModel: 2016 Hurricane 27KState: FloridaPosts: 2,531THOR1589 Welcome to the forum!Yes, it is under the jackknife sofa. Close to the bathroom wall. Wondering why the question, is there a problem? BTW, there is some room under that sofa to store a few things._May the trails always twist in your favorMay the tales always end in good lightMay you have more friends than one campfire can hold
02-14-2021, 01:44 PM 9
Senior MemberBrand: Thor Motor CoachModel: FW Hurricane 33TState: EnglandPosts: 813THOR16471 Quote:Originally Posted byglazzaro9@gmail.comThe pump stopped working, trying to locate so I can replaceAhhh.!A little more info and it makes more sense. I think the others have located it for you, so good luck!BTW, if it had worked before, were you not at all curious with “What is that noise?” whenever you turned on a faucet?_
06-03-2021, 10:58 PM 10
Junior MemberBrand: Thor Motor CoachState: FloridaPosts: 7THOR12004 I own the 2017 Thor Vegas 25.3 and I am wondering where the water pump is located?_
06-04-2021, 12:07 AM 11
OldWEBSenior MemberBrand: Thor Motor CoachModel: FW Hurricane 33TState: EnglandPosts: 813THOR16471 Quote:Originally Posted byTpowers@tampabay.rr.comI own the 2017 Thor Vegas 25.3 and I am wondering where the water pump is located?It was mentioned this is a 25.3.

Posting Rules
Youmay notpost new threadsYoumay notpost repliesYoumay notpost attachmentsYoumay notedit your posts


BB codeisOnSmiliesareOncode isOnHTML code isOffTrackbacksareOff PingbacksareOff RefbacksareOff


Forum Rules

Leave a Reply

Your email address will not be published.