What To Set Water Heater To - ERNIEGRAVES | Process Measurement & Control

What’s The Best Water Heater Temperature Setting?

A hot shower may receive a bad name from your dermatologist since it might dry up your skin, but many people like it for its relaxing properties! In a household where hot water is fiercely competed for among family members, or even between your washing machine and dishwasher, you may be tempted to raise the temperature of your hot water heater. But at what point does it become too hot? There are differences of opinion between the Department of Energy and the industry. Scalding can occur at temperatures below 120 degrees Fahrenheit, although 140 degrees Fahrenheit is the normal default temperature.

Whatever temperature setting you choose, it’s vital to remember that the kind of pipe used, how the water is heated (gas or electric), and whether your system is tanked or tankless have no effect on the temperature you choose.

Use 120°F if you have small children or the elderly in your house who are prone to third-degree burns in seconds, or if you are the sole inhabitant of your home since there is less demand for hot water. Consider 140°F if you have an immunocompromised individual in your house, a dishwasher that does not pre-heat, or if you have a large number of occupants owing to the increased need for hot water.

But what about the expenses of energy? We get what you’re saying! Water heaters account for around 14-18 percent of the total energy consumed by a residence on a typical day. Furthermore, it may be tempting to lower the temperature in order to save money. It should be noted that a 10°F decrease in temperature is related with a 3-5 percent reduction in energy use. Legionella, on the other hand, can live at temperatures as high as 122°F. So make sure to strike a balance between your risk tolerance and your energy consumption targets!

Many hot water heaters are equipped with a temperature control dial.
Start with 120°F and gradually increase the temperature in small increments until you get your desired result.
A water tank booster may be an appropriate option in houses where the requirement to maintain a greater hot water temperature for health safety must be balanced with the need to reduce the danger of scorching.
Alternatively, you could live in a house where, no matter what temperature you select, hot water takes an inordinate amount of time to reach the faucet (or a certain tap farthest from the hot water heater).
Whatever you choose, we’re only a phone call away if you’re having issues with your hot water!

What Temperature Should I Set My Water Heater At?

Get in Touch With Us

Setting the Ideal Hot Water Heater Temperature

Are you tired of burning your hands every time you turn on the hot water in the shower? What if you’re having trouble getting a comfortable water temperature, no matter how high you turn the faucet up? These are not always indications that your water heater is malfunctioning, but rather that the temperature setting you have chosen is not optimal for your purposes. A water heater that has been installed incorrectly can have a significant influence on your life, even in areas that are not directly linked to your plumbing or heating system.

It can also have a negative influence on your health or the health of people who share your home with you.

A definitive or simple response cannot be given; rather, part of it is a matter of personal choice.

General Recommended Water Heater Temperature

You can find out what temperature water should be at by visiting the Environmental Protection Agency. The optimum water temperature is 120 degrees Fahrenheit. You will really save money because your water will not be hot enough to cause scalding, most small households will have adequate hot water for their needs, and reheating will not need an excessive amount of energy consumption, allowing you to save money on your utility bills. This temperature, on the other hand, is not ideal for everyone.

Considerations When Choosing a Water Heater Temperature Setting

Do you have any at-risk individuals residing in your home? Those who are particularly sensitive to high temperatures may suffer serious consequences if they are exposed to overly hot water. Water at 150 degrees Fahrenheit may cause third-degree burns in newborn babies in only two seconds, while water at 140 degrees can cause third-degree burns in babies in just five seconds. Temperature reduction is more safer for your infant and far more cost-effective in terms of energy use. A water heater set at no more than 130 degrees is recommended if you have a baby or any youngster under the age of three in your household.

Those who have compromised immune systems or who suffer from respiratory ailments, on the other hand, may benefit from a hotter water temperature in order to destroy bacteria while also increasing the concentration of steam in the air when bathing.
Do you have an appliance that is energy efficient?
Essentially, these systems take in water and then raise the temperature to even higher levels to provide an even better and more hygienic clean, all without the need for you to raise the temperature coming from your water heater.
If, on the other hand, it won’t be for a long time, you may wish to raise the temperature of your water heater to 140 degrees.
How many people do you have living in your house?
Those who like a hotter shower increase the ratio of hot to cold water in their shower.
The temperature of the water that comes out of your water heater, on the other hand, will have an impact on this as well.
People that use cooler water heaters will require more hot water and less cold water in order to achieve their goals.
If you have a large home with multiple people living in it, you should raise the temperature of the water to ensure that your hot water supply lasts as long as possible.

Do you require assistance with your water heater in the Los Angeles area? Whether you want a thermostat replacement or the installation of a new water heater, contact the professionals at Moe Plumbing Services at (818) 396-8002 now.

What Temperature Should a Hot Water Heater Be Set At?

Previous PostNext PostYour water heater accounts for around 18 percent of the energy consumed by your house. If the temperature of your water heater is set too high, you will be forced to pay the price in your monthly energy bill. The converse is true: if you have your water heater set too low, your water may not get hot enough (resulting in short showers), or worse, it may get contaminated with germs. Maintain a 120-degree temperature for your water heater at all times because infections can form in the stagnant water within the water heater, notably Legionella, which is extremely deadly.

In addition to being hot enough to keep viruses at away while not being scorching hot enough to cause blistering, 120 degrees will provide adequate hot water for most small households while still being relatively energy-efficient, according to the Environmental Protection Agency.

Factors That Affect Hot Water Temperature Setting

These criteria are unaffected by the kind of piping you have (PEX, PVC, or copper), the method of heating the water (gas or electric), or even if you have a tankless hot water heater installed.

Owners of dishwashers that do not pre-heat the water may wish to set their water heater temperature to 140 degrees
Elderly or families with young children may want to keep the temperature at 120 degrees. BabyCenter.com states that “it takes just two seconds for a kid to acquire third-degree burns from water that is 150 degrees and five seconds if the water is 140 degrees, the temperatures at which hot water heaters frequently leave the manufacturer.” It is recommended that the hot water temperature be maintained at 140 degrees in homes with people who have a compromised immune system or respiratory problems. Because there is less demand for hot water and hence less money spent on hot water, many people who live alone prefer a lower temperature within an acceptable range. The temperature of the water tank is often set higher in big households, in order to support the increased demand for hot water
Nevertheless, if you want to save money, every 10 degrees you lower the temperature of the water tank thermometer, you save 3 to 5 percent on your energy bill.

Are you still undecided? To begin, set the temperature to 120 degrees Fahrenheit and gradually raise it in small increments until you reach the desired shower temperature.

What’s Your Current Temperature Setting?

Check the temperature setting on the water heater (if one is available) or take a temperature reading from the faucet to determine what it is currently. After turning on the hot water faucet, allow it to run for a few minutes before getting the temperature reading.

Solutions to Common Hot Water Tank Problems

If you’re concerned about pathogens in your hot water, as well as the possibility of scalding water, you might consider installing a hot water tank booster. This allows you to maintain your water at 140 degrees in the tank while mixing it with cold water to bring the temperature down to 120 degrees before it reaches the faucet. Having a hot water circulating system installed in your home might alleviate the problem of waiting for hot water to reach the faucet in a large household. This method circulates hot water slowly through the pipes in order to prevent it from cooling down before it reaches the faucet.

Professional Plumbing Services

It’s possible that your hot water isn’t hot enough no matter what setting your water heater is set to. If you need assistance adjusting your hot water heater or troubleshooting any difficulties, call your local Mr. Rooter Plumbing at (855) 982-2028 or submit a request for a free estimate on our website. Not only does your hot water need to be “just perfect,” but so does everything else in your home. Aire Serv, a neighborly firm, can assist you in determining the optimal air temperature. Previous PostNext Post Previous Post

What Is The BEST Water Heater Temperature Setting?

Please keep in mind that this content may contain affiliate links. This means that, at no additional cost to you, we may gain a small profit on purchases made via our links.

If you have already set the temperature and are thinking to yourself, “I don’t have any hot water,” or “I don’t have enough hot water,” there are a few variables that might be causing the problem. If all else fails, it’s possible that the heating element is faulty and has to be replaced.

How To Check Your Water Heater Temperature

The majority of water heaters do not have a temperature gauge with a digital readout on them. Temperatures or heating ranges are marked on thethermostat, rather than numbers. A cup and a culinary thermometer will be required in order to correctly determine the temperature of the hot water heater. If you haven’t used your water heater in at least one hour, turn on the faucet that is nearest to it. Allow the water to run for at least one minute to ensure that the water is at its warmest possible temperature before filling the cup with it.

Recommended Temperature Settings

Water heaters are pre-programmed to operate at OSHA-recommended temperatures, which are around 140 degrees. The Environmental Protection Agency, on the other hand, recommends lowering the thermostat down to 120 degrees Fahrenheit to save power use and using a booster heater to attain sanitizing temperatures at certain outlets. Another point of view is that lower temperatures are preferable for homes with little children, although higher temperatures are more effective in cleaning and sanitizing surfaces.

However, the temperature is low enough to avoid scorching while being high enough to destroy hazardous microorganisms.

How To Turn Up Your Water Heater

If you are dissatisfied with the suggested temperature of your hot water heater, you may alter the settings to receive extra hot water. Although electric water heaters may require a screwdriver and potentially a tiny wrench or socket, most hot water heater settings are straightforward to modify. Keep in mind that the thermostat is factory configured to a recommended temperature, and that altering the setting may increase the risk of significant burns from the appliance.

How to Set Temperature on a Gas Water Heater

The temperature of a gas water heater may be adjusted by turning the setting knob on the water heater. The majority of gas control valves have a knob with different designations on them, such as A-B-C. Control valves for gas water heaters may be labeled differently depending on the manufacturer. In the majority of circumstances, the following is what each label indicates:

Warm = 80-90°
Low = 80-90°
Hot (or triangle symbol) = 120°
A= 130°
B= 140°
C= 150°
Very Hot = 160°
High = 120°

There is a “Vacation” setting that appears from time to time. This does not heat the water, but it does ensure that the pilot light remains lit.

How to Set Temperature on an Electric Water Heater

Turn off the circuit breaker if necessary. Remove the access panels from the room. Under the insulation, look for the thermostat adjustment screwhole. Adjust the thermostat control to the appropriate temperature by using a straight screwdriver to make the adjustment. After replacing the insulation and panels, the power should be restored. Here’s a good video that demonstrates the procedure:

Factors That Affect Water Temperature

Some of the things that may influence the temperature of your hot water include the distance between the water heater and the outlet, the way the pipes are built, and the quality of the heating element itself, among others. Because of the length of the pipe and the small bore size, it will take longer for the hot water to reach the opening. Additionally, pipes that run beneath or outside the residence may be exposed to freezing or freezing temperatures in the winter and summer. Installing a hot water recirculation system in a large house may be worth considering since it can reduce the amount of time it takes to heat water in all of the property’s outlets while also resulting in significant cost savings over the long term.

If setting the thermostat does not result in the desired temperature, it is possible that the water heater element has to be replaced. If you don’t notice a difference in the water temperature after adjusting the thermostat, it’s likely that the thermostat is broken and has to be replaced.

How to Set How Water Heater Temperature by Thermostat

You might be wondering how to adjust the temperature of your hot water heater. In this section, you will learn all you need to know about your gas or electric water heater thermostat, including how to adjust your hot water heater temperature thermostat and what temperature is optimum for hot water.

What’s the Right Temperature for a Hot Water Heater?

It’s an often asked question: what is the optimal temperature for hot water? Setting a tank-based hot water heater to 120 degrees Fahrenheit is recommended by the United States Department of Energy. If you have never changed the temperature of your hot water heater, it is most likely set to the 140-degree Fahrenheit level that is recommended by most manufacturers of hot water heaters. What is the significance of adhering to this temperature standard? If the temperature setting on the water heater thermostat is set too high, the water will be excessively hot and might cause burning or scorching.

How to Set Your Hot Water Heater Temperature Thermostat Setting

Before you make any modifications to the temperature thermostat setting on your hot water heater, you should first ascertain what the current temperature is set at so that you can establish how much you need to alter the settings. A conventional cooking thermometer may be used to quickly and accurately detect the temperature. You should calibrate your thermometer once you have determined the current temperature setting. Fill a cup halfway with cold water and submerge your thermometer until the temperature dial reaches 32 degrees, or the lowest temperature displayed on your thermometer’s gauge, and then remove it.

Meanwhile, locate the faucet that is closest to the water heater and turn it on until it is hot (while you are calibrating your thermometer).

If your thermostat is set too high, the temperature may be high enough to burn you.

Adjusting aGasHot Water Heater Temperature Thermostat Setting

The majority of gas water heaters are straightforward due to the presence of a clearly readable dial at the bottom of the tank’s bottom section. If you follow the methods outlined below, it is simple and straightforward to alter this dial.

First, adjust the temperature by turning the knob to the hotter or cooler position, depending on the situation. After that, let it sit for a few hours (around three or four) and then check the temperature again. If the temperature is still incorrect, make another adjustment and repeat the process until the problem is resolved. Do you require assistance? Call Hackler Plumbing for a free estimate. If you want the services of aMcKinney plumber, we can assist you

Adjusting anElectricHot Water Heater Temperature Thermostat Setting

The process of adjusting the temperature thermostat setting on an electric hot water heater is a little more difficult, but still pretty simple. The vast majority of electric water heaters are equipped with two thermostats: an upper and a lower thermostat, both of which are placed beneath two control panels. Setting both thermostats to the same temperature can help to guarantee that your electric water heater operates as effectively as possible. One thing to keep in mind is that some tiny electric hot water heaters only have one thermostat.

Here’s how to adjust the temperature on your electric hot water heater thermostat:

Please keep in mind that you will want a screwdriver to execute the following procedures in order to alter the temperature of your water heater.

Make sure your water heater is off by turning off the electricity. This may be accomplished by locating your circuit breaker and shutting off the electricity in the area surrounding your water heater
Then, locate the thermostat(s) on your water heater and turn them on. Typically, they are located behind a control panel that is secured with screws. Remove the cover from the access panel using your screwdriver (s). To access the thermostat, you may need to remove the insulation from your heater if it is properly insulated. The thermostats will be controlled by a dial, and the dials will have a varying reading depending on the manufacturer of the heater. Once the control panel has been removed, you may change the temperature knobs to make the room hotter or colder according on your preferences in terms of temperature. Take care to set both thermostats to the same temperature setting if you have more than one. Replace the control panel covers and the screws with your screwdriver after they have been removed. After that, re-energize your water heater’s electrical system. After many hours, check the temperature of your hot water (about three to four). Continue to follow the above instructions until the water temperature reaches the required setting
If it still does not, repeat them until the temperature reaches the ideal setting for your needs.

Other Considerations: Water Heater Thermostat Setting Safety

There is one thing you should be aware of: your water heater is fitted with something known as a temperature and pressure relief valve, abbreviated “T P valve.” These can become worn out over time, and one sign that they should be replaced is the presence of water leaking through. This is a very crucial safety feature. If your unit is old, or if your hot water heater pressure relief valve is leaking after it has been replaced, get it examined by a competent plumbing professional.

Risks Of Too High Or Too Low Water Heater Temperature

You might be wondering what temperature to put your water heater to. When you purchase a water heater unit, the temperature is typically set by the manufacturer. However, this does not rule out the possibility of having some control over its temperature. The good news is that you may set the temperature to a level that is comfortable for you while yet ensuring the safety of your family. Previous to this, we wrote an article in which we spoke about how the heat in your shower might suddenly vary.

The temperature of the device is important since it can have an impact on how well it performs.

Top Risks of setting your unit temperature too high

An skilled plumber would advise against raising the temperature of your unit over the recommended level since it might endanger the safety of your children. It can also have an impact on your utility costs and the heater itself. In order to assist you, we have listed the following risks:

1. Scalding Accidents

Setting the temperature too high might result in scorching mishaps that result in burn injuries. According to the findings of a study on water heater temperature and attributes, many water heaters are frequently set at dangerously high temperatures. Several studies by the Centers for Disease Control and Prevention (CDC) have discovered that scald burns are the most common cause of injury in younger children. Every day, over 300 children between the ages of 0 and 19 are treated in emergency departments for burn-related injuries, with two of these children dying as a result of their injuries.

Accidents such as this may be prevented by allowing your water to flow for three minutes and then monitoring the temperature with a candy thermometer thereafter.

2. High electricity bill

Warning: Using a water heater with the temperature set too high will cause your energy cost to rise! According to the Department of Energy, standby heat losses from your water heater can cost you anywhere from $36 to $61 per year in energy savings.

The good news is that by lowering your thermostat, you may save anywhere from 4 percent to 22 percent on your annual energy expenditure. Lowering the temperature of your water heater can help to decrease standby heat loss, which is one of the reasons you have a high energy cost.

3. Lowers your unit’s service life

According to some sources, hot water can accelerate the accumulation of hard water mineral silt, particularly calcium carbonate, in the tank’s interior. It is possible that the buildup would cause corrosion in the water heater tank, which will result in a reduction in the estimated lifespan of the complete device. Leaks and polluted water might occur as a result of the rust accumulation in the storage tank. Another major reason for water heater failure is the deposit of rust on the interior of the heater.

We wrote an essay about why it’s important and how you can extend its lifespan.

Risk of setting your unit temperature too low

If you want to save money on energy costs, you should avoid setting the temperature of your unit too low. It is possible that you will have a health problem as a result.

1. Legionnaires disease

Every year, around 100 people in the United States are sent to hospitals due to a form of bacterial illness that can be caused by water heaters. The infections connected with the bacterium were responsible for up to 12 percent of the country’s death rates. Specifically, the Legionella bacteria are responsible for this particular kind of atypical pneumonia. It is common to find this bacterium in water at low temperatures — often between 20 and 45 degrees Celsius. You can contract the disease if you inhale small water droplets in the air that contain germs that cause it.

Evidence indicates that the majority of the bacteria’s spread occurred through the provision of drinking water in private residences.

It has been shown that the danger of contamination is significantly reduced when water heaters are set at 60°C or 140°F.

Ideal Temperature For Your Water Heater

The optimum temperature is. What several agencies have to say about the optimal temperature is summarized below: According to the Occupational Safety and Health Administration (OSHA) and the World Health Organization (WHO), water heaters kept below 60 degrees Celsius (140 degrees Fahrenheit) may promote Legionella development. This temperature, on the other hand, will almost certainly increase the likelihood of being burned by searing hot water. If you have young children at home, the Centers for Disease Control and Prevention (CDC) and the Energy Department recommend that you set your water heater’s thermostat to 120°F or lower.

This will help you keep control over the water temperature throughout your home, preventing it from being overly hot.

So, is it 120°F or 140°F?

We recommend keeping the temperature between 120 and 140 degrees Fahrenheit. However, you may regulate the temperature of your water heater between 130 and 140 degrees Fahrenheit, which is very useful for large water heaters used in hospitals and industrial settings.

In case you have little children at home, set the temperature to 120°F, which is considered safe by the majority of the population.

Your installer can help you adjust your water heater temperature.

As part of our service, our qualified specialist at SPS Plumber can assist you with setting the temperature of your water heater to the proper setting. In addition, we can do annual water heater maintenance on your unit. To schedule an appointment, please call us at 408-622-8183 (South Bay Area) or 209-597-9107 (Central Valley) right away!

How to adjust your water heater temperature

No one enjoys taking a cold shower. It’s much worse when you are scalded when the hot water is turned on. It is critical to correctly regulate the temperature on your water heater, not only for your health and safety, but also to save money on your power bill. Here’s how to regulate the temperature of your water heater to save money while also protecting your skin from sun damage.

The correct temperature range

It is recommended that your water heater be set within a specified temperature range for a variety of different reasons. A low temperature setting not only results in hot water that is merely lukewarm at best, but it can also promote bacterial development, which can lead to illnesses such as Legionnaires’ disease. This may be avoided by adjusting the temperature of the water heater to a level at which the bacteria Legionella cannot survive. A temperature of at least 140 degrees Fahrenheit (60 degrees Celsius) for water heaters is recommended by the Occupational Safety and Health Administration (OSHA) to prevent Legionella and other germs from growing in the water.

The time it takes for third-degree burns to occur at 150 degrees Fahrenheit (66 degrees Celsius) is less than two seconds.
Not to mention that a water heater that is set too hot might result in an excessively expensive power bill.
The greater the distance between a faucet and the water heater, the greater the amount of heat that will be lost as the water flows, especially if the pipes are not insulated.
When determining the appropriate temperature for your family and household, use your best judgment.
Make an adjustment, test it, and continue the process until you’ve found the ideal temperature setting for your house and water heater, which may take many attempts.
1:00

Adjusting water heater temperature

The interface used to control the temperature of a water heater will differ depending on the kind and model. Fortunately, the majority of water heater models can be modified in the same way. For example, most contemporary gas and electric water heaters are equipped with a thermostat concealed behind an insulated access panel. Electric water heaters are frequently equipped with two thermostats: one at the top of the tank and another at the bottom. Furthermore, most tankless water heaters include a display with a temperature reading as well as controls for altering the water heater’s temperature.

Turn on the water in the bathroom or kitchen sink and let it to run until the water is completely hot before using. Then, to get an accurate reading, place a thermometer beneath the surface of the water.

Tankless

The process of adjusting a tankless water heater is quite similar to the process of adjusting your air conditioning thermostat. Adjust the temperature by using the digital control panel, which may be adjusted up or down as desired.

Gas or electric water heaters

Some gas water heaters include a dial towards the bottom of the device that may be adjusted simply by turning it – no tools are required for this operation. Nonetheless, most current tank water heaters (whether gas or electric) require a bit more effort, but the process is still straightforward and should only take a few minutes.

Turning off the water heater’s electricity at the circuit breaker is the first step. To remove a thermostat(s), locate the access panel for the thermostat(s) and remove it using a screwdriver
Remove the insulation by peeling it back. To adjust the thermostat, use a flathead screwdriver to turn it up or down.

If your water heater has two thermostats, make sure they are both set to the same temperature. The temperature on the top thermostat should be a few degrees higher than on the bottom thermostat.

Replace the insulation and re-install the access panel, if necessary. Reconnect the water heater’s power supply
It is possible that you may need to relight the pilot light on a gas water heater.

Once you’ve made the necessary adjustments, you should wait at least three hours before checking the water temperature once more. It is possible that you may need to make more modifications in order to get the desired temperature. If you’ve increased the temperature and are still getting chilly showers, it’s possible that your hot water heater has to be serviced or completely replaced. Is the energy efficiency of your home high? Here are five different methods to find out. CNET’s Guide to Smart Livingis a one-stop shop for tips, techniques, and how-to guides that can help you live a more intelligent life.

Adjusting Your Water Heater Settings: How To Maximize Efficiency

Not many people are aware that selecting the proper water heater settings may result in substantial savings. Indeed, while the majority of people don’t give their hot water heater settings a second thought, they are actually highly critical in many situations. Not only will it save you money, but it will also make your showering experience more pleasant as a result of it. Here is a breakdown of the procedures.

Default Hot Water Heater Settings Can Vary

Temperature settings on water heaters in Phoenix are frequently set to as high as 140 degrees Fahrenheit as the usual setting. That is far greater than the majority of individuals require, although manufacturers do so for a variety of reasons. The Department of Energy states that germs cannot thrive in water that is so hot, among other reasons. Increased gas or electric water heater settings can be beneficial for people who have weakened immune systems or respiratory illnesses. In addition to impressing consumers who have presumably recently replaced their tank since the previous one had ceased performing correctly, high temperatures can also be beneficial.

How Much Are Your Gas and Electric Hot Water Heater Temperature Settings Costing You?

As a general rule, every 20 degrees you reduce the temperature of your gas or electric water heater, you may expect to save as much as ten percent on your utility bill. That’s not too shabby after all! In reality, it adds up over time, and you can almost certainly come up with a number of better uses for the money you save. “But hold on a minute,” you may be thinking. “I really enjoy taking hot baths!” However, you almost probably do not take showers above 140 degrees Fahrenheit, which can cause scorching because of the high temperature.

It’s conceivable that you won’t even notice a difference. No matter what happens, raising the temperature is a simple process. It has the potential to cause aging hotwater heaters to stop functioning.

How To Adjust Your Gas and Electric Hot Water Heater Temperature Settings

Now that you understand why you should reduce the temperature of your water heater, let’s look at how to go about doing so.

Step One: Get An Accurate Temperature Reading

It’s likely that the thermostat dial linked to your water heater tank is not functioning properly. As a result, you should really use a thermometer to monitor the temperature of the water flowing out of your faucet. The Department of Energy suggests that you measure the amount of water that is flowing out of the faucet that is the furthest away from your water heating system. Make a note of the settings after you’ve found them.

Step Two: Figure Out Where to Make the Adjustment

There are several distinct types of water heaters, and we’ll go through each of them separately.

Electric Water Heater Settings

In the case of an electric water heater, you must modify the hot water settings at the top and bottom of the unit. Both controls, which are often concealed behind a panel and consist of knobs that you crank to establish the appropriate electric water heater thermostat settings, are typically located on the same side of the panel.

Gas Water Heater Settings

Newer gas water heaters are equipped with temperature controls that are similar to those described above in the section on electric water heaters. Most gas heaters, especially older models, feature a temperature knob near the base that may be easily adjusted to the appropriate temperature.

Tankless Water Heater Settings

Finally, tankless water heaters are available. This is likely the simplest modification to make because most thermostats include an LED screen that allows you to directly control the thermostat’s temperature. In addition to being convenient, these systems frequently allow you to modify the tankless water heater settings more accurately than you could with traditional dial-based adjustment methods.

Step Three: Make The Adjustments

If you have an electric unit, make sure to turn off the electricity to it before modifying the hot water heater settings at the top and bottom, as we previously discussed in detail. This may be accomplished simply turning off the necessary settings on your circuit breaker panel. Doing so is also recommended in the case of a gas water heater that consumes some power (as some newer units do). But hold on a minute! What temperature should you choose as a starting point? The Department of Energy suggests that you set your heater to 120 degrees Fahrenheit for the best performance.

Some water heater temperature controls now include buttons that read “A-B-C” instead of numbers, which makes them easier to use.

To double-check these settings, consult the owner’s handbook for your water heater.

Step Four: Tweak the Settings as Necessary

After you’ve made the necessary adjustments to your gas or electric water heater thermostat settings, you may discover that you need to make a few more adjustments to get the best setting.

You’re trying to strike the perfect balance between comfort and cost-effectiveness. If that’s more than 120 degrees Fahrenheit for you, there’s nothing wrong with that. Make the necessary adjustments!

Frequently Asked Questions

It is nearly guaranteed that a temperature setting of 150 degrees will be too hot for your water heater. The likelihood of experiencing scalding is quite high at that temperature. You should be concerned about your youngsters, who may experiment with the temperature settings on the faucets while completely unconscious of the risk and end up scorching themselves.

What Is The Maximum Temperature For A Water Heater?

The highest temperature setting for the majority of water heaters is 150 degrees Fahrenheit.

Is 140 Too Hot For A Water Heater?

Yes, temperatures above 140 degrees Fahrenheit are uncomfortable for the majority of people. The only exception would be persons who require an additional layer of protection against germs, which cannot thrive in water at that temperature. However, because such a state does not protect you from scorching, you will almost certainly need to install an equipment at the showerhead that cools the water before it is discharged from the showerhead.

Why Is My Water So Hot?

If you haven’t changed the settings on your hot water heater in a long time, they are most likely still set to the factory default of 140 degrees. The latter is especially true if your hot water heater was only recently installed; the old one was almost certainly altered at some time over the years, whereas the new one is set to the manufacturer’s recommended settings.

What Temperature Should I Set for My Water Heater?

adminon posted a new comment 5:33:44 a.m. on May 25, 2017 It is possible to set a maximum temperature on your home’s water heater, which governs how hot the water coming out of your faucets may be at any one moment. While most of us don’t consider this to be a modifiable setting, it is in fact something that you can modify if you so want. A new water heater is usually set to a maximum temperature of 140 degrees Fahrenheit when it is first installed. Some believe that is the optimal temperature, while others believe that it is preferable to lower the maximum temperature to 120 degrees.

Here is a deeper look at what they are:

The argument for 120 degrees

As recommended by the United States Department of Energy and the American Society of Sanitary Engineering, the best temperature to set for a hot water heater should be 120 degrees Fahrenheit. The following are some advantages:

It is more beneficial to the environment. Not only does it need electrical or gas energy to heat your water, but it also takes energy to keep the water in the storage tank at that temperature (so you have hot water on demand). By lowering the temperature by 20 degrees, you may dramatically reduce the amount of energy consumed, resulting in significant savings. The energy savings are beneficial not just to the environment, but also to your money, with the potential to save you up to $60 per year. It also helps to avoid mineral accumulation. Using cooler water means that minerals are less likely to be deposited in your pipes, reducing the troubles caused by hard water and keeping your water flow unimpeded
It also helps to prevent severe scalding. This is, without a doubt, the most compelling of the arguments. Water that is 140 degrees as it comes out of the faucet can cause significant burns in as little as two or three seconds. When exposed to 120 degree water, on the other hand, it takes only a minute or two for the skin to begin to burn. The skin of young children and the elderly is more vulnerable to burns than that of other individuals, and scorching can be fatal for them.

The argument for 140 degrees

Why would anybody propose cooking at a higher temperature when there is a danger of scalding? Actually, another federal organization, the Occupational Safety and Health Administration, or OSHA, has determined that 140 degrees is a safer temperature to work at. The most pressing worry is the elimination of a certain strain of bacteria from the environment. The majority of homes will not have to be concerned about this because water heated to 120 degrees will kill the vast majority of common germs.

Older water systems with rusted pipes, as well as a water storage system that enables water to stagnate outdoors or for extended periods of time, are all potential risk factors for LDB bacteria growth.

Which should you choose?

The majority of houses can safely reduce the thermostat to 120 degrees Fahrenheit. If you live with children or elderly relatives, the risk of scalding is far greater than the risk of contracting a rare type of germs. When your water supply has been alerted that it is susceptible to LDB bacteria, or if you have an older system with stagnant water, you should raise the temperature of your water. If you have a delicate or weakened immune system, it’s particularly crucial to keep your body temperature higher than normal.

You may also consider purchasing a tankless water heater, which warms water only when it is required and does not require a storage tank.

If you choose any temperature setting, you will save money!

Changing the temperature on your water heater

Once you’ve determined which temperature is best for your home, you’ll need to figure out how to make the adjustment. To begin, ascertain the temperature at which your water is now running. This step is as simple as allowing the hot water from your faucet to run for a few minutes, filling a glass, and using a kitchen thermometer to check the temperature of the water. If you decide that you need to modify the temperature, you may need to reference the owner’s handbook for your water heater to see where the temperature setting is located.

If you have any difficulties changing your water heater’s settings, or if you detect a leak or another problem, a technician from Ken’s would be happy to assist you with your situation.

Plumbing Hacks, Bathroom, and Water Heaters are some of the topics covered.

How to Adjust Your Water Heater’s Temperature

It has been shown that even ordinary tap water might be hazardous. Every year, a number of individuals (mainly youngsters) are sent to hospitals after suffering burns as a result of water heaters that have been set excessively high. But what exactly does “too high” imply, and how can people ensure that their water heaters are set at a temperature that will not cause them to be burned, is a mystery. The Environmental Protection Agency (EPA) recommends a hot temperature setting of 120 degrees Fahrenheit for both safety and energy savings reasons.

Use this procedure if the stickers on the water heater do not inform you how to set the temperature and you are unable to locate the owner’s handbook.

Make sure to run hot water for at least three minutes from the faucet nearest to the water heater. Fill a glass with hot water and check the temperature
If the water temperature is higher than 120 degrees, adjust the dial, wait approximately three hours, and then check again. Continue until the water reaches 120 degrees Fahrenheit.

The temperature of the water heater should be checked the next morning before anyone uses any hot water as a last check.

Once you have found the perfect setting, make a note of it on the dial so that you do not have to go through the testing procedure again. Here are some more suggestions for extending the life of your water heater.

Family Handyman

Most houses have a water heater, which is one of their largest energy consumers. If you’re searching for ways to reduce your energy consumption, this is a smart place to start. Prior to decreasing the temperature of your water heater’s thermostat by a few degrees, there are a few things you should consider. If you set the temperature too low, you run the risk of turning your water heater into a breeding ground for potentially harmful germs. If you set it too high, you run the risk of causing a scorching mishap to yourself or someone else.

The quick answer is: 120 degrees Fahrenheit (degrees Celsius).
At this temperature, dangerous microorganisms such as the kind that causes Legionnaires’ disease are stopped from proliferating and may even be eliminated entirely.
As a result, other organizations such as the Occupational Safety and Health Administration (OSHA) suggest that the temperature of the water heater be maintained at 140 degrees Fahrenheit.
Choosing a temperature closer to 140 degrees Fahrenheit is preferable, especially if anyone in the household has a weakened immune system.
What Is the Deal with Scalding?
You’ll never know when the scorching water will hit you since it takes several seconds for hot water to travel through your pipes and reach your faucet or showerhead.
There is a remedy to the tug-of-war that exists between pathogenic safety and scalding safety: anti-scald valves are available.
Installing an anti-scald valve may be a simple do-it-yourself operation for an experienced amateur plumber, but the difficulty of the task is determined by the configuration of the plumbing system.
What, however, is the state of energy efficiency?

Saving energy and money is vital, but it isn’t nearly as important as protecting yourself and your family from potentially life-threatening diseases. Having said that, it is feasible to reduce expenses without relying on your water heater’s thermostat to do this:

Reduce the amount of hot water you use. Shower for shorter periods of time and use the dishwasher instead of hand cleaning, which often consumes more water. Insulate your hot water heater as well as the lines that supply it. There are pre-cut pieces of insulation that are simple to install and can be completed in an afternoon, making this a do-it-yourself job for the weekend. It’s time to replace your water heater. It is estimated that the average water heater will survive 8 to 12 years if it is properly maintained. Water heaters that are outdated or in need of maintenance may be significantly less efficient than they were on the day they were installed. Choose a replacement that complies with the voluntary energy efficiency requirements set by theENERGY STARprogram while buying.

Considering installing some anti-scald valves or purchasing a new water heater? Get in touch with your local Benjamin Franklin right away. Call us today at (800) 259-7705 to learn more!

Best Temperature for a Water Heater

What is the optimal temperature to set the water heater at? That is a question that many homeowners have. Previous PostNext Post This is a fantastic question, and the information provided by Aire Serv® will help you to enhance the performance, efficiency, and safety of your water heater by following the guidelines.

Determine the Best Temperature for Your Water Heater

The usual setting for most water heaters is 140 degrees Fahrenheit, but the Department of EnergyLink opens in a new tabrecommends lowering the temperature to 120 degrees Fahrenheit in order to conserve energy. To summarize, you shouldn’t drop the temperature of your tank below 120 degrees because doing so encourages bacteria development (unless you are traveling out of town, in which case the DOE suggests lowering the temperature to its lowest level). Consider the following factors that influence the temperature at which you should set your water heater:

Water heater temperature: If your dishwasher does not have a booster heater, you may wish to keep your water heater temperature at 140 degrees to get the best cleaning possible. This function, on the other hand, may be found on the majority of current dishwashers. For further information, consult your owner’s handbook. Your physical and mental well-being: While the bacteria growth within a tank set at 120 degrees is acceptable for most people, if you have a compromised immune system, you should consider maintaining your tank at 140 degrees. The amount of persons that live in your residence is as follows: It is unlikely that you will run out of hot water if you maintain the tank at 120 degrees for an extended period of time if you live alone. If, on the other hand, six family members shower back-to-back each morning, the additional 20 degrees helps to guarantee that everyone has hot water. If you have children, you should consider the following: Scalding at the faucet is less likely to occur when your water heater is set to 120 degrees, which is especially significant if you have children or elderly family members living with you.

How to Adjust the Water Heater Temperature

Perhaps you want to raise the temperature of the water heater to assist your dishwasher in doing its work more effectively, or you want to lower the temperature to reduce scalding. In any case, the following actions should be followed to alter the water heater setting:

Obtain an accurate reading of the present temperature by turning on hot water at a faucet that is the furthest away from the water heater, as shown in the diagram. Place a thermostat under flowing water to see whether or not an adjustment is required
Locate the thermostat dial by turning it clockwise: Gas water heater tanks include dials towards the bottom of the tank that regulate the temperature of the water. Water heaters that run on electricity frequently have their thermostats tucked away beneath screw-on panels. If your electric water heater contains upper and lower heating components, there may be two dials on the control panel. Take the following measurements and make the necessary adjustments: Increase or decrease the temperature setting on the thermostat by a little amount from its beginning level. Then you’ll have to wait a few of hours. Measure the water temperature once more and make any additional modifications that are necessary. Whenever you’re through, make a note of the final temperature on the dial so that you may quickly adjust it in the future.

Other Ways to Improve Water Heater Efficiency

In addition to lowering the thermostat, you may make these energy-saving modifications to your residence. To lower your water heating expenses, click on the following link, which will open in a new tab:

Insulate the water heater tank to decrease heat loss during standby mode. Renovate your bathroom by replacing your showerheads and faucets with low-flow models that use less hot water. Replace your existing water heater with a tankless one that warms water on demand, eliminating the need for storage and the accompanying standby heat loss.

Schedule Water Heater Services with Aire Serv®

Whether you need assistance changing the temperature of your water heater or you want to arrange water heater repair or replacement, you can rely on Aire Serv to complete the task. We’ll help you save money by providing thorough water heater repair services and replacing your water heater when it approaches the end of its useful life. Please call Aire Servtoday if you would like to schedule water heater services with a qualified expert. Previous PostNext Post Previous Post

What Is The Ideal Temperature For Water Heaters?

The water heater in your house is the second greatest energy consumer in your home, accounting for around 18 percent of your monthly energy cost. Making certain that your hot water heater is set to the appropriate temperature will not only help you save money on your monthly energy bills, but it will also help you extend the life of the unit as well. A simple test performed within your house will assist you in determining whether or not you should check the temperature of the unit. Turn on a faucet that only has hot water coming out of it.

Is it too hot for you to wash your hands or take a bath?
If the water never becomes warm, it is possible that the temperature is set too low.
A surprising amount of people are unaware that lowering the temperature on their air conditioning unit too low can be just as harmful as setting it too high.
A tank that is kept at a too-cold temperature can encourage the growth of germs.
The amount of elements in your home will influence whether or not you should set your unit to a temperature greater than 120°.

The Influence of Water Heater Temperature Factors Check out the recommended 120-degree setting. Depending on whether or not the water heats up sufficiently, the following factors may influence how high you should set your gauge:

Whether the device is fueled by electricity or gas
The type of pipe material used in your residence (PEX, copper, or plastic)
Whether the hot water unit is equipped with a typical tank or is tankless

If any of the following apply, putting the hot water heater between 120 and 140 degrees should be considered:

A large family necessitates greater water use
The water that comes out of the dishwasher does not pre-heat
A resident at home has a weaker immune system or is suffering from a respiratory ailment.

Hot water heaters can help you save money on energy. It is estimated that simply lowering the temperature of your hot water heater by 10 degrees, you would save three to five percent on your monthly energy bills. If you have recently acquired a hot water heater or have recently moved into a new house, double-check the settings. A temperature of 140 degrees is usually chosen as the default by most manufacturers, which may be too hot for certain houses. You may ascertain the temperature of the water by taking a reading from the water coming from the faucet or by looking at the gauge on the device.

When you turn on the hot water valve, the booster mixes the hot water with the chilly water from the input valve to provide you with a pleasant water flow.

Large families might benefit considerably from the system, which circulates hot water throughout the plumbing system so that it does not have time to chill before reaching the faucets.

Try out several temperature settings to find the one that works best for your house.