What Temperature Should I Set My Water Heater At?
Get in Touch With Us
Setting the Ideal Hot Water Heater Temperature
Are you tired of burning your hands every time you turn on the hot water in the shower? What if you’re having trouble getting a comfortable water temperature, no matter how high you turn the faucet up? These are not always indications that your water heater is malfunctioning, but rather that the temperature setting you have chosen is not optimal for your purposes. A water heater that has been installed incorrectly can have a significant influence on your life, even in areas that are not directly linked to your plumbing or heating system.
It can also have a negative influence on your health or the health of people who share your home with you.
A definitive or simple response cannot be given; rather, part of it is a matter of personal choice.
General Recommended Water Heater Temperature
You can find out what temperature water should be at by visiting the Environmental Protection Agency. The optimum water temperature is 120 degrees Fahrenheit. You will really save money because your water will not be hot enough to cause scalding, most small households will have adequate hot water for their needs, and reheating will not need an excessive amount of energy consumption, allowing you to save money on your utility bills. This temperature, on the other hand, is not ideal for everyone.
Considerations When Choosing a Water Heater Temperature Setting
Do you have any at-risk individuals residing in your home? Those who are particularly sensitive to high temperatures may suffer serious consequences if they are exposed to overly hot water. Water at 150 degrees Fahrenheit may cause third-degree burns in newborn babies in only two seconds, while water at 140 degrees can cause third-degree burns in babies in just five seconds. Temperature reduction is more safer for your infant and far more cost-effective in terms of energy use. A water heater set at no more than 130 degrees is recommended if you have a baby or any youngster under the age of three in your household.
- Those who have compromised immune systems or who suffer from respiratory ailments, on the other hand, may benefit from a hotter water temperature in order to destroy bacteria while also increasing the concentration of steam in the air when bathing.
- Do you have an appliance that is energy efficient?
- Essentially, these systems take in water and then raise the temperature to even higher levels to provide an even better and more hygienic clean, all without the need for you to raise the temperature coming from your water heater.
- If, on the other hand, it won’t be for a long time, you may wish to raise the temperature of your water heater to 140 degrees.
- How many people do you have living in your house?
- Those who like a hotter shower increase the ratio of hot to cold water in their shower.
- The temperature of the water that comes out of your water heater, on the other hand, will have an impact on this as well.
- People that use cooler water heaters will require more hot water and less cold water in order to achieve their goals.
- If you have a large home with multiple people living in it, you should raise the temperature of the water to ensure that your hot water supply lasts as long as possible.
Do you require assistance with your water heater in the Los Angeles area? Whether you want a thermostat replacement or the installation of a new water heater, contact the professionals at Moe Plumbing Services at (818) 396-8002 now.
More on Water Heaters:
- Six Common Problems with Your Home Water Heater
- What Every Homeowner Should Know About Water Heater Maintenance
- Six Common Problems with Your Home Water Heater
What’s The Best Water Heater Temperature Setting?
A hot shower may receive a bad name from your dermatologist since it might dry up your skin, but many people like it for its relaxing properties! In a household where hot water is fiercely competed for among family members, or even between your washing machine and dishwasher, you may be tempted to raise the temperature of your hot water heater. But at what point does it become too hot? There are differences of opinion between the Department of Energy and the industry. Scalding can occur at temperatures below 120 degrees Fahrenheit, although 140 degrees Fahrenheit is the normal default temperature.
Whatever temperature setting you choose, it’s vital to remember that the kind of pipe used, how the water is heated (gas or electric), and whether your system is tanked or tankless have no effect on the temperature you choose.
- Use 120°F if you have small children or the elderly in your house who are prone to third-degree burns in seconds, or if you are the sole inhabitant of your home since there is less demand for hot water. Consider 140°F if you have an immunocompromised individual in your house, a dishwasher that does not pre-heat, or if you have a large number of occupants owing to the increased need for hot water.
But what about the expenses of energy? We get what you’re saying! Water heaters account for around 14-18 percent of the total energy consumed by a residence on a typical day. Furthermore, it may be tempting to lower the temperature in order to save money. It should be noted that a 10°F decrease in temperature is related with a 3-5 percent reduction in energy use. Legionella, on the other hand, can live at temperatures as high as 122°F. So make sure to strike a balance between your risk tolerance and your energy consumption targets!
- Many hot water heaters are equipped with a temperature control dial.
- Start with 120°F and gradually increase the temperature in small increments until you get your desired result.
- A water tank booster may be an appropriate option in houses where the requirement to maintain a greater hot water temperature for health safety must be balanced with the need to reduce the danger of scorching.
- Alternatively, you could live in a house where, no matter what temperature you select, hot water takes an inordinate amount of time to reach the faucet (or a certain tap farthest from the hot water heater).
- Whatever you choose, we’re only a phone call away if you’re having issues with your hot water!
What Temperature Should a Hot Water Heater Be Set At?
Previous PostNext PostYour water heater accounts for around 18 percent of the energy consumed by your house. If the temperature of your water heater is set too high, you will be forced to pay the price in your monthly energy bill. The converse is true: if you have your water heater set too low, your water may not get hot enough (resulting in short showers), or worse, it may get contaminated with germs. Maintain a 120-degree temperature for your water heater at all times because infections can form in the stagnant water within the water heater, notably Legionella, which is extremely deadly.
In addition to being hot enough to keep viruses at away while not being scorching hot enough to cause blistering, 120 degrees will provide adequate hot water for most small households while still being relatively energy-efficient, according to the Environmental Protection Agency.
However, depending on a few criteria, the most appropriate setting for you may differ.
Factors That Affect Hot Water Temperature Setting
These criteria are unaffected by the kind of piping you have (PEX, PVC, or copper), the method of heating the water (gas or electric), or even if you have a tankless hot water heater installed.
- Owners of dishwashers that do not pre-heat the water may wish to set their water heater temperature to 140 degrees
- Elderly or families with young children may want to keep the temperature at 120 degrees. BabyCenter.com states that “it takes just two seconds for a kid to acquire third-degree burns from water that is 150 degrees and five seconds if the water is 140 degrees, the temperatures at which hot water heaters frequently leave the manufacturer.” It is recommended that the hot water temperature be maintained at 140 degrees in homes with people who have a compromised immune system or respiratory problems. Because there is less demand for hot water and hence less money spent on hot water, many people who live alone prefer a lower temperature within an acceptable range. The temperature of the water tank is often set higher in big households, in order to support the increased demand for hot water
- Nevertheless, if you want to save money, every 10 degrees you lower the temperature of the water tank thermometer, you save 3 to 5 percent on your energy bill.
Are you still undecided? To begin, set the temperature to 120 degrees Fahrenheit and gradually raise it in small increments until you reach the desired shower temperature.
What’s Your Current Temperature Setting?
Check the temperature setting on the water heater (if one is available) or take a temperature reading from the faucet to determine what it is currently. After turning on the hot water faucet, allow it to run for a few minutes before getting the temperature reading.
Solutions to Common Hot Water Tank Problems
If you’re concerned about pathogens in your hot water, as well as the possibility of scalding water, you might consider installing a hot water tank booster. This allows you to maintain your water at 140 degrees in the tank while mixing it with cold water to bring the temperature down to 120 degrees before it reaches the faucet. Having a hot water circulating system installed in your home might alleviate the problem of waiting for hot water to reach the faucet in a large household. This method circulates hot water slowly through the pipes in order to prevent it from cooling down before it reaches the faucet.
Professional Plumbing Services
It’s possible that your hot water isn’t hot enough no matter what setting your water heater is set to. If you need assistance adjusting your hot water heater or troubleshooting any difficulties, call your local Mr. Rooter Plumbing at (855) 982-2028 or submit a request for a free estimate on our website. Not only does your hot water need to be “just perfect,” but so does everything else in your home. Aire Serv, a neighborly firm, can assist you in determining the optimal air temperature. Previous PostNext Post Previous Post
Risks Of Too High Or Too Low Water Heater Temperature
You might be wondering what temperature to put your water heater to. When you purchase a water heater unit, the temperature is typically set by the manufacturer. However, this does not rule out the possibility of having some control over its temperature. The good news is that you may set the temperature to a level that is comfortable for you while yet ensuring the safety of your family. Previous to this, we wrote an article in which we spoke about how the heat in your shower might suddenly vary.
The temperature of the device is important since it can have an impact on how well it performs.
Top Risks of setting your unit temperature too high
You might be wondering what temperature to put your water heater at. A water heater unit is normally pre-programmed when it is purchased from the manufacturer. However, this does not preclude you from being able to regulate the temperature of the machine. Good news: you have the ability to choose a comfortable temperature for your family while yet ensuring their safety. A few weeks ago, we wrote an article about how your shower’s temperature might suddenly fluctuate. For example, a malfunction with your water heater is one of the possible causes.
Although the temperature of the device is important, it can have an impact on how well it performs. In this article, we will discuss the dangers of setting your water heater’s temperature too high or too low, as well as the optimal temperature for it to perform efficiently.
1. Scalding Accidents
Setting the temperature too high might result in scorching mishaps that result in burn injuries. According to the findings of a study on water heater temperature and attributes, many water heaters are frequently set at dangerously high temperatures. Several studies by the Centers for Disease Control and Prevention (CDC) have discovered that scald burns are the most common cause of injury in younger children. Every day, over 300 children between the ages of 0 and 19 are treated in emergency departments for burn-related injuries, with two of these children dying as a result of their injuries.
Accidents such as this may be prevented by allowing your water to flow for three minutes and then monitoring the temperature with a candy thermometer thereafter.
2. High electricity bill
Warning: Using a water heater with the temperature set too high will cause your energy cost to rise! According to the Department of Energy, standby heat losses from your water heater can cost you anywhere from $36 to $61 per year in energy savings. The good news is that by lowering your thermostat, you may save anywhere from 4 percent to 22 percent on your annual energy expenditure. Lowering the temperature of your water heater can help to decrease standby heat loss, which is one of the reasons you have a high energy cost.
3. Lowers your unit’s service life
According to some sources, hot water can accelerate the accumulation of hard water mineral silt, particularly calcium carbonate, in the tank’s interior. It is possible that the buildup would cause corrosion in the water heater tank, which will result in a reduction in the estimated lifespan of the complete device. Leaks and polluted water might occur as a result of the rust accumulation in the storage tank. Another major reason for water heater failure is the deposit of rust on the interior of the heater.
We wrote an essay about why it’s important and how you can extend its lifespan.
Risk of setting your unit temperature too low
If you want to save money on energy costs, you should avoid setting the temperature of your unit too low. It is possible that you will have a health problem as a result.
1. Legionnaires disease
Alternatively, you will not want your unit’s temperature to be set too low, since this can result in condensation. A health problem might result if you do so.
Ideal Temperature For Your Water Heater
The optimum temperature is. What several agencies have to say about the optimal temperature is summarized below: According to the Occupational Safety and Health Administration (OSHA) and the World Health Organization (WHO), water heaters kept below 60 degrees Celsius (140 degrees Fahrenheit) may promote Legionella development. This temperature, on the other hand, will almost certainly increase the likelihood of being burned by searing hot water. If you have young children at home, the Centers for Disease Control and Prevention (CDC) and the Energy Department recommend that you set your water heater’s thermostat to 120°F or lower.
To do this, set your thermostat to a steady temperature. This will help you keep control over the water temperature throughout your home, preventing it from being overly hot.
So, is it 120°F or 140°F?
A temperature of. degrees Celsius is considered optimal. Here is what several authorities have to say about the optimal temperature: According to the Occupational Safety and Health Administration (OSHA) and the World Health Organization (WHO), water heaters that are kept below 60 degrees Celsius (140 degrees Fahrenheit) may promote the growth of Legionella. It is possible that being exposed to scorching hot water at this temperature will increase the risk of being burnt. Setting your water heater’s thermostat to 120°F or below is recommended by the Centers for Disease Control and Prevention and the Energy Department.
This will help you keep control over the water temperature in your home, preventing it from becoming excessively hot.
Your installer can help you adjust your water heater temperature.
As part of our service, our qualified specialist at SPS Plumber can assist you with setting the temperature of your water heater to the proper setting. In addition, we can do annual water heater maintenance on your unit. To schedule an appointment, please call us at 408-622-8183 (South Bay Area) or 209-597-9107 (Central Valley) right away!
Should You Adjust Your Water Heater Temperature?
Most houses have a water heater, which is one of their largest energy consumers. If you’re searching for ways to reduce your energy consumption, this is a smart place to start. Prior to decreasing the temperature of your water heater’s thermostat by a few degrees, there are a few things you should consider. If you set the temperature too low, you run the risk of turning your water heater into a breeding ground for potentially harmful germs. If you set it too high, you run the risk of causing a scorching mishap to yourself or someone else.
- The quick answer is: 120 degrees Fahrenheit (degrees Celsius).
- At this temperature, dangerous microorganisms such as the kind that causes Legionnaires’ disease are stopped from proliferating and may even be eliminated entirely.
- As a result, other organizations such as the Occupational Safety and Health Administration (OSHA) suggest that the temperature of the water heater be maintained at 140 degrees Fahrenheit.
- Choosing a temperature closer to 140 degrees Fahrenheit is preferable, especially if anyone in the household has a weakened immune system.
- What Is the Deal with Scalding?
- You’ll never know when the scorching water will hit you since it takes several seconds for hot water to travel through your pipes and reach your faucet or showerhead.
- There is a remedy to the tug-of-war that exists between pathogenic safety and scalding safety: anti-scald valves are available.
- Installing an anti-scald valve may be a simple do-it-yourself operation for an experienced amateur plumber, but the difficulty of the task is determined by the configuration of the plumbing system.
- What, however, is the state of energy efficiency?
Saving energy and money is vital, but it isn’t nearly as important as protecting yourself and your family from potentially life-threatening diseases. Having said that, it is feasible to reduce expenses without relying on your water heater’s thermostat to do this:
- Reduce the amount of hot water you use. Shower for shorter periods of time and use the dishwasher instead of hand cleaning, which often consumes more water. Insulate your hot water heater as well as the lines that supply it. There are pre-cut pieces of insulation that are simple to install and can be completed in an afternoon, making this a do-it-yourself job for the weekend. It’s time to replace your water heater. It is estimated that the average water heater will survive 8 to 12 years if it is properly maintained. Water heaters that are outdated or in need of maintenance may be significantly less efficient than they were on the day they were installed. Choose a replacement that complies with the voluntary energy efficiency requirements set by theENERGY STARprogram while buying.
Considering installing some anti-scald valves or purchasing a new water heater? Get in touch with your local Benjamin Franklin right away. Call us today at (800) 259-7705 to learn more!
Best Temperature for a Water Heater
What is the optimal temperature to set the water heater at? That is a question that many homeowners have. Previous PostNext Post This is a fantastic question, and the information provided by Aire Serv® will help you to enhance the performance, efficiency, and safety of your water heater by following the guidelines.
Determine the Best Temperature for Your Water Heater
The usual setting for most water heaters is 140 degrees Fahrenheit, but the Department of EnergyLink opens in a new tabrecommends lowering the temperature to 120 degrees Fahrenheit in order to conserve energy. To summarize, you shouldn’t drop the temperature of your tank below 120 degrees because doing so encourages bacteria development (unless you are traveling out of town, in which case the DOE suggests lowering the temperature to its lowest level). Consider the following factors that influence the temperature at which you should set your water heater:
- Water heater temperature: If your dishwasher does not have a booster heater, you may wish to keep your water heater temperature at 140 degrees to get the best cleaning possible. This function, on the other hand, may be found on the majority of current dishwashers. For further information, consult your owner’s handbook. Your physical and mental well-being: While the bacteria growth within a tank set at 120 degrees is acceptable for most people, if you have a compromised immune system, you should consider maintaining your tank at 140 degrees. The amount of persons that live in your residence is as follows: It is unlikely that you will run out of hot water if you maintain the tank at 120 degrees for an extended period of time if you live alone. If, on the other hand, six family members shower back-to-back each morning, the additional 20 degrees helps to guarantee that everyone has hot water. If you have children, you should consider the following: Scalding at the faucet is less likely to occur when your water heater is set to 120 degrees, which is especially significant if you have children or elderly family members living with you.
How to Adjust the Water Heater Temperature
Water heater at 140 degrees: If your dishwasher does not have a booster heater, you may want to maintain your water heater at 140 degrees to ensure that it cleans the most effectively. Modern dishwashers, on the other hand, are equipped with this capability by default. For further information, consult your owner’s handbook. In terms of your physical well-being, While bacteria growth in a tank at 120 degrees is generally considered safe for most individuals, those with a compromised immune system might consider maintaining their tank at 140 degrees.
The extra 20 degrees, on the other hand, can assist ensure that everyone has hot water when six family members shower back-to-back each morning.
This is especially significant if you have children or elderly people living with you.
- Water heater at 140 degrees: If your dishwasher does not have a booster heater, you may want to maintain your water heater at 140 degrees to ensure that it cleans the dishes thoroughly. This function, on the other hand, is featured on the majority of current dishwashers. More information can be found in your owner’s handbook. Your physical well-being: While bacteria growth in a tank set at 120 degrees is generally considered safe for most individuals, those with a compromised immune system might consider maintaining their tank at 140 degrees. The number of persons that live in your house is as follows: When you keep the tank at 120 degrees, it’s unlikely that you’ll ever run out of hot water if you live alone. If, on the other hand, six family members shower back-to-back each morning, the extra 20 degrees helps to guarantee that everyone has hot water. If you have children, you should: Scalding at the faucet is less likely to occur when your water heater is set to 120 degrees, which is especially significant if you have children or elderly people living with you.
Other Ways to Improve Water Heater Efficiency
In addition to lowering the thermostat, you may make these energy-saving modifications to your residence. To lower your water heating expenses, click on the following link, which will open in a new tab:
- Additionally, you may implement these home energy improvements in addition to turning the thermostat down. To reduce your water heating expenses, click on the following link, which will open in a new tab:
Schedule Water Heater Services with Aire Serv®
Whether you need assistance changing the temperature of your water heater or you want to arrange water heater repair or replacement, you can rely on Aire Serv to complete the task. We’ll help you save money by providing thorough water heater repair services and replacing your water heater when it approaches the end of its useful life. Please call Aire Servtoday if you would like to schedule water heater services with a qualified expert. Previous PostNext Post Previous Post
How to Adjust Your Water Heater’s Temperature
It has been shown that even ordinary tap water might be hazardous. Every year, a number of individuals (mainly youngsters) are sent to hospitals after suffering burns as a result of water heaters that have been set excessively high. But what exactly does “too high” imply, and how can people ensure that their water heaters are set at a temperature that will not cause them to be burned, is a mystery. The Environmental Protection Agency (EPA) recommends a hot temperature setting of 120 degrees Fahrenheit for both safety and energy savings reasons.
Use this procedure if the stickers on the water heater do not inform you how to set the temperature and you are unable to locate the owner’s handbook.
- Make sure to run hot water for at least three minutes from the faucet nearest to the water heater. Fill a glass with hot water and check the temperature
- If the water temperature is higher than 120 degrees, adjust the dial, wait approximately three hours, and then check again. Continue until the water reaches 120 degrees Fahrenheit.
The temperature of the water heater should be checked the next morning before anyone uses any hot water as a last check. Once you have found the perfect setting, make a note of it on the dial so that you do not have to go through the testing procedure again. Here are some more suggestions for extending the life of your water heater.
You probably don’t give your water heater much thought till you’re in the middle of a shower and the hot water stops working. It might be much more dangerous if the water is overly hot and causes scorching. Although you have the ability to modify the temperature of your water heater, should you? Even while you would believe that water heaters have a standard suggested temperature, this is not the case. Some water heater manufacturers factory-set their water heaters at 120°F (49°C), while others factory-set their water heaters at a default temperature of 140°F (60°C).
The Occupational Safety and Health Administration (OSHA) advises that the temperature be maintained at or above 122 degrees to assist avoid the formation of potentially dangerous microorganisms in the workplace.
Should I Change the Water Heater Temperature?
For the purpose of determining the most appropriate water heater temperature for your house, there are various elements to take into consideration.
Hot Water Kills Harmful Pathogens
A health problem arises when Legionella, the bacterium that causes Legionnaires’ disease, develops in the water systems of residential properties. According to the Occupational Safety and Health Administration, water heaters that are kept below 140 degrees and that include scale and silt may promote Legionella growth. Fortunately, the vast majority of healthy persons who are exposed to Legionella do not become ill. However, before you decide to turn up the temperature dial on your water heater, consider the following.
Hot Water Can Scald
The use of hot tap water is a leading cause of burn injuries and fatalities. Scald burns can be a serious threat in the house, especially if you have young children or elderly people living with you. Young children, because their skin is thinner, and the elderly, because their skin might be less sensitive to warmth and may be slower to respond to scalding water, are the two age categories that are most at risk for scalds. Adults may suffer third-degree burns if they are exposed to 150-degree water for even a brief period of time (as little as two seconds), according to the Consumer Product Safety Commission.
Though the temperature reaches 120 degrees, a five-minute exposure might result in third-degree burns even if the temperature is lower.
Minimize Risk with Anti-Scald Devices
The question then becomes, how do you balance the hazards of bacteria development with potential scalding? Anti-scald guards and devices are normally installed in newer homes, but if you live in an older home, you may install anti-scald guards and devices in showerheads and tub spouts to help prevent dangerously hot water from escaping.
Consult with a plumber about installing a thermostatic mixing valve (also known as a tempering valve or an anti-scald valve), which restricts the maximum temperature that may be discharged from your hot water heater.
Will Changing the Water Heater Temperature Save Money?
The temperature at which you set your water heater can make a significant impact in the amount of electricity your home consumes. It is estimated that the water heater accounts for between 17 and more than 25 percent of your monthly energy bills, making it one of the most expensive single items on your home energy bill. Turning down your water heater temperature, according to the Energy Department, results in a considerable reduction in the expenses of standby losses, which are heat losses from your water heater into the surrounding region.
Reduced temperatures can result in more savings when doing duties such as washing clothing, taking showers, and dishwashing, among others.
What is My Water Heater Temperature?
You won’t be able to identify the temperature of most tank water heaters and some tankless water heaters merely by glancing at the temperature dial, because most are simply designated from “Low” to “Hot” (or “Very Hot”) on the dial. It is recommended that you consult your water heater’s handbook for the preset temperature. If you don’t know what you’re looking for, simply search the internet for the brand and kind of water heater you have, as well as the “default temperature.” However, the default temperature of the water heater is not always the same as the temperature of the water that is flowing out of your faucets.
How to Check Your Tap Water Temperature
- Avoid using your hot water for at least two hours before doing the test. If you have a tankless water heater, you can skip this step
- Otherwise, proceed as directed. Allow for a minimum of three minutes of running hot water. Make sure the temperature is correct by using a candy, meat, or water thermometer
- Set the temperature on your water heater’s thermostat to a more comfortable level. Continually repeat steps 2 and 3 until you get the required temperature. Wait for a full day to enable the water temperature to fluctuate before testing it once more. If you have a tankless water heater, you may skip this step.
Pro tip: Once you’ve found the temperature you desire, mark the location on the temperature dial of your water heater using a permanent marker.
Find the Right Water Heater Temperature
Your water heater’s “optimal” temperature is essentially a matter of personal preference – for your own level of comfort, any potential safety problems, your monthly utility cost, and energy efficiency considerations.
Home Warranty Coverage for Water Heaters
Maintenance of your water heater on a regular basis can assist to prevent malfunctions and may even help to increase the lifespan of the equipment. In certain cases, even the most attentive maintenance will not be enough to avoid the onset of a problem with your water heater. When equipment such as your water heater quit operating, a home warranty can protect your budget from unexpected repair or replacement expenditures that may add up quickly. See what additional appliances and home systems you can protect with a home warranty plan, or request a quotation right away.
What Is The BEST Water Heater Temperature Setting?
Please keep in mind that this content may contain affiliate links. This means that, at no additional cost to you, we may gain a small profit on purchases made via our links.
If you have already set the temperature and are thinking to yourself, “I don’t have any hot water,” or “I don’t have enough hot water,” there are a few variables that might be causing the problem. If all else fails, it’s possible that the heating element is faulty and has to be replaced.
How To Check Your Water Heater Temperature
The majority of water heaters do not have a temperature gauge with a digital readout on them. Temperatures or heating ranges are marked on thethermostat, rather than numbers. A cup and a culinary thermometer will be required in order to correctly determine the temperature of the hot water heater. If you haven’t used your water heater in at least one hour, turn on the faucet that is nearest to it. Allow the water to run for at least one minute to ensure that the water is at its warmest possible temperature before filling the cup with it.
Recommended Temperature Settings
Water heaters are pre-programmed to operate at OSHA-recommended temperatures, which are around 140 degrees. The Environmental Protection Agency, on the other hand, recommends lowering the thermostat down to 120 degrees Fahrenheit to save power use and using a booster heater to attain sanitizing temperatures at certain outlets. Another point of view is that lower temperatures are preferable for homes with little children, although higher temperatures are more effective in cleaning and sanitizing surfaces.
However, the temperature is low enough to avoid scorching while being high enough to destroy hazardous microorganisms.
How To Turn Up Your Water Heater
If you are dissatisfied with the suggested temperature of your hot water heater, you may alter the settings to receive extra hot water. Although electric water heaters may require a screwdriver and potentially a tiny wrench or socket, most hot water heater settings are straightforward to modify. Keep in mind that the thermostat is factory configured to a recommended temperature, and that altering the setting may increase the risk of significant burns from the appliance.
How to Set Temperature on a Gas Water Heater
In case you are dissatisfied with the suggested temperature of your hot water heater, you may alter the settings to receive extra hot water. Although electric water heaters may require a screwdriver and possibly a tiny wrench or socket, the settings for gas water heaters are simple to alter. Always keep in mind that the thermostat is factory configured to a suitable temperature, and that adjusting it may increase the likelihood of catastrophic burns.
- Warm = 80-90°
- Low = 80-90°
- Hot (or triangle symbol) = 120°
- A= 130°
- B= 140°
- C= 150°
- Very Hot = 160°
- High = 120°
There is a “Vacation” setting that appears from time to time. This does not heat the water, but it does ensure that the pilot light remains lit.
How to Set Temperature on an Electric Water Heater
Turn off the circuit breaker if necessary. Remove the access panels from the room. Under the insulation, look for the thermostat adjustment screwhole. Adjust the thermostat control to the appropriate temperature by using a straight screwdriver to make the adjustment. After replacing the insulation and panels, the power should be restored. Here’s a good video that demonstrates the procedure:
Factors That Affect Water Temperature
The circuit breaker should be turned off. Toss out the doors and windows. Under the insulation, look for the thermostat adjustment.
Adjust the thermostat control until it reaches the appropriate temperature by using a straight screwdriver. Replacing the insulation and panels is the next step, followed by the re-connection of the electrical service. Listed below is a helpful video that demonstrates the procedure:
What Is The Ideal Temperature For Water Heaters?
The water heater in your house is the second greatest energy consumer in your home, accounting for around 18 percent of your monthly energy cost. Making certain that your hot water heater is set to the appropriate temperature will not only help you save money on your monthly energy bills, but it will also help you extend the life of the unit as well. A simple test performed within your house will assist you in determining whether or not you should check the temperature of the unit. Turn on a faucet that only has hot water coming out of it.
- Is it too hot for you to wash your hands or take a bath?
- If the water never becomes warm, it is possible that the temperature is set too low.
- A surprising amount of people are unaware that lowering the temperature on their air conditioning unit too low can be just as harmful as setting it too high.
- A tank that is kept at a too-cold temperature can encourage the growth of germs.
- The amount of elements in your home will influence whether or not you should set your unit to a temperature greater than 120°.
- Depending on whether or not the water heats up sufficiently, the following factors may influence how high you should set your gauge:
- Each month, your home’s water heater consumes around 18 percent of its total energy consumption, ranking it as the second highest source of energy use. Making certain that your hot water heater is set to the appropriate temperature will not only help you save money on your monthly energy bills, but it will also help you extend the life of the unit as well. You can determine whether or not you need to monitor the temperature of the unit by doing a simple test within your house. To use only hot water, turn on a faucet. Allow the water to heat up as much as possible before using it again. It is too hot to wash your hands or take a bath, isn’t it? Your water heater’s temperature may be set too high if you find yourself in this situation. The temperature of the water may be set too low if it never becomes warm. A Water Heater’s Optimum Operating Temperature Water heaters should be set at 120 degrees Fahrenheit, however depending on your home, this may not be the most efficient setting. A surprising amount of people are unaware that lowering the thermostat on their air conditioning unit too low can be just as harmful as setting it to a high range. Setting the water heater below 120 degrees Fahrenheit will ensure that cold showers are the least of your concerns. In the tank, germs will thrive if the temperature is kept too chilly. Legionella thrives in stagnant, chilly water, and it can produce a severe flu-like sickness if the water becomes stagnant and cool. When deciding whether or not to set your unit higher than 120 degrees, consider the amount of factors in your house. Thermal Factors in a Water Heating System The recommended 120-degree setting should be tried first. Following are some factors that may influence how high you should set your gauge if the water doesn’t heat up quickly enough:
If any of the following apply, putting the hot water heater between 120 and 140 degrees should be considered:
- A large family necessitates higher water use. The water that comes out of the dishwasher does not pre-heat
- A resident at home has a weaker immune system or is suffering from a respiratory ailment.
Hot water heaters can help you save money on energy. It is estimated that simply lowering the temperature of your hot water heater by 10 degrees, you would save three to five percent on your monthly energy bills. If you have recently acquired a hot water heater or have recently moved into a new house, double-check the settings. A temperature of 140 degrees is usually chosen as the default by most manufacturers, which may be too hot for certain houses. You may ascertain the temperature of the water by taking a reading from the water coming from the faucet or by looking at the gauge on the device.
When you turn on the hot water valve, the booster mixes the hot water with the chilly water from the input valve to provide you with a pleasant water flow.
Large families might benefit considerably from the system, which circulates hot water throughout the plumbing system so that it does not have time to chill before reaching the faucets.
Try out several temperature settings to find the one that works best for your house. Alternatively, if you believe the temperature is not adjusting effectively, contact a plumber who specializes in water heater problems.
What temperature is right for your water here?
When it comes to conserving energy at home, one of the first things that comes to mind is most likely changing the thermostat settings on your home heating system to the lowest possible level. Nevertheless, what about the temperature control device on your water heating system? The factory default setting on most water heaters supplied today is 140 degrees, and sometimes even higher – a temperature that is high enough to induce scorching but not high enough to meet the needs of most people (there are exceptions to this, however, as we will see).
However, the most compelling reason to lower your water temperature is to save electricity (and, consequently, money).
When you adjust your water heater’s thermostat to 120 degrees Fahrenheit rather than 140 degrees Fahrenheit, you’ll save around $50 per year in standing heat loss and more than $400 per year in fuel use.
A 140° setting is right in certain circumstances
However, while the majority of individuals can get by with a 120-degree setting, there are some situations in which a 140-degree setting is more appropriate. For example, if you have a member of your family who has a compromised immune system or chronic respiratory condition, a 140-degree setting is suggested to avoid Legionnaires’ disease and other water-borne illnesses. Additionally, if your dishwasher does not pre-heat the water, you may want to keep the temperature at a higher setting.
Checking your water heater thermostat temperature
This video from the United States Department of Energy will help you determine what temperature your hot water heater is set at and how to modify it. For any more assistance, please contact us and we will lead you through the process step by step. In the event that your water heater is having difficulty maintaining its temperature, or if you’re experiencing other water heater difficulties such as strange noises, a sulfur smell, or sediment buildup, please call us immediately. Repair and replacement of water heaters are available throughout western Massachusetts, and we can provide you with a FREE quote on a water heater upgrade for your house.
For additional information, please contact us immediately!
What Temperature Should I Set My Water Heater?
Water heaters are a critically vital component of your house, but most homeowners don’t give them much thought once they’ve been installed in the first place. Unfortunately, installations completed before you moved in or by specialists who don’t take the time to ensure that the unit is running properly might result in incorrect water heater temperatures being reached. On the one hand, scorching hot water can be dangerous, while on the other, water that does not stay hot long enough to hinder the growth of hazardous germs can be quite dangerous.
How can you tell if the temperature of your water heater is the proper one? Consider the following questions for yourself:
- Is it possible that the base temperature of the water heater has altered after it was initially installed? Water heaters used to be manufactured at a temperature of 140°F, which may induce scorching in as little as 5 seconds. Some heaters are set at a temperature of 160°F, which is far too high. A fraction of a second at that temperature will result in third-degree burns. Water heaters are now factory-set at 122.5°F, which is a much safer setting
- If the temperature has been adjusted, it is possible that the temperature has been set too low. A water temperature that is set too low is no more beneficial than a temperature that is set too high. Low temperatures, between 90 and 115 degrees Fahrenheit, might foster the growth of germs that can make you or your family very sick. It is necessary to prevent temperatures that are too low.
So What is the Best Water Heater Temperature Setting?
The majority of specialists think that the best temperature range for personal comfort and safety is 120°F to 125°F. Using this setting, you can prevent bacterial development while not having to worry about possible damage from being caused by hot temperatures. An additional benefit of decreasing the temperature is that you will save money on your energy costs. It’s also a good idea to spend some time getting acquainted with your water heater, which is often disregarded but is a vital component of your home’s plumbing system.
Water Heater Help from the Pros
Your water heater must operate at peak efficiency in order to provide a safe and comfortable environment. Corley’s team of experiencedGreenville plumbers is here to assist you! Our service personnel take great pleasure in not just providing excellent client service, but also in their technical knowledge. You can rely on us to provide you with the best water heater possible! Not only can we do preventative maintenance and identify little problems before they become major problems, but we can also install new water heaters!
Give us a call or send us a message online now.
How Your Water Heater Works
Your water heater must operate at peak efficiency in order to provide a safe and pleasant household. It is our pleasure to assist you with your plumbing needs inGreenville. In addition to providing excellent customer service, our service personnel take great pleasure in their technical knowledge and skill-level. You can rely on us to provide you with the best water heater available! Preventative maintenance is important because it allows us to identify tiny problems before they become major problems.
Interested in learning more or arranging a service appointment?
Contact Us Right Away for Water Heater Assistance.
How to adjust your water heater temperature
Your water heater must operate at peak efficiency in order to provide a safe and pleasant environment in your home. At Corley, our knowledgeable Greenville plumbers are here to assist you. Our service personnel take great satisfaction in not just providing excellent client service, but also in their technical competence. We’ve got you covered when it comes to water heaters! Not only can we do preventative maintenance and identify minor issues before they become major issues, but we can also install new water heaters!
Give us a phone or send us an email right now!
The correct temperature range
It is recommended that your water heater be set within a specified temperature range for a variety of different reasons. A low temperature setting not only results in hot water that is merely lukewarm at best, but it can also promote bacterial development, which can lead to illnesses such as Legionnaires’ disease. This may be avoided by adjusting the temperature of the water heater to a level at which the bacteria Legionella cannot survive. A temperature of at least 140 degrees Fahrenheit (60 degrees Celsius) for water heaters is recommended by the Occupational Safety and Health Administration (OSHA) to prevent Legionella and other germs from growing in the water.
- The time it takes for third-degree burns to occur at 150 degrees Fahrenheit (66 degrees Celsius) is less than two seconds.
- Not to mention that a water heater that is set too hot might result in an excessively expensive power bill.
- The greater the distance between a faucet and the water heater, the greater the amount of heat that will be lost as the water flows, especially if the pipes are not insulated.
- When determining the appropriate temperature for your family and household, use your best judgment.
Make an adjustment, test it, and continue the process until you’ve found the ideal temperature setting for your house and water heater, which may take many attempts. Currently playing: Keep an eye out for this: Take a look inside the CNET Guide to Smart Living. 1:00
Adjusting water heater temperature
The interface used to control the temperature of a water heater will differ depending on the kind and model. Fortunately, the majority of water heater models can be modified in the same way. For example, most contemporary gas and electric water heaters are equipped with a thermostat concealed behind an insulated access panel. Electric water heaters are frequently equipped with two thermostats: one at the top of the tank and another at the bottom. Furthermore, most tankless water heaters include a display with a temperature reading as well as controls for altering the water heater’s temperature.
Turn on the water in the bathroom or kitchen sink and let it to run until the water is completely hot before using.
The process of adjusting a tankless water heater is quite similar to the process of adjusting your air conditioning thermostat. Adjust the temperature by using the digital control panel, which may be adjusted up or down as desired.
Gas or electric water heaters
Some gas water heaters include a dial towards the bottom of the device that may be adjusted simply by turning it – no tools are required for this operation. Nonetheless, most current tank water heaters (whether gas or electric) require a bit more effort, but the process is still straightforward and should only take a few minutes.
- Turning off the water heater’s electricity at the circuit breaker is the first step. To remove a thermostat(s), locate the access panel for the thermostat(s) and remove it using a screwdriver
- Remove the insulation by peeling it back. To adjust the thermostat, use a flathead screwdriver to turn it up or down.
- If your water heater has two thermostats, make sure they are both set to the same temperature. The temperature on the top thermostat should be a few degrees higher than on the bottom thermostat.
- Replace the insulation and re-install the access panel, if necessary. Reconnect the water heater’s power supply
- It is possible that you may need to relight the pilot light on a gas water heater.
Once you’ve made the necessary adjustments, you should wait at least three hours before checking the water temperature once more. It is possible that you may need to make more modifications in order to get the desired temperature. If you’ve increased the temperature and are still getting chilly showers, it’s possible that your hot water heater has to be serviced or completely replaced. Is the energy efficiency of your home high? Here are five different methods to find out. CNET’s Guide to Smart Livingis a one-stop shop for tips, techniques, and how-to guides that can help you live a more intelligent life.
What Temperature Should I Set for My Water Heater?
adminon posted a new comment 5:33:44 a.m. on May 25, 2017 It is possible to set a maximum temperature on your home’s water heater, which governs how hot the water coming out of your faucets may be at any one moment. While most of us don’t consider this to be a modifiable setting, it is in fact something that you can modify if you so want. A new water heater is usually set to a maximum temperature of 140 degrees Fahrenheit when it is first installed. Some believe that is the optimal temperature, while others believe that it is preferable to lower the maximum temperature to 120 degrees.
Here is a deeper look at what they are:
The argument for 120 degrees
As recommended by the United States Department of Energy and the American Society of Sanitary Engineering, the best temperature to set for a hot water heater should be 120 degrees Fahrenheit. The following are some advantages:
- It is more beneficial to the environment. Not only does it need electrical or gas energy to heat your water, but it also takes energy to keep the water in the storage tank at that temperature (so you have hot water on demand). By lowering the temperature by 20 degrees, you may dramatically reduce the amount of energy consumed, resulting in significant savings. The energy savings are beneficial not just to the environment, but also to your money, with the potential to save you up to $60 per year. It also helps to avoid mineral accumulation. Using cooler water means that minerals are less likely to be deposited in your pipes, reducing the troubles caused by hard water and keeping your water flow unimpeded
- It also helps to prevent severe scalding. This is, without a doubt, the most compelling of the arguments. Water that is 140 degrees as it comes out of the faucet can cause significant burns in as little as two or three seconds. When exposed to 120 degree water, on the other hand, it takes only a minute or two for the skin to begin to burn. The skin of young children and the elderly is more vulnerable to burns than that of other individuals, and scorching can be fatal for them.
The argument for 140 degrees
Why would anybody propose cooking at a higher temperature when there is a danger of scalding? Actually, another federal organization, the Occupational Safety and Health Administration, or OSHA, has determined that 140 degrees is a safer temperature to work at. The most pressing worry is the elimination of a certain strain of bacteria from the environment. The majority of homes will not have to be concerned about this because water heated to 120 degrees will kill the vast majority of common germs.
Older water systems with rusted pipes, as well as a water storage system that enables water to stagnate outdoors or for extended periods of time, are all potential risk factors for LDB bacteria growth.
Which should you choose?
The majority of houses can safely reduce the thermostat to 120 degrees Fahrenheit. If you live with children or elderly relatives, the risk of scalding is far greater than the risk of contracting a rare type of germs. When your water supply has been alerted that it is susceptible to LDB bacteria, or if you have an older system with stagnant water, you should raise the temperature of your water. If you have a delicate or weakened immune system, it’s particularly crucial to keep your body temperature higher than normal.
You may also consider purchasing a tankless water heater, which warms water only when it is required and does not require a storage tank.
If you choose any temperature setting, you will save money!
Changing the temperature on your water heater
Once you’ve determined which temperature is best for your home, you’ll need to figure out how to make the adjustment. To begin, ascertain the temperature at which your water is now running. This step is as simple as allowing the hot water from your faucet to run for a few minutes, filling a glass, and using a kitchen thermometer to check the temperature of the water. If you decide that you need to modify the temperature, you may need to reference the owner’s handbook for your water heater to see where the temperature setting is located.
If you have any difficulties changing your water heater’s settings, or if you detect a leak or another problem, a technician from Ken’s would be happy to assist you with your situation.
Plumbing Hacks, Bathroom, and Water Heaters are some of the topics covered.