How To Turn On Pilot Light On Water Heater

How to Light a Water Heater Pilot Light

Prev PostNext PostWhen the pilot light on a water heater goes out, it is typically because of a natural fluctuation in gas pressure, which extinguished the flame. The most obvious indicator that a pilot light has gone out is the one that everyone dreads: the water will not heat up properly. In the event of a damaged flame sensor, it’s critical to know how to relight the pilot light on your water heater so you can get the flame going as quickly as possible. This will not only allow you to get your hot showers back, but it will also ensure that no gas is unintentionally discharged into the home.

However, for the vast majority of gas-powered water heaters, you should begin by locating the gas shut-off valve on the water heater, which is generally plainly labeled on the front lower section of the water heater, before proceeding.

  1. Open the door or cover that provides access to the pilot light. In most cases, this will be positioned under the gas valve
  2. However, some water heaters will just have an open gap where you can see the pilot light burner instead. Locate the burner within the container using a flashlight or a headlamp. It will be reached by two little gas tubes. You’ll want to keep an eye on it while you’re at work. Turn the gas knob to the “Pilot” position and push and hold the button. This will initiate the flow of gas, allowing you to ignite the flame. Some water heaters feature a separate pilot mode button, which is commonly a red button, which you must push and hold in order to activate it. While keeping the gas pedal depressed, ignite the pilot light. Certain water heaters feature an igniting button that is red or black, while others must be lighted manually with a long lighter
  3. Some models include a red or black igniting button. Maintaining pressure on the gas knob or button for a full minute after the flame is ignited is critical. Then slowly release it while checking to see if the light is still on. Turn the gas knob to the “On” position and listen for the unmistakable “whump” or whooshing sounds that indicates the main burner has ignited. Enjoy your hot shower when you’ve replaced the lid.

Despite the fact that a single extinguished pilot light is normally caused by a natural fluctuation in gas pressure, recurrent faults suggest a more serious problem with the water heater itself. The most typical problem that causes repeated pilot outages is a filthy or bent thermocouple, which is a thin copper wire and rod that detects the presence of a flame and immediately switches the gas off when it detects a lack of flame detection.

What is a Thermocouple?

Though a single extinguished pilot light is normally caused by a natural fluctuation in gas pressure, a series of faults indicates a more serious problem with the water heating system. One of the most prevalent issues that causes repeated pilot outages is a filthy or bent thermocouple, which is a thin copper wire and rod that detects the presence of a flame and immediately switches the gas off when it detects an absence of flame.

How To Relight the Pilot Light in Your Gas Hot Water Heater

When the hotwater heater in your home fails, duties such as showering, doing laundry, cleaning dishes, and other household chores come to a grinding halt. If you have a gas-powered hot water heater, it is possible that the pilot light has gone out, which is the root cause of the problem. In most circumstances, if you relight the pilot, you should be able to go back into the air again. In this post, we’ll demonstrate how simple it is to complete the task yourself.

What does the pilot light do?

The pilot light of your gas hot water heater is a tiny, continuously burning flame that serves to start the burner of the appliance. To put it another way, if the pilot light goes out, the unit will be unable to heat water. It is possible for a pilot light to be extinguished for a variety of causes, including something as simple as a short stoppage in the gas line or an air bubble in the gas line. Warning: If you smell gas at any stage throughout the process, leave the area immediately and contact your energy supplier as soon as possible.

Steps to relight the pilot light.

  1. Remove your foot from the gas pedal. Find the gas shut-off valve on your hot water heater and turn it off. The knob should be labeled in a clear and understandable manner. Turn the switch to the “Off” position and wait 5-10 minutes to ensure that all of the gas has been expelled. Locate the pilot light access point. Most of the time, this will be under the gas valve. To locate the burner and two gas tubes, open the pilot cover (if one is present) and use a flashlight to peer inside the hole to locate the burner and two gas tubes
  2. Return to the gas valve and turn the knob to the “Pilot” position. By depressing the knob all the way down, you will begin to feed gas to the pilot. There are certain hot water heaters that include a separate pilot button
  3. If this is the case, press that instead. While maintaining control of the knob or button, reach into the access and ignite the pilot with an extended lighter while still keeping it down. Once the pilot light comes on, keep the knob/button down for about one minute. Release the knob/button carefully after that period of time, and make sure that there is still a flame emanating from the pilot. Return to the gas valve and turn the knob to the “On” position. Typically, a noise will be heard to indicate that the primary burner is lighting
  4. After giving the heater enough time to restart, replace the access cover and inspect the hot water supply.

What happens if the pilot light goes out again?

The fact that the pilot won’t light or that it keeps going out is a clue that you may be experiencing another problem with your hot water heating system. The most typical issue we encounter is a thermocouple that is twisted, fractured, or filthy (also called a flame sensor). Because the typical service life of a hot water heater is 12-15 years, it may be a wiser investment in some situations to replace the unit rather than spend money fixing your existing unit.

if your water heater isn’t producing enough heat, call Reidelt Plumbing Inc. at (219) 322-4906 for assistance. Our professional plumbers will come out to your home, assess the situation, and provide recommendations on how to restore hot water flow in your home.

  • This entry was published on April 30, 2020, under the category Water Heaters.

How to Light a Water Heater’s Pilot Light (With Pictures)

With 23 years of experience in the HVAC sector, Dan has gained knowledge in a variety of areas, including installation, service, sales, and distribution. Some individuals may think that lighting the pilot on a hot water tank is an easy chore, but as a home service provider for over 15 years, I can assure you that I’ve made more than a few dollars executing this task for others. Despite the fact that many modern gas-burning appliances have converted over to hot surface or electronic ignition, there are still a significant number of standing pilot systems being made and used today.

It will be explained in detail in the following stages how to light your pilot, what to watch for when doing so, and a few other techniques you may use to get the fire started.

Author’s Qualifications

  • 15 years of experience in HVAC installation and service
  • 5 years of experience as a home improvement contractor
  • Product safety, performance, and certification testing experience spanning more than two years
  • EPAOSHA certification. Electrical theory, thermodynamics, and refrigeration coursework have been completed

This is an illustration of what a sealed combustion chamber on this sort of device may look like. It’s your looking glass, which is represented by this small square on the panel. Take note of the differences between this sort of control module and the earlier tank-style control module. In addition to being a control, the little knob on top serves as a button. View from above in order to notice the electrical spark button to the left.

Lighting a Sealed Combustion Pilot

For the sake of illustration, consider the following image of a sealed combustion chamber on this sort of unit: It is your looking glass, which is represented by this small square on the panel. Make a note of the differences between this sort of control module and the earlier tank-style control modules. In addition to serving as a control, the little knob on top also functions as a button View from above in order to notice the electrical spark button to your left.

  1. Set the gas control knob on the top of the stove to the “pilot” position. To enable gas to flow, press and hold down the control knob itself for many seconds. Press and hold the electronic spark button, which is placed on or attached to your control module, until you hear it click. If there is a little amount of air in the line and it takes a few seconds to “bleed out,” you may need to click it a few times before the pilot is lighted. Continue to hold down the knob until the pilot has heated the thermocouple enough for it to be able to confirm ignition with the thermostat in the control module by visual confirmation. If the thermocouple does not heat up sufficiently, the pilot will be forced to return to the aircraft. Remove your finger from the control knob and visually check that the pilot is still glowing. To turn on the gas, turn the gas control knob to the “on” position. If the pilot was left out long enough for the water temperature to decrease, the burners should begin to operate within seconds of the pilot being turned off. If the water has not cooled, it is possible that there will be no need for the burners to be turned on. Be prepared for it to not start up immediately
  2. This is normal.

Make sure the gas control knob is in the “pilot” position on the top of the stove. To enable gas to flow, press and hold down the control knob itself. When you hear a click, press the electronic spark button, which should be on or affixed to your control module. If there is a little amount of air in the line and it takes a few seconds to “bleed out,” you may have to click it a few times before the pilot is lighted. Visually check ignition and maintain control of the knob for about 30-45 seconds to allow the pilot to heat the thermocouple sufficiently to confirm ignition to the thermostat in the control module.

After releasing the control knob, visually inspect the pilot to ensure that it has remained illuminated.

There may not be a need for the burners to turn on if the water has not cooled.

Lighting an Open Combustion Pilot

Unlike the sealed combustion tank, you will be required to provide your own flame to light the pilot, rather than relying on an electronic ignition to do so for you.

This process is very similar to the sealed combustion tank, with the exception that you will be required to provide your own flame to light the pilot yourself.

  1. The gas control knob should be set to pilot mode so that the notch in the dial corresponds to the button that controls the gas supply. If you do this, you’ll be able to press the button all the way down when it’s necessary
  2. Remove the panels from the burner compartments. Both should be quite simple to remove by raising up and pulling out. Place your preferred flame source (lighter, match, or other similar item) into the chamber such that the flame is directly beneath the aperture of the pilot supply line and ignite the flame. NOTE: I prefer to do three and then four. Despite the fact that the two stages can be exchanged, I believe it is better to introduce the flame before providing gas in order to minimize even the slightest possibility of gas buildup. I prefer to err on the side of caution, so I press and hold down the pilot gas supply button for many seconds before visually confirming that the pilot has been ignited. Keep the pilot gas supply button depressed for about 30-45 seconds to heat the thermocouple if this is the case. Release the button and visually check that the pilot light has not been extinguished. Assuming the pilot light remained on, turn the gas control knob to the “on” position.

Again, depending on your conditions, the water heater’s burners may or may not turn on straight immediately, so be patient.

Things You Can Use to Light a Pilot Light

  • A long, thin candle
  • A long, thin lighter
  • Long, thin matches
  • Short matches with a Hemostatic Clamp
  • A long, thin candle

Don’t Have a Lighter or Matches?

Lighting a long, thin candle on the stove and utilizing it to light the pilot light may be an option. When doing this, place a piece of tin foil behind the pilot to prevent wax from spilling onto the bottom of the chamber.

A Quick Water Heater Inspection You Can Do

  • Check for moisture and corrosion in the surrounding area and at the bottom of the unit (a.k.a. blisters). This might be a signal to be ready for a new tank
  • For example, Check to ensure that your T P valve is operational. Feel the tank in your hands. Is it comfortable? If this is the case, you may want to consider adding an additional layer of insulation. Check the operation of your thermostat control. You may accomplish this by reducing the heat down to the lowest setting and turning off the burners, if any are already operating. It is expected that the burners will shut down at this point and that they will re-ignite within seconds of turning the burners back on. If not, your control may be inadequate, and you should seek professional assistance. Final question: “When was the last time I cleansed my water heater?” You may wish to ask yourself this question. This is something that should be done at least once a year.

To the best of the author’s knowledge, the information in this article is accurate and complete. Content is provided solely for informative and entertainment reasons and should not be relied upon as a substitute for personal counsel or professional guidance in commercial, financial, legal, or technical problems, unless otherwise specified. Dan Reed was born in the year 2012. Dan Reed (author) wrote the following on April 22, 2012: Thank you so much, Mmargie. People who have never done it before may be nervous, but I always spend a significant amount of time thinking about my directions and selecting themes that are safe for anybody to try if the instructions are followed.

I’ve always been apprehensive about using gas appliances.

lolI feel a little better after reading the particular instructions on your site, despite the fact that I do not currently have any gas appliances.

How to Light the Pilot for a Gas Hot Water Heater

When the water in the tank needs to be heated, tank-type gas water heaters utilize a pilot light to ignite the gas burner, which then heats the water. The cold water flowing from the hot water tap is usually the first sign that your pilot light has gone out, so keep an eye out for it. Even if the equipment is not malfunctioning, a pilot light might go out for a variety of causes, including sudden swings in gas main pressure. If the pilot light on your heater goes out, you may relight it by yourself.

1.

  • Find the gas regulator valve on the water heater and turn it on. It is positioned on the exterior of the water heater, near where the gas line enters the device, and it is controlled by a knob on the outside. The gas supply to the pilot burner beneath the hot water tank is controlled by this valve. To turn the valve off, turn the knob all the way to the left. Wait five minutes before continuing. Locate the pilot burner, which is located beneath the natural gas water heater. Remove or unsnap any access cover that is preventing you from getting to the burner. Make use of the flashlight to illuminate the pilot burner

2.

  • Turn the knob on the gas regulator valve to “Pilot,” press down on it, and keep it pressed down. The flow of gas to the pilot burner is initiated by pressing this button. To start the pilot burner gas flow on some water heater types, you must push and hold down a separate red button for a period of time. Find a red or black button labeled “Ignition” on the top or side of the gas valve if your heater has a piezoelectric spark pilot igniter built in. To start the pilot, press the button on the control panel. As the igniter ignites, you will hear a click sound. If you must manually ignite your heater, a long-necked barbeque lighter is the most secure type of lighter to use. Light the pilot burner with a lighter flame and turn it on.

3.

After the pilot has been ignited, keep the regulator valve knob firmly depressed for at least one minute. This permits the pilot flame to heat the thermocouple safety sensor, which detects the presence of a live pilot flame, allowing the pilot flame to heat the sensor. Reduce the pressure on the regulator valve knob gradually. When the pilot light continues to glow after you have released the knob, turn the knob to the “On” position. During the ignition of the primary burner, you should hear a muffled “whoomp” sound.

Things You Will Need

Look for a label on your gas water heater that provides particular pilot lighting instructions for the model of water heater you have installed.

See also:  How To Turn On Pilot On Water Heater

Warning

  1. If you smell gas in the vicinity, it is not a good idea to attempt to relight a water heater pilot light (or to do any other maintenance on the device). When you are outside the home, dial 9-1-1.

How to light a gas water heater

If your water heater is not heating up, it is possible that the pilot light has gone out. No matter what sort of water heater you have, the process of lighting it is straightforward. The majority of contemporary versions of gas water heaters are equipped with a straightforward ignition switch.

The water heater is turned on in a matter of seconds, no trouble. If you’ve moved into an older home, on the other hand, it’s possible that your water heater is the type that requires manual activation. Here’s how to turn on both types of water heaters at the same time.

Do you have a manual water heater?

A blown pilot light on your water heater may be the blame for water not heating up properly. Whatever model you have, lighting a water heater is straightforward. Modern gas water heaters include a straightforward ignition switch that is easy to use. Easy as pie, the water heater may be turned on in a matter of minutes! Alternatively, if you’ve moved into an older home, it’s possible that your water heater requires manual activation. Listed below are the instructions for lighting both types of water heaters.

How to light an automatic water heater

If your water heater isn’t heating up, it’s possible that the pilot light has gone out. No matter what sort of water heater you have, the process of lighting it is easy. The majority of contemporary versions of gas water heaters have a straightforward ignition switch. It takes only a few steps to turn on the water heater, and it works perfectly. If you’ve moved into an older home, on the other hand, it’s possible that you’ll have a water heater that has to be turned on manually. How to ignite both types of water heaters is outlined below.

How to light a manual water heater

To fire this style of water heater, I recommend using a long barbeque lighter like this one. In any other case, getting in touch with the pilot will be difficult. To begin, remove the plate that is located beneath the dial-equipped box on the side of the water heater. There may also be an inner plate that you will need to shift to the side in order to complete the installation. Following that, you should notice a pipe or pipes heading to a burner. Then, in the box labeledOn/Off/PilotpastPilot, turn the knob to the Off position until it is completely off.

  1. Turn the water temperature dial to the lowest setting and the On/Off/Pilot dial to the Pilot position.
  2. Hold the barbeque lighter over the end of the pipe near the burner for a few seconds.
  3. Continue to press thePilotdial downward for about 30 seconds, after which move the dial fromPilottoOn.
  4. Important: If the burner does not come to life within a few seconds, repeat the operation until the burner does.
  5. Is the energy efficiency of your home high?
  6. CNET’s Guide to Smart Livingis a one-stop shop for tips, techniques, and how-to guides that can help you live a more intelligent life.

How to Relight Your Water Heater Pilot Light (For Every Major Brand!)

The pilot light on your hot water heater has great influence on your life. Anyone who has walked into their shower on a frigid winter morning, with their body freezing and their teeth chattering as they wait for hot water that never arrives, knows what I’m talking about. In the case of a natural gas water heater, this might indicate one of two problems.

There are two possibilities: either (1) the gas supply has been switched off or (2) your pilot light has gone out. We should first address the likelihood that your gas supply has been interrupted (and as fast as possible).

1. How to Make Sure Your Gas Supply is On

  1. Locate the shut-off valve for your natural gas line
  2. It is common to find the shut-off valve near to your gas meter (as shown in the figure below), which is often positioned on the side or front of your home or major structure. Check to be that the shut-off valve attached to your gas line is in the “ON” position before proceeding. If it is not in the ON position, the problem is not with your gas line
  3. However, if it is, the problem is with your gas line. If the valve is currently in the OFF position, switch it to the ON position. Please do not hesitate to contact your local gas company for assistance.

Examining your gas line is the first step in determining whether or not you have a lack of hot water. Double-check to see that the gas shut-off valve is in the “ON” position. If everything is in working order with your gas supply, it’s time to check the pilot light on your water heater.

2. How to Light Your Pilot Light Water Heater

Depending on the manufacturer, re-igniting a pilot light may need a different procedure. Fortunately, there are just a few number of producers. The first step should be to check for the installation instructions, which are normally fastened to the water heater. Don’t be concerned if you can’t locate them. Specific brand-by-brand instructions are provided in the section below. Instructions in this video are “generalized,” as the title indicates. Scroll down to the bottom of this page for instructions unique to your brand of water heater.

How to Light a Rheem Hot Water Heater Pilot Light

The pilot light on an ARheem water heater must be manually activated by striking thepiezo ignitor striker that is incorporated within the water heater.

  1. Using a clockwise motion, turn the gas knob on your Rheem water heater until it is at the desired position
  2. Counter-clockwise turn the temperature dial on the water heater until it is set to the lowest temperature setting. Wait five minutes to let any gas in the water to pass through
  3. Remove the outer door of your Rheem water heater from its mounting bracket. Counter-clockwise turn the gas knob to the “Pilot Light” setting until it is in this position. Press the red button to the left of the gas knob until it becomes depressed. The piezo ignitor striker is located on the left side of the gas knob. While maintaining pressure on the red button, continually push the piezo ignitor striker until the pilot light is re-lit until the problem is resolved. Through the viewing glass on the inside of the Rheem water heater’s inner door, you can see the pilot light. After the pilot light has been turned on, continue to hold down the red button for one minute before releasing it completely. The pilot light will remain on during the process. Remove and reattach the outer door of your water heater
  4. To turn on the gas, turn the knob to the “ON” position. Set the hot water temperature slider to the temperature that you desire for your water

How to Light an A.O. Smith or State Water Heater Pilot Light

AO Smith water heaters andState water heaters, including the Conservationist model, are equipped with a piezoelectric igniter mechanism that lets you to light the pilot by pressing the ignition button on the water heater.

  1. Disconnect the access panel from the side of the A.O. Smith or State water heater and place it somewhere out of the way
  2. To turn off the gas supply, turn the control knob on the water heater’s side to the “OFF” position and let the room air out for roughly 10 minutes. The “Pilot Light” setting on the gas control knob should be selected. The red button should be pressed down (this will allow the gas to flow to the burner assembly)
  3. And While maintaining pressure on the red button, press down on the ignitor button until the pilot light illuminates. It is possible that you may have to press down on the ignitor button two or three times before the hot water heater pilot light turns back on. Continue to hold down the red button for approximately 60 seconds after the pilot is lighted, then gently release the button. Make sure the gas is turned on by turning the control knob to “ON.” Replacing the access panel on the side of the water heater is necessary.

How to Light a Bradford White Water Heater Pilot Light

  1. Control panel for the Bradford White water heater should be turned off
  2. Allow the water heater to stand for 5 minutes to allow gas to escape from the system. Change the mode of the control switch to pilot light mode. Press the red control button in for a few seconds, then press the button every few seconds while continuing to press in
  3. Listen for a click, and the water heater status light should begin flashing to indicate that the water heater is operational. Allowing the red control button to be released
  4. Make sure that the red control button is in the “hot” position. If the pilot light does not stay lighted or does not relight after being extinguished, it is possible that a more serious problem is causing your lack of hot water. For emergency assistance, contact your plumber.

Resources

  • Precautions to take when using a water heater
  • How to get hot water back from your water heater
  • The components of a water heater
  • Water heater maintenance and repairs
  • What is the average lifespan of a water heater?

Call 1-Tom-Plumber

It might be rather frightening to experiment with the gas in your house. Don’t be concerned, we’ll have you back in a warm shower in no time! Please do not hesitate to contact us or call 1-Tom-Plumber (1-866-758-6237). Regardless of the nature of the emergency plumbing, drainage cleaning and drain clearing, or water damage situation, we will respond quickly. This includes excavation of subterranean water pipes and sewage main lines.

Why Your Water Heater’s Pilot Light Keeps Going Out & How to Fix It

The date is May 13, 2021. When the pilot light flame on your gas water heater goes out, it is an annoying and frustrating situation to have to deal with. When your water heater’s pilot light fails to stay lit, you’re left without hot water, which makes even the most basic of tasks such as taking a shower a chore. Naturally, you question, “How did this happen? What happened?” Is there anything you can recommend to help you get things going again? What should I do to have it repaired? “May you tell me about the costs I can expect?” Fortunately, if your water heater pilot light goes out, you should be aware that this is a frequent problem that many homeowners have and that the time and effort required to repair it is low.

Why does the pilot light on my water heater keep going out?

Because of problems with the heater’s thermocouple or owing to access to combustible air, your water heater’s pilot light continues going out repeatedly.

Thermocouple Issues

When your pilot light is on, your thermocouple detects the presence of the flame. The thermocouple’s tip is positioned above the pilot flame, providing a voltage that maintains the gas valve open in the process. A thermocouple will shut down the gas supply to your water heater if it detects that the pilot light on your water heater is not lighting up properly.

When thermocouples are exposed to moisture or dust for an extended period of time, they might malfunction, gather dust, or get bent away from the pilot light’s flame. In either situation, the thermocouple will have a difficult time sensing the pilot light and shutting down the gas flow.

Lack of Combustible Air

Another reason why your gas water heaterpilot light won’t remain lighted might be that there isn’t enough combustible air in the room where it is located. To keep the pilot light on in your water heater, you’ll need to blow air into it. Otherwise, the flame will be extinguished. Take precautionary measures to ensure that the water heater is not surrounded by material, such as litter or lint, which might increase the quantity of combustible air present. Maintain as much cleanliness as possible in the surrounding region.

What do I do if my water heater pilot light keeps going out?

Try to rekindle the spark on your own first, if at all possible. Take the following general steps:

  1. Locate the gas shut-off knob and turn it all the way to the “Off” position. The gas flow is halted as a result of this. Allow for a few minutes for the gas to dissipate before continuing. To get access to the burner, remove the access panel. To begin the flow of gas, turn the knob to the “Pilot” position. You’ll want to press and hold the knob down for a few seconds. While still holding the gas knob, ignite the pilot with a long lighter while still holding the gas knob. To ignite your gas water heater, use the button on the side of the tank that says “ignite.” As soon as the flames have been extinguished, turn the gas knob to the “On” position and wait for the main burner to come on.

If you are unable to relight the pilot or if your pilot light keeps going out, it is possible that you have another problem, such as a faulty thermocouple, to consider. Please refer to the owner’s handbook for your water heater equipment for further information.

Can I replace a thermocouple myself?

Yes. In the event that you are handy with tools, you may be able to change the thermocouple yourself. It is easier to accomplish this by turning off the gas valve and removing the entire burner and thermocouple assembly. In the case of minor repairs, it is preferable and safer to hire someone who is knowledgeable in the field of repair. A specialist may also evaluate your water heater for other faults and provide advise or ideas on how to deal with any existing or future difficulties that may arise.

Call BGE HOME

Please contact BGE HOME at (410) 918-5600 if your water heater pilot light will not light or continues going out. You may also contact us online. Our licensed specialists are available 24 hours a day, seven days a week to come out and inspect your water heater and make recommendations on how to get it running safely and effectively again. This item was posted on Thursday, May 13th, 2021 at 4:09 pm and is filed under Uncategorized. Commenting and pinging are temporarily closed for this post.

How to Relight Your Water Heater’s Pilot Light

Please contact BGE HOME at (410) 918-5600 or via our website if your water heater pilot light will not light or continues going out. No matter what time of day or night, our licensed specialists are available to come out and inspect your water heater in order to offer the most cost-effective and safest solution. At 4:09 p.m. on May 13, 2021, this entry was uploaded on the web. At this time, both comments and pings are closed.

  • Step 1: Turn off the gas
  • Step 2: Put the controls in “pilot mode.” Step 3: Press the control button and the light button simultaneously. Step 4: Bring the water temperature back to normal. Step 5: Reinstall the lid.

Don’t freak out if you find yourself without hot water for no apparent reason. It’s possible that the pilot light on your gas water heater has gone out. Despite the fact that this little blue flame should always be burning, it can go out for a variety of reasons. The good news is that, in the majority of situations, relighting is a simple process. This Might Also Be of Interest to You: Using These 5 Simple Steps, You Can Relight Your Furnace Pilot Light Please see the following steps for relighting the pilot light on your gas water heater.

How Do I Know If My Pilot Light Is Out?

In the event that you turn on a faucet and the water comes out cold, no matter how long you let it run, it is likely that your pilot light is out. You’ll need to get to the water heater in order to examine it. Most water heaters have a pilot light that is situated at the bottom of the machine, below the gas control valve, which makes it easy to find.

Look into the burner chamber by opening the access panel or entrance to the chamber. The pilot light tube may be found in this location, and it should have a continuous blue flame. If you do not see a flame, this indicates that the pilot light has gone out.

Can I Relight the Pilot Light by Myself?

In many circumstances, you will be able to relight the pilot light on your water heater by yourself. First, check sure there isn’t a gas leak in the area where you’re trying to relight the pilot light. Usually, a simple whiff will suffice to do this. Natural gas is usually scented by the utility companies in order to make it easier to discover leaks in your house. Most of the time, the scent is comparable to that of garlic or rotten eggs. If you suspect that you are smelling gas, do not attempt to relight the pilot light.

For further information, contact your natural gas utility.

Gas hissing and blowing noises may also signal the presence of a gas leak.

Additional Related Articles:

  • Here is an estimate of how much it will cost to replace a water heater: When your water heater isn’t working, you’ll notice these seven tell-tale signs. Learn how to properly drain a water heater. What is a Smart Water Heater and how does it work? I’m wondering how much a tankless water heater will set you back.
See also:  How To Turn On Hot Water Heater In Camper

What Do You Do When the Pilot Light Goes Out?

Re-lighting the pilot light according to the manufacturer’s instructions for your equipment should be attempted if at all possible. The procedure, on the other hand, is very consistent across different kinds of gas water heaters. To begin, establish if your water heater is equipped with an automated or manual ignition system. A glimpse at the control dial should be enough to notify you, according to Mullen Plumbing, Heating, and Cooling of West Virginia. If you have an automated igniter, it is likely that you have an ignition button.

It will be necessary to manually relight your pilot light.

How to Light a Pilot Light on a Water Heater Without an Automatic Igniter

  1. Using the access cover, switch the gas control valve to the “off” position to cut off the gas supply. Allow about 10 minutes for any gas that has gathered to disperse. The “pilot” position is reached by turning both the control and the water temperature knobs. To activate the control knob, depress it. To re-ignite the pilot light, hold the button down while using a wand lighter or long match to ignite it. A continuous flame should be visible once the pilot light has been turned on. For a full minute, continue to keep the knob down to force air out of the line that has accumulated over the course of time. Turn the knob to the left
  2. Set the temperature of your water heater back to the appropriate level by turning the control knob. Remove the access cover and replace it.

How to Light a Pilot Light on a Water Heater With an Automatic Igniter

  1. Remove the access cover from the door. To turn off the gas, turn the gas control valve to its “off” position. Wait about 10 minutes for the gas to disperse before continuing. Then, set the control and water temperature knobs to the “pilot mode.” To use the control button, press it. While maintaining pressure on the trigger, continually push the striker knob for approximately 90 seconds, or until the pilot is lighted. The striker knob is usually either black or red in color. Continue to hold down the control knob for a full minute to bleed air from the line, then release it.
  2. Set the temperature of your water heater by turning the control knob to the appropriate setting
  3. Replace the access cover in a safe manner.

Your pilot light should remain bright if it was accidentally turned off due to a draft or similar one-time problem. If it doesn’t work the first time, wait 10 minutes before attempting to ignite it yourself again after that. Having trouble with your water heater’s pilot light? It’s possible that your device requires expert maintenance or repair. Because we are spending more time at home than ever before, it is critical to be prepared for unexpected home repairs with a plan from HomeServe. The knowledge that you can easily call our 24-hour repair hotline in the event of a covered breakdown provides you more peace of mind.

Step by Step Guide: How to Light a Water Heater

Get your hot water heater up and operating in a safe and efficient manner. Get quotations from as many as three professionals! Enter your zip code below to get matched with top-rated professionals in your area. You should examine your hot water heater first if your hot shower has turned into freezing rain after you have turned on the hot water. Homes using gas water heaters should check their pilot lights to be sure they haven’t been turned off accidentally. The age of your heater may determine whether or not you may use an ignition button or a lighter to relight the pilot light on it.

The following tools and materials will be required:

How to Relight a Gas Water Heater’s Pilot Light

To relight a hot water heater, just follow the instructions outlined in the following section.

1. Safety First

Even though the vast majority of homeowners are capable of relighting a pilot light on their own, it’s crucial to use caution when working with a gas-powered hot water heater. When relighting a pilot light, you should always proceed with caution since the gas used to power your hot water heater is volatile and possibly deadly. If you smell gas at any time, you should turn off the gas valve immediately and open the windows to let the gas escape. Do not switch on any lights. Leave your home and call the gas company or the fire department for assistance.

2. Turn Off the Gas

First and foremost, you must switch off the gas supply before re-igniting the pilot light. Locate the gas valve on your hot water heater and turn it to the “off” position to turn the water off. Hold off for around 10 minutes; this will give any gas in the region time to clear, which is vital because the gas is very combustible, so patience is required.

3. Access the Pilot Light

It is customary for the pilot light to be situated directly beneath the gas valve. In certain circumstances, a door or cover may be placed over the light to prevent it from being seen. While you are doing this procedure, use a flashlight to ensure that you can see everything clearly and accurately.

4. Turn the Gas Valve to ‘Pilot’

Turn the gas valve to the “pilot” position and push the button. As a result, the gas valve provides enough gas to ignite the pilot light, which is what you want. If your hot water heater is equipped with a separate pilot button, this is something to look for.

5. Light the Pilot

Press down on the gas valve when it is set on “pilot.” Because of this, the gas valve is able to supply enough gas to ignite the pilot light. There is a possibility that your hot water heater will have its own pilot button.

6. Turn On the Gas

Once the pilot light has been lighted, re-ignite the gas supply.

7. Don’t Be Afraid to Ask a Professional

If you want assistance, consult with a local water heater technician, particularly if your hot water heater requires manual ignition. Most service providers will charge a set price every visit, which will normally cover the cost of relighting a gas water heater in the event that one is required. The cost of this service call might range between $80 and $100.

FAQs About Hot Water Heaters

Photograph by Hmzalldesign/iStock / Getty Images Plus courtesy of Getty Images If your water is barely lukewarm, it is possible that your hot water heater is malfunctioning. It might be a sign that your water heater is going to malfunction, that sediment has accumulated, or that the temperature has been adjusted improperly. In order to establish the specific nature of the problem, you need consult with a water heater repair professional.

How much does it cost to repair a hot water heater?

The cost of repairing a hot water heater can range from$225 to $960 depending on the model. The cost of repairing a water heater varies based on where you reside and what is wrong with it. In certain circumstances, it may be more cost effective to replace your hot water heater rather than repair it.

How do I maintain my water heater?

Some things you can do to keep your hot water heater in good working order include examining it on a regular basis and flushing it out of the tank.

How to Light a Hot Water Heater

There’s almost nothing worse than taking a cold shower, and if the pilot light on your hot water heater has gone out, that means it won’t be able to produce any hot water. Getting a pilot light on a water heater is a simple task that can be completed by the majority of individuals who don’t have much experience with the process. You should exercise caution if you have a faulty flame sensor since gas might be mistakenly discharged into the home if the sensor fails.

Lighting a Gas Water Heater in 7 Steps

Keeping in mind that each water heater is different and has its own set of instructions that you should follow, we’ve put together some generic directions on how to ignite a gas water heater for your convenience. Don’t forget that you can acquire all of your water heater components right here at PlumbersStock.

  1. Turn off the gas valve—for your own safety, find and shut off the gas shut-off valve. Now, go get yourself a sandwich since you will need to wait around 5 minutes before continuing
  2. Some tanks will have an open gap, most commonly beneath the gas valve, while other units may have a panel with a door that must be opened in order to access the pilot light. Search for and locate the burner- using a flashlight, locate the burner (which will have gas tubes running to and from it
  3. Be prepared to switch on pilot mode- there is either a gas knob or a button that will allow you to engage pilot mode, which will provide you with adequate gas flow to begin the piloting procedure. The process must be started when you’re ready to go on to step 5. Light the pilot at the same time as you initiate pilot mode—while you are in pilot mode, light the pilot. Manually lighting the burner with a hand lighter may be necessary, although many versions are equipped with an ignition button that will ignite the burner. To maintain pilot mode, continue to press the gas button/knob for a full minute, then release the button/knob and check to see whether the flame is still ignited on the burner. Switching on the gas valve should result in a very pleasing “whoosh” sound from the water heater, which happens when the main burner ignites.

Alternatively, if your water heater does have an access panel, simply replace the cover and you’re done. In case you’re interested in seeing a useful video lesson, check out this youtube entry by ehowhome:

Why Do Pilot Lights Go Out?

If your water heater does have an access panel, just remove it and replace it with a new cover. This ehowhome item on YouTube is a useful video instruction that you should check out.

  1. It is possible that you have an issue with the thermocouple. In layman’s terms, a thermocouple is a sensor that detects fire. Your thermocouple will not be able to perceive the flame if it is filthy, bent, or otherwise compromised. If it is bent, it is conceivable that you will be able to bend it back to where it should be in order for it to feel the flame. If something is filthy, it can be cleaned. In the event that it is damaged, it must be replaced. Follow the instructions in this article to learn how to replace the thermocouple. It’s possible that you have a grounded heating element. Sometimes the pilot light will not come on because the element will not turn off, even when the thermocouple is successfully turning off the water heater. Become familiar with the procedure for testing a heating element.

Water Heaters at PlumbersStock

You can contact us if you have any questions about your project or about parts and water heater accessories. We have everything you need to get your water heater up and running like new, so if you have any questions about your project or about parts and water heater accessories, please contact us. Have you considered a water heater that heats water on demand? Resources that are related to this topic include: How to Reset a Water Heater (with Pictures) How to Turn Off a Water Heater (with Pictures) Draining a Water Heater (with Pictures) Instructions on How to Turn On a Water Heater How to Increase the Temperature of a Water Heater Is there a recommended temperature for the water heater?

How to Relight the Pilot Light on Your Water Heater

Several factors might contribute to a pilot light on a water heater being turned off. The front of most water heaters will contain instructions on how to relight the pilot light, and this will usually be on the right side of the water heater. The first step is to turn off the gas to your water heater by turning off the gas control valve on the tank. Then follow these instructions to re-ignite the pilot light on your water heating system:

  1. Remove the access panel for the water heater
  2. Check to see if the gas valve is open (on most valves, this indicates that the valve is in line with the pipe)
  3. And Make sure that the gas control valve on the water heater is in the pilot position. Hold the knob on the front in and press it in. For a flame to emerge on the screen, hold down the ignitor button (the black square button below the knob). Keeping the knob pressed in until the indicator light starts blinking is recommended. Using the knob, adjust the temperature to your liking.

The flame should be visible via the viewing window if you look closely enough. That indicates that your pilot light has been turned on. Although the gas control valve on your water heater may be different, the process of relighting it should be very similar. You may look up “How to relight a _” on Google and fill in the blank with the name of the brand of your water heater to see what comes up. YouTube is another excellent source of information.

Gas control valves come in a variety of shapes and sizes, and they might be installed on your water heater. Some further how-to videos on relighting the pilot light on a water heater with different gas control valves may be found at the following links.

If you are unable to relight your pilot light, or if it does light but continues going out on you suddenly, contact a plumber you can trust for assistance in determining what is causing the problem. The 25th of August in the year 2021 All of the posts

How to relight a gas water heater pilot light

When one of our customers, Theresa, requested that we give some basic instructions on how to securely relight the pilot light on a gas water heater, we gladly obliged. Theresa, thank you for your proposal; we are pleased to assist you.

Step 1

The following instructions were requested by Theresa, one of our customers, on how to properly relight the pilot light on a gas water heater. Please accept our compliments for your proposal; we are delighted to assist you.

Step 2

Turn the gas valve to the “Pilot” position and depress the valve button (or, instead, if there is a red button beside the valve, push it down). Maintain pressure on the button to begin the flow of gas via the gas supply tube.

Step 3

Continue to press the button down and wait for the indication to light up on the screen. Some water heaters need the use of a manual light switch. If this is the case, fire the gas at the end of the supply tube using a grill lighter.

Step 4

Maintaining the hold on the control button for another minute or two after the pilot is lighted is recommended. Then press and hold the control button for a few seconds.

Step 5

Alternatively, if the pilot continues to glow after you remove the control button, set the dial to “on.” If the pilot goes out again or if the light does not come on, start over at Step 1 and repeat the procedure. It’s quite OK to give something a couple of tries. However, if your pilot won’t light or won’t stay lighted after a few of tries, it’s better to contact a professional for assistance.

Why Your Pilot Light Keeps Going Out & How To Fix [With Pictures]

That darn pilot light just won’t stay turned on! Moreover, it is causing all of your plans for today to be derailed. Nothing compares to the sensation of taking a hot water shower. However, there are times when this does not occur. After all, there are worse things than having a very cold bath, should we say? The one thing that everyone despises is a lack of running water. This may be incredibly inconvenient – not only for showering, but also for all of the other duties that require hot water to be completed successfully.

You don’t have to put your day on wait because your pilot light isn’t working properly.

However, if you discover that your water heater is leaking water and that this is the root of your water problem, read our guide on what to do when your water heater is leaking water!

What’s A Pilot Light?

I can’t seem to keep the pilot light on! You are unable to complete your tasks today because of this. When you step into a hot water shower, there’s nothing quite like it. In the event that this does not occur, however, Let’s just say that there are certain things that are worse than taking a cold bath. Everybody despises the fact that there is no hot water available at all times. This may be incredibly inconvenient – not only for showering, but also for all of the other duties that require hot water.

Because of an inconsistent pilot light, you don’t have to put your day on wait.

However, if you discover that your water heater is leaking water and that this is the root of your water problem, read our guide on what to do when your water heater is leaking water. A Professional Can Now Repair Your Pilot Light!

Appliances With Pilot Lights

Water heaters, older furnaces, and boilers are more likely to have a pilot light than other types of appliances. You may also discover that your gas fireplace has a pilot light, which is a good thing. Learn how to switch on the pilot light on your gas fireplace by visiting this page. Pilot lights have been gradually being phased out in favor of hot surface igniters or spark igniters in more recent years. pilot light for a water heater The pilotflame ignites the gas, which generates heat for your house or place of work.

See also:  How Much Is A Tankless Gas Water Heater

Also, if you are experiencing no heat, check to see whether the pilot light on your furnace or boiler has gone out.

Water Heater Pilot Light: Where Is It And What Does It Do?

A little access panel, located just underneath the thermostat, may be found at the very bottom of your gas water heater. The pilot light for the gas water heater is located within the access panel. There will be a gas panel where you may check to see if the pilot flame has been ignited. The pilot light on your water heater is a little flame that is used to ignite the gas burner in the water heater. This is required for the purpose of heating the water that will be dispersed around your home. If you are experiencing no hot water and have attempted to relight your pilot light without success, you will require water heater repair.

Warning!

This photograph was shot by a water heater professional for the purpose of giving a demonstration on the use of pilot lights.

What Makes Your Water Heater Pilot LightGo Out

Thermocouple on the water heater is faulty. The thermocouple is responsible for detecting whether your pilot light is on. This copper rod serves as a safety precaution, preventing the heater’s gas supply from being turned off if the pilot light on the water heater goes out. The natural wear and tear of a thermocouple can cause it to get twisted out of place, to malfunction, to become broken, to become covered in dirt, or to accumulate carbon deposits. When one or more of these conditions occurs, the thermocouple will be unable to reliably detect the pilot light and will subsequently shut down the heating system.

Strong Breeze Can Blow Out Pilot Light

In some cases, such as when there is heavy wind or a nearby draft, your pilot light may be extinguished. Unless your pilot light has simply been out, you should have little trouble re-igniting it and keeping the flame burning.

Kink in the Flex Tube

The fuel is delivered to the gas controller by flexible tubes. Gas will not flow through the tube if there is a kink or twist, which can also lead to pilot light difficulties.

Filthy Pilot Light OpeningCan MakePilot Light Keeps Going Out

If the pilot’s mouth is clogged with muck and debris, it will be virtually hard for it to maintain a flame. It will only keep a modest flame that will be readily extinguished if it does catch fire. Your pilot light will not stay lit if your pilot orifice is clogged with debris.

How Do I Re-Light My Gas Water Heater Pilot Light?

The pilot light on the water heater is not lighted.

Step 1: Thoroughly Read Gas Water Heater Manual

To have a better knowledge of where each component of your water heater is situated, consult your water heater’s instruction manual.

Step 2: Turn Down Thermostat

To have a better knowledge of where each component of your water heater is situated, consult your water heater handbook.

Step 3: Turn OFF Gas

The gas valve for the water heater Locate the gas shut-off valve and turn it all the way to the “Off” position. The gas shut off valve is positioned on the gas line near the base of your water heater, near the base of your water heater. Before proceeding on to the next stage, you must wait at least 5 minutes to guarantee that all of the gas has dissipated completely.

Step 4: After 5 Minutes, Turn The Gas Control Valve Setting On Water Heater To “Pilot”

Turn the gas control valve, which is situated on the water heater, to the “Pilot” position. The word “Pilot” should be in the center of the image.

Step 5: HoldDownthe Reset Button

Keep the water heater reset button depressed. After that, press and hold the reset button. This is a button that is often red in color and is situated to the left of the gas control valve. Keep your finger on this button. To be on the safe side, use the instructions to identify each component.

Step 6: While Holding Down The Reset Button, Press TheIgniter

Keep the water heater’s igniter down. The igniter is located to the right of the gas control valve. While continuing to keep the reset button down, press the igniter button on your keyboard. Click on the water heater’s gas window until you see a blue flame appear in the glass.

Step 7: Continue To Hold Down The Reset Button For 20-30 Seconds.

Following the sighting of a flame and the removal of your finger from the igniter, you must continue to press the reset button. Continue to hold the button down for another 20-30 seconds.

Step 8: Turn The Gas Control Valve To The “On” Setting

On the water heater, there is a gas control valve. The gas control valve may now be turned back to its “On” position, as the pilot light has been ignited by the flame. The word “on” should be in the middle slot at this point.

Step 9: Turn The Thermostat Up

Increase the temperature of the water heater. Now is the time to dial up the heat in order to get that hot water flowing again!

Step 10: Enjoy Your Warm Water, Or Ask For Help!

If you try to relight the pilot light and it does not stay lit, you may want the services of a professional to assist you with your water heater repair.

But What If You Don’t Have A Manual Igniter?

After that, remove the access panel that is located beneath the water heater thermostat and discard it. You can use a wrench to help you.

After 5 minutes, Turn Gas Control Valve To “Pilot”

After that, remove the access panel that is located beneath the water heater’s temperature control. Use a wrench to get the job done.

Next, Hold Gas Control Valve Down And Ignite Pilot With A Lighter

Keep the gas knob pressed down as you ignite the pilot using a long lighter, similar to a BBQ skewer. If your gas water heater, on the other hand, has an igniting button, use it instead.

Once TheFlame Is Lit,Turn Gas Control Valve to “On”

As soon as the pilot light is lighted, you may remove the reset button and turn the gas knob to the “On” position, which will take around 30 seconds. You should be able to hear the main burner turn on at this point. Your pilot light should now be able to maintain a flame, and hot water should be flowing again!

Furnace Pilot Light: Where It Is And What Does It Do?

Old furnaces rely heavily on the pilot light to generate heat, which is why it is so crucial to keep the pilot light on. When the gas valve is opened, the flame will continue to burn constantly, igniting the gas. The heat generated by this process then heats the air that is drawn into your furnace, which is then dispersed throughout your house. If your furnace’s pilot light is out, you may notice that it is spewing chilly air into the house. The failure of the pilot light is one of several probable causes of your furnace’s inability to switch on.

You may find the pilot light by following the gas line into your furnace and looking for it there.

From there, you should be able to see a short tube that runs from the gas valve to the burner itself. You should be able to locate the pilot light if you follow the little tube leading to it.

Why Furnace Pilot Light keeps going out

There are a variety of reasons why the pilot flame on your furnace continues flickering out of control. Let’s get started!

Faulty Thermocouple Triggers Pilot Light to Go Out

It is meant to shut off the gas valve if the pilot light goes out, and it is used in conjunction with a thermocouple. Thermocouples can be damaged or worn out over time. If the thermocouple is incorrectly positioned or malfunctioning, the gas valve may be incorrectly shut off, as well as preventing the pilot light from keeping lit.

Dirty Thermocouple Makes Pilot Light Keeps Going Out

A filthy thermocouple may cause the safety mechanism to mistakenly trigger, causing the ignition to be turned off. The thermocouple has the potential to accidentally shut off the gas valve and extinguish the blazing flame.

Filthy Pilot Port/Orifice

Examine the flame. If the flame is becoming orange, contact an HVAC professional immediately. If you light your pilot and the flame is yellow, this indicates that your pilot opening is filthy and is preventing your pilot light from keeping lit for long periods of time. A buildup of dirt in the pilot light port might prevent the flame from fully enveloping the thermocouple, which can result in a faulty ignition. As a result, the safety system is activated, which results in the gas being turned off.

Bad Gas Regulator

If you have gas appliances in your house, you will also have a gas regulator outside of your home to regulate the flow of gas into your home. Your furnace may not receive enough gas to keep its pilot light lit if your gas regulator isn’t functioning correctly. There is a good chance that you have a defective gas regulator if the pilot light is out in more than one home appliance, such as your water heater.

Bad Flue Venting Could Blow Out Pilot Light

Excess wind might enter via the openings in your flue pipe if it is loose, broken, or not correctly attached to the furnace. This would extinguish the pilot light flame.

A Strong Draft

There’s always the potential that a powerful draft knocked out your pilot light’s flame and caused it to go out.

How To Re-Light A Furnace Pilot Light?

You should never rule out the chance that a strong airflow was the cause of your pilot light being extinguished.

Step 2: Identify Pilot Light

Find the location of the pilot light in your furnace by consulting the owner’s handbook. In order to get access to the furnace, you will need to remove the front of the furnace.

Step 3: Turn OFF Gas

After that, locate the gas valve and shut it down completely. A tiny valve located towards the bottom of the furnace is standard on most models. In general, there are three settings for the gas valve: “ON,” “OFF,” and “PILOT.” Make sure the valve is in the “OFF” position by turning it clockwise. It is critical that you wait for at least 5 minutes after the previous step to ensure that all gas has been expelled from the pipes before proceeding. A disaster might occur if this is not done.

Step 4: WAIT 5 Minutes, then Turn Gas to “Pilot”

Immediately after waiting 5 minutes, switch the gas valve to the “PILOT” position.

It is vital that all of the gas has dissipated before switching the gas position to the pilot position. A few of minutes might be the difference between a peaceful society and a disasterous one. Keep in mind that gas is quite explosive!

Step 5: Hold Reset Button

Immediately after waiting 5 minutes, switch the gas valve to the “PILOT” setting. To ensure a smooth transition from pilot to gas, make sure all of the gas has been released. A few of minutes might be the difference between a peaceful society and a disasterous society. Never forget that gas is extremely dangerous.

Step 6: Press Igniter While Holding Reset Button

Holding the reset button down for a second or two will allow you to activate the igniter and light the flame. Once the flame has been ignited, remove the igniter and continue to hold down the reset button until the flame has been extinguished. Keep the reset button pushed for 20-30 seconds to complete the process. To light the pilot when you do not have a manual igniter, you can use a BBQ lighter or a match. furnace with a pilot light

Step 7: Turn Gas to “ON” position

Restore the pilot light by turning the gas control valve back to its “ON” position once it has been re-ignited. Right now, you should be able to keep your house warm!

Step 8: If you Aren’t comfortable yet, call a pro!

If, despite doing the necessary measures, you are still unable to keep your pilot light lit, contact an HVAC professional for furnace repair.

Boiler Pilot Light: Where It Is And What Does It Do?

The pilot light in your boiler is vital for the boiler to function properly and generate heat. It is necessary for the pilot to burn constantly in order for it to ignite the gas when the gas valve is opened. When this occurs, your boiler starts heating the water, which is subsequently dispersed throughout your house to provide warmth. If your pilot light goes out, your boiler and central heating will not be able to operate properly. The pilot light is placed within your boiler, on the other side of the valve from the gas valve.

Why Boiler Pilot Light Goes Out

A malfunctioning, misaligned, filthy, or damaged thermocouple is frequently the source of your pilot light’s failure to illuminate properly. It is the thermocouple that keeps the gas valve from opening if the pilot light is not lit. Your pilot light may not function properly if there is an issue with your thermocouple, or if it is just coated with dirt and debris.

Dirty Pilot Opening

When you turn on your furnace pilot light and find a yellow flame, this indicates that your pilot light is unclean and is causing your furnace pilot light to constantly turning out. If dirt accumulates in the pilot light port, it may prevent the pilot light from completely enveloping the thermocouple with the flame it produces. This causes the thermocouple safety system to be incorrectly activated, resulting in the gas being turned off and the heat being turned off.

Weak Gas Regulator Can Make Pilot Light Keeps Going Out

If you have gas appliances in your home, you will have a gas regulator outside your home. The failure of your gas regulator may result in your furnace not receiving enough gas to keep its pilot light lit. In the event that you observe pilot light issues on more than one device, such as your water heater, it is possible that your gas regulator is broken or weak.

A Strong Draft

A strong airflow has the potential to completely extinguish your pilot light.

How To Re-Light Boiler Pilot Light

Make sure you are familiar with the components of your boiler by reading the instruction manual thoroughly.

It is common for the owner’s handbook to contain instructions for re-igniting the pilot light.

Step 2: Shut OFF Boiler

Starting with shutting off the boiler is always a good idea.

Step 3. Shut OFF Gas

Locate the gas valve and turn it to the “OFF” position.

Step 4. Wait 10 Minutes

Continue to check the pipes for around 10 minutes to ensure there is no residual gas.

Step 5. Open Boiler and Locate Pilot Light

After a short period of time, you can turn on the boiler. To obtain access to the pilot light, remove the access panel from the wall. Typically, this panel is positioned next to the gas control knob box, which is where it gets its name. Sometimes you may simply lift the panel up, but other times it may be screwed to the wall or ceiling.

Step 6. Turn Gas to “Pilot”

Now, set the gas control valve to the “Pilot” position on the pilot valve.

Step 7. Hold Reset Button, Then Click Igniter

Next, press and hold the reset button for a few seconds. While still holding down the reset button, press and hold the igniter button until you see a flame appear. It is necessary to press the reset button for an additional 20-30 seconds after the flame is ignited to ensure that it is fully functional.

Step 8. Turn Gas Control Valve To “On” Setting

Restore the pilot light by turning the gas control valve back to its “ON” position once it has been re-ignited. Right now, you should be able to keep your house warm!

Step 9. Relax in Comfort

Turn the gas control valve back to the “ON” position once the pilot light has been re-lit. The heat in your house should be working immediately.

How Do I Prevent My Pilot Light From Going Out?

Keeping your water heater, furnace, and boiler in good working order can keep those annoying pilot lights from going out on you. An experienced technician will do a maintenance check on the pilot light and thermocouple, as well as clean them both, to ensure that they operate at peak efficiency. Depending on the appliance, a professional will also check all of the connected pipes and wiring, the flue venting, and all other functional aspects of the appliance to verify that each portion is running at peak efficiency.

Maintaining your furnace, water heater, and boiler on a regular basis is essential to ensuring that your heat or hot water never runs out!

Soak Up The Warmth!

That’s all there is to it! A basic description of how to relight your pilot light, as well as the most typical causes for your pilot light to go out is provided. We all know that having no heat or hot water in your house is the worst feeling in the world! The best course of action if you’re having difficulties keeping your pilot light lit or are still unclear about the process is to call a professional. If you are experiencing any pilot light issues, please don’t hesitate to contact us at (443) 219-7798 or make an appointment onlinehere.

Leave a Reply

Your email address will not be published.