Reset EcoSmart Tankless Water Heater [6 Error Codes Fixes]
EcoSmart is an excellent brand to consider when purchasing a tankless water heater. However, you will need to reset it on a regular basis. A common occurrence is that you’ll notice an error code shown on your water heater’s display, and your water heater will cease to work completely. If this is the case, you’ll need to conduct a reset on your EcoSmart water heater in order to resolve the issue and then restart it. Our discussion today will be on how to reset an EcoSmart Tankless water heater.
Because resetting the clock is only a temporary fix.
How To Reset EcoSmart Tankless Water Heater
Resetting the EcoSmart Tankless water heater is a straightforward process that anybody can complete. The following are the steps. Remove all of the hot water faucets from your home, starting with Step 1. Step 2: Disconnect your EcoSmart from the power source. If your tankless unit is equipped with a remote control, you may use it to turn it off. If this is the case, just depress the temperature control knob to turn the heater off. Step 3: Check to see that there is no electrical current flowing through the device by turning off the circuit breakers on the wall.
After that, you may switch on the device.
Other times, the water heater will run for a short period of time before displaying the problem signal once more.
Solutions To EcoSmart Error Codes That Require Heater To Be Reset
Fortunately, there aren’t many fault codes associated with the EcoSmart tankless water heaters. We’ll go through each and every one of them here.
01.E1 Error Code
Fortunately, there aren’t many fault codes associated with the EcoSmart tankless water heater. Each one will be discussed in detail below.
Solution:
For a brief period of time, there is a technique to get around this mistake. However, you’ll need to consult with a specialist in order to diagnose your inlet thermistor. You can receive hot water for the time being by following these steps:
- Turn on the water to the point where the LED display glows and the E1 error is shown. When you press and hold the round knob for 3/5 seconds before releasing it, you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that This is the moment at which your LED display should read CE1. Run the water for 2/3 minutes and check to see if there is any hot water
02.E2 Error Code
Make sure there is enough water flowing so that the LED display is illuminated and the E1 error is displayed. When you press and hold the round knob for 3/5 seconds before releasing it, you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying you It is at this stage that your LED display should read CE1.
Check for hot water after running the water for 2/3 minutes.
Solution:
For a brief period of time, there is a technique to get around this mistake. However, you will need to consult with a specialist in order to diagnose your outlet thermistor. You can receive hot water for the time being by following these steps:
- Turn on the water to the point where the LED display glows and the E2 error is shown. When you press and hold the round knob for 3/5 seconds before releasing it, you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that At this point, the CE2 indicator on your LED display should be shown. Run the water for 2/3 minutes and check to see if there is any hot water
03.E3 Error Code
A temperature error number of this type indicates that both the outlet and inlet thermistors in your device are not reading the right temperature and that they may need to be replaced.
Solution:
It is possible that you may need to replace both the outlet and inlet thermistors in order to resolve this problem. However, by following this quick technique, you will be able to temporarily skip the problem code.
- Turn on the water to the point where the LED display glows and the E3 error is shown. When you press and hold the round knob for 3/5 seconds before releasing it, you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that you are saying that This is the moment at which your LED display should read CE3
- Run the water for 2/3 minutes and check to see if there is any hot water
04.E4 Error Code
When the entering water temperature is 150 degrees or above, this problem code will be shown on the screen. This heater features two to four thermostats (depending on the kind), each of which has a temperature rating of 140 degrees Fahrenheit or higher. It is not intended to be used at temperatures exceeding 140 degrees Fahrenheit.
Solution:
Immediately lower the temperature of the entering water to less than 140 degrees Fahrenheit if your control board shows this error code. Once the machine gets water that is less than 150 degrees, the LED display will illuminate with the required set temperature.
05.E5 Error Code
If the E5 error code displays on the LED control board, it indicates that the intended volume of water is too large, and that the Flow rate must be reduced to compensate.
Solution:
Aerators are fitted in each sink, shower, and tub to help control the flow of water in the bathroom. The following should be the range of flow rates to be used.
- Sinks have a flow rate of 1 – 2.5 GPM (gallons per minute)
- Showers have a flow rate of 1.5 – 3 GPM
- Bathtubs have a flow rate of 3.5 – 8 GPM
- And washing machines have a flow rate of 1.5 – 2.5 GPM.
As a result, if the LED control board displays an E5 error, lower how much water is being circulated through the system until the LED display begins to read at the proper temperature. It is advised that you install a flow restrictor or partially close the incoming or departing water valves in order to do this. Flow restrictors are available from a variety of sources, including most hardware stores, internet retailers, and EcoSmart itself.
06.S103 Error Code
If the LED control board displays an S103 error code, it is possible that your device is not receiving the right amount of power from the system. This heater requires a voltage of at least 208 volts in order to function effectively.
Solution:
It is necessary to confirm that the water heater is receiving the proper voltage supply. Get in touch with your local electricity utility provider. As soon as the heater gets the appropriate amount of incoming electricity, the system’s LED screen will indicate the required temperature, and the water will begin to heat.
FAQ:
If your water heater reset button continues tripping, it’s possible that one of your heating components is malfunctioning or worn out. If the reset button on a water heater thermostat continues to trip, it is possible that the metal case surrounding the heating element has fractured.
How long should a tankless water heater last?
The vast majority of tankless water heaters have a lifespan of more than 20 years, on average.
They also include easily replaceable components, which allows them to survive for many more years. Storage water heaters, on the other hand, have a life expectancy of 10 to 15 years.
Do you have to drain your water heater once a year?
It is possible to expect a tankless water heater to last 20 years or longer. Moreover, they have easily replaceable components, allowing them to last for many more years. Storage water heaters, on the other hand, have a life expectancy of 10–15 years or longer.
How long does it take to flush a water heater?
In most cases, a tankless water heater has a lifespan of more than 20 years. They also have readily replaceable components, which allows them to survive for many more years. Storage water heaters, on the other hand, have a life expectancy of 10–15 years.
Why is my hot water discolored?
The most common source of colored hot water is sediment and mineral build-up inside the heater, which is probably the most common reason. This problem is most commonly resolved by flushing the water heater’s tank with a chemical solution.
Conclusion
After you’ve taken care of the error code and reset your heater, your heater should be back to its usual operating condition. Depending on the error code you’re encountering, the intricacy of the problem, and the duration of the problem, you may need to seek expert assistance. Hopefully, your water heater will be up and running within minutes. Take advantage of the hot showers!
Resetting EcoSmart Tankless Water Heaters (Fully Explained)
The most recent update was made on November 19th, 2021. Modern tankless water heaters have shown to be an extremely convenient addition to a wide range of home situations. It takes up less room and requires less upkeep. As a result, it is becoming increasingly popular as an alternative to traditional water heaters. EcoSmart tankless water heaters are the same as any other tankless or traditional tank water heater in terms of performance. They are nonetheless prone to malfunctions in spite of this.
This article discusses how to properly take care of your EcoSmart.
Several new tankless water heater types have been introduced recently, including those from EcoSmart in particular.
The sizes, uses, and energy efficiency of the options are all different.
EchoSmart Tankless Water Heater Reset Button
Some electric tankless water heaters feature a reset button on the side of the unit. In addition, it serves a very vital function. Malfunctions and possible electrical concerns might develop from time to time. As a safety measure, the reset button may trip and cause the machine to shut down as a feature. In such instance, the reset button effectively functions as an internal circuit breaker. It is a safety feature that keeps your water heater from sustaining additional harm. A significant electrical threat that may endanger you or your family is also prevented by this device.
Just make sure it isn’t the result of a lack of maintenance or careless handling of the unit before proceeding.
So, what is the best way to reset your EcoSmart?
If the device is not turning on, it is possible that a malfunction or a power surge occurred, which caused the fuse to blow. The problem can be resolved by changing the fuse. The unit can then be reset at that point.
Cleaning An EcoSmart Tankless Heating Unit
Cleaning an EcoSmart water heater is not a time-consuming endeavor. However, there are several processes involved. The cleaning process is divided into three parts, which are detailed below.
Preliminary Steps
- Turning off the device is the first step. After that, turn off the tankless water heater’s circuit breakers by pressing the power button. Make certain you complete the next step. This assures that there is no electric current present that might electrocute you at any point in time. After that, turn off the water intake valve or shut off the main water supply. After that, turn on a hot water faucet in your home. This will completely drain any remaining hot water from the tankless device. Additionally, hot water will not scorch you after the hoses are disconnected. Close the outlet valve that is connected to the hot water output of the unit when that is done. As a precaution, loosen both the intake and output hoses from their respective valves. This will prevent any hot water from backflowing from the pipe when the hose is removed. They connect the unit’s intake and outlet water lines together
- These hoses are flexible. After that, remove the front cover of your tankless water heater. This will need you to remove four screws, and then you will need to unscrew the wires that are linked to the heating element. The majority of tankless water heaters include more than one heating element. The heating components may be placed in a variety of locations. This is dependent on the individual EcoSmart model you have. On bigger devices, the heating components are located vertically on the top left side. Heating elements on smaller units should be laid horizontally on top
- Then, unscrew the heating element in a counter-clockwise movement until it is completely removed. There will be some scale building on the copper tubing of the heating element, which you will notice.
Cleaning and Flushing
- Remove the flow resistor from the water line leading out of the unit. Then thoroughly clean it inside and out to remove any mineral flakes or scale buildups. After that, immerse the heating element’s pipes in vinegar for a few minutes. You may also utilize a descaling method to help with the scaling. Allow the heating element to soak for a period of time until the scale accumulation is removed. This might take up to three hours or more. It is dependent on the quantity of buildup that has accumulated in the pipes. After soaking, some accumulation may still be present. It’s best to try to remove it with a towel that has been soaked in vinegar or a descaling solution. Make certain that the hexagon brass tops of the heating components remain completely dry throughout the process. They are equipped with technology that allows the electrical lines to rejoin. After that, make sure that the heating element is free of debris. Afterwards, reinstall it in the chambers from which it was removed. Reconnect the intake hose to the unit’s inlet water line using the hose clamps provided. Place a bucket beneath the outflow pipe so that it is completely submerged. This is where the water that runs out of the unit is collected. Following that, open the intake valve. Drain and check for leaks by allowing water to run through the device. It is possible that mineral flakes (in the bucket) will be expelled from the unit. Alternatively, let the water to continue to run until all flakes stuck inside the unit’s pipes have been flushed out.
Thorough Flushing
Units that are supplied with hard water will require extensive flushing. The same is true for tankless heaters whose owners do not do routine maintenance on them. In this case, just plain water will not be effective for the unit. It is preferable to use 3-4 gallons of undiluted white vinegar rather than diluted white vinegar. You may also utilize a descaling method to help with the scaling. This form of flushing will necessitate the use of a small submersible pump or any other circulating pump.
These hoses will be used to connect the unit’s intake and outflow to the appropriate connections.
The steps are as follows:
- Close the intake valve once again, and then replace the unit’s cover for the time being. Water will not be able to splash onto the electrical components within the machine as a result of this. It is sufficient to secure it with two screws
- After that, fill the bucket with all of the vinegar or descaling solution that you have. After that, install it immediately beneath the water heater unit, as shown. After that, disconnect the intake hose from the water input line of the device. It should be replaced with one of the laundry hoses. Check to be that it is properly attached to the inlet water line
- Then connect the other end of this hose to the output of the submersible pump to complete the installation. Pour vinegar or a descaling solution into the bucket beneath the pump and submerge it. Connect the other end of the laundry hose to the water output line of the unit. Also submerge the other end of the hose in the bucket
- Start the pump by pressing the button. Allow it to suck the vinegar or solution out of the bucket as it pleases. After that, pump it into and out of the unit’s system as needed. Do this for at least 30 minutes
- You may notice some mineral flakes still coming out of the outlet beyond that time period. Allow it to run for a few more minutes in this situation. Make certain that the movement of fluid within the vehicle washes away all of the flakes and scale deposits
Assembling and Final Checks
- Check to see that the unit is free of flakes and scale deposits before using it. After that, switch off the pump and disconnect the laundry hoses from both the water intake and output pipes of the machine. Make a new connection between the intake hose and the unit’s input water line. Reattach the flow resistor to the unit’s outlet by screwing it back in place. Afterwards, attach the outlet valve hose to the flow resistor located on the unit’s outlet. Check for leaks by re-opening the intake valve once again. Afterwards, turn on the exit valve as well. After that, take off the unit’s cover. Then, by inserting the wires into the heating components, you may complete the process. Place the cover back on top of the device. Also, make certain that the screw is securely fastened. After that, turn on the circuit breakers for the device. Then check to see whether the water is heating up via the taps. Finally, you may enjoy your clean, hot water once more.
Check to see sure the device is free of flakes and scale buildup. Afterwards, switch off the pump and disconnect the laundry hoses from both the water inlet and output lines of the machine. Reattach the intake hose to the unit’s input water line once again; and Reconnect the flow resistor to the unit’s outlet by screwing it back in place. Afterwards, attach the outlet valve hose to the flow resistor located on the unit’s outlet; and Examine for leaks by re-opening the intake valve. Afterwards, open both the inlet and exit valves.
Then, by putting the wires into the heating components, you may complete the connection.
Also, be certain that it is securely fastened.
Then, to see if the water is heating, check the faucets.
Filtration Maintenance
Maintaining your tankless unit’s filtration system is an important operation that keeps your tankless unit clean. Consult with your local municipal water provider if at all possible. Inquire about the water conditions in your neighborhood. You may even request that the water be tested. When you live in an area with hard water, this is extremely essential knowledge to have at your disposal. Whole-house water filtration systems can be used to keep filtration systems in good working order. Select the type of filtering you want.
You may find a variety of options at your local hardware or plumbing store.
It’s possible that you have hard water problems in your house.
As a result, the scale building on your tankless heater will be reduced significantly. More information about filtration may be found in the EcoSmartmanual, which can be found here.
Resetting An EcoSmart Heater
Your EcoSmart may still display an error message from time to time. You’ll notice a “E” with a number next to it on the screen. This reading is shown on the LED of the device. In this instance, the following steps will show you how to reset an EcoSmart tankless water heater:
- An error will still appear on your EcoSmart’s screen every now and then. If you look closely, you’ll notice a “E” with a number underneath it. Using its LED, this reading is shown. Following is the procedure for resetting an EcoSmart tankless water heater in this situation:
Your EcoSmart may still display an error from time to time. There will be a “E” with a number next to it. This information is shown on the LED. Here’s how to reset an EcoSmart tankless water heater in this situation:
- Your EcoSmart may continue to display an error message from time to time. You’ll notice a “E” with a number next to it. This information is shown on its LED. In this scenario, here’s how to reset an EcoSmart tankless water heater:
If this is the case, consult theEcoSmart guidebook for more instructions. The instructions on how to reset EcoSmart include instructions on how to do interim solutions. While you wait for the unit to be fixed, you may make use of these temporary remedies to keep your water warm. Sometimes, troubleshooting tips (even those from the handbook) are ineffective. In this instance, it is preferable to have a professional expert come in and fix it for you. Another issue arises when the device is unable to function due to a power failure.
And it’s possible that this caused the fuse in the power board to explode.
You should only attempt to repair it yourself if you are familiar with wiring and circuits.
You may place an order for the particular replacement fuse on the internet.
EchoSmart Heater Maintenance
Some of the manufacturers of these water heaters claim that their devices require no maintenance. There are some who believe that maintenance is either negligible or unneeded. This, however, is not a recommended practice. In addition to following the instructions on how to reset your tankless water heater, regular maintenance is essential for extending the life and usefulness of your heater. Taking care of your home might save you money on unneeded repairs and other expenditures. It’s possible that you’ll have to spend your money on a new purchase.
- This is especially important if you live in a region with hard water conditions.
- If you do not have a water softener, you will need to descale your pipes every six months.
- If this is the case, your heater should be able to run properly for more than three years without the need for flushing.
- However, this is due to the fact that they consume clean filtered water in their houses.
- It is possible that you may need to replace the heating elements, flow meter, or thermistors.
- This is the section where the temperature control knob is located, if you will.
Once again, the type of water supply that your family is connected to can either reduce or extend this process. Tankless water heaters have a lifespan of 20 to 25 years provided they are maintained properly and are properly installed.
Troubleshooting EcoSmart Tankless Water Heater Error Codes
When an error code is generated by your EcoSmart tankless water heater, it will be shown on the screen. If you look closely, you will find that a ‘E’ has a number next to it. The following are the most common EcoSmart tankless water heater fault codes:
- E1 error code indicates that there is a problem with the inlet thermistor. The E2 error code indicates that there is a problem with the outlet thermistor. E3 error code indicates that there is a problem with both thermistors. The E4 error number indicates a problem caused by high temperatures. E5 error code indicates a problem caused by a high flow rate. S103 error code indicates a problem with low voltage.
Begin By Power Cycling Your Unit
If you encounter any of these issues, you may fix or reset them by following the steps outlined in this step-by-step tutorial:
- Make sure that all of the hot water taps in your home are turned off.
- Turn off your EcoSmart tankless water heater if it is not in use. To turn it off, if the EcoSmart unit is included, you may use the remote control that comes with it. To turn it off if it does not have a remote control, just turn it off by pushing the temperature control knob.
- Turn off the circuit breakers if necessary. Make certain that there is no electrical current flowing through the EcoSmart tankless unit while doing this procedure.
- 5 minutes should be enough time to turn off your EcoSmart tankless water heater device
- After that 5 minutes have passed, turn on your EcoSmart tankless water heater.
After those five minutes, turn on your EcoSmart tankless water heater.
Resolving EcoSmart Water Heater Error Codes
After those 5 minutes, turn on your EcoSmart tankless water heater.
E1 Error Code
This indicates a problem with the thermistor. For example, if your EcoSmart tankless water heater device displays the E1 error number, it indicates that the EcoSmart intake thermistor is not reading the right temperature and that you should contact the manufacturer. As a result, replacing the inlet thermistor may be necessary in order to permanently resolve this problem code. However, if you are unable to afford to purchase a new inlet thermistor to replace the damaged one, do not be concerned.
This is a simple remedy for the error code in question.
When trying to resolve an E1 issue, use this step-by-step procedure:
- Bring the water to a boil. As a result, the LED display is switched on, and an E1 error is shown on it.
- 3 or 5 seconds should be spent pressing down on the spherical knob.
- Release the circular knob from its holding position. When the knob is released, the LED display displays or displays the letters CE1
- 2 or 3 minutes should be enough time to keep the water running or flowing.
If you follow these procedures, you will be assured to get hot water from your EcoSmart tankless water heater while you are waiting for the replacement component to arrive in the mail. It is important to remember that when your EcoSmart tankless water heater is operating or functioning in the CE1 Mode, the heating temperature will default to 125 degrees, just as it would with a regular or completely functioning EcoSmart tankless water heater. It is also important to know that you will not be able to change the temperature of the output when in this CE1 Mode.
E2 Error Code
On the outlet thermistor of an EcoSmart tankless water heater, there is a malfunction. For example, if your EcoSmart tankless water heater device displays the E2 error code, it indicates that the EcoSmart intake thermistor is not reading the right temperature and that you should contact the manufacturer. As a result, replacing the inlet thermistor may be necessary in order to permanently resolve this problem code. In the meanwhile, as you await the arrival of a replacement part, you might troubleshoot the problem temporarily.
To temporarily troubleshoot or reset the EcoSmart tankless water heater or to skip the E2 error code, follow the instructions below:
- Turn on the water faucet. For example, if the LED display is switched on, you will observe that it displays the message E2 error.
- Maintain a firm grip on the spherical knob for around 3 minutes or 5 minutes
- Release the circular knob from its holding position. When the knob is released, the LED display displays or displays the letters CE2
- 2 or 3 minutes should be enough time to keep the water running or flowing.
If you follow these procedures, you will be assured to get hot water from your EcoSmart tankless water heater while you are waiting for the replacement component to arrive in the mail. It is important to remember that when your EcoSmart tankless water heater is operating or functioning in the CE2 Mode, the heating temperature will default to 125 degrees, just as it would with a regular or completely functioning EcoSmart tankless water heater.
It is also important to know that you will not be able to alter the temperature of the outlet when in this CE2 Mode. When attempting to get a certain desirable temperature, it may be necessary to combine hot water with cold water to achieve the desired result.
E3 Error Code
On the input and outlet thermistor of an EcoSmart tankless water heater, there is a mistake. For example, if your EcoSmart tankless water heater device shows the E3 error number, this indicates that the EcoSmart intake thermistor is not reading the correct temperature. As a result, replacing the inlet thermistor may be necessary in order to permanently resolve this problem code. In the meanwhile, as you await the arrival of a replacement part, you might troubleshoot the problem temporarily. Please keep in mind that this is simply a temporary solution to the problem.
- Turn on the water faucet. For example, if the LED display is switched on, you will observe that it displays the message E3 error.
- Maintain a firm grip on the spherical knob for around 3 minutes or 5 minutes
- Release the circular knob from its holding position. When the knob is released, the LED display displays or displays the letters CE3
- 2 or 3 minutes should be enough time to keep the water running or flowing.
If you follow these procedures, you will be assured to get hot water from your EcoSmart tankless water heater while you are waiting for the replacement component to arrive in the mail. It is important to remember that when your EcoSmart tankless water heater is operating or functioning in the CE3 Mode, the heating temperature will default to 125 degrees, just as it would with a regular or completely functioning EcoSmart tankless water heater. It is also important to remember that you will not be able to alter the outlet temperature when in this CE3 Mode, which is a limitation.
E4 Error Code
It is not always necessary to do a reset in order to resolve an E4 Error Code problem. It is due to a clerical error on the High Temperature setting. Assume that the E4 Error Code is being read or shown by the LED control board of your EcoSmart tankless water heater. In that situation, it indicates that the incoming water temperature is around 150 degrees Fahrenheit or higher, according to the EcoSmart device. The EcoSmart tankless water heater has 2-4 thermostats, which is sufficient for most households.
All of the thermostats have a temperature rating of 140 degrees.
If your EcoSmart tankless water heater shows an E4 error code, you will need to drop or reduce the incoming water temperature to a reading of less than 140 degrees Fahrenheit to avoid damage to the unit.
E5 Error Code
E5 is an error that occurs as a result of the high flow rate. If the E5 error code is shown on the LED control board of your EcoSmart tankless water heater, it implies that the requested water volume is more than the available water volume.
As a result, you will be obliged to lower the flow rate down significantly. An aerator may be found in every sink, shower, and bathtub. The aerator aids in the regulation of water volume.
- There is a difference between 1 gallon per minute and 2.5 gallons per minute in the sink.
- The shower has a water flow rate of 1.5 gallons per minute to 3 gallons per minute, depending on the setting.
- With a water flow rate ranging from 3 to 8 gallons per minute, the bathtub can accommodate most people.
If you want to know how much water is flowing through your EcoSmart tankless water heater system at any one time, follow this step-by-step guide:
- Find the On button on the EcoSmart display panel and press it.
- For approximately 10 minutes, press and hold the On button. This will assist you in obtaining the diagnostic screen.
- Navigate through the three screens of the diagnostic menu after it has been activated. This may be accomplished by twisting the spherical knob in a counter-clockwise manner on the console. The three displays are as follows:
- The first appearance. It displays the temperature of the incoming water
- This is the first turn. It shows the temperature of the water coming out of the outflow
- This is the second turn. It displays the current flow rate in real time. One aspect of this screen is that it features a decimal point that is concealed from view.
That brings us to the second round. It displays the current flow rate at the time of writing. There is a concealed decimal point on this screen, which is a unique feature.
S103 Error Code
S103 is an error that occurs when the voltage is low. If the S103 error code appears on the LED control board of your EcoSmart tankless water heater, it indicates that the EcoSmart tankless unit is not receiving the appropriate amount of electricity to operate properly. The EcoSmart tankless water heater requires a voltage of 208 volts or greater in order to function properly. This means that a test of the power supply to your EcoSmart tankless water heater will be necessary by the manufacturer.
As a result, the water will begin to warm up.
Sources
- ECOSMART WATER HEATER ERROR CODES
- Interactive Troubleshooting Guide
- ECOSMART WATER HEATER ERROR CODES
DISCLAIMER: The information provided on HomeInspectionInsider.com is not intended to be professional guidance. Before beginning any job, you should contact with a competent expert and verify that all necessary permits have been obtained. It is owned and operated by Hubert Miles who is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by placing advertisements and links on their websites that direct traffic to Amazon.com (hereinafter referred to as “Amazon.com” or “Amazon.com Associates Program”).
Hubert Miles receives a commission for recommending visitors and commerce to these businesses.
How To Repair An Eco Smart Tankless Water
The reset button is positioned on the water heater, and it is represented by a red button. Some water heaters have two thermostat buttons, one for each temperature setting. It may be necessary to remove the metal plate that keeps the thermostat in place in order to access the reset button.
Why is my ecosmart water heater not working?
If you are receiving hot water despite the fact that the digital display is not illuminated, the fault is with the electronic circuit board (ECB). Having trouble receiving hot water might indicate a problem with either the plumbing or electrical connections in your home. To troubleshoot the equipment, call our customer care line at 877-474-6473 and provide your installer’s name and phone number.
What do you do when your tankless water heater stops working?
If your water is getting too hot, these are the things you should do to cure it: Stop overtaxing the system by pressing too many buttons at the same time. Set the temperature of your water heater to around 120 degrees Fahrenheit. Adjust the location of your temperature sensor in order to obtain a more precise measurement. Inspect and clean the inlet filter on your tankless water heater. Remove any stumbling blocks once more.
Why would a tankless water heater stop working?
If your water is getting too hot, here are some things you can do to correct it: Reduce the number of times you tap the screen at the same time to avoid overwhelming the device.
Adjust the temperature of your water heater to around 120 degrees Fahrenheit. You may improve the accuracy of your temperature sensor by repositioning it. It is necessary to clean the intake filter on your tankless water heater. Remove any obstructions once more.
How do I reset my ECO water heater?
Pressing the red Reset button on the ECO, which is normally linked to the top thermostat, will restore it back to its original settings. When a water heater’s electronic control unit (ECO) starts tripping on a regular basis, it’s time to call a plumber.
How old is my EcoSmart water heater?
You may contact EcoSmart’s customer service department at 877-474-6473 with the serial number of your water heater, or you can send them an email at and they will supply you with the date of manufacture.
What does E4 mean on EcoSmart tankless water heater?
If your tankless water heater’s E4 error code is shown on the display, it indicates that there is an issue with the flow meter sensor (also referred to as cold water temperature sensor.) As a result, the flow meter is not transmitting a signal to the computer, which is responsible for starting the machine.
How long should a tankless water heater last?
It is estimated that most tankless water heaters will last more than 20 years in normal use. They also feature readily changeable parts, which might potentially increase their lifespan by many years. Storage water heaters, on the other hand, have a lifespan of 10–15 years.
What is the most common problem with water heaters?
Water leaks are one of the most prevalent types of water heater problems that you’ll come into. Any water heater will ultimately begin to leak due to the fact that water will corrode the tank and cause microscopic cracks or fractures over time.
What to check if water heater is not working?
A water heater that does not generate hot water might be due to a lack of electricity, a tripped limit switch, or one or more faulty heating components, to name a few possibilities. As a first step, make sure that the circuit breaker for your water heater is not tripped on your panel of electrical circuit breakers. Switch off the circuit breaker and then turn it back on if it has been tripped.
How much does it cost to fix a tankless water heater?
Troubleshooting Common Tankless Water Heater Problems Professional repairs are frequently necessary, and they can cost anything from $150 to more than $800, while the average cost is usually around $600. Tankless water heaters must be flushed on a regular basis to prevent mineral and sediment buildup inside the device.
Do tankless water heaters have a pilot light?
When you use a gas tankless water heater, the heat is generated by a pilot assembly and burners, which is then transmitted to the water as it travels through the device on its way to your faucet. By evaluating your circuit breaker and looking for a visible pilot light, you can determine if you have an electrical or gas problem.
Why do I have to keep resetting my tankless water heater?
When your thermostat ceases to function properly, it may be unable to manage the temperature of your electric water heater as well as before. Your water will then heat up to unsafe levels, causing the reset switch to trip as a result of the increased heat.
What does the reset button do on a hot water heater?
When your thermostat ceases to function effectively, it may be unable to maintain adequate temperature regulation in your electric water heater. Your water will then heat up to unsafe levels, causing the reset switch to trip as a result of the increased temperature.
Why can’t I reset my water heater?
So, what should you do if the water heater’s reset button does not function properly?
It’s possible that your thermostat is malfunctioning. If the hot water heater continues tripping the reset button, the high limit switch may be the source of the problem. What’s going on is that the thermostat isn’t correctly controlling the temperature.
Why is my tankless water heater beeping?
When a water heater detects a leak, it may emit a beep to alert the homeowner. The presence of a leak may be visible if the floor is moist near the water heater, but the leak might be further down the line. Depending on the equipment, the beeping might be caused by a water heater shutdown feature or by a flood prevention system. A gas leak may also be indicated by beeping.
How often should a hot water heater be replaced?
If your tank water heater has been in service for more than ten years, it may be time to consider replacing it altogether. A tank water heater tank should last between six and twelve years if it is properly maintained. It is possible for a tankless water heater to operate for more than 20 years. Check the warranty on your water heater for the most up-to-date information on its service schedule.
How old is my Ruud water heater?
The year of manufacturing of a Ruud water heater is indicated by the third and fourth numbers in the serial number, which are normally found after numerous letters.
How long do electric water heaters last?
The year of manufacturing of a Ruud water heater is indicated by the third and fourth numbers in the serial number, which are normally found after a series of letters.
How do I fix E4 error on my air conditioner?
In the event that your portable air conditioner displays an E4 error code, what should you do? Replace your air filters on a regular basis. Have your refrigerant levels checked by a professional, such as an EPA-licensed air conditioning expert. Every year, clean the evaporator and condenser coils. Make certain that you have a sufficient power source.
Can I use CLR to flush my tankless water heater?
When cleaning a tankless water heater, CLR can be used with distilled vinegar for maximum effectiveness. Adding one capful of CLR to each gallon of white vinegar can aid in the removal of stubborn deposits from within your water heater’s heating element.
Ecosmart Tankless Water Heater
Tankless Water Heater from Ecosmart Joe Hitchcock is an American film director and producer who is most known for his work on the film The Birds. 2021-09-27T15:17:13-04:00
Ecosmart Tankless Water Heater:ReviewBuying Tips
- Reviews: 4.5 out of 5 stars from more than 3700 global Amazon reviews
- POE | 240V | 2x40A breakers are the most common.
EcoSmart tankless water heaters are among the best-selling electric water heaters in the world, according to the International Energy Agency. Compact and energy-efficient, the ECO line is designed to conserve both energy and water through the use of self-modulating electrical power, making it ideal for small and compact spaces. Environmentally friendly heater maker EcoSmart has a significant internet presence and sells mostly through online merchants such as Amazon. Here’s where you can find our selection of the Best Electric Tankless Water Heaters.
When installed appropriately, this heater is capable of supplying endless hot water to every shower, sink, and appliance in your home at any time.
Products’ specs and crucial aspects like as water flow, heat output, prior customer evaluations, and the opinions of professional reviewers have all been taken into consideration.
The Ecosmart ECO 18 is available through Amazon in the United States, with Prime delivery included. Check out the product description page for additional information on the product.
Ecosmart ECO 18:Overview
The Ecosmart ECO Electric Tankless Water Heater is a medium-sized tankless water heater with a typical structure. It operates on electricity and heats water. It makes use of copper coils and a flow sensor to recognize when hot water is required and to deliver the appropriate volume of hot water. In warm areas when the incoming water temperature is 60 degrees or above (as is the case in most mild climates), the ECO 18 may produce between 2.5 and 4.4 gallons of water per minute with an output temperature range of 80 to 140 degrees.
Most families with up to two bathrooms and typical water consumption patterns will benefit from the Ecosmart ECO 18, which is our Best Buy recommendation.
Heater features:
- Simple, annual maintenance is required. There is no need for a water tank, lag time, or water waste. Copper heating coils and stainless steel construction are used. The ECO 18 can reach temperatures of up to 140 degrees Fahrenheit. In moderate conditions, the flow rate may reach 4.4 GPM. Self-modulating (it automatically controls the temperature and flow of water)
- Activation of the 0.25 GPM sensor
- Warranty for a limited duration only
- Display using digital LED technology
- It can save up to 12 cubic feet of storage space.
Energy efficiency ratings/certifications:
Ecosmart, as its name implies, manufactures some of the most energy-efficient water heaters available on the market. At 99.8% efficiency, the ECO 18 is virtually waste-free, devoting all of its electrical draw to the process of heating your water to your satisfaction. In accordance with UL-499 and the Canadian Standard CAN/CSA-C22.2 No. 64, the ECO 18 was ETL listed. This includes a lead-free guarantee provided by the Water Quality Alliance, as well as other benefits.
Flow rate/water pressure:
For the majority of users, the ECO should supply a least of 2.5 gallons per minute (this permits one shower head and one sink with a low intake water temperature to function at the same time). In optimum conditions, this heater will deliver up to 4.4 GPM of output. The amount of GPM you can really obtain is determined on the flow rate and temperature of the entering water. Ecosmart provides consumers with a useful map that helps them determine their typical input water temperature:
Heating capacity:
For the majority of users, the ECO should supply a least of 2.5 gallons per minute (this permits one shower head and one sink with a low intake water temperature to run at the same time.). This heater can produce up to 4.4 GPM under optimal conditions. Depending on your incoming water flow and temperature, you can obtain different GPM rates. In order to find out what your typical inlet water temperature is, Ecosmart provides clients with a handy map:
Fuel type:
This is an 18-kilowatt heater that requires 240-volts to operate. You’ll need a 150-amp panel (with a maximum draw of 75 amps) and enough space in your service panel to accommodate two 40-amp double pole circuit breakers in order to run it securely. It is less expensive to install the ECO 18 than gas tankless water heaters since it does not require any ventilation, unlike gas tankless water heaters.
Heater applications:
In addition to residences of any size, Ecosmart recommends its ECO heaters for commercial settings such as offices or restaurants, recreational vehicles, and as a point-of-use installation for on-demand heating in any building with suitable electrical wiring.
Display type:
- A digital thermostat that is simple to operate
- The design interface, according to the reviewers, is intuitive and user-friendly.
Material Composition:
Throughout the model’s interior and exterior construction, corrosion-free copper and stainless steel components are used in large quantities to prevent corrosion. Durable.★★★★★
Customer reviews for Ecosmart ECO 18:Highlights
- A great number of good evaluations point out the precision with which Ecosmart’s Temperature Control delivers rapid water at the chosen temperature. It has been noticed by reviewers that it can offer numerous showers operating at the same time (when the appropriate size Ecosmart heater is fitted)
- More than a few reviews describe having great experiences while contacting Ecosmart’s technical support service. According to several reviews, the Ecosmart heater offered good value for money when compared to similar but more costly heaters.
Reading customer reviews:Any downsides?
- The Ecosmart lifetime warranty is conditional, which means that it must be met in order for it to stay effective. Some reviewers allege that their warranty was not fulfilled because they did not adhere to the terms and conditions of the manufacturer. Among these include regular maintenance, softening very hard incoming water using a water softener, and scheduling a professional installation
- And Some reviewers who have been using the Ecosmart heater for a long period of time have noticed an increase in the time it takes to activate the hot water—up to around 30 seconds. A rusted heating element is typically the cause of this problem with electric heaters.) In one review, a user stated that the ECO 18 is “okay when you set it on the dishwasher while you hop in the tub, but it is not designed to accommodate three students utilizing three bathrooms at the same time.”
On the Amazon product page for the Ecosmart ECO 18, you can read all of the customer reviews.
Brand reputation: Are Ecosmart tankless water heaters any good?
The Ecosmart ECO 18 product page on Amazon contains a comprehensive list of customer reviews.
Installation:Product manuals and guides
Ecosmart is a United States-based corporation that was created in Connecticut and operates out of both Connecticut and Florida. Online suppliers, on the other hand, claim that their heaters are manufactured in China before being transported and/or built in the United States.
What does E5 mean on Ecosmart tankless water heater?
People who are seeing the E5 fault number on the digital screen of their Ecosmart heaters frequently ask questions about them. It is possible that the E5 error code is caused by a problem with the pressure switch, in which case the volume of water is too large and the flow rate must be reduced in order for the heater to work correctly. Ecosmart proposes the use of a flow restrictor or manually altering the essential water valves in order to reduce the volume of water going through the system, according to the company.
The following are examples of common erroneous readings on the Ecosmart ECO 18:
- E1 indicates an error with the inlet thermostat
- E2 indicates an error with the outlet thermostat
- E3 indicates an error with thermistors
- E4 indicates a high temperature error
- E5 indicates a high flow rate error. S103 is an error with low voltage.
How to reset an Ecosmart tankless water heater
Make sure all water outlets in your house are turned off before turning off the Ecosmart heater. simply turning the temperature control knob to the desired setting Open the service panel and turn the circuit breakers that supply power to the heater on and off. Wait 5 minutes before turning on the warmth once more. Here is the Ecosmart troubleshooting guide for ECO heaters ranging in power from 18 to 36 kW.
How to install an Ecosmart tankless water heater
Installing the Ecosmart unit itself is rather straightforward, and it can be completed without the assistance of a professional as is the case with other tankless heaters. Connecting the heater to your home’s power, on the other hand, might be a difficult operation if your present wiring does not fit the heater’s specifications. If you’re not completely sure in your ability to handle electrical and plumbing work in your house, call a professional. Here are the Ecosmart’s basicInstallation Manual (PDF) and User Manual, which you can download for free.
Other Ecosmart ECOtankless electric water heaters
There are numerous sizes of EcoSmart tankless water heaters available, ranging from the smallest 3 kW POU Model up to a large 36 kW heater that can serve the entire house. Here’s some product paperwork from Ecosmart that details the specifications of the various heaters in the ECO line. The ECO 11 and the ECO 18 are the two most popular versions in the series, owing to their adaptability at both point-of-use and whole-home applications, as well as their affordability. No matter whatever heater you choose, though, you should notice a significant increase in the usefulness of your home.
What size Ecosmart electric tankless water heater do I need?
Choose the smallest Ecosmart unit that is capable of delivering sufficient GPM for your requirements. When making your selection, remember to take into consideration the usual winter temperature of your incoming water, as well as a little wiggle room between your maximum water requirements and your maximum heater capacity.
ECO units with a capacity of up to 11 kW are considered point-of-use heaters, whilst those with a capacity greater than 11 kW are often utilized in whole-house applications:
Bottom line– Should I buy this specific tankless water heater?
Our Best Buy selection, the Ecosmart ECO 18, is distinguished by its reasonable pricing, outstanding energy efficiency, and good customer ratings. Because of its innovative self-modulating technology, running out of hot water is extremely unusual, even during periods of heavy demand. Copper and stainless steel components in the ECO assist to boost durability and extend its average lifespan to 20 years or more, greatly beyond the lifespan of typical tank heaters. Consider the ECO 18 to be the greatest tankless electric water heater available for less than $500.00.
Licensed under Creative Commons Attribution 4.0 International License
EcoSmart ECO-18 Electric Tankless Water Heater 18KW 2+ Bath
- Is there a warranty on this particular unit? A limited lifetime guarantee on electrical components, as well as on heat exchangers, is included with every EcoSmart water heater purchase. In what sizes do the fittings on this item come? Inlet and outlet connections are made via 3/4-inch fittings on the EcoSmart Eco-18 tankless water heater, which are both placed on the bottom of the device. In order to use this item, what electrical criteria are required? The EcoSmart Eco-18 tankless water heater operates on 240 volts and is a two-line heater, according to the manufacturer. It draws 150 amps, necessitating the use of two Double Pole 40 amp breakers as well as 8/2 wire (8 gauge). What is the maximum number of bathrooms that this unit can supply hot water for? The EcoSmart Eco-18 tankless water heater is a large-capacity device with 18KW of heating power. In warm areas, this unit is perfect for 2.5 bathrooms, while in colder climates, this unit is suitable for up to 1.5 bathrooms. Is a pressure relief valve necessary if the flow rate is around 10 GPM at 60 psi? Yes, it comes highly recommended. What is causing the power outage? We can assist you in diagnosing the problem with the Ecosmart 18kw. Please contact us via phone at (305) 823-6991.