How To Replace Whole House Water Filter

7 Steps to Change Whole House Water Filter

The entire home water filter, like all other appliances, has to be checked from time to time for efficiency. Changing your cartridge on a regular basis is an excellent approach to ensure that it remains in good working order at all times. Nevertheless, the most important question is: how do you update your water filters? In addition, how frequently do they need to be replaced? When you fail to replace them, what will be the ramifications? In this post, we’ll go through how to change the entire home water filter and give you some helpful tips.

What Are Whole House Water Filters?

Whole-house water filters are specialized water filtration systems that filter water from all of the outlets in a home’s plumbing system and appliances. As a result of their installation in the main water supply, these devices ensure that every other faucet in the building may dispense safe drinking water. The faucet water filter is a less expensive alternative to a whole-house water filtration system. This, on the other hand, is mounted on each faucet and filters only the water that comes from those specific outlets.

The AGravity filter is ideal for use on your counter top.

How to Change Whole House Water Filter

Whole-house water filters are specialized water filtration systems that filter water from all of the outlets in a house or other building. They are put in the main water supply, allowing clean water to be dispensed from every other faucet in a building as a result. As an alternative to a whole-house water filter, a faucet-mounted water filter can be installed. But this is fitted on each faucet and filters only the water that comes out of those specific outlets. It may be placed beneath the sink or on the countertop of a specific space.

All faucets, however, generate safe drinking and cooking water when a whole-house water filter is used.

Step 1: Turn Off Water Supply and Release Pressure

First, make certain that the water supply has been entirely shut off at the valve or main water feed. Pushing the red knob will relieve the pressure. Make careful to pay attention when you press the pressure release knob, since water will spew out.

Step 2: Take out Casing and Tidy up O-Ring

Remove the case by unscrewing it and removing the large O-ring. The O-ring has a big diameter and is attached to the casing by a little black plastic band, which you will discover within the casing when you open it. Remove the ring from its original location and clean it well. If it has deteriorated to the point of becoming dangerous, replace it.

Step 3: Throw Old Filter Away and Tidy Up Housing

Remove the old water filter and dispose of it in an appropriate manner. After you have completed this, the following step will be to clean the casing by removing any debris that has accumulated inside of it. After that, wash the casing with warm water, household soap, and a soft cloth or sponge to remove any remaining dirt.

After that, fill the housing with about a third of the water it holds and add a little bit of bleach to it before washing it. Washing the case gently and carefully is recommended to avoid causing any harm to the product. Once you’re through, rinse it twice more and set it aside to dry.

Step 4: Apply Lubricant to O-Ring

Clean silicone grease should be used to lubricate the O-ring in order to ensure that it sits correctly in the casing of the device. Because silicone oil does not cause the rubber to soften or swell, it is extremely necessary to apply silicone grease. Return the O-ring to its groove on the ring. When installing the O-ring, take care not to overtighten it, as this might cause the housing seal to break.

Step 5: Buy and Install a Brand New Water Filter Cartridge

Replace the water filter with a new one. Whether you opt to purchase a reverse osmosis system or any other type of water filter, make sure to inspect the housing to ensure that there is a standpipe in the centre of the housing. It is in the shape of a round gadget with a short rubber pipe extending from the top. It is critical that the filter be appropriately positioned over the water filter cartridge during installation. The reason for this is that this device functions as a water port, and as a result, all of the water that you use in your home is filtered here before it is distributed via your home’s plumbing.

Step 6: Screw Casing to Cap

By physically inserting the filter cartridge into the case, you may swap out the filter cartridge. Ascertain that the filter is positioned in the center of the standpipe. Although you may not be able to see it, the standpipe is beginning to slip into the cartridge aperture with relative ease. It is important not to overtighten the casing, since this might cause it to break.

Step 7: Turn Water Supply Back On and Test Pressure

The water supply can be restored by gently turning the intake valve to the “on” position. However, proceed with caution since the water may squirt out with force, destroying the housing and even destroying the entire device. Turning the inlet handle very gently and stopping the inlet valve if the water rushes too rapidly are the proper ways to go about it correctly. When replacing a whole-house filter, exercise caution at all times. Pushing the red knob will allow you to check the pressure. Water will be sprayed out, so be prepared to get a bit wet.

Important Tips Regarding New Filter Replacement

After you have changed the filter and sealed the housing, turn on the water and let it running for 6–7 minutes without using it. Allow it to run for a few minutes to aid in the removal of dirt. The reason for this is because when you replace the filter, it is likely that water sediments will have entered the tap.

How Often Should I Change A Whole House Water Filter?

A typical filter has a lifetime of between 1 and 6 months, depending on the model. Sediment pre-filters have a lower useful life than sediment filters. The post-filters can survive for nine months or more, and the carbon filters are the most durable (lasting 14 to 15 months on average). There are a variety of indicators that your filter is malfunctioning. One of these is an unpleasant odor or taste that you begin to notice in your water as time goes on. Additionally, the flow rate and pressure of the water will alter.

If it is worn out or old, it should be replaced as soon as possible the following time.

However, if it is still clean and in good condition, you can continue to use it for a short period of time. However, the factors listed below will also influence how frequently you will need to replace your whole home water filter.

  • Their dimensions, capacities, and types (measured in months or gallons)
  • And The quality of the supply water (a greater concentration of pollutants will shorten the filter’s lifespan and increase the likelihood of a replacement)
  • Sediment, iron content, and other contaminants are all considered. Hardness of the water
  • Using well water vs municipal water

Why You Need To Change Filter

You may make changes to your whole home system whenever you want, which is a huge advantage of having one installed in the first place. Additionally, the technology allows you to modify the water pressure across your entire home in a single step. The purchasing of high-quality water filter cartridges is recommended due to the fact that they last longer and perform more efficiently. Cartridges of good quality can last for up to 36 months, whilst others may only survive for 3 months or less. Changing your water filter on a regular basis is a good idea since it helps to improve the effectiveness of the filter.

If you are unsure how to change a full water filter, see the unit’s owner’s handbook for instructions.

Check to determine whether the cartridge is compatible with the sort of pollutants in your drinking water.

Wrap Up

Water filters for the entire home are quite simple to replace and have the added benefit of reducing water-borne illness rates in a household. When we drink and wash in clean water, we feel better about ourselves. When replacing your water filter, make sure to put on your safety eyewear. Also, keep in mind that if you notice anything strange about your water source, you should conduct a water screening test. Is there anything you’d want to add to this article on how to change entire house water filters?

How to Replace a Whole House Water Filter Cartridge

Water filters for the entire household are quite simple to replace and have the added benefit of reducing water-borne illness rates in a residence. When we consume and bathe in clean water, our lives improve. When replacing your water filter, always sure you use protective eyewear. Keep in mind that if you notice anything strange about your water source, you should do a screening test on it. Is there anything you’d want to ask or say about how to change your whole home water filters? Let us know what you think in the comments section or by sending an email.

Important Tips

WATER SHOULD ALWAYS BE TESTED. Use with water that is microbiologically dangerous or of unknown quality only if suitable disinfection has been performed before and after the unit before use. FILTER CARTRIDGE FLOW RATES are calculated based on the performance of a “clean” cartridge. A filter cartridge / housing with a Gallons Per Minute rating that is two times the needed flow rate should be selected for the job. This enables the cartridge to perform its function for a longer amount of time before the flow rate or pressure deteriorates to an unacceptably high level.

A FILTER CARTRIDGE should be replaced at least once every six months to prevent germs from building up over time. Consider making it a regular part of your routine to replace your filter cartridge at the same time you change your clock.

Instructions

Point of Entry (POE) is a location AFTER the water meter (municipal water) or the pressure tank (private water / water well) and Point of Use (POU) is a location PRIOR to the faucet or appliance in this installation.

  1. Shut down both the intake and outlet valves to relieve pressure in the system. Fill a bucket with water and place it directly beneath the filter housing. Remove the bowl by carefully unscrewing it in a counter-clockwise direction (to the left) using a filter wrench. Remove the used cartridge and throw it away. Pour the contents of the filter bowl into a bucket. Remove the O-rings and clean them well of any lubrication. Check for damage and place the item aside. If the O-ring is damaged, it should be discarded and replaced. Fill the bowl three-quarters of the way with water and add 1 tablespoon (30 mL) bleach. To eliminate any accumulation of bacterial, rust, and scale particles, scrub well with a non-abrasive sponge or cloth before rinsing completely with water. Check to see that the O-ring grooved sitting region is free of debris. Remove the cartridge from its protective box and set it in a bowl, making sure it fits over the post. Apply petroleum jelly to a fresh or cleaned O-ring before inserting it into the O-ring groove. (Optional) Examine to see that the O-ring is seated level and evenly in the groove. Set up the bowl in a clockwise direction (towards the right), twisting carefully until the cartridge is aligned with the post in the filter head – or until it is hand tight. DO NOT TIGHTEN TOO MUCH
  2. In order to prevent flooding, depress and hold the red pressure relief button while gradually opening the INLETvalve as water fills the housing until it runs out of the relief button. Open the OUTLETvalve carefully to remove any trapped air from the line. Before using the system, flush it for several minutes. Look for any leaks.

Just keep in mind that the life of a filter cartridge varies depending on the amount of time it is used and the quality of the water. It is possible that the filter cartridge needs to be replaced if there are changes in the flavor, color, or flow of the water being filtered. More information may be found in our ‘Choosing the Appropriate Water Filtration Solution’ article. If you are not confident in your ability to replace this, you should get a licensed plumber to do it for you instead. If this device is not placed correctly, it may result in water problems down the road.

How to Change a Whole House Water Filter – Replacement Tutorial

This page may contain affiliate links, so please keep that in mind. If you purchase a product or service after clicking on one of these links, we will get a commission at no additional cost to you. See our product review method in further detail, or read our FTC affiliate disclosure for more information. Almost all whole house water filters require a small amount of maintenance every now and then in order to function at their peak performance levels. In most cases, replacing the cartridges on time solves the problem.

And what happens if you don’t take care of your responsibilities?

Contents

  • Tools and supplies required
  • Step-by-step instructions
  • And more In the video, what happens if I’m on a well?
  • My filter housing has been stuck
  • Please assist me. How frequently should a whole-house water filter be changed
  • How does it affect your health if you don’t update your filter?

Whole House Water Filter Replacement

As long as you have all of the essential equipment and accessories on hand, and you know what you’re doing, replacing a whole home water filter will take only a few minutes. You don’t have any? If that’s the case, the following information may be of assistance:

ToolsAccessories Needed

  • Replacement cartridge
  • Housing wrench
  • Bucket
  • Bucket filled with soapy water (optional)
  • Household bleach (optional)
  • Replacement cartridge

Step-by-Step Instructions

  1. Whenever possible, the first step is to switch off the water supply. Close the valve at the main water line, or the inlet valve directly before your filter if you have an additional filter installed, to do this. Another possibility is that the machine has a built-in valve that you may use to shut it down. Open as many faucets or other outlets as you can to drain as much of the leftover water as you possibly can. Whenever you notice a considerable decrease in flow rate and pressure, the majority of the water in your plumbing system has exited
  2. If your plumbing system has an output valve, now is the time to close it. As a result, water will not be able to drain back into your home. For a couple of seconds, push and hold the pressure relief button on each filter housing to ensure that you are not dealing with an overpressure situation. With the help of the wrench, remove the (first) housing from its mounting. Keep an empty pail on hand to catch any spilled water if necessary. Remove the old cartridge from within the housing by pulling it out with your fingers. Put it in the empty bucket for the time being, and remember to properly dispose of it after you’re finished with it. Optional: The housings are an example of a component where dirt and germs are prone to build up over time. Consequently, it’s always a good idea to clean the interior of your refrigerator with soapy water or household bleach and a toothbrush. Once you’ve finished, thoroughly cleanse your hands with plain water. Using food-grade silicone oil, lubricate the O-ring on the housing and check to see that it is seated level in its position. If the O-ring is no longer in excellent condition, it should be replaced. Insert a fresh cartridge into the housing and tighten the screw to secure it. It should be sufficient to tighten by hand – an O-ring that has been correctly installed will prevent any leakages. You may now gradually restore water pressure to the system. Open all of the valves in the system that are upstream of it. Look for any leaks. Special care should be paid to any and all of the housings that you have just removed. Should a leak occur, cut off the water supply immediately and gently tighten any connections to halt the dripping
  3. If the leak persists, call a plumber. You may now turn on the water supply permanently, as well as all of the valves heading away from the unit. Open numerous faucets to allow the new cartridge to be flushed for a couple of minutes after installation (see manufacturer instructions). This will also aid in the removal of any trapped air from your plumbing system. Once the water pressure and flow rate have returned to normal, you may turn off all of the faucets and call it a day.
See also:  How To Install On Demand Water Heater

Video

Didn’t bother to read because you were too lazy? Take a look at this video:

What If I’m on a Well?

This isn’t really significant. The process of changing a well water filter is identical to that of replacing one on a municipal water source.

Help, My Filter Housing Is Stuck!

If your filter housing is stuck and you’ve already opened one or more faucets to relieve some of the pressure inside of it, as well as utilizing the pressure release button on the top, don’t give up hope just yet! There is still hope! There are a handful of things that may be of assistance:

  • It is sometimes sufficient to tap on the filter head outside the thread
  • To use a hair drier and blast hot air on the top
  • To use a wrench and push the filter head as far up the housing as it will go
  • Etc. With your free hand, hold the filter bracket in position. Make an effort to spin the wrench in a clockwise fashion (looking down on the filter). If it doesn’t work, consider using some more leverage, such as a tube. If you have a plastic wrench and it begins to flex, you may need to replace it with a metal wrench. Another interesting approach is to use two plastic wrenches at the same time.

Didn’t seem to be working? Once the unit has been gently removed from the water line, it is recommended that it be placed in a vice. You can now push the housing open with your physical might. In the event that you are tired with your current filter, read our whole home water filter reviews to choose a replacement. What can you do to ensure that this doesn’t happen again? First and foremost, check to see that the O-ring is in good condition and free of dirt.

If you detect any cracks or other problems in the O-ring, you should replace it. When you’re finished, lube it with food-grade silicone grease (as described above). Additionally, make certain that the seat and contact surface within the head are free of debris.

How Often to Change a Whole House Water Filter

The frequency with which you should update the filter(s) in your whole home system is determined by a number of factors:

  • Their size and capacity (measured in gallons and/or months)
  • Their kind
  • And their capacity Feed water quality (more contaminants will shorten the filter’s lifespan and, as a result, increase the frequency of replacement)
  • Well water vs. city water
  • Sediment and iron levels
  • Water hardness
  • Other contaminants

Generally speaking, most filters will last somewhere between 1 and 6 months in most cases. Pre-filters made of sediment must be changed on a regular basis, but carbon filters have a longer life expectancy than sediment. Post-filters have a shelf life of nine to twelve months. Discoloration and an unpleasant taste or odor, as well as a decrease in water pressure and flow rate, are all indications that your filter has surpassed its capacity and is blocked, and should be addressed as soon as possible.

At the time of replacement, what condition does it appear to be in?

If it’s very unclean and worn out, change it sooner the next time.

Customer service will be able to provide you with a more exact time range.

What Happens If You Don’t Replace Your Filter?

What happens if you don’t replace your filter on time as you had intended? It will lose its ability to filter out harmful substances. For example, an outdated sediment filter that is designed to collect particles such as rust may enable some of the pollutants to flow through, resulting in contaminants ending up in your drinking glass and compromising the function of your other household appliances, among other things. The worst-case situation is that the lifespan of your water heater, washing machine, dishwasher, and other appliances will be significantly reduced.

  • This is something that you must avoid at all costs if you want to keep your health.
  • Thank you!
  • She is the head of content production and has completely immersed herself in the home water treatment sector, resulting in her becoming an expert in the field herself.
  • Find out more about.

How to Install a Whole House Water Filter

The clarity, cleanliness, and flavor of your water are important factors to consider whether it comes from a well or a municipal water delivery system. However, this is not always the case. So, other than stocking up on bottled water or shelling out a lot for a state-of-the-art water filtration system, what options do you have? An entire home water filter may be installed, which will offer clean, clear water for all of your household’s requirements. We’re going to put up a whole-house water filter today, so stay tuned.

  1. Following that, we’ll go through the many types of filters that may be utilized with our system, as well as the various levels of filtration provided by each.
  2. Take the unit out of its packing and inspect it to ensure that we have all of the necessary parts.
  3. Let’s get started with some preliminary assembly.
  4. Next, using an adjustable wrench, we’ll tighten down the fittings into the head cap, taking care not to over-tighten the assembly.
  5. Alternatively, we might have utilized this 3″ mail threaded copper compression fitting, but we would have had to solder the ends of the fitting to the existing water lines.
  6. The water supply must be turned off and a faucet must be opened to release pressure in the line prior to installing the unit.
  7. This will need some investigation on your part, as well as an awareness of how water comes into the house from the well or municipal supply line located outside the house.

We don’t require filtered water for outdoor consumption.

In order to have enough of space to remove the cartridge for filter replacements, we’re placing our filter on a water line near the ceiling.

Simply ensure that there is 1-1/2″ space below the housing so that you can remove it to replace the filters.

However, because we do not have any slack in the lines, we must use a slip joint push fitting, such as this one, which we have used in other projects for the same reason as this one.

Using this copper tube cutter, we’ll start by cutting a small hole in the existing water line to serve as a starting point.

It may take several minutes for the line to be completely drained.

Notice how the pipe is gleaming at the very end?

The push fitting on one side of the filter assembly is inserted into the pipe to the extent that it will go, which is roughly 1 inch.

Holding the slip joint up to the pipe will allow you to get an approximate measurement of where you will need to cut the pipe on the opposite side of the installation.

To finish off the pipe, use a copper tube cutter to cut away any burrs on the end.

Once this is accomplished, while pushing the disconnect clip against the release collar on the slip end of the fitting, slide the fitting onto the second pipe such that the short copper tube is inserted into the assembly push fitting, once again to a depth of one inch.

Because our electrical system is grounded to the water line, which is a normal practice in many homes, we must attach this copper jumper wire, which functions as a bridge over the plastic water filter to ensure that the water flows properly.

This jumper wire is compatible with these clamps.

Now, let’s put our water filter into the cartridge and see how it works.

It also has the additional benefit of reducing other hazardous pollutants such as mercury and lead.

The housing is unscrewed from the head cap, and the replacement filter is inserted into the cartridge in accordance with the manufacturer’s recommendations.

We’ll manually tighten the cartridge by slowly twisting it in the opposite direction of the clock.

That’s exactly what I was looking for.

You may now receive a nice drink of filtered water from any faucet in the home.

It’s that simple. Not to mention the fact that it enhances the quality of the water that is utilized for other household activities. Our local independent home improvement store provided us with some DIY guidance, which was all it required. Transcript is now closed.

How to Replace a Whole-House Water-Filter Sediment Cartridge

Regardless of whether your water comes from a well or a municipal water source, you want it to be clear, clean, and of good flavor. However, this isn’t always true. So, other than stocking up on bottled water or shelling out a fortune for a state-of-the-art water filtration system, what can you do to combat this problem. An entire home water filter may be installed, which will supply clean, clear water for all of your household’s requirements. Installing this whole-house water filter is what we’ll be doing today.

  • After that, we’ll go through the many types of filters that may be utilized with our system, as well as the various levels of filtration provided by each type of filter.
  • Take the unit out of its packing and inspect it to ensure that we have all of the necessary components.
  • Preparing for assembly will take a few minutes now.
  • After that, we’ll screw the fittings into the head cap and tighten them tightly using an adjustable wrench, taking care not to overtighten.
  • While this 34″ mail threaded copper compression fitting would have worked, we would have had to connect the ends of the fitting to the existing water lines.
  • Remove the unit from service and open a faucet to alleviate pressure in the water line before putting it back in service.
  • In order to accomplish this, you will need to conduct some research and gain a knowledge of how water comes into your home from the well or municipal supply line outside.

Water purified for outdoor usage isn’t necessary in this case.

In order to have plenty of space to remove the cartridge for filter replacements, we’re placing our filter on a water line that runs towards the ceiling.

Remember to provide 1-1/2″ clearance below the housing in order to be able to detach it and change the filters.

Due to the fact that we don’t have any slack in the lines, we must employ a slip joint push fitting, such as these, which we have used in previous projects for the same reason as these.

This copper tube cutter will be used to make the initial cut in the current water line, which will be followed by the rest of the cuts in the pipeline.

To completely drain the line, it may take several minutes.

You can clearly see how the pipe is gleaming towards its conclusion.

The push fitting on one side of the filter assembly is inserted into the pipe to the furthest that it will go, which is roughly 1″ in diameter.

When you hold the slip joint up to the pipe, it will give you a good idea of where you will need to cut the pipe on the opposite side of the assembly.

To finish off the pipe, use a copper tube cutter to cut away any burrs at the end.

Once this is accomplished, while pushing the disconnect clip against the release collar on the slip end of the fitting, slide the fitting onto the second pipe such that the short copper tube is inserted into the assembly push fitting, once again to a depth of one inch.

Because our electrical system is grounded to the water line, which is a standard practice in many homes, we must attach this copper jumper wire, which functions as a bridge over the plastic water filter to ensure that it is not damaged.

These clamps are designed to accommodate this jumper wire.

Insert our water filter into the cartridge at this point.

Mercury and lead are among the additional dangerous pollutants that are reduced.

The housing is unscrewed from the head cap, and the replacement filter is inserted into the cartridge in accordance with the manufacturer’s directions.

We’ll manually tighten the cartridge by slowly twisting it in the opposite direction of the arrow on the cartridge.

See also:  How To Change Water Pump On Evinrude Outboard

That is exactly what I was looking for.

Not to mention the fact that it enhances the quality of the water that is utilized for other home purposes. Our local independent home improvement store provided us with some DIY guidance, which was all we needed. Transcript will be closed soon.

Why Use a Whole House Filtration System?

Oh, CULLIGAN MAN, how I adore you! When a home is powered by a properly treated private well or when your water has a high mineral and debris content, you may expect to find an excess of minerals, sediment, and even iron in your drinking, bathing, and cooking water, which will require filtration. It used to be that many individuals would purchase and install a whole-house filtration system specifically for this reason. When we came across one of these homes, we realized that it had been much too long since the sediment cartridge had been changed, so we decided to take on the job.

Changing a water-sediment cartridge was a rather simple procedure, even for inexperienced people like us; here’s how we went about it.

Water Filter Cartridge Replacement Guide

Once you’ve read through the textual preview of steps 1 through 7 described below, a picture-by-picture tutorial will walk you through the filter-change procedure one photo at a time, with easy-to-follow instructions for each photo. I recommend that you use safety goggles while working on the project since water can shoot directly into your face and may include particles from the caught silt from the previous filter. A bucket should be placed beneath the water-filtration assembly to capture any water that may leak out of the housing over the course of the project.

Preview of Project Steps 1–7

  1. Turn off the water mains and faucets. To relieve pressure, push the red pressure-relief button. Remove the handle from the ON or BYPASS position and unscrew the casing. Remove the huge O-ring and set it aside after wiping it clean. Remove the used filter cartridge and throw it away. Dish soap and warm water should be used to clean the housing. Completely rinse the dish. Fill the remaining third with water. To disinfect, add approximately 1 tablespoon of bleach and clean well. Thoroughly rinse the dish
  2. Clean silicone grease should be applied to the O-ring before it is reinserted into the groove. It is critical to ensure that the O-ring is seated level in the groove before proceeding. If this is not the case, the housing may not be properly sealed. Reinstall the replacement filter cartridge over the standpipe located at the bottom of the housing
  3. Screw the housing onto the cap and hand-tighten the screw threads. DO NOT TIGHTEN TOO MUCH. Check to see that the cap standpipe fits into the cartridge
  4. Then turn on the water supply. When using a valve-in-head device, slowly turn the handle to the ON position. To relieve the pressure, push the pressure-release button (if present). Before leaving the installation, make sure there are no leaks.

Important Information Regarding Your New Filter Change

Immediately after fitting the whole-house sediment-filter cartridge, turn on the water! It is necessary to run your house water for about 5 minutes after the filter has been replaced and the housing has been completely sealed before utilizing any of it. If you use tap water for drinking and bathing, it is a good idea to run it for approximately 30 seconds before using it for any other consumer use. If water sediments have made their way into your faucet system, it will be obvious as soon as the water starts to flow from your taps.

K9keystrokes to turn off the water supply

Step 1: Water Supply Off and Pressure Release

Turn off the water supply at the valve-in-head or the main water feed to the filter, whichever is more convenient. Release any built-up pressure by pressing the red button. Caution should be exercised since a torrent of water will shoot out when the release button is activated. WARNING: The red button may be used as an excellent prank on someone who is not aware of the water jet that comes out of the housing pressure-relief valve when it is pressed. Just make sure that everyone is wearing safety eyewear!

Step 2: Remove Housing and Clean O-Ring

Remove the huge O-ring from the housing unit by unscrewing it. The O-ring is located within the housing and seems to be a big diameter, but thin, black rubber band in appearance.

Remove the lens from the housing and wash it down with a soft cloth before setting the lens aside until you’re ready to reinstall it. Check to see if it is still in excellent condition; if not, place an order for a new one. K9keystrokes lubricate the O-Ring

Step 3: Dispose of Old Filter and Clean Housing

The big O-ring should be removed once the housing unit is unscrewed. The O-ring is contained within the housing and seems to be a big diameter, but thin, black rubber band in appearance. Remove the lens from the housing and wash it clean with a soft cloth before setting the lens aside until you’re ready to reinstall it. Check to see whether it is still in excellent condition; if not, place an order for a replacement. K9keystrokes: lubricate the O-Ring

Step 4: Lubricate O-Ring

Clean silicone grease should be used to properly lubricate the O-ring, making sure to cover both the interior and exterior surfaces of the o-ring. (It is critical to use a silicone-based grease for this application because silicone will not cause the rubber to swell or soften in the same way as a hydrocarbon-based grease will.) Replace the O-ring into its groove once it has been removed. Exercising extra caution to ensure the o-ring is correctly seated can prevent the seal on the housing from leaking, water pressure from degrading, and your water supply being exposed to germs.

K9keystrokes

Step 5: Install New Water-Filter Cartridge

Now it’s time to replace the filter. When you look into the housing, you will notice a standpipe positioned in the center of the base. It is a molded component in the shape of a circle with a short plastic-looking pipe projecting from the center (See photo5). It is critical that the filter be appropriately installed over this since this is the water access port, and as a result, this is where all of your water will be coming from for filtering before being delivered to your house taps. Make an effort to keep the filter centered on the standpipe.

Step 6: Screw Housing to Cap

By hand-screwing the filter cartridge to the cap, you may replace the housing with the filter cartridge. Make sure that the filter is centered over the cap’s standpipe before installing it. Despite the fact that you won’t be able to see where the standpipe is, you will be able to feel it glide effortlessly into the cartridge aperture. Caution should be taken not to overtighten the housing as this might cause it to break.

Step 7: Turn on Water Supply and Test Pressure

Turn the water supply back on by slowly rotating the intake lever. Caution should be exercised since if the water rushes in too rapidly, it might cause the housing to blow off and the unit to be destroyed. As a result, operate the intake valve gently and feel the pressure build up as it enters the housing so you can keep it under control until it fills. We replaced a filter with a valve-in-head device, but the same level of caution should be exercised with any water supply input that is utilized.

Water will rooster-tail out of the device, so be prepared to get sprayed a bit (or place a towel over the unit while conducting this step).

Be cautious to check that the seal between the housing and the cap is in excellent condition before leaving the unit. Water Filtration System for the Entire House K9keystrokes

Water-Filter Cartridge-Replacement Project Conclusion

After finishing the filter replacement procedure, we turned on the home water and let it run for a few minutes. When we turned on the faucets for the first time, a loud, strange noise erupted from the pipes. It was somewhat shocking at first, until we comprehended what had happened and what had caused it. Initially, the water seemed to be filthy and spit and sputtered sporadically for a period of time. Even simple tasks such as flushing the toilets and checking the shower provided this type of feeling.

Yet another unanticipated project on this historic property?” Eventually, we found that all of the banging and spitting had been caused by air that had gotten into the pipes during the construction process.

To the best of the author’s knowledge, the information in this article is accurate and complete.

India in the year 2011 Arnold On November 30, 2011, India Arnold (author) from Northern, California posted the following: dflood~ Double-check to ensure that the large black rubber gasket has been appropriately inserted and that the pressure valves (inlet and outflow) have been restored to their proper positions.

  1. Wishing you the best of luck!
  2. What exactly did I do incorrectly?
  3. The fact that you feel confident in your ability to change a whole home water filter after following the instructions in this article gives me great pleasure!
  4. Cheers On September 5, 2011, K9Chin chin from the Philippines posted the following: We had a water filtration system built beneath our kitchen sink to keep the water clean.
  5. I’ve never worked on it before, but with your hub tutorial, I believe I’ll be able to complete the filter cartridge replacement.
  6. India Posted on September 03, 2011 by Arnold (author) from Northern, California: PegCole Thank you very much!
  7. We found it to be rather simple and even enjoyable!

HubHugs On September 3, 2011, K9Peg Cole of North Dallas, Texas, posted the following: The information is well recorded and illustrated.

I have the impression that I am capable of doing this right now.

Wow, you’re absolutely correct!

Your comments have been really encouraging, and I appreciate you taking the time to read them.

Hopefully, you’ve been enjoying the plumbing contest, since your winning work has been a tremendous gift to the “how-to” community!

The bar has been set quite high!

India The following was posted on September 1, 2011 by Arnold (author) from Northern, California:HRoger Hey, Thank you very much for your thoughtful remarks and votes!

Thank you, K9HRoger, from wherever I am able to be!

on the first of September, 2011: Hello, K9. This is an outstanding HUB! Excellent facts presented in a unique manner! You’ve gotten all of my support: (1)Useful (1)Funny (1)Outstanding (1) (1)It’s beautiful (1)It’s interesting (1) Take care and keep up the good work!

How Often Should I Change My Whole-House Water Filter?

Many people who install new whole-house water filters or who move into a home with an existing water filter aren’t sure how to properly care for their new purchase. Here’s what you need to know. You’re well aware that you should replace it on a regular basis, but searching the internet to find out how frequently may be challenging. What is the solution? It is dependent on the situation. Varied filters have different criteria for how often they should be replaced, which can be perplexing if you are unfamiliar with whole-house water filtration.

To find out more, speak with a local plumber!

Typical Whole-House Water Filtration Schedules

The normal water filter will require replacement every 2-6 months. That’s quite a spread! So, how do you determine what your filter’s requirements are? Sediment filters in wells may only need to be replaced every two months. Carbon filters need to be replaced every 3-6 months depending on usage. Moreover, we recommend that you stick to the lower end of this range. If you wait six months, algae and mold may begin to form, thus it is preferable to act sooner rather than later.

Remember: It Depends

Despite this, the statistics might change greatly depending on the situation and the data. When a family of seven lives in a big household, more frequent filter replacements are required than when a couple lives alone. We have some further recommendations for anyone seeking for additional knowledge on the subject:

  • Customer service agents or the manufacturer’s handbook are good sources of information. Their knowledge will allow you to have a better understanding of when they recommend replacing a certain kind of filter. Make a phone call to a plumber. You can get your water treatment systems inspected and devise a timetable with your partner
  • If you detect a decrease in the quality of your water or a change in the pressure of your water, replace your filter.

Water filtration services for the entire house are available from Admiral Plumbing Services, LLC in North Palm Beach, FL and across the surrounding region. North Palm Beach, Water Filtration, Water Filtration At 11:00 a.m. on Monday, November 7th, 2016, Water Treatment Systems are categorized as follows:

How to Change a Whole-House Water Filter: A Step-By-Step Guide

A whole-house water filter is an excellent approach to enhance the overall quality of your water. Apart from improving the flavor of your water, a filter system also eliminates potentially hazardous bacteria, pollutants, and other disease-causing pathogens from the water in your house. A whole-house water filter, like most other equipment, requires regular maintenance to keep it from becoming clogged. Changing the cartridge of your water filter on a regular basis is a simple approach to guarantee that it operates at peak performance.

We’ll discuss that and how to do it without calling a plumber in this post.

Why Change Your Whole-House Filter?

Installing a whole-house water filter is rather straightforward; but, if you do not replace the filter stage or stages on a regular basis, the filter may cease to operate. Furthermore, if bacteria and mold are allowed to grow unchecked, they can constitute a major health hazard. As a result of the blockage, a buildup of chemicals and pollutants can cause harm to the filter. This can also result in reduced water flow and pressure in the pipes as a result of this. While water does occasionally pass through as predicted, there is a risk of health consequences if you drink any of the toxins in the water.

Failure to replace the filter cartridge on a regular basis increases the amount of damage done to the system, eventually resulting in it ceasing to function totally. Related: 7 Reasons Why Filtered Water Should Be Provided in Your Home

Tools and Supplies List

Prepare all of the tools and accessories that will be needed ahead of time to save time. If you are adequately prepared, replacing a whole-house water filter may be completed in a matter of minutes. Here’s what you’ll require.

  • Make certain that the new cartridge you choose is compatible with your whole-house water filter. There are many different types of filtration systems, so choose the cartridge that is specifically designed for your filter. You will need a wrench to remove the device from its mounting bracket
  • This is normally included with the kit and shipped with the filtration system when it is purchased. Remove the filter from the filter housing and place it beneath the filter to avoid spillage. Remember that you will not have access to clean water during the procedure, so prepare by filling two additional buckets in advance. Make soapy water in one of these to clean the interior of your whole-house water filter, which you will need to do later. Aside from that, household bleach is an optional ingredient. It has the ability to eliminate microorganisms that soap cannot
  • Always remember to use gloves and goggles to protect your eyes and face from splashes of water when working with water. It is possible that the water is polluted or contains solid residue that might cause damage.
See also:  How To Install Frigidaire Water Filter

Step-By-Step Guide to Replace Your Whole-House Water Filter Cartridge

Before you begin, set the empty bucket beneath the water filter to catch any runoff. Then, at the valve or main feed, turn off the main water supply to your house altogether. If you have an exterior valve, make sure you turn that off as well. Then, with caution, turn the red knob to release the pressure and drain any surplus water by turning on the nearest faucet. After that, prepare ready to take action.

  1. Using the wrench, remove the outer casing of your whole-house water filter and remove the O-ring from the filter. Make that the O-ring is in good condition. It depends on whether it is still in good condition or whether it is worn out and needs to be replaced. If the ring is still in good condition, you can clean it with soapy water or bleach. Make sure to oil the O-ring with silicon grease to prevent it from softening or becoming damaged throughout the process. If it appears to be damaged, it should be replaced before being reinserted into its groove. Remove the old filter cartridge and place it in the empty bucket to be disposed of. Then, using a little amount of bleach and soapy water, thoroughly clean the interior of the filter housing, which is particularly susceptible to germs. Following that, carefully rinse with fresh water. Final step: carefully wash the case to prevent harming it, and then set it aside to dry. Discover where your house water filter system’s standpipe is located within the dwelling. This round device with a small rubber mouth, which resembles a pipe, protrudes from the casing of your water filter and is attached to it. It is sometimes referred to as a water port. Incorporate the replacement cartridge into the housing, making certain that it is aligned with the standpipe in the middle. Screw the cartridge casing onto the cap, ensuring sure that it is still in the centre of the standpipe, and then remove the cartridge case. It’s important not to screw it on too tightly, otherwise it may shatter.

In order to reactivate the water supply, return the valve or intake to its original position. A fast rise in water pressure might cause harm to your whole-house water filtration system if you don’t proceed with caution and progressively turn the valves. Check for leaks thoroughly, and tighten any loose connections as soon as they are discovered. To ensure that air and any debris or residue left over from the filter replacement operation are removed from the faucet water before using it, let it running for a few minutes before using it.

How Frequently Should You Replace a Whole-House Water Filter?

The longevity of your whole-house water filter is influenced by a number of things. Depending on the size and kind of the water tank, the quality of the water may shorten its useful life. Depending on how polluted the water is in terms of sediment, metal content, hardness, and other contaminants, it is possible that you will need to replace your whole-house water filter sooner than planned. However, on average, most filters may survive for up to six months at a time; sediment pre-filters, on the other hand, require frequent replacement, but carbon filters can last for much longer periods of time before needing to be changed.

  1. Keep an eye out for physical clues such as hazy or strange-tasting water, which might be signs that your filter is blocked and has reached the end of its useful life.
  2. If it appears to be damaged or worn out, replace it with the next one sooner.
  3. Always test the water before installing a whole-house water filter or replacing a filter cartridge in an existing filter.
  4. Furthermore, always get a filter cartridge that has double the flow rate of the one that is needed.
  5. Additionally, if you are unable to locate a filter wrench, adjustable pliers can be used.

Leaks that occur after an O-ring replacement are almost always caused by the O-ring. To resolve this issue, either turn on the faucets or turn off the water valve to stop the flow of water. After that, check to see that the ring is securely set within its groove.

A Fairly Simple Process

And are you feeling confident enough to change your whole-house water filter without the assistance of a plumber? If so, read on. Providing you exercise caution and use protective clothes such as gloves, the procedure of repairing your water filter should be rather basic and quick. Replace a whole-house filter cartridge does not take much time or require any sophisticated instruments to do it efficiently and effectively. Ensure that you and your family are clear of water-borne diseases and that you are continually ingesting the purest, most pure drinking water possible.

Furthermore, if cartridges are not replaced appropriately, whole-house water filters might cause other water problems, which may need the replacement of the complete filter system.

How to Change a Whole House Sediment Filter

It is simple to replace a whole-house water filter, and doing so will save your family money in the long run. 1) Replace a whole house sediment water filter cartridge whenever the water flow in your home slows down, or after one year of usage, whichever comes first in your household. Bacteria shouldn’t be allowed to grow within that filter at any cost! Prepare a pail of clean, soapy water ahead of time since, after you open the filter housing, you will most likely be without access to water until the job is completed, so plan accordingly.

  1. You most likely have a shutdown on the supply line, which is positioned before the filter, installed.
  2. 3) Unscrew the housing that contains the water filter after releasing the water pressure in the lines.
  3. You can turn on a faucet inside the home to release pressure by allowing the water to run until it comes to a complete stop.
  4. In the meanwhile, place a bucket underneath the filter housing.
  5. Remove the housing by unscrewing it and pulling it out.
  6. Apply some clear plumbers silicone grease on the O-ring; this will assist to protect the O-ring, improve its seal, and make it simpler to remove the O-ring the next time it is used.
  7. Replace the housing by screwing it in little more than palm tight.

Slowly re-connect the main water supply to the house. Make a visual inspection for leaks around the cartridge housing. Then, with at least 3 or 4 liters of water, or until the water running out of the filter is clear, flush the new filter.

How to Change a Whole House Water Filter

An excellent strategy to preserve your family’s health while also improving the flavor of your water and giving you piece of mind is to install a whole-house water filter. However, once it has been placed, you must continue to clean the filter in order to prevent it from becoming clogged. In today’s article, we’ll show you how to replace the sediment filter or carbon filter in your whole-house water filtration system. Continue reading or find out more by contacting your local West Milford plumbers!

1) Be Prepared

Prepare your materials; the following is a list of things you’ll need:

  • The filter cartridge that has to be replaced
  • The wrench that is used to remove the filter housing (which, ideally, was supplied with your installation)
  • The filter housing itself A pail that is completely empty
  • A bucket filled with soapy water (remember, you won’t have water once you cut off the water to clean the filter, so be prepared).

2) Turn Off the Water

Turn off the water mains to the building. Locate the cutoff valve and turn it off to ensure that water does not pass through the filter when it is removed from the system. In addition, you’ll want to drain the pipes of as much water as you possibly can. Remove the water from a faucet someplace in your house and leave it running until the water slows down substantially. Afterwards, shut off the valve that leads out of the filter. Finally, push the release button on the filter housing to release any excess pressure that may have built up inside it.

3) Changing the Filter

A bucket should be placed beneath the filter area to capture the water that will leak out once the housing has been removed. Remove the filter cartridge from the housing by unscrewing it. This should be thrown out. Soapy water should be used to thoroughly clean the inside of the housing. Replace the filter and screw the housing back into place, tightening it a little more than you would have if you had done it by hand. Slowly open the water supply valve to avoid flooding. If you find any leaks, you should shut the valve down once more.

If nothing appears to be amiss, carefully open the valve going away from the filter until it is completely open.

4) How Often to Replace

Changing your water filter cartridge once a year or anytime your water pressure begins to decline is recommended. The presence of low water pressure or water flow suggests that your filter has become blocked. In addition, germs can accumulate in the filter after approximately a year, which is something you should prevent at all costs.

West Milford Water Filtration Specialists

Contact the plumbing professionals at Mark Lindsay and Son PlumbingHeating if you need help with whole-house water filtration or if you want to learn more about how to keep your plumbing system in West Milford running smoothly!

Whole House Water Filter Replacement

Difficulty:Simple Time allotted: ten minutes

SUPPLIES LIST | Whole House Water Filter Replacement

Locate the water main shutdown valve and turn it down to the lowest setting. Find your whole-house water filter, as well as the filter housing wrench, and set them aside. As a precaution, if you are using a well system, you should first turn off the well power before shutting the cutoff valve to prevent the well pump from pumping against a closed system if your main shutoff valve is ahead of the well pressure switch (if you are unsure, simply turn it off). Please remove any upstream water from the system if at all feasible prior to opening the water filter housing.

Our system features a drain located directly below the filter entrance, which makes it simple to drain any remaining upstream water prior to replacing the filter cartridge (see below image with white bowl).

A basement faucet or other low-level faucet can be used instead.

Preparing for the possibility of remaining upstream water by placing a collection basin or something similar under the water filter unit before it is opened is recommended.

  • Loosen Water Filter Housing and Replace The Water Filter
  • Disconnect the water supply, turn off the well pump (if you have one), and empty the system of any near upstream water. Unscrew and open the filter housing and remove the old filter while the system is still running. Cleaning the filter housing should be done prior to changing the filter. Between filter replacements, our filter housing gathers a substantial amount of sand and other debris. I prefer to sterilize the housing after washing it with a weak bleach solution and then rinsing it before putting in the new filter to ensure it is clean.

    Remove it by rubbing it on a moist paper towel and pulling it through.

    When installing the replacement filter cartridge, make a note of the filter’s location inside the filter housing and double-check that it is centered within the filter housing and that any gaskets on the filter cartridge are correctly aligned with the filter housing.

  • Re-assemble the Filter Unit, bleed air and check for leaks
  • Reassemble the filter housing into the filter unit head following the instructions provided. This may be accomplished by carefully aligning the threads of the filter housing and fitting unit head. Once the threads are engaged, manually tighten the threads until they are snug, then carefully tighten the filter housing wrench an additional 1/4 to 3/4 turn. The o-ring seal should be seated and gently squeezed to ensure proper sealing. Overtightening or tightening an o-ring that has not been lubricated might cause the o-ring to rupture and hinder a watertight seal.

    Remove air from the filter unit by pushing and holding the red bleed button on the top of the filter unit for a short period of time.

    It is best to dry the whole water filter housing with a clean paper towel first before feeling for signs of water leakage.

    IMAGE GALLERY | Whole House Water Filter Replacement

    Reassemble the filter housing into the filter unit head by screwing it down into the filter unit head. The threads of the filter housing and fit unit head should be precisely aligned in order to accomplish this. Using your fingers, tighten the threads until they are engaged, then gently tighten them an additional 1/4 to 3/4 turn using a filter housing wrench. A seat and a modest compression of the o-ring seal is required for proper sealing. An o-ring that has been overtightened or that has been tightened without lubricant might rupture and prevent a water-tight seal from being achieved.

    Air may be bled from the filter unit by pushing and holding the red bleed button on the top of the filter unit for a few seconds.

    Last but not least, turn the water back on and thoroughly inspect for leaks if any. Then I prefer to use a clean paper towel to dry the entire water filter housing, and feel around for moisture or signs of water leaks.

    Leave a Reply

    Your email address will not be published.