How To Lite A Water Heater

How to Light a Water Heater Pilot Light

Prev PostNext PostWhen the pilot light on a water heater goes out, it is typically because of a natural fluctuation in gas pressure, which extinguished the flame. The most obvious indicator that a pilot light has gone out is the one that everyone dreads: the water will not heat up properly. In the event of a damaged flame sensor, it’s critical to know how to relight the pilot light on your water heater so you can get the flame going as quickly as possible. This will not only allow you to get your hot showers back, but it will also ensure that no gas is unintentionally discharged into the home.

However, for the vast majority of gas-powered water heaters, you should begin by locating the gas shut-off valve on the water heater, which is generally plainly labeled on the front lower section of the water heater, before proceeding.

  1. Open the door or cover that provides access to the pilot light. In most cases, this will be positioned under the gas valve
  2. However, some water heaters will just have an open gap where you can see the pilot light burner instead. Locate the burner within the container using a flashlight or a headlamp. It will be reached by two little gas tubes. You’ll want to keep an eye on it while you’re at work. Turn the gas knob to the “Pilot” position and push and hold the button. This will initiate the flow of gas, allowing you to ignite the flame. Some water heaters feature a separate pilot mode button, which is commonly a red button, which you must push and hold in order to activate it. While keeping the gas pedal depressed, ignite the pilot light. Certain water heaters feature an igniting button that is red or black, while others must be lighted manually with a long lighter
  3. Some models include a red or black igniting button. Maintaining pressure on the gas knob or button for a full minute after the flame is ignited is critical. Then slowly release it while checking to see if the light is still on. Turn the gas knob to the “On” position and listen for the unmistakable “whump” or whooshing sounds that indicates the main burner has ignited. Enjoy your hot shower when you’ve replaced the lid.

Despite the fact that a single extinguished pilot light is normally caused by a natural fluctuation in gas pressure, recurrent faults suggest a more serious problem with the water heater itself. The most typical problem that causes repeated pilot outages is a filthy or bent thermocouple, which is a thin copper wire and rod that detects the presence of a flame and immediately switches the gas off when it detects a lack of flame detection.

What is a Thermocouple?

A thermocouple is sometimes referred to as a flame sensor in contemporary water heaters because of the way it detects flames. Your thermocouple is most likely twisted, filthy, or damaged if the pilot light continues to go out after you have completed the above-mentioned lighting procedures. For those who find that their pilot light is twisted and not near the burner, they may simply turn off the gas, shift it over, and attempt lighting the pilot again. It may be necessary to clean the water heater gas valve and the main gas line near the heater if this does not solve the problem.

  • The burner is typically simple to remove by simply sliding it out.
  • If this doesn’t solve the problem, you may get a new thermocouple for less than $15 at any hardware store or home improvement center.
  • Rooter Plumbing to help you get hot water back into your home again.
  • The use of hot water is simply one component of a great showering experience.
  • Previous PostNext Post Previous Post

How to Light a Water Heater’s Pilot Light (With Pictures)

With 23 years of experience in the HVAC sector, Dan has gained knowledge in a variety of areas, including installation, service, sales, and distribution. Some individuals may think that lighting the pilot on a hot water tank is an easy chore, but as a home service provider for over 15 years, I can assure you that I’ve made more than a few dollars executing this task for others. Despite the fact that many modern gas-burning appliances have converted over to hot surface or electronic ignition, there are still a significant number of standing pilot systems being made and used today.

It will be explained in detail in the following stages how to light your pilot, what to watch for when doing so, and a few other techniques you may use to get the fire started.

Author’s Qualifications

  • 15 years of experience in HVAC installation and service
  • 5 years of experience as a home improvement contractor
  • Product safety, performance, and certification testing experience spanning more than two years
  • EPAOSHA certification. Electrical theory, thermodynamics, and refrigeration coursework have been completed

This is an illustration of what a sealed combustion chamber on this sort of device may look like. It’s your looking glass, which is represented by this small square on the panel. Take note of the differences between this sort of control module and the earlier tank-style control module. In addition to being a control, the little knob on top serves as a button. View from above in order to notice the electrical spark button to the left.

Lighting a Sealed Combustion Pilot

We’ll start with a hot water tank system that is more contemporary and uses sealed combustion technology. With a sealed combustion chamber, there is no need to enter the burner assembly, and you should avoid doing so if at all possible. There is a looking glass in the access panel that you may use to visually verify if the pilot is lit. Everything you need to light this pilot is mounted directly to the burner control module. This access is bolted shut for a purpose, and it should only be accessible by individuals who are properly trained and licensed.

  1. Set the gas control knob on the top of the stove to the “pilot” position. To enable gas to flow, press and hold down the control knob itself for many seconds. Press and hold the electronic spark button, which is placed on or attached to your control module, until you hear it click. If there is a little amount of air in the line and it takes a few seconds to “bleed out,” you may need to click it a few times before the pilot is lighted. Continue to hold down the knob until the pilot has heated the thermocouple enough for it to be able to confirm ignition with the thermostat in the control module by visual confirmation. If the thermocouple does not heat up sufficiently, the pilot will be forced to return to the aircraft. Remove your finger from the control knob and visually check that the pilot is still glowing. To turn on the gas, turn the gas control knob to the “on” position. If the pilot was left out long enough for the water temperature to decrease, the burners should begin to operate within seconds of the pilot being turned off. If the water has not cooled, it is possible that there will be no need for the burners to be turned on. Be prepared for it to not start up immediately
  2. This is normal.

You are in the correct position if the notch is aligned with the button and the “pilot” is aligned with the indicator. The following is an illustration of what an open combustion burner assembly can look like. I’ve taken the two panels off so you can see what they look like on the inside. It is the copper line you can see in this shot that connects to the thermocouple, and the aluminum tubing that connects to the orifice where you will insert your lighter. Inside the room, the two come face to face.

Lighting an Open Combustion Pilot

Unlike the sealed combustion tank, you will be required to provide your own flame to light the pilot, rather than relying on an electronic ignition to do so for you. This process is very similar to the sealed combustion tank, with the exception that you will be required to provide your own flame to light the pilot yourself.

  1. The gas control knob should be set to pilot mode so that the notch in the dial corresponds to the button that controls the gas supply. If you do this, you’ll be able to press the button all the way down when it’s necessary
  2. Remove the panels from the burner compartments. Both should be quite simple to remove by raising up and pulling out. Place your preferred flame source (lighter, match, or other similar item) into the chamber such that the flame is directly beneath the aperture of the pilot supply line and ignite the flame. NOTE: I prefer to do three and then four. Despite the fact that the two stages can be exchanged, I believe it is better to introduce the flame before providing gas in order to minimize even the slightest possibility of gas buildup. I prefer to err on the side of caution, so I press and hold down the pilot gas supply button for many seconds before visually confirming that the pilot has been ignited. Keep the pilot gas supply button depressed for about 30-45 seconds to heat the thermocouple if this is the case. Release the button and visually check that the pilot light has not been extinguished. Assuming the pilot light remained on, turn the gas control knob to the “on” position.

Again, depending on your conditions, the water heater’s burners may or may not turn on straight immediately, so be patient.

Things You Can Use to Light a Pilot Light

  • A long, thin candle
  • A long, thin lighter
  • Long, thin matches
  • Short matches with a Hemostatic Clamp
  • A long, thin candle

Don’t Have a Lighter or Matches?

Lighting a long, thin candle on the stove and utilizing it to light the pilot light may be an option.

When doing this, place a piece of tin foil behind the pilot to prevent wax from spilling onto the bottom of the chamber.

A Quick Water Heater Inspection You Can Do

  • Check for moisture and corrosion in the surrounding area and at the bottom of the unit (a.k.a. blisters). This might be a signal to be ready for a new tank
  • For example, Check to ensure that your T P valve is operational. Feel the tank in your hands. Is it comfortable? If this is the case, you may want to consider adding an additional layer of insulation. Check the operation of your thermostat control. You may accomplish this by reducing the heat down to the lowest setting and turning off the burners, if any are already operating. It is expected that the burners will shut down at this point and that they will re-ignite within seconds of turning the burners back on. If not, your control may be inadequate, and you should seek professional assistance. Final question: “When was the last time I cleansed my water heater?” You may wish to ask yourself this question. This is something that should be done at least once a year.

To the best of the author’s knowledge, the information in this article is accurate and complete. Content is provided solely for informative and entertainment reasons and should not be relied upon as a substitute for personal counsel or professional guidance in commercial, financial, legal, or technical problems, unless otherwise specified. Dan Reed was born in the year 2012. Dan Reed (author) wrote the following on April 22, 2012: Thank you so much, Mmargie. People who have never done it before may be nervous, but I always spend a significant amount of time thinking about my directions and selecting themes that are safe for anybody to try if the instructions are followed.

I’ve always been apprehensive about using gas appliances.

lolI feel a little better after reading the particular instructions on your site, despite the fact that I do not currently have any gas appliances.

How to light a gas water heater

If your water heater is not heating up, it is possible that the pilot light has gone out. No matter what sort of water heater you have, the process of lighting it is straightforward. The majority of contemporary versions of gas water heaters are equipped with a straightforward ignition switch. The water heater is turned on in a matter of seconds, no trouble. If you’ve moved into an older home, on the other hand, it’s possible that your water heater is the type that requires manual activation.

Do you have a manual water heater?

There is a straightforward technique to determine if your gas water heater is automated or manual. Take a look at the box that protrudes from the side of the water heater and has two distinct dials. Automatic vehicles will feature a little ignition button adjacent to the large On/Off/Pilot dial, indicating that it is an automatic. If it is a manual, there will be no button to press. The On/Off/Pilot dial is normally located on the top of the box, whereas the temperature dial is typically located on the side of the box, as shown.

Taylor Martin is a contributor to CNET.

How to light an automatic water heater

The first step is to switch off the gas by looking for the knob labeled On/Off/Pilot on the control panel. You’ll want to move the knob past thePilot position and into theOff position. Allow for a five-minute dissipation of any built-up gas that may be present in the system. It’s time to start the lighting procedure at this point. Turn the water heat dial to Low and the On/Off/Pilot dial to Pilot to complete the process. Then, while simultaneously pressing the igniter button and turning the On/Off/Pilot dial down, turn the On/Off/Pilot dial up.

You should hear a “whoosh” sound as soon as the gas is turned on.

If it is lighted, conclude by closing the door and turning the dial fromPilottoOn, as well as changing the water temperature dial from Low to the temperature you like. To avoid gas accumulation, you must restart the process immediately if the pilot light is not lighted.

How to light a manual water heater

To fire this style of water heater, I recommend using a long barbeque lighter like this one. In any other case, getting in touch with the pilot will be difficult. To begin, remove the plate that is located beneath the dial-equipped box on the side of the water heater. There may also be an inner plate that you will need to shift to the side in order to complete the installation. Following that, you should notice a pipe or pipes heading to a burner. Then, in the box labeledOn/Off/PilotpastPilot, turn the knob to the Off position until it is completely off.

  • Turn the water temperature dial to the lowest setting and the On/Off/Pilot dial to the Pilot position.
  • Hold the barbeque lighter over the end of the pipe near the burner for a few seconds.
  • Continue to press thePilotdial downward for about 30 seconds, after which move the dial fromPilottoOn.
  • Important: If the burner does not come to life within a few seconds, repeat the operation until the burner does.
  • Is the energy efficiency of your home high?
  • CNET’s Guide to Smart Livingis a one-stop shop for tips, techniques, and how-to guides that can help you live a more intelligent life.
See also:  Where Is The Water Filter In Keurig Coffee Maker

How to Light a Water Heater

Documentation Download Documentation Download Documentation You may see cold water flowing from your hot water faucet if you reside in a home that has a natural gas water heater. This is a good indication that your pilot light has gone out. It is not necessary to hire a professional in most circumstances; you will have hot water again in a matter of hours if the pilot is re-ignited correctly. While having your water heater’s instruction manual on hand is a good idea, it is not fully required because most gas water heaters need a similar process for relighting the pilot light, as described in this article.

  1. 1 Make that the pilot light is working properly. You will most likely need to remove a tiny panel at the bottom of the tank, known as an access panel, in order to determine whether or not the pilot light is truly turned off. If you do not see a little flame flickering, this indicates that your pilot light has failed.
  • Depending on your water heater model, it is conceivable that your panel is not detachable and that you must observe your pilot light via a transparent window. It is possible that your pilot light has gone out if you are unable to see a flame burning through the glass in this situation.
  • 2 Check to see whether there is any gas leaking. Never attempt to restart your pilot light if there is gas leaking from your water heater, as this is highly harmful to both you and your property. Instead, call 911 immediately. If there is any evidence of leaking, perform a basic smell test before trying to ignite the pilot again.
  • Standing near to your water heater, sniff the air to see if you can notice any strange aromas. After that, get down on your knees and smell around any valves on the front and sides of the tank. Naturally, natural gas has no odor. To make it noticeable to humans, gas companies add an ingredient known as mercaptan to the mixture. When gas leaks, it has a sulfuric or rotten egg smell to it
  • If you notice gas leaking in either of these locations (even in a faint scent), do not attempt to relight the pilot light. Remove yourself from the vicinity of the water heater and contact your gas provider immediately
  • They will advise you on what to do next. Also keep an ear out for a hissing sound near the water heater, which might indicate a gas leak
  1. Advertisement
  2. If your water heater has a door panel, look inside it for installation instructions. Specific installation instructions and specifics for your unique model may be mentioned here, and they may be of assistance in the process of relighting the pilot for your specific water heater.
  1. Step 1: Lower the temperature control setting to the lowest possible setting. 2Find the regulator valve, which is normally situated on the front of a box on the outside of the water heater
  2. 3Find the pressure relief valve. In most cases, this valve is positioned on the same box as the temperature control, but it is more likely to be on top of the box
  3. It regulates gas flow to the pilot burner beneath the hot water tank. To turn the knob off, turn it to the “Off” position. Wait 10 minutes after turning off the knob before proceeding to ensure that any remaining gas from the tank has cleared the air before continuing. The importance of safety cannot be overstated. 4 Determine the type of water heater that you have installed. Gas hot water heaters are often classified into two categories: “new” and “ancient.” Traditional heaters will require you to relight the pilot with your own flame, however newer design tanks are fitted with a pilot light igniter built in into the tank.
  • However, while the specific appearance of the buttons on modern design tanks may vary, many of them include a red igniter button that is located a few inches away from the temperature and regulator valves.
  • 5 Gather any lighting items that may be required. The pilot light on an old-style water heater must be re-lit with a “wand” lighter or fireplace matches since the pilot is too lengthy to reach with a standard lighter.
  • Please avoid re-igniting a pilot using a standard lighted matchstick or miniature cigarette lighter, since doing so will force you to place your fingers in a small, tight position too near to the open flame, putting you at risk of being burnt
  1. 6Travel to the location of the pilot. The pilot is positioned at the end of the little silver tube that comes out of the control valve and is connected to the control valve. It’s possible that you’ll need to use a flashlight to see clearly in this location. Advertisement
  1. First, put the gas valve to the “Pilot” position by pressing down on it with your finger. Starting the flow of gas into the tube that provides the pilot light is accomplished in this manner.
  • Find a red control button near the gas valve on your water heater if the gas valve on your water heater does not press down properly. Hold this button down for a moment.
  • 2 Light the pilot burner with a match. The pilot gas valve or the red button will be held down with one hand while the other hand will be used to swiftly light the pilot.
  • To use this button, make sure you have a new model water tank with a built-in ignition switch installed. You should be able to hear a clicking sound until the pilot burner comes on. If you have an old-fashioned heater, ignite the pilot burner with a wand lighter or match and wait a few minutes. Because you will be using one hand to push the valve/red button while using the other hand to ignite the pilot, you may require the assistance of another person to carry a flashlight for you if you require additional lighting. Make an effort to get assistance in advance so that you do not go halfway through a procedure only to be forced to halt because you are unable to see what you are doing
  1. 1 Minute after the pilot light has been ignited, keep the gas valve or control button down by pressing it down one more time. In this case, the thermocouple will be heated, which is a sensor that turns off the gas when the pilot is not lit. 4Remove the valve knob/control button from the valve. Check to check if the pilot light is still illuminated after a minute by releasing the valve and pressing the control button. 5Replace the access panels with new ones. When checking to see if the pilot light is still glowing, replace the access panel (if you had to remove it first) to ensure that no flames are escaping into your home. 6Re-ignite the main burner if necessary. Turn the main gas valve back to the “On” position and set the temperature control to the appropriate temperature. The main burner under the tank should be turned on and the water in the tank should begin to heat. When turning the knob to “on,” take care to keep your head away from the burner area. 7Set the thermostat to the temperature you wish. Remember not to heat the water to a boiling point, since you might scald your hands or body accidently when washing or bathing. The Consumer Product Safety Commission recommends a temperature of 49 degrees Celsius (120 degrees Fahrenheit). Advertisement

Create a new question

  • QuestionHow can I start a newer model gas heater that is on the market? Look up your model number and get in touch with the manufacturer for more detailed information. As a general rule, the most significant difference between a modern heater and these instructions is that newer types feature an electronic igniter (you simply press the button and a spark is produced) for lighting the pilot. Question What do I name the gadget that I use to ignite the pilot’s engine when I press a button on it? You refer to it as a “spark igniter.” Question What should I do if the pilot light on my water heater keeps flickering on and off? It is likely that you will have to replace it. Make contact with a supplier or even the firm that produced your water heater for further information. Question What should I do if the pilot light won’t remain lit for whatever reason? The most likely cause of your problem is that your thermocouple has to be repaired or replaced. A pilot light is a short copper tube that connects your water heater’s controls to the pilot light and has an end that sticks into the flame. Whenever the pilot light heats up the tip, it creates electricity that is detected by the control box, which allows it to determine that the pilot light is on. A new one is simple to install, and you can pick one up at any home improvement, plumbing supply, or hardware shop. Take your old one with you so that you may acquire the right measurement. A little bit longer is OK, but not typically much shorter
  • Question When I press the pilot button, how long should I hold it down before pressing the little red ignitor button beneath it? It takes around 5 seconds. Restart it and make any necessary adjustments to the temperature. Question So, what should I do if the pilot light won’t turn on for whatever reason? Continue to try while keeping an eye out for any signs that there is gas coming through (usually by smell). The likelihood is that the regulator is faulty and that it will need to be replaced. This is also something that you can accomplish on your own.

Inquire about something There are 200 characters remaining. Include your email address so that you may be notified when this question has been resolved. SubmitAdvertisement

Video

  • If this procedure does not provide results, check to see that the pilot light’s base is not filthy or blocked. If it is, clean it well and repeat the process after 10-15 minutes. You may also try holding the valve/control button for an additional 30-45 seconds after the pilot light has been ignited. If this technique does not work, it might be due to a lack of gas pressure or a defective gas valve. If you are unable to light the water heater after many efforts, contact an appliance repair person, a plumber, or your gas provider. You may have a faulty thermocouple if the pilot light does not come back on after being re-lit or if it goes out soon after being re-lit. It is possible to see the thermocouple in the pilot light flame region because it extends from the temperature control into the flame area. The cost of one is pretty low, and you can do it yourself.

Thank you for submitting a suggestion for consideration! Advertisement

  • If you detect the scent of gas anywhere in your home, contact your gas provider right once. Even a “little quantity of gas” is too much
  • Do not re-open the gas valve until you have completed the replacement of the access panels and doors. It is possible that a flame will come out of the water heater if this is done.

Advertisement

About This Article

Summary of the Article Set the temperature control to the lowest setting and turn the gas regulator valve to the “Off” position to begin lighting an electric water heater. X Then, by adjusting the gas valve to the “Pilot” position and pressing down on it, you may begin to pump gas into the system. After that, press the red ignitor button, which is located near the gas valve, to ignite the pilot burner. Hold down the pilot button for 1 minute longer than you think it should be and check to see whether the pilot is lit.

Continue reading for helpful hints on how to prepare for and light your water heater. Did you find this overview to be helpful? The writers of this page have together authored a page that has been read 388,914 times.

Did this article help you?

When one of our customers, Theresa, requested that we give some basic instructions on how to securely relight the pilot light on a gas water heater, we gladly obliged. Theresa, thank you for your proposal; we are pleased to assist you.

Step 1

Turn the dial on the gas valve to the “Off” position and wait a few minutes.

Step 2

Turn the gas valve to the “Pilot” position and depress the valve button (or, instead, if there is a red button beside the valve, push it down). Maintain pressure on the button to begin the flow of gas via the gas supply tube.

Step 3

Continue to press the button down and wait for the indication to light up on the screen. Some water heaters need the use of a manual light switch. If this is the case, fire the gas at the end of the supply tube using a grill lighter.

Step 4

Maintaining the hold on the control button for another minute or two after the pilot is lighted is recommended. Then press and hold the control button for a few seconds.

Step 5

Alternatively, if the pilot continues to glow after you remove the control button, set the dial to “on.” If the pilot goes out again or if the light does not come on, start over at Step 1 and repeat the procedure. It’s quite OK to give something a couple of tries. However, if your pilot won’t light or won’t stay lighted after a few of tries, it’s better to contact a professional for assistance.

See also:  How To Relight Pilot Light Water Heater

How To Light The Pilot Light on Your Hot Water Heater

If you have a gas water heater, it has a pilot light that must be kept lighted at all times. If you don’t, you’ll be without hot water for quite some time. If it does go out, don’t be concerned; re-igniting it is simple. Simply follow the instructions outlined below.

Before You Start

Grab a flashlight and a wand lighter to help you out. If you have a recent water heater, it is likely that it has an electric light integrated into it as well. Then, using your nose and ears, check for any leaks that may have occurred. If you notice any unusual odors or hear a hissing sound, don’t go any farther and call IT Landes in Harleysville, Pennsylvania right now. We’re specialists in everything related to water heaters, and we can come out right away to take care of any problem. Finally, look inside the device for instructions on how to turn on the pilot light, which should be located on the inner panel.

If this is the case, the actions that follow are typically relevant to the majority of water heater units.

Adjust the Temperature Control and the Gas Valve

Turn the temperature control down to “low” and turn off the gas valve for a few minutes to remove any leftover gas that may have accumulated in the appliance. Then, set the gas valve to the “pilot” position.

Find and Light the Pilot

Open the access cover and look for the pilot, which should be visible protruding from the control valve when the cover is closed. Grab the wand lighter and squeeze the gas valve to start the engine.

Next, while the valve is still held in the closed position, ignite the pilot. For approximately 20-30 seconds, continue to hold down the gas valve before releasing it. The process should be repeated if the flame goes out, and the gas valve should be held down for 45 seconds to 1 minute.

Final Steps

Once the pilot light remains on, switch the valve from “pilot” to “on,” replace the access cover, and adjust the temperature dial to your chosen setting. IT Landes has been in the heating, ventilation, and air conditioning sector since 1929. We’ve achieved an A+ rating from the Better Business Bureau as a result of our dedication to client satisfaction. Aside from that, we were named winners of Carrier’s President Award for quality leadership and achievement in 2019. Whether you want assistance with your water heater, ducts, furnace, or plumbing, we are here to help.

Light Your Hot Water Heater Pilot Light in 5 Easy Steps

Posted at 12:00hinPlumbing Services on February 12, 2019 There are a variety of reasons why your hot water heater’s pilot light may go out. However, while the absence of a pilot light may signal a problem with the heater itself, a hot water heater pilot light can also go out for a variety of other causes, such as oscillations in the gas pressure. If your pilot light is out, you will most likely see cold water flowing out of your hot water valves when you turn on the water. The good news is that you can easily re-ignite your hot water heater pilot light by following these five simple steps:

1. Turn Off the Gas

The first thing you should do is make certain that the gas has been turned off completely. Locate the gas regulator valve in order to accomplish this. On the outside of your water heater, around the point where the main gas line enters the heater, you’ll often find this valve. Allow at least five minutes to pass after turning this valve to the “off” position to allow any leftover gas to disperse.

2. Where is The Pilot Light on Hot Water Heater?

This section will most likely necessitate the use of a flashlight. Most of the time, the pilot light for your hot water heater may be found beneath the water tank on your device. It is possible that you may need to remove an access panel in order to get to it. Some newer versions may have the pilot light hidden behind a glass panel, which is a nice touch. In appearance, the pilot light’s housing should be in the shape of a little silver tube. You will need to hire a plumber to diagnose any additional issues you may be experiencing with your water heater if there is already a flame burning at the end of this tube when the pilot light is turned on.

3. Check for any Gas Leaks

Ensure that there are no gas leaks or residual gas before proceeding any further. Igniting a flame in the vicinity of a gas leak can be extremely hazardous to your health and the safety of your property. Relighting your hot water heater pilot light should only be done if you are certain that no gas is leaking from the device. You may confirm this by doing a basic smell test as follows: Take a few deep breaths while standing near to your water heater and smelling the air. Despite the fact that natural gas is odorless, gas companies use an additive called mercaptan to guarantee that it may be discovered in the event of a leak.

If you don’t detect any rotten eggs-like odors in the air surrounding your water heater, step closer and sniff any of the valves, pipes, or connection points in the vicinity of the unit.

Immediately leave the house if you detect even a faint whiff of gas and contact your plumber, who will be able to advise you on what steps to do next.

When you leave the house, avoid turning on or off any lights since this might cause sparks that could ignite the gas.

Always leave the house before phoning someone or sending a text message. Natural gas that is leaking can make you sick, and spending any further time near a gas leak increases your chances of accidently inhaling or igniting the leaking gas.

4. Ignite your Hot Water Heater Pilot Light

It is safe to restart your hot water heater pilot light once you have determined that there are no leaks in your water heater equipment. To accomplish this, set the regulator valve to “pilot” and press and hold it down for a few seconds. Depending on the model, you may be required to press a second red button to regulate the flow of gas to the pilot light. If your machine includes a dedicated pilot button, it will most likely be red and labeled “pilot.” Check the front of your unit for instructions that may assist you in locating all of the valves and buttons necessary to re-ignite your hot water heater’s pilot light, if there are any.

When it comes to newer models, the “ignition” button on your water heater should be either black or red in color.

As this occurs, you should hear a clicking sound.

The safest method for accomplishing this is to use a long-nosed lighter, such as those used to ignite barbecue grills.

5. Make Sure the Flame Stays Lit, and Your Heater is Working.

Maintain pressure on the regulator valve for at least a minute after the pilot light has been ignited. The thermocouple sensor will be able to re-heat as a result of this. This sensor detects whether your water heater’s pilot light has gone out and will shut it down if the water becomes too cold to handle. Allow for a minute before carefully releasing the regulator valve and checking to see whether the pilot light continues to burn. If this is the case, switch the regulator valve to the “on” position.

Once this is accomplished, your pilot light should be operational.

Final Thoughts

Dealing with natural gas may be a frightening experience. It is possible, however, to safely rekindle your hot water heater pilot light whenever you need to if you follow these simple instructions. It’s always possible to call Benjamin Franklin Plumbing for skilled, timely, and locally-based assistance if you are still unclear of what you are doing, cannot figure out how your specific model works, or simply prefer to have a professional handle the situation instead. BFP Duncanville provides plumbing services to the Southwest Dallas communities of Cedar Hill, Dallas, DeSoto,Duncanville, Glenn Heights, Grand Prairie, Maypearl and Midlothian as well as the towns of Oak Cliff and Ovilla.

In addition to emergency plumbing repair, the company offers a variety of other plumbing services, including faucet repair, drain services, toilet repair, plumbing fixture installations, tub and shower installations, kitchen sink repair, faucet installation, water heater repair/replacement, and garbage disposal replacement, among other things.

For further information or to make an appointment, please contact us at (972) 263-5010.

How to Relight the Pilot Light on Your Water Heater

Several factors might contribute to a pilot light on a water heater being turned off. The front of most water heaters will contain instructions on how to relight the pilot light, and this will usually be on the right side of the water heater. The first step is to turn off the gas to your water heater by turning off the gas control valve on the tank. Then follow these instructions to re-ignite the pilot light on your water heating system:

  1. Remove the access panel for the water heater
  2. Check to see if the gas valve is open (on most valves, this indicates that the valve is in line with the pipe)
  3. And Make sure that the gas control valve on the water heater is in the pilot position. Hold the knob on the front in and press it in. For a flame to emerge on the screen, hold down the ignitor button (the black square button below the knob). Keeping the knob pressed in until the indicator light starts blinking is recommended. Using the knob, adjust the temperature to your liking.

The flame should be visible via the viewing window if you look closely enough. That indicates that your pilot light has been turned on. Although the gas control valve on your water heater may be different, the process of relighting it should be very similar. You may look up “How to relight a _” on Google and fill in the blank with the name of the brand of your water heater to see what comes up. YouTube is another excellent source of information. Gas control valves come in a variety of shapes and sizes, and they might be installed on your water heater.

If you are unable to relight your pilot light, or if it does light but continues going out on you suddenly, contact a plumber you can trust for assistance in determining what is causing the problem.

Tips to Keep Your Water Heater Pilot Light Healthy

Get in Touch With Us At the end of the day, dinner dishes are piling up in the sink; laundry has to be done; and you are in urgent need of a hot shower. All of these things need a properly operating water heater, which implies that the pilot light must be in good working order. A malfunctioning pilot light on your water heater may have a significant impact on the entire family if it is not maintained properly. It is possible that the pilot light may go out, resulting in only cold water coming out of your taps since the appliance will be unable to switch on to heat the water if the pilot light goes out.

  1. What is the appearance of the pilot tip? The pilot light is powered by gas that is channeled into the tip of the light. A supply line that is linked to natural gas or propane provides the gas for this appliance. Over time, the tip may acquire gunk, which is composed of dirt and residue, and this gunk may begin to obstruct the flow of gas. Keeping the pilot light tip clean at regular intervals is essential for it to function properly and to perform its duties completely and at full capacity. Using a needle, flexible wire, or even a toothbrush, you may remove the built-up junk from the pilot light device after it has been turned off and allowed to cool for a while. About every six months, we recommend that you check your pilot light for residue. Also, make sure you have enough gas. Has it been difficult for you to maintain the flame of your pilot light? One theory is that there is a shortage of natural gas in the country. If your pilot light is not getting enough gas to burn, it might cause the light to flicker, which can result in an inefficient water heater, according to the manufacturer. You should periodically check the gas level in your reservoir to ensure that the pressure gauge on your supply is accurate. However, occasionally when your supply diminishes, the pressure decreases as well, which can be dangerous in some situations. Another possibility is that the tube connecting the gas source became kinked, necessitating the installation of new tubing. How well is the thermocouple performing? Thermal couplings are used in water heaters. They function in conjunction with the pilot light and are responsible for determining whether or not it is hot enough to activate the gas or propane burner and ignite the water heater. To provide hot water to your house, the pilot light and thermocouple must operate together
  2. However, if the thermocouple isn’t functioning properly, it will not identify the heat from the pilot light and therefore will not open the valve to allow the water to heat up. Consequently, because it is a partnership, they both must be in excellent operating condition for your water heater to produce hot water throughout your home. Things can happen to a gadget after it has been in operation for an extended length of time, just as they might with any other equipment. Consider the following scenario: if the thermocouple becomes bent for any reason and bends too far away from the pilot light, the heat from the pilot light will not be detected. This should be close enough to the thermocouple that it can feel the heat, and it should be gently contacting the thermocouple to check that they are correctly functioning together. What color does the flame appear to be? In order to be healthy, the pilot light should have a vivid blue hue. Whenever the flame becomes more yellow or orange in hue, it indicates that there is a problem and that something is not functioning properly. The color of the pilot light is always an indication of how effectively or inefficiently it is burning at any one time. It is because of this that the pilot light and thermocouple have formed a partnership once more, since when the thermocouple senses a problem, it will go into protective mode and extinguish the flame and close the valve.
See also:  What Temperature Should Your Water Heater Be Set At

The pilot light works quite hard, and despite the fact that it is a little light, it performs a significant function by ensuring that you have enough warm water for cleaning and domestic duties. It is important to do the necessary maintenance and inspections on your household appliance in order for it to remain healthy and robust.

Call The Plumbing Joint for Repairs

You may reach the Plumbing Joint at (425) 279-7029 for assistance if you see any of these difficulties or suspect any other plumbing or drain problems in Seattle, Tacoma, Bellevue, or Renton, as well as many other neighboring regions.

7 Reasons Your Water Heater Pilot Light Keeps Going Out

There is nothing more inconvenient than stepping into a frigid shower to begin a chilly day. It’s possible that you’ve recently found that the pilot light is constantly going out. Thousands of consumers are dissatisfied with their water heaters, which fail to function properly only a few months after installation. Is it usual for your water heater to go out on you in the middle of the night?

No! Your heater should be able to easily reach the 10-year milestone without experiencing any serious problems. Only a few number of manufacturers are capable of creating water heaters of such high quality. Take a look at these beautiful water heaters in Phoenix.

What Is The Pilot Light?

The Pilot Light is the heart of your water heater, and it controls the flow of water. Essentially, it is a little blue flame that produces heat by burning petroleum gas. There would be no heat and, hence, no warm water if this flame were not present.

So, What Are The Reasons Your Water Pilot Light Keeps Going Out?

Not only will we identify the potential issues, but we will also provide you with solutions to those issues. Please take notice of the following: Check to see whether your water heater is still covered by the manufacturer’s warranty. If this is the case, it should be returned to the supplier or manufacturer for repairs or complete replacement. Precautionary measure: To begin, shut off the main gas supply valve to prevent potentially fatal gas leaks. Wait 5 minutes for the heat and gas to dissipate before continuing.

1. An Unclean Pilot Tube

It’s a problem that practically all water heaters have at some point. Please don’t be concerned, your heater is in perfect working order. It’s simply a buildup of dirt. The Pilot tube is responsible for supplying gas to the pilot light in order for it to burn. if the tube becomes blocked with dirt or other particles, the flame will go out. It is possible that the tube is partially blocked and only supplying a little amount of gas for combustion—which explains why your pilot light keeps going out.

To gently clear the tube, use a thin needle to poke it with.

You must be patient during this process.

Place the container back where it belongs and turn on your water heater.

2. A Dirty Thermocouple

In the case of a water heater, the thermocouple serves as its brain. It is in charge of shutting down the gas valve when it detects that the pilot light has gone out. Because the pilot light produces an electric current, the thermocouple is activated when this current is present. It serves as a safety measure, preventing gas leaks from occurring. As a result, a filthy thermocouple might be the source of your water pilot’s inability to function properly. When a coating of filth and dust accumulates on the surface of a thermocouple, the electric current cannot reach it.

On a chilly Monday morning, there is no hot water.

To begin, shut off the main gas supply valve and allow the thermocouple to cool before proceeding.

3. A Kinked Thermocouple

As soon as you’ve finished cleaning, double-check the location of the thermocouple. Also, look to see whether it’s a little bent. The thermocouple must be placed close to the pilot light in order for it to receive heat and activate the gas valve. As a result of being too far away, heat will not be received and an electric current will not be generated. The thermocouple will determine that the pilot light has been turned out and will seal the valve, cutting off the gas supply to the house. The answer is as follows: First, turn off the gas and turn off your heater, and then wait for the thermocouple to cool down before proceeding.

You’ll have to bend or straighten the thermocouple manually to get it back into position. To be effective, the blue flame must be placed close enough to the pilot light so it contacts or wraps around the blue flame.

4. A Broken Thermocouple

So, you’ve cleaned and straightened your thermocouple, but your water pilot continues to fail despite all of your efforts. You should be prepared to accept the possibility that your thermocouple is faulty at this point. Perform a diagnostic test with a multimeter on your thermocouple first, though, before you give up on it. If the voltage delivered by your thermocouple is significantly less than 20MV, then the device is almost certainly damaged and should be replaced immediately. The Solution: If the multimeter reading is near to, but not exactly at, 20MV, you can adjust the thermocouple closer to the pilot light to save energy.

5. Flex Tube Issues

Flexible tube is a long tube that links the gas controller to the burner, which contains the pilot light, thermocouple, and other components. If the flex tube is broken or blocked, the gas will not be provided to the burner for combustion to take place. Flex tube failures, on the other hand, are not as prevalent as thermocouple failures. This is why you must first inspect and ensure that your thermocouple is in excellent working order before turning your attention to the flex tube. The Solution is as follows: Straighten any kinks in the flex tubing that have formed.

Leaks in the gas line will lower the amount of gas that reaches the burner.

6. A Faulty Main Control Valve

It’s possible that you’ll never run into this situation again. We recommend that you examine the pilot tube, thermocouple, and flex tube before attempting to modify or repair this piece of equipment. The Main Control Valve Unit has a very low failure rate. However, don’t count it out just yet; it’s possible that it’s the source of your water pilot’s incessant failure. Main Control Valve: This valve is in charge of regulating the gas and water pressures of the water heater. Your water heater’s heart and soul is the thermostat.

When the gas is ignited, the main valve is fully opened, allowing for a consistent stream of gas to be provided.

The following are signs of a defective main control valve:

  • A malfunctioning pilot button that does not illuminate after being pressed
  • A malfunctioning control knob
  • When the water temperature exceeds the stated range, you will feel extremely hot water.

The solution: There is no way around a defective main control valve in this situation. However, despite the fact that there are specialists who say they can fix this, manufacturers highly advise against it. It is recommended that you replace the item to prevent incurring more expenditures and causing damage to other components of your water heater.

7. Poor Electrical Wiring

When it comes to electric water heaters, this is generally a concern. The fact that you should always engage a professional to install your water heater is one of the main reasons for this.

If your water heater suddenly stops working, this is the first indication of a defective electrical system. The Solution: Turn off your water heater as soon as possible and contact a professional. Please do not tamper with the electrical wiring system.

Our Final Word

If all of your methods fail and your pilot light continues to go out, it’s time to call in the heavy guns (the professionals). We’re aware. We’re aware. The services of technicians are not cheap, but at the very least you will have greater confidence in the repairs. In addition to that, we are all aware of the dangers associated with electricity and natural gas. Your safety is of the utmost importance. Did you find this information useful? Check out Why Are Trane HVAC Units So Popular? for more information.

How to Light an RV Water Heater Pilot (3 Simple Steps)

In modern recreational vehicles, you may turn on your gas-powered water heater by simply turning on the ignition switch. Older versions, on the other hand, need you to manually ignite the pilot in order to get your water heater to work. In this fast guide, you’ll discover how to light the pilot light on an RV water heater in three easy steps. In addition, some key guidelines to follow to guarantee that your water heater is not harmed in the process.

How to Light Your RV Water Heater Pilot

The procedure of igniting the pilot light on your RV’s water heater is quite straightforward. All you’ll need is a long utility lighter or a long match, and you’ll need to follow the methods outlined below. But, before we can really ignite the pilot’s lamp, there are a few things we need to take care of.

Important: Before Attempting to Light an RV Water Heater Pilot

  • Please check to see that your freshwater is switched on, and that your water heater tank is filled with water! The use of a hot water heater while the tank is empty might result in expensive damage
  • If you have just filled your water system, turn on the taps to bleed the air out of the water pipes
  • Otherwise, turn off the faucets. Check that your propane tank is operational by turning on the LP gas valve. Once again, double-check that your hot water tank is completely filled with water! If it isn’t, fill it in before proceeding. If you’re experiencing trouble, have a look at our tutorial on how to fill an RV hot water heater for some helpful hints.

Now is the time for us to turn on the pilot light on our water heater. We’ll go through how to start the pilot light on an Atwood RV water heater in an old 1980s recreational vehicle. Other RV water heater types that require manual lighting follow a procedure that is essentially the same or very similar. Let’s get this party started! Pilot light for an Atwood RV water heater

Step 1: Turn the Pilot Light Knob to “Pilot”

We must first change the setting of the knob from “Off” to “Pilot.” On the Atwood model seen in the image above, you must then turn the knob past “Pilot” and keep it in that position. A slight spring tension will be felt in the knob when it is tightened. For a different model, such as an old Suburban water heater, you will most likely need to press the knob down and keep it in place after switching it to Pilot mode, as seen in the picture.

Step 2: Light the Pilot Light

We are now ready to manually ignite the pilot light using a match. Simply take your long utility lighter, light the flame on the lighter, and place it next to the pilot light to begin the process. Please keep in mind that it may take up to 30 seconds or more for the pilot to ignite. When the pilot light is turned on, you’ll notice a little blue flame.

Step 3: Turn the Pilot Light Knob to “On”

To switch on the pilot once it has been lighted, turn the pilot setting knob from “Pilot” to “On.” The pilot flame will develop fast and make a loud noise, similar to that of a jet engine taking off. This is quite normal. You may now modify the temperature of the water to your preference. Congratulations, you’ve successfully ignited the pilot light on your RV water heater. Now, take a good, hot shower to refresh yourself (after letting the water heat up, of course). Tip: If the pilot light on your RV water heater won’t remain lit, it might be due to a faulty thermocouple, an inappropriate air/gas combination, insufficient propane pressure, or other factors.

If this does not resolve your problem, you may need to take your RV to a trained RV technician.

As an example, if you have an old Suburban RV propane water heater, this fast video will lead you through the entire procedure of igniting the pilot light.

4. How to ignite the pilot light on an RV water heater Clearly, the procedure is quite similar to that used to light the pilot on the Atwood RV water heater in the previous section. Is it a good idea to leave my RV’s water heater running all of the time? (Important)

FAQs

Most current RV water heaters do not employ standing pilots anymore, instead depending on electronic igniting to ignite the tank. If your water heater has an electronic igniter, do not attempt to manually light the pilot light. This is for your own safety.

Can I Light My RV Water Heater With a Lighter?

Using a lighter (or a match) to ignite the pilot on an older RV water heater will be necessary if you have one of those models. For newer models equipped with an electronic pilot, you will not be need to use a lighter to ignite the pilot flame.

How Do You Turn On an Electric Water Heater in an RV?

In most motorhomes, the On/Off switch for the electric water heater is situated behind the access panel on the outside of the vehicle, behind the cab. If you want additional information and some critical advice (so that you don’t harm your water heater), see our tutorial on how to turn on an electric water heater in an RV. Camper FAQs is made possible by donations from readers. It is possible that purchasing through links on our site will result in us receiving an affiliate commission. Because I am an Amazon Associate, I receive money when people make eligible purchases.

Leave a Reply

Your email address will not be published.