How To Get Water Off Pool Cover Without A Pump - ERNIEGRAVES

Tips on How to Drain Water from a Pool Cover

Does your pool cover have an overabundance of water on it? We’ve compiled a list of suggestions for properly draining water from a pool cover.

Draining Water from a Pool Cover with a Pool Pump

The first option for draining water off of your pool cover is to utilize a pool pump (sump pump) and a garden hose in conjunction with your pool cover. Disclaimer: Some of the links on this page are referral links, which means that if you make a purchase, there will be no additional cost to you, butRunning A Householdwill gain a fee on the transaction. Connect the garden hose to the pool pump in step one. Tip: Double-check that the hose is securely secured. If this is not done, the hose may pop off underwater, which may hinder or halt the draining process.

It appears to have sufficient power to complete the task at hand.

This pump is put to extensive usage.
Step 2: Decide where you want the water from the pool cover to drain into.
The next step is to submerge your pool pump in the water on top of your pool cover.
The majority of pool covers are constructed of a mesh material.
Step 4: Connect the pool pump to a grounded electrical outlet.
Most of them feature GFI outlets, which means that if any moisture is detected, the outlet will trip.
Step 5: Check to see that the pool water is draining properly.
A kink in your garden hose might cause your pump to overheat and burn out if the water is not draining properly or draining slowly enough.
If you are working on this project on a warm day in the winter or very early in the spring, it is likely that ice will form within your garden hose while you are working.

More information on the pool pump may be found at the following link: Little Giant 505005 5-MSP 1/6 HP Submersible Utility Pump, 1200 GPH, Little Giant 505005 5-MSP 1/6 HP Submersible Utility Pump, 1200 GPH, Little Giant 505005 5-MSP 1/6 HP Submersible Utility Pump, Little Giant 505005 5-MSP 1/6 HP Submersible Utility Pump, Little Giant 505005 5-MSP 1/6 HP Submersible Utility Pump, Little Giant 505005 5-MSP 1/6 HP Sub

Removing Water from a Pool Cover with a Garden Hose

In the case of an above-ground pool, it is feasible to drain the water using only a garden hose to save time. Here’s how it works:

Connect the hose to the faucet and place the other end of the hose on top of the pool cover to keep the water from leaking out. Inspect the object to ensure that it is submerged and that it will remain submerged
Activate the faucet and allow it to run for a minute
Turn off the water and remove the hose from the faucet as fast as possible. The water from your pool cover will begin to drain at this point.

We like to utilize hoses that do not kink, such as this one: A garden hose that will never kink has a number of advantages.

You will not be required to purchase a pool pump, which may range in price from $50 to $150. It’s easy and quick to do

Disadvantages

The hose in the pool may move about, forcing the draining process to come to a halt
You are restricted in the amount of water you can drain from your pool. Once you’ve disconnected the hose from the faucet, it might be difficult to move the hose. Simply prepare ahead of time and choose where you want the water to drain

What is an elephant cover?

Another approach for keeping water off of your pool cover is to prevent it from ever accumulating in the first place. An elephant cover can be used to remedy this problem. The elephant cover, on the other hand, is what? Surely, you’ve seen the advertisements. The pool cover extends over your in-ground pool, allowing the water (as well as fallen leaves) to drain to one side. The cover is so sturdy that it can support the weight of an elephant. They are also known as safety coverings in some circles.

Pool cover safety: If you have dogs and/or small children, this is an excellent technique to ensure that no one falls through your pool cover. Low upkeep: Because water and leaves are unable to gather on top of the cover, you may skip doing regular maintenance.

Disadvantages

Form: Drill holes into the surface surrounding the pool in order to put the cover, which will give it a more finished appearance. This necessitates the drilling of holes into concrete. We have pavers surrounding our pool, and we didn’t want to take the chance of drilling through them. We were also concerned about the possibility of having exposed holes when the cover was removed. Price: We have just checked the pricing again, and they are too high. In-ground pool covers for a typical 16 x 36 in-ground pool range from $700 to $1500. We were able to locate one for $1200 that came with a 12-year guarantee. A basic mesh cover costs between $90-200 and may endure for three to ten years. Fortunately, we were able to locate one for $199 that included a 16-year warranty.

The following is an example of a pool safety cover. To see a variety of sizes, pricing, advantages, and features, please visit the following link: Blue Wave Safety Cover for Above-Ground Pools As you can see, there are a variety of techniques available for draining water from a swimming pool cover. Have a great day swimming! Do you require any other pool advice? Please read the following articles on our website, which may be of assistance: Tips for Cleaning the Pool Cover of Leaves Checklist for Pool Cleaning Checklist for Pool Chemicals

Want to keep your home running smoothly?

Join our mailing list to receive PRIORITIES, our free weekly newsletter that includes:

Articles on time management, maintenance reminders and advice, free printable forms and checklists, and discount coupons are all available.

To sign up to receive PRIORITIES, pleaseClick here

16k times it has been asked and seen The winter has finally come to an end, and it’s time to take the cover off my above-ground swimming pool. Snow and rain, on the other hand, have left a significant amount of water on the cover. There are three possibilities available to me.

Remove the lid off the pool and allow the water to flow into it
Utilize a garden hose and make an attempt to siphon some of the water away
Purchase a pump and use it to drain the water

I’m not sure I want to just let the water run into the pool because the water on the cover is so disgusting. My understanding is that siphoning would be effective, but I am not confident in my ability to initiate the process or that the water would continue to flow after the process was initiated. I haven’t looked into purchasing a pump yet, so I can’t tell you how much they cost or how much electricity they require at this time. I’d also have to keep an eye on the pump to make sure it didn’t run out of fuel.

Are there any tried and true methods that pool owners rely on for their pool maintenance?
asked Posted on April 6, 2015 at 22:56 Testing101Testing1128k75 gold badges302 silver badges584 bronze badges1 Tester101Tester101128k75 gold badges302 silver badges584 bronze badges My family had a pool that would be protected from the elements during the winter.
The siphon would be initiated by inserting one end of the hose into the pool and filling the hose with water through the faucet on the other end.
This was accomplished by placing the hose’s end in a beach play bucket with a block inside, ensuring that it was constantly at the lowest position and so would not receive any air into it.
We would occasionally use the pool vacuum hose, but because it was so large (1 1/2″ OD), it was difficult to get a siphon to work properly.
This is especially important if you would otherwise be replenishing the pool with water that contains metals or other potentially harmful impurities.
If you are able to achieve that level, I would suggest that you suck it up (pun intended) and employ this choice.

Cheap ones are available for less than $50, making them a viable choice.

I’ve completed all three steps and now have a mesh cover that allows water to drain into the pool while the pool is in operation.

There are 22 silver badges, 45 bronze badges, and 1 gold badge.

This was something I had to perform several times a year on a regular basis.

Another time just before the pool is set to open.

Despite this, these pumps still leave a few gallons behind, which are frequently dumped into the pool.

I used a device that looked similar to the one below, which could also be connected to a water pipe. Approximately $60 from Harbor Freight tools: answered May 26, 2015 @ 22:05:05Off the clock It’s called the GoldOff. The Gold5531 gold badges, 8 silver badges, and 21 bronze badges are available.

Not the answer you’re looking for? Browse other questions taggedpoolpumporask your own question.

The possibility exists that you’ve recently weathered a major storm and would like to undertake some preventative maintenance to ensure that your pool cover lasts the duration of winter, or that you’re just getting your pool ready for the season. Regardless of the reason for doing so, all pool owners will be confronted with the unpleasant duty of removing the icky water that has collected on top of the cover at some point in their lives. It doesn’t matter whether you have an above-ground or an in-ground pool; if you cover it for the winter in order to prepare it for usage in the summer, it will undoubtedly gather water before it can be used again.

Even if you are fortunate enough to avoid having to remove some mid-winter water buildup, you will still be confronted with the task of ensuring that the water is properly removed in order to be able to open your pool when the weather changes.
When removing the cover, some people may delude themselves into believing that if they collect the cover exactly so when removing it, then all of the water will just glide off with the cover.
Despite appearances, an inch of water dispersed across the whole cover can condense and accumulate into a single massive mass that would be hard to carry and remove by hand.
As a result of attempting this, the dark brown water and decaying plant debris will often be spilled into the clear water remaining below, resulting in the things that was meant to be kept out of the pool now being mixed with the pool water that you were hoping to preserve.
It is critical to remove any water and debris from the area before removing the cover in order to achieve the best results.
In addition, you will not break your back or damage yourself to the point that you will need to visit the doctor once you have completed the workout.
We’ll go through these three steps in more detail below, and then we’ll recommend a better solution that will save you time and effort while also transforming this task from something you hate into something you don’t have to worry about at all.

Even while all of these approaches will eventually yield satisfactory results, they will each have their own set of downsides that may be avoided by approaching the task in a different way.

Electric Pump

However, while it is the most successful of the conventional procedures, it is also the most expensive of these treatments. There are pumps that are specifically built for this purpose that may be purchased, but they are not inexpensive, and they will not be used for any other purpose. When you use one, you must also consider the cost of power, as well as the need for an extension cable that is long enough or an outlet that is close enough to the machine. In essence, the pump will sit in the water for a period of time before beginning to pump out the water.

Even while it is not the quickest or most silent method, it will remove the most of the water from the cover.

Additionally, dirt, leaves, and other debris are frequent in the water that collects under your cover, and they are renowned for producing problems when the water is forced through a pump.

Set the pump at the bottom of the cover and turn it on to start pumping.

Bail With a Bucket

Although this approach is one of the most annoying, it is also one of the least practicable when dealing with larger pools or greater volumes of water. If you prop up one side of the cover that is far away from you, or sink down the side that is closest to you, then the majority of the water will accumulate within reach of you. After that, you may begin dipping the bucket into the water to draw up water and debris, and then tossing the bucket off the cover. Working in this manner will undoubtedly remove the water, but it will take a great deal of time and work, and you will be required to chase after the moisture in order to entirely remove it from the cover’s surface.

The fact that you will be dipping the bucket with your hand increases the likelihood that you will come into contact with the brown liquid that has developed as a result of the accumulation of water, which is not something that most people would like to do.

Siphon Hose

Because pumps are costly and buckets are inconvenient, the majority of individuals resort to siphoning the water from their pool’s lid. This is a rather effective strategy that will yield respectable results in a relatively short period of time, if followed correctly. The biggest disadvantage of this strategy is that it needs a certain amount of expertise in order to be effective. When you first turn on the siphon, you will have to suck on the hose and risk tasting the muck, or you will have to fill the hose exactly so and execute a precise movement and get the location just perfect in order for the siphon to begin working on its own.

The draw created by the force of gravity and pressure inside the hose will be sufficient to suck the water off the cover, through the hose, and out onto your yard, if done correctly.

If everything is “primed,” you’ll grab one end and swiftly swing it down towards the ground, being sure to maintain the other end submerged in water during the process.

Once the hose begins to sucking air, the water flow will be interrupted, and you may be left with a little amount of water that must be dealt with by using a different technique or resuming the siphon after gathering it in one location.

When opposed to utilizing a pump, it provides equal speed and efficiency, but you don’t have to worry about clogging as much. In most circumstances, you may begin to work right away with this approach, although when using an electric pump, you may need to brush out debris in order to avoid issues.

A Better Way

The usage of a Slide N Pump is one of the most effective ways to get rid of all of the water that has gathered. It’s a reasonably priced gadget that will provide the comfort and convenience of a pump while also providing the speed and simplicity of siphoning. It will provide you with a quick and simple means of eliminating water from your pool and preparing your pool cover for removal, and you will not have to handle the water, worry about clogging, or spend a lot of energy. The sucking action may be used to remove a little quantity of water rapidly in order to undertake mid-winter maintenance, or it can be used to remove a big volume of water when you remove the entire cover.

It will be equally effective on large and small pools, and it makes no difference whether the pool is in-ground or above-ground in nature.

If there was ever a tool made particularly for this function, it would look quite similar to this one.

Take advantage of this fantastic equipment to make opening your pool less difficult, and then have it on hand to save time and money when performing other tasks as well.

How Does It Work?

The tool’s operation is rather straightforward. It operates by the use of a pump-like action, and it will function as a standard pump, sucking in water with each hand stroke, or as a siphon, continuing water flow after a single movement.

To make use of this gadget, you will need to attach a hose to either side of it. One will be placed in the water on the cover, and the other will be placed outside in your yard to direct the water where you want it. The water flow will be initiated by a simple pump operation, and it will continue in the same manner as a typical siphon.

The difference is that you never had to touch the water, suck on the hose, or do any other particular actions or procedures in order to get the water to start flowing. The fool-proof operation eliminates the need for trial and error, and assures that you will be able to get the siphon started no matter what amount of competence you possess. Similarly, as long as plant matter and other muck are tiny enough to pass through the hose, they will not clog up the system or cause difficulties while you are working.

At some time, the siphon will come to a complete halt, and the water will cease to flow.
It is possible to remove more water with less effort when you use this equipment, and you will complete the work with ease.
Then you’ve come to the right place.
By utilizing this fantastic gadget, anyone working with any pool may quickly achieve excellent results and complete the task without a single complaint.

Pump and slide your way through life. Mini Slide N Pump– The same wonderful concept in a more compact package.

Step By Step Instructions: Siphoning a pool cover with the Slide N Pump.

Before you begin, you’ll need to gather your materials and tools. It should be obvious from the title that a Slide N Pump is required to complete the task according to these instructions, but you will also want two pieces of hose. In this particular instance, we utilized a conventional garden hose for the rear side of the tool and a shorter hose leftover for the front side of the tool. Although a regular-sized pump was used in this instance, the mini-sized pump may also be used to complete the work.

Whenever this occurs, you may manually pump the leftover liquid out of the cover, and the larger-capacity pump will allow you to do so much more quickly.

Step 2. Place the Hose

The longer hose is the one that is used to fill the huge puddle that forms on top of your pool’s protective cover. When putting it in, make sure to place the end so that it sits towards the middle, but also make sure to keep it away from any debris that might create issues later in the process. If you have a large amount of standing water, like we had in this case, you may expedite the process by lowering the entire hose (or at least the majority of it) so that it fills with water more quickly.

Step 3. Direct The Water

A 50-foot garden hose was used, and when we were through, half of it was sitting on the cover, partially submerged in water, and the other half was dangling over the side. If you look closely, you will note that it is directed down over the side of the house and out into the yard. You may direct the water in whatever direction you choose, and you can even use a longer hose if you want to, but you must make sure that the exit point is lower than the water you are attempting to remove. Water does not flow uphill on its own, and if the pressure inside the hose is not maintained, the water will cease to flow completely.

If the exit end of the hose is level with, or somewhat higher than, the height of the pool cover, you will never be able to get a siphon to commence and will wind up working more harder than necessary.

Step 4. Connect The Pump

The Slide N Pump must be connected to the hose once it has been placed on your lawn or in another spot where you want the water to end up after it has been placed. Prior to connecting this longer portion of hose to the tool, we attached a shorter section of hose (about 2-3 feet) to the front of the tool. When determining the length and position of the hose that will be necessary in your situation, bear in mind that after the siphon is up and running, you’ll want to remove the pump, thus the only real purpose for a hose on the front end is to keep the initial flow away from your body.

Once the water begins to flow, the majority of it will escape through the longer hose since it will continue to flow out automatically until the siphon is turned off by the user.

Step 5. Pump It Up

It’s time to get things going now that you have a hose connected to either end. To get the water to flow through the hose and off of your pool cover, just take out the hose and then put it back in to begin pumping water. In this particular scenario, it only needed two full pumps to initiate the siphoning process. The fact that water will come out of the front hose without you having to do anything indicates that it has been started. If everything is set up correctly, it should only require a minimal amount of pumping; however, if you find yourself working too hard or becoming frustrated at this point, you may want to go back and review the preceding stages.

Step 6. Remove The Hose

The moment you detect that the liquid is starting to flow on its own, turn off the pump and put it somewhere safe to rest. Most of the time, you won’t need it again, but it’s good to have it on hand just in case.

Step 7. Inspect The Flow

Following the removal of the pump, keep an eye on the end of the hose for a short period of time to ensure that the water continues to flow. If this is the case, you should be fine to proceed. A screen is used to keep debris out of the pump, which helps to maintain good operation and long-term viability. Because of the nature of the task, clogging the drain with leaves and several other types of muddy, goopy sludge is a distinct possibility. Therefore, it is critical to situate the hose end away from decaying plant waste and to turn off the pump immediately after it starts siphoning.

If it is clogged, simply clear it out and try it again later.

Step 8. Let It Go

As soon as the siphon is activated and the water is being channeled away from the cover and into the yard, you can simply leave it alone. The length of time necessary to thoroughly drain it will vary depending on the scenario, which is why we completed this task in the evening. It was left overnight, and when we returned the next day, the water had evaporated, and we were one step closer to being able to remove the lid completely. With the amount of water that had accumulated in this situation, it would have taken a long time to watch it drain completely; thus, if you have a comparable amount of water, the most convenient thing to do is to let it drain while you are sleeping.

Step 9. Check It Out

Regardless of whether you wait overnight or just an hour or two, after the siphon stops, the majority of the water should have been removed from the system. It is possible to manually remove a little amount of liquid if there is a tiny amount of liquid remaining after reconnecting the pump. In this particular instance, we were able to remove a substantial amount of water from the surface of the water using the siphon alone, so we proceeded on to the next phase, which was eliminating whatever that brown clump of stinking things was.

When it comes to low spots or huge areas of water that have accumulated, utilizing the instrument as a manual pump should allow you to get rid of them in a matter of seconds.

Before and After

The significant results can be seen in the photo above, which was achieved with little work on our part. The whole set-up time was maybe 5 or 10 minutes, and after that, it very much took care of itself, according to the client. One disadvantage is the length of time it may take for the water to drain out of the garden hose, but if everything is arranged properly, you should not have any issues with the water. We were able to turn a potentially devastating issue into a manageable chore as a result of this useful technology.

How Do You Remove Rain Water Off Your Pool Cover?

It is advised that your swimming pool is covered during the off season when it is no longer essential to add chemicals or keep your pool pump operating owing to the cold winter weather. If you’re not sure when the ideal time is to close and cover your swimming pool, check out “Best time to close your pool,” a piece in which I explain when you should close and cover your swimming pool for the year. When you cover your swimming pool, it is possible that you may have some rain, sleet, or snow from time to time, which will accumulate on top of your pool cover.

So, what is the best way to get the water out of your swimming pool cover?

Instead of using a nearby faucet to entirely fill the hose, you may prime it by detaching the hose and placing it on a downward slope once it has been completely filled with water from the adjacent faucet.

Removing Water Using A Submersible Pump

I have a Thermoplastic submersible pump with a horsepower of 1/3 that works flawlessly for eliminating water from the top of the pool cover during the whole winter season. Draining the water as needed is simple, quick, and requires no priming, luck, or talent on your part.

Using a regular water pipe, connect the submersible pump of your choosing to the faucet. Some pumps may require an adapter to be attached to the pump’s output drain in order for a standard water line to be able to function correctly. If this adapter is necessary, it will be provided with the majority of new pumps. Install the pump in the water according to the manufacturer’s instructions. Before you put the pump in the water, ensure sure it is built to be totally immersed beneath the surface of the water
Otherwise, the pump may fail. Take out any kinks and cramps in the linked water hose and lay it on a downward surface so that any remaining water may drain
The pump will begin to suck the water off the pool cover and out of the water hose as soon as it is plugged into a power outlet (ideally an outdoor outlet if one is available). If an extension cord is necessary, consult the pump handbook from the manufacturer to establish the correct extension cord requirements. When the pump first starts pumping water, it may take a few minutes until all of the air has been evacuated from the pumping system.

Are Submersible Pumps Safe?

As we all know, water and electricity do not mix and can result in an electrical shock if they are used in conjunction. With this being the case, how can submersible pumps be considered safe to operate when the entire pump will be submerged in water? Water pumps of this sort are particularly built to be submerged in water without the risk of electrical shock, which is why they are so popular. Before using any equipment, make sure to read the owner’s handbook and any cautions. The danger of shock may be there if the pump is not operated appropriately or if the pump fails in some way.

The motor of the pump is contained within a watertight housing unit. This prevents water from seeping into regions where it might cause damage to the pump or electrocution, among other things. Long insulated power lines are connected and sealed with waterproof neoprene to ensure that water does not come into touch with any of the electrical wires within the machine. The area where the wires meet the motor casing is sealed with epoxy, which totally seals off the area from water. This prevents water damage from occurring, which might result in pump failure, and it also indicates danger.

These pumps are particularly built to be submerged in water, with some models being able to be submerged up to a depth of more than 10 feet, depending on the type. All precautions are taken to ensure that they will work in a safe and efficient manner while carrying out the task for which they were created.

Siphon Water Manually Only Using The Water Hose.

No issue if there is no pump! Watch this 60-second video to discover how to siphon water from a hose with only a few simple tools. If you do not want to spend the money on a submersible pump, you may siphon the water from the pool cover using your water hose and water faucet if you have one.

To begin draining water from your swimming pool, first ensure that you have a water hose that is long enough to reach your water faucet. Then, simply follow the few simple steps outlined below to begin the process.

Water hose connected to the water faucet spigot should be tightened. Examine the water hose line for any bends, crooks, or cramps, and then lay one end of it on top of the pool cover
Placing the water hose’s end entirely beneath the water will ensure that no air will enter the water hose. Installing a boulder or block between the water hose and the wall will help to ensure that the hose remains completely submerged at all times. Water should be pumped onto the pool cover by turning on the water faucet. This is done in order to thoroughly fill the hose with water and remove any air from the line. It is impossible for water to flow correctly if there is air in the pipe. Keep an eye out for air bubbles as the water flows into the pool via the cover. The water should be turned off after there are no air bubbles visible and the water is flowing smoothly. Carefully disconnect and lay down the water hose in a position where it is lower than the pool cover, so that water will begin to drain away from the pool cover. If the water is not draining, check to see if there are any kinks in the water hose or if there is any air lingering in the water line
These processes do take some practice and may need to be done a few times before a good flow of water is being drained is obtained. The method may need to be repeated if the water does not cease flowing.

Importance of Keeping Water Off Your Swimming Pool Cover — Aqua Pools Online

Water should not be allowed to accumulate on your swimming pool cover. The Advantages of Using a Pool Cover Many homeowners choose to cover their swimming pool with a pool cover, especially during the winter months when temperatures are lower. Simply put, while your pool is not in use, it is protected by a pool cover that is attached to it. It keeps debris out of the pool, which reduces the amount of time spent maintaining it. Your time spent skimming your pool to remove undesired impurities will be reduced, allowing you to spend more time swimming and relaxing in it.

As a result, you will not have to refill the water and chemicals as frequently.
But, perhaps most crucially, a correctly placed pool cover ensures that children do not drown.
Due to the extra water in the pool, the water in the pool may be moved, creating a drowning hazard for children.
It is critical to remove this extra water in order to keep your cover in good condition and keep your family safe.
Taking Water Out of Your Pool Cover (Part 1) The cover pump operates by moving water away from the pool cover and into the pool.
The majority of cover pumps are electric, which means they must be plugged in to be used.
In spite of the fact that it is a very affordable and lightweight piece of equipment, it is well worth the investment.

manual transmission Manual and automated pool cover pumps are the two most common types of pool cover pumps.

Some manual pumps do not have an electric motor and must be controlled manually.

Pool coverings are most frequently used by homeowners during the chilly winter months when the weather is frigid.

Even if the pool is covered for the winter, water will inevitably accumulate on the cover.

Pumps that operate automatically can be left on the cover.

Make careful to remove the water while it is still in liquid form after the freeze has gone.

Pool Cover Pump Repair and Upkeep Your pool cover pump is low-maintenance and requires little to no attention.

Regularly inspect the screen of your pump and clear it of any debris that may have been lodged in the screen.

Remember, though, to bring your cover pump and hose indoors if the weather is below zero degrees.

However, keeping excess water off of your pool cover is an important step that should not be overlooked. The addition of a pool cover pump will take care of this important stage in pool maintenance.

Here’s Why You Need to Keep Water Off Your Pool Cover

A pool cover is an excellent investment since it protects your pool from debris in both the winter and the summer, as well as from children or dogs accidentally falling into the water. On the other hand, one of the most significant drawbacks of pool covers is that they have a tendency to accumulate water and debris over time. Particularly during the winter months, large amounts of snow or rainfall might be dumped upon your pool cover, which can be difficult to remove. Pool supplies in New Haven County, CT, on the other hand, may be rather expensive, which means you’ll want to take as many steps as possible to ensure that they remain in excellent condition.

Pool coverings can be damaged if they accumulate a lot of water.
This is due to the fact that pool covers are not designed to handle the weight of water (or anything else) being placed on top of them.
This pressure can produce tears in your pool cover, and in some cases, the cover may even fall into the pool completely.
Additionally, you must consider what will happen to all of the stagnant water if you do decide to keep it on the cover for an extended period of time—especially during the winter.
And if you don’t pump the dirty water out of the snowbank when it melts and it’s time to remove the cover, all of the nasty water will be thrown directly into your pool.
If it has rained recently, you should remove any standing water as quickly as you can.
One of the most important pool supplies in New Haven County, CT, is an automated pool cover pump.
Only once in a while should you inspect the pump to ensure that it is still operating correctly and that it is not blocked with debris.
It is still necessary to remove it since it can become quite heavy very rapidly.
Push the snow away from the cover with a roof rake or other similar equipment.
If there is ice on the pool surface, you must allow it to thaw before pumping the water out of the pool.

If you don’t already have a pool cover to keep your new pool protected, stop by A-1 PoolsSpas! To fulfill your needs, we sell a broad variety of pool supplies in New Haven County, CT, ranging from pool covers and pumps to pool toys and chemical additives. Uncategorized is where you’ll find it.

How to get Water off Pool Cover + Prevention Tips

Pool covers are an important element of the pool cleaning process, and they also serve as a safety barrier to prevent accidental drownings in swimming pools. However, getting water off of a pool cover can be difficult, especially if there is a considerable volume of water on the cover at the same time. Due to the numerous options available, excess water from your cover may be removed using a variety of techniques, such as by emptying it into a bucket or utilizing electric pumps to remove it, siphoning it, or using an electric pump.

Pressure washing will often take less than 30 minutes to complete the job correctly.

The following are the specifics.

Siphoning the water from the pool cover

In order to remove water from a pool cover, the first step is to use an ordinary hose to siphon the water out of the pool cover. This approach will necessitate you having access to the edge of the pool cover as well as a pipe that is long enough to reach the top of the cover and be connected to an emptying place on the other end of the pipe. These are the measures to take in order to siphon the water from the pool cover:

Debris should be removed manually from any large areas such as branches, leaves, or any other object
A high-density item such as a stone or metal should be attached to one end of the rope. The item attached to the hose pipe assists in forcing the hose pipe to reach the bottom of the water. Make certain that the object attached does not obstruct the hose pipe. Connect it to a water source and turn it on. The goal is to completely fill the pipe with water in order to remove any air that might interfere with the continuous flow of water. While the water from the faucet is still in the hose, drop the end of the hose with the attached object into the water on top of the pool cover. Placing the other end in a dry spot away from any standing water is recommended. Water must flow through the hose if it is installed with one end on the pool higher than the other end. Once the water begins to flow out of the pool cover, lower the water level to a safe level until the water has completely flown out.

Make sure the end of the pool cover is completely submerged at all times to avoid drawing in any air, which might cause the siphoning process to halt. Advantages The following are some of the advantages of this method:

Because all that is required is a hose, it is both easy and economical. It can discharge the water from the cover in a matter of minutes
It is also lightweight. There are no tools necessary because the pool cover can be pushed up a small amount to provide access to it. Those who rent their homes will find this strategy to be particularly advantageous since they will not have to worry about destroying any portion of the property. There are no hazards involved because you do not have to climb anything or use any type of energy with this approach.

Disadvantages The following are some of the downsides of this method:

Leaving the hose end on the pool cover on its own might cause the end to slide about and enable air to enter the pipeline. The siphoning process will be halted as a result of this. It is not feasible if you need to transfer a large amount of water since it will take longer than other methods and may necessitate more time, effort, or a combination of both
It does not remove a significant amount of dirt from the cover.

In the event that you don’t have any tools to work with, this is the greatest option.

Using a bucket

Another simple technique is to remove the water from the pool cover by using a bucket. Using this procedure, you can easily clean tiny amounts of water from small pools with robust pool covers, and it is pretty simple to perform without the use of any special equipment or instruments. It will be necessary to use a bucket in order to remove all of the extra water that has accumulated on top of the covers by scooping the water out in repeated motions. removing surplus water from the pool cover The bucket’s aperture should be large enough to allow for easy pouring but not so large that it causes spilling while being moved from one location to another, as described above.

This technique has no complicated procedure because it does not necessitate the use of any instruments of any type, and it should only take a short length of time for modest amounts of water to be completed.

Providing there is enough area to work, this approach will be successful at removing any surplus water without creating a lot of mess, since nothing other than the bucket has to become wet by coming into touch with stagnant pools above pool covers to be effective.

Using an electric pump to Drain pool cover

Another option for doing this work is to make use of a portable electric pump. To use this approach, you will need a hose that can be introduced into the water in order for it to be sucked from one location and transferred to another one, much like the previous ways. When compared to gravity or siphoning, which rely on pressure differences between two places, electricity does all of the work for you by driving water from one end to the other. This is the most significant distinction. The following are the procedures to be followed for this option: 1Skim the top of the pool cover with a broom.

When you begin the cleaning procedure, this will help to keep the pump from becoming clogged.
After that, you’ll need to attach a hose to the pool cover and plunge it into the water, as well as connect the other end of the hose to your electric pump, which will be the next step.
Before turning on the pump, make sure that any broken components have been repaired.
Electric pumps are available in a variety of configurations; some come with a pipe that is simply inserted into the water, while others come with a suction hose that is inserted into the water instead.
Position the emptying end at a collecting location to complete the cycle.
5Connect the electricity and turn on the pump to test it.
In turn, turn on the pump and let it run until all of the water from the pool cover has been pumped away.
6 After the water has been removed from your pool cover, clean it up.
You may clean the cover either while it is still on the pool or when it is removed off the pool.
To cut away parts of surplus material that have folded along one edge (typically at corners), use scissors or shears to cut out the sections.

Using a Slide N Pump

If you want to remove water from the pool cover, you may also use a Slide N Pump. Via an entrance on one end and a suction tube on the other end, a Slide N Pump is a gadget that is attached to the contour of your pool with brackets. The Slide N Pump gadget operates in a manner similar to a hybrid of the electric pump and the hose approach. It has the appearance of a standard hand pump and operates by pumping water from the pool cover into the pipes in order to remove the air. Afterwards, the water will flow on its own to the spot that you specify.

You can accomplish this by following the procedures outlined below: 1Set up the work environment Prepare two sections of hose for this activity by cutting them in half.
This section should be kept to a minimum since it will link to the water on the pool cover and then to the Slide N Pump.
2 Attach the pump and hoses together.
Place the shorter end of the hose into the water on the pool cover and the longer end at the area where you want the water to be emptied.
Simply give the gadget a few pumps, and it will force the water into the pipes without any more effort.
If there is still more water on the pool cover than can be taken away, keep running the pump until the water is fully removed.

4Take out the pipes. Following the completion of these processes, your pool cover should be ready for use. Simply remove the pipes and Slide N Pump mechanism from the pool, clean the cover, and then enjoy the pool.

How to prevent water from collecting on a pool cover

Using an elephant cover on a pool cover will help to prevent water from gathering on the cover. This pool cover, as its name implies, is sturdy enough to bear the weight of an elephant in the water underneath it. Blue Wave provides a strong pool cover. As a result, the weight of the water will not be sufficient to cause it to droop inwards, as it does with other pool coverings. Elephant pool covers provide a number of advantages. The elephant pool cover offers a number of advantages, some of which are as follows:

The weight of the water will not be sufficient to cause it to droop inwards, as is the case with conventional pool coverings. This means that the pool cover will have a longer lifespan since the material will not be stressed as much by the weight of water droplets, dirt, and debris on it. As a result, you’ll receive more value for your money from this sort of pool cover because it lasts longer than other types. They’re also low-maintenance pool covers since they don’t collect water droplets, dirt, or debris, which means they require less upkeep. Additionally, the elephant pool cover prevents dangerous ultraviolet rays from entering down into your swimming area, resulting in a safe atmosphere for swimmers who like taking time off from work to cool down in their neighborhood pool. The final point may not be as significant as the others, but it is still worth mentioning: Due to the fact that this style of cover is available in a variety of hues like blue, black, and green
Elephant pool covers are also a visually beautiful alternative.

Disadvantages Elephant pool covers, on the other hand, are more expensive than other types of covers, and the cost of installation is also more expensive.

Elephant pool coverings are expensive, and the installation of these covers is time-consuming and expensive. An elephant blanket can cost anywhere from $200 and $800, depending on its size. The cost of installing a panel is around $80 per meter, including labor expenses. The use of heavy duty anchors ($150 or more per anchor) with concrete set at least 50cm deep into the ground is advised
However, this type of installation is complex and makes it more difficult to remove the pool for maintenance.

Even so, elephant pool covers are among the most effective solutions for keeping water off your pool cover and into your pool.

A-1 Pools

The removal of excess water from solid tarp style winter coverings, which are typically used on above-ground pools and certain in-ground pools, is critical to preventing water damage to both the cover and the pool. A submersible pump mounted on your pool cover may easily accomplish this if the temperature is above freezing and liquid water is available in the water pool. This is most common in the fall before cold temperatures arrive, throughout the winter when unexpectedly mild temperatures persist for many days in a row, and in the spring when temperatures begin to increase as the weather warms up.

Unless the water in your pool is frozen, when water accumulates on the pool cover, the weight of the water on the cover displaces water from inside your pool, which exits through the return hole and/or skimmer.

Consider the fact that the water in a 24′ round pool weighs approximately one ton every inch of its depth.

As the load from the weight of the water on your cover grows, your cover will initially begin to strain.

If your pool cover drags the steel wire up against the top ledge of your pool, the top ledge may be fractured or even torn away from the pool wall entirely.

Water bags or other weights are used to anchor a tarp type cover to your in-ground pool, which keeps the cover in place on your pool deck.

Placing a submersible pump on top of the pool cover, preferably on a solid object such as a Frisbee, can prevent water from being sucked through the cover and will remove surplus water when the temperatures are warm enough.

Drain the water from your cover as soon as possible in the spring to give any residual water a chance to dry off.

Afterwards, after the pool is completely filled, you can effortlessly float your cover away from the pool, making cover removal simple while also avoiding debris from falling into the pool. If you have any issues or need special instructions, contact your pool pros at A-1 Pools!