ERNIEGRAVES | Process Measurement & Control

What Would Cause Hot Water Heater Breaker To Trip?

Posted on Author Andrey KiligannPosted in CONTROLOTRONLeave a Reply

Problems With an Electric Hot Water Heater That Trips a Breaker

The fact that your hot water heater is tripping a circuit breaker on a regular basis indicates the presence of a potentially dangerous condition that must be addressed immediately in your house.A simple re-activation of the circuit breaker will not resolve this issue.A trained specialist should be called in to do the repairs since water and electricity may be quite dangerous when combined.

Breaker Breaker

The presence of a hot water heater on an electrical circuit might result in the trip of the breaker for three reasons: water leaking on the electrical wires, a problem with the unit’s thermostat, or an issue with the breaker.The most typical reason for this is a dysfunctional thermostat.In this scenario, it is necessary to replace the thermostat.The replacement of the heating element may be advantageous in this situation.

  • A leak that allows water to get into touch with any of the electric components is harmful and can cause the circuit breaker to trip and cause the breaker to trip.
  • A leak produced by a failed gasket must be fixed, but the device must always be treated as though power is still flowing and a specialist should be contacted.
  • In certain cases, a malfunctioning circuit breaker is the root cause, and the old circuit breaker should be replaced with a new one of the same size to prevent further damage.

Why a Water Heater Keeps Tripping the Breaker

Electric water heaters are connected to a separate circuit.This indicates that their circuit breakers are not connected to anything else.It is possible that the breakers will trip for no apparent cause at times.They can trip at any time and then be reset, allowing you to continue using the water heater for a period of time until it trips again.

  • You might be unable to reset them if they trip in another situation.
  • It is for a reason when circuit breakers trip, and it is possible that this is a dangerous scenario that requires rapid care.
  • No matter how infrequent their trips are, they are nonetheless being affected by something.
  • It is vital to fix the problem as soon as possible in order to prevent causing damage to your property or risking an electrical fire.
  • In this post, we’ll look at what causes the water heater breaker to constantly tripping and what you can do to prevent it from happening in the first place.

What Should You Do?

First and foremost, if the breaker keeps tripping, do not keep flicking it back on and on.If you do this, you run the risk of the wire overheating and igniting an electrical fire, which is dangerous.This can also shorten the life of your circuit breaker and cause severe harm to your water heater.The breaker is tripping as a result of a problem, and that problem is not going away on its own timetable.

  • Turn off the breaker and begin troubleshooting the problem as soon as possible.
  • Unfortunately, troubleshooting a tripped water heater breaker isn’t as complicated as it appears.
  • Following a few troubleshooting methods might assist you in locating the source of the problem.
  • The following are the most typical reasons and solutions.

Bad Thermostat

Water heaters are equipped with a limit switch that prevents the temperature of the water from surpassing 180°.It trips the limit switch (a little red reset button on the water heater) when the water temperature exceeds 180°F.This helps to save you from being burned or scalded by the very hot water flowing through the shower.The most common reason for the limit switch to trigger is a malfunctioning thermostat.

  • Each element has its own thermostat, which means that a two-element water heater has two thermostats.
  • To guarantee that only one element is being heated at a time, the thermostats communicate with one another.
  • When they break down, they might become trapped in the on position for a while.
  • Consequently, either one or both heating elements will remain on and continue to heat the water as a result of this action.
  • If the water heater contains two elements, as most electric water heaters do, the circuit might be overloaded if both elements are left on at the same time, which is dangerous.
  • The circuit will then draw an excessive amount of current and get overheated, resulting in the trip of the breaker in the breaker box.
  • A multimeter may be used to check the thermostats’ performance.
  • Check to see that the water heater’s electricity has been turned off.
  • The thermostat should be checked for resistance once the wires have been disconnected (mark the wires so you remember where they join).
  1. The resistance should be zero ohms (it should show an open, or infinity) for a normally open (NO) thermostat, and it should be close to 0 ohms (it should have continuity, but it could have as much as 0.5 ohms including the meter and leads) for a normally closed (NC) thermostat.
  2. Normally open (NO) thermostats should have no resistance.
  3. Thermostats that are not working properly will need to be replaced.
  4. The replacement of the heating elements at the same time as the replacement of the thermostats is highly recommended.

Bad Heating Element

  • In addition to the top and lower heating components that we’ve described, most electric water heaters feature additional heating elements. They collaborate in order to keep the water hot. If you have a large tank, this is extremely crucial. Typically, when a heating element breaks, the water ceases to heat and becomes significantly colder than typical. It is possible that the internal heating element is open, in which case the heating element will not do any damage. The truth is, however, that is not always the case. It is possible for the casing around the heating element to crack. When the electrical component of the element comes into contact with the water in the tank, it shorts the circuit and trips the limit switch or circuit breaker, as shown in the illustration. An element might be too short as well. As a result, the element continues to operate, continually heating the water in the tank. When the water gets too hot, this will cause the limit switch to trip. A multimeter may be used to test the performance of a heating element. Remove the wires from the water heater element while the circuit breaker for the water heater is turned off. Check for continuity across the locations where the wires connect to the element. You should obtain the following resistances: A 3,500-watt element has a resistance of 16 ohms
  • a 4,500-watt element has a resistance of between 12 and 13 ohms
  • and a 5,500-watt element has a resistance of between 10 and 11 ohms.

If you notice a difference in resistance, it is necessary to replace the heating element in question.

Water Leak

Water from a leaky water heater, for example, due to the failure of a gasket around the heating element, has the potential to come into contact with electrical components and cause the breaker to trip.This is extremely risky and has the potential to produce a catastrophic electrical shock.If the breaker hasn’t already been tripped, turn it off immediately and fix the water leak as soon as possible.

Internal Wiring

If the breaker trips, it is possible that an issue with the internal wiring is causing it.Open the panel while the power is turned off to check where the water heater is connected to the rest of the house’s wiring.Look for burned connections, broken wiring, or any other signs of electricity having arced in the vicinity.If there has been an electrical arc, you will most likely smell smoke.

  • Before operating the water heater, check for and replace any broken wiring and connectors.

Wiring or Electrical Problem

If the problem isn’t with the thermostat, heating element, a water leak, or internal wiring, it’s likely that the issue is with something else outside of the water heater itself.It might be caused by a faulty or frayed cable, a faulty connection in the electrical panel, or a faulty or worn-out circuit breaker.Check the wiring on the line to see if any wires are damaged or coming loose.It is necessary to replace the breaker if the breaker trips despite the fact that there are no issues on the line.

  • If the breaker is the source of the problem, make certain you replace it with one of the same grade.
  • Don’t replace it with a higher-rated breaker since doing so would enable more current to pass through the circuit, resulting in the circuit being too hot to handle.

Conclusion

When a water heater continues tripping the breaker, it’s not a pleasant experience.It can also be harmful and result in significant injury or property damage to you or your property.Fortunately, tracing down the source of the problem isn’t that difficult.Typically, a malfunctioning thermostat and heating element are to blame, but it’s also possible that a faulty circuit breaker or other wiring difficulties are to blame.

  • Keep in mind that safety comes first.
  • When dealing on electrical issues, always remember to use caution.
  • If you are not familiar with electrical wires, you should avoid working with them.

Why Is My Water Heater Tripping My Circuit Breaker?

Skip to the main content What is causing my water heater to trip my circuit breaker?Have you ever had something like this happen to you?The circuit breaker in your home is tripped by your water heater tripping.As a result, you go and reset the circuit breaker breaker.

  • A few minutes later, the same thing occurs once more.
  • As a result, you reset it once more.
  • The water heater, on the other hand, quickly trips your circuit breaker once more.
  • This recurrent pattern may be suggestive of a more significant problem that you are not currently aware of or aware of.
  • But, suffice it to say, you’re in desperate need of a water heater repair, or possibly a whole new water heater.
  • It is possible for a water heater to trip a circuit breaker for a variety of reasons, which we will go over in detail below to assist you figure out what you can do to resolve the situation.

Thermostat Issues

The failure of your water heater thermostat or inappropriate installation of the thermostat can result in the loss of ‘communication’ with the circuit breaker, which can result in an electrical imbalance of power.However, rather of controlling the flow of power to the heating components, this imbalance of surplus electricity is sent directly into the circuit breaker.A circuit can trip if it is subjected to high power because the circuit is unable to withstand the load.

Burnt Heating Elements

The element in the heater that warms the water might sometimes be the root of the problem.Because of this, if the heating element fails or burns out, it may cause sections of the heater to spit, exposing wires and electrical components to direct contact with water, resulting in serious injury or death.And we all know that water combined with electricity is a dangerous combination.As a result, it may produce a short circuit, resulting in your water heater tripping your circuit breaker..

  • In any case, you’ll notice that your water isn’t as hot as it used to be if your heating element isn’t working properly.

Faulty Breaker or Wiring

It’s possible that the problem is not related to your water heater at all. It’s possible that your circuit breaker has become worn and malfunctioning as a result of aging. Alternatively, a loose wire in the electrical panel might be causing the system to short circuit, leading it to fail. In either situation, it is the breaker that is causing the problem, not the water heater itself.

What Can You Do?

The first and most crucial thing to know is that you should not keep switching the breaker back on after it has shorted out again.The danger of overheating the wiring and sparking a fire is substantially greater than the chance of having a defective water heater if you do this repeatedly is extremely high.In the event that you’re considering installing your own updated breakers, be sure to talk with an experienced specialist first.However, even if the problem is not with the circuit breaker and an imbalance of energy is still passing through your system, you run the danger of scorching wires and risking a fire.

  • Higher-rated circuit breakers are thus recommended.
  • If you’re certain that the problem is with your water heater’s thermostat, you may purchase and install a new water heater thermostat in your house on your own initiative.
  • Just be sure to speak with an expert to ensure that it is done correctly, or better yet, have a professional come in and install it for you!
  • The best course of action is always to get the assistance of a professional to manage the matter for you.
  • A technician has been trained to search for these sorts of problems and can identify them without causing more harm to your breaker or water heater.
  • And don’t forget about your friends at Simpson Plumbing if you’re ever in need of a competent water heater professional in Tracy, Mountain House, or Manteca.

Share This Story, Choose Your Platform!

Page load link

Why Is My Electric Water Heater Tripping My Circuit Breaker?

  • Imagine this scenario: You find that your electric water heater has tripped the circuit breaker on its own. In order to correct this, you went to your electrical panel and reset the breakers. However, a little time later, your water heater’s circuit breaker tripped yet another time. So, what is causing this to occur? The following are the most likely causes: a burned out heating element
  • a faulty thermostat
  • a wiring or electrical problem.
  • The following points must be addressed first, before we go into the specifics of those issues: It is not necessary to continuously turning the breaker back on. In addition, this can cause the wires in the circuit to overheat (which might result in a fire), wear out the circuit breaker (which could result in it not tripping later), and severe damage to your water heater.
  • Replace the breaker with a higher-rated breaker if the current breaker fails. Increasing the size of the breaker without also increasing the size of the wire and other components of the circuit is essentially the same as removing the breaker’s safety feature. Now that the breaker has been reset, extra energy will be allowed to flow into the circuit, potentially causing overheating of the wires and a fire.

Let’s get this out of the way and move on to the probable issues that might be causing your electric water heater to trip the circuit breaker.

Burnt out heating element

Heating element: The heating element is the component of your water heater that actually heats the water.Typically, two heating elements are used in electric water heaters: a top heating element and a bottom heating element.An electric water heater with two heating components is depicted in the diagram.Photo courtesy of the author.

  • It is most common that when the heating elements fail, they just burn away, and the only thing that you will notice is that the water isn’t heating up to the same temperature as it used to be.
  • However, the heating element shell can sometimes fracture, allowing the electrical components to be exposed straight to the water or tank below.
  • This short circuit has the potential to cause your water heater’s high limit switch to flip and/or the water heater’s circuit breaker to trip.
See also:  How Often Should You Replace Fridge Water Filter?

Bad thermostat

In your water heater, the heating element is the component that heats the water.Typically, two heating elements are used in electric water heaters: one on top and one at the bottom.Electric water heater with two heating components as seen in the diagram.Obtaining a photo It is most common that when the heating elements fail, they just burn away, and the only thing that you will notice is that the water isn’t heating up to the same temperature as it used to.

  • On occasion, however, the heating element shell may crack and allow the electrical components to come into direct contact with the water or the tank.
  • Your water heater’s high limit switch may be tripped as a result of this short circuit, and the water heater’s circuit breaker may trip as well.

Bad breaker or electrical wiring

  • It’s possible that the problem isn’t with the water heater at all. For example, it is possible that the breaker itself is worn out and tripping unnecessarily
  • It is believed that a loose wire in the electrical panel is the cause of the short circuit.

If your water heater has been inspected by a plumber and everything appears to be in working order, you should have an electrician examine the electrical connections.

Get help from a plumber in Phoenix

If you reside in the Phoenix area, George Brazil Plumbing and Electrical will assist you with the repair of your electric water heater. Get in touch with us right now.

Related articles:

  • What is causing my circuit breaker to trip so frequently?
  • What is the source of the burning smell emanating from my circuit breaker box?
  • An Introduction to Electrical Panels, Part I: A Homeowner’s Guide to Breaker Boxes

Why Does Your Water Heater Keep Tripping the Breaker?

Have you been having trouble with cold showers lately?You won’t be able to resolve the problem with your water heating system unless you figure out why your water heater is constantly tripping the circuit breaker.Examine the water heater, the circuit breaker, and even the cabling that runs between them.You will, however, need to dig a little deeper into the matter and figure out what activities need to be taken to rectify it.

  • Just a friendly reminder that if you are not an expert in electrical repair, a simple problem-check will suffice; do not attempt to remedy the problem yourself.

What’s Really at Fault

So, what exactly is the source of the problem?You must be aware of the many circumstances that your heating system may confront.Because your breaker is constantly tripping, you should include all electrical components that are involved in powering up the tank in your calculations.The specific circuit breaker for your heating device, the cabling that connects the circuit breaker and the heater, and the internals of the water heater should all be included on your checklist.

  • It is critical to keep a watch on these elements because they are the ones that are causing the issue.

1. The Water Heater Itself

We’ll start with your hot water tank, which is the most likely suspect in this malfunction.If you’ve used this gadget for a long period of time, it’s possible that symptoms of wear and tear have already shown.Every time it is used, you may notice some corrosion, whirling noises, and leaks in the system.Because of the tank’s age, expect the water heater to trip the circuit breaker on a regular basis.

  • Failure in the thermostat is never impossible, even if you’ve purchased a brand new heater, on the other hand.
  • The thermostat is in charge of controlling the temperature of the water heater element.
  • If the thermostat fails to work properly, the heater may heat up to temperatures more than 180 degrees, causing the circuit breaker to trip due to overload.
  • The water heating element is the next component.
  • Because so many individuals ignore these pieces, they aren’t aware of the amount of rust that has accumulated on their casings.
  • Consequently, the element’s housing breaks down, allowing water to enter and cause a short circuit in the electrical components.
  • Another item to look for is any damage to the electric water heater’s general wiring.
  • Wires tend to degrade with time, and rodents that nibble through the insulation are a problem as well.
  • Damaged wires should be handled with extreme caution.
  1. Not only are short circuits possible, but there is also the possibility of electrocution.

2. A Short Circuit in The Wiring Lines

When we talk about wiring, we aren’t only referring to the lines that go from the water heater.Keep an eye out for the connectors that link the dedicated CB to the water tank.- However, there are occasions where they are not adequately fished through the conduits/wire protectors, leaving them exposed to adverse weather and other environmental circumstances.If you’re a do-it-yourselfer and don’t have the proper equipment for a fault search, it might be difficult to figure out where the short circuit is coming from.

  • The majority of the time, wires are hidden within small locations that only mice can access, thus there are only two options for locating the damage.
  • The first is accomplished by manually removing all of the cables and inspecting them, and the second is accomplished via the use of specialized gear such as a multimeter.
  • In any case, damage discovered in a series of wires can be a significant contributing factor to an electric water heater’s inability to stop tripping the breaker.

3. Circuit Breaker Malfunction

There are a variety of ways in which a circuit breaker might exceed its capacity.Despite the fact that this is the component that receives the least attention when the water heater trips the breaker, it is still important to check on it on a regular basis.After years of constant use, the usability of a circuit breaker diminishes, just as it does with other appliances or electrical gadgets.Consumer Product Safety Commission (CPSC) estimates that a CB should have a service life of at least 30-40 years, depending on how consistent the voltages and power ratings are.

  • Make certain that the circuit breaker you choose is the appropriate size for your water heater.
  • It would be unwise to use, for example, a 25-amp circuit breaker to power a 4500-watt tank because it would not provide enough room to accommodate the continuous demand.
  • As a result, in order to prevent tripping the water heater breaker, 30-amps is frequently the ideal choice for powering the entire heater without generating an issue.
  • On the other hand, if you use a breaker that has a considerably larger amperage rating than the one that was intended, the breaker will not detect any abnormalities from the heating device.
  • If the breaker never trips again, that would be great, but you won’t appreciate it nearly as much if your house is on fire because of hot wires that went unnoticed for a long period of time.

Perform a Troubleshoot

Now that I’ve outlined some of the potential reasons of this electrical problem, you’ll need to conduct a troubleshooting procedure to determine which of them is the root cause of the tripped hot water heater breaker.Here are some useful strategies for dealing with each of the negative aspects at hand: Turn off the water heater’s power source and thoroughly examine the upper and lower thermostats, as well as the heating elements.Check the wiring of the thermostat using a multimeter to discover if there is any impedance in the system (Ohmic resistance).A measurement of 0 ohms should be obtained with an open thermostat, while a reading of 0.50 to 0.50 ohms is acceptable with a closed thermostat.

  • (See Figure 1).
  • In any other case, you have a faulty thermostat that has to be replaced.
  • Assuming that the thermostats are in proper working order, remove the wires from the two terminal screws of the water heating element.
  • Turn on your multimeter’s continuity setting (with sound), and then use the two probes to make contact with the screws.
  • If the multimeter does not emit a beep, it signifies that the element is not functioning.
  • If, on the other hand, it beeps, which is a positive sign, go to the next step: connect one probe to one terminal screw and the second probe to the tank itself.
  • Next, with one probe still on the tank, attach the other probe to the second terminal screw using the same procedure as before.
  • If your multimeter did not generate a beep when you turned both screws, your heating element is in good working order.
  • Finally, examine the tank’s outside to see if there is any noticeable damage.

What Can You Do to Fix the Issue

It is necessary to repair component parts or perform wire maintenance after you have determined the source of your problem.The greatest thing you can do is gather the necessary resources, but I strongly advise against taking on all of the labor alone at this point.if the water heater circuit breaker keeps tripping, get in touch with an electrician or a reputable plumber right away.The worst thing we want to avoid is overlooking any major issues that we haven’t addressed in this lesson, complications that can only be resolved by a professional contractor with much experience.

Conclusion

Your water heater is constantly tripping the circuit breaker, and the solution is straightforward: you have either a broken breaker, an inoperable heating element, or damaged wiring.It is vital for you to determine the source of the irregularities in order to resolve the situation properly.Is it a problem with the water heater’s internals?A misplaced comma in the incorrect place?

  • Or is it simply the circuit breaker that has to be replaced?
  • Although you may use a multimeter to help you find the source of the problem, you should seek expert assistance when it comes time to repair and maintain your vehicle.

Water Heater Keeps Tripping The Breaker: Causes and Solutions

A deeper look at the system is necessary when your water heater continues to trip the circuit breaker on a regular basis.The circuits that supply water heaters are often not linked to any other devices.This implies that if the breaker trips, it is only as a result of the water heater.Sometimes there is no specific explanation for these sporadic excursions, and you may simply restart the computer and let it to continue working at its normal speed until it happens again.

  • However, if this becomes a regular occurrence, you must investigate the root reason and conduct a more thorough investigation into the problem.
  • If you’re stumped as to why your water heater keeps tripping the breaker, keep reading to find out what’s causing the circuit breakers on your heating system to trip and how to resolve the problem.

5 Reasons Why Your Water Heater Might be Tripping the Breaker

As soon as you’ve identified the problem, you’ll need to look into the root cause of the recurring trippings. Fortunately, diagnosing and repairing a broken water heater is a straightforward process. Here are 5 reasons why your water heater continues tripping the breaker, as well as remedies to each of these problems.

1. A Faulty Thermostat 

To prevent the water from overheating and scorching your skin, every water heater is equipped with a temperature control switch that is limited to 180° Fahrenheit.Additionally, these appliances often include two thermostats that are each connected to a separate heating element that warms the water.Because of the connection between these two thermostats, only one of the elements may be heated at a time.A broken thermostat, on the other hand, will interfere with communication, allowing both components to heat up at the same time.

  • Because of this, the circuit will become overheated, and the circuit will become overloaded with current, resulting in the trip of the breaker.

How to Fix the Problem

It is necessary to cut off the electricity and examine the thermostat with a multimeter once it has been turned off.The resistance level in each thermostat will be determined with the use of a digital multimeter.The resistance for a (NO) thermostat should be near to zero ohms, however the resistance for a (NC) thermostat may be close to 0.5 ohms, depending on the thermostat.If the limit is exceeded, you will need to have the thermostats replaced immediately.

  • To verify that the heating components and thermostat are compatible with one another, it’s also a good idea to replace them.

2. Malfunctioning Heating Element

It is the pair of heating elements that is responsible for heating your water, and if any of them fails, it might result in a short circuit.For example, if a heating element fails, the water will not be sufficiently heated.A short circuit can occur if the internal electrical components of the element are brought into direct contact with the water, which is a bad outcome in some cases.Similarly to the last case, the water heating element can fail and continue to heat the water without taking a break, causing the circuit to overheat and trip the breakers.

How to Fix This Issue 

  • A multimeter will be required once more in order to diagnose and repair faulty water heating components. Disconnect the wires from the problematic elements and turn off the electrical power to the entire building. Followed by measuring the resistance on either side of the heating elements, which should have been done with the multimeter when the wires were first joined. Depending on the wattage, you should obtain a reading for resistance that looks like this: A 3,500-watt element has a resistance of 16 ohms
  • a 4,500-watt element has a resistance of between 12 and 13 ohms
  • and a 5,500-watt element has a resistance of between 10 and 11 ohms.

If the readings do not match, it is apparent that the heating element is not working properly. In this instance, the only alternative available to you is to have them changed as soon as possible.

3. Leaky Water Lines

If the readings do not match, it is apparent that the heating element is faulty. It is imperative that you have them changed as soon as possible in this scenario.

How to Fix This Issue

The only way to resolve this issue is to have the leaking pipes repaired. Inspection and repair of the defective pipe should be carried out after the electrical power has been disconnected. Poor maintenance of water pipes can also result in leaky water pipes. Here’s where you can learn more about the optimal maintenance schedule for your water heating equipment.

4. Faulty Electrical Connections

It is most likely that the electrical line is the source of the problem if all of the other components of the water heating equipment are in excellent shape.If you believe this to be the case, you should begin your check with the connection between the water heating device and the main electrical line in your home’s electrical panel or panelboard.A tripped breaker may be caused by a burned wire, a loose connection, or a faulty electrical component, among other possibilities.Arced wires are another important source of risk.

  • It is possible that in this circumstance, the energy will jump from one wire to another, causing the line to lose continuity.
  • If you’ve completed your inspection of the internal electrical wiring and have not discovered a problem, it’s possible that the problem is located outside the water heater.
  • Examine the exterior wires that are attached to the appliance for evidence of damage or burns, and replace them if necessary.
See also:  How To Clean Filter On Water Softener?

5. Inspect the Breaker

  1. If everything appears to be in working order, yet the breaker keeps tripping, the issue is most likely with the breaker itself, not with the rest of the system.
  2. After prolonged operation, circuit breakers may become brittle and trip when even the smallest amount of energy is applied.
  3. In any of these situations, all that is required is the repair or replacement of the faulty electrical component or components.
  4. When changing a breaker, however, it is important to pay attention to the rating.
  5. The replacement component should be rated at the same level as the original part.
  6. Choosing a breaker with a greater or lower rating will cause the flow of electricity to be unbalanced, resulting in system disruption.

Final Thoughts

  1. There are a variety of reasons why your water heater continues tripping the breaker, as well as possible remedies.
  2. Annual maintenance can extend the life of your heater by many years.
  3. Tripping breakers are a regular problem in every household, and you should have no need to be alarmed about it.
  4. Just make sure that if it keeps tripping, you don’t keep trying to flip it back and forth.
  5. This will result in overheating of the electrical cables and, in extreme cases, can result in an electric fire.
  6. When it comes to electrical concerns, it’s always better to follow all safety measures, and if you find the task to be too tough for you, don’t hesitate to seek the assistance of a qualified professional..

You might be interested in the following: Discover how a hot water heater operates.An Explosion in a Water Heater: Its Causes, Warning Signs, and Preventative Measures

Electric Space Heater Trips Circuit Breaker: Common Causes & Solutions

  1. Electric space heaters are a godsend during the colder months of the year since they keep our homes warm and comfortable.
  2. Many space heater customers, on the other hand, have reported problems when their electric space heater trips the circuit breaker.
  3. The fact that your space heater is constantly tripping the circuit breaker may indicate that it is sending out a warning signal that you should not ignore.
  4. This post will assist you in resolving the issue so that your machine may function properly again without the need to reset the circuit breaker on a regular basis.

3 Reasons Why Your Heater Can Trip the Circuit Breaker

If your heater continues tripping the circuit breaker, you must determine why this is occurring in order to avoid a potentially dangerous situation. Listed below are three frequent reasons for space heaters to trip their circuit breakers.

Electrical Overload

  1. If you connect a large number of devices to a single circuit and operate them all at the same time, the load on the circuit may exceed the capacity of the electrical circuit.
  2. A circuit overload occurs when your space heater pulls an excessive amount of electricity from the circuit, resulting in the circuit breaker immediately shutting down to ensure your safety.
  3. The overload causes the overcurrent safeguard device in your electric panel to trigger the circuit breaker, resulting in the power being turned off.
  4. This avoids any potential electricity-related hazard, such as a fire, from occurring as a result of the overload.

Wire Heat Up

In certain cases, overloading a circuit with too many appliances might result in the fuse blowing out completely. Overloading causes the wires to overheat, resulting in the circuit tripping. When a fuse bursts, the metal filament within it is scorched, which can cause damage to the connections around it to short circuit.

Worn Out Circuit Breaker

When breakers become worn out, they begin to trip on a regular basis because they become less efficient at handling the energy flow. Breakers that are too old or worn out may also malfunction, making them potentially hazardous to the public.

How to Prevent a Space Heater from Blowing Fuse

There are several fundamental safety measures that you should follow in order to avoid a space heater tripping the breaker. These measurements are as follows:

Don’t Overload Circuits

  1. Electric space heaters cause a circuit breaker to trip when the circuit is overloaded and cannot take any more energy flow from the heater.
  2. If you have more than one heater running on the same circuit, it is possible that the fuse could blow and the circuit will trip.
  3. Examine the circuit to see if any other electrical appliances are hooked into the circuit to ensure that the circuit load does not exceed the capacity of the circuit.
  4. Because each appliance draws electricity, the overall current drawn by the circuit may be too great for the circuit to handle.
  5. When a gadget is connected in, even if it is not in use, the current flows through it and out the other end.
  6. As a result, disconnect any other electrical devices that may be causing a problem in order to decrease the load on the circuit.

Check Your Heater Settings

If your circuit is not overloaded, you could want to double-check the settings on your space heater. The majority of heaters have two temperature settings: high and low. If your heater has more than one heating setting, try resetting it and running it on the lowest level to see if it makes a difference. Your heater may quit tripping the circuit breaker when it is set to ″Low″ heat setting.

Check the Heater Wires

  1. Make sure to inspect the heater’s internal and external wiring for signs of damage on a regular basis, since defective wiring might result in bursts of electricity that can cause fires.
  2. If the wire in your space heater is broken, the fuse will most likely melt in order to safeguard the other components of the heater.
  3. However, even after the fuse has melted, the overcurrent continues to pose a hazard to the heater’s components.
  4. Keep an eye on your heater once a month for any indications of wear and tear to prevent the possible dangers of frayed or broken wiring.
  5. In addition, inspect the rubber casings on the wires and replace them if they appear to be damaged.
  6. If your space heater is brand new, but the wires are broken, it is possible that there was a manufacturing defect, in which case you will need to repair or return the item for a refund.

It is not recommended to use the space heater until the broken wires have been repaired.

Add New Outlets

  1. You can try moving the device to a different outlet that does not trigger the circuit breaker if the problem persists.
  2. This might assist you in determining if the problem is with the circuit or with your heater.
  3. You may need to create a new outlet for your space heater if the problem is with the circuit.
  4. This will prevent any additional load from being placed on other circuits.
  5. You may also want to consider utilizing a surge protector, which are power strips that are built to resist a power surge in order to prevent harm to other electrical devices.

Safety Tips for Circuit Trips

  • Following a trip of your electric space heater’s circuit breaker, you should take the following procedures to protect the safety of both the heater and your home. Here are some important safety precautions to remember: It is essential to ensure that your space heater is installed on a level surface at all times.
  • Maintain a safe distance between your space heater and other electrical equipment and combustible materials, such as beds and drapes.
  • Keep space heaters out of the children’s bedrooms at all times! If it is required to place one, make sure it is at least three feet away from any other objects in the enclosed space.

Summary

  1. The fact that your electric space heater trips the circuit breaker every time it does so is actually a warning to you.
  2. As a result, it is not recommended to continually resetting the device or connecting it into the same circuit again and over.
  3. To avoid a space heater blowing a fuse, make sure the circuit is not overloaded, and examine the heater’s settings and wiring.
  4. You may also install a surge protector.
  5. Also, when using a space heater in your home, make sure to adhere to all applicable safety precautions.

Water Heater Tripping Your Breaker? Follow These 5 Steps

  1. Are you becoming increasingly irritated because your circuit breaker keeps triping?
  2. If this is the case, the source of the problem might be your water heater.
  3. Water heaters are classified into two categories.
  4. The first type of water heater is referred to as a gas water heater.
  5. The second type of water heater is referred to as an electric water heater.
  6. If your gas water heater requires electricity to operate, there is a danger that it will trip your circuit breaker.

Both types of water heaters have the potential to trip a circuit breaker.If your water heater is tripping your circuit breaker on a regular basis, there are numerous things you should look at.Check the thermostat, the heating element, the internal wiring, and the electrical system as a whole to make sure everything is working properly.You should also check for any other appliances that might be causing the circuit breaker to trip as well.You rely on your hot water heater to function effectively, and when it fails to do so, it may be quite annoying.Despite the fact that you may be under a great deal of pressure, we have conducted extensive study to determine the most common reasons why water heaters trip circuit breakers in the first place.

  • Consider the findings of our investigation and see if you can determine why your water heater keeps tripping the circuit breaker.
  • Are you prepared to investigate your electric water heater in greater depth?
  • If this is the case, continue reading and let’s see if we can figure out why your electric water heater is not functioning properly.

Why Does a Circuit Breaker Trip?

  1. Now, you might be asking why your circuit breaker is tripping in the first place.
  2. An electric water heater can overload one or more of your appliances, which is why your circuit breaker has been carefully built to prevent this from happening.
  3. Whenever a circuit breaker detects that anything dangerous is happening in your electrical system, it will shut off the electricity to that portion of the house.
  4. You could believe that merely leaving the circuit breaker open would fix the problem; however, this should never be done under any circumstances.
  5. A cause for your circuit breaker to be shutting off has been identified; nevertheless, you must ascertain what that reason is.
  6. It is possible that you will overload one or more of your appliances if you decide to leave your circuit breaker open for an extended period of time.

It has the potential to cause an electrical fire.As a result, you must gather the necessary resources in order to conduct a thorough examination of your water heater.You will be able to find out what is going on and correct it this way.

Materials Needed To Fix an Electric Water Heater

  • If you want to repair your electric water heater, you’ll need a few essential supplies. Some of the materials you’ll need are as follows: You will want access to your electric water heater in order to do this task. This is often kept in the garage or in a utility closet
  • nonetheless,
  • Furthermore, a torch will be required in order to see properly behind the electric water heater
  • and
  • To figure out where all of the separate pieces are located, you should have access to the owner’s handbook.
  • If you need to disassemble any of the water heater’s components, you’ll most likely need a basic toolbox as well.
  • When working around the water heater, make sure you have enough of towels on hand in case any water leaks.
  • Furthermore, a multimeter must be brought with you in order to test each individual component of the water heater.

After you have acquired all of the essential supplies, you can proceed to your water heater and attempt to determine what is causing the problem there. What are some of the steps you’ll need to take to get started?

Fix an Electric Water Heater in 5 Steps

If you want to figure out why your water heater keeps tripping the circuit breaker, there are a few measures you need to do to get there. These are some examples:

Step 1: Look at the Other Appliances

  1. First and foremost, you must examine the circuit breaker and determine whether or not any other appliances are connected to the same circuit as your water heater.
  2. Examples include additional appliances that have been connected into neighboring outlets and which may have been a contributing factor in the circuit breaker being tripped.
  3. Alternatively, someone might have unknowingly connected another item to the same circuit without your knowledge.
  4. Check anything that is linked to the same circuit while it is being tested.
  5. After that, check to see if anything has been connected that shouldn’t be there.
  6. If you can identify something else that has recently been added to the circuit, it is likely that this is the source of the circuit breaker’s incessant tripping.

Disconnect the new appliance from the circuit and reinstall it.After that, observe whether or not the circuit breaker operates as it should.If this is the case, your water heater was not the source of the problem, but another item.

Step 2: There Might Be a Bad Thermostat

  1. If you suspect that the source of the problem is your water heater, the first thing you should do is check the temperature setting on the thermostat.
  2. Water heaters are often equipped with a limit switch that prohibits the water from reaching temperatures higher than 180 degrees Fahrenheit.
  3. If the water gets too hot, a limit switch is activated, which prevents the water from being any hotter than it already is.
  4. In order to avoid getting burnt, it is essential that you do this.
  5. A large number of water heaters contain two thermostats and two heating components, for a total of four.
  6. Each heating element is equipped with its own thermostat.

Typically, the thermostats communicate with one another in order to ensure that only one element of the water heater is heating at a given moment.The water heater may start heating both elements at the same time if the thermostat becomes locked in the ″on″ position for an extended period of time.Because of this, the electrical circuit may experience a substantial pull in power, resulting in the circuit breaker tripping.A multimeter will be required if you want to take a closer look at the thermostat.Make use of the multimeter to check each individual thermostat to ensure that it is functioning properly.If the readings from each thermostat are significantly different, it is likely that one of them is malfunctioning.

  • Most likely, the thermostat is not working properly because it does not have a lot of resistance or electricity running through it.
  • It’s possible that it will need to be replaced.

Step 3: A Bad Heating Element

  1. In addition to a faulty thermostat, it is possible that the heating element is malfunctioning.
  2. The individual heating components must be examined in the same way that the thermostats were examined above in order to diagnose the problem.
  3. If your water heater has two independent heating components, you must inspect each one individually to ensure that they are both operating properly.
  4. It is possible that an older heating element will have an issue with the casing.
  5. After a period of time, the casing around the heating element begins to fracture, exposing the electrical section of the water heater.
  6. Because of this, it is possible for the heating element to short circuit, resulting in the trip of a limit switch.
See also:  How Much To Install A Whole House Water Filter?

This will cause the circuit breaker to trip, resulting in the water heater being turned off.There is also the possibility that the element will continue to function even when it is not meant to.Consequently, the water will get too hot, causing the limit switch to be tripped.This might potentially cause the circuit breaker to trip, resulting in the water heater being turned off.In order to test the various heating elements, you’ll need to make use of your multimeter.This is a sign that the heating element is damaged and must be changed if the resistance reading does not match the expected value.

Step 4: Check for a Water Leak

  1. It goes without saying that you must inspect the water heater to ensure that there is no water leaking from the heater.
  2. Many older water heaters are susceptible to developing leaks.
  3. If this is the case, water may begin to gravitate toward all of the electrical elements in the area.
  4. In order to avoid injury when working on your water heater, you must always prioritize safety first.
  5. If there is standing water surrounding the water heater, it is possible that it will come into touch with one of the electrical components.
  6. This has the potential to create a catastrophic electrical shock and maybe cause the entire system to short circuit.

If you notice a leak in the water heater, you must shut down the power to the unit immediately.Make certain that no electricity is being supplied to the water heater at all times.Afterwards, you may take a closer look at the water heater to determine what steps you need take to resolve the problem.It’s possible that you’ll need to hire an expert to assist you with this.

Step 5: Look at the Internal Wiring

  1. Finally, there might be an issue with the water heater’s internal wiring, which would cause it to malfunction.
  2. If you are not an electrician, you may wish to seek the assistance of an electrician to complete this step for you.
  3. Before you begin working on the water heater’s internal wiring, you must first turn off the circuit breaker and turn off the electricity to the water heater.
  4. When you examine the interior wiring, you are searching for any indications of faulty wires or connections.
  5. There might be a symptom of corrosion in the water heater at some point in the future.
  6. Alternatively, you may detect the smell of smoke emanating from some of the cables.

If this is the case, it is possible that there is a serious problem with the internal components of the tank water heater.You should consult with a specialist to determine if it is more cost effective to fix these cables or to have the complete system replaced.

Solve the Mystery of Your Water Heater

  1. After all is said and done, these are just a few of the numerous reasons why your electric water heater may be continuously tripping your circuit breaker.
  2. If your electric water heater is not performing as expected, it is easy to become frustrated.
  3. However, it is important to remember that there is a reason why the circuit breaker keeps tripping on and off.
  4. Under no circumstances should you ever attempt to force your circuit breaker to remain closed.
  5. This has the potential to be a significant safety hazard.
  6. If you have followed all of these steps and are still unable to determine why your electric water heater is not functioning properly, you should seek the assistance of a professional who can assist you.

It is possible that you may want the services of a plumber or an electrician to determine what is wrong with your electric water heater.

Water Heater Tripping Your Breaker? Follow These 5 Steps

  1. Are you becoming increasingly irritated because your circuit breaker keeps triping?
  2. If this is the case, the source of the problem might be your water heater.
  3. Water heaters are classified into two categories.
  4. The first type of water heater is referred to as a gas water heater.
  5. The second type of water heater is referred to as an electric water heater.
  6. If your gas water heater requires electricity to operate, there is a danger that it will trip your circuit breaker.

Both types of water heaters have the potential to trip a circuit breaker.If your water heater is tripping your circuit breaker on a regular basis, there are numerous things you should look at.Check the thermostat, the heating element, the internal wiring, and the electrical system as a whole to make sure everything is working properly.You should also check for any other appliances that might be causing the circuit breaker to trip as well.You rely on your hot water heater to function effectively, and when it fails to do so, it may be quite annoying.Despite the fact that you may be under a great deal of pressure, we have conducted extensive study to determine the most common reasons why water heaters trip circuit breakers in the first place.

  • Consider the findings of our investigation and see if you can determine why your water heater keeps tripping the circuit breaker.
  • Are you prepared to investigate your electric water heater in greater depth?
  • If this is the case, continue reading and let’s see if we can figure out why your electric water heater is not functioning properly.

Why Does a Circuit Breaker Trip?

  1. Now, you might be asking why your circuit breaker is tripping in the first place.
  2. An electric water heater can overload one or more of your appliances, which is why your circuit breaker has been carefully built to prevent this from happening.
  3. Whenever a circuit breaker detects that anything dangerous is happening in your electrical system, it will shut off the electricity to that portion of the house.
  4. You could believe that merely leaving the circuit breaker open would fix the problem; however, this should never be done under any circumstances.
  5. A cause for your circuit breaker to be shutting off has been identified; nevertheless, you must ascertain what that reason is.
  6. It is possible that you will overload one or more of your appliances if you decide to leave your circuit breaker open for an extended period of time.

It has the potential to cause an electrical fire.As a result, you must gather the necessary resources in order to conduct a thorough examination of your water heater.You will be able to find out what is going on and correct it this way.

Materials Needed To Fix an Electric Water Heater

  • If you want to repair your electric water heater, you’ll need a few essential supplies. Some of the materials you’ll need are as follows: You will want access to your electric water heater in order to do this task. This is often kept in the garage or in a utility closet
  • nonetheless,
  • Furthermore, a torch will be required in order to see properly behind the electric water heater
  • and
  • To figure out where all of the separate pieces are located, you should have access to the owner’s handbook.
  • If you need to disassemble any of the water heater’s components, you’ll most likely need a basic toolbox as well.
  • When working around the water heater, make sure you have enough of towels on hand in case any water leaks.
  • Furthermore, a multimeter must be brought with you in order to test each individual component of the water heater.

After you have acquired all of the essential supplies, you can proceed to your water heater and attempt to determine what is causing the problem there. What are some of the steps you’ll need to take to get started?

Fix an Electric Water Heater in 5 Steps

If you want to figure out why your water heater keeps tripping the circuit breaker, there are a few measures you need to do to get there. These are some examples:

Step 1: Look at the Other Appliances

  1. First and foremost, you must examine the circuit breaker and determine whether or not any other appliances are connected to the same circuit as your water heater.
  2. Examples include additional appliances that have been connected into neighboring outlets and which may have been a contributing factor in the circuit breaker being tripped.
  3. Alternatively, someone might have unknowingly connected another item to the same circuit without your knowledge.
  4. Check anything that is linked to the same circuit while it is being tested.
  5. After that, check to see if anything has been connected that shouldn’t be there.
  6. If you can identify something else that has recently been added to the circuit, it is likely that this is the source of the circuit breaker’s incessant tripping.

Disconnect the new appliance from the circuit and reinstall it.After that, observe whether or not the circuit breaker operates as it should.If this is the case, your water heater was not the source of the problem, but another item.

Step 2: There Might Be a Bad Thermostat

  1. If you suspect that the source of the problem is your water heater, the first thing you should do is check the temperature setting on the thermostat.
  2. Water heaters are often equipped with a limit switch that prohibits the water from reaching temperatures higher than 180 degrees Fahrenheit.
  3. If the water gets too hot, a limit switch is activated, which prevents the water from being any hotter than it already is.
  4. In order to avoid getting burnt, it is essential that you do this.
  5. A large number of water heaters contain two thermostats and two heating components, for a total of four.
  6. Each heating element is equipped with its own thermostat.

Typically, the thermostats communicate with one another in order to ensure that only one element of the water heater is heating at a given moment.The water heater may start heating both elements at the same time if the thermostat becomes locked in the ″on″ position for an extended period of time.Because of this, the electrical circuit may experience a substantial pull in power, resulting in the circuit breaker tripping.A multimeter will be required if you want to take a closer look at the thermostat.Make use of the multimeter to check each individual thermostat to ensure that it is functioning properly.If the readings from each thermostat are significantly different, it is likely that one of them is malfunctioning.

  • Most likely, the thermostat is not working properly because it does not have a lot of resistance or electricity running through it.
  • It’s possible that it will need to be replaced.

Step 3: A Bad Heating Element

  1. In addition to a faulty thermostat, it is possible that the heating element is malfunctioning.
  2. The individual heating components must be examined in the same way that the thermostats were examined above in order to diagnose the problem.
  3. If your water heater has two independent heating components, you must inspect each one individually to ensure that they are both operating properly.
  4. It is possible that an older heating element will have an issue with the casing.
  5. After a period of time, the casing around the heating element begins to fracture, exposing the electrical section of the water heater.
  6. Because of this, it is possible for the heating element to short circuit, resulting in the trip of a limit switch.

This will cause the circuit breaker to trip, resulting in the water heater being turned off.There is also the possibility that the element will continue to function even when it is not meant to.Consequently, the water will get too hot, causing the limit switch to be tripped.This might potentially cause the circuit breaker to trip, resulting in the water heater being turned off.In order to test the various heating elements, you’ll need to make use of your multimeter.This is a sign that the heating element is damaged and must be changed if the resistance reading does not match the expected value.

Step 4: Check for a Water Leak

  1. It goes without saying that you must inspect the water heater to ensure that there is no water leaking from the heater.
  2. Many older water heaters are susceptible to developing leaks.
  3. If this is the case, water may begin to gravitate toward all of the electrical elements in the area.
  4. In order to avoid injury when working on your water heater, you must always prioritize safety first.
  5. If there is standing water surrounding the water heater, it is possible that it will come into touch with one of the electrical components.
  6. This has the potential to create a catastrophic electrical shock and maybe cause the entire system to short circuit.

If you notice a leak in the water heater, you must shut down the power to the unit immediately.Make certain that no electricity is being supplied to the water heater at all times.Afterwards, you may take a closer look at the water heater to determine what steps you need take to resolve the problem.It’s possible that you’ll need to hire an expert to assist you with this.

Step 5: Look at the Internal Wiring

  1. Finally, there might be an issue with the water heater’s internal wiring, which would cause it to malfunction.
  2. If you are not an electrician, you may wish to seek the assistance of an electrician to complete this step for you.
  3. Before you begin working on the water heater’s internal wiring, you must first turn off the circuit breaker and turn off the electricity to the water heater.
  4. When you examine the interior wiring, you are searching for any indications of faulty wires or connections.
  5. There might be a symptom of corrosion in the water heater at some point in the future.
  6. Alternatively, you may detect the smell of smoke emanating from some of the cables.

If this is the case, it is possible that there is a serious problem with the internal components of the tank water heater.You should consult with a specialist to determine if it is more cost effective to fix these cables or to have the complete system replaced.

Solve the Mystery of Your Water Heater

  1. After all is said and done, these are just a few of the numerous reasons why your electric water heater may be continuously tripping your circuit breaker.
  2. If your electric water heater is not performing as expected, it is natural to become irritated.
  3. However, it is important to realize that there is a reason why the circuit breaker continues tripping on and off.
  4. Under no circumstances should you ever attempt to force your circuit breaker to remain closed.
  5. This has the potential to

Leave a Reply

Your email address will not be published.