What Size Socket For Water Heater Element

What Size Socket for Water Heater Element

It is necessary to use a Drive x 1-1/2 inches socket to connect the water heater element. This socket’s aperture is designed to adequately accommodate all standard size electric heater elements, and the hex end will fit snuggly into the opening. This is done in order to allow you to utilize the most suitable torque while being non-slip. On a similar point, the socket for the heating element should be 1.5 inches in diameter at the smallest. However, for an anode, a 1-1/16-inch socket should be used.

How a Water Heater Element Works

When it comes to electric water heaters, the most common issues are with the water heater components and electrical wiring. If you have hot water that runs out rapidly, it is possible that your bottom heater element is malfunctioning. However, if your water heater takes a long time to recover after being subjected to a large amount of water, the upper element may be the source of the problem. A certain amount of resistance is encountered when power is passed through the water heater element. This resistance generates quick heat, much to the friction created by rubbing your hands together.

It is critical to test your element in order to determine whether it is functional or not.

You’ll need a screwdriver, a wrench, and a garden hose to complete the replacement.

How to Loosen a Heating Element

Listed below are some tools that will assist you in removing the bolts and trapped heating components.

  1. Bend the wires that connect to the water heater element. In a small cup, combine half water and half vinegar
  2. Set aside. Turn the heating element anti-clockwise by inserting the socket into it. Dip a brush into the solution and use it to clean the space between the side of the heating tank and the heating element. When applying the solution, avoid allowing it to become too saturated. It should be left on for 20 minutes before being removed once it has been applied.

How to Replace the Heating Element in an Electric Hot Water Heater

In order to replace the heating element in your electric tankless water heater, you do not have to drain the tank first. You should be aware, however, that you will not be able to drain the heater at a high degree. Just because your heating element is not functioning properly does not imply that you must replace it. Sometimes all you need to do is replace the component and you’re set to go. While this procedure appears to be difficult, if you have the necessary abilities and resources, you may complete it successfully on your own.

How to Replace a Water Heater Element without Draining Tank

To accomplish this in a safe manner, you must first turn off the water supply to the water heater at the source. Make certain that no faucets in the home are running. This is done in order to prevent air from entering the tank. After that, place a bucket under the water heater drain and then release the drain valve to enable the pressure to escape the tank of the heater. Once you are finished, delete the old element and replace it with the new one. The possibility of getting wet exists if the water valve does not shut properly or if your faucets are dripping.

Wrapping

The information provided above contains all of the information you want on water heater element size and how to replace a water heater element.

If you are unsure about any aspect of the procedure, seek expert advice.

What size socket fits a hot water heater element?

Water Heater Socket with a 1-1/2-inch drive. The 6-point opening is designed to accommodate the most common size of electric water heater element, and it tightly fits the hex end of the element so you can apply the maximum torque without sliding. 1.5″ Aside from that, what size socket do I require for an anode rod? 1-1/16″socket. It’s important to utilize a 1/2″ drivesocket, an extension (6″ to 12″), and a long-handled socket wrenchor, better yet, an electric breaker bar if you have one available.

Second, do hot water heater components have a universal application?

Using a separate four-bolt flange, the Round Headwater heater element is connected to the tank to provide heat.

What is the best way to unscrew a heating element?

  1. Bend the wires of the heating element out of the way
  2. In a tiny cup, combine half vinegar and half water to make a solution
  3. Make an attempt to spin the socket counterclockwise by positioning it above the heating element.

What size socket for electric element removal?

07-21-2020, 06:33 PM 1
MemberJoin Date: Jul 2020Posts: 33 What size socket for electric element removal?


I have a Suburban Gas/Electric water heater SW10DE, electric element part number 520789 that need to replace and need to know what size socket I need to buy so I can remove this defective element?Thanks in advance for any help.Russell

07-21-2020, 06:45 PM 2
Senior MemberJoin Date: Jan 2020Posts: 2,264
07-21-2020, 08:29 PM 3
Senior MemberJoin Date: Apr 2013Location: Santa Fe, TxPosts: 233 I�d double check. Mine isa 1 1/16_2012 F250 6.2 gasser 373 rear2013 Rockwood 2104S Mini Lite
07-21-2020, 08:30 PM 4
Senior MemberJoin Date: Jan 2020Posts: 2,264 Quote:Originally Posted byOle BuzzardI’d double check. Mine isa 1 1/16For the heating element or for the anode rod? The Camco 09883 element removal tool says it is 1 1/2 inch socket. The anode rod is indeed 1 1/16 inch.I would be careful about using the standard 1 1/2 inch deep well socket, though. You might find the socket wall thickness is too thick to fit into the recess the element screws into. I’d just stick the water heater element removal tool you can get at almost any hardware store. But it is 1 1/2 inch.
07-21-2020, 08:48 PM 5
Brake is on leftJoin Date: Jul 2019Posts: 1,092 Quote:Originally Posted byNavyLCDRI would be careful about using the standard 1 1/2 inch deep well socket, though. You might find the socket wall thickness is too thick to fit into the recess the element screws into. I’d just stick the water heater element removal tool you can get at almost any hardware store. But it is 1 1/2 inch.This. And get a 5� long element wrench. The 4� is not quite long enough to get the end past the wall of the TT.
07-21-2020, 08:50 PM 6
Senior MemberJoin Date: Jan 2015Location: KansasPosts: 1,221 On my Suburban WH. 1 1/2″ Craftsman 1/2″ drive socket works. I’m talking about the electric element with the 2 wires hooked to it, not the anode drain which is 1 1/16″PS. Go to Lowes and get their 110 volt 1500 watt element for @$7. It screws right in and only uses 1/2 amp more electricity than the 1440 watt OEM element.
07-21-2020, 09:12 PM 7
Senior MemberJoin Date: Jan 2020Posts: 2,264 Quote:Originally Posted bydieselguyOn my Suburban WH. 1 1/2″ Craftsman 1/2″ drive socket works. I’m talking about the electric element with the 2 wires hooked to it, not the anode drain which is 1 1/16″PS. Go to Lowes and get their 110 volt 1500 watt element for @$7. It screws right in and only uses 1/2 amp more electricity than the 1440 watt OEM element.Great to know!
07-21-2020, 09:24 PM 8
MemberJoin Date: Jul 2020Posts: 33 Thanks. NavyEM2 USS Saratoga 73-76
07-22-2020, 01:56 PM 9
Casino CamperJoin Date: Dec 2015Location: St Helens, OregonPosts: 178 It is 1-1/4″

Attached Thumbnails

Click image for larger versionName: ElementWrench.jpg Views: 193 Size: 229.6 KB ID: 234516_2016 Cherokee 264L (Rear Living)2013 GMC Sierra Denali2020 Nights Camped: 26 Campgrounds: 82019 Nights Camped: 11 Campgrounds: 32018 Nights Camped: 14 Campgrounds: 42017 Nights Camped: 39 Campgrounds: 12

07-22-2020, 02:13 PM 10
Casino CamperJoin Date: Dec 2015Location: St Helens, OregonPosts: 178 I apologize for my post saying 1-1/4, that is the thread diameter.Suburban Water Heater Element 520789 Replaces 232794.SW10 Approx 1-1/4″ Diameter at threads and 1-1/2″ at flange or nut.

Attached Thumbnails

Click image for larger versionName: Element.jpg Views: 81 Size: 308.1 KB ID: 234517_2016 Cherokee 264L (Rear Living)2013 GMC Sierra Denali2020 Nights Camped: 26 Campgrounds: 82019 Nights Camped: 11 Campgrounds: 32018 Nights Camped: 14 Campgrounds: 42017 Nights Camped: 39 Campgrounds: 12

07-22-2020, 02:21 PM 11
Casino CamperJoin Date: Dec 2015Location: St Helens, OregonPosts: 178 If you don’t know how it went bad here is my experience.I drained my water heater and winterized but never turned off the little switch on the water heater. I do not have an inside switch for electric.When I went to de-winterized I plugged in to shore power to fire everything up the element was on with no water in the tank. I would have thought the reset button would pop or the fusible link would blow but instead, the element stayed hot and cracked when I added water. The “snap” is quite audible when you have your head next to the tank turning the inlet valve on._2016 Cherokee 264L (Rear Living)2013 GMC Sierra Denali2020 Nights Camped: 26 Campgrounds: 82019 Nights Camped: 11 Campgrounds: 32018 Nights Camped: 14 Campgrounds: 42017 Nights Camped: 39 Campgrounds: 12
07-22-2020, 03:01 PM 12
Senior MemberJoin Date: Sep 2009Posts: 183 Home Depot or Lowes sells an element wrench. Just about any hardware store should have one. You don’t need a RV specific one.
07-22-2020, 03:20 PM 13
Senior MemberJoin Date: Jan 2020Posts: 2,264 Quote:Originally Posted byshadows4Home Depot or Lowes sells an element wrench. Just about any hardware store should have one. You don’t need a RV specific one.They sell the electric element too. Just make sure it is 1440 watt 120 volts
07-22-2020, 07:28 PM 14
Senior MemberJoin Date: Jan 2018Location: Raleigh, NCPosts: 5,272 Amazon also has the elements and wrenches._LarrySticks and Bricks: Raleigh, NC2008 Cherokee 38P: at Ivor, VA permanently
07-22-2020, 09:13 PM 15
Senior MemberJoin Date: Jan 2020Posts: 2,264 So does Ebay, Ace Hardware, Walmarr website, True Value Hardware, Grainger.
07-23-2020, 03:32 AM 16
Senior MemberJoin Date: Jul 2015Posts: 7,040 A standard 1-1/2” socket can work sometimes, but they generally have a slight taper at the end and can easily slip off of the shallow flats of a water heater element. You can get a cheap stamped metal element socket that will usually do the trick or you can buy a heavy-duty 1-1/2” element socket that is completely flat where it goes onto the element nut and use a ratchet to turn it. I am a plumber, so I use the latter because it always works and doesn’t round off the points on the element nut. It will also work with a breaker bar or impact wrench for those really old and tough-to-get-out elements without messing them up.Bruce_2016 Rockwood Windjammer 3029W Diamond Edition2015 Chevy 3500HD LTZ 6.0 Crew Cab 4×4 Long Bed 4.10:1 SRW
Posting Rules
Youmay notpost new threadsYoumay notpost repliesYoumay notpost attachmentsYoumay notedit your posts


BB codeisOn SmiliesareOn code isOnHTML code isOffTrackbacksareOff PingbacksareOff RefbacksareOff


Forum Rules

Disclaimer:This website is not affiliated with or endorsed by Forest River, Inc. or any of its affiliates. This is an independent, unofficial site.All times are GMT -5. The time now is06:40 AM.

What size socket for Electric Water Heater Element

  • When it comes to electric water heaters, what size socket wrench do you need?

Re: What size socket for Electric Water Heater Element

  • Loren Sanders Sr. originally posted this message. When it comes to electric water heaters, what size socket wrench do you need? I’m not sure how big it is, but it’s rather substantial. When you purchase a new water heater element, you can even pick up a water heater element wrench for a few bucks. I replaced my components last year, and the tool was only a few bucks, if my memory serves me well. In the event that your tank contains two components, I strongly urge that you replace them both at the same time.

Re: What size socket for Electric Water Heater Element

  • Scott Patterson had first posted this. I’m not sure how big it is, but it’s rather substantial. When you purchase a new water heater element, you can even pick up a water heater element wrench for a few bucks. I replaced my components last year, and the tool was only a few bucks, if my memory serves me well. Replace both elements at the same time if your tank has two elements, since this will save you money and time. Thank you, Scott. Considering that I already have a number of big sockets that I use to R and R Water Pressure Regulator Kits, it is possible that I will not need to acquire a separate one only for the Elements.

Re: What size socket for Electric Water Heater Element

  • Dom D’Agostino first posted this message. The majority of them are 1.5 inches. Is it 1.5 inches? Hmmm. I was under the impression that they were the size of a 24 inch pipe wrench. Former Construction Litigation Consultant, Jerry Peck, is now retired. www.AskCodeMan.com

Re: What size socket for Electric Water Heater Element

  • Jerry Peck originally posted this on his blog. Is it 1.5 inches? Hmmm. I was under the impression that they were the size of a 24 inch pipe wrench. In fact, I was considering purchasing a 60″ Tong Wrench (Chain Wrench). Thank you, Jerry, for validating a response I received from another source. I appreciate your help. Take precautions

Re: What size socket for Electric Water Heater Element

  • Loren Sanders Sr. originally posted this message. In fact, I was considering purchasing a 60″ Tong Wrench (Chain Wrench). Thank you, Jerry, for validating a response I received from another source. I appreciate your help. Take precautions. Loren, My first idea when I read your query was the 24″ pipe wrench with a cheater bar (5′ length of pipe slipped over the handle of the pipe wrench). I decided to let others answer it first since I didn’t want to give anything away. It’s not far from your 60″ Tong Wrench, actually. AskCodeMan.com is owned and operated by Jerry Peck, a retired construction litigation consultant.

Re: What size socket for Electric Water Heater Element

  • It would be the large Crescent wrench with a pipe extension on the handle that I would choose. Alternatively, it might be that I had a dream that I had installed an element in another incarnation, in the 1970s, the last time I had done so

Re: What size socket for Electric Water Heater Element

  • Loren Sanders Sr. originally posted this message. When it comes to electric water heaters, what size socket wrench do you need? Go ahead and measure the size of the hex head on a new element for your heater
  • I believe they are 1 1/4″ in diameter, but I’m not 100% sure about that. Then you may either rent or purchase an impact wrench (air or electric). The nuts are constantly seized, and the impact will easily dislodge them with minimal effort. Apply anti-seize compound to the threads of the new element so that it will not seize the next time. The beatings will continue until the situation has been rectified. mgt

Re: What size socket for Electric Water Heater Element

  • Vern Heiler originally posted this on his blog. Go ahead and measure the size of the hex head on a new element for your heater
  • I believe they are 1 1/4″ in diameter, but I’m not 100% sure about that. Then you may either rent or purchase an impact wrench (air or electric). The nuts are constantly seized, and the impact will easily dislodge them with minimal effort. Apply anti-seize compound to the threads of the new element so that it will not seize the next time. Is there a safe anti-seize substance that can be used with drinkable water? If there is such a thing, I am not aware of it.

Re: What size socket for Electric Water Heater Element

  • Loren Sanders Sr. originally posted this message. Is there a safe anti-seize substance that can be used with drinkable water? If there is such a thing, I am not aware of it. The socket measures 1.5 inches in diameter. You can get one for $6-$12 at any local hardware shop. The socket has a hole in it that may be inserted into with a screwdriver to spin the socket. When using a socket and screwdriver to remove the heating elements, they are usually quite simple to remove. Most heating elements are equipped with an O-Ring to keep them sealed, thus there is no need to use any anti-seize agent. Watch this video for an example of how to delete the element. Correct a smart man and you get a friend. It is possible to bloody your nose by correcting an idiot

Re: What size socket for Electric Water Heater Element

  • Jerry Peck originally posted this on his blog. Is it 1.5 inches? Hmmm. I was under the impression that they were the size of a 24 inch pipe wrench. You forgot about the sledgehammer to use at the end to get it to operate

Re: What size socket for Electric Water Heater Element

  1. Scott Patterson had first posted this. Replace both elements at the same time if your tank has two elements, since this will save you money and time. This is an excellent suggestion. Usually, the lower one is the one who goes first, for whatever reason. It’s possible that it’s more frequently utilized than the top. However, because you have gone to the trouble of draining the tank, you should also replace the other element. It is a good opportunity to check all of the electrical connections, including the feed, to make sure they are all secure.

Tags for this Thread

  • You are not permitted to start new posts or reply to existing ones. You are not permitted to submit attachments. You are not permitted to modify your posts.

The Rules of the Forum

Remove Water Heater Element Without Element Wrench – STEP BY STEP

In most cases, an element wrench is required to remove the water heater element since they are reliable in virtually all situations. However, it is possible that the heater element has corroded or rusted, particularly if the heater element is old. Then you may have to resort to something a little more substantial, which brings us to the question of how to remove a water heater element without an element wrench. It is necessary to use a 38mm socket in order to remove the water heater element without the need of an element wrench.

  • If you have the opportunity to do so, it is preferable to acquire an element wrench, which can be had for as little as four dollars.
  • This recommendation also applies to portable water heaters that contain a tank, if they have one.
  • Furthermore, because breaker bars are hollow steel pipes, they may be used to remove an element wrench from a heater’s socket wrench handle because they can fit over the handle of the heater’s socket wrench.
  • In most cases, an element wrench should be used to remove the water heater element from the tank.
  • In order to remove a recalcitrant water heater element that you have been unable to remove on your own, you must purchase a socket.

Without the use of an element wrench, how do you remove the water heater element? Method #1: Remove the water heater element without the use of an element wrench. Most socket sets include a 38″ socket, which is very common.

Step by Step How To Remove Water Heater Element Without Element Wrench

  • We’ll need to use a voltage tester to make sure that no energy is still flowing to the water heater after we’ve turned off the circuit breaker. Using a hose, we can see if any sediments have stopped our drain valve. In order to remove the cover for the access panel, you’ll need a screwdriver.

The time required is 8 minutes. In a few simple steps, you will learn how to remove a water heater element without the need of an element wrench.

  1. Turn off the circuit breaker if necessary. Double-check to see that the circuit breaker at the electrical panel has been switched off before continuing. It is possible to establish whether or not power is reaching the water heater with the use of a voltage tester. When removing the element from a water heater, the most critical safety consideration is to ensure that there is no electricity present
  2. Otherwise, the element might be damaged. Installation of the hose Beginning with the hookup of the hose to the water heater when no electricity is available, proceed as follows: The goal of this step is to assess whether or not any sediments have accumulated and obstructed our drain valve at this time. Because of this, we do not have to empty our water tank when carrying out this procedure. Turn off the water supply. In order to accomplish this procedure, we must turn off the water supply valve. Turning off the water supply is as simple as closing the water inlet valve, which is a straightforward process that can be seen above the water heater and is accessible. By enabling air to enter the tank, we will be able to release the hot water that has been stored within the water heater. The final step in this procedure would be to turn on the hot water by opening the tap that is closest to the faucet. Removal of the Cover for the Access Panel It is necessary to remove the cover from the access panel. The screwdriver will be used to remove the cover from the access panel, which will be our technique of doing so today. On the thermostat of the water heater, there is also a clear plastic cover visible. It is necessary to remove this with care. At this point, it is necessary to examine the wiring as well. Is there anything that appears to be damaged or melted? We must understand that any broken wires must be replaced as soon as possible in order to prevent future harm. We will need to release the screw in order to disconnect the heating element wires from the heating element. Removing the water heater element without the use of an element wrench is possible. A socket can now be used in place of the standard element wrench in the following situations. a standard inch and a half (38 mm) will be used as the socket size
  3. Before putting in the new element, clean it well. It is now possible to clean and wipe the new element. It is necessary to take specific precautions in order to avoid contaminants and debris from being transported to our water heaters. The new “O” ring will be attached to our new heating element at this point. It is now possible to carefully place the element into its tank and tighten it with the element wrench once it has been joined with the “O” ring. It is not suggested that you do this process using a regular wrench. Adding Water to the Water Heater’s Storage Tank Closing the drain valve while also turning on the water supply to the heater are both recommended. At this moment, I do not recommend that the power supply be switched on soon after being disconnected. It is critical that we verify that our tank is completely filled before turning on the electricity. As of right now, a half-full container of water has the potential to cause harm to the heating element. To proceed to the following stage, you must visually inspect the freshly installed part for any symptoms of leaking. The water supply should be turned off and the element should be tightened until no more water is coming out. In certain circumstances, the “O” ring may also need to be moved
  4. However, this is not always the case. Replace the cover of the thermostat and turn on the circuit breaker. After the tank has been completely filled, the thermostat cover, the insulation, and the access panel cover can all be removed and replaced with new parts. As soon as we’ve finished replacing the covers, we’ll be able to turn on the water heater by turning on the circuit breaker once more. When we first turn on our taps, there will be an irregular flow of water as a consequence of the air trapped inside the water heater, but this is completely normal. In the end, the problem will be remedied within a short amount of time

Recommended Articles

It is possible that we will have some articles that I would want to propose to the readers. Repairing and Maintaining Your Foundation We have discussed the different types of foundations, what a foundation inspection is, and what should be included in a goodfoundation inspection checklist in this article. We might uncover foundation difficulties that cause us to question whether it is safe to live in a house with foundation problems and what is involved in foundation repair. Not only does the repair activity itself have an impact on our wallets, but it also has an impact on our credit scores.

Our team disaggregated these foundation repair expenses and calculated the cost per pier when footings or piers are used to stabilize a foundation that has settled.

Helical piers are preferred for residential real estate items, despite the fact that they are more expensive.

Our crawlspace is flooded, which can be problematic for the entire foundation if the problem persists.

So, what can we do to remedy the situation: What to do when the crawlspace is flooded or there are simplypuddles of water continually standing is described in detail, as is how to remove the water from the crawlspace as fast as possible and how to avoid the problem from occurring in the future.

As I explain in this post, I am hesitant to use lime powder to enhance the air quality in the crawlspace since I would only be using lime powder to avoid the risks associated with raw sewage beneath the house.

We talk about how much it costs to replace a sill plate and how to keep an outside sump pump from freezing because it happened to me once.

One of these methods is the Powerbrace foundation restoration method, which we will look into in this article.

In the articles, it is discussed how animals dig holes around foundations or when they are tunneling beneath concrete, such as beneath a concrete slab or between gaps in concrete footings, for example, In the context of basements, I show how to resolve hydrostatic pressure in the basement, which is a lateral pressure that is the primary cause of a basement wall that is bending, or that can be collapsing in or buckling, in the basement.

  1. While a minor inward slope in a basement wall is permissible, if the degree of bowing reaches a certain point, you must address the problem, which may entail incurring significant and often expensive basement wall repair charges.
  2. ConcreteI will discuss here the technique of concrete lifting or concrete elevating, which may be accomplished using mudjacking or slabjacking, respectively.
  3. FramingThis category contains a number of fascinating articles on the subject of framing.
  4. Many of these issues have an unintended consequence: sagging or sinking flooring.
  5. I also go into great detail about the differences between a mobile home water heater and a standard water heater, which you can find here.
  6. The Titan productportfolio, the Navien range, the Titan N-160reviews, which are the most acclaimed by our readers, and the Rinnai R94LSi are just a few of the water heaters that we have reviewed.
  7. We open a tankless water heater to demonstrate what it looks like on the inside of a tankless water heater, as well as how to protect your water heater from the impacts of hard water.

After the water heater’s useful life has expired, I will discuss the many choices available for disposing of it.

Pest Control is a term that is used to describe the control of pests.

BYM.

My alma mater is Mackenzie University, and I work as an architect and designer.

Additionally, I am a filmmaker and have created a few short films in addition to my architectural work.

HomeQN is a blog where I write about house decorating and building foundations.

The objective is to train homeowners to do as much of their own work as possible, and when this is not feasible, to empower them with knowledge so that they can analyze service estimates and select the best service professionals for their situation.

What size socket to remove a Suburban heating element?

robosmichiganNew MemberJoined: 08/01/2005View ProfileOffline

Have to change out my Electric heating element on my Suburban water heater.What size socket do I need to remove the old one? Looks like a large socket

Carolina CruiserEast TNSenior MemberJoined: 12/07/2006View ProfileGood Sam RV Club MemberOffline

Probably a 1 1/16th


AlbertTamara, the dogs CaseyCody, Living the simple life.God never said Saved by Grace;kept by performance.

Me MargieStanwood, Wa.Full MemberJoined: 05/30/2006View ProfileGood Sam RV Club MemberOffline

Are we talking heating element or anode rod? If it’s the rod then yes, a 1 1/16th like CC suggested or 27mm, which is what I use on ours. A good strong ratchet or breaker bar would also be helpful.


Marv’07 Cardinal 31RKLE’06 F-250 PSD 4X2 S/C, Hijacker, Line-X.

jetcareMobile RV Repairman – Mission, TXSenior MemberJoined: 05/02/2008View ProfileOffline

It is a very large socket.You can get them at Home Depot or Lowes.They ar right next to the heating elements.Matt


2016 F-250 Crewcab 6.2L 4×42012 Palomino Sabre 32′ Travel Trailer

bsinmichHolland, MISenior MemberJoined: 11/18/2000View ProfileOffline

I also had to gring down the edges of mine to get it to fit over the nut of the heating element.The size is in the MH since I don’t have a use for that item any other place.


1999 Damon Challenger 310 Ford

robosmichiganNew MemberJoined: 08/01/2005View ProfileOffline

It is the Heating Element, not the Anode Rod.

The TexanHome. Toquerville, UT. Summer. Cascade, IDSenior MemberJoined: 01/16/2004View ProfileOffline

Don’t get suckered into buying a new “RV water heater heating element”, as there is no such thing. All RV water heaters use a standard heating element that you can buy at HD, Lowe’s or Ace at less than 1/2 the cost your RV dealer will want for a “RV WH element”. Take the old one with you to make sure you have the correct length, +/- an inch. They are around 1450w or 1500w.


BobBetsy – USN Aviation Ret’d ’78LEO Ret’d ’03″Oath Keeper Forever”2005 HR Endeavor 40PRQ, ’11 Silverado LT, Ex Cab 6.2L NHT 4×4, w/2017 Rzr 4-900 riding in 16+’ enclosed trailer in back.Where the wheels are stopped today

What size socket is a water heater element?

Water Heater Socket with a 1-1/2-inch drive. The 6-point opening is designed to accommodate the most common size of electric water heater element, and it fits securely against the hex end of the element so you can apply maximum torque without sliding. 1.5″ Furthermore, how can you unstick a water heater element that has become stuck? In a tiny cup, combine half vinegar and half water to make a solution. To clean between the seam between the heating element and the side of the heating tank, dunk a toothbrush into the solution and brush it between them.

  • In addition to the aforementioned, what size socket do I require for an anode rod?
  • It’s important to utilize a 1/2″ drivesocket, an extension (6″ to 12″), and a long-handled socket wrenchor, better yet, an electric breaker bar if you have one available.
  • Is there a standard for water heater elements?
  • They all have varying power ratings and can operate on either 120 or 240 volts, depending on the model.

What size is a heating element socket?

WaterHeater Socket with a 1-1/2-inch drive. The 6-point opening is designed to accommodate the most common size of electric water heater element, and it fits securely against the hex end of the element so you can apply maximum torque without sliding. 1.5″ In addition to the aforementioned, what size socket do I require for an anode rod? 1-1/16″socket. It’s important to utilize a 1/2″ drivesocket, an extension (6″ to 12″), and a long-handled socket wrenchor, better yet, an electric breaker bar if you have one available.

Second, how can you free a heating element that has been stuck?

  1. Bend the wires of the heating element out of the way
  2. In a tiny cup, combine half vinegar and half water to make a solution
  3. Make an attempt to spin the socket counterclockwise by positioning it above the heating element.

Is it possible to replace a water heater element without having to drain the tank? How to replace the heating element in an electric hotwater heater without having to empty the tank of hot water. If you need to replace the heating element in your electric water heater, you may believe that you must first drain the tank. This is not correct. Please keep in mind that you cannot drain a heater via the high temp pop valve.

How to Remove a Water Heater Element without an Element Wrench? Is It Possible?

Home»Blog» Without the use of an Element Wrench, how do you take out a water heater element? Is That Even Possible? 4022Views Is it feasible to remove the element from a water heater without using an element wrench? Remove a water heater element without using an element wrench if you don’t have one. Changing or replacing a water heater element can be a difficult task, especially if you don’t have an element wrench. The majority of skilled plumbers agreed that we would be unable to turn a stuck element with a standard vice grip or a standard wrench.

  • As a result, we must make certain that we are using the appropriate tool when deleting an element.
  • These goods are hollow steel pipes that may also be used to exactly fit over the socket wrench handle of a space heater.
  • When it comes to heating elements, we offer two different types to choose from.
  • Screw-in water heaters are preferred by professional plumbers, especially for modern water heaters.

However, if you want to convert a screw-in element into a bolt-in element, you may purchase a universal adapter kit from the market. Prior to removing water heater elements, we must evaluate the materials that will be required for the task at hand. In accordance with my findings, we’ll be in need of

  • A garden hose, a screwdriver, a water heater element wrench, a voltage tester, and a replacement heating element with a “O” ring are all required.

Professional plumbers do not recommend utilizing an alternate instrument in place of an element wrench in any situation.

Here’s the step-by-step guide on how to remove a water heater element that needs a replacement.

Check to verify that the circuit breaker at the electrical panel has been switched off before continuing. We may use the voltage tester to see whether any power is getting to our water heater and if so, how much. Remove the water heater element slowly and carefully to ensure that no electricity is being drawn from the system.

Step 2: Attach the garden hose.

We can now begin to connect the garden hose to our water heater, which is a big step forward. At this stage, we are attempting to determine whether or not sediments have clogged our drain valve. During this phase, we will not be required to drain our water tank.

Step 3: Turn off the water supply.

This step necessitates turning off the water supply. It is possible to switch off the water supply by shutting the water input valve, which is often located above our water heaters. Allowing air to enter the tank will allow us to discharge the hot water that has been trapped inside the machine. Finally, we may finish this process by turning on the nearest faucet and turning on the hot water tap.

Step 4: Remove the access panel cover.

It is necessary to remove the cover for the access panel. We will be removing the access panel lid with a screwdriver, which we will demonstrate below. We can also see that the thermostat on our water heater is protected by a plastic cover. We have to be very gentle when removing this. This is also the stage at which we will need to examine the wiring. Is there anything that has been harmed or melted? We must recognize that any broken wires must be replaced as soon as possible in order to avoid any serious consequences.

Step 5: Remove the heating element.

The next step is to take the heating element out of the system. In order to remove this item, we will need to utilize a heating element wrench. Due to the fact that it has a large enough mouth to completely fit the exposed area of the element, this element wrench is the only wrench that can correctly remove this part from the vehicle. Because normal wrenches have the potential to cause harm to this component, professionals do not recommend using an alternative when removing this component. While there is enough water in the tank, we may now begin to lose the element in a counter-clockwise direction while the tank is still full.

Depending on the size of our water tank, this operation might take up to an hour.

Step 6: Clean the new element.

We are now able to clean and wipe the newly installed piece. Ensure that there is no pollution or debris that will be transported to our water heaters is a priority for us. After that, let’s put our brand new “O” ring on our brand new heating element and connect it. In the opinion of skilled plumbers, employing the traditional “O” ring is not a good idea.

The “O” ring has now been secured to the element, which can now be carefully inserted into the tank of our heater and tightened with an element wrench. For the same reason, a regular wrench is not recommended for this technique.

Step 7: Refill the water tank.

The moment has come for us to re-fill our water heater tanks! Turn on the water supply to the heater and then turn off the drain valve to the heater. For the time being, I do not recommend that you turn on the power supply immediately. Before turning on the electricity, we need to make sure that our tank is completely filled. At this time, a half-full container of water might cause harm to the heating components. After that, inspect the freshly installed piece to see whether there is any leakage.

It may also be essential to adjust the “O” ring from time to time.

Step 8: Replace the covers.

The thermostat cover, insulation, and access panel cover may all be replaced when the refilling process is complete. If you have completed the replacement of the covers, we may finally switch on the water heater’s supply by flicking the circuit breaker on our panel. As a result of the presence of air within the water heater, we might see that the water flow is not consistent when we open our taps. This problem will finally resolve itself within a short amount of time. When it comes to eliminating parts, we must make certain that we are just employing the most appropriate and appropriate tools.

  • Each machine is meticulously built with security and individuality in mind.
  • Although an alternate tool may be effective for certain folks, I do not recommend that you use it on your PCs.
  • When it comes to removing a water heater element, I always make sure that I have the proper tools and equipment on available.
  • You may hire these individuals to complete the assignment for you for a very low cost.
  • So, what are your opinions on removing the water heater element without the use of an electric element wrench?
  • Are you looking for a high-quality water heater?

Why You Need a 6-Point Socket to Remove a Water Heater Anode Rod

Anode rod head with sockets is a kind of electrode rod “data-medium-file=” data-large-file=” data-small-file=” title=”cimg4107 – Anode rod head with sockets” description=”cimg4107 – Anode rod head with sockets” src=” h=240″ alt=”Anode rod head with sockets” src=” h=240″ src=” h=240″ src=” h=240″ width: 200px; height: 240px; srcset=”h=240 200w,h=478 400w” h=240 200w,h=478 400w sizes Equals sizing” (max-width: 200px) 100vw and 200px are the maximum values “>Anode rod head with sockets on both ends As previously said, removing a water heater anode rod often needs a great deal of, hmm, persuading.

Because I didn’t have a 1-1/16′′ impact wrench on hand, I used a 12-point socket wrench instead.

Due to its ability to grasp the anode rod bolt head throughout its entire length and on all six sides (as seen in the first photo), the 6-point socket on the right will perform a far better job of preventing the anode rod bolt head from becoming damaged.

What you don’t want is for the wrench to pull the corners off the head before it loosens the thread on the screw.

srcset=” h=240 241w,h=478 482w” sizes=”(max-width: 241px) 100vw, 241px”>Goobered anode rod head srcset=” h=240 241w,h=478 482w” srcset=” h=240 241w,h=478 482w” sizes=”(max-width: 241px) 100v The head of the gobered anode rod is shown from the side “data-medium-file=” data-large-file=” data-small-file=” title=”cimg4108 – Goobered anode rod head – side view” description=”cimg4108 – Goobered anode rod head – side view” src=” h=240″ alt=”Goobered anode rod head – side view” src=” h=240″ alt=”Goobered anode rod head – top view” width: 171px; height: 240px; srcset=” h=240 171w, h=480 342w” srcset=” h=240 171w, h=480 342w” sizes Equals sizing” (max-width: 171px) 171px at 100vw “>Goobered anode rod head seen from the side Despite the fact that the thread on this anode rod was in excellent condition (I’d wrapped it in Teflon tape the previous time I took it out), it was still securely stuck in place.

These photographs demonstrate the damage done to the bolt head by the 12-point socket during the beatdown.

If you don’t already have a hulking bigbreaker bar, you should invest in one; this is not a task for a wimpy 3/4-inch-drive ratchet.

I have yet to come across a satisfactory solution.

src=” h=228″ alt=”Offset Tank – 2009″ src=” h=228″ src=” 320 pixels wide by 228 pixels high srcset=” h=228 320w, h=456 638w” sizes=”(max-width: 320px) 100vw, 320px”>Offset Tank – 2009.

Even after using the nibbling tool to secure the 12-point socket in place, that husky 6-point socket isn’t going to fit into the ridiculously offset hole on the top of the water heater, but that’s just the way fine tuning works.

Leave a Reply

Your email address will not be published.