How to Light a Water Heater Pilot Light
Prev PostNext PostWhen the pilot light on a water heater goes out, it is typically because of a natural fluctuation in gas pressure, which extinguished the flame. The most obvious indicator that a pilot light has gone out is the one that everyone dreads: the water will not heat up properly. In the event of a damaged flame sensor, it’s critical to know how to relight the pilot light on your water heater so you can get the flame going as quickly as possible. This will not only allow you to get your hot showers back, but it will also ensure that no gas is unintentionally discharged into the home.
However, for the vast majority of gas-powered water heaters, you should begin by locating the gas shut-off valve on the water heater, which is generally plainly labeled on the front lower section of the water heater, before proceeding.
- Open the door or cover that provides access to the pilot light. In most cases, this will be positioned under the gas valve
- However, some water heaters will just have an open gap where you can see the pilot light burner instead. Locate the burner within the container using a flashlight or a headlamp. It will be reached by two little gas tubes. You’ll want to keep an eye on it while you’re at work. Turn the gas knob to the “Pilot” position and push and hold the button. This will initiate the flow of gas, allowing you to ignite the flame. Some water heaters feature a separate pilot mode button, which is commonly a red button, which you must push and hold in order to activate it. While keeping the gas pedal depressed, ignite the pilot light. Certain water heaters feature an igniting button that is red or black, while others must be lighted manually with a long lighter
- Some models include a red or black igniting button. Maintaining pressure on the gas knob or button for a full minute after the flame is ignited is critical. Then slowly release it while checking to see if the light is still on. Turn the gas knob to the “On” position and listen for the unmistakable “whump” or whooshing sounds that indicates the main burner has ignited. Enjoy your hot shower when you’ve replaced the lid.
Despite the fact that a single extinguished pilot light is normally caused by a natural fluctuation in gas pressure, recurrent faults suggest a more serious problem with the water heater itself. The most typical problem that causes repeated pilot outages is a filthy or bent thermocouple, which is a thin copper wire and rod that detects the presence of a flame and immediately switches the gas off when it detects a lack of flame detection.
What is a Thermocouple?
A thermocouple is sometimes referred to as a flame sensor in contemporary water heaters because of the way it detects flames. Your thermocouple is most likely twisted, filthy, or damaged if the pilot light continues to go out after you have completed the above-mentioned lighting procedures. For those who find that their pilot light is twisted and not near the burner, they may simply turn off the gas, shift it over, and attempt lighting the pilot again. It may be necessary to clean the water heater gas valve and the main gas line near the heater if this does not solve the problem.
- The burner is typically simple to remove by simply sliding it out.
- If this doesn’t solve the problem, you may get a new thermocouple for less than $15 at any hardware store or home improvement center.
- Rooter Plumbing to help you get hot water back into your home again.
- The use of hot water is simply one component of a great showering experience.
- Previous PostNext Post Previous Post
How to Light the Pilot for a Gas Hot Water Heater
When the water in the tank needs to be heated, tank-type gas water heaters utilize a pilot light to ignite the gas burner, which then heats the water. The cold water flowing from the hot water tap is usually the first sign that your pilot light has gone out, so keep an eye out for it. Even if the equipment is not malfunctioning, a pilot light might go out for a variety of causes, including sudden swings in gas main pressure. If the pilot light on your heater goes out, you may relight it by yourself.
- Find the gas regulator valve on the water heater and turn it on. It is positioned on the exterior of the water heater, near where the gas line enters the device, and it is controlled by a knob on the outside. The gas supply to the pilot burner beneath the hot water tank is controlled by this valve. To turn the valve off, turn the knob all the way to the left. Wait five minutes before continuing. Locate the pilot burner, which is located beneath the natural gas water heater. Remove or unsnap any access cover that is preventing you from getting to the burner. Make use of the flashlight to illuminate the pilot burner
- Turn the knob on the gas regulator valve to “Pilot,” press down on it, and keep it pressed down. The flow of gas to the pilot burner is initiated by pressing this button. To start the pilot burner gas flow on some water heater types, you must push and hold down a separate red button for a period of time. Find a red or black button labeled “Ignition” on the top or side of the gas valve if your heater has a piezoelectric spark pilot igniter built in. To start the pilot, press the button on the control panel. As the igniter ignites, you will hear a click sound. If you must manually ignite your heater, a long-necked barbeque lighter is the most secure type of lighter to use. Light the pilot burner with a lighter flame and turn it on.
After the pilot has been ignited, keep the regulator valve knob firmly depressed for at least one minute. This permits the pilot flame to heat the thermocouple safety sensor, which detects the presence of a live pilot flame, allowing the pilot flame to heat the sensor. Reduce the pressure on the regulator valve knob gradually. When the pilot light continues to glow after you have released the knob, turn the knob to the “On” position. During the ignition of the primary burner, you should hear a muffled “whoomp” sound.
Things You Will Need
Look for a label on your gas water heater that provides particular pilot lighting instructions for the model of water heater you have installed.
- If you smell gas in the vicinity, it is not a good idea to attempt to relight a water heater pilot light (or to do any other maintenance on the device). When you are outside the home, dial 9-1-1.
How To Relight the Pilot Light in Your Gas Hot Water Heater
When the hotwater heater in your home fails, duties such as showering, doing laundry, cleaning dishes, and other household chores come to a grinding halt. If you have a gas-powered hot water heater, it is possible that the pilot light has gone out, which is the root cause of the problem. In most circumstances, if you relight the pilot, you should be able to go back into the air again. In this post, we’ll demonstrate how simple it is to complete the task yourself.
What does the pilot light do?
The pilot light of your gas hot water heater is a tiny, continuously burning flame that serves to start the burner of the appliance. To put it another way, if the pilot light goes out, the unit will be unable to heat water. It is possible for a pilot light to be extinguished for a variety of causes, including something as simple as a short stoppage in the gas line or an air bubble in the gas line. Warning: If you smell gas at any stage throughout the process, leave the area immediately and contact your energy supplier as soon as possible.
Steps to relight the pilot light.
- Remove your foot from the gas pedal. Find the gas shut-off valve on your hot water heater and turn it off. The knob should be labeled in a clear and understandable manner. Turn the switch to the “Off” position and wait 5-10 minutes to ensure that all of the gas has been expelled. Locate the pilot light access point. Most of the time, this will be under the gas valve. To locate the burner and two gas tubes, open the pilot cover (if one is present) and use a flashlight to peer inside the hole to locate the burner and two gas tubes
- Return to the gas valve and turn the knob to the “Pilot” position. By depressing the knob all the way down, you will begin to feed gas to the pilot. There are certain hot water heaters that include a separate pilot button
- If this is the case, press that instead. While maintaining control of the knob or button, reach into the access and ignite the pilot with an extended lighter while still keeping it down. Once the pilot light comes on, keep the knob/button down for about one minute. Release the knob/button carefully after that period of time, and make sure that there is still a flame emanating from the pilot. Return to the gas valve and turn the knob to the “On” position. Typically, a noise will be heard to indicate that the primary burner is lighting
- After giving the heater enough time to restart, replace the access cover and inspect the hot water supply.
What happens if the pilot light goes out again?
The fact that the pilot won’t light or that it keeps going out is a clue that you may be experiencing another problem with your hot water heating system. The most typical issue we encounter is a thermocouple that is twisted, fractured, or filthy (also called a flame sensor). Because the typical service life of a hot water heater is 12-15 years, it may be a wiser investment in some situations to replace the unit rather than spend money fixing your existing unit. if your water heater isn’t producing enough heat, call Reidelt Plumbing Inc.
Our professional plumbers will come out to your home, assess the situation, and provide recommendations on how to restore hot water flow in your home.
- This entry was published on April 30, 2020, under the category Water Heaters.
How Do I Turn My Water Heater On?
Is the water in your home too cold? It’s possible that your water heater has been switched off. It is possible for your water heater to shut down for a variety of reasons, ranging from minor electrical or gas problems to complete system failure. Something as simple as a blast of wind might extinguish the pilot light on your gas water heater if it is powered by gas. It doesn’t matter what the situation is, the first thing you should do before picking up the phone and calling a specialist is attempt to re-ignite your water heater.
Flushing Your Gas or Electric Water Heater: A 6-Step Guide (with Pictures) The majority of the time, unless your water heater requires repair or replacement, you should be able to restore it to working condition on your own.
Find out how to get your gas or electric water heater up and running again in this article.
Common Types of Water Heaters
The method by which you switch on your water heater is determined on the type of water heater you have. The majority of houses have a tank-style water heater, which can be either gas or electric. They operate in a straightforward manner: water is pumped into the tank, and the water is heated by heating devices within the tank. In recent years, tankless water heaters have become increasingly popular. They do not utilize a tank of hot water; instead, they employ superheated coils to heat water on demand, which is why they are frequently referred to as on-demand water heaters.
How to Turn on a Gas Water Heater
If your water heater has a pilot light, it is most likely a gas-powered one. To get it working again, follow these steps:
1. Turn Off the Gas
You should be able to easily identify the gas shut-off valve on your water heater. Select “Off” from the drop-down menu. Keep the door closed for at least five minutes to confirm that the gas has gone.
2. Check for Any Open Valves or Faucets
Close any faucets or valves that may be connected to the tank that are now open. When troubleshooting your water heater, it’s usually a good idea to double-check the valves, since one of them may have been accidentally pushed open.
3. Turn the Cold Water On
Then, switch on the cold-water supply to the water heater to begin heating the water. If you choose to drain it first and start over, that is also OK. It is critical that the tank be completely refilled before turning the engine back on. The fact that you are turning on your water heater when it is empty or when the water level is low might cause it to malfunction. Take advantage of this opportunity to cleanse your system. Flushing your water heater every one to three years might assist to eliminate sediment and extend the life of the appliance.
4. Light the Pilot
Every manufacturer has a separate set of instructions for re-igniting the pilot light, so it’s critical to read and follow the precise instructions that came with your particular item. These instructions are often written on the side of the tank or included in the owner’s handbook. It is critical to note the following: If you sense a strong gas smell at any moment, immediately stop what you’re doing, turn off the main gas valve in your home, and call a professional for assistance. Depending on whether you have an automated or manual system, the following are the fundamental procedures to relighting the pilot lamp:
While holding the pilot igniter button down, hit the spark generator button to activate the generator of light. Continue to hold down the pilot igniter button for 20 to 30 seconds until the pilot igniter turns on. After this period of time, if the water heater pilot does not ignite, you may need to press the spark generator down every 10 seconds until it does so. Most of the time, you can see if it’s lighted through the small glass window where the pilot is located. Once it has been lighted, turn the control knob to the “On” position.
Locate the access point for the pilot light. Push the gas valve to the “Pilot” position and turn it.” Use a long-reach lighter to ignite the pilot while keeping the knob pressed into the cylinder. Continue to press the knob or button for approximately one minute. Slowly release it and return it to the “On” position.” If you listen closely, you should hear a whoosh or click, which indicates that the primary burner has ignited.
After re-igniting the pilot light, let the water tank to heat for at least an hour before checking to see whether it is operational. Additional Related Articles:
- Which is better for my water heater, a question that has been asked for centuries. Learn how to properly drain a water heater
- Learn how much it will cost to replace a water heater
- And much more. Is a Tankless Water Heater a Good Investment? When your water heater isn’t working, you’ll notice these seven tell-tale signs.
How to Turn on an Electric Water Heater
Because electric water heaters do not require a pilot light, the installation process is straightforward. To begin, make certain that the circuit breaker that controls the water heater is turned off. Check for and close any open valves or faucets that you may have discovered. Afterwards, switch on the cold water faucet in order to allow the hot water tank to fill. When it’s completely filled, all you have to do is turn the breaker back on again. Similar to a gas water heater, it may take an hour or more to reach the desired temperature.
What If My Water Heater Still Doesn’t Work?
Electric and gas water heaters can endure for many years if they are properly maintained, but nothing is guaranteed to last forever. If you’ve attempted to switch on your water heater and ignite the pilot light without success, consult with a professional to determine whether the unit needs to be repaired or completely replaced. Because we are spending more time at home than ever before, it is critical to be prepared for unexpected home repairs with a plan from HomeServe. The knowledge that you can easily call our 24-hour repair hotline in the event of a covered breakdown provides you more peace of mind.
How to light a gas water heater
If your water heater is not heating up, it is possible that the pilot light has gone out. No matter what sort of water heater you have, the process of lighting it is straightforward. The majority of contemporary versions of gas water heaters are equipped with a straightforward ignition switch. The water heater is turned on in a matter of seconds, no trouble. If you’ve moved into an older home, on the other hand, it’s possible that your water heater is the type that requires manual activation.
Do you have a manual water heater?
There is a straightforward technique to determine if your gas water heater is automated or manual. Take a look at the box that protrudes from the side of the water heater and has two distinct dials. Automatic vehicles will feature a little ignition button adjacent to the large On/Off/Pilot dial, indicating that it is an automatic. If it is a manual, there will be no button to press. The On/Off/Pilot dial is normally located on the top of the box, whereas the temperature dial is typically located on the side of the box, as shown.
Taylor Martin is a contributor to CNET.
How to light an automatic water heater
The first step is to switch off the gas by looking for the knob labeled On/Off/Pilot on the control panel. You’ll want to move the knob past thePilot position and into theOff position. Allow for a five-minute dissipation of any built-up gas that may be present in the system. It’s time to start the lighting procedure at this point. Turn the water heat dial to Low and the On/Off/Pilot dial to Pilot to complete the process. Then, while simultaneously pressing the igniter button and turning the On/Off/Pilot dial down, turn the On/Off/Pilot dial up.
You should hear a “whoosh” sound as soon as the gas is turned on.
If it is lighted, conclude by closing the door and turning the dial fromPilottoOn, as well as changing the water temperature dial from Low to the temperature you like. To avoid gas accumulation, you must restart the process immediately if the pilot light is not lighted.
How to light a manual water heater
To fire this style of water heater, I recommend using a long barbeque lighter like this one. In any other case, getting in touch with the pilot will be difficult. To begin, remove the plate that is located beneath the dial-equipped box on the side of the water heater. There may also be an inner plate that you will need to shift to the side in order to complete the installation. Following that, you should notice a pipe or pipes heading to a burner. Then, in the box labeledOn/Off/PilotpastPilot, turn the knob to the Off position until it is completely off.
- Turn the water temperature dial to the lowest setting and the On/Off/Pilot dial to the Pilot position.
- Hold the barbeque lighter over the end of the pipe near the burner for a few seconds.
- Continue to press thePilotdial downward for about 30 seconds, after which move the dial fromPilottoOn.
- Important: If the burner does not come to life within a few seconds, repeat the operation until the burner does.
- Is the energy efficiency of your home high?
- CNET’s Guide to Smart Livingis a one-stop shop for tips, techniques, and how-to guides that can help you live a more intelligent life.
How to Light a Water Heater’s Pilot Light (With Pictures)
With 23 years of experience in the HVAC sector, Dan has gained knowledge in a variety of areas, including installation, service, sales, and distribution. Some individuals may think that lighting the pilot on a hot water tank is an easy chore, but as a home service provider for over 15 years, I can assure you that I’ve made more than a few dollars executing this task for others. Despite the fact that many modern gas-burning appliances have converted over to hot surface or electronic ignition, there are still a significant number of standing pilot systems being made and used today.
It will be explained in detail in the following stages how to light your pilot, what to watch for when doing so, and a few other techniques you may use to get the fire started.
- 15 years of experience in HVAC installation and service
- 5 years of experience as a home improvement contractor
- Product safety, performance, and certification testing experience spanning more than two years
- EPAOSHA certification. Electrical theory, thermodynamics, and refrigeration coursework have been completed
This is an illustration of what a sealed combustion chamber on this sort of device may look like. It’s your looking glass, which is represented by this small square on the panel. Take note of the differences between this sort of control module and the earlier tank-style control module. In addition to being a control, the little knob on top serves as a button. View from above in order to notice the electrical spark button to the left.
Lighting a Sealed Combustion Pilot
We’ll start with a hot water tank system that is more contemporary and uses sealed combustion technology. With a sealed combustion chamber, there is no need to enter the burner assembly, and you should avoid doing so if at all possible. There is a looking glass in the access panel that you may use to visually verify if the pilot is lit.
Everything you need to light this pilot is mounted directly to the burner control module. This access is bolted shut for a purpose, and it should only be accessible by individuals who are properly trained and licensed.
- Set the gas control knob on the top of the stove to the “pilot” position. To enable gas to flow, press and hold down the control knob itself for many seconds. Press and hold the electronic spark button, which is placed on or attached to your control module, until you hear it click. If there is a little amount of air in the line and it takes a few seconds to “bleed out,” you may need to click it a few times before the pilot is lighted. Continue to hold down the knob until the pilot has heated the thermocouple enough for it to be able to confirm ignition with the thermostat in the control module by visual confirmation. If the thermocouple does not heat up sufficiently, the pilot will be forced to return to the aircraft. Remove your finger from the control knob and visually check that the pilot is still glowing. To turn on the gas, turn the gas control knob to the “on” position. If the pilot was left out long enough for the water temperature to decrease, the burners should begin to operate within seconds of the pilot being turned off. If the water has not cooled, it is possible that there will be no need for the burners to be turned on. Be prepared for it to not start up immediately
- This is normal.
You are in the correct position if the notch is aligned with the button and the “pilot” is aligned with the indicator. The following is an illustration of what an open combustion burner assembly can look like. I’ve taken the two panels off so you can see what they look like on the inside. It is the copper line you can see in this shot that connects to the thermocouple, and the aluminum tubing that connects to the orifice where you will insert your lighter. Inside the room, the two come face to face.
Lighting an Open Combustion Pilot
Unlike the sealed combustion tank, you will be required to provide your own flame to light the pilot, rather than relying on an electronic ignition to do so for you. This process is very similar to the sealed combustion tank, with the exception that you will be required to provide your own flame to light the pilot yourself.
- The gas control knob should be set to pilot mode so that the notch in the dial corresponds to the button that controls the gas supply. If you do this, you’ll be able to press the button all the way down when it’s necessary
- Remove the panels from the burner compartments. Both should be quite simple to remove by raising up and pulling out. Place your preferred flame source (lighter, match, or other similar item) into the chamber such that the flame is directly beneath the aperture of the pilot supply line and ignite the flame. NOTE: I prefer to do three and then four. Despite the fact that the two stages can be exchanged, I believe it is better to introduce the flame before providing gas in order to minimize even the slightest possibility of gas buildup. I prefer to err on the side of caution, so I press and hold down the pilot gas supply button for many seconds before visually confirming that the pilot has been ignited. Keep the pilot gas supply button depressed for about 30-45 seconds to heat the thermocouple if this is the case. Release the button and visually check that the pilot light has not been extinguished. Assuming the pilot light remained on, turn the gas control knob to the “on” position.
Again, depending on your conditions, the water heater’s burners may or may not turn on straight immediately, so be patient.
Things You Can Use to Light a Pilot Light
- A long, thin candle
- A long, thin lighter
- Long, thin matches
- Short matches with a Hemostatic Clamp
- A long, thin candle
Don’t Have a Lighter or Matches?
Lighting a long, thin candle on the stove and utilizing it to light the pilot light may be an option. When doing this, place a piece of tin foil behind the pilot to prevent wax from spilling onto the bottom of the chamber.
A Quick Water Heater Inspection You Can Do
- Check for moisture and corrosion in the surrounding area and at the bottom of the unit (a.k.a. blisters). This might be a signal to be ready for a new tank
- For example, Check to ensure that your T P valve is operational. Feel the tank in your hands. Is it comfortable? If this is the case, you may want to consider adding an additional layer of insulation. Check the operation of your thermostat control. You may accomplish this by reducing the heat down to the lowest setting and turning off the burners, if any are already operating. It is expected that the burners will shut down at this point and that they will re-ignite within seconds of turning the burners back on. If not, your control may be inadequate, and you should seek professional assistance. Final question: “When was the last time I cleansed my water heater?” You may wish to ask yourself this question. This is something that should be done at least once a year.
To the best of the author’s knowledge, the information in this article is accurate and complete. Content is provided solely for informative and entertainment reasons and should not be relied upon as a substitute for personal counsel or professional guidance in commercial, financial, legal, or technical problems, unless otherwise specified. Dan Reed was born in the year 2012. Dan Reed (author) wrote the following on April 22, 2012: Thank you so much, Mmargie. People who have never done it before may be nervous, but I always spend a significant amount of time thinking about my directions and selecting themes that are safe for anybody to try if the instructions are followed.
I’ve always been apprehensive about using gas appliances.
lolI feel a little better after reading the particular instructions on your site, despite the fact that I do not currently have any gas appliances.
7 Reasons Your Water Heater Pilot Light Keeps Going Out
There is nothing more inconvenient than stepping into a frigid shower to begin a chilly day. It’s possible that you’ve recently found that the pilot light is constantly going out. Thousands of consumers are dissatisfied with their water heaters, which fail to function properly only a few months after installation. Is it usual for your water heater to go out on you in the middle of the night? No! Your heater should be able to easily reach the 10-year milestone without experiencing any serious problems.
Take a look at these beautiful water heaters in Phoenix.
What Is The Pilot Light?
The Pilot Light is the heart of your water heater, and it controls the flow of water.
Essentially, it is a little blue flame that produces heat by burning petroleum gas. There would be no heat and, hence, no warm water if this flame were not present.
So, What Are The Reasons Your Water Pilot Light Keeps Going Out?
Not only will we identify the potential issues, but we will also provide you with solutions to those issues. Please take notice of the following: Check to see whether your water heater is still covered by the manufacturer’s warranty. If this is the case, it should be returned to the supplier or manufacturer for repairs or complete replacement. Precautionary measure: To begin, shut off the main gas supply valve to prevent potentially fatal gas leaks. Wait 5 minutes for the heat and gas to dissipate before continuing.
1. An Unclean Pilot Tube
It’s a problem that practically all water heaters have at some point. Please don’t be concerned, your heater is in perfect working order. It’s simply a buildup of dirt. The Pilot tube is responsible for supplying gas to the pilot light in order for it to burn. if the tube becomes blocked with dirt or other particles, the flame will go out. It is possible that the tube is partially blocked and only supplying a little amount of gas for combustion—which explains why your pilot light keeps going out.
To gently clear the tube, use a thin needle to poke it with.
You must be patient during this process.
Place the container back where it belongs and turn on your water heater.
2. A Dirty Thermocouple
In the case of a water heater, the thermocouple serves as its brain. It is in charge of shutting down the gas valve when it detects that the pilot light has gone out. Because the pilot light produces an electric current, the thermocouple is activated when this current is present. It serves as a safety measure, preventing gas leaks from occurring. As a result, a filthy thermocouple might be the source of your water pilot’s inability to function properly. When a coating of filth and dust accumulates on the surface of a thermocouple, the electric current cannot reach it.
On a chilly Monday morning, there is no hot water.
To begin, shut off the main gas supply valve and allow the thermocouple to cool before proceeding.
3. A Kinked Thermocouple
As soon as you’ve finished cleaning, double-check the location of the thermocouple. Also, look to see whether it’s a little bent. The thermocouple must be placed close to the pilot light in order for it to receive heat and activate the gas valve. As a result of being too far away, heat will not be received and an electric current will not be generated. The thermocouple will determine that the pilot light has been turned out and will seal the valve, cutting off the gas supply to the house. The answer is as follows: First, turn off the gas and turn off your heater, and then wait for the thermocouple to cool down before proceeding.
You’ll have to bend or straighten the thermocouple manually to get it back into position. To be effective, the blue flame must be placed close enough to the pilot light so it contacts or wraps around the blue flame.
4. A Broken Thermocouple
So, you’ve cleaned and straightened your thermocouple, but your water pilot continues to fail despite all of your efforts. You should be prepared to accept the possibility that your thermocouple is faulty at this point. Perform a diagnostic test with a multimeter on your thermocouple first, though, before you give up on it. If the voltage delivered by your thermocouple is significantly less than 20MV, then the device is almost certainly damaged and should be replaced immediately. The Solution: If the multimeter reading is near to, but not exactly at, 20MV, you can adjust the thermocouple closer to the pilot light to save energy.
5. Flex Tube Issues
Flexible tube is a long tube that links the gas controller to the burner, which contains the pilot light, thermocouple, and other components. If the flex tube is broken or blocked, the gas will not be provided to the burner for combustion to take place. Flex tube failures, on the other hand, are not as prevalent as thermocouple failures. This is why you must first inspect and ensure that your thermocouple is in excellent working order before turning your attention to the flex tube. The Solution is as follows: Straighten any kinks in the flex tubing that have formed.
Leaks in the gas line will lower the amount of gas that reaches the burner.
6. A Faulty Main Control Valve
It’s possible that you’ll never run into this situation again. We recommend that you examine the pilot tube, thermocouple, and flex tube before attempting to modify or repair this piece of equipment. The Main Control Valve Unit has a very low failure rate. However, don’t count it out just yet; it’s possible that it’s the source of your water pilot’s incessant failure. Main Control Valve: This valve is in charge of regulating the gas and water pressures of the water heater. Your water heater’s heart and soul is the thermostat.
When the gas is ignited, the main valve is fully opened, allowing for a consistent stream of gas to be provided.
The following are signs of a defective main control valve:
- A malfunctioning pilot button that does not illuminate after being pressed
- A malfunctioning control knob
- When the water temperature exceeds the stated range, you will feel extremely hot water.
The solution: There is no way around a defective main control valve in this situation. However, despite the fact that there are specialists who say they can fix this, manufacturers highly advise against it. It is recommended that you replace the item to prevent incurring more expenditures and causing damage to other components of your water heater.
7. Poor Electrical Wiring
When it comes to electric water heaters, this is generally a concern. The fact that you should always engage a professional to install your water heater is one of the main reasons for this.
If your water heater suddenly stops working, this is the first indication of a defective electrical system. The Solution: Turn off your water heater as soon as possible and contact a professional. Please do not tamper with the electrical wiring system.
Our Final Word
If all of your methods fail and your pilot light continues to go out, it’s time to call in the heavy guns (the professionals). We’re aware. We’re aware. The services of technicians are not cheap, but at the very least you will have greater confidence in the repairs. In addition to that, we are all aware of the dangers associated with electricity and natural gas. Your safety is of the utmost importance. Did you find this information useful? Check out Why Are Trane HVAC Units So Popular? for more information.
Light Your Hot Water Heater Pilot Light in 5 Easy Steps
Posted at 12:00hinPlumbing Services on February 12, 2019 There are a variety of reasons why your hot water heater’s pilot light may go out. However, while the absence of a pilot light may signal a problem with the heater itself, a hot water heater pilot light can also go out for a variety of other causes, such as oscillations in the gas pressure. If your pilot light is out, you will most likely see cold water flowing out of your hot water valves when you turn on the water. The good news is that you can easily re-ignite your hot water heater pilot light by following these five simple steps:
1. Turn Off the Gas
The first thing you should do is make certain that the gas has been turned off completely. Locate the gas regulator valve in order to accomplish this. On the outside of your water heater, around the point where the main gas line enters the heater, you’ll often find this valve. Allow at least five minutes to pass after turning this valve to the “off” position to allow any leftover gas to disperse.
2. Where is The Pilot Light on Hot Water Heater?
This section will most likely necessitate the use of a flashlight. Most of the time, the pilot light for your hot water heater may be found beneath the water tank on your device. It is possible that you may need to remove an access panel in order to get to it. Some newer versions may have the pilot light hidden behind a glass panel, which is a nice touch. In appearance, the pilot light’s housing should be in the shape of a little silver tube. You will need to hire a plumber to diagnose any additional issues you may be experiencing with your water heater if there is already a flame burning at the end of this tube when the pilot light is turned on.
3. Check for any Gas Leaks
Ensure that there are no gas leaks or residual gas before proceeding any further. Igniting a flame in the vicinity of a gas leak can be extremely hazardous to your health and the safety of your property. Relighting your hot water heater pilot light should only be done if you are certain that no gas is leaking from the device. You may confirm this by doing a basic smell test as follows: Take a few deep breaths while standing near to your water heater and smelling the air. Despite the fact that natural gas is odorless, gas companies use an additive called mercaptan to guarantee that it may be discovered in the event of a leak.
If you don’t detect any rotten eggs-like odors in the air surrounding your water heater, step closer and sniff any of the valves, pipes, or connection points in the vicinity of the unit.
Immediately leave the house if you detect even a faint whiff of gas and contact your plumber, who will be able to advise you on what steps to do next.
When you leave the house, avoid turning on or off any lights since this might cause sparks that could ignite the gas.
Always leave the house before phoning someone or sending a text message. Natural gas that is leaking can make you sick, and spending any further time near a gas leak increases your chances of accidently inhaling or igniting the leaking gas.
4. Ignite your Hot Water Heater Pilot Light
It is safe to restart your hot water heater pilot light once you have determined that there are no leaks in your water heater equipment. To accomplish this, set the regulator valve to “pilot” and press and hold it down for a few seconds. Depending on the model, you may be required to press a second red button to regulate the flow of gas to the pilot light. If your machine includes a dedicated pilot button, it will most likely be red and labeled “pilot.” Check the front of your unit for instructions that may assist you in locating all of the valves and buttons necessary to re-ignite your hot water heater’s pilot light, if there are any.
When it comes to newer models, the “ignition” button on your water heater should be either black or red in color.
As this occurs, you should hear a clicking sound.
The safest method for accomplishing this is to use a long-nosed lighter, such as those used to ignite barbecue grills.
5. Make Sure the Flame Stays Lit, and Your Heater is Working.
Maintain pressure on the regulator valve for at least a minute after the pilot light has been ignited. The thermocouple sensor will be able to re-heat as a result of this. This sensor detects whether your water heater’s pilot light has gone out and will shut it down if the water becomes too cold to handle. Allow for a minute before carefully releasing the regulator valve and checking to see whether the pilot light continues to burn. If this is the case, switch the regulator valve to the “on” position.
Once this is accomplished, your pilot light should be operational.
Dealing with natural gas may be a frightening experience. It is possible, however, to safely rekindle your hot water heater pilot light whenever you need to if you follow these simple instructions. It’s always possible to call Benjamin Franklin Plumbing for skilled, timely, and locally-based assistance if you are still unclear of what you are doing, cannot figure out how your specific model works, or simply prefer to have a professional handle the situation instead. BFP Duncanville provides plumbing services to the Southwest Dallas communities of Cedar Hill, Dallas, DeSoto,Duncanville, Glenn Heights, Grand Prairie, Maypearl and Midlothian as well as the towns of Oak Cliff and Ovilla.
In addition to emergency plumbing repair, the company offers a variety of other plumbing services, including faucet repair, drain services, toilet repair, plumbing fixture installations, tub and shower installations, kitchen sink repair, faucet installation, water heater repair/replacement, and garbage disposal replacement, among other things.
For further information or to make an appointment, please contact us at (972) 263-5010.
Why Your Pilot Light Keeps Going Out & How To Fix [With Pictures]
That darn pilot light just won’t stay turned on! Moreover, it is causing all of your plans for today to be derailed. Nothing compares to the sensation of taking a hot water shower. However, there are times when this does not occur. After all, there are worse things than having a very cold bath, should we say? The one thing that everyone despises is a lack of running water. This may be incredibly inconvenient – not only for showering, but also for all of the other duties that require hot water to be completed successfully.
You don’t have to put your day on wait because your pilot light isn’t working properly.
However, if you discover that your water heater is leaking water and that this is the root of your water problem, read our guide on what to do when your water heater is leaking water!
What’s A Pilot Light?
An electronic device that maintains a continually burning flame is known as a pilot light. Basically, the goal of this section is to light the burner. How? When you switch on your appliance, gas is released from the main burner, and the pilot light flame ignites the gas, so supplying heat to the room. With each degree of heat generated by the main burner, the air or water contained within your appliance is heated and then disseminated as needed around your residence or place of business
Appliances With Pilot Lights
Water heaters, older furnaces, and boilers are more likely to have a pilot light than other types of appliances. You may also discover that your gas fireplace has a pilot light, which is a good thing. Learn how to switch on the pilot light on your gas fireplace by visiting this page. Pilot lights have been gradually being phased out in favor of hot surface igniters or spark igniters in more recent years. pilot light for a water heater The pilotflame ignites the gas, which generates heat for your house or place of work.
Also, if you are experiencing no heat, check to see whether the pilot light on your furnace or boiler has gone out.
Water Heater Pilot Light: Where Is It And What Does It Do?
A little access panel, located just underneath the thermostat, may be found at the very bottom of your gas water heater. The pilot light for the gas water heater is located within the access panel. There will be a gas panel where you may check to see if the pilot flame has been ignited. The pilot light on your water heater is a little flame that is used to ignite the gas burner in the water heater. This is required for the purpose of heating the water that will be dispersed around your home. If you are experiencing no hot water and have attempted to relight your pilot light without success, you will require water heater repair.
The pilot light on the water heater keeps going out. Warning! Remove the burner and pilot from the interior of your water heater at your own risk. This photograph was shot by a water heater professional for the purpose of giving a demonstration on the use of pilot lights.
What Makes Your Water Heater Pilot LightGo Out
Thermocouple on the water heater is faulty. The thermocouple is responsible for detecting whether your pilot light is on. This copper rod serves as a safety precaution, preventing the heater’s gas supply from being turned off if the pilot light on the water heater goes out. The natural wear and tear of a thermocouple can cause it to get twisted out of place, to malfunction, to become broken, to become covered in dirt, or to accumulate carbon deposits. When one or more of these conditions occurs, the thermocouple will be unable to reliably detect the pilot light and will subsequently shut down the heating system.
Strong Breeze Can Blow Out Pilot Light
In some cases, such as when there is heavy wind or a nearby draft, your pilot light may be extinguished. Unless your pilot light has simply been out, you should have little trouble re-igniting it and keeping the flame burning.
Kink in the Flex Tube
The fuel is delivered to the gas controller by flexible tubes. Gas will not flow through the tube if there is a kink or twist, which can also lead to pilot light difficulties.
Filthy Pilot Light OpeningCan MakePilot Light Keeps Going Out
If the pilot’s mouth is clogged with muck and debris, it will be virtually hard for it to maintain a flame. It will only keep a modest flame that will be readily extinguished if it does catch fire. Your pilot light will not stay lit if your pilot orifice is clogged with debris.
How Do I Re-Light My Gas Water Heater Pilot Light?
The pilot light on the water heater is not lighted.
Step 1: Thoroughly Read Gas Water Heater Manual
To have a better knowledge of where each component of your water heater is situated, consult your water heater’s instruction manual.
Step 2: Turn Down Thermostat
To have a better knowledge of where each component of your water heater is situated, consult your water heater handbook.
Step 3: Turn OFF Gas
The gas valve for the water heater Locate the gas shut-off valve and turn it all the way to the “Off” position. The gas shut off valve is positioned on the gas line near the base of your water heater, near the base of your water heater. Before proceeding on to the next stage, you must wait at least 5 minutes to guarantee that all of the gas has dissipated completely.
Step 4: After 5 Minutes, Turn The Gas Control Valve Setting On Water Heater To “Pilot”
Turn the gas control valve, which is situated on the water heater, to the “Pilot” position. The word “Pilot” should be in the center of the image.
Step 5: HoldDownthe Reset Button
Keep the water heater reset button depressed. After that, press and hold the reset button. This is a button that is often red in color and is situated to the left of the gas control valve. Keep your finger on this button. To be on the safe side, use the instructions to identify each component.
Step 6: While Holding Down The Reset Button, Press TheIgniter
Keep the water heater’s igniter down. The igniter is located to the right of the gas control valve. While continuing to keep the reset button down, press the igniter button on your keyboard. Click on the water heater’s gas window until you see a blue flame appear in the glass.
Step 7: Continue To Hold Down The Reset Button For 20-30 Seconds.
Following the sighting of a flame and the removal of your finger from the igniter, you must continue to press the reset button. Continue to hold the button down for another 20-30 seconds.
Step 8: Turn The Gas Control Valve To The “On” Setting
On the water heater, there is a gas control valve.
The gas control valve may now be turned back to its “On” position, as the pilot light has been ignited by the flame. The word “on” should be in the middle slot at this point.
Step 9: Turn The Thermostat Up
Increase the temperature of the water heater. Now is the time to dial up the heat in order to get that hot water flowing again!
Step 10: Enjoy Your Warm Water, Or Ask For Help!
If you try to relight the pilot light and it does not stay lit, you may want the services of a professional to assist you with your water heater repair.
But What If You Don’t Have A Manual Igniter?
After that, remove the access panel that is located beneath the water heater thermostat and discard it. You can use a wrench to help you.
After 5 minutes, Turn Gas Control Valve To “Pilot”
Now, set the gas shutoff valve to the “Pilot” position.
Next, Hold Gas Control Valve Down And Ignite Pilot With A Lighter
Keep the gas knob pressed down as you ignite the pilot using a long lighter, similar to a BBQ skewer. If your gas water heater, on the other hand, has an igniting button, use it instead.
Once TheFlame Is Lit,Turn Gas Control Valve to “On”
As soon as the pilot light is lighted, you may remove the reset button and turn the gas knob to the “On” position, which will take around 30 seconds. You should be able to hear the main burner turn on at this point. Your pilot light should now be able to maintain a flame, and hot water should be flowing again!
Furnace Pilot Light: Where It Is And What Does It Do?
Old furnaces rely heavily on the pilot light to generate heat, which is why it is so crucial to keep the pilot light on. When the gas valve is opened, the flame will continue to burn constantly, igniting the gas. The heat generated by this process then heats the air that is drawn into your furnace, which is then dispersed throughout your house. If your furnace’s pilot light is out, you may notice that it is spewing chilly air into the house. The failure of the pilot light is one of several probable causes of your furnace’s inability to switch on.
You may find the pilot light by following the gas line into your furnace and looking for it there.
From there, you should be able to see a short tube that runs from the gas valve to the burner itself.
Why Furnace Pilot Light keeps going out
There are a variety of reasons why the pilot flame on your furnace continues flickering out of control. Let’s get started!
Faulty Thermocouple Triggers Pilot Light to Go Out
It is meant to shut off the gas valve if the pilot light goes out, and it is used in conjunction with a thermocouple. Thermocouples can be damaged or worn out over time. If the thermocouple is incorrectly positioned or malfunctioning, the gas valve may be incorrectly shut off, as well as preventing the pilot light from keeping lit.
Dirty Thermocouple Makes Pilot Light Keeps Going Out
A filthy thermocouple may cause the safety mechanism to mistakenly trigger, causing the ignition to be turned off. The thermocouple has the potential to accidentally shut off the gas valve and extinguish the blazing flame.
Filthy Pilot Port/Orifice
Examine the flame. If the flame is becoming orange, contact an HVAC professional immediately. If you light your pilot and the flame is yellow, this indicates that your pilot opening is filthy and is preventing your pilot light from keeping lit for long periods of time. A buildup of dirt in the pilot light port might prevent the flame from fully enveloping the thermocouple, which can result in a faulty ignition.
As a result, the safety system is activated, which results in the gas being turned off. This is a fairly typical cause of why your pilot light keeps going out, and it is easy to diagnose.
Bad Gas Regulator
If you have gas appliances in your house, you will also have a gas regulator outside of your home to regulate the flow of gas into your home. Your furnace may not receive enough gas to keep its pilot light lit if your gas regulator isn’t functioning correctly. There is a good chance that you have a defective gas regulator if the pilot light is out in more than one home appliance, such as your water heater.
Bad Flue Venting Could Blow Out Pilot Light
Excess wind might enter via the openings in your flue pipe if it is loose, broken, or not correctly attached to the furnace. This would extinguish the pilot light flame.
A Strong Draft
There’s always the potential that a powerful draft knocked out your pilot light’s flame and caused it to go out.
How To Re-Light A Furnace Pilot Light?
The first and most crucial step is to locate the owner’s manual for your heater. The handbook will assist you in gaining a better grasp of the internal workings of your individual appliance.
Step 2: Identify Pilot Light
Find the location of the pilot light in your furnace by consulting the owner’s handbook. In order to get access to the furnace, you will need to remove the front of the furnace.
Step 3: Turn OFF Gas
After that, locate the gas valve and shut it down completely. A tiny valve located towards the bottom of the furnace is standard on most models. In general, there are three settings for the gas valve: “ON,” “OFF,” and “PILOT.” Make sure the valve is in the “OFF” position by turning it clockwise. It is critical that you wait for at least 5 minutes after the previous step to ensure that all gas has been expelled from the pipes before proceeding. A disaster might occur if this is not done.
Step 4: WAIT 5 Minutes, then Turn Gas to “Pilot”
Immediately after waiting 5 minutes, switch the gas valve to the “PILOT” position. It is vital that all of the gas has dissipated before switching the gas position to the pilot position. A few of minutes might be the difference between a peaceful society and a disasterous one. Keep in mind that gas is quite explosive!
Step 5: Hold Reset Button
After that, hold down the reset button. However, if you are having difficulty locating the reset button, your furnace’s owner’s handbook should be able to point you in the appropriate place.
Step 6: Press Igniter While Holding Reset Button
Holding the reset button down for a second or two will allow you to activate the igniter and light the flame. Once the flame has been ignited, remove the igniter and continue to hold down the reset button until the flame has been extinguished. Keep the reset button pushed for 20-30 seconds to complete the process. To light the pilot when you do not have a manual igniter, you can use a BBQ lighter or a match. furnace with a pilot light
Step 7: Turn Gas to “ON” position
Restore the pilot light by turning the gas control valve back to its “ON” position once it has been re-ignited. Right now, you should be able to keep your house warm!
Step 8: If you Aren’t comfortable yet, call a pro!
If, despite doing the necessary measures, you are still unable to keep your pilot light lit, contact an HVAC professional for furnace repair.
Boiler Pilot Light: Where It Is And What Does It Do?
The pilot light in your boiler is vital for the boiler to function properly and generate heat. It is necessary for the pilot to burn constantly in order for it to ignite the gas when the gas valve is opened. When this occurs, your boiler starts heating the water, which is subsequently dispersed throughout your house to provide warmth.
If your pilot light goes out, your boiler and central heating will not be able to operate properly. The pilot light is placed within your boiler, on the other side of the valve from the gas valve. The boiler handbook should help you have a better knowledge of the location of each component.
Why Boiler Pilot Light Goes Out
A malfunctioning, misaligned, filthy, or damaged thermocouple is frequently the source of your pilot light’s failure to illuminate properly. It is the thermocouple that keeps the gas valve from opening if the pilot light is not lit. Your pilot light may not function properly if there is an issue with your thermocouple, or if it is just coated with dirt and debris.
Dirty Pilot Opening
When you turn on your furnace pilot light and find a yellow flame, this indicates that your pilot light is unclean and is causing your furnace pilot light to constantly turning out. If dirt accumulates in the pilot light port, it may prevent the pilot light from completely enveloping the thermocouple with the flame it produces. This causes the thermocouple safety system to be incorrectly activated, resulting in the gas being turned off and the heat being turned off.
Weak Gas Regulator Can Make Pilot Light Keeps Going Out
If you have gas appliances in your home, you will have a gas regulator outside your home. The failure of your gas regulator may result in your furnace not receiving enough gas to keep its pilot light lit. In the event that you observe pilot light issues on more than one device, such as your water heater, it is possible that your gas regulator is broken or weak.
A Strong Draft
A strong airflow has the potential to completely extinguish your pilot light.
How To Re-Light Boiler Pilot Light
Make sure you are familiar with the components of your boiler by reading the instruction manual thoroughly. It is common for the owner’s handbook to contain instructions for re-igniting the pilot light.
Step 2: Shut OFF Boiler
Starting with shutting off the boiler is always a good idea.
Step 3. Shut OFF Gas
Locate the gas valve and turn it to the “OFF” position.
Step 4. Wait 10 Minutes
Continue to check the pipes for around 10 minutes to ensure there is no residual gas.
Step 5. Open Boiler and Locate Pilot Light
After a short period of time, you can turn on the boiler. To obtain access to the pilot light, remove the access panel from the wall. Typically, this panel is positioned next to the gas control knob box, which is where it gets its name. Sometimes you may simply lift the panel up, but other times it may be screwed to the wall or ceiling.
Step 6. Turn Gas to “Pilot”
Now, set the gas control valve to the “Pilot” position on the pilot valve.
Step 7. Hold Reset Button, Then Click Igniter
Next, press and hold the reset button for a few seconds. While still holding down the reset button, press and hold the igniter button until you see a flame appear. It is necessary to press the reset button for an additional 20-30 seconds after the flame is ignited to ensure that it is fully functional.
Step 8. Turn Gas Control Valve To “On” Setting
Restore the pilot light by turning the gas control valve back to its “ON” position once it has been re-ignited. Right now, you should be able to keep your house warm!
Step 9. Relax in Comfort
How did things turn out? If not, when will you get your home warm and comfortable? If your pilot light has been struggling to keep a flame, or if you are still unclear how to fire your pilot light, boiler repair is simply a phone call away!
Now that you don’t have to struggle with a cold house anymore, you may turn to a licensed professional with your queries and concerns. To arrange a boiler repair, call or go online to this page. With the help of superTech HVAC Services, you can relight your pilot light in no time.
How Do I Prevent My Pilot Light From Going Out?
Keeping your water heater, furnace, and boiler in good working order can keep those annoying pilot lights from going out on you. An experienced technician will do a maintenance check on the pilot light and thermocouple, as well as clean them both, to ensure that they operate at peak efficiency. Depending on the appliance, a professional will also check all of the connected pipes and wiring, the flue venting, and all other functional aspects of the appliance to verify that each portion is running at peak efficiency.
Maintaining your furnace, water heater, and boiler on a regular basis is essential to ensuring that your heat or hot water never runs out!
Soak Up The Warmth!
That’s all there is to it! A basic description of how to relight your pilot light, as well as the most typical causes for your pilot light to go out is provided. We all know that having no heat or hot water in your house is the worst feeling in the world! The best course of action if you’re having difficulties keeping your pilot light lit or are still unclear about the process is to call a professional. If you are experiencing any pilot light issues, please don’t hesitate to contact us at (443) 219-7798 or make an appointment onlinehere.