How To Tell If Pilot Light Is Out On Water Heater

How to Light a Water Heater Pilot Light

Prev PostNext PostWhen the pilot light on a water heater goes out, it is typically because of a natural fluctuation in gas pressure, which extinguished the flame. The most obvious indicator that a pilot light has gone out is the one that everyone dreads: the water will not heat up properly. In the event of a damaged flame sensor, it’s critical to know how to relight the pilot light on your water heater so you can get the flame going as quickly as possible. This will not only allow you to get your hot showers back, but it will also ensure that no gas is unintentionally discharged into the home.

However, for the vast majority of gas-powered water heaters, you should begin by locating the gas shut-off valve on the water heater, which is generally plainly labeled on the front lower section of the water heater, before proceeding.

  1. Open the door or cover that provides access to the pilot light. In most cases, this will be positioned under the gas valve
  2. However, some water heaters will just have an open gap where you can see the pilot light burner instead. Locate the burner within the container using a flashlight or a headlamp. It will be reached by two little gas tubes. You’ll want to keep an eye on it while you’re at work. Turn the gas knob to the “Pilot” position and push and hold the button. This will initiate the flow of gas, allowing you to ignite the flame. Some water heaters feature a separate pilot mode button, which is commonly a red button, which you must push and hold in order to activate it. While keeping the gas pedal depressed, ignite the pilot light. Certain water heaters feature an igniting button that is red or black, while others must be lighted manually with a long lighter
  3. Some models include a red or black igniting button. Maintaining pressure on the gas knob or button for a full minute after the flame is ignited is critical. Then slowly release it while checking to see if the light is still on. Turn the gas knob to the “On” position and listen for the unmistakable “whump” or whooshing sounds that indicates the main burner has ignited. Enjoy your hot shower when you’ve replaced the lid.

Despite the fact that a single extinguished pilot light is normally caused by a natural fluctuation in gas pressure, recurrent faults suggest a more serious problem with the water heater itself. The most typical problem that causes repeated pilot outages is a filthy or bent thermocouple, which is a thin copper wire and rod that detects the presence of a flame and immediately switches the gas off when it detects a lack of flame detection.

What is a Thermocouple?

A thermocouple is sometimes referred to as a flame sensor in contemporary water heaters because of the way it detects flames. Your thermocouple is most likely twisted, filthy, or damaged if the pilot light continues to go out after you have completed the above-mentioned lighting procedures. For those who find that their pilot light is twisted and not near the burner, they may simply turn off the gas, shift it over, and attempt lighting the pilot again. It may be necessary to clean the water heater gas valve and the main gas line near the heater if this does not solve the problem.

  1. The burner is typically simple to remove by simply sliding it out.
  2. If this doesn’t solve the problem, you may get a new thermocouple for less than $15 at any hardware store or home improvement center.
  3. Rooter Plumbing to help you get hot water back into your home again.
  4. The use of hot water is simply one component of a great showering experience.
  5. Previous PostNext Post Previous Post

How to Tell If the Pilot Light is Out on Your Water Heater

If you have a gas water heater, there is a good probability that your pilot light has gone out at some point in time. In a gas water heater, the pilot light is a critical component, and if it is not lighted or is not operating correctly, your “hot” water will become cold very quickly. Learning some basic troubleshooting techniques and how to activate the pilot light can help you save money by allowing you to address the problem yourself rather than hiring a professional plumber. Despite the fact that electronic ignitions are becoming increasingly widespread on contemporary gas water heaters, many older models still rely on pilot lights.

This article will assist you in troubleshooting the issue and determining what steps to take next.

What is a Pilot Light? What Does it Do?

Typically, a tiny flame is used to light the burner in gas and propane-fueled water heaters. It is this little flame that is referred to as a pilot light, and it remains lit at all times. When the water heater needs to heat the water in the tank, it uses the pilot light to start the gas burner, which then heats the water in the tank. Consider the pilot light to be similar to a match. You might use a match to start a fire or ignite a gas stove, for example. It is impossible to build a fire or light your gas stove if you don’t have the right kind of match on your person.

The loss of the pilot light will prevent your water heater from being able to ignite the gas burner, and as a result, it will be unable to heat the water.

Yet once the pilot light is restored, the water heater is capable of re-igniting the gas burner and resuming its function of heating the water.

Signs Your Pilot Light Has Gone Out

Generally speaking, there are three basic signs that your pilot light has gone out: In the event that your hot water is no longer hot, there is a significant likelihood that your pilot light has been extinguished. There are, of course, other possible causes for your lack of hot water, so if it isn’t the pilot light, you’ll need to perform some further troubleshooting. On the gas control valve, you may observe an error message or a blinking light indicating that there is a problem. If you are experiencing a difficulty, the indicator light may change colors to notify you to the situation.

The fact that the pilot light is not working is always one of the difficulties mentioned.

Learn how to do so by reading the information below:

How to Check if Your Pilot Light is Out

Even if your gas control valve shows that there is a problem with the pilot light, it is always worthwhile to visually inspect the area for a flame. The burner chamber door of a water heater is normally located below the gas control valve, at the bottom of the unit, on the left side of the unit. According on your water heater, you may need to remove the door or open it to get a good look at what’s going on within the burner chamber and in the pilot light tube.

It is unlikely that the problem is with the pilot light if there is a flame visible. If you do not, on the other hand, the pilot light has been extinguished.

What Causes a Pilot Light to Go Out?

There are a variety of various reasons why a pilot light may go out in a home. Here are a few of the most prevalent reasons for this condition: Change in Gas Pressure- When there is a natural change in gas pressure, it is fairly unusual for the pilot light to go out. Although it is unlikely to occur frequently, it does happen from time to time, and relighting the pilot usually remedies the issue. If, on the other hand, the pilot light continues to go out, this indicates that something else is wrong.

  • This stops gas from entering the chamber from entering.
  • More information about troubleshooting a thermocouple may be found in this article.
  • Because the pilot light is only a little flame, it can be quickly extinguished if the heater is installed in a drafty location of the house.
  • Because it is positioned in a closet or other enclosed space where it will not have access to the air it requires for combustion, it is possible that the pilot light may not remain illuminated.
  • It is possible that this condition could be hazardous to your health since it will result in a buildup of carbon monoxide in your house.

Is it Dangerous if the Water Heater’s Pilot Light Goes Out?

When the water heater pilot light is turned off, it is generally not a safety hazard to turn it back on. This is due to the fact that modern gas-fueled water heaters are equipped with valves that automatically shut off the gas supply when the pilot light goes out. This is a very critical safety feature, and if your water heater did not perform this function, you would be dealing with a natural gas or propane leak, which might result in an explosion. Having said that, when the water heater is located in an enclosed place, it might be quite dangerous.

Carbon monoxide is exceedingly hazardous and has the potential to be fatal.

They are affordable and may be installed in close proximity to your hot water heater.

How to Light a Pilot Light

Every water heater is a bit different, so be sure to read the directions that come with your specific make and model of water heater before starting.

In most circumstances, the following information may be found on a sticker attached to the side of your water heater:

  • Enable for a 10-minute period of time after turning off the gas control valve to allow the gas to exit the chamber region
  • Turn the knob on the gas control valve to the PILOT position and push the button. As a result of pressing the button, a little amount of gas will be transported to the pilot
  • For 90 seconds, press the little black (or red) igniting button on the side of the stove frequently. The igniting button will cause a spark to be generated, which will ignite the pilot. (Some water heaters may require manual lighting with a long lighter
  • This is not uncommon.) As soon as the status button starts blinking or turns on, the pilot light is turned on. At this point, you may adjust the temperature by turning the knob to the appropriate setting. You should be able to hear the burner start up. You should expect this to happen
  • If your pilot does not light after 90 seconds, you will need to wait for 10 minutes before attempting to light it once more. If, after multiple efforts, you are still unable to ignite the pilot, there may be an underlying problem.

Take a look at the video

Do I Have a Bad Thermocouple?

When it comes to contemporary water heaters, thermocouples are commonly referred to as flame sensors, although many of them feature a standing pilot light that is powered by a thermocouple. It is possible that the thermocouple is not functioning correctly in this instance, and the pilot light will not remain lit. Although it’s conceivable that the thermocouple is dusty or twisted, or that it’s damaged, it’s typically preferable to just replace the thermocouple rather than repositioning or cleaning it.

You may find out more about it here.

How Long Does it Take to Get Hot Water

It will take some time until you get hot water again once you have gotten your water heater back up and running. The length of time it takes depends on the size of the tank. As a general rule, you should anticipate to wait between 30 and 40 minutes until your tank has reached its maximum temperature.

Can I Turn Off My Pilot Light?

When it comes to turning off the pilot light on your water heater, there’s nothing wrong with it in general. Keep in mind, however, that you will not have access to hot water after the water in the tank has cooled down to a safe temperature. In truth, there are several circumstances in which turning off your pilot light is a wise decision. For example, when going on vacation, it is frequently recommended by professionals that you do so. You will save money on your energy bill if you turn off the pilot light on your water heater while you are away from home since the water heater will not keep the water heated while you are away.

Despite the fact that the heater will continue to consume a little amount of gas to keep the pilot lit, it will be less of a problem to turn on the water heater when you return since you will not have to relight the pilot when you return.

When to Call a Professional Plumber

It’s never a bad idea to have a professional plumber check at your water heater if you notice something is wrong with it. While they’re checking on your pilot light, they may also do periodic maintenance on your system to keep it running smoothly. Water heater maintenance should be performed at least once a year to prevent sediment buildup and corrosion. Proper maintenance will also increase the service life of your water heater. Even yet, it is not always essential to engage a professional plumber to assist you with the task of lighting your pilot light.

If, on the other hand, you believe the problem is related to the thermocouple in your water heater, you may want professional assistance.

If you hire a competent plumber, he or she will be able to replace or repair your thermocouple quite quickly and simply. Find a Local PlumberToday is the day to fix your plumbing emergency!

How To Tell If Pilot Light Is Out On Water Heater?

In the case of a gaswater heater, one of the most typical problems that might arise is the failure of the pilot light to illuminate. Typically, a pilot light is a small natural or liquefied petroleum gas flame that is used as an ignition source for a larger gas burner with higher power. The pilot light used to be left on all of the time in the earlier days, but that technique turned out to be incorrect since it wastes large amounts of gas that are not required. Nowadays, the majority of gas burners are ignited by electricity.

  • The phrase “pilot light” can also refer to an electrical indicator light that indicates whether or not electrical power is available or whether or not an electrical gadget is operational.
  • If you have an older gas water heater that is still ignited by a pilot light, it is critical that the pilot light is working properly.
  • You may save a significant amount of money by repairing the problem yourself rather than contacting a professional plumber.
  • So let’s get this party started.

How To Tell If Pilot Light is Out On Water Heater?

So, how can you tell if the pilot light on your water heater is out? The most obvious indicator that the pilot light has gone out is that the water will not heat up. In addition to seeing a blinking light (an error message) or not being able to see the flame, the two additional most typical indicators that the pilot light is out on a water heater are as follows: If the pilot light on the water heater goes out, it is not a life-threatening situation. However, if you become aware of this, you should move quickly to resolve the situation.

What is a Pilot Light? What Does it Do?

In certain gas-fired equipment, such as furnaces, a pilot light is a little flame that is constantly present. In older gas and propane water heaters, a little flame is utilized to ignite the burner, which might be difficult to see. When the water in the tank should begin to heat up, the pilot light is used to ignite the gas burner, which then heats the water in the tank. Consider the pilot light to be the match that ignites the flames of a gas stove’s burners. It is not possible to start a fire or turn on the gas stove unless you have this item.

If the pilot light on your water heater goes out, the gas burner will not be able to start, and the water heater will not be able to heat the water.

Signs That Pilot Light Has Gone Out

In certain gas-fired equipment, such as furnaces, a pilot light is a little flame that is constantly on. In earlier gas and propane water heaters, a little flame is employed to ignite the burner. The pilot light is used to ignite the gas burner when the water in the tank is ready to begin heating. To understand what the pilot light is, think of it as the match that ignites the fire in a gas stove. Building a fire and turning on the gas stove are both impossible without it.

For a pilot light, the same may be true. Your water heater will not be able to heat water if the pilot light goes out because the gas burner will be unable to ignite. The fact that you can only run cold water is the most prevalent indication that the pilot light is not working.

  1. If you are unable to run any hot water, there is a significant chance that your pilot light has malfunctioned. Of course, there are a variety of additional factors that might contribute to a lack of hot water. If the pilot light is operational, you will need to do more investigation to determine the source of the problem. On the gas control valve, you can see an error message or a flashing light that changes colors every now and then to alert you to a potential problem. Gas Control Valve Indicator The light in question is an indication light. Look for a sticker on the tank’s sidewalls that describes the significance of the indicator message and where it may be found. If this is the case, it is reasonable to assume that the pilot light is not working properly. No flame– When performing a visual check of the water heater, pay close attention to whether or not there is a flame. It is almost certain that the absence of a flame is a result of the pilot light being turned off.
See also:  How To Reset A Navien Water Heater?

If you are unable to run any hot water, it is likely that your pilot light has failed. There are a variety of different factors that might contribute to a lack of hot water. Even if the pilot light is operational, you will need to do more investigation to determine the source of the problem. Gas Control Valve Indicator– On the gas control valve, you can see an error message or a flashing light that changes colors periodically to alert you to a potential problem. An indication light is illuminated by the light in question.

If this is the case, it is reasonable to assume that the pilot light is not working properly; No flame– When performing a visual check of the water heater, pay close attention to whether or not there is a flame present.

Best Way To Check If Your Pilot Light Is Out

Check to See If Your Pilot Light Is OutEven if your gas control valve indicates that there is an issue with the pilot light, it is still worthwhile to visually verify a flame. Open the burner chamber door, which is normally placed below the gas control valve, which may be found at the bottom of your water heater. Depending on the model of your water heater, you’ll need to either remove the door or open it in order to examine the burner chamber and pilot light tubing within. If there is a flame, the fault is not with the pilot light; however, if there is no flame, the problem is with the pilot light.

What Causes a Pilot Light to Go Out?

There are a plethora of reasons why a pilot light may cease to function correctly. The following are the most often encountered:

  • Increase or decrease in Natural Gas Pressure–Increases or decreases in natural gas pressure have an impact on a variety of aspects of human life, including the correct operation of electrical equipment. As a consequence of a natural fluctuation in gas pressure, problems with the water heater might occur as a result of the pilot light failing to illuminate. It doesn’t happen very frequently, but when it does, re-igniting the pilot light typically takes care of the problem immediately. If the pilot light continues to burn out, it is likely that something else is amiss.
  • Its primary duty is to act as a safety device, shutting down the gas valve when the pilot light goes out. The gas is prevented from entering the chamber as a result of this. It is possible that the pilot light will be turned off even if everything else is operating properly if the thermocouple in your heater begins to malfunction or becomes broken and dirty.
  • Draft– A rush of air can sometimes extinguish the pilot light in the combustion chamber, causing it to go out. When the water heater is not properly sealed, this occurs. It’s also possible that the heater’s pilot light, which is effectively just a little flame, will be blown out if it’s installed in a very drafty area.
  • Lack of Combustible Air– Gas appliances, in general, and water heaters in particular, require air to operate properly. It is not possible for the pilot light to remain lit if your device is placed in a closet or other enclosed space where it will not have access to any natural light or ventilation. In order for combustion to take place, air must be present.

If this is the case, we strongly recommended that you seek the assistance of a professional to aid you in diagnosing the issue at hand. The fact that you presumably desire a working water heater is secondary to the reality that this condition might be potentially dangerous since carbon monoxide is accumulating inside your house.

Is It Dangerous If The Water Heater’s Pilot Light Goes Out?

If you notice that the pilot light is not working, it is not dangerous. Water heaters are normally not harmful when the pilot light is turned off, but sometimes they are. The vast majority of modern gas-fueled water heaters are equipped with valves that automatically cut off the gas supply when the pilot light fails to illuminate. This is a key safety feature that has prevented innumerable accidents from occurring. You might be dealing with a natural or propane gas leak, which could potentially end in an explosion, if your water heater does not perform this function properly.

As an example, if the pilot light fails to illuminate due to a lack of combustible air, carbon monoxide can build up in the surrounding area, which can be fatal due to the dangerous nature of the gas.

How To Light A Pilot Light On Water Heater

Water heaters are available in a variety of designs. As a result, they are all a little bit different from one another.

When lighting the pilot light, it is usually a good idea to double-check the user handbook or the label that has been placed on one of the sides for specific instructions. Here are some general instructions that are applicable to the majority of models:

  • Turn the gas control valve to the OFF position and wait for the gas to clear the chamber area for 10 minutes. Set the knob on the gas control valve to the PILOT position and push the button. When you click the button, a little quantity of gas will be sent to the pilot
  • For 90 seconds, continually press the small black (or red) igniting button to start the pilot. A spark created by the initiating button will ignite the pilot, illuminating it. For certain water heaters, manual lighting with a long lighter may be necessary
  • The pilot light is activated when the status button begins to flicker or illuminates. The temperature knob should be adjusted to your favorite level during this time. After then, you should be able to hear the burner begin to heat up. Take no notice of this sound
  • It is quite normal. If the pilot does not light after 90 seconds, wait at least 10 minutes before attempting to light the pilot once more
  • It is possible that the pilot will not light after several attempts
  • Alternatively, you may require the services of a professional to light the pilot for you.

Take a look at the video

Do I Have A Bad Thermocouple?

With modern water heaters, thermocouples are frequently referred to as flame sensors, and as a result, numerous heaters are equipped with a standing pilot light that is powered by a thermocouple. In this circumstance, if the thermocouple is not operating properly, the pilot light will not remain illuminated. In most cases, you will be able to modify or clean the thermocouple; but, in other cases, replacing it will be the most cost-effective solution. Depending on your previous experience with home improvement tasks and working with gas appliances, you might be able to manage this project.

How Long Does It Take To Get Hot Water?

When the water heater is turned on, it warms the water at its own rate. As a result, once your water heater is up and running, it will take some time until you have hot water again. The length of time required is determined on the size of the tank. Expect to wait 30 to 40 minutes on average for your tank to reach its full shower-ready temperature, according to the manufacturer.

Can I Turn Off My Pilot Light?

In most cases, turning off the pilot light on your water heater will not cause any problems. Keep in mind that once the water in the tank has cooled, you will no longer be able to use the hot water in the faucet. In reality, there are instances when turning off your pilot light is a wise decision. When it comes to traveling on vacation, for example, specialists usually urge you to do just that, according to the experts. You’ll save money on your electricity bill since the water heater won’t have to work as hard to keep the water warm while you’re away.

It will be easier to start the water heater when you arrive since the pilot will not need to be re-lighted, even if a small quantity of gas will still be required to keep the pilot lit on the heater.

Final Thoughts

It is recommended that you get your water heater tested by a professional plumber on a regular basis, just as you would with any other household appliance. During this time, they can execute a routine maintenance process on the system while keeping an eye on the pilot light. Maintenance should be performed at least once a year, according to experts, in order to prevent sludge and corrosion from forming. This should significantly increase the lifespan of the water heater. It is not required to hire a professional plumber to ignite a pilot light in most cases.

Some people, however, may not feel secure enough to take on these kind of home renovation projects, which is quite understandable.

In certain instances, the problem isn’t even that straightforward. Take, for example, if the problem is caused by the thermocouple on your water heater. You’ll still require expert aid in such case. Please do not hesitate to contact us if you have any more inquiries.

Why Your Water Heater’s Pilot Light Keeps Going Out & How to Fix It

Getting your water heater tested by a skilled plumber is recommended every few years, just as you would with any other household device. As long as the pilot light is not out, they can execute a routine maintenance procedure on the system. Specialists recommend doing maintenance at least once a year in order to prevent silt and rust from forming. The water heater’s lifespan should be significantly increased as a result of this. In most cases, it is not required to hire a professional plumber to ignite a pilot light.

It is quite acceptable for some people to be apprehensive about doing these kind of home renovation projects.

Suppose the problem is caused by the thermocouple in the water heater, for example.

Feel free to contact us if you have any more queries.

Why does the pilot light on my water heater keep going out?

Because of problems with the heater’s thermocouple or owing to access to combustible air, your water heater’s pilot light continues going out repeatedly.

Thermocouple Issues

When your pilot light is on, your thermocouple detects the presence of the flame. The thermocouple’s tip is positioned above the pilot flame, providing a voltage that maintains the gas valve open in the process. A thermocouple will shut down the gas supply to your water heater if it detects that the pilot light on your water heater is not lighting up properly. When thermocouples are exposed to moisture or dust for an extended period of time, they might malfunction, gather dust, or get bent away from the pilot light’s flame.

Lack of Combustible Air

Another reason why your gas water heaterpilot light won’t remain lighted might be that there isn’t enough combustible air in the room where it is located. To keep the pilot light on in your water heater, you’ll need to blow air into it. Otherwise, the flame will be extinguished. Take precautionary measures to ensure that the water heater is not surrounded by material, such as litter or lint, which might increase the quantity of combustible air present. Maintain as much cleanliness as possible in the surrounding region.

What do I do if my water heater pilot light keeps going out?

Try to rekindle the spark on your own first, if at all possible. Take the following general steps:

  1. Locate the gas shut-off knob and turn it all the way to the “Off” position. The gas flow is halted as a result of this. Allow for a few minutes for the gas to dissipate before continuing. To get access to the burner, remove the access panel. To begin the flow of gas, turn the knob to the “Pilot” position. You’ll want to press and hold the knob down for a few seconds. While still holding the gas knob, ignite the pilot with a long lighter while still holding the gas knob. To ignite your gas water heater, use the button on the side of the tank that says “ignite.” As soon as the flames have been extinguished, turn the gas knob to the “On” position and wait for the main burner to come on.

If you are unable to relight the pilot or if your pilot light keeps going out, it is possible that you have another problem, such as a faulty thermocouple, to consider. Please refer to the owner’s handbook for your water heater equipment for further information.

Can I replace a thermocouple myself?

Yes. In the event that you are handy with tools, you may be able to change the thermocouple yourself. It is easier to accomplish this by turning off the gas valve and removing the entire burner and thermocouple assembly.

In the case of minor repairs, it is preferable and safer to hire someone who is knowledgeable in the field of repair. A specialist may also evaluate your water heater for other faults and provide advise or ideas on how to deal with any existing or future difficulties that may arise.

Call BGE HOME

Please contact BGE HOME at (410) 918-5600 if your water heater pilot light will not light or continues going out. You may also contact us online. Our licensed specialists are available 24 hours a day, seven days a week to come out and inspect your water heater and make recommendations on how to get it running safely and effectively again. This item was posted on Thursday, May 13th, 2021 at 4:09 pm and is filed under Uncategorized. Commenting and pinging are temporarily closed for this post.

Solved! What to Do When Your Pilot Light Goes Out

Image courtesy of fotosearch.com The temperature in my shower this morning was absolutely freezing, and I mean that in the best way possible. After a brief investigation, I noticed that the pilot light on my water heater had gone out. Is it worth it to try to relight it? A: It all depends on what caused the light to go out. It’s possible that the problem was anything as simple as a draft, a filthy pilot orifice, or a worn-out part—or that the extinguished pilot light was a symptom of something more serious requiring attention.

If you find yourself in this situation, leave your home and call the gas company!

(Please keep in mind that if your water heater has an enclosed burner chamber, you’re most likely out of luck as far as a DIY remedy is concerned; only a professional plumber should be able to reach an enclosed burner chamber.) Make an appointment with a proGet free, no-obligation repair quotes from qualified appliance experts in your area.

When you see your pilot light out, you can usually relight it.

The presence of a downdraft in a vent pipe on a windy day, or even the breeze via an open window, can be sufficient to extinguish a pilot light. It is common for water heaters to include identical relighting instructions, which are usually permanently mounted to the side of the appliance. Image courtesy of fotosearch.com Remove the access cover located at the bottom of the water heater in order to relight the pilot. Ensure that the “Pilot” position is selected for both the control knob and the water temperature knob.

Continue to keep the knob down for a full minute after the pilot is ignited in order to remove any remaining air from the line.

Depending on what happens after the pilot ignites, one of the following options should be considered:

  • If the flame continues to burn, you’re good to go!. Simply replace the cover plate, turn the control knob to the “On” position, and set the desired temperature on the water temperature knob to return to the refreshinghotshower experience. Ensure that the pilot light does not flicker and goes out immediately after relighting by cleaning the pilot orifice. Gas flow is impeded by a clogged pilot light aperture, but the solution is straightforward. Shut off the gas to your water heater first, of course (look for a valve on the gas line that supplies the unit). Twist the pilot orifice fitting to the left, which is positioned behind the access cover, to release it from its mounting. After that, remove the orifice itself from the fitting by unscrewing it. Using a cotton swab moistened with rubbing alcohol, thoroughly wipe all surfaces of the fitting once it has been dismantled. As soon as you have completed the reassembling and reattaching of the fitting, relight the pilot light as previously specified. You should replace the thermocouple if you are able to ignite the pilot light but it goes out as soon as you remove the control knob from the pilot light control box. It is a safety device that shuts off gas flow if it detects that the pilot light is out
  • However, if it becomes broken, it loses its capacity to regulate the flow of gas. This repair is a little more involved than the previous two, but a replacement is rather inexpensive—often costing less than twenty dollars

Connecting the control panel to the burner assembly, which is hidden behind an access panel, is this item that looks like a copper tube. Turn off the gas to the water heater before beginning any disassembly efforts. Remove the burner assembly from the control panel by detaching the thermocouple tube, the pilot light tube, and the gas supply tube using an adjustable wrench. The burner assembly should simply slide out of the way. (Tip: Because thermocouples come in a variety of sizes and kinds, bringing the broken thermocouple with you when purchasing a replacement is the most effective approach to ensure that you receive an identical match.) Replacing the broken thermocouple with a new one is followed by reassembling the burner assembly, reattaching the tubes, and relighting the pilot light in the manner indicated above.

Make an appointment with a proGet free, no-obligation repair quotes from qualified appliance experts in your area.

How to Know If Your Pilot Light Is Out

iStock/Getty Images image courtesy of turk stock photographer/Getty Images

See also:  Why Is My Hot Water Heater?

In This Article

  • What to do when the pilot light is out
  • What is the reason for the pilot’s departure? Restart the pilot in a safe manner

A standing pilot is the technical word for a pilot light, which is a tiny flame that is continuously burning in a closed space. In a natural gas or propane water heater, furnace, or boiler, it is responsible for igniting the gas burner flame, and if it fails to do so, the device will not run. The failure of your gas furnace to give heat or the failure of your gas water heater to deliver hot water is generally the first indicator that the pilot has been extinguished in your gas furnace or water heater.

However, certain low-end appliances, as well as older appliances that have been in operation for 20 years or more, still feature pilot lights.

First and foremost, you must ensure that the flame has truly been extinguished.

How to Check the Pilot Light

It is a very solid indication that the pilot light has gone out in a heating or hot water device, especially if the equipment in issue is a furnace and the fan is still operating. When it comes to furnaces, though, there are a few additional components that might cause a gas shutdown, so you should visually inspect the pilot, which is thankfully as simple to accomplish for a furnace as it is for a water heater. You’ll need to remove the furnace cover in order to access the gas control knob, but the gas control knob on a water heater is plainly displayed on the front of the tank, approximately a foot above the floor, if you’re monitoring the pilot on a furnace.

Keep an eye out for the hollow into which the tubes extend from the gas control; it is within this cavity that you should be able to see the pilot flame blazing.

If you don’t see that flame, it means that the pilot has gone out completely.

Why Has the Pilot Gone Out?

A standing pilot flame is similar to that of a match, and it may be extinguished by a powerful blow of air. If that’s what occurred, you shouldn’t have any problem getting it back up and running, but you’ll probably want to take precautions to avoid it blowing up again in the future. Another possibility is that the appliance ran out of gas because your propane tank is nearly empty, in which case you will be unable to relight the pilot. Some of the other choices aren’t as straightforward. An issue with thethermocouple, which is a safety component that shuts down the gas valve when the flame goes out, might be the cause of this problem.

It’s also possible that debris is obstructing the pilot orifice; if this is the case, you may be able to restart the pilot, but it will burn with a flickering orange color and will go out again in a matter of minutes, hours, or days.

There might be a leak, and there could be an explosion if there is a flame present.

Depending on the model, some units feature a piezoelectric spark ignitor to get the pilot flame starting; if this is the case, a green or red button will be located adjacent to the gas control knob.

Remember to keep the knob turned in for 10 to 20 seconds after the flame is ignited to give the thermocouple enough time to warm up before moving it.

How to Fix a Water Heater Pilot Light

Time Approximately one hour or less Complexity Cost for a beginner is less than $20.

Introduction

Time It will take no more than an hour. Complexity Less than $20 for a beginner

Tools Required

Is there no hot water? If you have a natural gas or propane water heater, there is a good probability that the pilot light has gone out. It is this little flame that starts the gas burner on your water heater that is referred to as the pilot light. When the pilot light on your water heater goes out, the first thing you should do is try to relight it by following the instructions on the water heater label. The thermocouple is by far the most prevalent cause of pilot failure, whether it occurs immediately after lighting or on a regular basis after the pilot has been extinguished.

If you do not wait for a professional to arrive, you will be able to get your hot water running without incurring the expense of a service visit.

What is a Thermocouple?

  • What if there’s no running water? A natural or propane gas water heater’s pilot light is most likely out if you have one of these appliances. This little flame serves to start the gas burner in your water heater, which is controlled by the pilot light. If you notice that the pilot light on your water heater has gone out, try to relight it by following the instructions on the water heater’s label. The thermocouple is by far the most prevalent cause of pilot failure, whether it occurs immediately after lighting or on a regular basis after the pilot has been ignited. Fortunately, most thermocouples can be replaced for a low cost and in less than an hour, which is a welcome relief. If you do not wait for a professional to arrive, you will be able to get your hot water running without incurring the expense of a call. To discover how to light a pilot light, continue reading this article.

Project step-by-step (6)

  • Shut off the gas line by closing the cutoff valve. As seen in this photo, turn the valve a quarter turn so that the handle is at a right angle to the pipe.

Unscrew the Nuts

  • Turn off the control valve if it is on. Remove the burner access covers and loosen the bolts on the gas, pilot, and thermocouple lines to free up the burner.

Sign Up For Our Newsletter

Turn off the control valve if it is still on. Unscrew the nuts on the gas, pilot, and thermocouple lines by removing the burner access covers;

Remove the Assembly

  • Remove the water heater pilot light burner component from the water heater. Remove the old thermocouple by unscrewing or pulling it out. Purchase a new one that is the same size and length as the previous one

Install the New Thermocouple

  • Install the new thermocouple in the same manner as the previous one
  • Replace the burner assembly by sliding it back in. Reattach the three wires to the control valve where they were disconnected.

Reattach the Lines to the Gas Valve

  • Installation of the new thermocouple is identical to the installation of the previous one. re-insert the burner assembly into the burner assembly The three wires to the control valve should be reconnected.
  • Pro tip: Because the metals are delicate, avoid overtightening them.

Test for Gas Leaks

  • Keep in mind that in order to test for leaks, the pilot light must be lighted and the burner turned on so that gas flows through the big tube.
  • Replenish the water supply by opening the shutdown valve and lighting the pilot light. Turn the control valve to the “on” position. Use a 50/50 mixture of dish soap and water to check the screw joints for air bubbles, which indicate a leak, while the gas burner is turned on.
  • Keep in mind that when the water heater pilot light is re-ignited, the flame should wrap around the thermocouple bulb.

CAUTION!

During this procedure, you should not be able to detect the scent of gas (except for a slight whiff when you remove the gas lines). If you find yourself in this situation, exit the house immediately and contact your gas provider.

WhenNotto Replace the Thermocouple

Some gas water heaters have a burner chamber that is “closed,” making it impossible to reach the burner. It is recommended that you contact a professional to repair this sort of heater. In addition, some gas water heaters are not equipped with pilot lights. Allow the professionals to take care of this as well.

How to Relight Your Water Heater’s Pilot Light

An Overview of How to Turn on a Water Heater Pilot Light

  • Step 1: Turn off the gas
  • Step 2: Put the controls in “pilot mode.” Step 3: Press the control button and the light button simultaneously. Step 4: Bring the water temperature back to normal. Step 5: Reinstall the lid.

Don’t freak out if you find yourself without hot water for no apparent reason. It’s possible that the pilot light on your gas water heater has gone out. Despite the fact that this little blue flame should always be burning, it can go out for a variety of reasons. The good news is that, in the majority of situations, relighting is a simple process. This Might Also Be of Interest to You: Using These 5 Simple Steps, You Can Relight Your Furnace Pilot Light Please see the following steps for relighting the pilot light on your gas water heater.

How Do I Know If My Pilot Light Is Out?

In the event that you turn on a faucet and the water comes out cold, no matter how long you let it run, it is likely that your pilot light is out. You’ll need to get to the water heater in order to examine it. Most water heaters have a pilot light that is situated at the bottom of the machine, below the gas control valve, which makes it easy to find. Look into the burner chamber by opening the access panel or entrance to the chamber. The pilot light tube may be found in this location, and it should have a continuous blue flame.

Can I Relight the Pilot Light by Myself?

Whenever you turn on a faucet, no matter how long you let it run, the water will come out cold. This indicates that your pilot light is not working properly. The water heater must be accessed in order to be checked. Pilot lights are often found at the bottom of the water heater, just below the gas control valve, and are illuminated by a small flame or flame indicator.

Examine the inside of the burner chamber by opening the access panel or door. Within the pilot light tube, which should have a constant blue flame, you’ll locate the ignition switch. If you don’t see a flame, this indicates that the pilot light is not working properly.

  • Here is an estimate of how much it will cost to replace a water heater: When your water heater isn’t working, you’ll notice these seven tell-tale signs. Learn how to properly drain a water heater. What is a Smart Water Heater and how does it work? I’m wondering how much a tankless water heater will set you back.

What Do You Do When the Pilot Light Goes Out?

Re-lighting the pilot light according to the manufacturer’s instructions for your equipment should be attempted if at all possible. The procedure, on the other hand, is very consistent across different kinds of gas water heaters. To begin, establish if your water heater is equipped with an automated or manual ignition system. A glimpse at the control dial should be enough to notify you, according to Mullen Plumbing, Heating, and Cooling of West Virginia. If you have an automated igniter, it is likely that you have an ignition button.

It will be necessary to manually relight your pilot light.

How to Light a Pilot Light on a Water Heater Without an Automatic Igniter

  1. Using the access cover, switch the gas control valve to the “off” position to cut off the gas supply. Allow about 10 minutes for any gas that has gathered to disperse. The “pilot” position is reached by turning both the control and the water temperature knobs. To activate the control knob, depress it. To re-ignite the pilot light, hold the button down while using a wand lighter or long match to ignite it. A continuous flame should be visible once the pilot light has been turned on. For a full minute, continue to keep the knob down to force air out of the line that has accumulated over the course of time. Turn the knob to the left
  2. Set the temperature of your water heater back to the appropriate level by turning the control knob. Remove the access cover and replace it.

How to Light a Pilot Light on a Water Heater With an Automatic Igniter

  1. Remove the access cover from the door. To turn off the gas, turn the gas control valve to its “off” position. Wait about 10 minutes for the gas to disperse before continuing. Then, set the control and water temperature knobs to the “pilot mode.” To use the control button, press it. While maintaining pressure on the trigger, continually push the striker knob for approximately 90 seconds, or until the pilot is lighted. The striker knob is usually either black or red in color. Continue to hold down the control knob for a full minute to bleed air from the line, then release it.
  2. Set the temperature of your water heater by turning the control knob to the appropriate setting
  3. Replace the access cover in a safe manner.

Your pilot light should remain bright if it was accidentally turned off due to a draft or similar one-time problem. If it doesn’t work the first time, wait 10 minutes before attempting to ignite it yourself again after that. Having trouble with your water heater’s pilot light? It’s possible that your device requires expert maintenance or repair. Because we are spending more time at home than ever before, it is critical to be prepared for unexpected home repairs with a plan from HomeServe. The knowledge that you can easily call our 24-hour repair hotline in the event of a covered breakdown provides you more peace of mind.

Why Your Pilot Light Keeps Going Out & How To Fix [With Pictures]

That darn pilot light just won’t stay turned on! Moreover, it is causing all of your plans for today to be derailed. Nothing compares to the sensation of taking a hot water shower. However, there are times when this does not occur. After all, there are worse things than having a very cold bath, should we say? The one thing that everyone despises is a lack of running water. This may be incredibly inconvenient – not only for showering, but also for all of the other duties that require hot water to be completed successfully.

You don’t have to put your day on wait because your pilot light isn’t working properly.

However, if you discover that your water heater is leaking water and that this is the root of your water problem, read our guide on what to do when your water heater is leaking water!

What’s A Pilot Light?

An electronic device that maintains a continually burning flame is known as a pilot light. Basically, the goal of this section is to light the burner. How? When you switch on your appliance, gas is released from the main burner, and the pilot light flame ignites the gas, so supplying heat to the room. With each degree of heat generated by the main burner, the air or water contained within your appliance is heated and then disseminated as needed around your residence or place of business

Appliances With Pilot Lights

Water heaters, older furnaces, and boilers are more likely to have a pilot light than other types of appliances. You may also discover that your gas fireplace has a pilot light, which is a good thing. Learn how to switch on the pilot light on your gas fireplace by visiting this page. Pilot lights have been gradually being phased out in favor of hot surface igniters or spark igniters in more recent years. pilot light for a water heater The pilotflame ignites the gas, which generates heat for your house or place of work.

If your hot water isn’t functioning, check the pilot light on your water heater. Also, if you are experiencing no heat, check to see whether the pilot light on your furnace or boiler has gone out. furnace with pilot lightBoiler with pilot light

Water Heater Pilot Light: Where Is It And What Does It Do?

A little access panel, located just underneath the thermostat, may be found at the very bottom of your gas water heater. The pilot light for the gas water heater is located within the access panel. There will be a gas panel where you may check to see if the pilot flame has been ignited. The pilot light on your water heater is a little flame that is used to ignite the gas burner in the water heater. This is required for the purpose of heating the water that will be dispersed around your home. If you are experiencing no hot water and have attempted to relight your pilot light without success, you will require water heater repair.

See also:  How To Prime Rv Water Pump

Warning!

This photograph was shot by a water heater professional for the purpose of giving a demonstration on the use of pilot lights.

What Makes Your Water Heater Pilot LightGo Out

Thermocouple on the water heater is faulty. The thermocouple is responsible for detecting whether your pilot light is on. This copper rod serves as a safety precaution, preventing the heater’s gas supply from being turned off if the pilot light on the water heater goes out. The natural wear and tear of a thermocouple can cause it to get twisted out of place, to malfunction, to become broken, to become covered in dirt, or to accumulate carbon deposits. When one or more of these conditions occurs, the thermocouple will be unable to reliably detect the pilot light and will subsequently shut down the heating system.

Strong Breeze Can Blow Out Pilot Light

In some cases, such as when there is heavy wind or a nearby draft, your pilot light may be extinguished. Unless your pilot light has simply been out, you should have little trouble re-igniting it and keeping the flame burning.

Kink in the Flex Tube

The fuel is delivered to the gas controller by flexible tubes. Gas will not flow through the tube if there is a kink or twist, which can also lead to pilot light difficulties.

Filthy Pilot Light OpeningCan MakePilot Light Keeps Going Out

If the pilot’s mouth is clogged with muck and debris, it will be virtually hard for it to maintain a flame. It will only keep a modest flame that will be readily extinguished if it does catch fire. Your pilot light will not stay lit if your pilot orifice is clogged with debris.

How Do I Re-Light My Gas Water Heater Pilot Light?

The pilot light on the water heater is not lighted.

Step 1: Thoroughly Read Gas Water Heater Manual

To have a better knowledge of where each component of your water heater is situated, consult your water heater’s instruction manual.

Step 2: Turn Down Thermostat

To have a better knowledge of where each component of your water heater is situated, consult your water heater handbook.

Step 3: Turn OFF Gas

The gas valve for the water heater Locate the gas shut-off valve and turn it all the way to the “Off” position. The gas shut off valve is positioned on the gas line near the base of your water heater, near the base of your water heater. Before proceeding on to the next stage, you must wait at least 5 minutes to guarantee that all of the gas has dissipated completely.

Step 4: After 5 Minutes, Turn The Gas Control Valve Setting On Water Heater To “Pilot”

Turn the gas control valve, which is situated on the water heater, to the “Pilot” position.

The word “Pilot” should be in the center of the image.

Step 5: HoldDownthe Reset Button

Keep the water heater reset button depressed. After that, press and hold the reset button. This is a button that is often red in color and is situated to the left of the gas control valve. Keep your finger on this button. To be on the safe side, use the instructions to identify each component.

Step 6: While Holding Down The Reset Button, Press TheIgniter

Keep the water heater’s igniter down. The igniter is located to the right of the gas control valve. While continuing to keep the reset button down, press the igniter button on your keyboard. Click on the water heater’s gas window until you see a blue flame appear in the glass.

Step 7: Continue To Hold Down The Reset Button For 20-30 Seconds.

Following the sighting of a flame and the removal of your finger from the igniter, you must continue to press the reset button. Continue to hold the button down for another 20-30 seconds.

Step 8: Turn The Gas Control Valve To The “On” Setting

It is necessary to maintain pressure on the reset button after you have seen a flame and removed your finger from the igniter. For a further 20-30 seconds, push and hold the button down.

Step 9: Turn The Thermostat Up

Increase the temperature of the water heater. Now is the time to dial up the heat in order to get that hot water flowing again!

Step 10: Enjoy Your Warm Water, Or Ask For Help!

If you try to relight the pilot light and it does not stay lit, you may want the services of a professional to assist you with your water heater repair.

But What If You Don’t Have A Manual Igniter?

After that, remove the access panel that is located beneath the water heater thermostat and discard it. You can use a wrench to help you.

After 5 minutes, Turn Gas Control Valve To “Pilot”

After that, remove the access panel that is located beneath the water heater’s temperature control. Use a wrench to get the job done.

Next, Hold Gas Control Valve Down And Ignite Pilot With A Lighter

Keep the gas knob pressed down as you ignite the pilot using a long lighter, similar to a BBQ skewer. If your gas water heater, on the other hand, has an igniting button, use it instead.

Once TheFlame Is Lit,Turn Gas Control Valve to “On”

As soon as the pilot light is lighted, you may remove the reset button and turn the gas knob to the “On” position, which will take around 30 seconds. You should be able to hear the main burner turn on at this point. Your pilot light should now be able to maintain a flame, and hot water should be flowing again!

Furnace Pilot Light: Where It Is And What Does It Do?

Old furnaces rely heavily on the pilot light to generate heat, which is why it is so crucial to keep the pilot light on. When the gas valve is opened, the flame will continue to burn constantly, igniting the gas. The heat generated by this process then heats the air that is drawn into your furnace, which is then dispersed throughout your house. If your furnace’s pilot light is out, you may notice that it is spewing chilly air into the house. The failure of the pilot light is one of several probable causes of your furnace’s inability to switch on.

You may find the pilot light by following the gas line into your furnace and looking for it there.

From there, you should be able to see a short tube that runs from the gas valve to the burner itself. You should be able to locate the pilot light if you follow the little tube leading to it.

Why Furnace Pilot Light keeps going out

There are a variety of reasons why the pilot flame on your furnace continues flickering out of control. Let’s get started!

Faulty Thermocouple Triggers Pilot Light to Go Out

It is meant to shut off the gas valve if the pilot light goes out, and it is used in conjunction with a thermocouple. Thermocouples can be damaged or worn out over time. If the thermocouple is incorrectly positioned or malfunctioning, the gas valve may be incorrectly shut off, as well as preventing the pilot light from keeping lit.

Dirty Thermocouple Makes Pilot Light Keeps Going Out

A filthy thermocouple may cause the safety mechanism to mistakenly trigger, causing the ignition to be turned off. The thermocouple has the potential to accidentally shut off the gas valve and extinguish the blazing flame.

Filthy Pilot Port/Orifice

Examine the flame. If the flame is becoming orange, contact an HVAC professional immediately. If you light your pilot and the flame is yellow, this indicates that your pilot opening is filthy and is preventing your pilot light from keeping lit for long periods of time. A buildup of dirt in the pilot light port might prevent the flame from fully enveloping the thermocouple, which can result in a faulty ignition. As a result, the safety system is activated, which results in the gas being turned off.

Bad Gas Regulator

Examine the flames if they are burning. Contact an HVAC professional immediately if the flame is orange! If you light your pilot and the flame is yellow, this indicates that your pilot light is not remaining lit due to a filthy pilot opening. Due to a buildup of dust and grit in the pilot light port, the flame may not be able to completely consume the thermocouple. Consequently, the safety system is activated, which causes the gas to be shut down completely. Your pilot light is most likely being affected by this problem, which is fairly frequent.

Bad Flue Venting Could Blow Out Pilot Light

Excess wind might enter via the openings in your flue pipe if it is loose, broken, or not correctly attached to the furnace. This would extinguish the pilot light flame.

A Strong Draft

There’s always the potential that a powerful draft knocked out your pilot light’s flame and caused it to go out.

How To Re-Light A Furnace Pilot Light?

You should never rule out the possibility that a strong draft was the cause of your pilot light being extinguished.

Step 2: Identify Pilot Light

Find the location of the pilot light in your furnace by consulting the owner’s handbook. In order to get access to the furnace, you will need to remove the front of the furnace.

Step 3: Turn OFF Gas

After that, locate the gas valve and shut it down completely. A tiny valve located towards the bottom of the furnace is standard on most models. In general, there are three settings for the gas valve: “ON,” “OFF,” and “PILOT.” Make sure the valve is in the “OFF” position by turning it clockwise. It is critical that you wait for at least 5 minutes after the previous step to ensure that all gas has been expelled from the pipes before proceeding. A disaster might occur if this is not done.

Step 4: WAIT 5 Minutes, then Turn Gas to “Pilot”

Immediately after waiting 5 minutes, switch the gas valve to the “PILOT” position.

It is vital that all of the gas has dissipated before switching the gas position to the pilot position. A few of minutes might be the difference between a peaceful society and a disasterous one. Keep in mind that gas is quite explosive!

Step 5: Hold Reset Button

Immediately after waiting 5 minutes, switch the gas valve to the “PILOT” setting. To ensure a smooth transition from pilot to gas, make sure all of the gas has been released. A few of minutes might be the difference between a peaceful society and a disasterous society. Never forget that gas is extremely dangerous.

Step 6: Press Igniter While Holding Reset Button

Holding the reset button down for a second or two will allow you to activate the igniter and light the flame. Once the flame has been ignited, remove the igniter and continue to hold down the reset button until the flame has been extinguished. Keep the reset button pushed for 20-30 seconds to complete the process. To light the pilot when you do not have a manual igniter, you can use a BBQ lighter or a match. furnace with a pilot light

Step 7: Turn Gas to “ON” position

Restore the pilot light by turning the gas control valve back to its “ON” position once it has been re-ignited. Right now, you should be able to keep your house warm!

Step 8: If you Aren’t comfortable yet, call a pro!

If, despite doing the necessary measures, you are still unable to keep your pilot light lit, contact an HVAC professional for furnace repair.

Boiler Pilot Light: Where It Is And What Does It Do?

The pilot light in your boiler is vital for the boiler to function properly and generate heat. It is necessary for the pilot to burn constantly in order for it to ignite the gas when the gas valve is opened. When this occurs, your boiler starts heating the water, which is subsequently dispersed throughout your house to provide warmth. If your pilot light goes out, your boiler and central heating will not be able to operate properly. The pilot light is placed within your boiler, on the other side of the valve from the gas valve.

Why Boiler Pilot Light Goes Out

A malfunctioning, misaligned, filthy, or damaged thermocouple is frequently the source of your pilot light’s failure to illuminate properly. It is the thermocouple that keeps the gas valve from opening if the pilot light is not lit. Your pilot light may not function properly if there is an issue with your thermocouple, or if it is just coated with dirt and debris.

Dirty Pilot Opening

When you turn on your furnace pilot light and find a yellow flame, this indicates that your pilot light is unclean and is causing your furnace pilot light to constantly turning out. If dirt accumulates in the pilot light port, it may prevent the pilot light from completely enveloping the thermocouple with the flame it produces. This causes the thermocouple safety system to be incorrectly activated, resulting in the gas being turned off and the heat being turned off.

Weak Gas Regulator Can Make Pilot Light Keeps Going Out

If you have gas appliances in your home, you will have a gas regulator outside your home. The failure of your gas regulator may result in your furnace not receiving enough gas to keep its pilot light lit. In the event that you observe pilot light issues on more than one device, such as your water heater, it is possible that your gas regulator is broken or weak.

A Strong Draft

A strong airflow has the potential to completely extinguish your pilot light.

How To Re-Light Boiler Pilot Light

Make sure you are familiar with the components of your boiler by reading the instruction manual thoroughly.

It is common for the owner’s handbook to contain instructions for re-igniting the pilot light.

Step 2: Shut OFF Boiler

Starting with shutting off the boiler is always a good idea.

Step 3. Shut OFF Gas

Locate the gas valve and turn it to the “OFF” position.

Step 4. Wait 10 Minutes

Continue to check the pipes for around 10 minutes to ensure there is no residual gas.

Step 5. Open Boiler and Locate Pilot Light

After a short period of time, you can turn on the boiler. To obtain access to the pilot light, remove the access panel from the wall. Typically, this panel is positioned next to the gas control knob box, which is where it gets its name. Sometimes you may simply lift the panel up, but other times it may be screwed to the wall or ceiling.

Step 6. Turn Gas to “Pilot”

You can now turn on the boiler after waiting a while. To obtain access to the pilot light, first remove the access panel. Typically, this panel is positioned next to the gas control knob box, which is a convenient location. Although the panel is sometimes simply lifted, it is occasionally fastened into place.

Step 7. Hold Reset Button, Then Click Igniter

Next, press and hold the reset button for a few seconds. While still holding down the reset button, press and hold the igniter button until you see a flame appear. It is necessary to press the reset button for an additional 20-30 seconds after the flame is ignited to ensure that it is fully functional.

Step 8. Turn Gas Control Valve To “On” Setting

Restore the pilot light by turning the gas control valve back to its “ON” position once it has been re-ignited. Right now, you should be able to keep your house warm!

Step 9. Relax in Comfort

How did things turn out? If not, when will you get your home warm and comfortable? If your pilot light has been struggling to keep a flame, or if you are still unclear how to fire your pilot light, boiler repair is simply a phone call away! Now that you don’t have to struggle with a cold house anymore, you may turn to a licensed professional with your queries and concerns. To arrange a boiler repair, call or go online to this page. With the help of superTech HVAC Services, you can relight your pilot light in no time.

How Do I Prevent My Pilot Light From Going Out?

Keeping your water heater, furnace, and boiler in good working order can keep those annoying pilot lights from going out on you. An experienced technician will do a maintenance check on the pilot light and thermocouple, as well as clean them both, to ensure that they operate at peak efficiency. Depending on the appliance, a professional will also check all of the connected pipes and wiring, the flue venting, and all other functional aspects of the appliance to verify that each portion is running at peak efficiency.

Maintaining your furnace, water heater, and boiler on a regular basis is essential to ensuring that your heat or hot water never runs out!

Soak Up The Warmth!

That’s all there is to it! A basic description of how to relight your pilot light, as well as the most typical causes for your pilot light to go out is provided. We all know that having no heat or hot water in your house is the worst feeling in the world! The best course of action if you’re having difficulties keeping your pilot light lit or are still unclear about the process is to call a professional.

If you are experiencing any pilot light issues, please don’t hesitate to contact us at (443) 219-7798 or make an appointment onlinehere. We are here to assist you!

Leave a Reply

Your email address will not be published.