How To Restart A Water Heater

How to Reset an Electric Water Heater in Two Easy Steps

Take a look at this. It’s a chilly Monday morning in the Arctic. If your husband hadn’t threatened to suffocate you in your sleep, you would have pushed the snooze button at least a seventh time before you finally got out of bed in the morning. Instead, you sigh heavily, pull the covers back over your head, and go to the restroom. You turn on the shower, wait for the beautiful steam to rise up over the curtain, and then step into the shower with your feet up. But, two milliseconds after you finish soaping up, your pleasant hot shower turns into sleet on the ground.

The hot water is gone bleepity-bleep-bleep, and I have no idea what occurred.

But what about that one?

I’m talking about the one when you’re fumbling around for a towel in an attempt to keep your teeth from chattering?

Why Electric Water Heaters Quit

So, what exactly is the source of Hot-Showerus Interruptus? Alternatively, if you have an electric water heater, it is likely that the unit’s reset button has been activated. Those buttons have a tendency to trip at unpredictable intervals. However, it frequently occurs as a result of the following:

  • The thermostat in the device is not working properly
  • Even the reset button itself isn’t working properly
  • The high-limit switch, which is a component of the unit that prevents water from becoming excessively hot, is no longer operational. There is a short in the heating element. There’s a snag in the wiring someplace

Recall that the reset button on a water heater has a vital function: it interrupts power in the case of a malfunction, such as a power surge or a malfunctioning thermostat, to prevent further damage. If your water heater loses power on a regular basis, it is probable that there is an issue that needs to be repaired by a competent Culpeper County plumbing contractor. Please keep in mind that the combination of electricity and water may be extremely harmful, if not lethal. Never be afraid to bring in a professional to double-check your work.

Assuming you have this understanding, let’s follow through two easy steps to get it back up and running.

First, check your electrical panel.

Locate the circuit labeled “water heater” on your electrical panel (which is normally located in the garage, basement, or storage closet), and turn it on.

  • If the breaker is currently in the OFF position, flip it to the ON position. If it remains in place, you may generally conclude that everything that has happened has been an accident and that you can go about your business as usual. However, if the switch returns to the OFF position, either immediately or shortly thereafter, contact an electrician. If the breaker is currently in the ON position, flip it to the OFF position.

Then, push the water heater reset button(s).

You’ll locate a reset button on the back of your electric water heater somewhere. It is often crimson in color and is generally seen around the thermostat. It might alternatively be concealed behind a detachable metal plate on the device, which would then be concealed behind some insulation. Once you’ve located the button, press and hold it for a few seconds. While you have the access panel off, check to see if there is a second thermostat and a second reset button hidden within.

A professional should be called if the button trips shortly after you press it, indicating that something is not operating properly. If this is the case, the access panel should be replaced, and the necessary circuit breaker should be turned back on.

  • If the electricity to your water heater has been restored, you’re good to go. (Congratulations on your accomplishment!) Just keep in mind that it will take a few hours for the water in the tank to reheat. If your water heater is still not working, turn off the circuit breaker and contact us so that we can figure out what’s wrong and get the hot water flowing again. If your water heater begins to operate but the reset button trips again, turn the breaker back to the OFF position and call us for further assistance. As previously said, your reset button is a safety precaution, therefore if it continually tripping, there is something wrong with your computer.

Is Your Water Heater Trying to Tell You Something?

Taking a cold shower becomes (kind of) amusing all of a sudden. However, when it occurs again, it becomes a source of aggravation. We’d be delighted to come over and see what’s going on, so please contact us right away. You’ve earned some wonderful, hot baths!

How to Reset a Water Heater (and Why You’d Need to)

Please keep in mind that this content may contain affiliate links. This means that, at no additional cost to you, we may gain a small profit on purchases made via our links. Unfortunately, these are quite frequent issues that many homeowners or apartment residents may encounter at some point in their lives, particularly when it comes to electric water heaters and water heater reset switches.

What To Check When You’re Having Hot Water Problems

The first thing you should look for is the water heater’s reset switch, which is normally a red button on the top thermostat of an electric water heater (or on the upper thermostat of a gas water heater) (you will need to remove the small panel to access it). If the button is illuminated, it indicates that the switch has been triggered and must be reset. Pushing the red button on the electric water heater reset button will reset the water heater. On some water heaters, a lower thermostat reset button may also be located on the unit.

If you press one of these buttons and the water heater trips instantly and won’t reset, you may have a problem with one of the components in the water heater.

What’s the Problem? Why Does the Switch Keep Tripping?

One of the most common reasons for the reset switch to trip is because the water heater is allowing the water to become too hot while running. Typically, this is an indicator of an incorrectly functioning thermostat in either the top or lower heating element.

Upper and Lower Heating Elements – How an Electric Water Heater Works

The operation of a water heater is rather straightforward. The water in the pressure tank fills from the bottom up, and it also warms from the bottom up, as shown in the diagram. Fresh water is pumped into the tank from the bottom, where it is heated by the lower heating element. As the water fills the container to the brim, the higher heating element ensures that the water remains hot. Each segment is equipped with a separate heating element and thermostat. These thermostats regulate the temperature of the water heater’s heating components.

The thermostats are activated in order to reheat the water.

If the lower heating element or thermostat fails, the water will not heat up at the bottom of the boiler.

Even if the higher heating element or thermostat fails, you will still have hot water for a short period of time, but you will quickly consume up that hot water before the heated water from the bottom reaches the top.

When a high-limit thermostat is malfunctioning, the element will continue to heat the water over the prescribed temperature, causing the high-limit switch to trigger. the button that resets everything

What is the High-limit Switch?

The high-limit thermostat should be set at a temperature that provides you with good, hot water, but not boiling water that can burn or scald you if you are not careful. The temperature of your tap water should never be higher than that of boiling water. The temperature of the water should never rise over the predetermined setting once you’ve set the thermostat. If this occurs, the high-limit switch will trip, resulting in the higher heating element being turned off completely.

Other Reasons for a Hot Water Heater Reset Button to Trip

Thermostats aren’t the only parts on an electric water heater that may wear out and cause the unit to trip the reset button. This is especially true if you find yourself having to reset the water heater on a regular basis or running out of hot water regularly.

  • The high-limit switch is malfunctioning. If the high-limit switch begins to fail, causing the water to get too hot, the switch will trip. The wiring is a little sloppy. A loose wire in the heating element can generate enough heat to trip the high-limit switch
  • This is known as thermal overload. In the heating element, you have a short circuit. If this occurs, the thermostat may continue to function properly
  • But, the short may continue to heat the water over the appropriate temperature, triggering the high-limit switch. Finally, it is possible that the problem is not with the water heater at all, but with the way the power is set up in your home.

High-limit switches are a common source of malfunctioning equipment. Once a defective high-limit switch begins to cause overheating and boil-over, the switch will trip. Several wires are entangled. When there is a loose wire in the heating element, it can generate enough heat to trip the high-limit switch. In the heating element, you have a short. If this occurs, the thermostat may continue to function properly; but, the short will continue to heat the water over the appropriate temperature, triggering the high-limit switch; and The water heater may not be to blame at all, but rather the way your home’s electrical system is configured.

How to Reset a Water Heater

Article in PDF format Article in PDF format Generally, if your water heater stops providing warm water, restarting the heater will resolve the issue. Simply locate the water heater and locate the reset button, and the process will be straightforward. Nothing more complicated than opening the heater, pressing a button, and closing the heater again. Most of the time, your water should be back to normal within a few hours of the incident. If you find yourself having to reset your water heater on a regular basis, the problem might be connected to a faulty controller or an element that is shorting out.

  1. Step 1: Turn off the electricity to the space heater. If the water heater is still turned on, never interfere with the unit. To begin with, locate and switch off any electricity that may be connected to the heater before you attempt to open it
  • The majority of heaters are connected to the wall through a wire. It is possible that you will need to detach the cable or adjust a knob near it in order to switch off the energy. If your water heater is directly plugged into the circuit breaker box, you’ll need to turn it off there as well.
  • 2 Remove the cover plates from the trays. You should be able to detect a metal plate that is secured to the bottom of your water heater with screws towards the bottom. Remove each screw with a screwdriver, and then carefully take the plate away from the heater with your fingers. Water heaters with two cover plates towards the top frequently include a reset button hidden behind the second cover plate
  • Many of these water heaters are referred to as tankless water heaters.
  • Whether you require a Phillips or a flat head screwdriver is determined by the type of plate you have.
  • Advertisement
  • s3 Remove the insulating pad from the wall. Just inside the heater, there will be a foam installation pad to help with the installation. The buttons that you’ll need to reach in order to reset the heater are hidden below this. Simply remove the pad out of your pocket with your hands and leave it aside for the time being.
  • If there is any moisture on the pad or in the vicinity of the reset button, it is probable that an element gasket is leaking, which will need to be repaired before the water heater can be reset.
  1. 1Find the red reset button on the control panel. In the center of the control panel, there should be a red button to press. There are some instances when this button is actually labeled as the “reset” button
  2. 2 Firmly press the button to activate it. The reset button might become stuck from time to time, especially if you haven’t reset the heater in a long period of time. In order for the reset button to push inward, you must apply tremendous pressure with your fingertips. Wait for the sound of the button clicking. Most of the time, a click signifies that the heater has been effectively reset. Keep your finger held against the button until you hear a clicking noise
  3. Then release your finger.
  • If you don’t hear a click when you press the button, or if the button pops straight back out, inspect all of the heater’s wiring for nicks or loose wire nuts and replace them as necessary. If the wiring is in good condition, the controller is most likely in need of replacement
  • Every heater is different. When you press the reset button on certain heaters, you may not hear a click. If you do not hear a click even after pressing on the button for about five seconds, you should reassemble the heater regardless of the situation. It’s likely that it will still work to restore hot water.
  1. 1Reinstall the insulating pad in its original location. Take the insulating pad that you removed previously and place it in a safe place. 2Reinstall it in the heater in the same location where you removed it previously, using your hands
  2. 3reinstall the door by screwing it back into place. Replacing the door over the control panel is simple. 3. Replace the screw in its original location and re-energize the system. Reconnecting the wire or flipping the required switch will restore power to the system. Within a few hours, your water should be back up and flowing as normal. Advertisement

Inquire about something There are 200 characters remaining. Include your email address so that you may be notified when this question has been resolved. SubmitAdvertisement Thank you for submitting a suggestion for consideration!

  • If you are unable to figure out how to turn off the electricity, you need get expert assistance to reset the water heater. Attempting to tamper with a water heater while it is still operational is exceedingly risky.

Advertisement

About This Article

If your water heater suddenly stops providing warm water, resetting it is generally sufficient to resolve the issue. First and foremost, turn off the energy to your heater. Then, using a screwdriver, carefully remove the cover plate from the front of your heater. Some heaters are equipped with a second plate that covers the reset button. Then push and hold the reset button while removing the foam insulation pad that was underneath the plate. A click should be heard on the majority of water heaters when they are reset.

Continue reading for additional information, including how to unplug your water heater if it is directly connected to the electrical system. Did you find this overview to be helpful? It took 78,603 readers to read this page. We appreciate you taking the time to write it!

Did this article help you?

When the hotwater heater in your home fails, duties such as showering, doing laundry, cleaning dishes, and other household chores come to a grinding halt. If you have a gas-powered hot water heater, it is possible that the pilot light has gone out, which is the root cause of the problem. In most circumstances, if you relight the pilot, you should be able to go back into the air again. In this post, we’ll demonstrate how simple it is to complete the task yourself.

See also:  Where Is The Water Filter On A Whirlpool Side-By-Side Refrigerator?

What does the pilot light do?

The pilot light of your gas hot water heater is a tiny, continuously burning flame that serves to start the burner of the appliance. To put it another way, if the pilot light goes out, the unit will be unable to heat water. It is possible for a pilot light to be extinguished for a variety of causes, including something as simple as a short stoppage in the gas line or an air bubble in the gas line. Warning: If you smell gas at any stage throughout the process, leave the area immediately and contact your energy supplier as soon as possible.

Steps to relight the pilot light.

  1. Remove your foot from the gas pedal. Find the gas shut-off valve on your hot water heater and turn it off. The knob should be labeled in a clear and understandable manner. Turn the switch to the “Off” position and wait 5-10 minutes to ensure that all of the gas has been expelled. Locate the pilot light access point. Most of the time, this will be under the gas valve. To locate the burner and two gas tubes, open the pilot cover (if one is present) and use a flashlight to peer inside the hole to locate the burner and two gas tubes
  2. Return to the gas valve and turn the knob to the “Pilot” position. By depressing the knob all the way down, you will begin to feed gas to the pilot. There are certain hot water heaters that include a separate pilot button
  3. If this is the case, press that instead. While maintaining control of the knob or button, reach into the access and ignite the pilot with an extended lighter while still keeping it down. Once the pilot light comes on, keep the knob/button down for about one minute. Release the knob/button carefully after that period of time, and make sure that there is still a flame emanating from the pilot. Return to the gas valve and turn the knob to the “On” position. Typically, a noise will be heard to indicate that the primary burner is lighting
  4. After giving the heater enough time to restart, replace the access cover and inspect the hot water supply.

What happens if the pilot light goes out again?

The fact that the pilot won’t light or that it keeps going out is a clue that you may be experiencing another problem with your hot water heating system. The most typical issue we encounter is a thermocouple that is twisted, fractured, or filthy (also called a flame sensor). Because the typical service life of a hot water heater is 12-15 years, it may be a wiser investment in some situations to replace the unit rather than spend money fixing your existing unit. if your water heater isn’t producing enough heat, call Reidelt Plumbing Inc.

Our professional plumbers will come out to your home, assess the situation, and provide recommendations on how to restore hot water flow in your home.

  • You may be experiencing another problem with your hot water heater if the pilot refuses to light or if it continues to go out on its own. Broken, damaged, or unclean thermocouples are the most typical issues we see (also called a flame sensor). Because the typical service life of a hot water heater is 12-15 years, it may be a wiser investment in some situations to replace the unit rather than spend money fixing your existing one. Please contact Reidelt Plumbing Inc. at (219) 322-4906 if your water heater isn’t producing enough heat. Our professional plumbers will come out to your house, assess the situation, and make recommendations on how to restore hot water flow.

How to Reset a Water Heater

Being without a functional hot water heater throughout the winter is quite painful. What should you do if your hot water heater is not functioning properly? Often, rebooting the system is all that is required to solve the problem. Depending on the type of water heater you have, you may choose from one of the following approaches to resolve your issue (gas, electric, or eventankless).

How to Reset an Electric Water Heater

The switch was tripped, which caused the problem, and it only requires a reset to correct it. If you do not know how to reset a water heater, it is a very simple procedure to learn. All that is required is a little know-how; no special skills are required. The reset button should be the first thing you search for!

Where Is the Water Heater Reset Button?

How well do you know the location of your water heater (attic, garage, basement)? Having identified the water heater, look for a reset button on the higher thermostat, which is normally placed on the back of the unit. If it isn’t visible, it is most likely located someplace in the lower portion of the water heater. Some devices have a button at each position, whereas others do not. If you want further assistance, watch this informativeHomeowner Repair video.

Reset Button on Water Heater Doesn’t Click

So, what should you do if the water heater’s reset button does not function properly? It’s possible that your thermostat is malfunctioning. If the hot water heater continues tripping the reset button, the high limit switch may be the source of the problem. What’s going on is that the thermostat isn’t correctly controlling the temperature. When a defective thermostat enables the temperature to rise to an unsafe level, the high limit switch is activated. Obviously, you don’t want your child to wash his or her hands in hot water, thus this function is essential.

The switch will continue to be tripped until you purchase a replacement thermostat. It’s also conceivable that you have a grounded element in your system, which is causing the water to boil up. Learn how to test the element of a water heater.

Other Causes of the Issue

A malfunctioning thermostat is the most prevalent source of this problem, but it is not the only one. It’s conceivable that your wiring is faulty or has been corrupted in some other manner. It’s also possible that you have a short in one or both of the heating components. Finally, but certainly not least, it’s possible that you’re experiencing electrical difficulties with your home as a whole, and that the problem isn’t limited to the water heater.

How to Reset a Gas Water Heater

Relight the water heater pilot, and on newer types, there is a thermal switch that may be used to reset the water heater.

How Long for Hot Water Heater to Heat After Reset?

It is necessary to wait for hot water once you have reset the system (unless you have an on-demand water heater), but how long should you wait? It varies depending on the size of the tank, but with any unit, you should be able to get into a hot shower in 30-40 minutes with gas water heaters and 60-90 minutes with electric water heaters, depending on the size of the tank.

How to Reset Tankless Water Heater

Thermal safety reset capabilities are also included in on-demand systems. You can almost certainly count on having to remove the cover of your tankless water heater in order to have access to it if you need to reset it. Because each manufacturer will have their unique set of instructions, we recommend that you get out your owner’s manual to handle this issue.

Turn to the Plumbing Experts

Thank you for taking the time to visit us here at PlumbersStock.com. Please do not hesitate to contact us if you have any more questions regarding your project or related items. Remember, we carry only the most reputable brands in the industry, like Bradford White, Takagi, Stiebel Eltron, and others. Purchase water heater components and accessories at a discount from many sources. Resources that are related to this topic include: How to Light a Hot Water Heater (with Pictures) How to Turn Off a Water Heater (with Pictures) Instructions on How to Drain a Water Heater Using a Water Heater for the First Time How to Increase the Temperature of a Water Heater Is there a recommended temperature for the water heater?

How to Reset an Electric Hot Water Heater

After the water heater’s electricity has been turned off, remove the metal plate that covers the thermostat by removing the two screws that hold it in place. Keep the screws in a safe place. There will very certainly be some sort of insulating layer underneath the plate. You should be able to see the reset button when you have removed the insulation. It’s most likely in the color red, and it could even be labeled “reset button” or something like. Firmly press the button in to secure it. This should cause the electricity to the heating element to be re-established.

Next, depending on how you shut down the electricity, either reconnect the plug to the socket or reset the circuit breaker to the “ON” position.

Step 3. Check to See if the Issue is Solved.

Using the two screws provided, remove the metal plate covering the thermostat after the water heater’s electricity has been turned off and turned off again. Keep the screws in their original locations. A layer of insulation will most likely be present behind the plate. The reset button should be visible once all of the insulation is removed. Perhaps the button is red, and it may even have the word “reset” written on it. The button should be pushed in all of the way. Resetting the heating element’s electrical connection should do the trick.

Replacing the insulation is simple; just remember to use the screws you saved to secure the metal plate. Finally, depending on how you shut down the electricity, either reconnect the plug to the socket or reset the circuit breaker to the “ON” setting.

How to Light the Pilot for a Gas Hot Water Heater

When the water in the tank needs to be heated, tank-type gas water heaters utilize a pilot light to ignite the gas burner, which then heats the water. The cold water flowing from the hot water tap is usually the first sign that your pilot light has gone out, so keep an eye out for it. Even if the equipment is not malfunctioning, a pilot light might go out for a variety of causes, including sudden swings in gas main pressure. If the pilot light on your heater goes out, you may relight it by yourself.

1.

  • Find the gas regulator valve on the water heater and turn it on. It is positioned on the exterior of the water heater, near where the gas line enters the device, and it is controlled by a knob on the outside. The gas supply to the pilot burner beneath the hot water tank is controlled by this valve. To turn the valve off, turn the knob all the way to the left. Wait five minutes before continuing. Locate the pilot burner, which is located beneath the natural gas water heater. Remove or unsnap any access cover that is preventing you from getting to the burner. Make use of the flashlight to illuminate the pilot burner

2.

  • Turn the knob on the gas regulator valve to “Pilot,” press down on it, and keep it pressed down. The flow of gas to the pilot burner is initiated by pressing this button. To start the pilot burner gas flow on some water heater types, you must push and hold down a separate red button for a period of time. Find a red or black button labeled “Ignition” on the top or side of the gas valve if your heater has a piezoelectric spark pilot igniter built in. To start the pilot, press the button on the control panel. As the igniter ignites, you will hear a click sound. If you must manually ignite your heater, a long-necked barbeque lighter is the most secure type of lighter to use. Light the pilot burner with a lighter flame and turn it on.

3.

After the pilot has been ignited, keep the regulator valve knob firmly depressed for at least one minute. This permits the pilot flame to heat the thermocouple safety sensor, which detects the presence of a live pilot flame, allowing the pilot flame to heat the sensor. Reduce the pressure on the regulator valve knob gradually. When the pilot light continues to glow after you have released the knob, turn the knob to the “On” position. During the ignition of the primary burner, you should hear a muffled “whoomp” sound.

Things You Will Need

Look for a label on your gas water heater that provides particular pilot lighting instructions for the model of water heater you have installed.

Warning

  1. If you smell gas in the vicinity, it is not a good idea to attempt to relight a water heater pilot light (or to do any other maintenance on the device). When you are outside the home, dial 9-1-1.

Why Your Water Heater’s Pilot Light Keeps Going Out & How to Fix It

The date is May 13, 2021. When the pilot light flame on your gas water heater goes out, it is an annoying and frustrating situation to have to deal with. When your water heater’s pilot light fails to stay lit, you’re left without hot water, which makes even the most basic of tasks such as taking a shower a chore. Naturally, you question, “How did this happen? What happened?” Is there anything you can recommend to help you get things going again? What should I do to have it repaired? “May you tell me about the costs I can expect?” Fortunately, if your water heater pilot light goes out, you should be aware that this is a frequent problem that many homeowners have and that the time and effort required to repair it is low.

Why does the pilot light on my water heater keep going out?

Because of problems with the heater’s thermocouple or owing to access to combustible air, your water heater’s pilot light continues going out repeatedly.

Thermocouple Issues

When your pilot light is on, your thermocouple detects the presence of the flame. The thermocouple’s tip is positioned above the pilot flame, providing a voltage that maintains the gas valve open in the process. A thermocouple will shut down the gas supply to your water heater if it detects that the pilot light on your water heater is not lighting up properly. When thermocouples are exposed to moisture or dust for an extended period of time, they might malfunction, gather dust, or get bent away from the pilot light’s flame.

See also:  How To Change Whirlpool Fridge Water Filter

Lack of Combustible Air

Another reason why your gas water heaterpilot light won’t remain lighted might be that there isn’t enough combustible air in the room where it is located. To keep the pilot light on in your water heater, you’ll need to blow air into it.

Otherwise, the flame will be extinguished. Take precautionary measures to ensure that the water heater is not surrounded by material, such as litter or lint, which might increase the quantity of combustible air present. Maintain as much cleanliness as possible in the surrounding region.

What do I do if my water heater pilot light keeps going out?

Try to rekindle the spark on your own first, if at all possible. Take the following general steps:

  1. Locate the gas shut-off knob and turn it all the way to the “Off” position. The gas flow is halted as a result of this. Allow for a few minutes for the gas to dissipate before continuing. To get access to the burner, remove the access panel. To begin the flow of gas, turn the knob to the “Pilot” position. You’ll want to press and hold the knob down for a few seconds. While still holding the gas knob, ignite the pilot with a long lighter while still holding the gas knob. To ignite your gas water heater, use the button on the side of the tank that says “ignite.” As soon as the flames have been extinguished, turn the gas knob to the “On” position and wait for the main burner to come on.

If you are unable to relight the pilot or if your pilot light keeps going out, it is possible that you have another problem, such as a faulty thermocouple, to consider. Please refer to the owner’s handbook for your water heater equipment for further information.

Can I replace a thermocouple myself?

It’s possible that you have a defective thermocouple if you can’t relight the pilot or if your pilot light continues going out despite your efforts. Note: Consult the owner’s handbook for your water heater device.

Call BGE HOME

Please contact BGE HOME at (410) 918-5600 if your water heater pilot light will not light or continues going out. You may also contact us online. Our licensed specialists are available 24 hours a day, seven days a week to come out and inspect your water heater and make recommendations on how to get it running safely and effectively again. This item was posted on Thursday, May 13th, 2021 at 4:09 pm and is filed under Uncategorized. Commenting and pinging are temporarily closed for this post.

How to Relight Your Water Heater Pilot Light (For Every Major Brand!)

The pilot light on your hot water heater has great influence on your life. Anyone who has walked into their shower on a frigid winter morning, with their body freezing and their teeth chattering as they wait for hot water that never arrives, knows what I’m talking about. In the case of a natural gas water heater, this might indicate one of two problems. There are two possibilities: either (1) the gas supply has been switched off or (2) your pilot light has gone out. We should first address the likelihood that your gas supply has been interrupted (and as fast as possible).

1. How to Make Sure Your Gas Supply is On

  1. Locate the shut-off valve for your natural gas line
  2. It is common to find the shut-off valve near to your gas meter (as shown in the figure below), which is often positioned on the side or front of your home or major structure. Check to be that the shut-off valve attached to your gas line is in the “ON” position before proceeding. If it is not in the ON position, the problem is not with your gas line
  3. However, if it is, the problem is with your gas line. If the valve is currently in the OFF position, switch it to the ON position. Please do not hesitate to contact your local gas company for assistance.

Examining your gas line is the first step in determining whether or not you have a lack of hot water. Double-check to see that the gas shut-off valve is in the “ON” position. If everything is in working order with your gas supply, it’s time to check the pilot light on your water heater.

2. How to Light Your Pilot Light Water Heater

Depending on the manufacturer, re-igniting a pilot light may need a different procedure. Fortunately, there are just a few number of producers. The first step should be to check for the installation instructions, which are normally fastened to the water heater. Don’t be concerned if you can’t locate them. Specific brand-by-brand instructions are provided in the section below. Instructions in this video are “generalized,” as the title indicates. Scroll down to the bottom of this page for instructions unique to your brand of water heater.

How to Light a Rheem Hot Water Heater Pilot Light

The pilot light on an ARheem water heater must be manually activated by striking thepiezo ignitor striker that is incorporated within the water heater.

  1. Using a clockwise motion, turn the gas knob on your Rheem water heater until it is at the desired position
  2. Counter-clockwise turn the temperature dial on the water heater until it is set to the lowest temperature setting. Wait five minutes to let any gas in the water to pass through
  3. Remove the outer door of your Rheem water heater from its mounting bracket. Counter-clockwise turn the gas knob to the “Pilot Light” setting until it is in this position. Press the red button to the left of the gas knob until it becomes depressed. The piezo ignitor striker is located on the left side of the gas knob. While maintaining pressure on the red button, continually push the piezo ignitor striker until the pilot light is re-lit until the problem is resolved. Through the viewing glass on the inside of the Rheem water heater’s inner door, you can see the pilot light. After the pilot light has been turned on, continue to hold down the red button for one minute before releasing it completely. The pilot light will remain on during the process. Remove and reattach the outer door of your water heater
  4. To turn on the gas, turn the knob to the “ON” position. Set the hot water temperature slider to the temperature that you desire for your water

How to Light an A.O. Smith or State Water Heater Pilot Light

AO Smith water heaters andState water heaters, including the Conservationist model, are equipped with a piezoelectric igniter mechanism that lets you to light the pilot by pressing the ignition button on the water heater.

  1. Disconnect the access panel from the side of the A.O. Smith or State water heater and place it somewhere out of the way
  2. To turn off the gas supply, turn the control knob on the water heater’s side to the “OFF” position and let the room air out for roughly 10 minutes. The “Pilot Light” setting on the gas control knob should be selected. The red button should be pressed down (this will allow the gas to flow to the burner assembly)
  3. And While maintaining pressure on the red button, press down on the ignitor button until the pilot light illuminates. It is possible that you may have to press down on the ignitor button two or three times before the hot water heater pilot light turns back on. Continue to hold down the red button for approximately 60 seconds after the pilot is lighted, then gently release the button. Make sure the gas is turned on by turning the control knob to “ON.” Replacing the access panel on the side of the water heater is necessary.

How to Light a Bradford White Water Heater Pilot Light

  1. Disconnect the access panel from the side of the A.O. Smith or State water heater and place it somewhere out of the way. To turn off the gas supply, turn the control knob on the water heater’s side to the “OFF” position and allow the room to cool for roughly 10 minutes. The “Pilot Light” setting on the gas control knob is selected. Continue to press down on the red button, allowing for a steady supply of gas to reach the burner assembly. In the meantime, keep holding down the red button and pressing down on the ignitor button until the pilot light illuminates. Before the hot water heater pilot light turns back on, you may need to press down on the ignitor button two or three times. After the pilot is lighted, hold the red button down for approximately 60 seconds before carefully releasing the button. Set the gas control knob to the “ON” position
  2. Turn on the gas. Reinstall the access panel on the side of the water heater
  3. And

Resources

  • Precautions to take when using a water heater
  • How to get hot water back from your water heater
  • The components of a water heater
  • Water heater maintenance and repairs
  • What is the average lifespan of a water heater?

Call 1-Tom-Plumber

It might be rather frightening to experiment with the gas in your house. Don’t be concerned, we’ll have you back in a warm shower in no time!

Please do not hesitate to contact us or call 1-Tom-Plumber (1-866-758-6237). Regardless of the nature of the emergency plumbing, drainage cleaning and drain clearing, or water damage situation, we will respond quickly. This includes excavation of subterranean water pipes and sewage main lines.

How to Reset a State Water Heater

Investigate the cause of your State water heater’s thermal switch being triggered by performing troubleshooting steps. Remove any lint that has gathered on the sides and top of your appliance by wiping it down with a damp cloth. Open a window or door in the area where your water heater is located to allow more air to circulate around the device and cool it. Contact State customer care to book a repair appointment if your State water heater is still having difficulties after being reset to factory settings.

State water heaters are equipped with a safety switch known as a thermal or high-limit temperature switch, which turns off the supply of electricity to the heating elements of your appliance when the water temperature rises over 170 degrees Fahrenheit.

Instead, follow these steps.

Step 1

Unplug the water heater’s electrical supply from the mains power source. Before continuing, make certain that all electricity to your water heater has been turned off.

Step 2

The control circuit panel for your State water heater may be found here. The control circuit panel for the majority of State water heater types is a rectangular metal box that is located on the side of the water heater, as seen below.

Step 3

Use a screwdriver to pry up the control circuit panel door and remove the two screws that hold it in place. Maintain your distance from the control circuit panel door and screws until you have completed resetting your water heater.

Step 4

Remove the protection pad and insulating block from the control circuit panel of your State water heater to uncover the safety controls for your water heater. Place the pad and insulating block aside until you’re ready to replace them with new ones.

Step 5

To reset your State water heater’s control circuit panel, look for a large red button labeled “Reset” in the center of the panel. To manually reset your water heater, push down on the “Reset” button for a long period of time. The time it takes for your water heater to return to normal performance once it has been reset can vary between 12 and 24 hours depending on how old it is.

Step 6

Replacing the insulating block and protection pad in the control circuit panel of your State water heater is simple. Replace the control circuit panel door, insert the screws, and tighten the screws to secure the door in place on the control circuit panel. Once you’ve completed the process of resetting your water heater, turn on the energy to the device.

How to Reset Your Water Heater (5 Simple Steps)

Is it frustrating to be daydreaming about a nice shower after an exhausting day at work and discover that there is no hot water when you reach home? Something is definitely wrong if the water suddenly becomes ice cold or simply refuses to heat up at all. In such situations, knowing how to restart your water heater is critical to your safety.

Unfortunately, it is not a tough task, and we will walk you through each stage of the process. A little bit about the reasons for performing a reset as well as some items to keep an eye on will also be discussed.

How to Reset a Water Heater

After a hard day at work, do you crave for a nice shower, but when you arrive home, there is no hot water to be found? Something is definitely wrong if the water suddenly becomes ice cold or refuses to heat up. In such cases, knowing how to restart your water heater is critical. Fortunately, it’s not a tough task, and we’ll walk you through each stage of the process. A brief explanation of the reasons for doing a reset as well as potential issues will be provided.

1.Disconnect the Unit

After a hard day at work, you’re looking forward to a hot shower, but when you arrive home, there’s no hot water? Something is definitely wrong if the water suddenly becomes ice cold or refuses to heat up at all. In such situations, knowing how to restart your water heater is critical. Because it is not a tough process, we will guide you through each step. As a bonus, we’ll explain why you might need to execute a reset and what to look out for.

2.Locate and Remove Cover Plate

This procedure will necessitate the use of a screwdriver. Determine if you require a Phillips or a flat head screwdriver by consulting your owner’s handbook. Next, take a check around your water heater to see if there is a detachable plate somewhere. It’s most likely going to be located in the front of the device and secured in place with at least two screws. Identify it and remove the screws after you’ve located it. Keep an eye on the plate, since it may fall to the floor or onto your foot. Lift the plate away from the wall once the screws have been removed.

3.Take out the Insulation

An insulating material should be installed beneath the cover plate as a precaution. It’s commonly a foam pad that’s placed over the buttons that need to be pressed to reset the machine. Remove this from the equation and set it aside for the time being. Keep an eye out for any signs of moisture. If you see any moisture around the reset button or on the pad, it is possible that there is a leak in the rubber gasket. This must be addressed prior to attempting to reset your water heater.

See also:  How Long Does It Take For A 30 Gallon Water Heater To Heat Up

4.Click the Reset Button

The reset button is most likely a red button in the centre of the control board, which you may press to restart the computer. On some water heaters, the “reset button” is clearly labeled for ease of use. You can proceed to reset the device if the reset button is protruding, which indicates that it has been triggered. If it isn’t illuminated, it is most likely due to another problem. The majority of the time, it’s a malfunctioning control board. The button must be pressed firmly in order to be forced inward.

If, on the other hand, there is no clicking sound when you press the button, don’t be alarmed.

You should be able to find out from your owner’s handbook whether you should or should not wait for the click.

If your company has one, make use of it as well.

If the switch continues to trip (i.e., does not reset), contact a professional for assistance. The switch serves as a safety precaution. Its purpose is to shut down the unit in the event of an overheating situation or similar safety hazard (1).

5.Reassemble and Turn On

You may now reassemble your water heater and prepare for a hot shower because your water heater has been successfully reset. Replace the insulating pad as a starting point. It should be positioned so that it covers the reset button and the majority of the control panel space. After that, reinstall the cover plate with a screw to secure it in place. Manually spin both screws a couple of times once they have been inserted. Using the screwdriver to finish tightening the screws will prevent the plate from sliding around.

Start by turning on your water heater and waiting for the hot water to arrive.

It is possible to receive a painful electric shock if you do so.

Why Do I Need to Reset?

A circuit breaker and a reset button are incorporated to prevent a potentially dangerous scenario from arising. In many cases, the reset button will just trip without any apparent reason, and it is safe to press the button again. However, there are a few significant reasons why it could trip and refuse to switch back on again:

  • Several safety features are implemented to keep a potentially dangerous scenario from occurring. Sometimes the reset button will suddenly trip without any apparent reason, and it is perfectly safe to reset the device. However, there are a couple of significant reasons why it could trip and refuse to turn back on again:

Keep it Safe

The reset button is included for safety reasons, in order to prevent boiling water or damage to the machine. Fortunately, resetting is straightforward and can be completed in a matter of minutes. If, on the other hand, the button will not reset, contact a specialist because this might suggest a more serious problem. Knowing how to reset a water heater is crucial, and we hope that the information provided above was of use. Any more inquiries can be left in the comments section below if you have any further concerns.

Help

  • Product Support
  • Locate a Service Provider
  • Check the Status of Your Warranty
  • Contact Us

Back This is a continuation of the stages taken before. If you started from this point, please review the preceding steps to make sure you’ve taken all necessary safety precautions. It is recommended that you read the printed instructions that came with your water heater in addition to the material on this web site. Read and observe any warning labels on the water heater, as well as the safety recommendations in the printed owner’s handbook, to limit the danger of property damage, serious injury, or death.

Step1:Reset the Thermal Switch

It is possible for the thermal switch to trip if the water heater is not receiving enough air.

  • If the water heater does not receive enough air, the thermal switch may trip. To reset the thermal switch, press the little reset button located in the center of the switch. Depending on how badly it’s tripped, you might be able to hear it click. However, if the thermal switch does not make a clicking sound, you should attempt to ignite a pilot using the directions on the water heater’s label. If the Status Light begins to flash now, it is likely that the thermal switch has triggered. This indicates that the water heater is not receiving sufficient airflow. Replace the outer door with a new one. If this is a first-time installation, refer to A draft test is being carried out. If the water heater is more than a few years old, it is possible that the air filter or flame arrestor has become clogged with dust or lint. See Air Filter and Flame Arrestor should be cleaned regularly. Turn off the gas control knob and the gas supply valve, and then click on “More Help” below if the Status Light continues to not flash.

How to Fix a Water Heater Pilot Light

Time Approximately one hour or less Complexity Cost for a beginner is less than $20.

Introduction

If your hot water heater suddenly stops operating, it’s likely that a faulty thermocouple has caused the gas to the pilot light to be turned off. Replacement is a simple do-it-yourself project.

Tools Required

Is there no hot water? If you have a natural gas or propane water heater, there is a good probability that the pilot light has gone out. It is this little flame that starts the gas burner on your water heater that is referred to as the pilot light. When the pilot light on your water heater goes out, the first thing you should do is try to relight it by following the instructions on the water heater label. The thermocouple is by far the most prevalent cause of pilot failure, whether it occurs immediately after lighting or on a regular basis after the pilot has been extinguished.

If you do not wait for a professional to arrive, you will be able to get your hot water running without incurring the expense of a service visit. Continue reading to find out how to start a pilot light.

What is a Thermocouple?

  • What if there’s no running water? A natural or propane gas water heater’s pilot light is most likely out if you have one of these appliances. This little flame serves to start the gas burner in your water heater, which is controlled by the pilot light. If you notice that the pilot light on your water heater has gone out, try to relight it by following the instructions on the water heater’s label. The thermocouple is by far the most prevalent cause of pilot failure, whether it occurs immediately after lighting or on a regular basis after the pilot has been ignited. Fortunately, most thermocouples can be replaced for a low cost and in less than an hour, which is a welcome relief. If you do not wait for a professional to arrive, you will be able to get your hot water running without incurring the expense of a call. To discover how to light a pilot light, continue reading this article.

Project step-by-step (6)

  • Shut off the gas line by closing the cutoff valve. As seen in this photo, turn the valve a quarter turn so that the handle is at a right angle to the pipe.

Unscrew the Nuts

  • Turn off the control valve if it is on. Remove the burner access covers and loosen the bolts on the gas, pilot, and thermocouple lines to free up the burner.

Sign Up For Our Newsletter

Complete your do-it-yourself tasks like an expert! Become a subscriber to our newsletter! Do It Right the First Time, and Do It Yourself! Step number three.

Remove the Assembly

  • Remove the water heater pilot light burner component from the water heater. Remove the old thermocouple by unscrewing or pulling it out. Purchase a new one that is the same size and length as the previous one

Install the New Thermocouple

  • Install the new thermocouple in the same manner as the previous one
  • Replace the burner assembly by sliding it back in. Reattach the three wires to the control valve where they were disconnected.

Reattach the Lines to the Gas Valve

  • The three lines must be reconnected to the gas valve by threading the nuts into position with your fingers and hand-tightening them
  • A quarter- to half-turn of the wrench tightens them up.
  • The three lines must be reconnected to the gas valve by threading the nuts into position with your fingers and hand-tightening them. Using a wrench, tighten them up to a quarter to half turn

Test for Gas Leaks

  • Keep in mind that in order to test for leaks, the pilot light must be lighted and the burner turned on so that gas flows through the big tube.
  • Replenish the water supply by opening the shutdown valve and lighting the pilot light. Turn the control valve to the “on” position. Use a 50/50 mixture of dish soap and water to check the screw joints for air bubbles, which indicate a leak, while the gas burner is turned on.
  • Keep in mind that when the water heater pilot light is re-ignited, the flame should wrap around the thermocouple bulb.

CAUTION!

During this procedure, you should not be able to detect the scent of gas (except for a slight whiff when you remove the gas lines). If you find yourself in this situation, exit the house immediately and contact your gas provider.

WhenNotto Replace the Thermocouple

Some gas water heaters have a burner chamber that is “closed,” making it impossible to reach the burner. It is recommended that you contact a professional to repair this sort of heater. In addition, some gas water heaters are not equipped with pilot lights. Allow the professionals to take care of this as well.

How to Restart the Pilot on a Rheemglas Fury Water Heater

Residential gas water heaters from Home-DiyRheem, including the Fury Direct Vent Series, are available for purchase online. These warmers are gas-powered and are available in sizes ranging from 40 to 50 gallons. Aside from that, they make use of Rheemglas tank liners, which the company claims helps to resist corrosion and hence increases the lifespan of the water heater. The gas supply will be shut off if your pilot light goes out due to a malfunction of the safety system in your heater, which will avoid a buildup of gas in your house.

Tip

Continue with steps 2-7 if the pilot does not ignite or does not go out immediately. If the pilot light does not stay lit after many tries, switch off the water heater and contact a service expert for assistance.

Warning

It is not recommended to attempt to relight the water heater if you continue to smell gas after you have shut off the water heater. You should open some windows and notify the gas company or the fire department if you smell gas. You should also leave the home immediately if you smell gas. Gas leaks are potentially hazardous and can result in home explosions.

  1. Discover where to find the water heater’s thermostat and pilot ignition, which will be on the front of the water heater, at the bottom. Make sure that the thermostat dial is turned counterclockwise until the pilot lighting setting is reached. To turn on the gas, turn the gas control knob, which is located on the top left side of the metal box to which the thermostat dial is attached, to the on position. Turn the thermostat dial to the off position while keeping the gas control knob pushed. Wait for five minutes. The waiting period is important to let any gas that has accumulated to be released. Removing the outer door of the water heater, which is positioned at the base of the heater, is necessary. You will be able to slide it up and out of the way to remove it. Make a counterclockwise rotation of the gas control knob until it is in the pilot position. Push the gas control knob all the way down until it is completely depressed, and then hit the piezo-electric spark generator button, which is situated directly to the right of the gas control knob, as quickly as possible. It is possible that you will have to push the piezoelectric spark generator button numerous times before the pilot will start. When you peek through the glass pane on the inside of the water heater’s inner door, you’ll notice that the pilot light is on
  2. This indicates that the water heater is operational. Continue to push down on the gas control knob for roughly 1 minute. Otherwise, the pilot will be forced to leave the aircraft. Replace the outer door, crank the gas control knob on the water heater until it is in the on position, and then adjust the thermostat to the appropriate temperature setting

The Drip Cap

  • A maker of domestic gas water heaters, Rheem produces the Fury Direct Vent Series, which is a popular choice among homeowners. Discover where to find the water heater’s thermostat and pilot ignition, which will be on the front of the water heater, at the bottom. Make a counterclockwise rotation of the gas control knob until it is in the pilot position.

Is Your Water Heater’s Reset Button Continuously Tripping

Showering, doing laundry, and cleaning dishes, to mention a few activities, are all made easier by the availability of hot water in our homes. So, what should you do if the reset button on your water heater is constantly tripping? When this occurs for the first time, remove the top panel from the water heater. You will find a red reset button on the inside of the thermostat, which you should press to reset it. The thermostat should be changed if the button continues to trip after you have completed this procedure.

This implies that the thermostats are malfunctioning or are on their way to malfunctioning.

Call an Orlando plumbing professional to replace the thermostats if your heater is constantly blowing a blown fuse.

Which are fitted into the tank and are responsible for the actual heating of the water.

It is possible that spending money to fix an outdated water heater can wind up costing you more money in the long run.

This is why these mechanisms have been put on your water heater to prevent this from happening.

Alternatively, tampering with the safety systems in order to attempt to repair the water heater might be a fatal mistake.

Reseting the Water Heater We also serve the communities of Longwood, Lake Mary, Winter Park, Casselberry, Orlando, Apopka, Maitland, Deltona, Altamonte Springs, Oviedo, Sanford, Winter Springs,Deland, and Daytona Beach, as well as the whole state of Florida’s Central region.

Leave a Reply

Your email address will not be published.