How To Change Whole House Water Filter

7 Steps to Change Whole House Water Filter

The entire home water filter, like all other appliances, has to be checked from time to time for efficiency. Changing your cartridge on a regular basis is an excellent approach to ensure that it remains in good working order at all times. Nevertheless, the most important question is: how do you update your water filters? In addition, how frequently do they need to be replaced? When you fail to replace them, what will be the ramifications? In this post, we’ll go through how to change the entire home water filter and give you some helpful tips.

What Are Whole House Water Filters?

Whole-house water filters are specialized water filtration systems that filter water from all of the outlets in a home’s plumbing system and appliances. As a result of their installation in the main water supply, these devices ensure that every other faucet in the building may dispense safe drinking water. The faucet water filter is a less expensive alternative to a whole-house water filtration system. This, on the other hand, is mounted on each faucet and filters only the water that comes from those specific outlets.

The AGravity filter is ideal for use on your counter top.

How to Change Whole House Water Filter

The procedures outlined here will walk you through the process of changing the entire home water filter. Make certain, however, that you are wearing protective gloves and goggles to prevent water splashes from entering into your eyes. When changing a whole-house water filter, you will also need an empty bucket to work with. Make sure the bucket is placed underneath the water filter unit to prevent water from spilling on the ground.

Step 1: Turn Off Water Supply and Release Pressure

First, make certain that the water supply has been entirely shut off at the valve or main water feed. Pushing the red knob will relieve the pressure. Make careful to pay attention when you press the pressure release knob, since water will spew out.

Step 2: Take out Casing and Tidy up O-Ring

Remove the case by unscrewing it and removing the large O-ring. The O-ring has a big diameter and is attached to the casing by a little black plastic band, which you will discover within the casing when you open it. Remove the ring from its original location and clean it well. If it has deteriorated to the point of becoming dangerous, replace it.

Step 3: Throw Old Filter Away and Tidy Up Housing

Remove the old water filter and dispose of it in an appropriate manner. After you have completed this, the following step will be to clean the casing by removing any debris that has accumulated inside of it. After that, wash the casing with warm water, household soap, and a soft cloth or sponge to remove any remaining dirt. After that, fill the housing with about a third of the water it holds and add a little bit of bleach to it before washing it. Washing the case gently and carefully is recommended to avoid causing any harm to the product.

Step 4: Apply Lubricant to O-Ring

Clean silicone grease should be used to lubricate the O-ring in order to ensure that it sits correctly in the casing of the device.

Because silicone oil does not cause the rubber to soften or swell, it is extremely necessary to apply silicone grease. Return the O-ring to its groove on the ring. When installing the O-ring, take care not to overtighten it, as this might cause the housing seal to break.

Step 5: Buy and Install a Brand New Water Filter Cartridge

Replace the water filter with a new one. Whether you opt to purchase a reverse osmosis system or any other type of water filter, make sure to inspect the housing to ensure that there is a standpipe in the centre of the housing. It is in the shape of a round gadget with a short rubber pipe extending from the top. It is critical that the filter be appropriately positioned over the water filter cartridge during installation. The reason for this is that this device functions as a water port, and as a result, all of the water that you use in your home is filtered here before it is distributed via your home’s plumbing.

Step 6: Screw Casing to Cap

By physically inserting the filter cartridge into the case, you may swap out the filter cartridge. Ascertain that the filter is positioned in the center of the standpipe. Although you may not be able to see it, the standpipe is beginning to slip into the cartridge aperture with relative ease. It is important not to overtighten the casing, since this might cause it to break.

Step 7: Turn Water Supply Back On and Test Pressure

The water supply can be restored by gently turning the intake valve to the “on” position. However, proceed with caution since the water may squirt out with force, destroying the housing and even destroying the entire device. Turning the inlet handle very gently and stopping the inlet valve if the water rushes too rapidly are the proper ways to go about it correctly. When replacing a whole-house filter, exercise caution at all times. Pushing the red knob will allow you to check the pressure. Water will be sprayed out, so be prepared to get a bit wet.

Important Tips Regarding New Filter Replacement

After you have changed the filter and sealed the housing, turn on the water and let it running for 6–7 minutes without using it. Allow it to run for a few minutes to aid in the removal of dirt. The reason for this is because when you replace the filter, it is likely that water sediments will have entered the tap.

How Often Should I Change A Whole House Water Filter?

A typical filter has a lifetime of between 1 and 6 months, depending on the model. Sediment pre-filters have a lower useful life than sediment filters. The post-filters can survive for nine months or more, and the carbon filters are the most durable (lasting 14 to 15 months on average). There are a variety of indicators that your filter is malfunctioning. One of these is an unpleasant odor or taste that you begin to notice in your water as time goes on. Additionally, the flow rate and pressure of the water will alter.

If it is worn out or old, it should be replaced as soon as possible the following time.

However, the factors listed below will also influence how frequently you will need to replace your whole home water filter.

  • Their dimensions, capacities, and types (measured in months or gallons)
  • And The quality of the supply water (a greater concentration of pollutants will shorten the filter’s lifespan and increase the likelihood of a replacement)
  • Sediment, iron content, and other contaminants are all considered. Hardness of the water
  • Using well water vs municipal water

Why You Need To Change Filter

You may make changes to your whole home system whenever you want, which is a huge advantage of having one installed in the first place. Additionally, the technology allows you to modify the water pressure across your entire home in a single step. The purchasing of high-quality water filter cartridges is recommended due to the fact that they last longer and perform more efficiently. Cartridges of good quality can last for up to 36 months, whilst others may only survive for 3 months or less. Changing your water filter on a regular basis is a good idea since it helps to improve the effectiveness of the filter.

If you are unsure how to change a full water filter, see the unit’s owner’s handbook for instructions.

Check to determine whether the cartridge is compatible with the sort of pollutants in your drinking water. A home water screening test can assist you in determining the presence of pollutants in your water.

Wrap Up

Water filters for the entire home are quite simple to replace and have the added benefit of reducing water-borne illness rates in a household. When we drink and wash in clean water, we feel better about ourselves. When replacing your water filter, make sure to put on your safety eyewear. Also, keep in mind that if you notice anything strange about your water source, you should conduct a water screening test. Is there anything you’d want to add to this article on how to change entire house water filters?

How to Change a Whole House Water Filter – Replacement Tutorial

This page may contain affiliate links, so please keep that in mind. If you purchase a product or service after clicking on one of these links, we will get a commission at no additional cost to you. See our product review method in further detail, or read our FTC affiliate disclosure for more information. Almost all whole house water filters require a small amount of maintenance every now and then in order to function at their peak performance levels. In most cases, replacing the cartridges on time solves the problem.

And what happens if you don’t take care of your responsibilities?

Contents

  • This website may contain affiliate links, so please keep this in mind. You will not be charged any additional fees if you purchase a product or service after clicking on one of these links. See our product evaluation method in further detail, or examine our FTC affiliate disclosure for more information. Almost all whole-house water filters require a small amount of maintenance every now and then in order to function properly. In most cases, replacing the cartridges on time will suffice. But how do you go about doing it in practice, and how often do you have to update the filters on your computer? Moreover, what happens if you fail to fulfill your responsibilities. Never fear, we’ll take care of everything. Contents
  • My filter housing has been stuck
  • Please assist me. How frequently should a whole-house water filter be changed
  • How does it affect your health if you don’t update your filter?

Whole House Water Filter Replacement

My filter housing has been stuck; I need assistance. The frequency at which a whole-house water filter should be replaced. When it comes to replacing your filter, what happens is as follows:

ToolsAccessories Needed

  • My filter housing has been stuck
  • I need help. When should a whole-house water filter be changed
  • How does it affect your health if you don’t change your filter?

Step-by-Step Instructions

  1. Whenever possible, the first step is to switch off the water supply. Close the valve at the main water line, or the inlet valve directly before your filter if you have an additional filter installed, to do this. Another possibility is that the machine has a built-in valve that you may use to shut it down. Open as many faucets or other outlets as you can to drain as much of the leftover water as you possibly can. Whenever you notice a considerable decrease in flow rate and pressure, the majority of the water in your plumbing system has exited
  2. If your plumbing system has an output valve, now is the time to close it. As a result, water will not be able to drain back into your home. For a couple of seconds, push and hold the pressure relief button on each filter housing to ensure that you are not dealing with an overpressure situation. With the help of the wrench, remove the (first) housing from its mounting. Keep an empty pail on hand to catch any spilled water if necessary. Remove the old cartridge from within the housing by pulling it out with your fingers. Put it in the empty bucket for the time being, and remember to properly dispose of it after you’re finished with it. Optional: The housings are an example of a component where dirt and germs are prone to build up over time. Consequently, it’s always a good idea to clean the interior of your refrigerator with soapy water or household bleach and a toothbrush. Once you’ve finished, thoroughly cleanse your hands with plain water. Using food-grade silicone oil, lubricate the O-ring on the housing and check to see that it is seated level in its position. If the O-ring is no longer in excellent condition, it should be replaced. Insert a fresh cartridge into the housing and tighten the screw to secure it. It should be sufficient to tighten by hand – an O-ring that has been correctly installed will prevent any leakages. You may now gradually restore water pressure to the system. Open all of the valves in the system that are upstream of it. Look for any leaks. Special care should be paid to any and all of the housings that you have just removed. Should a leak occur, cut off the water supply immediately and gently tighten any connections to halt the dripping
  3. If the leak persists, call a plumber. You may now turn on the water supply permanently, as well as all of the valves heading away from the unit. Open numerous faucets to allow the new cartridge to be flushed for a couple of minutes after installation (see manufacturer instructions). This will also aid in the removal of any trapped air from your plumbing system. Once the water pressure and flow rate have returned to normal, you may turn off all of the faucets and call it a day.
See also:  How To Ground A Gas Hot Water Heater?

Video

Didn’t bother to read because you were too lazy? Take a look at this video:

What If I’m on a Well?

This isn’t really significant. The process of changing a well water filter is identical to that of replacing one on a municipal water source.

Help, My Filter Housing Is Stuck!

If your filter housing is stuck and you’ve already opened one or more faucets to relieve some of the pressure inside of it, as well as utilizing the pressure release button on the top, don’t give up hope just yet! There is still hope! There are a handful of things that may be of assistance:

  • If your filter housing is stuck and you’ve already opened one or more faucets to relieve some of the pressure inside of it, as well as utilized the pressure release button at the top, don’t give up hope just yet! There is still hope! The following are some suggestions that may be of assistance:

Didn’t seem to be working? Once the unit has been gently removed from the water line, it is recommended that it be placed in a vice. You can now push the housing open with your physical might. In the event that you are tired with your current filter, read our whole home water filter reviews to choose a replacement. What can you do to ensure that this doesn’t happen again? First and foremost, check to see that the O-ring is in good condition and free of dirt. If you detect any cracks or other problems in the O-ring, you should replace it.

Additionally, make certain that the seat and contact surface within the head are free of debris.

How Often to Change a Whole House Water Filter

The frequency with which you should update the filter(s) in your whole home system is determined by a number of factors:

  • Their size and capacity (measured in gallons and/or months)
  • Their kind
  • And their capacity Feed water quality (more contaminants will shorten the filter’s lifespan and, as a result, increase the frequency of replacement)
  • Well water vs. city water
  • Sediment and iron levels
  • Water hardness
  • Other contaminants

Generally speaking, most filters will last somewhere between 1 and 6 months in most cases. Pre-filters made of sediment must be changed on a regular basis, but carbon filters have a longer life expectancy than sediment. Post-filters have a shelf life of nine to twelve months. Discoloration and an unpleasant taste or odor, as well as a decrease in water pressure and flow rate, are all indications that your filter has surpassed its capacity and is blocked, and should be addressed as soon as possible.

At the time of replacement, what condition does it appear to be in?

If it’s very unclean and worn out, change it sooner the next time. In addition, we recommend that you examine your handbook or directly contact the manufacturer. Customer service will be able to provide you with a more exact time range.

What Happens If You Don’t Replace Your Filter?

What happens if you don’t replace your filter on time as you had intended? It will lose its ability to filter out harmful substances. For example, an outdated sediment filter that is designed to collect particles such as rust may enable some of the pollutants to flow through, resulting in contaminants ending up in your drinking glass and compromising the function of your other household appliances, among other things. The worst-case situation is that the lifespan of your water heater, washing machine, dishwasher, and other appliances will be significantly reduced.

  • This is something that you must avoid at all costs if you want to keep your health.
  • Thank you!
  • She is the head of content production and has completely immersed herself in the home water treatment sector, resulting in her becoming an expert in the field herself.
  • Find out more about.

How to Replace a Whole House Water Filter Cartridge

Using the entire house water filter housing now in place, you may address your water quality concern with the filter cartridge that you determined would be most effective. When picking the filter cartridge size, keep in mind to take into consideration the ideal flow rate. This blog will offer you with crucial information you should know before beginning, as well as a step-by-step guide for installing a Point of UsePoint of Entry Water Filter Cartridge in your home or business.

Important Tips

WATER SHOULD ALWAYS BE TESTED. Use with water that is microbiologically dangerous or of unknown quality only if suitable disinfection has been performed before and after the unit before use. FILTER CARTRIDGE FLOW RATES are calculated based on the performance of a “clean” cartridge. A filter cartridge / housing with a Gallons Per Minute rating that is two times the needed flow rate should be selected for the job. This enables the cartridge to perform its function for a longer amount of time before the flow rate or pressure deteriorates to an unacceptably high level.

A FILTER CARTRIDGE should be replaced at least once every six months to prevent germs from building up over time.

Instructions

Point of Entry (POE) is a location AFTER the water meter (municipal water) or the pressure tank (private water / water well) and Point of Use (POU) is a location PRIOR to the faucet or appliance in this installation.

  1. Shut down both the intake and outlet valves to relieve pressure in the system. Fill a bucket with water and place it directly beneath the filter housing. Remove the bowl by carefully unscrewing it in a counter-clockwise direction (to the left) using a filter wrench. Remove the used cartridge and throw it away. Pour the contents of the filter bowl into a bucket. Remove the O-rings and clean them well of any lubrication. Check for damage and place the item aside. If the O-ring is damaged, it should be discarded and replaced. Fill the bowl three-quarters of the way with water and add 1 tablespoon (30 mL) bleach. To eliminate any accumulation of bacterial, rust, and scale particles, scrub well with a non-abrasive sponge or cloth before rinsing completely with water. Check to see that the O-ring grooved sitting region is free of debris. Remove the cartridge from its protective box and set it in a bowl, making sure it fits over the post. Apply petroleum jelly to a fresh or cleaned O-ring before inserting it into the O-ring groove. (Optional) Examine to see that the O-ring is seated level and evenly in the groove. Set up the bowl in a clockwise direction (towards the right), twisting carefully until the cartridge is aligned with the post in the filter head – or until it is hand tight. DO NOT TIGHTEN TOO MUCH
  2. In order to prevent flooding, depress and hold the red pressure relief button while gradually opening the INLETvalve as water fills the housing until it runs out of the relief button. Open the OUTLETvalve carefully to remove any trapped air from the line. Before using the system, flush it for several minutes. Look for any leaks.

Just keep in mind that the life of a filter cartridge varies depending on the amount of time it is used and the quality of the water. It is possible that the filter cartridge needs to be replaced if there are changes in the flavor, color, or flow of the water being filtered. More information may be found in our ‘Choosing the Appropriate Water Filtration Solution’ article. If you are not confident in your ability to replace this, you should get a licensed plumber to do it for you instead. If this device is not placed correctly, it may result in water problems down the road.

How to Change a Whole-House Water Filter: A Step-By-Step Guide

A whole-house water filter is an excellent approach to enhance the overall quality of your water. Apart from improving the flavor of your water, a filter system also eliminates potentially hazardous bacteria, pollutants, and other disease-causing pathogens from the water in your house. A whole-house water filter, like most other equipment, requires regular maintenance to keep it from becoming clogged. Changing the cartridge of your water filter on a regular basis is a simple approach to guarantee that it operates at peak performance.

We’ll discuss that and how to do it without calling a plumber in this post.

Why Change Your Whole-House Filter?

It is possible to enhance the overall quality of water by installing a whole-house filter. Apart from improving the flavor of your water, a filter system also eliminates potentially hazardous bacteria, pollutants, and other disease-causing pathogens from the water in your house. In order to prevent a whole-house water filter from becoming clogged, like with other equipment, it must be maintained regularly. Replace the cartridge in your water filter on a regular basis to ensure that it operates at peak performance.

We’ll discuss that and how to do it without calling a professional plumber in this article.

Tools and Supplies List

Prepare all of the tools and accessories that will be needed ahead of time to save time. If you are adequately prepared, replacing a whole-house water filter may be completed in a matter of minutes. Here’s what you’ll require.

  • Make certain that the new cartridge you choose is compatible with your whole-house water filter. There are many different types of filtration systems, so choose the cartridge that is specifically designed for your filter. You will need a wrench to remove the device from its mounting bracket
  • This is normally included with the kit and shipped with the filtration system when it is purchased. Remove the filter from the filter housing and place it beneath the filter to avoid spillage. Remember that you will not have access to clean water during the procedure, so prepare by filling two additional buckets in advance. Make soapy water in one of these to clean the interior of your whole-house water filter, which you will need to do later. Aside from that, household bleach is an optional ingredient. It has the ability to eliminate microorganisms that soap cannot
  • Always remember to use gloves and goggles to protect your eyes and face from splashes of water when working with water. It is possible that the water is polluted or contains solid residue that might cause damage.

Step-By-Step Guide to Replace Your Whole-House Water Filter Cartridge

Before you begin, set the empty bucket beneath the water filter to catch any runoff. Then, at the valve or main feed, turn off the main water supply to your house altogether. If you have an exterior valve, make sure you turn that off as well. Then, with caution, turn the red knob to release the pressure and drain any surplus water by turning on the nearest faucet. After that, prepare ready to take action.

  1. Using the wrench, remove the outer casing of your whole-house water filter and remove the O-ring from the filter. Make that the O-ring is in good condition. It depends on whether it is still in good condition or whether it is worn out and needs to be replaced. If the ring is still in good condition, you can clean it with soapy water or bleach. Make sure to oil the O-ring with silicon grease to prevent it from softening or becoming damaged throughout the process. If it appears to be damaged, it should be replaced before being reinserted into its groove. Remove the old filter cartridge and place it in the empty bucket to be disposed of. Then, using a little amount of bleach and soapy water, thoroughly clean the interior of the filter housing, which is particularly susceptible to germs. Following that, carefully rinse with fresh water. Final step: carefully wash the case to prevent harming it, and then set it aside to dry. Discover where your house water filter system’s standpipe is located within the dwelling. This round device with a small rubber mouth, which resembles a pipe, protrudes from the casing of your water filter and is attached to it. It is sometimes referred to as a water port. Incorporate the replacement cartridge into the housing, making certain that it is aligned with the standpipe in the middle. Screw the cartridge casing onto the cap, ensuring sure that it is still in the centre of the standpipe, and then remove the cartridge case. It’s important not to screw it on too tightly, otherwise it may shatter.

In order to reactivate the water supply, return the valve or intake to its original position. A fast rise in water pressure might cause harm to your whole-house water filtration system if you don’t proceed with caution and progressively turn the valves.

Check for leaks thoroughly, and tighten any loose connections as soon as they are discovered. To ensure that air and any debris or residue left over from the filter replacement operation are removed from the faucet water before using it, let it running for a few minutes before using it.

How Frequently Should You Replace a Whole-House Water Filter?

The longevity of your whole-house water filter is influenced by a number of things. Depending on the size and kind of the water tank, the quality of the water may shorten its useful life. Depending on how polluted the water is in terms of sediment, metal content, hardness, and other contaminants, it is possible that you will need to replace your whole-house water filter sooner than planned. However, on average, most filters may survive for up to six months at a time; sediment pre-filters, on the other hand, require frequent replacement, but carbon filters can last for much longer periods of time before needing to be changed.

  1. Keep an eye out for physical clues such as hazy or strange-tasting water, which might be signs that your filter is blocked and has reached the end of its useful life.
  2. If it appears to be damaged or worn out, replace it with the next one sooner.
  3. Always test the water before installing a whole-house water filter or replacing a filter cartridge in an existing filter.
  4. Furthermore, always get a filter cartridge that has double the flow rate of the one that is needed.
  5. Additionally, if you are unable to locate a filter wrench, adjustable pliers can be used.
  6. Leaks that occur after an O-ring replacement are almost always caused by the O-ring.
  7. After that, check to see that the ring is securely set within its groove.
See also:  How To Add Water Softener To Water Heater?

A Fairly Simple Process

And are you feeling confident enough to change your whole-house water filter without the assistance of a plumber? If so, read on. Providing you exercise caution and use protective clothes such as gloves, the procedure of repairing your water filter should be rather basic and quick. Replace a whole-house filter cartridge does not take much time or require any sophisticated instruments to do it efficiently and effectively. Ensure that you and your family are clear of water-borne diseases and that you are continually ingesting the purest, most pure drinking water possible.

Furthermore, if cartridges are not replaced appropriately, whole-house water filters might cause other water problems, which may need the replacement of the complete filter system.

How to Replace a Whole-House Water-Filter Sediment Cartridge

So, do you think you’re ready to change your whole-house water filter on your own, without the assistance of a plumber? As long as you are cautious and wear protective clothes such as gloves, the procedure of repairing your water filter problems should be rather simple and quick to complete. Changing the cartridge in a whole-house filter does not take much time or involve any sophisticated tools. Ensure that you and your family are clear of water-borne diseases and that you are always drinking the purest, most pure water possible.

Complete-house water filters, in addition, might cause further water problems if the cartridges are not replaced appropriately, resulting in the need to replace the whole system at some point.

Why Use a Whole House Filtration System?

Oh, CULLIGAN MAN, how I adore you! When a home is powered by a properly treated private well or when your water has a high mineral and debris content, you may expect to find an excess of minerals, sediment, and even iron in your drinking, bathing, and cooking water, which will require filtration. It used to be that many individuals would purchase and install a whole-house filtration system specifically for this reason. When we came across one of these homes, we realized that it had been much too long since the sediment cartridge had been changed, so we decided to take on the job.

Changing a water-sediment cartridge was a rather simple procedure, even for inexperienced people like us; here’s how we went about it.

Water Filter Cartridge Replacement Guide

“O CULLIGAN MAN!” exclaims someone. When a home is powered by a properly treated private well or when your water has a high mineral and debris content, you may expect to find an excess of minerals, sediment, and even iron in your drinking, bathing, and cooking water, all of which must be removed by filtration. The installation of a whole-house filter system was formerly very popular, and many individuals purchased and installed one specifically for the purpose. In one of these homes, we noticed that the sediment cartridge had been in place for much too long, so we decided to take on the job of changing it ourselves.

Even for first-timers like us, changing a water-sediment cartridge was a simple process; here’s how we went about it.

Preview of Project Steps 1–7

  1. Turn off the water mains and faucets. To relieve pressure, push the red pressure-relief button. Remove the handle from the ON or BYPASS position and unscrew the casing. Remove the huge O-ring and set it aside after wiping it clean. Remove the used filter cartridge and throw it away. Dish soap and warm water should be used to clean the housing. Completely rinse the dish. Fill the remaining third with water. To disinfect, add approximately 1 tablespoon of bleach and clean well. Thoroughly rinse the dish
  2. Clean silicone grease should be applied to the O-ring before it is reinserted into the groove. It is critical to ensure that the O-ring is seated level in the groove before proceeding. If this is not the case, the housing may not be properly sealed. Reinstall the replacement filter cartridge over the standpipe located at the bottom of the housing
  3. Screw the housing onto the cap and hand-tighten the screw threads. DO NOT TIGHTEN TOO MUCH. Check to see that the cap standpipe fits into the cartridge
  4. Then turn on the water supply. When using a valve-in-head device, slowly turn the handle to the ON position. To relieve the pressure, push the pressure-release button (if present). Before leaving the installation, make sure there are no leaks.

Important Information Regarding Your New Filter Change

The water supply should be turned off. By pressing on the red pressure-relief button, you can relieve some of the pressure. Remove housing by rotating the handle to the OFF or BYPASS position. Remove the huge O-ring and set it aside after wiping it down. Useful filter cartridges should be removed and thrown away. Dish soap and warm water are used to clean the housing. Completely rinse the dish. Approximately one-third of the way filled with water To disinfect, add approximately 1 tablespoon of bleach and scrape.

Apply clean silicone grease to the O-ring and reinstall it in the groove.

A failure to do so may result in the housing failing to seal properly; Reinstall the replacement filter cartridge over the standpipe located at the bottom of the housing; screw the housing into the cap and hand-tighten the screwdriver.

Check that the cap standpipe fits into the cartridge before turning on the water.

Units that have a valve in the head must be turned on carefully. The pressure-release button should be depressed (if present). Before leaving the installation, check for leaks.

Step 1: Water Supply Off and Pressure Release

Turn off the water supply at the valve-in-head or the main water feed to the filter, whichever is more convenient. Release any built-up pressure by pressing the red button. Caution should be exercised since a torrent of water will shoot out when the release button is activated. WARNING: The red button may be used as an excellent prank on someone who is not aware of the water jet that comes out of the housing pressure-relief valve when it is pressed. Just make sure that everyone is wearing safety eyewear!

Step 2: Remove Housing and Clean O-Ring

Remove the huge O-ring from the housing unit by unscrewing it. The O-ring is located within the housing and seems to be a big diameter, but thin, black rubber band in appearance. Remove the lens from the housing and wash it down with a soft cloth before setting the lens aside until you’re ready to reinstall it. Check to see if it is still in excellent condition; if not, place an order for a new one. K9keystrokes lubricate the O-Ring

Step 3: Dispose of Old Filter and Clean Housing

The big O-ring should be removed once the housing unit is unscrewed. The O-ring is contained within the housing and seems to be a big diameter, but thin, black rubber band in appearance. Remove the lens from the housing and wash it clean with a soft cloth before setting the lens aside until you’re ready to reinstall it. Check to see whether it is still in excellent condition; if not, place an order for a replacement. K9keystrokes: lubricate the O-Ring

Step 4: Lubricate O-Ring

Clean silicone grease should be used to properly lubricate the O-ring, making sure to cover both the interior and exterior surfaces of the o-ring. (It is critical to use a silicone-based grease for this application because silicone will not cause the rubber to swell or soften in the same way as a hydrocarbon-based grease will.) Replace the O-ring into its groove once it has been removed. Exercising extra caution to ensure the o-ring is correctly seated can prevent the seal on the housing from leaking, water pressure from degrading, and your water supply being exposed to germs.

K9keystrokes

Step 5: Install New Water-Filter Cartridge

Now it’s time to replace the filter. When you look into the housing, you will notice a standpipe positioned in the center of the base. It is a molded component in the shape of a circle with a short plastic-looking pipe projecting from the center (See photo5). It is critical that the filter be appropriately installed over this since this is the water access port, and as a result, this is where all of your water will be coming from for filtering before being delivered to your house taps. Make an effort to keep the filter centered on the standpipe.

Step 6: Screw Housing to Cap

Replace the housing with the filter cartridge by hand-screwing it to the cap.

Be sure to get the filter centered over the cap’s standpipe. Despite the fact that you won’t be able to see where the standpipe is, you will be able to feel it glide effortlessly into the cartridge aperture. Take care NOT to tighten the housing too firmly, it might shatter easily.

Step 7: Turn on Water Supply and Test Pressure

Turn the water supply back on by slowly rotating the intake lever. Caution should be exercised since if the water rushes in too rapidly, it might cause the housing to blow off and the unit to be destroyed. As a result, operate the intake valve gently and feel the pressure build up as it enters the housing so you can keep it under control until it fills. We replaced a filter with a valve-in-head device, but the same level of caution should be exercised with any water supply input that is utilized.

Water will rooster-tail out of the device, so be prepared to get sprayed a bit (or place a towel over the unit while conducting this step).

Water Filtration System for the Entire House K9keystrokes

Water-Filter Cartridge-Replacement Project Conclusion

After finishing the filter replacement procedure, we turned on the home water and let it run for a few minutes. When we turned on the faucets for the first time, a loud, strange noise erupted from the pipes. It was somewhat shocking at first, until we comprehended what had happened and what had caused it. Initially, the water seemed to be filthy and spit and sputtered sporadically for a period of time. Even simple tasks such as flushing the toilets and checking the shower provided this type of feeling.

Yet another unanticipated project on this historic property?” Eventually, we found that all of the banging and spitting had been caused by air that had gotten into the pipes during the construction process.

To the best of the author’s knowledge, the information in this article is accurate and complete.

India in the year 2011 Arnold On November 30, 2011, India Arnold (author) from Northern, California posted the following: dflood~ Double-check to ensure that the large black rubber gasket has been appropriately inserted and that the pressure valves (inlet and outflow) have been restored to their proper positions.

  • Wishing you the best of luck!
  • What exactly did I do incorrectly?
  • The fact that you feel confident in your ability to change a whole home water filter after following the instructions in this article gives me great pleasure!
  • Cheers On September 5, 2011, K9Chin chin from the Philippines posted the following: We had a water filtration system built beneath our kitchen sink to keep the water clean.
  • I’ve never worked on it before, but with your hub tutorial, I believe I’ll be able to complete the filter cartridge replacement.
  • India Posted on September 03, 2011 by Arnold (author) from Northern, California: PegCole Thank you very much!
  • We found it to be rather simple and even enjoyable!

HubHugs On September 3, 2011, K9Peg Cole of North Dallas, Texas, posted the following: The information is well recorded and illustrated.

I have the impression that I am capable of doing this right now.

Wow, you’re absolutely correct!

See also:  How Much Is It To Replace A Water Pump

Your comments have been really encouraging, and I appreciate you taking the time to read them.

Hopefully, you’ve been enjoying the plumbing contest, since your winning work has been a tremendous gift to the “how-to” community!

The bar has been set quite high!

India The following was posted on September 1, 2011 by Arnold (author) from Northern, California:HRoger Hey, Thank you very much for your thoughtful remarks and votes!

Thank you, K9HRoger, from wherever I am able to be!

on the first of September, 2011: Hello, K9. This is an outstanding HUB! Excellent facts presented in a unique manner! You’ve gotten all of my support: (1)Useful (1)Funny (1)Outstanding (1) (1)It’s beautiful (1)It’s interesting (1) Take care and keep up the good work!

How to Change a Whole House Water Filter

An excellent strategy to preserve your family’s health while also improving the flavor of your water and giving you piece of mind is to install a whole-house water filter. However, once it has been placed, you must continue to clean the filter in order to prevent it from becoming clogged. In today’s article, we’ll show you how to replace the sediment filter or carbon filter in your whole-house water filtration system. Continue reading or find out more by contacting your local West Milford plumbers!

1) Be Prepared

Installing a whole-house water filter is an excellent method to preserve the health of your family, enhance the flavor of your water, and provide you with piece of mind. However, after the filter has been placed, it must be maintained on a regular basis to avoid becoming clogged. Using today’s article, we’ll show you how to replace the sediment filter or carbon filter in your whole-house water system. Continue reading or contact your local West Milford plumbers for more information.

  • The filter cartridge that has to be replaced
  • The wrench that is used to remove the filter housing (which, ideally, was supplied with your installation)
  • The filter housing itself A pail that is completely empty
  • A bucket filled with soapy water (remember, you won’t have water once you cut off the water to clean the filter, so be prepared).

2) Turn Off the Water

Turn off the water mains to the building. Locate the cutoff valve and turn it off to ensure that water does not pass through the filter when it is removed from the system. In addition, you’ll want to drain the pipes of as much water as you possibly can. Remove the water from a faucet someplace in your house and leave it running until the water slows down substantially. Afterwards, shut off the valve that leads out of the filter. Finally, push the release button on the filter housing to release any excess pressure that may have built up inside it.

3) Changing the Filter

A bucket should be placed beneath the filter area to capture the water that will leak out once the housing has been removed. Remove the filter cartridge from the housing by unscrewing it. This should be thrown out. Soapy water should be used to thoroughly clean the inside of the housing. Replace the filter and screw the housing back into place, tightening it a little more than you would have if you had done it by hand. Slowly open the water supply valve to avoid flooding. If you find any leaks, you should shut the valve down once more.

If nothing appears to be amiss, carefully open the valve going away from the filter until it is completely open.

4) How Often to Replace

Changing your water filter cartridge once a year or anytime your water pressure begins to decline is recommended. The presence of low water pressure or water flow suggests that your filter has become blocked. In addition, germs can accumulate in the filter after approximately a year, which is something you should prevent at all costs.

West Milford Water Filtration Specialists

Contact the plumbing professionals at Mark Lindsay and Son PlumbingHeating if you need help with whole-house water filtration or if you want to learn more about how to keep your plumbing system in West Milford running smoothly!

Whole House Water Filter Replacement

Difficulty:Simple Time allotted: ten minutes

SUPPLIES LIST | Whole House Water Filter Replacement

Locate the water main shutdown valve and turn it down to the lowest setting. Find your whole-house water filter, as well as the filter housing wrench, and set them aside. As a precaution, if you are using a well system, you should first turn off the well power before shutting the cutoff valve to prevent the well pump from pumping against a closed system if your main shutoff valve is ahead of the well pressure switch (if you are unsure, simply turn it off). Please remove any upstream water from the system if at all feasible prior to opening the water filter housing.

Our system features a drain located directly below the filter entrance, which makes it simple to drain any remaining upstream water prior to replacing the filter cartridge (see below image with white bowl).

A basement faucet or other low-level faucet can be used instead.

Preparing for the possibility of remaining upstream water by placing a collection basin or something similar under the water filter unit before it is opened is recommended.

  • Loosen Water Filter Housing and Replace The Water Filter
  • Disconnect the water supply, turn off the well pump (if you have one), and empty the system of any near upstream water. Unscrew and open the filter housing and remove the old filter while the system is still running. Cleaning the filter housing should be done prior to changing the filter. Between filter replacements, our filter housing gathers a substantial amount of sand and other debris. I prefer to sterilize the housing after washing it with a weak bleach solution and then rinsing it before putting in the new filter to ensure it is clean.

    Remove it by rubbing it on a moist paper towel and pulling it through.

    When installing the replacement filter cartridge, make a note of the filter’s location inside the filter housing and double-check that it is centered within the filter housing and that any gaskets on the filter cartridge are correctly aligned with the filter housing.

  • Re-assemble the Filter Unit, bleed air and check for leaks
    1. Reassemble the filter housing into the filter unit head following the instructions provided. This may be accomplished by carefully aligning the threads of the filter housing and fitting unit head. Once the threads are engaged, manually tighten the threads until they are snug, then carefully tighten the filter housing wrench an additional 1/4 to 3/4 turn. The o-ring seal should be seated and gently squeezed to ensure proper sealing. Overtightening or tightening an o-ring that has not been lubricated might cause the o-ring to rupture and hinder a watertight seal. Purchase replacement o-rings and swap out the o-rings with each filter change on a regular basis. Remove air from the filter unit by pushing and holding the red bleed button on the top of the filter unit for a short period of time. Finally, switch on the water again and carefully inspect the pipes for leaks. It’s best for me to use a clean paper towel to dry the whole water filter housing before feeling for dampness or indications of water leaks.

    IMAGE GALLERY | Whole House Water Filter Replacement

    Before shutting the supply valves, turn off the electricity to the well pump. To replace the old water filter element, open the basin with the filter housing wrench. After six months of continuous usage, the whole-house water filter element has to be replaced. Drain the water system by opening a valve or a faucet that is located at the bottom of the system. After six months of usage, the water filter element will need to be replaced. In order to better monitor silt, I swapped out the blue filter housing with this “clear” type.

    After the silt and sand have been removed, thoroughly clean the filter basin.

    Prior to re-installation of the filter housing, clean, lubricate, and replace the o-ring.

    Carefully align the threads on the filter housing before reattaching it. Before reattaching the o-ring, lubricate it thoroughly. Do not overtighten the o-ring or you may rip it. To expel air from the system, press the air release valve located at the top of the filter head.

    How to Change a Whole House Water Filter

    Read our instructions on how to change a whole home water filter and you’ll be back to drinking fresh filtered water in no time. One of the most advantageous aspects of a whole-house water filtration system is the ease with which the cartridge may be replaced if necessary. For your convenience, we’ve written this detailed post that explains the reasons why you might wish to update your filter, along with a step-by-step tutorial on how to do so effectively and efficiently. Some of the links on this page are affiliate links, which means that if you click on them and make a purchase, we may receive a commission at no additional cost to yourself.

    What is a Whole House Water Filter?

    In a building, a whole house water filter (also known as a point-of-entry water filter) is a system that filters water coming from every outlet. It is installed at the source of the principal water supply, so that every faucet in your home produces the same filtered water as the others. The alternative to this sort of system is known as a point-of-use filtration system, which is put at individual water outlets to filter the water that comes from that specific faucet and is thus less expensive to install.

    Whole-house water filtration implies that all of the water in the house has been filtered, so you may shower under it, cook with it, and clean with it, and you can access it from any location in the house, including the basement and attic.

    Continue reading if you want to learn how to change a whole house water filter cartridge in an easy, safe, and effective manner.

    Reasons for Changing Your Filter

    Having a whole house system installed has several advantages, one of which is the ease with which you can change the cartridge and regulate the water pressure throughout your entire home in one fell swoop. Investing in high-quality water filter cartridges ensures that your water filtration system will last longer and perform more effectively. High-quality cartridges can last up to three years, while some can last as little as three months. It may be required to replace your filter in order to improve the overall function of your filtration system.

    To determine if it is necessary to change your cartridge or not, see the instruction handbook for the manufacturer’s recommended replacement schedule.

    When selecting a filter cartridge, make sure it is appropriate for the sort of impurities present in your water.

    A home water screening test may be used to determine whether toxins are present in your water. Purchase one from your local homeware store or place an online order. You may also employ a qualified laboratory if you need more thorough testing done. Check out this list for more information.

    How to Change a Whole House Water Filter

    Once you’ve determined that replacing your filter cartridge is the best option for you, it’s time to decide whether you should perform the work yourself or hire a professional to do it for you. Changing your cartridge is not a difficult task; in most cases, the manufacturer has made it simple enough that you can complete it without the assistance of a professional plumber. When it comes to changing the ordinary water filter, you do not need to be a seasoned do-it-yourself homeowner. More information may be found in the instruction manual that came with your filtration system, as there are several distinct types.

    1. Turning off the water supply
    2. Allowing the filtration system to empty
    3. Unscrewing the filter housing with a wrench
    4. Twisting and pushing the filters back in place

    Changing a cartridge is a simple process that can be completed in about 10 minutes by even the most unskilled do-it-yourselfer. Changing a cartridge is a simple process that can be completed in about 10 minutes by even the most unskilled DIYer.

    • Changing a cartridge is a simple process that can be completed in about 10 minutes by even the most unskilled DIY-er.

    Are you interested in learning how to install one of these systems? Don’t forget to check out our beginner’s guide!

    Water Filter Cartridge Replacement Steps

    Are you interested in learning more about how to install one of these systems? Click here. Take a look at our beginner’s guide for further information.

    Conclusion

    A whole home water filter replacement is not difficult, but it may make a significant impact in your quality of life and the health of everyone who lives in your household. Consider taking a water screening test if anything appears to be wrong with your water supply while replacing your cartridges. Follow the manufacturer’s recommended replacement procedures and follow the manufacturer’s advice recommendations. Wishing you the best of luck! More instructions like this may be found on our Facebook page, which is updated on a regular basis!

    Leave a Reply

    Your email address will not be published.