ERNIEGRAVES | Process Measurement & Control

How To Change Water Filter In Whirlpool Bottom Freezer Refrigerator?

Posted on Author Andrey KiligannPosted in CONTROLOTRONLeave a Reply

Your model number may be located in a variety of locations:

Places to look:

  • The internal ceiling of the refrigerator
  • Inside the refrigerator or freezer’s inside walls (perhaps behind drawers)
  • When the door is opened, the frame behind it is visible.
  • In the shadows of the kickplate
  • It’s located on the back of the refrigerator.

A sample model number label looks like this:

Your refrigerator’s water filter works tirelessly to ensure that your drinking water is clean and tastes good at all times.It must be replaced on a regular basis in order to maintain its condition; we recommend changing it once every six months.It’s simple to locate your filter and replace it with a new one after you’ve found it.Continue reading to learn how to locate and change the water filter in your Whirlpool® refrigerator in a jiffy.

Finding and replacing your fridge filter

The first step in replacing your refrigerator water filter is to determine what you already have.Look for the number written on it, or look for the water filter that is certified for use with your Whirlpool® refrigerator.Tips for maintenance: Once you’ve determined what kind of filter you have, consider purchasing a subscription that will automatically mail a replacement filter every three or six months.

Select your water filter

You may replace your Whirlpool® refrigerator water filter by selecting it from the items mentioned below and following the easy replacement instructions, or you can watch a video on how to replace your Whirlpool® refrigerator water filter.

Filter 1: Step-by-step instructions

  1. Look inside your refrigerator for the water filter cover, which should be in the top right-hand corner or in the base grille.
  2. Open the filter door by lifting it up.
  3. Remove the filter and toss it in the trash
  5. Remove the protective covers from the O-rings on your new filter and set them aside. It is important to check that all of the O-rings are still in place once the lid has been removed.
  6. When placing the new filter into the slot, ensure sure the arrow on the filter is facing in the direction of the slot. Do not pressurize the water filter in any way. In case it is difficult to slip into the grooves, twist it until the notches are properly aligned with the grooves.
  7. Close the filter door by pressing it down until it clicks into place.
  8. Once your filter has been changed, pour four gallons of water down the line to ensure that the new filter is fully flushed.

Filter 2: Step-by-step instructions

  1. Look inside your refrigerator for the water filter cover, which is usually in the top right-hand corner or in the base grille.
  2. Raise the filter door a little bit more.
  3. The filter should be discarded after being pulled out.
  4. Remove the protective covers off the O-rings on your new filter and open it up. Replace the filter. After removing the lid, check to see that the O-rings are still in place.
  5. If the arrow on the new filter is facing upward when it is inserted into the slot, it is correct. Keep the water filter from being overworked. In case it is difficult to slip into the grooves, twist it until the notches are suitably aligned with the grooves
  7. Close the filter door by pushing it all the way shut.
  8. Run four gallons of water through your line once your filter has been replaced to ensure that the new filter is adequately hydrated.

Filter 3: Step-by-step instructions

  1. Look for a little plastic cap that fits over your water filter on the left side of the refrigerator’s base grille.
  2. To release the filter, use the eject button on your keyboard.
  3. Remove the filter and toss it in the trash
  5. Remove the protective covers from the O-rings on your new filter and set them aside. After the lid has been removed, check to see that the O-rings are still in place.
  6. Place the filter cap on the replacement cartridge in such a way that the ridges are in alignment. To secure the cap in place, turn it counterclockwise.
  7. Check to be that the arrow on the new filter is pointing to the left before placing it into the slot.
  8. Push the filter all the way in until the eject button pops back out of the filter
  10. Once your filter has been changed, pour four gallons of water down the line to ensure that the new filter is fully flushed.

Filter 4: Step-by-step instructions

  1. Water filter cover may be found on your refrigerator inside in the top right-hand corner of the compartment
  3. If the filter tab on your refrigerator is pointing outward, press down on it and the lid will come off automatically. Alternatively, if you have a tab on the bottom of the cover, you may pull forward and down on the little lever to open it.
  4. Pull the filter to the left as you turn it. Remove the old filter and throw it away.
  5. If this is your first time installing the filter, you’ll find a cap within the filter slot to help you out. Turn it counterclockwise and pull it out
  6. it should come out easily.
  7. For proper placement of the new filter in the slot, align it with the grooves, push it in, and rotate it to the right.
  8. To secure the filter in place, press up on it.
  9. Activate the filter door by pushing it up until it clicks shut
  11. Once your filter has been changed, pour four gallons of water down the line to ensure that the new filter is fully flushed.

Need your model number?

Depending on the model, Whirlpool® refrigerators will show the model number in a variety of locations. Consult our guide to discover where to find yours.

More cleaning tips and tricks

home heartbeat

Are you ready to learn more about home hacks, appliance advice, and more?

Was this article helpful? Pass it on

This item has been added to the comparison list, which can be found at the bottom of this page.

French Door & Bottom Freezer Models

10 steps how to change water filter in whirlpool french door refrigerator

1. Locate the filter

The water filter may be found on the right end top corner of the refrigerator’s interior on the right end.It is possible for filter covers to be released using either a push or a pull release mechanism.The Push style may be distinguished by the use of the term ″Push,″ as well as the fact that both the tab and cover end are facing out.The Pull style will have a tab on the front underside of the cover, and the Push style will not.

2. Release the filter cover

To release the cover from the tab by pressing in on it, then slide the cover down so that the filter cover hangs open at an angle from behind the camera.For the Pull-style filter cover, release the cover by gently tugging the tab toward the front of the filter cover, allowing the filter cover to hang open at an angle from the rear.It is possible that a blue by pass cover will be present within the filter aperture if it is the new refrigerator filter installation.

3. Remove the bypass cap or the used filter

Using a counterclockwise 1/4 turn, unscrew the blue bypass cap and pull it straight out. Keep the cap in case you need it in the future. The cartridge should be unscrewed and removed by rotating them counterclockwise until they are loosened, and then pulling them straight out.

4. Discard the used cartridge.

6. Get the new filter ready

Remove the new filter from any packaging it may have come in and completely remove the seal off the end of the cartridge.

7. Install the new filter

Align the new filter with the opening in the refrigerator, with the thread towards the rear of the refrigerator, and push it in until it is completely seated.

8. Tight the new filter

Turn the filter clockwise approximately 1/4 turn at a time until the filter comes to a complete stop.

9. Close the filter cover

The filter cover may be closed by gently raising it from beneath and forcing it upward until it is snapped shut.

10. Get the filter ready

Allow the water to pass through the filter multiple times before you use it for anything.

Amazon.com: Customer Questions & Answers

Is it necessary to switch off the water in order to change the filter?the question was posed on August 11, 2013 1-10 of 28 responses are shown.It was only a matter of turning off the main water supply.In any other case, the filter wouldn’t fit correctly and would begin to leak.

8/2021 This was useful to 4 out of 4 people.Do you agree?|Inform authorities about alleged abuse I’m not sure if anyone else has said this in the past 7 years, but I’d like to add it for those who are concerned about moving the refrigerator: you can turn off your water where it enters your house or at the road if you don’t know where the shut off is; it’s important to learn where it is before moving the refrigerator.

There are a variety of reasons why every homeowner should be aware of the position of the valve, including leaking pipes and damaged washing machine hoses, among others.Finally, I was unable to install the replacement filter until I switched off the water supply.This was useful to 4 out of 4 people.Do you agree?

  1. |
  2. Inform authorities about alleged abuse Despite the fact that this is an old post, I chose to respond.
  3. You never know when someone else will be experiencing the same issue.
  • No, there is no need to shut off the water supply.
  • I had the same problem with my Samsung, where I couldn’t turn off the filter.
  • No matter how hard I tried, nothing worked.
  • Someone recommended using pliers with a rubber or plastic tip.
  • I didn’t have precisely what you were looking for, but I did have something…
  • read on for more information Despite the fact that this is an old post, I chose to respond.
  • You never know when someone else will be experiencing the same issue.
  • No, there is no need to shut off the water supply.
  • I had the same problem with my Samsung, where I couldn’t turn off the filter.
  • No matter how hard I tried, nothing worked.
  1. Someone recommended using pliers with a rubber or plastic tip.
  2. I didn’t have exactly what you were looking for, but I did have something comparable in my jewelry-making tools box.
  3. a pair of pliers with a large mouth and grippers made of plastic Although they were hesitant at first, they eventually managed to crank the wheel.
  4. It is recommended that you turn the screw 1/4 turn, however if the first turn does not work, you can spin the screw another 1/4 turn.
  5. So locate anything with which you can grab the knob, and with a little effort, you will be able to turn it.
  6. view fewer images Despite the fact that this is an old post, I chose to respond.

You never know when someone else will be experiencing the same issue.No, there is no need to shut off the water supply.I had the same problem with my Samsung, where I couldn’t turn off the filter.No matter how hard I tried, nothing worked.Someone recommended using pliers with a rubber or plastic tip.

I didn’t have exactly what you were looking for, but I did have something comparable in my jewelry-making tools box.a pair of pliers with a large mouth and grippers made of plastic Although they were hesitant at first, they eventually managed to crank the wheel.It is recommended that you turn the screw 1/4 turn, however if the first turn does not work, you can spin the screw another 1/4 turn.So locate anything with which you can grab the knob, and with a little effort, you will be able to turn it.This was useful to 9 out of 10 people.

  • Do you agree?
  • |
  • Inform authorities about alleged abuse Because I rotated the water filter left to loosen it, the endcap on the fridge fell off while still screwed in, spraying water all over the kitchen floor.
  • I had to mop up nearly an inch of water on the floor.
  • It was the manufacturer’s original water filter, which had been fitted.
  • This is the second significant problem I’ve encountered with my refrigerator, which has only been in service for a year.
  • My recommendation is to turn off the water!
  • This was useful to 4 out of 4 people.
  • Do you agree?

|Inform authorities about alleged abuse It’s likely that you should.I’ve owned two Samsung side-by-side refrigerators, and I’ve used them in both configurations.

  1. The first time, I just ripped it out of the socket.
  2. Due to the fact that you are pushing and locking in the new one against the water, it was quite difficult to push and lock it in place at the time.
  3. The second time, I really caused damage to the filter unit within the refrigerator…
  4. read on for more information It’s likely that you should.
  5. I’ve owned two Samsung side-by-side refrigerators, and I’ve used them in both configurations.
  • The first time, I just ripped it out of the socket.
  • Due to the fact that you are pushing and locking in the new one against the water, it was quite difficult to push and lock it in place at the time.
  • The second time, I actually destroyed the filter unit inside the refrigerator because it wouldn’t lock into place.
  • I was frustrated.
  • Until a technician could arrive and fix it, I was without running water or ice until they arrived.
  • I went ahead and removed the fridge out of the cabinet and switched off the water.
  • It was my first time replacing it.
  • It was SO MUCH EASIER, and there was no leakage of water.
  1. In addition, I was able to clean out all of the debris that had gathered under the refrigerator.
  2. It’s a hassle to take it out and turn off the water, but that’s the only way I’m going to do it from now forth.
  3. I really like the idea of shifting the water line to the interior of a cabinet – that’s brilliant!

view fewer images It’s likely that you should.I’ve owned two Samsung side-by-side refrigerators, and I’ve used them in both configurations.The first time, I just ripped it out of the socket.

  • Due to the fact that you are pushing and locking in the new one against the water, it was quite difficult to push and lock it in place at the time.
  • The second time, I actually destroyed the filter unit inside the refrigerator because it wouldn’t lock into place.
  • I was frustrated.
  • Until a technician could arrive and fix it, I was without running water or ice until they arrived.
  • I went ahead and removed the fridge out of the cabinet and switched off the water.
  • It was my first time replacing it.

It was SO MUCH EASIER, and there was no leakage of water.In addition, I was able to clean out all of the debris that had gathered under the refrigerator.It’s a hassle to take it out and turn off the water, but that’s the only way I’m going to do it from now forth.I really like the idea of shifting the water line to the interior of a cabinet – that’s brilliant!This was useful to 7 out of 7 people.

Do you agree?|Inform authorities about alleged abuse When the water filter is at the bottom or its side and not in the top pointing down, you should switch off the water.The pressure, as well as the fact that the filter is on its side in a Samsung, will prevent you from pulling it out without using force.

Once the water pressure is turned off, the pressure will be released effortlessly.Just make sure you obtain the suitable filter for your refrigerator, or else the water system will be harmed.This was useful to 1 out of 2 people.Do you agree?|

Inform authorities about alleged abuse I did not do so.I shut off the ice-making machines (i have 2).Then you may turn off your alarm.Wait a few moments for the water pressure to subside.The filter should be able to be removed immediately.

  • This was helpful to 1 out of 1 people.
  • Do you agree?
  • |

Inform authorities about alleged abuse I attempted to replace the part without shutting off the water.1) It was more difficult to take off the filter.Secondly, a significant volume of water escaped into my refrigerator (but not all over the floor like some others reported).I’m going to turn off the water.When I had my kitchen redone recently, I requested that the water shut-off be placed to the side, within a cabinet, so that I could reach it without having to remove the refrigerator.This was helpful to 1 out of 1 people.

Do you?|Do you want to report abuse?

See also:  When To Change Filter On Zero Water?

I did not.I turned off the ice producers on both sides of the refrigerator.After that, change the water type to ice.The filter came out with relative ease.Previously, the water filter would not budge unless the settings were changed.

  • This was useful to 2 out of 2 people.
  • Do you agree?
  • |
  • Inform authorities about alleged abuse No.
  • It’s as simple as rotating and pulling out the old filter, then inserting and rotating the new filter.
  • There is no need to turn off the water because a water valve is located at the filter connection.
  • This was useful to 6 out of 8 people.
  • Do you believe it?

|Report Abuse

Will a Refrigerator Work Without a Water Filter?

With modern refrigerators, it is simple to have clean, fresh water readily available at all times. The majority of refrigerators today come equipped with built-in water dispensers and ice makers, which means they also come equipped with a water filter. If you don’t require the filter, what do you do? Will your refrigerator function properly if it does not have a water filter?

Can a Refrigerator Work Without a Water Filter?

In rare cases, a refrigerator can function well without the need of a water filter. Specifically, we’ll discuss the significance of refrigerator water filters and when it’s good to forego using one:

How a Refrigerator Works Without a Water Filter

In most cases, a water filter is already included in the purchase price of the refrigerator.It removes pollutants from the household water supply before it reaches your glass of water.Is it possible for your refrigerator to function without a water filter?Water that is not filtered bypasses the filtering process and travels directly to the ice maker or water dispenser when the filter is not fitted.

Some refrigerator models require an additional component, known as a bypass plug, in order for the water to bypass the filtering stage.Some refrigerators, on the other hand, do not require this component.We do not advocate skipping the water filter because doing so can result in bad-tasting water and ice, as well as probable system failure.

What is a Refrigerator Bypass Plug?

Is it possible to use a refrigerator without a water filter?Yes, provided that the bypass plug is properly fitted.Water filter housings are replaced by the plug, which serves to change the water filter.This basically prevents water from entering where the filter is supposed to be located.

If the water filter or bypass plug is not inserted, the water system will not operate properly.Some refrigerators, on the other hand, do not require a bypass plug.They still have water filters in place, but the bypass system operates in a slightly different way than before.The filters on these models are equipped with a cover, which should be used in place of the actual filter.

Why Should I Change My Refrigerator Water Filter?

  • In general, even if you don’t have a home filtration system, you should still use the water filter rather than the bypass plug to prevent water contamination.
  • The filter is there to safeguard both your health and the health of your refrigerator.
  • However, keep in mind that refrigerator water filters must be replaced on a regular basis.
  • If you keep the filter in for an extended period of time, you may begin to notice concerns such as unpleasant tasting ice.
  • Occasionally, the filter will become so clogged that the ice maker will cease to function entirely.
  • If you’re wondering how often you should replace the water filter in your refrigerator, the answer is that it depends.
  1. The majority of manufacturers recommend that you change your filter every six months.
  2. The frequency rises as a result of heavy use of the ice maker and water dispenser.
  3. Don’t be concerned if you don’t know how to change the water filter in your refrigerator.
  4. The location and method of installation vary depending on the make and model of your vehicle, but the fundamentals are the same (follow these instructions to install the bypass plug as well).
  1. The water filter housing should be located according to the user handbook.
  2. Remove the filter by twisting it a quarter turn counterclockwise (some models feature a button to release the filter
  3. see illustration).
  4. Install the new filter by turning it a quarter turn counterclockwise (or pressing it into place with button release models)

Note: If you want assistance with the installation of the filter, one of our refrigerator repair professionals would be delighted to assist you! If you are still unsure about whether or not your refrigerator will function properly without a water filter, give Dave Smith Appliance a call today and we will gladly answer any of your questions.

Does the Water Filter Need to be Replaced?

  1. Last updated
  2. Save as PDF

Does your Whirlpool Refrigerator Water Filter need to be Replaced?

  • Replacement of the Whirlpool water filter is advised every 6 months, or whenever the indication light illuminates, or whenever the filter becomes clogged. A blocked or poorly placed water filter can limit the water flow to the ice maker and dispenser, which can result in one or more of the following problems: ice maker and dispenser malfunctions Ice cubes that are thin or hollow
  • ice or water that tastes strange
  • poor ice output
  • an ice machine that does not produce any ice
  • The measure fill function is not functioning properly.
  • There is no water being dispensed
  • Water is dispensing slowly, and it has an odd taste.

How to Check the Water Filter

For refrigerators with water dispensers, perform the following checks to see whether there is a problem with the water filter:

  1. Water should be dispensed from the water dispenser, and the volume of water flow should be recorded.
  2. Remove the filter from your computer. In any case, the filter is positioned in the base grille below the refrigerator compartment door or within the refrigerator compartment.
  3. Remove the filter from the water dispenser before dispensing it.
  4. If the water flow considerably rises, it is likely that the filter is blocked or that it was put wrongly. In order to fix the low flow, it will be necessary to replace the blocked filter.
  • If the filter becomes blocked and you are unable to repair it quickly, leave the filter out of the water system so that it operates in bypass mode.
  • Having the filter taken out will not affect the operation of the water system since it will continue to work without it, and the clogged filter will not cause slow water dispensing or poor ice production.
  • A new filter, on the other hand, will be required in order to obtain filtered water.
  • REMINDER: After replacing your water filter, be sure to cleanse the system thoroughly.
  • Dripping water from the water dispenser might be caused by air trapped in the water lines.
  • Flush the water system to get rid of any air that has accumulated in the water pipes.
  1. Every time the filter is changed, or every time the refrigerator is connected to the water supply line for the first time, the system must be flushed to ensure proper operation.
  2. For information about cleansing the water system (Anonymous), please see the link below.″> ParseError: Expected End of File (EOF) (click for details) The following callstack is found at (Refrigeration/Water Filter Information/Product Assistance/Does the Water Filter Need to be Replaced?
  3. ), /content/body/div/pre, line 3, column 89: Does the Water Filter Need to be Replaced?

How to Replace a Whirlpool Refrigerator Water Filter

  • The water filters in your Whirlpool refrigerator should be updated every six months.
  • Water from the refrigerator may begin to taste odd and seem murky if you leave it for any longer than this.
  • Ice will begin to smell, and you may detect black particles in the water if you leave it for any longer.
  • It is also possible that an out-of-date water filter will have an effect on the water flow, causing water to slowly dribble out and smaller blocks of ice to be generated.
  • Replacement of the water filter in your Whirlpool refrigerator is a straightforward procedure that should not necessitate the use of any special tools or skills.
  • You will, however, need to be certain that you get the suitable replacement water filter for your refrigerator’s type in order to avoid disappointment.
  1. Installing the incorrect water filter will almost certainly result in the filter not being able to connect to your refrigerator’s main water line.
  2. Identifying the component number, which should be printed on the old water filter, can assist you in ensuring that you receive the proper new water filter for your system.

Step 1: Locate Your Water Filter

  • The position of the water filter in your Whirlpool refrigerator is determined by the model number of your appliance.
  • The water filter will be situated either in the grille at the base of the refrigerator or within the refrigerator in the top right rear corner, depending on the model.
  • Please refer to your refrigerator’s handbook if you are unable to find where the water filter should be located.

Step 2: Preparation

  • Put down a towel before removing the water filter in case there is a little amount of water leakage.
  • For refrigerators with filters, you may want to remove any food or beverages that may be in the way before cleaning it out.
  • Replace the water filter when the ice maker is off in your refrigerator.
  • If the ice maker produces ice while you are replacing the water filter, water may run out of your refrigerator.
  • It may be necessary to switch off the water supply to the refrigerator before replacing the filter on some older models in order to minimize water spillage during the process.
  • However, for the vast majority of refrigerators, this step should not be necessary, since the water supply will be switched off immediately when the filter is removed from the refrigerator.
  1. When it comes to changing the water filter, it should not be necessary to have access to any electrical components, and therefore it should be safe to do so without disconnecting the power.

Step 3: Remove the Water Filter

  • It should be possible to remove the old water filter if the water filter is positioned in the grille of your refrigerator.
  • To do so, you should be able to push firmly on the button located to the left of the water filter, which should cause the old filter to be released.
  • If your refrigerator does not have a button to press, twisting the filter counterclockwise by a quarter turn should be sufficient to remove it from the refrigerator.
  • According to the model, you may also need to press in on the filter while spinning it in order to remove the old filter.
  • If the water filter is housed within the refrigerator, it is likely to be protected by a cover of some sort.
  • There are three options for getting access to the water filter cover: releasing the tab to draw the water filter cover down, lifting the water filter cover, or pressing down on it with your finger.
  1. Once you have gained access to the filter, inserting it into the refrigerator and/or twisting the old filter counterclockwise should be sufficient to remove it.
  2. You should be able to easily remove the old water filter from the refrigerator when it has been freed.
  3. Try pushing more firmly on the release button, since sometimes the button can become stuck, and/or using more pressure while turning the water filter if you are having difficulties removing it.

Step 4: Install the New Filter

  • Whirlpool refrigerators with water filters positioned in the grille include a color-keyed cap that must be unscrewed from the old filter and fitted into the new filter before the refrigerator can be used again.
  • In the event that you have this sort of filter, be certain that the cap has been moved to the new water filter before proceeding.
  • The job of installing the new water filter should be straightforward.
  • Replace the old filter with the new filter by sliding it into the water filter slot on the back of the filter housing.
  • Depending on the model, you may need to spin the new filter clockwise or simply put it straight in until you hear a click and the filter is securely locked into place before continuing.
  • Make certain that the new filter is installed in the same orientation as the prior filter.
  1. If the water filter has arrows on it, ensure sure they are aligned correctly while you are installing the replacement filter.
  2. Before continuing, double-check that the filter is securely fastened in place and/or that the water filter lid is closed.

Step 5: Flush Out the System

  • Before you drink the water, you must first flush the system with water to clean it out and eliminate any carbon fines as well as any trapped air that may have accumulated.
  • It is recommended by Whirlpool that four gallons of water be sent through the system once the filter has been changed.
  • To save time, fill up a one-gallon jug with water and dump it out four times before using it.
  • After you’ve finished flushing the system, you may sit back and enjoy a refreshing glass of freshly filtered water that you’ve earned.
  • Alternatively, if your refrigerator has a ″change filter″ light, you may reset it by pressing the button on the refrigerator.
  • You should remember to switch on the water supply again now that the new filter has been fitted if you had shut it off before installing the filter.

How to Replace a Whirlpool Refrigerator Water Filter

  • Water filters assist to keep the water from your refrigerator or ice tasting pleasant while also keeping the water clean.
  • Whirlpool suggests replacing them every 6 months to ensure that they continue to perform their functions efficiently.
  • To change a Whirlpool refrigerator water filter, just follow the step-by-step directions in this article, which are provided below.
  • Fortunately, it’s a rather straightforward procedure that doesn’t take long to complete.
  • This guide covers the majority of Whirlpool refrigerator models, including the following: 1-A Y 3EAD19XMWR1 3ECKMF10 3ECKMF8 3ECKMF86 3ECKMF10 ED5DHEXWQ00 ED5FHEXVB00 ED5FHEXVL00 ED5FHEXVQ00 ED5PHAXSB00 ED5PHAXSL00 ED5PHAXSQ00 ED5PHAXSS00 ED5PHAXST00 ED5PHA Your first task, if you don’t already have a new water filter, will be to go out and get the appropriate filter, which you may do in person or by ordering them online from a variety of merchants.
  • You may change your replacement water filter by following these procedures once you have obtained the suitable replacement water filter:
See also:  How Do You Know When A Hot Water Heater Needs To Be Replaced

Step 1 – Locate Your Water Filter

Depending on the type of Whirlpool refrigerator that you have, it will either be positioned in the grille at the bottom of the refrigerator or within the refrigerator in the right-hand rear corner on the interior of the refrigerator. If you’re still not sure, see your user guide.

Step 2 – Get Prepared

  • It is a good idea to lay a towel below the filter in your refrigerator, or on the floor if the filter is positioned outside of the refrigerator, to prevent water from pouring on the floor.
  • In addition, you should take any food or other objects out of the refrigerator so that you may securely access the water filter and remove it.
  • You should switch off the ice maker on your Whirlpool refrigerator while replacing the water filter.
  • There could be an additional step required if your refrigerator does not automatically shut off the water supply when the water filter is removed (most newer Whirlpool refrigerators have this function)
  • you may additionally need to turn off the power to your refrigerator.
  • Because you will not be in contact with any electrical components when changing the water filter, you will not be required to cut off the power while doing so.

Step 3 – Remove the Old Filter

  • If the filter is positioned in the grille, you may remove it by pressing down on the button to the left of the filter, and you should be able to pull the filter out from behind the grille. If your filter does not have a button on it, you may remove it by rotating it counterclockwise, which should release it and allow it to fall out of the way. It is sometimes necessary to press it in while turning it in order to release it.
  • If your Whirlpool refrigerator has a filter within it, you will first need to remove the cover from it, or in certain models, you may just push the filter up into the fridge. Once the cover has been removed, you simply need to push the button on it and pull it out, or if there isn’t a button, you may push the filter and spin it counterclockwise until it becomes loose, at which point you can pull it out
  • The filter can be difficult to remove at times
  • if you’re having difficulties, simply press it in harder
  • this should loosen it up enough to allow it to be removed.
  • I hope you have been successful in removing the old filter by this time.

Step 4 – Install the New Filter

  • Some models will have a cap on the filter that will need to be removed from the old filter and placed onto the new filter
  • this will be the case with some models.
  • To install the new filter, first push it into the opening and then turn it clockwise until it is securely in place
  • if the filter has a button, you can simply click it into place
  • then, depending on your specific model, you may have to push it in and turn it counterclockwise until it is securely in place
  • When installing a new filter, make certain that it is installed in the same location as the previous one.
  • You should double-check that it is securely fastened in order to prevent any water leaks from occurring.
  • You should now have a working water filter that you’ve successfully installed.

Step 5 – Flush Out the Water

  • You must flush out the water in your refrigerator in order to get rid of the old, polluted water that has accumulated. Depending on the manufacturer, you should drain around 4 gallons of water before drinking the water after installing a new filter. Once you have properly drained out the water, you may turn the ice maker and water back on if you had previously turned them off. You may now take pleasure in a refreshing drink of water.
  • Finally, on some Whirlpool refrigerator models, there is a water filter button that illuminates when the water filter needs to be replaced, which is convenient. If your refrigerator has a reset button, you’ll need to push it to get it back to normal.

How to Clean Stainless Steel Refrigerators

  • Article to be downloaded article to be downloaded A stainless steel refrigerator may transform your kitchen into a contemporary haven, but cleaning it can be a difficult task at times.
  • Follow this guidance as you attempt to remove streaks, stains, hand prints, and other blemishes from your stainless steel refrigerator, and you’ll have figured out how to clean a stainless steel refrigerator in no time.
  1. 1 Use a cleaning cloth that is not abrasive. Stainless steel is readily scratched, and even a light kitchen cleaning pad will leave a mark on the metal’s surface. Make use of a microfiber cleaning cloth. Their performance is superior than that of lint-free cotton due to the fact that they leave less fibrous material on the stainless steel surface
  3. Paper towels may be used to clean and polish your refrigerator. Clean the surface using a microfiber cloth and your preferred cleaning product first, and then wipe down the refrigerator with paper towels if you want a super, non-streaky shine.

2Clean in the direction of the grain. Even if you have to look very carefully in order to see the grain, you will be able to tell which direction the grain is moving in. If you rub against the grain of your appliance’s surface, even using a microfiber cloth, you will create permanent scratches on the surface of your appliance. Advertisement

  1. 1Use ordinary water instead of distilled. Although this is the simplest technique of cleaning your refrigerator, persistent stains and fingerprints will need more rubbing or the use of a few drops of dishwashing liquid soap to remove them completely. If you use soap, you will need to rinse the soap off the surface with clear, hot water before drying it with a paper towel to avoid streaking. (Make sure to dry it fast so that it doesn’t leave streaks.) 2Clean with vegetable oil. It is possible to clean stainless steel using any vegetable oil, including olive oil. You may also use baby oil
  2. however, washing with oil necessitates more drying time in order to absorb the oil
  3. yet, this cleaning approach produces a highly glossy finish but a deeper colour.
  4. 3Try cleaning your device with white vinegar and water. Using three parts white vinegar and one part water, combine the two ingredients in a spray bottle and use as directed. Use a spray bottle to clean your refrigerator, then wipe it off with paper towel. 4Use commercial cleansers to remove greasy fingerprints. Vinegar is good at cutting through greasy fingerprints. Others like the ease of glass cleaning solutions and products designed exclusively for cleaning stainless steel appliances, which are available on the market. Advertisement
  • Question Add a new question Question I used Cerma Bryte Brightener to clean my stainless steel refrigerator, assuming it was the polish, and the finish is now streaky as a result. What can I do to help? Weiman stainless steel wipes or spray are recommended. After that, dry the area with a microfiber towel.
  • Concerning the Question In order to properly clean stainless steel equipment, what is the best cloth to use? Make use of a microfiber cloth or anything just as soft. In a pinch, an old t-shirt or pair of panties can suffice.
  • Concerning the Question I used stainless steel cleaner to clean the inside of my stainless steel refrigerator. What should I do to get rid of the smears? I clean my refrigerator with apple cider vinegar, and it is completely immaculate. Spray a clean cloth with vinegar and wipe the fridge off. Then use another clean cloth to wipe it down once more to remove any residue. The end product is spectacular.
  • Concerning the Question What is the best way to remove paint smudges off the textured side of a stainless steel refrigerator’s door? Try rubbing alcohol as a last resort. Remove the stains by soaking a sponge or cotton ball in rubbing alcohol and wiping them away. To remove stubborn stains from the texture, soak an old toothbrush in rubbing alcohol and gently scrape away at the spot in circular motions.
  • Question Something has left a streak on the inside of my stainless steel refrigerator. Stainless-steel cleaners do not work on stainless steel. What do you think is the best course of action? Mineral oil is a good option (baby oil is mineral oil with perfume). Make use of 0000 steel wool in an unobtrusive location. Quad Zero steel wool is what you’re looking for. Anything less than this will result in harm to the finish. Make use of 0000 steel wool, mineral oil, and elbow grease to get the job done. Go gently against the grain of the finished surface. Never wipe, brush, scrape, or otherwise manipulate the finish against its grain.
  • Concerning the Question What is the best way to remove the markings made by a nylon scrubber? In the event that you scraped your fridge with the scrubber, there may be nothing you can do about it. If the discoloration is only on the surface of the refrigerator, try cleaning it using solutions designed exclusively for stainless steel refrigerators – there are numerous different types of sprays and cleaning wipes available. Instead, only use soft cloths with stainless steel cleanser or other cleaning solutions that are safe to use on stainless steel in the future. What is the best way to repair scratches on my refrigerator caused by a brillo pad? Consider using carnauba wax. Because the wax is flammable, use it with caution and dispose of any excess immediately rather than allowing it to accumulate.
  • What is the best way to clean the LCD screen on the refrigerator door? The baking soda and water solution was applied using a micro-fiber cloth, and the surface was subsequently cleaned with paper towels. You don’t require a large amount of the soda.
  • Question What is the best way to remove adhesive labels off my stainless steel refrigerator? Soak the stickers with WD-40 and let them sit for a minute before attempting to remove them. Something simple like Goof Off should suffice.
  • Question How can I remove lemon juice stains from the inside of a stainless steel refrigerator door? Try using baby oil or vegetable oil, and then rinse well once you’ve gotten it off. Oil is typically effective in removing stickers from any surface, and it is safe to use on stainless steel appliances such as refrigerators.

Inquire about something There are 200 characters remaining. Include your email address so that you may be notified when this question has been resolved. Advertisement submissions are welcome.

Video

  • Although club soda is effective on stainless steel, many people are reluctant to use it due to the fact that it is dirty.
  • A non-oily product will produce the finest sheen, but the refrigerator’s surface will gather dust and grime more quickly than if you use a vegetable oil, baby oil, or any commercial cleaning that contains oil.
  • Vinegar may also be used undiluted
  • simply splash some on a microfiber cloth and massage it in with the grain of the fabric. When used at maximum dosage, the stench is significantly stronger, although it disappears quite rapidly.
  • Each and every one of the cleaning solutions described in this article may be used to clean stainless steel pans, utensils, and counter tops.
  • No cleaners are required to clean your stainless steel equipment
  • a $1 microfibre cloth and simple water will suffice.
  • Thank you for submitting a suggestion for consideration! Advertisement Some commercial cleaners have the potential to damage your floors. Before spraying a cleaning on the refrigerator, cover the floor around it with towels or an old mat as a precaution.
  • Gloves should be used to protect your hands from the toxins included in professional cleaners.

Advertisement

Thing’s You’ll Need

  • Microfiber cloths, paper towels, and commercial cleaners (optional) are all good options.

About This Article

  • Summary of the ArticleXTo clean a stainless steel refrigerator, begin by spraying it with a solution of white vinegar and water and wiping it down with paper towels.
  • Then, using clean, hot water, thoroughly rinse the surface before drying it off.
  • When cleaning, be sure to use a microfiber cloth and wipe with the grain of the steel to avoid scratching the surface..
  • Additionally, dry your refrigerator with paper towels to give it a lovely sheen and lustrous appearance.
  • Continue reading for information on how to clean your refrigerator using olive oil or baby oil.
  • Did you find this overview to be helpful?
  1. The writers of this page have together authored a page that has been read 433,440 times.

How to Put Freon in a Refrigerator

  • Article to be downloaded article to be downloaded The process of adding Freon to a refrigerator is difficult.
  • In the event that you add too much Freon, use the incorrect type of Freon, or fail to properly install the bullet-piercing valve, you run the danger of irreparably harming your refrigerator.
  • Freon is also poisonous, and ingesting it can result in a range of health issues.
  • It should be avoided at all costs.
  • If you don’t want to hire a refrigerator repair firm and are confident in your ability to handle a refrigerator, you should do it yourself.
  • To begin, determine why your refrigerator isn’t functioning properly.
  1. Check the vents on the back and interior of your freezer to determine if any frozen coils need to be defrosted, and if so, defrost them.
  2. Replace or repair any leaky pipes to prevent further damage.
  3. Then, before adding the Freon, attach a bullet-piercing valve and check the Freon pressure with a specialist gauge before continuing.
  • 1 First, determine whether or not your refrigerator makes use of Freon in any way.
  • Because freon is harmful to the environment, most refrigerators manufactured after 2010 do not contain it.
  • There are also a significant number of refrigerators manufactured after 2003 that do not contain Freon.
  • In order to determine whether or not your refrigerator includes Freon, open the refrigerator’s doors and search for a metal or plastic label that displays the product’s information.
  • It will provide a description of the cooling technique.
  • There are several distinct forms of Freon available.
  1. It is possible to choose from the following options: R-12,R-13B1,R-22,R-410A,R-502,R-503, and R-503.
  2. Adding Freon to your system is simple; just make sure you use the exact type of Freon that is mentioned on the label.
  • CFC is an abbreviation for chlorofluorocarbon. ‘Freon’ is the scientific name for the substance. If your refrigerator is powered by CFC, it operates on Freon.
  • 2 Make a visual inspection of your ventilation system for obstructions and clean them as needed. High interior temperatures are frequently caused by obstructions in the vents, which are one of the most prevalent reasons. To begin, look for a leak near the back of your refrigerator’s vent. Then, using a flathead screwdriver, pry open the rear panel of the freezer to inspect the inside vent, which should be accessible. They should be cleaned out with a paper towel and debris should be removed if they are filthy. Clean up the water and check to see whether the problem has resolved on its own. If you have a damaged vent fitting, you may obtain a replacement from the manufacturer directly. To discover how to remove a vent, go to the instructions that came with your specific model. In most cases, a flathead screwdriver or a chisel will enough to pry them apart.
  • Promotional material
  • 3 To check if your freezer coils are frozen, remove them from the freezer and thaw them. If your freezer is malfunctioning but your refrigerator is operating normally, it is possible that your freezer coils are frozen. Make sure there are no pieces of ice on the coils that are hidden behind the rear panel of your freezer by checking behind the back panel. if the freezer coils are frozen, disconnect the machine and leave it unplugged for 24-36 hours to allow the coils to thaw Remove the defrost drain pipe from the service panel and soak it in hot water before reinstalling it, as necessary.
  • 4 Spray suspected leaks on freezer pipes with water to check whether it bubbles and if so, look for holes in the pipework.
  • Examine the pipes in your freezer, which are hidden behind the panel, and the pipes below your refrigerator, which are near the compressor tanks.
  • If you notice any water pooling, remove it from the area and wipe the water off of the pipework.
  • Fill a spray bottle halfway with tap water and saturate the pipes with the solution.
  • If the water begins to bubble up in a specific spot, you have discovered a hole.
  • Aluminum pipes can be soldered together to fix gaps, or the pipe can be completely replaced.
  • 5) Check to see whether the problem has been resolved before adding more Freon to the system.
  • If you have a problem with your vents, coils, or water lines, you most likely do not need to add any extra Freon.
  • After you’ve resolved an issue, let your refrigerator a couple of days to see whether it returns to its normal operation.
  • If it does, you won’t have to use any Freon at all.
  • If the problem does not resolve on its own, you will need to have the Freon levels checked.
  • Problems with the Freon in your refrigerator might lead to a variety of additional issues.
  1. It’s probable that the frozen coils, leaking pipes, and blocked vents are signs of a broader problem with your Freon lines that has to be addressed.
    Advertisement
  1. 1 If your evaporator coil needs to be changed, you should do so. Evaporator coils are one of the first components of a refrigerator to incur damage, and this is usually the case. Remove the rear panel of your freezer by wrapping a flathead screwdriver around the sides and pulling it out from the bottom. You’ll see a vast collection of coils that are all joined together in a single unit. Check the coils to check if the evaporator needs to be changed. Look for leaks or corrosion to determine whether the evaporator needs to be replaced. Replacement parts may be ordered from your manufacturer and installed by unscrewing the pipe that links the replacement part to the supply line in the bottom of your refrigerator. Before restarting your refrigerator, screw in the new set of coils into the same port and tighten them down to guarantee proper operation.
  2. It’s possible that your coils are just filthy. If they appear to be unclean, use coil cleaning foam and paper towels to clean them. It is possible that the dirt is preventing evaporation from escaping your freezer and that it is leaking down to the bottom of your refrigerator.
  3. Never use a different brand of evaporator coil in your refrigerator than the one that came with it. They are intended to function only with certain models of vehicles.
  • 2 If you don’t want to replace the entire line, fix faulty pipes near your compressor first before proceeding. If you have access to both sides of the threading on a pipe, you can replace the entire thing. Order a new pipe from the refrigerator’s manufacturer and inquire as to whether any cautious measures are required while replacing a specific pipe in your refrigerator. Unplug your refrigerator and follow the manufacturer’s instructions before unscrewing the pipe and replacing it with the new one you purchased. Some plumber’s tape may be required to cover the threads on your new pipes and keep the fittings tight
  • however, this is not always necessary.
  • Check your water lines if you notice any standing water. Essentially, these are the pipes that travel from the frame of your refrigerator to the supply lines.
  • A wrench or channel locks may be required to release a bolt that holds a pipe connection together
  • however, this is rare.
  • Any pipe that runs into the frame of your refrigerator will require the services of a qualified professional to be replaced.
  • 3 Solder aluminum and copper pipes together to patch up tiny holes and leaks in the system. While it’s nearly always easier to replace a whole item, you may fill up tiny holes and leaks by soldering an aluminum or copper plate over the area that has to be repaired. A tiny aluminum or copper strip, some soldering flux, a clamp, and a soldering tool should all be purchased. Clamp the aluminum plate over the hole and add flux to the joint surrounding the aluminum plate to seal it in place. Use your soldering iron to heat the junction and solder the two pieces together after they have been heated. Allow your pipe to cool for at least 12 hours after it has been heated.
  • You are not permitted to solder any pipes that contain combustible materials. Because freon is a dangerous gas, always double-check with the manufacturer if you aren’t sure which pipe you are soldering.
  1. For those who are not familiar with soldering pipes, it might be difficult to do it without expert assistance. Consult with a fridge repair firm if you’re not sure in your ability to mend pipes on your own.
  2. 4
  3. Prior to introducing Freon, make sure your leak or damaged components have been repaired to avoid further difficulties. Repairing any leaks or broken parts first will ensure that your refrigerator continues to leak, and any more Freon you add will be ineffective. Once you’ve determined the source of the problem with your refrigerator, you should solve it before adding any Freon. Advertisement
  • Step 1: Disconnect the refrigerator’s power cord and remove the screws holding the back panel in place.
  • Pulling your refrigerator out a little bit and unplugging it will save you time.
  • To gain access to the rear panel of the refrigerator, turn it around such that it is always located near its lowest point on the shelf.
  • Remove the bolts and screws by using a wrench or a screwdriver to loosen them.
  • Remove the panel from the wall and set it aside.
  • In order to keep food that will go bad soon or that will melt cool, fill a cooler with ice and store it there to keep it cool.
  • Finding the Freon pipe may be accomplished by checking for the compressor tank. When you open your refrigerator, you will see a big tank located at the bottom of the unit, beneath the control panel. It compresses the heated air and cools it before returning it to the refrigerator for cooling. Your Freon line will connect directly to your tank and feed straight into your refrigerator’s compressor. Refer to your refrigerator’s owner’s handbook to establish which pipe is the Freon line if there are many pipes present. In every refrigerator, the mechanical components are arranged in a distinctive manner. The position of your refrigerator’s Freon lines will be determined by the manufacture and type of your refrigerator.
  • On some refrigerators, the Freon line is connected to the suction line as well. Another option is to use a dedicated pipe
  • the Freon line is nearly generally constructed from copper in these cases.
  • 3 Install a bullet-piercing valve around the Freon line near your compressor to prevent it from leaking. The bullet-piercing valve is comprised of two components. Unlock the three nuts with an Allen wrench and wrap the pipe near the compressor with the wrench in place. It is possible that you may need to alter the size by connecting the two separate sections with an adapter. The bullet-piercing valve will pierce the pipe and force the contents of the pipe through the valve to the drain. This will allow you to gain access to the pipe without having to remove it. Two adaptors are included with the bullet-piercing valve. Make use of the adapter that corresponds to the size of your tube.
  • Purchase a bullet-piercing valve from a hardware shop or a refrigerator repair service.
  • An Allen wrench should be used to tighten the valve.
  • Caution: The valve must be totally tight against the pipe in order to function properly. Your system will leak both air and Freon over time if your connection is not secure. This can pose a serious health risk. If you accidently damage the valve or install it incorrectly, seek the advice of a professional repair technician.
  • 4 Remove the conversion valve from the bullet-piercing valve by unscrewing the cover on the side of the valve. There is a cap on the side of your bullet-piercing valve that allows you to gain access to the pipe without having to open the valve. Remove the cap by hand by twisting it in the opposite direction of the clock until it loosens. It should not be necessary to use any tools in order to remove the cap. Attach the conversion valve to the opening where the cap used to be by screwing it on. The valve is similar in appearance to the air valve on an automobile tire.
  • 5 Connect the gauge to your refrigerator and plug it in to acquire a reading. Reconnect the refrigerator’s power cord to reactivate the compressor. Hold the air compressor gauge on to the adapter for 10-15 seconds before latching it on to acquire a pressure and Freon reading from it. You’ll need to utilize a compressor gauge that’s made exclusively for Freon refrigerators in order to get accurate readings. Purchase or rent one from a refrigerator repair service or a hardware shop. In order to function properly, the compressor gauge must be able to read both pressure and Freon levels. It should be equipped with two gauges, each of which would offer two separate readings.
  • If the Freon level is in the blue portion of the gauge, you have enough of Freon
  • otherwise, you need to refill the tank.
  • 6 Check to see that the pressure gauge does not indicate more than 0 psi. Contrary to popular belief, the pressure in your system should be zero pounds per square inch. This is due to the fact that the Freon line is sucking air into it in order to compress it. As a result, if the refrigerator is functioning properly, there should be little or no pressure in the suction or Freon lines. Check the pressure gauge to determine if the needle is resting at or near zero psi by peering down at it. If the needle is greater than 0 but less than 1 psi, you’re in good shape
  • otherwise, you’re in trouble.
  • If the pressure inside your system is greater than 1 psi, bleed some of the air out by opening the valve without attaching anything to it for a short period of time. Repeat this process for 4-10 seconds and then retest your valve.
  • 7 You can figure out how much Freon to add by referring to the label on the inside of your refrigerator. The amount of Freon required by your refrigerator or freezer will be indicated on the sticker on the interior of the device. You must cross-reference the reading on the gauge with the information on your label because every brand and model is different. If the gauge reads a figure that is lower than the threshold for your refrigerator, you will need to add Freon to the system. Obtain the assistance of a refrigerator repair professional if the Freon reading falls within the range specified on the refrigerator’s label. The problem isn’t with your Freon pipes or supply
  • this is the same label that you examined to see if your refrigerator utilizes Freon in the first place.
  • In rare cases, the label can be seen on the back of the refrigerator.
  • 8 Connect your Freon tank to the recharge hose and then plug the hose into the adapter to complete the installation process. Purchase a new tank that is filled with the exact type of Freon as was used in your original tank. The Freon will be sent with a hose that will allow you to connect it to the adapter on your bullet-piercing valve if necessary. Applying force to each fitting in a clockwise direction until it is tight, screw the Freon into the valve with the hose. The Freon should be released by rotating counterclockwise on the valve located on top of the tank to relieve the pressure. To properly service your refrigerator, you must use the exact type of Freon that is mentioned on the refrigerator’s label. R-12, R-13B1, R-22, R-410A, R-502, and R-503 are among the potential varieties. Some Freon tanks are equipped with gauges, which allow you to see how much Freon you’re releasing at a glance. If your tank doesn’t have one, you’ll have to rely on trial and error to bring the Freon levels in your refrigerator within the proper range.
  • 9 Close the bullet-piercing valve and take the adapter out of the system.
  • Make sure the cap on the top of your Freon tank is tight by turning it clockwise until it’s snug.
  • Next, disconnect the hose from the adaptor and remove the adaptor by unscrewing it.
  • To close the adapter valve, replace the cap with a tight fit.
  • Close the rear of your refrigerator by screwing the back panel back in place.
  • Once the bullet-piercing valve has been fitted, it is not possible to remove it.
  1. Your suction line or Freon supply will be compromised as a result of this action.
    Advertisement
See also:  How Many Gpm Tankless Water Heater Do I Need?

Inquire about something There are 200 characters remaining. Include your email address so that you may be notified when this question has been resolved. Advertisement submissions are welcome. It’s important to remember that if your refrigerator has freon, you’ll need to contact a professional to remove it when you’re ready to dispose of your refrigerator.

Advertisement

Things You’ll Need

  • The following items are required: soldering tool, flux, torch or soldering equipment.
  • Bullet-piercing valve (with Allen wrench)
  • Freon tank (with wire brush)
  • Clamp (with aluminum plate)
  • Wire brush
  • A converter for air conditioning conversion
  • Freon recharge hose, Freon gauge, and multi-bit screwdriver are all included.

About This Article

Thank you to all writers for contributing to this page, which has been read 82,168 times so far.

Leave a Reply

Your email address will not be published.