How To Build A Water Heater Enclosure Outside

How to Build a Water Heater Shed

It is recommended that you contact a certified plumber if you have a leaky water heater. Shutting off a water heater should only be done at your own risk and should be done with caution. Prepare your home by knowing where the main water supply cut off is located in case of an emergency before you begin. Before it enters the water heater, the cold side is protected by a shut-off valve. Turn it off if it is on. Near the bottom of the heater, there should be a gas supply shutoff valve. Not on the heater itself, but on a gas pipe that leads to it.

The next step would be to turn on the hot water side of a lavatory faucet to relieve some of the pressure.

This reduces the pressure inside the tank, which makes the leak less aggressive and less damaging.

  • The following items are required: spray paint, ruler, shovel, rake, landscaping fabric
  • Gravel
  • Tamp
  • Rebar
  • Hammer
  • 2-by-4 boards
  • Circular saw
  • Safety goggles
  • Nails
  • Expansion strip
  • Concrete
  • Pressure-treated wood
  • And a hammer. Masonry screws, a hammer drill, miter box, 1/2-inch plywood or oriented-strand board, string, tacks, 30-pound roofing felt, a hammer stapler, staples
  • Siding
  • Primer
  • Paint
  • Asphalt shingles
  • Rolled fiberglass insulation
  • Doors
  • Windows

Tip

When cutting the wood, make sure you use safety eyewear.

Building the Foundation

  1. In order to outline the boundary of the shed, spray paint the ground adjacent to the home. In this example, we’ll construct a shed that is 4 feet by 6 feet. This will provide access all the way around the water heater, as well as a little amount of additional storage space. Make the marks a little larger than the perimeter of the shed, so add 3 inches to the front border and each side of the building, for a total of 6 inches. Dig to a depth of 4 inches in the dirt inside the spray-painted lines that have been drawn on the ground. Smooth out the soil at the bottom of the trench with a rake. Place landscaping cloth over the dirt in the hole to protect it from the elements. This helps to maintain the soil and prevents the growth of weeds. Into the hole, pour 2 inches of gravel, then rake the gravel flat and tamp it with your hands
  2. Reinforce the concrete by placing rebar on top of the gravel. Place the rebar in a grid pattern, with the bars one foot away from one another
  3. To protect the hole’s perimeter, pound wooden stakes into the ground every 3 feet around it and fasten two-by-fours to the stakes around the inner border. Place an extension strip adjacent to the foundation of the home. Because of this, the base and slab for the lean-to may expand and compress as necessary. Fill the hole with concrete that has been mixed according to the manufacturer’s instructions. By running a two-by-four across the top of the wooden frame, you may smooth out the concrete’s surface texture. Allowing for a minimum of four to five days for the concrete to dry before removing the wooden form

Building the Shed

  1. The sill plates will be made from four two-by-fours that have been pressure treated. These boards serve as a connection between the wall frame and the concrete slab. Cut the two side boards to a total length of 41 inches, and the front and rear boards to a total length of 72 inches, respectively. Place the rear sill plate on the slab against the side of the house, centered such that there are 3 inches of slab on either side of the sill plate. Repeat this process for the other sill plate. Every 6 inches, using a hammer drill, drive masonry screws through the sill plate and into the slab of the house. Place the side plates on the slab, matching the outside edges with the outer margins of the back plate, and fasten them in place using masonry screws to hold them in place. Install the front plate against the side plates in the same manner as you did the side plates
  2. Untreated timber was used to construct the top and bottom plates for the front wall of the shed. The top plate measures 6 feet in length, while the two below plates are 1 foot in length each. Preparation: Measure and cut four wall studs measuring 81-1/4 inches in length for the front wall, as well as two jack studs measuring 715 1/2 inches in length. The jack studs should be placed on the sides of the door frame to provide the structure additional strength
  3. And Into each end of the bottom plates, nail a wall stud to create a frame that resembles the letter “U.” Placing one of the frames on the ground, lining up one edge of the top plate with one of the outside studs, and driving two nails into each stud through the top plate will complete the installation. Do the same thing on the other side. Cut the two-by-fours that will be used to construct the rear wall frame. Remove the top and bottom plates, which should be each 6 feet long, as well as the four wall studs, which should be 8 feet high. An 18-degree angle miter cut should be made at the top of the wall studs to account for the roof’s sloping. Nail the studs into the bottom plate at an 18-inch-center distance, then nail the top plate to the tops of the studs at an 18-inch distance. When nailing the studs into the bottom plate, use the straight, unmitered edge and make sure that the cuts on the top of the studs all point in the same direction. Nail half-inch plywood or oriented-strand board to the back of the back wall frame with a finishing nail or two. To accommodate the width of the roof rafters, raise the sheathing about 3-1/2 inches above the frame to provide for a 3-1/2-inch overhang. Create a space between the boards such that there is no place where the corners of four boards meet together. Preparing the side walls requires cutting top and bottom plates for the side walls that are 41 inches long, as well as three studs for each side of the shed that are 8 feet long. Make sure that the studs are 16 inches apart when you nail them into the bottom plates. You do not need to nail the top plate to the side walls just yet
  4. Instead, raise each wall frame onto its matching sill plate and nail it to the sill plates every 6 inches in a zigzag manner to hold it in place. When placing the rear wall frame, make sure that the top plate slopes down toward the front wall so that it is flush with the front wall. To make the shed stronger, nail the end studs of each neighboring wall together at the corners. Attach a thread to the outer border of the top plate of the rear wall frame. (See illustration.) To finish the front wall, run the string all the way down to the back corner of the top plate and attach it tautly to the top plate. Draw a trace of the string line onto the studs on the sides of the building. This diagram illustrates where you should cut the studs so that the roof may slope down to the front of the shed and out the sides. This process should be repeated on the other side wall. Make use of nails to attach the jacks to the end studs that form the door frame. Remove the bark from two 2-by-4 boards that are 4 feet in length, then stack them on top of each other and nail them together. The header for the door frame is seen here. Place it on top of the jack studs, then nail the header boards into the end studs along the door frame to secure it in place. Make a template board for the roof rafters to use as a guide. Cut a two-by-four board that is 51 inches long, and then create a 72-degree miter cut on one edge of the board to complete the project. Placing the board on the outside of one of the side walls such that the mitered edge is aligned with the sheathing that rises over the rear wall is the best way to start. Using a pencil, sketch the edge of the front wall onto the rafter, and then cut the board following the lines you made. Using the template as a reference, cut five rafters for the roof structure. The rafters should be attached to the tops of the walls by putting a nail through the bottom edge of the top plates and into the rafters. The rafters should be spaced equally throughout the roof, with no more than 16 inches between each one
  5. To reinforce the front margins of the rafters, cut a six-foot-long two-by-four board and nail it to them. The fascia board is shown here. Sheathing or oriented-strand board covering the walls and ceiling of the shed should be half-inch plywood or oriented-strand board. Fill in the sheathing around the perimeter of the walls and roof with 30-pound roofing felt. With a hammer stapler, staple the felt to the sheathing every 6 inches starting at the bottom of the walls and roof and working your way up. 1 inch should be left between the paper’s edges. Your chosen material for the shed’s side and front walls will be used to complete the structure. Siding and wood are both possibilities. The fascia board should be primed and painted. Install the shingles on the roof in the proper order. Begin from the bottom of the roof and work your way up to the top of the structure. In each row, stagger the shingles such that the joints overlap each other. Cut strips of rolled fiberglass insulation to fit between the wall studs and the rafters of the roof structure. Place the insulation in the desired location with the paper or foil facing inside, then staple the edge of the foil or paper to the wood using a staple gun. The insulation helps to keep the water heater from being iced over. Install the shed’s doors and secure them in place.

The Drip Cap

  • Despite the fact that a water heater is a necessary equipment in your house, it is also an item that may take up a significant amount of room. The fact that your house is somewhat modest in size and you need to utilize the space you have available might present a problem. It is possible to safeguard your water heater by building a lean-to water heater shed that is attached to the exterior of your home. In order to ensure that there is 3 inches of slab on either side of the sill plate, place the rear sill plate onto the slab up against the side of the house and center it. Making use of untreated timber, construct the top and bottom plates for the front wall of the shed. The jack studs should be placed on the sides of the door frame to provide the structure additional strength
  • And Into each end of the bottom plates, nail a wall stud to create a frame that resembles the letter “U.” Placing one of the frames flat on the ground, aligning one of the top plates with the outside stud, and driving two nails into each stud through the top plate will complete the project. Do the same thing on the other side. Remove the top and bottom plates, which should be each 6 feet long, and four wall studs, which should be each 8 feet high
  • In a zigzag pattern, raise each wall frame onto its appropriate sill plate and nail it to the sill plates every 6 inches on the inside of the frame. To make the shed stronger, nail the end studs of each neighboring wall together at the corners. The string line should be traced onto the studs on the side walls. To build the roof rafters, start by making a template board. To reinforce the rafters, cut a 6-foot-long two-by-four board and attach it to the front corners of the beams
  • 1 inch should be left between the paper’s edges. Siding and wood are among the available options. Put the shingles on the roof and fasten them in place.

How to Build a Water Heater Enclosure [Indoor & Outdoor]

A water heater that is left open in your home may detract from the overall aesthetic of your home. A water heater enclosure is a fantastic solution in this situation since it allows you to conceal your heater while keeping your home appearing beautiful. You may have made the decision to install a water heater cover at this point. But keep in mind that before you install a water heater cover, you should be familiar with the many types of water heater enclosures. Knowing everything there is to know about heater covers will assist you in selecting the most appropriate and finest heater enclosure.

So, read on to find out more.

What is a Water Heater Enclosure

Generally, a water heater is installed in the basement of a home. The basement may be utilized for a variety of other things as well. As a result, keeping the water heater door open can impair the view of the room while also raising concerns about the heater’s safety. To keep the water heater hidden from the outside world, a water heater enclosure is installed. We will examine the following topics to assist you in making the best decision from the numerous types of water heater enclosures available:

  • A water heater enclosure, several types of water heaters, and different types of water heater enclosures How to construct an enclosure for a water heater that can be used both indoors and outside

We believe that if you read the entire essay, you will have gained sufficient knowledge to evaluate the entire possibility of water heater enclosure for yourself.

Types of Water Heater

A water heater is not something you purchase on a regular basis. Because of this, it is important for you to understand the many varieties of them in order to select the most appropriate selection for your needs. The kinds are as follows:

  • Electric water heaters, conventional water heaters, storage tank water heaters, tankless water heaters, outdoor water heaters, outdoor tankless water heaters, and other types of water heaters are all available.

Water Heater Enclosure Types

Different types of water heaters need the use of different types of water heater enclosures. There are two classifications:

  1. A water heater enclosure for the outside
  2. A water heater enclosure for the inside

Let’s go on a guided tour of the facility.

Water Heater Enclosure Outdoor

There are two types of outdoor water heaters available:

Outdoor Water Heater Enclosure

Many houses have a water heater that is located outside the living room. You’ll need an outdoor water heater enclosure shed to keep it safe from various elements outside the building.

Outdoor Tankless Water Heater Enclosure

There are several advantages to using an outdoor tankless water heater.

It is a little heater that allows you to make better use of your available space. It includes an aluminum built-in outdoor water heater closet that is meant to survive extreme weather conditions such as high-speed winds, snowfall, and other natural disasters.

Water Heater Enclosure Indoor

A water heater that is left open in your home may detract from the overall aesthetic of your home. There are two alternatives for water heater enclosure ideas that you can use to conceal a water heater in a kitchen or any other area, or to design the appearance of the enclosure.

1. Water HeaterCover

Covering your water heater with drapes or screens is a good option. These are the most affordable and straightforward enclosures.

2.Complete Enclosure

As far as a complete enclosure for your water heater is concerned, you have two alternatives to select from. These are the ones:

Cabinets

These are the ideal enclosures to use in a basement or a kitchen, according to our research. They are available in a variety of formats, including

  • Water heater enclosures made at home
  • Vinyl water heater enclosures
  • Wooden water heater enclosures

Closets

This is the most effective method of concealing your indoor water heater altogether. The doors to the water heater closet are always painted to match the color scheme of the rest of the space. Because of this, placing your water heater within the closet has no effect on the overall appearance.

See also:  How To Take Water Filter Out Of Frigidaire?

Water Heater Enclosure Building and Installation

A totally concealed indoor water heater is the most effective solution. Always make sure that the doors to the water heater closet are painted in the same color as the rest of your home. Because of this, placing your water heater in the closet has no impact on the overall appearance.

How to Make an Outdoor Water Heater Enclosure

In order to construct the water heater enclosure outside the home, you must first construct the foundation. The procedure is comprised of the following steps:

  1. Paint the ground to indicate the location of the parameter
  2. Dig the marked-up ground to a depth of 4″
  3. Overlay landscape cloth over top of the earth
  4. Pour some gravel and revar into the concrete to give it more strength
  5. Build a three-foot-tall wooden frame to surround the hole. sand the concrete surface to a smooth finish

It is now time to begin construction on the shed. Examine the procedure one step at a time. To link the wall frame and concrete slab, cut two steel boards to the appropriate lengths. The backplate should be placed on the slab against the house and secured with masonry screws. Step 2: Step 3: Align the outer edge of the side plate with the outer edge of the slub on the black plate. 4. Cut the top and bottom plates so that the top plate and two bottom plates are each 6 feet and 1 foot in length, respectively.

  1. Step 5: Cut two jack studs and four wall studs for the jack studs.
  2. Step 6: Place one of the frames on the ground and align the top plate edge with the outside stud.
  3. Do the same thing on the other side.
  4. Step 8: Attach the rear wall frame to the wall.
  5. Step 10: Construct the rafters for the roof.
  6. The front and side walls should be finished with wood or siding, as shown in Step 12.

How to Make an Indoor Water Heater Enclosure

It’s now time to start working on the shed construction project. Examine the procedure step by step. To connect the wall frame and concrete slab, cut two steel boards to the proper lengths. The backplate should be placed on the slab against the house and secured with masonry screws. Step 3: Using the outside border of the black plate as a guide, place the side plate onto the slub. 4. Cut the top and bottom plates so that the top plate and two bottom plates each remain 6 feet and 1 foot in length, respectively.

  • Measure and cut two jack studs and four wall studs for the jack stud framing.
  • Using two nails through the top plate, secure one of the frames to the ground by aligning one of the top plate edges with one of the outside studs.
  • The top and bottom plates should be aligned in the same manner.
  • Finish assembling the door frame in steps 9 through 12.

Tenth step is to construct roofing trusses and rafters. A support board to cover the roof and walls is nailed to the frame in step 11. The front and side walls should be finished with wood or siding, as shown in step 12. Putting in the water heater door is step number 13.

  • Building a frame after taking sufficient measurements, for example, a square-shaped frame for a square water heater
  • Make sure that the side frames are complete. Join the outer layer of cardboards together with sufficient dimension
  • Add the enclosure door to the mix. Fix any trims that are required to keep the frame sturdy. If you have anything else you wish to include in the enclosure, attach it here.

Always remember that this is a simple DIY water heater construction project. If you wish to install one of the ready-made enclosures available on the market, make sure to read and follow the user manual that comes with it to ensure that the enclosure is correctly installed. FAQ

Can a water heater touch the wall?

Always remember that you are just going through the procedure of installing a water heater at home. To correctly install any ready-made enclosures from the market, make sure to read the user manual that comes with the enclosure and follow it step-by-step to complete the installation. FAQ

Is it ok to enclose a water heater?

It is entirely up to you whether you want to cover your water heater or not. It’s possible that not enclosing it may make your space appear cluttered. As a result, it is preferable to enclose the heater by constructing a wall around it and then decorating it by matching it with other household equipment.

Do water heaters need ventilation?

Water heaters burn natural gas or liquid propane (LP), which necessitates the installation of ventilation systems; this is referred to as the combustion process. Combustion increases the amount of heat, exhaust gases, and moisture produced. If the water heater is not equipped with ventilation systems, the byproducts will remain in the house and may harm the environment.

Can a power vent be added to a water heater?

Combustion refers to the process of burning natural gas or liquid propane (LP), which necessitates the use of venting systems. Heat, exhaust gases, and moisture are produced by combustion. As long as the water heater is not equipped with ventilation devices, the byproducts will remain in the house and may harm the environment.

How close can things be to a water heater?

It is necessary to remove the area surrounding the water heater since putting anything around the water heater might pose a safety hazard. Water heaters are powered by electricity or fuel, such as natural gas or propane, which is very combustible. As a result, it’s critical to ensure that your water heater has enough space (about 18 inches) around it to allow for adequate ventilation.

Do you need an outdoor water heater enclosure shed?

Outdoor water heaters are often constructed with an aluminum casing that allows them to survive adverse weather conditions such as rain, high winds, snowfall, and other calamities. As a result, the usage of an enclosed shed is not required. Even yet, if you want to provide your water heater with more safety while also decorating it to match your home’s décor, you may install an outdoor water heater enclosure shed.

What is the size of your water heater?

If you need to figure out what size water heater you need, the first step is to calculate how much hot water you use on a daily basis in your household. For those who are interested in knowing how to calculate the average, the following graphic may be of assistance:

  • The volume of hot water required for your daily activities should be calculated first if you want to figure out what size of water heater you’ll be needing. For those who are interested in knowing how to calculate the average, the following graphic may be of use to you:

Can you paint near a water heater?

Cleaning and keeping the area around a water heater free of combustible materials are important precautions. Paints that are inflammable should be used around the heater if you plan on painting around it, otherwise the fumes produced by the heater might pose a fire threat.

How do you get hot water at end of the house?

Cleaning and keeping the area around a water heater free of combustible materials is essential.

Paints that are inflammable should be used around the heater if you plan on painting around it, otherwise the fumes produced by the heater might pose a danger to your safety.

Where should you place your hot water heater?

You should situate your hot water heater against one of your home’s outside walls, if possible. Perhaps the garage or basement would be the ideal location for this. However, no matter where you store it, be sure to leave enough space around it to provide for the needed clearance area, which is around 12″ to 18″ around your water heater.

How do you hide your water heater?

A water heater has the potential to make your home a little cluttered and to harm the appearance of your home’s interior design. Water heater enclosures such as covers, screens, cabinets, closets, or heater blankets may simply be used to conceal your heater in order to prevent this situation.

Does a hot water heater have to be perfectly level?

Yes, properly flat ground is required for the installation of a hot water heater. This will allow the heater to operate at peak performance while avoiding any undue pressure on the joints.

Can a water heater be installed outside?

Yes, it is possible to place your water heater outdoors. However, not every type of water heater is the same. Only a few specific types have the capacity to withstand adverse weather conditions such as snowfall, rain, strong winds, and so on. It is also possible to install electric and gas tank water heaters outside if you provide them with adequate shelter, although this is not recommended.

Summary

Throughout this post, we want to guide you through the process of building a water heater enclosure and selecting the best water heater enclosure for your home. Hopefully, you now have a clear understanding of how to construct your water heater cover. However, if you do not want to deal with this chore, you may get a heating cover from the market. Alternatively, you may purchase one of the best water heater blankets, which are far less expensive to purchase than making a cover. In exchange, the heater blanket will not only conceal your heater, but it will also save you $200 a year on heating expenses.

Because of the additional insulating layer provided by a high-quality water heater blanket, the heater will not lose heat.

It’s as easy as that!

The Outdoor Water Heater Enclosure: A Complete Guide

Do you have a hot water heater that you can use outside? If this is the case, it is critical to take steps to avoid unintentional burns. This article will instruct you on how to construct a safe and effective enclosure for an outdoor water heater. It should be one that will keep your family safe from the hazards of scorching water.

What is a water heater enclosure?

A water heater enclosure is a metal cabinet that holds your water heater. It is made of steel. It functions in the same way as the heater’s wall frame. Enclosures for exterior heaters should be installed to keep the device safe from the elements and corrosion over time. In addition to protecting it from potential injuries or damage caused by an accident involving children, dogs, tools, and other items, it should be maintained for curb appeal and to withstand bad weather conditions. Additionally, enclosing your outside electric heating system will offer you with a more aesthetically pleasing enclosure.

It is also necessary to have a secure location to keep the water heater’s electrical cable and gas orifice. Apart from that, it will safeguard your new water heater and provide you with more room because the heater may be installed outside.

Considerations when building outside water heater enclosure

When selecting a hot water heating enclosure, it is important to consider the following factors. How often will it be used, as well as your climate (are you in a region with a lot of precipitation) are all important considerations. How often will there be snowfall throughout the course of the year? Is the enclosure strong enough to handle all of these problems? The best enclosures, after all, do this. The following are some concepts for outdoor water heater enclosures, as well as some considerations:

  1. Take into consideration the place where you intend to construct your enclosure. Decide whether you want your enclosure to be made of wood, vinyl, or metal
  2. And Figure out the size of your outdoor hot water heater and how much space it will take up in your enclosure. Make an appointment with an electrician to install electrical outlets in the location where you intend to install your hot water heater. Install insulation around pipes that are exposed to the outdoors in order to prevent them from freezing during the cold winter months. Fill up any cracks or gaps in walls with wire mesh or window screens to keep pests out during the summer months.

Types of outside water heater enclosures

A variety of outdoor water heater enclosures are available, including the following: a frame-built enclosure is made of a wood frame with metal panels on the exterior and insulating material on the inside. a frame-built enclosure A vinyl coating can also be used to guard against the effects of the weather or rust. Outside water heaters can also be built entirely of metal, with steel panels, hardware cloth (a sort of metal screen), and insulation as part of their enclosure. Outside electric water heaters can be housed in a robust wooden structure with mesh walls on the outside of the building.

It is possible to build a cabinet entirely of metal or vinyl that will be mounted directly to a wall surface.

Different types of outdoor water heaters tank enclosures

Electric water heaters installed outside should be housed in a metal cabinet or galvanized steel. The interior has screened apertures for ventilation and insulation, whereas the outside does not. Depending on how the enclosure is oriented in relation to the prevailing winds, the entrance of the enclosure can be either hinged or sliding.

Gas tank water heaters enclosures

A gas tank water heater must be enclosed in order to function properly. Make certain that it is installed in a location where any gases from the exhaust or flue pipe will not be able to escape. In addition, proper ventilation should be provided in the enclosure. Additionally, make ensure that there is adequate clearance for servicing your hot water heater’s burners.

Outdoor tankless water heater enclosure

A gas tank water heater should be enclosed. Make certain that it is installed in a location where no gasses from the exhaust or flue pipe will be able to pass through. Additionally, appropriate ventilation should be provided in the enclosed space. Make ensure that the burners of your hot water heater have adequate clearance for servicing as well.

Can you install water heaters outside: What you should know?

There are many various types of water heaters available, and each has its own set of advantages and disadvantages. Similarly, while making this option, the exterior heater enclosure is an important factor to take into consideration.

The reason being that it will be highly apparent in your backyard or patio area. Some individuals use them outside, however not all of the types are suitable for this sort of application. In a similar vein, you must consider your available space, financial resources, and personal preferences.

Four water heater enclosure recommendations

  1. Electric hot water heaters installed outside should be housed in a metal cabinet or galvanized steel with screened apertures for ventilation and insulating space on the interior of the cabinet. The entry entrance of these enclosures can be either a hinged or a sliding door, depending on how they are oriented in relation to the wind. In order to prevent the escape of any gases from the exhaust or flue pipe, it is important to locate the gas tank water heater in an area that is not accessible from the outside. In addition, ensure that the enclosure has appropriate ventilation and that there is sufficient space for repairing your hot water heater’s burners. Even though they are less prevalent than their storage tank counterparts, outside tankless water heaters are still available. In reality, it is feasible to find both electric and gas-powered versions of this appliance. Larger residences cannot benefit from outside tankless water heaters because of their restricted power capacity. Tankless water heater enclosures for the outdoors should be made of metal or galvanized steel with screened apertures for ventilation and insulating space on the interior of the enclosure. The access door should have a hinge and be large enough to allow for movement
See also:  How Far Can A 1 Hp Pump Push Water?

FAQs:Common outside water heater:

The typical cost of moving a water heater is $5,000, and the cost of hot and cold lines may be as high as $80 per hose. The cost of hiring an electrician to place your home’s water heater outdoors might be too pricey. The average cost is $650, but you’ll wind up spending significantly more for labor, which is at least $140 per hour on average!

Is it a good idea to place my water heater in the basement or on the patio?

The typical cost of relocating a water heater is $5,000, with hot and cold lines costing upwards of $80. It might be pricey to hire an electrician to put your home’s water heater outside. The average cost is $650, but you’ll wind up spending significantly more for labor, which is at least $140 per hour on average.

Do water heaters need ventilation?

To be sure, proper ventilation for exterior water heaters is required, but caution should be exercised since excessive ventilation may result in overheating.

Can you enclose a hot water tank?

It is generally recommended that hot water tanks do not be enclosed, however it is feasible to construct an outside enclosure when necessary.

How much space do you need around a hot water heater?

At the very least, there should be two feet of clearance around the water heater. Outside electric hot water heaters, on the other hand, require extra air for combustion, whilst gas units rely on a chimney for combustion.

How do you hide your hot water heater?

What you’ll need is a water heater enclosure, and depending on the sort of water heater that you have, you may select from a variety of different enclosures. Similarly, when it comes to safety and aesthetics, the outdoor hot water heater enclosure is critical, so make sure you select one that is appropriate for your needs.

How do you insulate an outdoor water heater or waterproof the water heater closet?

The enclosure for an outdoor water heater should be attached to the home and be adequately insulated. Insulation and waterproofing are required for outside hot water heater enclosures in order to guarantee that the structure of the enclosure does not deteriorate. We have a range of outdoor water heater enclosures to choose from to help keep your family safe from mishaps. Whether you want an enclosure for a tankless or a typical hot water heater, we can design and build the ideal enclosure to meet your requirements and budget!

If you want any information, please contact us immediately.

Conclusion

We have a range of outdoor water heater enclosures to choose from to help keep your family safe from mishaps. Whether you need one for a tankless or traditional hot water system, we have you covered. The Definitive Guide to Choosing the Best Indirect Water Heater The best-selling product on Amazon.com

Outside Water Heater Enlocure

The bottom plate is the only piece of pressure treated wood that you will require. Pressure treated plywood should not be used for the walls or the framework of the structure. If you do, you’ll need to use only ACQ-approved fastners, or else they’ll rust away in a year or two. It would be better to have a row of blocks resting on that slab, followed by a top plate, before constructing the structure. If this is not done, the sheathings will decay due to the proximity to the grade. I get to demolish homemade pump homes at least four or five times a year.

  • It is more cost effective in the long term to construct something correctly the first time rather than having to redo it all afterwards.
  • The frame is the same, but the size is reduced.
  • The original enclosure has been in place for at least 5 years, and the wood is still in excellent condition.
  • I am removing the old wood off the sides of the house and replacing it with 1/2 inch plywood “PT is a ply.

Are the codes for the use of ACQ certified fasteners uniformly applied throughout the country? The point is that PT performs far better in Florida weather and termite resistance. Will construct twin doors out of 3/8″ plywood and 1″ x 4’s “a ring around the perimeter

4 Ways to Hide Your Water Heater (& 3 Outdoor Options)

Are you looking for ways to conceal an unsightly water heater? A tank-style gas or electric water heater has a life expectancy of between 8 and 12 years, depending on the manufacturer’s recommended service life. That’s a long period of time to be forced to gaze at an unattractive water heater! As a result, it would be ideal if you had a dedicated storage space for it. Furthermore, some hot water heaters are not particularly aesthetically beautiful, which might detract from the overall appearance of your home.

This includes the following:

  • Install a decorative screen or room divider to conceal it
  • Place your water heater in a closet
  • Or construct a cabinet enclosure to conceal it.

The size of the water heater will determine which option you will select. They may contain anything from 20 to 120 gallons of water, with the majority of houses having a 50-gallon water heater. You will learn how to conceal your water heater in the next sections of this article.

How to Enclose a Water Heater?

When it comes to enclosing your water heater, you must decide whether you want a total enclosure or whether you prefer a partial or moderate amount of coverage.

1. Curtains are a Budget-Friendly Option

A curtain is still the most straightforward and straightforward method of concealing your water heater. The curtain serves as a separator and has the ability to be moved to the side. All you’ll need is a long curtain, a curtain pole, and curtain hooks to complete the look. In most circumstances, you can complete this task for less than $20. Depending on your interior design, the curtain can be either ornamental or basic. Some folks even opt for a plain piece of clean cloth as a substitute. It is necessary for the curtain to run from top to bottom in order to function properly, but it cannot be flush against the heater.

Choosing to do so is an option if you live in a rental flat because it may be taken down when you relocate.

2. Incorporate a Screen or Room Divider

Due to the fact that they do not completely surround the water heater, these solutions are more like coverings. Generally speaking, there are two types of water heater covers. Curtains or screens are used to cover the windows. A simple screen may do wonders in terms of keeping the water heater out of sight from the general public. Because ornamental displays might draw attention, you might choose a more straightforward screen. Contrary to curtains, which people associate with seclusion, elegant screens draw attention and compel others to examine them since they appear to be a part of the furniture itself.

Room dividers and screens are simple to install and reasonably priced.

3. Build a Closet

Water heaters are housed in customized closets that provide a complete unit enclosure. Create a customized closet based on the measurements of the unit you are working with. The closet will undoubtedly appear out of place if it is located in a high-traffic area of your home, and this must be taken into consideration. It is possible for the closet to appear planned and contrived. Don’t forget that the main idea of concealing your water heater is to make it more discrete and in keeping with the general design of your room.

In the laundry room, basement, or even in the kitchen are some examples of where you may put it. It is more durable to utilize a closet, and you may lock it to prevent the heater from posing a danger to anybody in the house.

4. Build a Custom Cabinet

Cabinets are more discrete than closets since they are smaller. They become a little more adaptable in terms of where they may be placed without being an eyesore as a result. An unfinished basement or a kitchen are both suitable locations for cabinets, which can be either recessed or freestanding. Although a hardwood cabinet is available for purchase, many individuals choose to utilize an all-metal unit instead. They are long-lasting, and they make greater use of available space. You may even build a water heater cabinet that you can store in a closet for further security and safety.

Other Options to Make Your Water Heater Less Noticeable

It is possible to install the water heater outside. However, you will have to pay for the construction of the structure that will contain the water heater. You will be responsible for the cost of the plumbing and piping system that will connect the outside heating enclosure to the house. Decorative outdoor water heater enclosures may be placed on your patio, deck, or garden as a focal point. The good news is that having the outdoor structure allows you to free up a significant amount of floor space within your home.

  1. Tank water heaters should only be used indoors, not outside.
  2. Steel Enclosure for the Outdoors It is possible to have the heater incorporated into the wall in order to keep it out of sight.
  3. This is a notion that is recognizable to those who work in commercial buildings or hotels.
  4. The primary difficulty with this scenario is that any damage to the heater might cause the wall to become unstable without you even realizing it.
  5. Consider this a reverse closet, in which the water heater is housed in an internal closet but the door is located on the exterior of the building.
  6. Outdoor tankless water heaters operate on a gas-fueled burner system that heats water immediately when the faucet is turned on.
  7. Consequently, cold water enters the tank by a dip tube, where it is heated and stored until the hot water tap is turned on.

With a tankless water heater, you can have hot water on demand rather than having to wait for it to be heated in the tank. A tankless water heater is an excellent choice for a small area. Tankless water heaters are available in a range of configurations, including electric and gas.

What to Consider When Hiding Your Water Heater

When you turn on the tap on an outdoor tankless water heater, the water is heated immediately by gas burners. This is in contrast to a tank heater, which has heating components built into the tank itself. Consequently, cold water enters the tank by a dip tube, where it is heated and kept until the hot water faucet is turned on. With a tankless water heater, you can have hot water on demand instead of having to wait for it to be heated in the tank. For compact spaces, tankless water heaters are an excellent option.

2. Safety

Check to verify that the enclosure is safe before entering. No sharp edges or corners should be present, as they might be dangerous in the workplace. In addition, if the enclosure is going to be outside, it should be weatherproofed. The materials that you employ in the enclosure’s construction should not come into contact with the water heater and should allow for easy access to maintain it. In order to ensure proper clearance between the heater and the enclosure, a 12-inch space should be maintained.

The water heater is almost always located in the basement of the house where it was built.

For gas water heaters, outdoor steel enclosures are a popular choice since they are weather resistant and provide access to the vent flue from the top of the enclosure.

3. Plumbing

Check to verify that the enclosure is safe before proceeding. Any edges or corners that are potentially hazardous should be avoided. It is also recommended that if the enclosure is to be used outside, it be weatherproofed. The materials that you employ in the enclosure’s construction should not come into contact with the water heater and should allow for easy access to maintain it. To ensure proper clearance between the heater and the enclosure, a 12-inch space should be maintained. The heater must have enough clearance on all sides to be safe.

Because there is normally relatively little traffic in the region, the basement will serve as a good hiding place unless it is always in use.

4. Cost

Choose a pre-fabricated enclosure that is strong enough to resist the weather if you do not want to build one from scratch. Outdoor enclosures are often more expensive than interior enclosures, mostly due to the fact that the materials used to construct the enclosure must be weather-resistant. The good news is that concealing an unsightly water heater does not have to be a costly endeavor. Choose a curtain or screen rather than an enclosure and you will save a significant amount of money on your project costs.

You can build a screen at a reasonable price using inexpensive panels.

A closet or cabinet does not have to be expensive to be functional. However, you must choose a contractor who is well-versed in the standards for building and installing water heater closets to construct one for you that meets all of the necessary requirements.

5. Accessibility

When concealing a water heater, it is vital that it be easily accessible. In the event that you are without hot water, you should be able to get to it for water heater maintenance or to make repairs.

6. Location

When concealing a water heater, accessibility is crucial. In the event that you are without hot water, you should be able to get to it to do water heater maintenance or make repairs.

7. Durability

The material you chose should provide you with a reasonable number of years of service. That is one of the reasons why most homeowners prefer outside steel enclosures. It is recommended that you use treated or decay-resistant wood when constructing an outdoor wood enclosure, as well as to paint the enclosure.

Conclusion

Keeping the water heater hidden It’s acceptable if you do it with the proper materials, in the proper location, and with the assistance of a professional. However, because many people do not adhere to construction code standards or utilize low-cost materials, the procedure is frequently viewed as a curse by others. When some people decide to take on a DIY project, they often end up ruining it and being stuck with an eyesore of a cabinet or closet in the most visible locations. It is generally recommended that you hire a professional to correctly enclose your water heaters.

Sources: Some Practical Guidelines for Hiding Your Water Heater in Your Home How to Install a Water Heater Enclosure DISCLAIMER: The information provided on HomeInspectionInsider.com is not intended to be professional advice.

It is owned and operated by Hubert Miles who is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by placing advertisements and links on their websites that direct traffic to Amazon.com (hereinafter referred to as “Amazon.com” or “Amazon.com Associates Program”).

Hubert Miles receives a commission for recommending visitors and commerce to these businesses.

Manufactured Home Hot Water Heater Enclosures Guide – 7 Shopping Factors To Check For

Many homeowners choose to install their water heaters outdoors rather than indoors. Because of the necessity to conserve space in prefabricated or mobile homes, this option is particularly appealing to those who live in them. Outdoor heaters are susceptible to denting, corrosion, and other types of damage as a result of the harsh elements. As a result, if you currently have a water heater placed outside your home, there is a good chance that you have contemplated covering it with some form of protective cover.

Later in this book, we’ll go over four water heater enclosures that are very stunning and worth considering. But first, let’s have a look at the considerations you should bear in mind when making your selection.

Seven Factors to Consider when Selecting a Water Heater Enclosure

What is the capacity of your water heating system? You’ll need an enclosure that’s large enough to accommodate the heater. The most accurate approach to determine the size of your heater is to look at its capacity, which is the total amount of gallons it can accommodate. Of course, the larger the enclosure, the greater the capacity.

See also:  How To Replace Water Pump On 2004 Chevy Silverado?

2. Material of construction

The material used in the building of the enclosure should provide you with some insight into its efficacy. It simply passes unmentioned that, due to the fact that the enclosure will be exposed to the elements, it must be constructed of a rot- and rust-resistant material. Galvanized steel is the most widely used material since it is safe, easy to work with, and lasts longer than other materials because it is durable.

3. Positioning

When it comes to electrical devices, they may be unpredictable at times. You never know when your water heater will fail and become a safety threat either inside or outside your house. Because of this, the enclosure’s placement is crucial. The location of the heater might have an impact on the amount of time it takes for emergency responders or a maintenance specialist to access it and solve the problem. Additionally, the enclosure should be large enough to allow the electrician to work comfortably while doing routine repair and maintenance inspections.

4. Aesthetics

No matter whether you choose to place your heater indoors or outside, aesthetics are vital considerations. It ultimately boils down to one question: is the enclosure visually appealing? So, before you even consider purchasing and installing the enclosure, consider how the entire arrangement will seem from a variety of perspectives. You may like to keep the entire setup hidden or to have it stick out like a sore thumb from the crowd. Aesthetic concerns might be influenced by where the heater is placed in the room.

If the heater is in the garage or basement, you won’t feel awful about concealing it with a plain cabinet or basic drapes that aren’t particularly attractive.

5. Cost

Or, to put it another way, the enclosure must be reasonably priced. Enclosures differ in price from the lowest – which are simply curtains – to the most costly – which are galvanized steel cabinets – and everything in between. You only purchase items that you can afford.

6. Durability

You’re looking for something that will last for a long time. It is never inexpensive to replace them on such a regular basis.

7. Air circulation support

Water heaters require a significant amount of air supply in order to operate correctly and safely. The use of insulating materials on the surface of many tank-type water heaters is still another cause for this. Some heaters are covered with dry calcium-infused chemicals, which do not smell pleasant when they are smothered in tight spaces with little access to fresh air.

Fortunately, most of the enclosures available on the market nowadays feature air vents located somewhere on the walls or near the front entrance to allow your water heater to continue to breathe.

Two Reasons You Need A Water Heater Enclosure

There are a few of reasons why you might want to put a protective enclosure around your water heater.

1. You Want To Hide The Water Heater

An open water heater in your backyard may have an impact on the aesthetic of your home, and it’s typically not in a positive way. Similar issues arise when the water heater is used indoors; the water heater’s towing tank-like construction does not look nice in an interior setting. Sometimes the only option for getting rid of an eyesore is to build an enclosure around it rather than removing the entire unit.

2. You Want To Add Some Style

In most cases, leaving a water heater out in the open in your backyard will have a negative impact on the exterior of your home. Similar issues arise when water heaters are used indoors; the water heater’s large tank-like construction does not look nice in an indoor setting. Sometimes the only option for getting rid of an eyesore is to build an enclosure around it rather than remove the unit completely.

The Two Types of Water Heater Enclosures

An open water heater in your backyard can have an impact on the aesthetic of your property, and it’s typically not in a positive way. The same is true indoors; the water heater’s large tank-like form does not look nice in an interior setting. A temporary enclosure is sometimes the sole option for getting rid of an eyesore without having to relocate the complete facility.

1. Covers

They are the most basic and least expensive enclosures available. If you want to access your heater, you just slide the curtain aside on a string, just like you would with a regular window curtain. The first step is to measure the height and breadth of the entry, keeping in mind to give enough space so that the curtain does not sweep the floor under it when closed. Despite the fact that curtains aren’t the greatest enclosures you could buy for your heater, they function very well if the heater is situated in a garage or other partially completed space.

Screens

These basic dividers might be typical divider screens or tall standing shutters, or they can be made of other materials. If you are seeking for a beautiful cover for your heater, these are the best options available to you. The fact that they are freestanding in nature allows them to be relocated with relative ease. If you want to be creative, you may paint them, paper them, or leave them in their factory design if you so choose.

2. Complete enclosures

Cabinets are the finest enclosures for heaters that are put in finished basements or kitchens, according to the manufacturer. They are frequently constructed entirely of metal and have an industrial appearance. Wood cabinets are just as popular as metal cabinets when it comes to design. Cabinets can be freestanding or built into a wall or ceiling. These cabinets, whether made entirely of metal or entirely of wood, are significantly more expensive than cover-based alternatives, but they endure significantly longer.

Closets

When it comes to heaters, cabinets are the greatest option for those put in completed basements or kitchens. They are frequently constructed entirely of metal and have an industrial appearance.

Cabinets made of wood are just as popular as cabinets made of metal. Cabinets can be freestanding or built into a wall or a ceiling. These cabinets are significantly more expensive than cover-based alternatives, regardless of whether they are made entirely of metal or entirely of wood.

Four Water Heater Enclosure Recommendations

You may either install the enclosure yourself with the help of a DIY enclosure handbook or pay an expert to do it for you. If you decide to construct the enclosure from the ground up, this will be the case. You may, on the other hand, purchase an enclosure that has already been finished and just place it around the heater. Here are a few of the top enclosures now available on the market:

1.HoldRite QuickShed 80-Gallon Gas/Electric Tank 30″ Steel Enclosure

This enclosure was created for 80-gallon water heaters that were powered by gas or electricity. Because the components may be fitted into one other like a jigsaw puzzle, it is simple to combine them into a full enclosure unit. It is made of high-quality galvanized steel, which is resistant to tampering and the effects of the weather. Especially if your heater is being put in a busy area, the design is compact enough to save on floor space.

Features

  • It complies with code standards. Construction using galvanized steel
  • Simple to assemble with only the simplest of tools
  • It’s tamperproof and rustproof. Exceptionally well-engineered design
  • Screws provide for a more secure installation. Front panel design that is superior in that it has an access door for service

Pros

  • Enclosure with a tank capacity of 80 gallons
  • Large capacity enclosure Steel frame that is both durable and sturdy
  • Installation is simple.

Cons

  • It is not smart-compatible (i.e., it does not support Bluetooth or apps)

2.Rubbermaid Large Vertical Storage Shed

Dent-resistant and weather-resistant, this large and simple to construct water heater enclosure from Rubbermaid is a great addition to any home or business. The huge vertical storage structure is equipped with a strong-duty bottom that can sustain severe impact and is easily adaptable to nearly any type of wood shelves of your preference. It has a large storage capacity of 52 cubic feet, which is rather large. This shed provides ample storage room for garden and lawn equipment, trimmers, and a variety of other outdoor things.

Features

  • Storage capacity of 52 cubic feet (albeit the lock is not included)
  • Lockable doors (but the lock is not included)
  • Construction that is both heavy-duty and leakproof
  • Lawn upkeep

Pros

  • Despite its size, it is simple to install. It’s a reasonable size and doesn’t take up much room. You may install shelves on the internal walls of your home.

Cons

  • I wish this enclosure had come with its own set of bespoke locks
  • That would have been ideal.

3.Rinnai Tankless Gas Steel Water Heater Enclosure

Those searching for a simple enclosure for tankless gas water heaters may be interested in this enclosure, which is built with simplicity in mind. Three connected steel walls that can be simply built around the heater while yet leaving plenty of inner space for repair and maintenance are included in the package. The straightforward cover was created in such a manner that it can be installed on the underside of your tankless water heater without the need for any special skills.

Features

  • For use with the RL94 and R75 series
  • HE + pipe enclosure for use with the HE silver variants
  • Ability to install from the bottom

Pros

  • A straightforward steel cover that is simple to install
  • Steel structure for sturdiness

Cons

  • Dents and other household impacts are not resistant to this material.

4.Rinnai Tankless Gas Steel Water Heater Recess Box

Rinnai has been manufacturing water heater cover solutions for 45 years, and this is one of the covers that exemplifies the company’s knowledge and expertise. This aluminum cover is light enough to be readily constructed and dismantled while also being resistant to corrosion to a high degree of precision. It holds up surprisingly well against the elements and unauthorized tinkering. Because it is intended for recess installation, it will securely hold your tankless gas water heater against the wall, which is both aesthetically pleasing and space-saving.

Features

  • Constructed of aluminum
  • Seamless water/moisture seal flange that is included into the design
  • Front door that may be removed
  • Drainage slots for drainage
  • Lock ring

Pros

  • Insert the heater into the wall so that it is out of sight. The design is slim and lightweight, yet it is also strong and impact resistant. With the lock ring, you’ll have the much-needed security.

Cons

In the proper installation environment, enclosures perform flawlessly. The following are the blunders to avoid when putting them in:

1. Not considering the position of the pans and drains

Drip pans are frequently used in conjunction with tank-type water heaters. These pans are positioned in a location where a leak is more likely to occur, and if one does, it has the potential to do significant damage. Typically, the tank’s base is chosen for installation because it is a convenient location for connecting the pan to a drain pipe that will divert any leaking water into the earth. However, while erecting enclosures, we have a tendency to place greater emphasis on space than on anything else, and it is not uncommon for us to overlook the proper placement or future installation of pans and drains.

As a result, if you are installing a tank-type water heater, keep in mind the importance of pans and how their placement will affect the overall appearance of the enclosure.

2. Ignoring proper distancing between the heater and the walls of the enclosure

As previously stated, there must be enough space between the walls of the enclosure and the heater to allow for proper ventilation. If you push items too close together, it will be difficult for the repairman or yourself to get into the vehicle and perform some maintenance.

3. Failing to consider basic safety precautions

Whenever you are placing enclosures on your water heaters, it is critical to remember the safety measures to take. For example, it goes unmentioned that you should ensure that your electrical wire is properly installed and that you should avoid allowing them to come into contact with the enclosure’s metallic body. The majority of enclosures, particularly those in the cover and cabinet styles, are constructed of steel, aluminum, or other high conductivity materials. It is also important to ensure that the enclosure’s edges are not sharp enough to cause damage when they come into touch with the skin.

4. Thinking that the enclosure will boost energy conservation

Addition of an enclosure to the water heater just for the purpose of increasing its energy efficiency is a tempting proposition. Although the entire concept may appear to be effective in your head, it is really unrealistic in practice. The vast area between the walls of the water heater and the enclosure is densely packed with air, allowing heat to be transferred from the heater to the outside. Despite this, most enclosures nowadays, whether cabinet or cover-style, have vents installed on their front doors to allow excess water to escape in the case of a leak.

As a result, if your water heater is inefficient, do not install an enclosure in the hope that it would improve its efficiency.

Enclosing Your Water Heater

Addition of an enclosure to the water heater just for the purpose of increasing its energy efficiency is tempting. Although the entire concept may appear to be successful in your head, it is incredibly unworkable in practice, as you will see. The huge area between the walls of the water heater and the enclosure is densely packed with enough air to allow heat to be transferred from the heater to the outside. Despite this, most enclosures nowadays, whether cabinet or cover-style, have vents installed on their front doors to allow excess water to escape in the case of a leak.

Don’t bother installing an enclosure around your water heater if it’s inefficient because you believe it will help.

  • It is advisable to allow a suitable buffer zone between the enclosure’s wall and the heater’s heating element. Ideally, there should be adequate room for the repairperson to accomplish his or her normal repair and maintenance duties. At some time on the walls, you will also need to add double doors, which will be another expense. Removal of the old heater unit and installation of the new heater unit are made simple by the presence of two double doors. Furthermore, if your water heater is fueled by gas, twin doors are preferable to a single door since the unit requires a lot of fresh air to operate well.

2. Wall Framing

Keep a fair buffer zone between the enclosure’s wall and the heater’s heating element for safety reasons. Ideally, there should be adequate room for the repairperson to execute his or her routine repair and maintenance duties; At some point along the walls, you’ll also need to put in double doors. Removal of the old heater unit and installation of the new heater unit is made simple by the use of two double doors. Double doors might be preferable to a single door if your water heater is fueled by gas, as the device requires a lot of fresh air to operate well.

Conclusion

In order to protect your heating equipment from corrosion, denting, and other impact-based damage, water heater enclosures are vital to have installed. When deciding on the appropriate enclosure, consider variables such as the cost of the cover, the aesthetics, and the location of the enclosure. You may save money by constructing your own enclosure by purchasing a DIY guide and following the instructions. Better better, you may purchase a pre-fabricated enclosure and have it installed by a professional.

Leave a Reply

Your email address will not be published.