How To Turn On Electric Water Heater

How to Turn on a Water Heater (12 Precautions to Follow)

There are a plethora of different types of water heaters available on the market nowadays, which may be bewildering. In your new building, you may discover a tank water heater, a tankless water heater, or a hybrid water heater, among other options. Tank water heaters were formerly the industry standard and quite popular, but tankless water heaters are becoming increasingly popular for a variety of reasons, the most important of which is their mobility. When a homeowner desires hot water delivered fast to taps or appliances that are not near to the central heater, point-of-use water heaters are the most common choice.

The following is not a lesson on which type of water heater is the most efficient, as the title indicates.

No, we don’t want you to be scrambling around trying to find a professional for everything, even this.

So How Exactly Do You Turn on Your Water Heater?

The particular procedures you must do to switch on your water heater may vary depending on the type of water heater you have. The next section will explain what you should look for when choosing a water heater and how to properly maintain one. It is vital to note that each of these procedures is critical and should not be omitted or dismissed as inconsequential. Ready? Let’s get started!

How to Turn On a Gas Water Heater

To switch on your gas water heater, simply follow these steps:

Step 1: Check For Any Open Valves or Faucets and Close Them

Starting with a visual inspection, look for any valves or faucets that may have been accidently or intentionally opened while you were working on your tank. It’s possible that someone opened it to allow a small amount of fresh air into your hot water tank. When you’re getting ready to turn on the water heater, the first thing you should do is close all of the open faucets.

Step 2: Turn the Cold Water on

The next step is to switch on the cold water supply. The reason you’re doing this is so that your tank may be refilled. It is essential since the last thing you want to do is switch on your heater when your tank is still half-empty.

Step 3: Light Your Pilot Light

The pilot light on your water heater must be re-lit in order for your hot shower to function properly again. It is also critical to do so in order to avoid any mishaps caused by the discharge of gas.

Step 4: Turn on Your Gas Valve

If your valve is set to “pilot,” you will not be required to complete the pilot light stage as described above. All that is left for you to do is switch on your gas supply valve. At this time, the water heater should already be heating the water, and the burner should be turned on and ready to go.

If you verify this on your heater and it isn’t the case, you may need to go back to the pilot light stage and repeat the process from the beginning again. This post will conclude with a link to a detailed step-by-step instruction manual.

How to Turn On an Electric Water Heater

In order to switch on your electric water heater, follow these steps:

Step 1: Check for Any Open Valves, or Faucets Close Them Up

In the same way that you check your gas water heater to see if there are any open valves or faucets, you must also check your electric water heater to see if there are any open valves or faucets. Anyone whose door is left open should be closed as soon as possible.

Step 2: Turn the Cold Water On

Make certain that your tank is completely full with water before turning on the electricity. You do not want the heater to be heating a tank that is almost completely depleted. This might cause serious damage to your tank or perhaps the heater.

Step 3: Take Out the Safety Tag

In the case that you placed a safety tag over your breaker in order to prevent anyone from turning on the switch, it is now time to remove it. If the house is not yours, it is possible that the owner has placed a tag on the switch, so be careful to double-check. If you own the house, you need get familiar with this procedure in order to avoid electric shocks.

Step 4: Turn on the Breaker

Your water heater breaker is in good working order and is ready to be turned on right now. At this point, the water heater should start heating the water to the desired temperature. Some electric water heater types may not provide any visible indication that the machine is operational. Low sounds, on the other hand, should be heard to signal that the heater has begun to operate.

How to Turn On a Tankless Water Heater

If your water heater has not been damaged, it is safe to switch it on right away. As soon as you finish reading this, the water heater should start heating up. Depending on the kind of electric water heater, the machine may or may not provide any visible indication that it is operational. Low sounds, on the other hand, should be heard to indicate that the heater is operating.

Step 1: Turn on Breaker

Due to the fact that these types of water heaters are tankless (as the name indicates), you will not be required to fill it with water as you would with other types of water heaters as long as it is linked to the water supply. All that is required is that you just turn the breaker.

Step 2: Confirm Temperature

Because the heater operates on demand, you’d have to choose a temperature that’s comfortable for you. It will heat up in accordance with the temperature you select and will only begin heating up when you require it to do so. In order to avoid an accident when turning on your water heater, you must proceed with caution. Take note of the following safety measures before proceeding.

Precautions to Follow When Turning on Your Water heater

  1. Check for drips in the discharge pipe of your washing machine. It is possible that the pressure is too high
  2. If you see any drops, lower the pressure immediately (below 80 psi is low enough). Watch for the scent of leaking gas when you switch on a gas heater that hasn’t been used in a long time. Natural gas smells unpleasant for a good reason, and if you don’t know what it smells like, some people equate it to the stench of rotten eggs. This should be done before you turn on the pilot light. If there is a strong smell of gasoline, propane, kerosene, or any other flammable substance, do not re-light the fire. If you have a more recent heater, it is possible that it will prevent illumination from occurring. If you have to switch on your water heater because the pilot light has gone out, look for the source of the problem. Please do not attempt to switch the heater back on if the problem has not been resolved
  3. Test your water heater to see whether it is safe to re-light it and to see if the relief valve is operational. If you are using an electric heater, make sure there are no naked wires or debris. It is not recommended to re-light the heater until you have resolved the issue completely. You should try something different if you discover that your water heater has been tripping off no matter how many times you replace a fuse or reset the breaker. It’s possible that getting your water heater serviced is the best course of action. Keep a safe distance between yourself and the pilot light or gas valve when you’re igniting the pilot light or turning on the gas valve after that. Please keep your bare body and, in particular, your face, out of the picture! When delayed lighting happens as a consequence of a filthy burner or maybe an out-of-position pilot, you run the risk of being seriously burnt if you aren’t careful. Ensure that your burner is free of dust, corrosion, or dirt before proceeding with the pilot light. You should not use your gas stove if the burner is coated with dust, rust, or grime. Before you can ignite the burner, you’ll need to clean it or get it serviced properly. In order to ensure that the outer and inner covers of the gas valve are properly secured, check them first before turning on the gas valve. If you attempt to ignite the pilot light and the burner does not ignite, do not attempt to ignite the pilot light again. First and foremost, turn off the gas. If you don’t know how to do it, research up processes online until you find what you’re searching for. You can also enlist the assistance of a professional. Don’t forget to keep in mind that the manufacturer has provided you with a handbook. If you have any questions concerning a particular part, don’t hesitate to examine the manufacturer’s handbook. As a brief aside, never throw away the instruction manuals for any device or gadget you purchase in case of an emergency like this. If you have misplaced your manufacturer’s handbook, don’t despair
  4. There may still be a way out of your jam. Take note of the manufacturer’s name as well as the model number of your heater and check them up on the internet. They have a website, and you should be able to discover some useful information there
  5. Many water heaters have instructions attached to them by the manufacturer
  6. These instructions may also be useful in troubleshooting the water heater.

Finally

It shouldn’t be too stressful to turn on a new water heater, whether it’s for a new house or a new water heater. With the knowledge in this article, you should be able to turn on practically any water heater without encountering any difficulties. Was this information of use to you? Please share your thoughts in the comments section below.

How to Turn On Water Heater

Turning on a new water heater, whether it’s for a new house or a new water heater, shouldn’t cause too much worry.

With the knowledge in this article, you should be able to turn on nearly any water heater without encountering any difficulties. Were these facts and figures of assistance? Please share your thoughts in the comments section below!

Getting Started

Before we get started, we need to figure out what sort of water heater you have on your property. The procedures for installing an electric unit will be very different from those for installing a gas-fueled unit. You should also evaluate whether you want a storage-tank water heater or a tankless water heater.

How to Turn on an Electric Water Heater

The most essential thing to remember in this situation is that if a heating element is not completely buried in water, it can cause irreversible harm, therefore make sure the tank is completely filled. To do this, turn on a hot water faucet on a fixture that is close to the water heater. If you witness a constant trickle of water, you may be sure the tank is fully charged. A sputtering and hissing sound indicates that additional water is required in the tank. Check to see that the water inlet valve is fully operational.

  1. Flip the circuit toon for the matching circuit breaker. Wait (it will take several hours for the water to heat up)
  2. Your water heater may be set to a temperature of 120 degrees Fahrenheit by default, which is the setting that we suggest. Check your user’s handbook to see whether there is a knob (which may be hidden behind a cover plate) that you need to adjust to 120 degrees Fahrenheit, high temperature, or hot temperature.

How to Turn on a Gas Water Heater

This procedure is a little more time-consuming, and we dedicated a whole page to explaining it. The pilot must be ignited once the tank has been completely filled with water. For additional information, please see how to ignite a water heater pilot for more information, however here are the fundamental steps:

  1. To turn off the gas valve, first turn on the pilot light. Find the burner and turn it on. Prepare to activate pilot mode
  2. Switch on the pilot
  3. And light the pilot. Keep the gas pedal down when in pilot mode. Turn up the volume on the radio

You may also have a look at this video created by ehowhome.

What About Tankless?

On-demand water heaters, whether gas or electric, are simple to turn on and off. If you’re using gas, you’ll want to make sure the gas valve is closed before you begin. Transform the circuit, adjust the temperature, and finally release pressure by opening the gas valve. For electric appliances, all you have to do is flick the circuit switch, turn it on, and set the temperature to 120 degrees. There is no waiting period in either situation. You should be able to get hot water right away.

Safety First

It’s important to remember that dealing with gas and electricity has a certain amount of danger. Make sure to turn off the electricity while working on a water heater’s electrical system, and be cautious not to leave gas valves open when they shouldn’t be. One method to improve safety is to use well-known brands, such as Bradford White, in your construction. Resources that are related to this topic include: How to Turn Off a Water Heater (with Pictures) Reset the water heater if necessary. Instructions on How to Light a Water Heater Instructions on How to Drain a Water Heater How to Increase the Temperature of a Water Heater Is there a recommended temperature for the water heater?

How to Turn on a Water Heater

Article in PDF format Article in PDF format Regardless matter whether you have an electric or a gas water heater, you can switch it on without needing to seek a professional for assistance. An electric water heater requires the discovery and activation of the circuit breaker, whereas a gas water heater requires the lighting of the pilot light. One of the most crucial procedures is to make certain that your water heater is completely filled with water before turning it on for the first time.

  1. 1 Turn off the water supply and the gas valve, or the circuit breaker, if applicable. Turn the gas valve to the “Off” position, or check to see that the breaker switch for the water heater is not tripped at the main circuit breaker. To cut off the water supply, turn the valve that controls the cold water supply line that enters the tank (which is normally from above).
  • It is recommended that the breaker switch for your water heater be clearly labeled, but if it is not, turn off the main electricity.
  • 2 Empty and flush the tank to thoroughly clean it. To drain your water tank, connect a hose to the bottom of the tank, near the faucet, and turn on the water. Consider purchasing a hose that will be long enough to reach a nearby floor drain or utility sink, or perhaps all the way outside to the yard. Then, to begin the process of draining the water tank, open the drain valve on the tank. By opening a hot water tap next to the tank, you’ll be able to drain it more quickly while simultaneously keeping an eye on the development of the tank. Once more, open the cold water supply valve to rinse away any remaining residue or minerals from the tank.
  • Allow 5-10 minutes for the cold water to flush via the drain valve
  • If it is a newly installed tank, you may skip the flushing procedure. It is not necessary to connect the hose or open the drain valve, and you can check the level of the tank by turning on the neighboring hot water faucet – a constant stream of water without sputtering is the indicator.
  1. Advertisement
  2. s3 While leaving the water supply valve open, shut off the drain valve. Close the drain valve and remove the hose once the tank has been emptied completely and clean water is flowing out of it. After a few minutes, your water tank should begin to fill up again. Maintain an open tap on a nearby faucet to allow air to escape while the tank is filling
  3. 4 Keep an eye out for any open hot water faucets in the area. When your tank is completely full, you’ll be able to tell by the temperature of your hot water tap. When you see and hear a lovely, steady stream of water coming out of the tap, you know your water heater is fully charged. It is possible to hear spitting, which indicates that air is still being squeezed out of the tank. Once you have a constant stream coming out of the faucet, you may close it. Turn on the gas supply or the circuit breaker, if applicable. You’re now ready to switch on the water heater because the tank is completely filled. You should turn on the gas valve if you’re working with gas when you’re ready to ignite the pilot light, unless you’re working with electricity. In the case of electric water heaters, re-energize the circuit breaker. Advertisement
  1. 1 Adjust the temperature and on/off controls to the appropriate settings. Make sure the temperature control is set to its lowest level before turning on the water heater. This means that the On/Off control will need to be set to the “Pilot” position.
  • Please do not proceed until you have called your gas provider to report the smell of gas or rotten eggs
  • Otherwise, you might be experiencing a gas leak.
  • 2While starting a spark, press the pilot igniter button all the way down. While holding down the pilot igniter button, push the spark generator button to activate the pilot igniter. As a result, you should see a spark appear through the little glass window, indicating that the pilot light is operational
  • 3 Continue to push the pilot igniter button for 20-30 seconds at a time. Do not let go of the pilot igniter button until you see a spark appear on the horizon. Press it for 20-30 seconds longer than necessary so that it may heat up sufficiently before being released
  • If the spark generator is still not lighted after 30 seconds, you may need to click the button every 10 seconds until it is correctly illuminated.
  1. 4Put the control in the On position and adjust the temperature to the appropriate level. Turn the On/Off switch to the “On” position. Once you have reached your preferred temperature, adjust the temperature setting. The majority of individuals set theirs at 120 degrees Fahrenheit (49 degrees Celsius). You should now be able to view flames through the little glass window that has been installed. Advertisement
  1. 4Select “On” from the control panel and adjust the temperature to the appropriate setting (see illustration). Turn on the power by pressing the On/Off button. Then adjust the temperature setting to the temperature you choose using the dial. Temperature settings for the vast majority of individuals are 120 degrees Fahrenheit (49 degrees Celsius). Hopefully, by this stage, you should be able to see flames coming from the little glass window. Advertisement
  • 4Turn the control to the On position and adjust the temperature to the appropriate level. Turn the On/Off control to the “On” position. Then adjust the thermostat setting to the temperature you choose. The majority of individuals have theirs set to 120 degrees Fahrenheit (49 degrees Celsius). You should be able to see flames through the little glass window at this point. Advertisement
  • 2Remove any access panels that are no longer needed. It is possible that your water heater has access panels on the inside and outside that must be removed. To reach the pilot light in this situation, remove the access panels on either side of the pilot light. Typically, the access panels simply slide out of the way
  • 3 Press and hold the pilot button on the water heater for a few seconds. Maintain pressure on the pilot button in order to be able to turn on the water heating system. If your model does not have a dedicated pilot button, press and hold the On/Off control for four seconds. Light the pilot with a long-necked lighter to prevent it from exploding. The pilot supply tube is a tiny silver tube that is linked to the gas control valve. It may be found near the gas control valve. Follow the silver tubing all the way to the end, and then light the pilot using a long neck lighter
  • 5 Keep the pilot button held for 20-30 seconds before releasing it to continue flying. After you’ve lighted the pilot, keep your finger on the button for another 20-30 seconds to keep it lit. After the time has expired, you may progressively unplug the battery and the pilot should continue to operate as normal.
  • If your pilot light goes out, relight it by pressing and holding the pilot button for a longer period of time than you did the first time.
  1. 6Reinstall the access panels if they were removed previously. Remove any access panels from your water heater and replace them with their original positions. It is possible that if you do not do this, the flames will suddenly pour out of the orifice as a result of gas buildup and inflict significant harm
  2. 7 Set the on/off switch and the temperature control to the appropriate settings. Select “On” from the On/Off control and adjust the temperature control to your liking — 120 degrees Fahrenheit (49 degree Celsius) is the suggested setting. After you’ve finished configuring the settings, you should hear the water heater begin to heat up. Advertisement
  1. 1 After the hot water tank has been filled with water, turn on the circuit breaker for it. The circuit breaker that regulates an electric water heater must be located and turned on in order for the heater to function properly. Find a double-pole breaker with an amp rating equal to or more than that of the heater if your circuit breaker isn’t listed. The electric water heater may be turned on by simply turning on the circuit breaker
  • Once the hot water tank is fully stocked, turn on the circuit breaker for it. The circuit breaker that regulates an electric water heater must be located and turned on in order for the heater to operate properly. Find a double-pole breaker with an amp rating equal to or more than that of the heater if it isn’t listed. In order to turn on the electric water heater, simply turn on the breakers.
  • 2It may take many hours for the water tank to heat up completely. It will take many hours for your water heater to reach its full heating capacity, so check on it occasionally by turning on a tap to ensure that it is getting warm. The optimum temperature is 120 degrees Fahrenheit (49 degrees Celsius)
  • 3 Before turning on your tankless water heater, be sure the gas is turned off. It is critical to ensure that the gas has been switched off before turning on your tankless water heating system. In order to use a tankless water heater, it will be necessary to turn on the breaker or to turn on the switch
  • 4 Check the temperature and then switch on the gas to the tankless water heater to ensure it is working properly. Once the electricity has been turned on, you may modify the temperature by utilizing the temperature controller, which is often digital in nature. All you have to do now is turn on the gas supply
  • That’s all.
  • Tankless water heaters run on-demand, which means that they will only begin heating water when you really need it. Because these water heaters are tankless, you won’t have to worry about filling them with water.
See also:  How To Tell Hot Water Heater Is Bad?

Create a new question

  • To ignite an electric water heater, follow these instructions. Drew Hawkins1Answer from the Community It is not necessary to light an electric water heater. Locate and activate the circuit breaker that regulates the heater’s operation. Allow for a few hours for the water tank to heat up before using it. Check the temperature of a faucet on a regular basis to ensure it is getting heated. When the water temperature reaches 120 degrees Fahrenheit (49 degrees Celsius), the tank has reached its maximum temperature. Question What is the proper way to reset my hot water heater? Drew Hawkins1Answer from the Community Look for a red button with the word “Reset” printed on it on the side of the water heater. Some water heaters feature a reset button that is tucked down behind the thermostat for easy accessibility. When you’ve found it, push the button down hard on it. It is possible that it will produce a clicking sound when it resets. Question Do you know how long you’ll have to wait for the hot water to return? Drew Hawkins1Answer from the Community Gas water heaters can heat up a tank of hot water in around 30 minutes, according to the manufacturer. When it comes to heating the water in its tank, electric water heaters might take a couple of hours. Having hot water again will be available once the water tank has been heated.

Inquire about something There are 200 characters remaining.

Include your email address so that you may be notified when this question has been resolved. SubmitAdvertisement Thank you for submitting a suggestion for consideration!

  • In the case of drips pouring out of the discharge pipe, this might indicate that the pressure is too high. Reduce the pressure such that it is less than 80 psi
  • For a gas water heater, always check to make sure there isn’t a gas leak or rotten eggs smell before igniting the pilot light
  • Otherwise, the water heater might explode.

Advertisement

About This Article

Summary of the ArticleX Check to be that the water tank in your gas water heater is completely filled before turning it on. After you’ve done this, turn the knob on your water heater to the “pilot” position and, if your water heater has one, click the spark igniter button to start the water heater. If you don’t have a long-handled lighter, you may use a cigarette lighter to ignite your pilot. As soon as the pilot is ignited, flip the knob to the “on” position and adjust the temperature to your liking.

To understand how to replenish your water tank and switch on an electric water heater, continue reading this article.

The writers of this page have together authored a page that has been read 130,880 times.

Did this article help you?

There are a few procedures you need to take in order to get your electric hot water heater up and running. Prematurely activating the breaker or turning on the water might cause complications and perhaps damage the heating components. Not sure if you’ve arrived at the correct location? Please refer to the articles’Troubleshooting Electric Water Heaters ” and ” Troubleshooting Gas Water Heaters ” for detailed information on all water heater related issues. It is necessary to partially or fully drain the water from an electric water heater for a number of repairs on this type of appliance.

In the event that you did not deplete the tank but instead turned off the water, you should still follow the method for turning on the water to ensure that the tank is fully stocked before the electricity is switched on.

Close the Drain Valve

Drain the tank by closing the drain valve located at the bottom of the tank. Remove the hose that you used to drain the tank and clear up any extra water that has accumulated on the floor. Check to see that the drain valve is securely closed. Disinfect the surrounding region and the valve itself with rubbing alcohol. When the water is turned on, you’ll want to keep an eye on it to make sure it isn’t leaking.

Turn On the Cold Water Supply

Drain the tank and close all of the valves and taps in the home that you may have opened while doing the draining. Turn the cold water supply pipe at the top of the tank to the cold water supply position. At this point, you should be able to hear the tank filling up with water. On the hot water side of the tank, there should not be a valve installed. If there is one, be certain that it is operational. Wait for the water heater to completely fill with water before using it again. Check the water level by turning on a couple of taps and letting the air out to ensure the tank is full.

Turn On the Power

The electricity should have been turned off safely, and you should have tagged or “locked out” the circuit breaker that served as the water heater’s circuit breaker. You should follow this procedure whenever you work on anything that involves electricity in your house. For further information, see the articles “How to Shut Down an Electric Water Heater” and “Electrical Safety at Home.” After the hot water tank has been filled with water, turn on the circuit breaker for the hot water tank. After the water has been entirely emptied, it will take some time for it to warm back up.

When the elements start heating, you should be able to hear a buzzing noise. When this occurs, you will be notified that the water heater is operational. The water should be at least warm, if not hot, after one hour.

Summary

The actions outlined in this article should be followed for re-starting an electric water heater after it has been shut off have been provided. Turning the power back on too quickly might cause harm to the elements. To avoid difficulties, make sure to follow all of the instructions.

How To Turn On a Water Heater

The procedure for turning on a water heater is comprised of a few simple stages. Although it appears to be a straightforward task, there is a certain protocol that must be followed. For gas and electric water heaters, you will need to follow a distinct set of instructions. Propane water heaters will operate in the same way as natural gas water heaters. If you are unsure about the sort of water heater you have, go to the section titled ‘Water Heater Types’. Having doubts about whether or not this is the best answer for your problem?

See also:  Why Is My Tankless Water Heater Making A Loud Noise?

You may get information on recognizing your specific problem with an electric water heater by reading ‘Electric Hot Water Heater Troubleshooting.’ Hot water heater issues that are more broad in nature can be found under ‘Hot Water Heaters General Topics’ for further information.

Turning On a Gas Hot Water Heater

The following are the procedures to take while attempting to start a gas hot water heater, with explanations to follow: (1) Close any faucets or valves that are currently open. Then start by putting on the cold water faucet. (3) If the gas has been turned off entirely, re-light the pilot light. (four) If the gas valve was previously set to the ‘Pilot’ position, switch it to the ‘On’ position.

Step One – Close Open Faucets

In the event that you were working on your hot water tank, you should have opened a faucet in order to allow air to circulate through it. This inhibits the formation of an airlock in the system. You can now close the faucets until you are ready to re-connect the water supply.

Step Two – Turn On the Cold Water Supply

To prepare for re-igniting the gas and lighting the pilot, you’ll want to turn on the cold water faucet and allow the tank to replenish. When the tank is only partly full, it is not recommended to turn on the heating components again. At this time, the tank will be refilled with water, replacing any that was lost during the tank’s repair work and maintenance.

Step Three – Light the Pilot Light

In order to refill the tank before re-starting the gas and lighting the pilot, you need first switch on the cold water faucet. When the tank is only partly full, the heating components should not be turned back on. At this time, the tank will be refilled with water, replacing any that was lost during the tank’s repair operation.

Step Four – Turn the Gas Valve to On

If you were able to just flip your gas valve to the ‘Pilot’ position, you would not have needed to use the pilot light at all. Instead, you should be able to activate the gas by turning the gas valve to the ‘ON’ position.

At this point, the water heater should begin to heat the water in the tank. As a result, the burner should be turned on. You will need to follow the whole pilot lighting instructions if, for some reason, it does not work properly. For further details, see the page on “How to ignite pilot lights.”

Turning On an Electric Hot Water Heater

The following are the procedures to take while attempting to start a gas hot water heater, with explanations to follow: (1) Close any faucets or valves that are currently open. Then start by putting on the cold water faucet. (3) Take the lock out tag out of the breaker box and discard it. (4) Disconnect the hot water heater from the main circuit breaker.

Step One – Close Open Faucets

The following are the procedures to take while attempting to start a gas hot water heater, with explanations to follow. Open faucets and vavles should be closed. Then start by bringing up the cold water supply. (3) Take the lockout tag out of the breaker box and discard it. In the case of a hot water heater, turn on the circuit breaker for it.

Step Two – Turn On the Cold Water Supply

The following are the procedures to take in order to turn on a gas hot water heater, with explanations to follow: (1) Turn off any faucets or valves that are currently open. Then start by putting on the cold water supply. (three) Take the lockout tag out of the breaker box. (4) Turn on the hot water heater’s circuit breaker.

Step Three – Remove the Lock Out Safety Tag

This is the piece of tape that you should have placed over the breaker to warn anyone who attempts to get access to the panel not to switch on the circuit breaker. This is a safety measure that can help to avoid electric shocks and possibly death from occurring.

Step Four – Turn On the Water Heater Breaker

The majority of electric water heaters do not include an indication light to alert you that the appliance is operational. If you listen closely, you should be able to hear some clicking sounds, which signal that the heating components have been activated and the water is beginning to heat. At this point, the water heater should begin to heat the water in the tank. You should be able to get hot water in 30 to 60 minutes. Check one of the faucets to see whether the water is getting hot before turning on the water.

How To Turn On Water Heater? [Gas, Electric, Tankless Water Heaters Covered in 2021]

TanklessWaterHeaterExpress is sponsored entirely by its readers. Because I am an Amazon Associate, I receive money when people make eligible purchases. After the installation is complete, the installation specialist may switch on the hot water heater for a brief period of time. The question then becomes, what do you do when you are on vacation? The most prudent course of action would be to switch off the heater. However, shutting it off and then not understanding how to switch it back on may be a very perplexing experience.

However, if you have the proper instructions, turning it on will not be a tough chore to accomplish.

So, let’s get started with the how to switch on a water heater instruction.

How to Turn On Gas Water Heater?

1st step: close all of the valves. It is necessary to inspect all of the valves and faucets before you can begin the procedure. This will help to jumpstart the process. If you turn on the electricity while leaving the faucets running, pressure will build up inside the heater, causing it to malfunction. A whistling sound will be heard from within the heater if they are turned on and working properly. As a result, it’s advisable to turn on the water before shutting off the valves and faucets. Precautionary measures should be taken to ensure that there are no gas leaks present.

  1. Step 2: Allow the Coldwater to Flow Freely Next, switch on the cold water supply to the heater, which should take around a minute.
  2. When you turn on the cold water supply, the water that comes out of the faucet will go right into the tank.
  3. You must wait until the heating tank is completely full before turning it on.
  4. You will need to switch on the pilot light when you have finished with the previous step.
  5. After you have completed the appropriate procedures, you will need to go to the opposite side of the heater.
  6. It must be turned on in order for the heater to be prepared for burning.
  7. If at all possible, avoid direct hand contact and consider using gloves.
  8. Its purpose is to open the gas valve.

If you are unsure which way to turn to release the gas, have a look at the handbook and then proceed as directed. Depending on the brand, the valve may be turned in a different direction from the others. As a result, you must be certain before turning it on.

How to Turn On Electric Water Heater?

Step one is to inspect the valves. As you did with your gas water heater, you must apply the same thinking to this situation as you did with your gas water heater. Look for any and all of the facets that are attached to the heating element. Alternatively, if you see any of them have been turned one, simply shut them. Aside from that, you must also look for any valves that may be present near the heater. If you leave them open, the air pressure within the tank will rise, causing the inside components to break as a result of increased pressure.

  1. Step 2: Allow cold water to flow through the faucet.
  2. Always make sure that the heater is fully stocked with water before turning it on to save energy.
  3. This will prevent the water from being properly heated and performing as it should as a result.
  4. Wait for a period of time until the tank is completely filled with water.
  5. Electric water heaters are equipped with a safety tag, which we utilize to switch off the heater when necessary.
  6. As a result, you must carefully remove the safety tag before turning on the power.
  7. Make certain that you are adequately protected from electric shocks.
  8. One of the most crucial components of the electric heaters that we utilize is the circuit breaker.
  9. The heater should be turned on at this point if you have followed the other procedures correctly.
  10. This will allow the heater to be ready for use when it is needed.

How to Turn Tankless Water Heater On?

Valve inspection is the first step. Similar to the notion of what you accomplished with the gas water heater, you will need to apply it here as well. Look for any and all of the aspects that are linked to the heating system. If you see that any of them have been turned one, simply close them out of sight. Aside from that, you should also look for any valves that may be present near the heater itself. Keep them open because if you don’t, the air pressure within the tank will build up, causing the internal components to fail.

  1. Flowing Cold Water is the Second Step The next step is to turn off the cold water faucet.
  2. Because there is insufficient water in the heater, the same air bubbles will continue to accumulate.
  3. In order to allow cold water to enter the tank, gently open the valve and the faucet.
  4. the third step is to attach a safety tag.
  5. Someone who is not currently using the gadget cannot mistakenly switch on the heating.
  6. You should also ensure that your hands are completely dry and, if at all feasible, use gloves when working with sharp instruments.
  7. Circuit Breaker (Step 4) Another key component of the electric heaters that we employ is the circuit breaker.
  8. The heater should be turned on at this point if you have followed the previous instructions.

Circuit breakers must be connected and activated before any work can be performed. In this way, the heater will be ready to begin working immediately. It is necessary to hear low noises to know that the heater is ready to start if you do not have a circuit breaker.

What Precautions Do I Need to Follow?

  1. It is necessary to monitor the pressure that is accessible through the discharge pipe as soon as possible after starting the process. If there are drips, this indicates that the pressure is too high. Generally speaking, it should be anything less than 80 PSI. When you switch on the water heater, check to see that no one has used it in the previous few minutes before you do so. Because all of the gas valves may still be too hot to handle, and there may also be some risks of leakage, this is necessary in most cases. Always take a close check at the naked wires or the cutters that are present within the heater before proceeding. If you come across such a situation, fix it as soon as possible without turning on the water heater. Having an adiagnosis performed on the T and P valves is the next step that you must complete. As one of the most significant components of the water heater, it is worth mentioning here. Make certain that this valve is constantly in proper functioning order. Keep your distance from the gas valve for a few minutes after you have switched it on to avoid being electrocuted. It is possible that the gas is unstable and that there are minute leaks. Direct inhalation of the gas is not recommended due to its toxicity.

Final Talk

In any setting, whether at home or at work, it should be a standard practice to turn the lights on and off at regular intervals. It helps to keep a heater in good condition and safe to use. Nonetheless, if you are experiencing any technical issues when attempting to turn on your hot water heater, you may do a short diagnosis test. Look for the issue code displayed on the screen and then contact an expert to assist you. If the heater turns on flawlessly, it indicates that all of the sensors and valves are in proper operating order.

Please let us know if you are experiencing difficulties as well as you.

How to Reset an Electric Water Heater in Two Easy Steps

Turning it on and off on a regular basis, whether at home or in a professional setting, should become second nature. Heater health and safety are maintained when using this method. While turning on the hot water heater, if you encounter any technical issues, you can do a rapid diagnosis check. Look for the issue code displayed on the screen and then contact an expert to assist you. A flawlessly functioning heater indicates that all of the sensors and valves are in proper operating order. Please share your recent experiences on how to switch on a water heater with us in the comments section below!

Why Electric Water Heaters Quit

So, what exactly is the source of Hot-Showerus Interruptus? Alternatively, if you have an electric water heater, it is likely that the unit’s reset button has been activated. Those buttons have a tendency to trip at unpredictable intervals. However, it frequently occurs as a result of the following:

  • The thermostat in the device is not working properly
  • Even the reset button itself isn’t working properly
  • The high-limit switch, which is a component of the unit that prevents water from becoming excessively hot, is no longer operational. There is a short in the heating element. There’s a snag in the wiring someplace

Recall that the reset button on a water heater has a vital function: it interrupts power in the case of a malfunction, such as a power surge or a malfunctioning thermostat, to prevent further damage. If your water heater loses power on a regular basis, it is probable that there is an issue that needs to be repaired by a competent Culpeper County plumbing contractor. Please keep in mind that the combination of electricity and water may be extremely harmful, if not lethal. Never be afraid to bring in a professional to double-check your work.

Assuming you have this understanding, let’s follow through two easy steps to get it back up and running.

First, check your electrical panel.

Locate the circuit labeled “water heater” on your electrical panel (which is normally located in the garage, basement, or storage closet), and turn it on.

  • If the breaker is currently in the OFF position, flip it to the ON position. If it remains in place, you may generally conclude that everything that has happened has been an accident and that you can go about your business as usual. However, if the switch returns to the OFF position, either immediately or shortly thereafter, contact an electrician. If the breaker is currently in the ON position, flip it to the OFF position.
See also:  How Often To Change Fridge Water Filter

Then, push the water heater reset button(s).

You’ll locate a reset button on the back of your electric water heater somewhere. It is often crimson in color and is generally seen around the thermostat. It might alternatively be concealed behind a detachable metal plate on the device, which would then be concealed behind some insulation. Once you’ve located the button, press and hold it for a few seconds. While you have the access panel off, check to see if there is a second thermostat and a second reset button hidden within.

A professional should be called if the button trips shortly after you press it, indicating that something is not operating properly. If this is the case, the access panel should be replaced, and the necessary circuit breaker should be turned back on.

  • If the electricity to your water heater has been restored, you’re good to go. (Congratulations on your accomplishment!) Just keep in mind that it will take a few hours for the water in the tank to reheat. If your water heater is still not working, turn off the circuit breaker and contact us so that we can figure out what’s wrong and get the hot water flowing again. If your water heater begins to operate but the reset button trips again, turn the breaker back to the OFF position and call us for further assistance. As previously said, your reset button is a safety precaution, therefore if it continually tripping, there is something wrong with your computer.

Is Your Water Heater Trying to Tell You Something?

Taking a cold shower becomes (kind of) amusing all of a sudden. However, when it occurs again, it becomes a source of aggravation. We’d be delighted to come over and see what’s going on, so please contact us right away. You’ve earned some wonderful, hot baths!

When You Should Turn off Your Water Heater

When it comes down to it, a water heater is a really straightforward item. You can rely on a tank water heater to provide you with consistent hot water for 10-15 years — all it wants in return is for you to do some routine maintenance on it. However, there are occasions when the unit’s upkeep must be taken into mind. A common question we receive from consumers is, “Do I need to switch off my water heater if.?” The following are responses to three frequent circumstances.

When the main water supply is shut off

It is possible that the main water supply will be switched off in a variety of situations. When this occurs, many homeowners ask if it is safe to leave the water heater turned on or whether it should be turned off as well. Yet, turning off the water heater may not be absolutely essential in the majority of circumstances; however, doing so will not be harmful any way. However, there are two instances in which you should turn off the unit to avoid excessive pressure or heat from building up inside the tank: (1) When the unit is not in use; and (2) When the unit is in use but not in use.

  • It is possible that the main water supply will be switched off in a variety of situations, including emergencies. A common concern among homeowners when this occurs is whether it is safe to leave the water heater turned on or if it should be turned off completely. In most circumstances, it is not required to switch off the water heater, although it is not harmful to do so if you choose to. When you should switch off the unit to prevent excessive pressure or heat from building up inside the tank, there are two reasons to do so: first, you should prevent excessive pressure or heat from building up inside the tank by preventing the following:

When you go on vacation

When you travel on vacation or anticipate being away from home for a lengthy period of time, you should follow the standard procedures for preparing your house. You may make changes to your heating and cooling systems, program automated lighting, and place a hold on your mail. But what about the water heater in your home? While it may seem rational to turn off the water heater when it is not in use in order to conserve energy, this may not be as advantageous as you may expect. For starters, turning on and off the unit may be disruptive and difficult for the unit.

Instead, use the “VAC” mode on your water heater (which is a typical feature on contemporary water heater types) or lower the water temperature to 50 degrees Fahrenheit.

When there’s a leak

The unit should be turned off and the water supply should be turned off until the problem is remedied. A leak can occur for a variety of causes, including age or a valve fault.

Plumbers in Murrieta and Winchester, CA

If you have any further concerns concerning your tank or tankless water heater, or if you believe it’s time for maintenance or repair, call the local plumbing experts at Liberty Plumbing for assistance. If you’d like to book an appointment, please contact (951) 760-4215.

How to Reset an Electric Hot Water Heater

After the water heater’s electricity has been turned off, remove the metal plate that covers the thermostat by removing the two screws that hold it in place. Keep the screws in a safe place. There will very certainly be some sort of insulating layer underneath the plate. You should be able to see the reset button when you have removed the insulation. It’s most likely in the color red, and it could even be labeled “reset button” or something like. Firmly press the button in to secure it. This should cause the electricity to the heating element to be re-established.

Replace the insulation and make certain that the metal plate is secured with the screws that were saved from the previous step. Next, depending on how you shut down the electricity, either reconnect the plug to the socket or reset the circuit breaker to the “ON” position.

Step 3. Check to See if the Issue is Solved.

Watch your hot water for approximately a half hour to see if this has resolved the problem for you. Assuming that your hot water heater is operational, you should have hot water in approximately half an hour—and you will have spared yourself the expense of a professional visit. Reset the button on the other panel as well if the problem persists and your hot water heater has two panels, one on the top and one on the bottom, as shown in the illustration. Simply continue the steps in Step 1 (making sure to turn off the power again) and Step 2 to complete the process.

  • In the event that you still don’t have hot water after waiting half an hour, or if your water heater trips again shortly after, this may indicate the presence of a more serious problem.
  • A variety of factors might be contributing to the problem, including a defective thermostat, a faulty heating element, or loose or faulty wiring that is generating a short.
  • This is when you should contact a professional, such as Kay Plumbing Services, to help you diagnose and resolve the issue.
  • This will help to avoid potentially harmful circumstances from developing and will also help to prevent any more damage.

Troubleshooting Checklist for an Electric Water Heater

Electric water heaters have a similar appearance to their gas-fueled counterparts. In order to limit heat loss from the heated water, they both employ an insulated steel storage tank jacket, with insulation between the storage tank and the tank jacket. The primary difference between electric and gas water heaters is the source of heat used to heat the water. Electric upper and lower heating components that extend into the water tank heat the water in an electric water heater, which is powered by electricity.

When it comes to electric water heaters that provide little or no heat, the most common problem is a faulty heating element, which is a pretty affordable component that is quite simple to repair.

Watch Now: How to Repair an Electric Water Heater

Limited warranties are provided with both residential and commercial hot water heaters. Every tank is equipped with a rating plate that displays the tank’s model and serial number. These numbers specify the year in which the tank was manufactured, and they will decide if the tank is covered by a prorated warranty, which may include the provision of a new tank or replacement parts at no cost or at a discount.

Take a picture or write down the information, then contact the manufacturer if the tank is leaking or the element is not working correctly. Field labor is not covered by the manufacturer’s warranty. The following is something that you can perform before you start diagnosing the issue.

Warning

Working with electric water heaters when the power is on is risky since they are high-voltage (240-volt) equipment that can cause electrocution. Turn off the electricity to the water heater’s circuit by turning off the relevant breaker in your home’s service panel before inspecting any electrical components of the water heater (breaker box). Also, use a non-contact voltage tester to check all of the wires in the water heater to ensure that the power is turned off before touching any of the wires.

How to Fix

The Spruce Tree

No Hot Water

A water heater that does not generate hot water might be due to a lack of electricity, a tripped limit switch, or one or more faulty heating components, to name a few possibilities. As a first step, make sure that the circuit breaker for your water heater is not tripped on your panel of electrical circuit breakers. Switch off the circuit breaker and then turn it back on if it has been tripped. If the heater’s breaker does not trip (i.e., if it is still turned on), attempt the following steps to reset the high-temperature limit:

  1. Turn off the circuit breaker for the water heater’s circuit at the service panel if necessary. Removing the access panel for the water heater’s upper heating element is a good idea. Carefully remove all of the insulation and the plastic safety shield, taking care not to come into contact with any of the wires or electrical connections
  2. To reset the high-temperature cutoff, press the red button above the higher thermostat, which is positioned above the upper thermostat. Reinstall the safety guard, the insulating material, and the access panel. Turn on the circuit breaker for the heater. Test each heating element and replace it if required if this does not resolve the problem

“The Spruce” is a song by Candace Madonna.

Inadequate Hot Water

If your water heater is producing hot water but not enough of it, it is possible that your unit is too small to satisfy the hot water demands of your home. Take precautions to ensure that the water heater’s capacity does not exceed the demand.

How to Fix

In the case when your water heater is producing hot water, but not enough of it, it is possible that your unit is too small to satisfy the hot water demands of your home. Take precautions to ensure that the water heater’s capacity does not exceed its demand.

Water Temperature Is Too Hot

When there is too much hot water, it may be almost as annoying as when there is not enough hot water. If you’re encountering this problem, it’s possible that one or both of the thermostats on your water heater are set too high.

How to Fix

To double-check the thermostat settings, do the following:

  1. In the service panel, turn off the electricity to the water heater to conserve energy. The access panel, insulation, and plastic safety shield from each heating element on the water heater should be removed before continuing. Do not come into contact with any wires or electrical terminals. Using a non-contact voltage tester, check the cables to ensure that the power has been turned off. Ensure that the heat is set correctly on both thermostats: Both of them should be at the same temperature as each other. 115 to 125 degrees Fahrenheit is the acceptable temperature range. Make use of a flathead screwdriver to adjust the temperature to the correct level
  2. And Set the other thermostat to the same temperature as the first
  3. For each element, replace the safety guard, insulation, and access panel as needed. Turn on the circuit breaker for the heater.

“The Spruce” is a song by Candace Madonna.

Water Leaks

Water leaks are often caused by leaking valves and plumbing connections, but they can also be caused by difficulties with the tank’s drainage system. Water leaks may cause substantial damage to a property, which is why it is critical to repair the leak as soon as it is discovered.

How to Fix

Leaks from water heater tanks can occur as a result of faulty heating components or corrosion in the tank. Inspect the elements for looseness and, if required, tighten them with an element wrench to prevent them from moving. A rusted tank is unable to be repaired and must be completely replaced instead. Turn off the water heater’s power and water supply, and then totally drain the tank to stop the leaks from occurring. “The Spruce” is a song by Candace Madonna.

Rust-Colored Water or Bad Odor

If your water has a brown, yellow, or red tinge to it as it comes out of the faucet, corrosion might be occuring within your water heater tank or in the pipes in your home. If your water comes out smelling like rotten eggs, it’s possible that bacteria has built up in the tank of your hot water heater.

A professional plumber may be required to replace the anode rod in the tank, which is something that you should avoid doing unless absolutely necessary. courtesy of KariHoglund / Getty Images

Tank Making Noises

Is your water heater making noises? If so, what are they? Is there a low rumbling or popping sound when you turn it on? What if it’s a high-pitched whine instead? It’s possible that the sounds you’re hearing is the sound of boiling water. When there is a significant amount of sediment building in the bottom of a tank, it can cause the bottom of the tank to overheat, which can result in the water boiling.

How to Fix

In order to remove the silt from the tank, the first thing to attempt is to empty it. The tank may need to be replaced if this does not alleviate the problem. “The Spruce” is a song by Candace Madonna.

Leave a Reply

Your email address will not be published.