How To Relight Pilot Light On Water Heater

How To Relight the Pilot Light in Your Gas Hot Water Heater

When the hotwater heater in your home fails, duties such as showering, doing laundry, cleaning dishes, and other household chores come to a grinding halt. If you have a gas-powered hot water heater, it is possible that the pilot light has gone out, which is the root cause of the problem. In most circumstances, if you relight the pilot, you should be able to go back into the air again. In this post, we’ll demonstrate how simple it is to complete the task yourself.

What does the pilot light do?

The pilot light of your gas hot water heater is a tiny, continuously burning flame that serves to start the burner of the appliance. To put it another way, if the pilot light goes out, the unit will be unable to heat water. It is possible for a pilot light to be extinguished for a variety of causes, including something as simple as a short stoppage in the gas line or an air bubble in the gas line. Warning: If you smell gas at any stage throughout the process, leave the area immediately and contact your energy supplier as soon as possible.

Steps to relight the pilot light.

  1. Remove your foot from the gas pedal. Find the gas shut-off valve on your hot water heater and turn it off. The knob should be labeled in a clear and understandable manner. Turn the switch to the “Off” position and wait 5-10 minutes to ensure that all of the gas has been expelled. Locate the pilot light access point. Most of the time, this will be under the gas valve. To locate the burner and two gas tubes, open the pilot cover (if one is present) and use a flashlight to peer inside the hole to locate the burner and two gas tubes
  2. Return to the gas valve and turn the knob to the “Pilot” position. By depressing the knob all the way down, you will begin to feed gas to the pilot. There are certain hot water heaters that include a separate pilot button
  3. If this is the case, press that instead. While maintaining control of the knob or button, reach into the access and ignite the pilot with an extended lighter while still keeping it down. Once the pilot light comes on, keep the knob/button down for about one minute. Release the knob/button carefully after that period of time, and make sure that there is still a flame emanating from the pilot. Return to the gas valve and turn the knob to the “On” position. Typically, a noise will be heard to indicate that the primary burner is lighting
  4. After giving the heater enough time to restart, replace the access cover and inspect the hot water supply.

What happens if the pilot light goes out again?

The fact that the pilot won’t light or that it keeps going out is a clue that you may be experiencing another problem with your hot water heating system. The most typical issue we encounter is a thermocouple that is twisted, fractured, or filthy (also called a flame sensor). Because the typical service life of a hot water heater is 12-15 years, it may be a wiser investment in some situations to replace the unit rather than spend money fixing your existing unit. if your water heater isn’t producing enough heat, call Reidelt Plumbing Inc.

Our professional plumbers will come out to your home, assess the situation, and provide recommendations on how to restore hot water flow in your home.

  • This entry was published on April 30, 2020, under the category Water Heaters.

How to Relight the Pilot Light on Your Water Heater

Several factors might contribute to a pilot light on a water heater being turned off. The front of most water heaters will contain instructions on how to relight the pilot light, and this will usually be on the right side of the water heater. The first step is to turn off the gas to your water heater by turning off the gas control valve on the tank. Then follow these instructions to re-ignite the pilot light on your water heating system:

  1. Remove the access panel for the water heater
  2. Check to see if the gas valve is open (on most valves, this indicates that the valve is in line with the pipe)
  3. And Make sure that the gas control valve on the water heater is in the pilot position. Hold the knob on the front in and press it in. For a flame to emerge on the screen, hold down the ignitor button (the black square button below the knob). Keeping the knob pressed in until the indicator light starts blinking is recommended. Using the knob, adjust the temperature to your liking.

The flame should be visible via the viewing window if you look closely enough. That indicates that your pilot light has been turned on. Although the gas control valve on your water heater may be different, the process of relighting it should be very similar. You may look up “How to relight a _” on Google and fill in the blank with the name of the brand of your water heater to see what comes up. YouTube is another excellent source of information. Gas control valves come in a variety of shapes and sizes, and they might be installed on your water heater.

If you are unable to relight your pilot light, or if it does light but continues going out on you suddenly, contact a plumber you can trust for assistance in determining what is causing the problem.

The 25th of August in the year 2021 All of the posts

How to Light a Water Heater Pilot Light

Prev PostNext PostWhen the pilot light on a water heater goes out, it is typically because of a natural fluctuation in gas pressure, which extinguished the flame. The most obvious indicator that a pilot light has gone out is the one that everyone dreads: the water will not heat up properly. In the event of a damaged flame sensor, it’s critical to know how to relight the pilot light on your water heater so you can get the flame going as quickly as possible. This will not only allow you to get your hot showers back, but it will also ensure that no gas is unintentionally discharged into the home.

However, for the vast majority of gas-powered water heaters, you should begin by locating the gas shut-off valve on the water heater, which is generally plainly labeled on the front lower section of the water heater, before proceeding.

  1. Open the door or cover that provides access to the pilot light. In most cases, this will be positioned under the gas valve
  2. However, some water heaters will just have an open gap where you can see the pilot light burner instead. Locate the burner within the container using a flashlight or a headlamp. It will be reached by two little gas tubes. You’ll want to keep an eye on it while you’re at work. Turn the gas knob to the “Pilot” position and push and hold the button. This will initiate the flow of gas, allowing you to ignite the flame. Some water heaters feature a separate pilot mode button, which is commonly a red button, which you must push and hold in order to activate it. While keeping the gas pedal depressed, ignite the pilot light. Certain water heaters feature an igniting button that is red or black, while others must be lighted manually with a long lighter
  3. Some models include a red or black igniting button. Maintaining pressure on the gas knob or button for a full minute after the flame is ignited is critical. Then slowly release it while checking to see if the light is still on. Turn the gas knob to the “On” position and listen for the unmistakable “whump” or whooshing sounds that indicates the main burner has ignited. Enjoy your hot shower when you’ve replaced the lid.

Despite the fact that a single extinguished pilot light is normally caused by a natural fluctuation in gas pressure, recurrent faults suggest a more serious problem with the water heater itself. The most typical problem that causes repeated pilot outages is a filthy or bent thermocouple, which is a thin copper wire and rod that detects the presence of a flame and immediately switches the gas off when it detects a lack of flame detection.

What is a Thermocouple?

A thermocouple is sometimes referred to as a flame sensor in contemporary water heaters because of the way it detects flames. Your thermocouple is most likely twisted, filthy, or damaged if the pilot light continues to go out after you have completed the above-mentioned lighting procedures. For those who find that their pilot light is twisted and not near the burner, they may simply turn off the gas, shift it over, and attempt lighting the pilot again. It may be necessary to clean the water heater gas valve and the main gas line near the heater if this does not solve the problem.

  1. The burner is typically simple to remove by simply sliding it out.
  2. If this doesn’t solve the problem, you may get a new thermocouple for less than $15 at any hardware store or home improvement center.
  3. Rooter Plumbing to help you get hot water back into your home again.
  4. The use of hot water is simply one component of a great showering experience.
  5. Previous PostNext Post Previous Post

How to Light the Pilot for a Gas Hot Water Heater

When the water in the tank needs to be heated, tank-type gas water heaters utilize a pilot light to ignite the gas burner, which then heats the water. The cold water flowing from the hot water tap is usually the first sign that your pilot light has gone out, so keep an eye out for it. Even if the equipment is not malfunctioning, a pilot light might go out for a variety of causes, including sudden swings in gas main pressure. If the pilot light on your heater goes out, you may relight it by yourself.

1.

  • Find the gas regulator valve on the water heater and turn it on. It is positioned on the exterior of the water heater, near where the gas line enters the device, and it is controlled by a knob on the outside. The gas supply to the pilot burner beneath the hot water tank is controlled by this valve. To turn the valve off, turn the knob all the way to the left. Wait five minutes before continuing. Locate the pilot burner, which is located beneath the natural gas water heater. Remove or unsnap any access cover that is preventing you from getting to the burner. Make use of the flashlight to illuminate the pilot burner

2.

  • Turn the knob on the gas regulator valve to “Pilot,” press down on it, and keep it pressed down. The flow of gas to the pilot burner is initiated by pressing this button. To start the pilot burner gas flow on some water heater types, you must push and hold down a separate red button for a period of time. Find a red or black button labeled “Ignition” on the top or side of the gas valve if your heater has a piezoelectric spark pilot igniter built in. To start the pilot, press the button on the control panel. As the igniter ignites, you will hear a click sound. If you must manually ignite your heater, a long-necked barbeque lighter is the most secure type of lighter to use. Light the pilot burner with a lighter flame and turn it on.

3.

After the pilot has been ignited, keep the regulator valve knob firmly depressed for at least one minute. This permits the pilot flame to heat the thermocouple safety sensor, which detects the presence of a live pilot flame, allowing the pilot flame to heat the sensor. Reduce the pressure on the regulator valve knob gradually. When the pilot light continues to glow after you have released the knob, turn the knob to the “On” position. During the ignition of the primary burner, you should hear a muffled “whoomp” sound.

Things You Will Need

Look for a label on your gas water heater that provides particular pilot lighting instructions for the model of water heater you have installed.

Warning

  1. Look for a label on your gas water heater that provides precise pilot lighting instructions for the model of water heater you have.

How to Relight Your Water Heater Pilot Light (For Every Major Brand!)

The pilot light on your hot water heater has great influence on your life. Anyone who has walked into their shower on a frigid winter morning, with their body freezing and their teeth chattering as they wait for hot water that never arrives, knows what I’m talking about. In the case of a natural gas water heater, this might indicate one of two problems. There are two possibilities: either (1) the gas supply has been switched off or (2) your pilot light has gone out. We should first address the likelihood that your gas supply has been interrupted (and as fast as possible).

1. How to Make Sure Your Gas Supply is On

  1. Locate the shut-off valve for your natural gas line
  2. It is common to find the shut-off valve near to your gas meter (as shown in the figure below), which is often positioned on the side or front of your home or major structure. Check to be that the shut-off valve attached to your gas line is in the “ON” position before proceeding. If it is not in the ON position, the problem is not with your gas line
  3. However, if it is, the problem is with your gas line. If the valve is currently in the OFF position, switch it to the ON position. Please do not hesitate to contact your local gas company for assistance.

Examining your gas line is the first step in determining whether or not you have a lack of hot water. Double-check to see that the gas shut-off valve is in the “ON” position. If everything is in working order with your gas supply, it’s time to check the pilot light on your water heater.

2. How to Light Your Pilot Light Water Heater

Depending on the manufacturer, re-igniting a pilot light may need a different procedure. Fortunately, there are just a few number of producers. The first step should be to check for the installation instructions, which are normally fastened to the water heater. Don’t be concerned if you can’t locate them. Specific brand-by-brand instructions are provided in the section below. Instructions in this video are “generalized,” as the title indicates. Scroll down to the bottom of this page for instructions unique to your brand of water heater.

How to Light a Rheem Hot Water Heater Pilot Light

The pilot light on an ARheem water heater must be manually activated by striking thepiezo ignitor striker that is incorporated within the water heater.

  1. Using a clockwise motion, turn the gas knob on your Rheem water heater until it is at the desired position
  2. Counter-clockwise turn the temperature dial on the water heater until it is set to the lowest temperature setting. Wait five minutes to let any gas in the water to pass through
  3. Remove the outer door of your Rheem water heater from its mounting bracket. Counter-clockwise turn the gas knob to the “Pilot Light” setting until it is in this position. Press the red button to the left of the gas knob until it becomes depressed. The piezo ignitor striker is located on the left side of the gas knob. While maintaining pressure on the red button, continually push the piezo ignitor striker until the pilot light is re-lit until the problem is resolved. Through the viewing glass on the inside of the Rheem water heater’s inner door, you can see the pilot light. After the pilot light has been turned on, continue to hold down the red button for one minute before releasing it completely. The pilot light will remain on during the process. Remove and reattach the outer door of your water heater
  4. To turn on the gas, turn the knob to the “ON” position. Set the hot water temperature slider to the temperature that you desire for your water

How to Light an A.O. Smith or State Water Heater Pilot Light

AO Smith water heaters andState water heaters, including the Conservationist model, are equipped with a piezoelectric igniter mechanism that lets you to light the pilot by pressing the ignition button on the water heater.

  1. Disconnect the access panel from the side of the A.O. Smith or State water heater and place it somewhere out of the way
  2. To turn off the gas supply, turn the control knob on the water heater’s side to the “OFF” position and let the room air out for roughly 10 minutes. The “Pilot Light” setting on the gas control knob should be selected. The red button should be pressed down (this will allow the gas to flow to the burner assembly)
  3. And While maintaining pressure on the red button, press down on the ignitor button until the pilot light illuminates. It is possible that you may have to press down on the ignitor button two or three times before the hot water heater pilot light turns back on. Continue to hold down the red button for approximately 60 seconds after the pilot is lighted, then gently release the button. Make sure the gas is turned on by turning the control knob to “ON.” Replacing the access panel on the side of the water heater is necessary.

How to Light a Bradford White Water Heater Pilot Light

  1. Disconnect the access panel from the side of the A.O. Smith or State water heater and place it somewhere out of the way. To turn off the gas supply, turn the control knob on the water heater’s side to the “OFF” position and allow the room to cool for roughly 10 minutes. The “Pilot Light” setting on the gas control knob is selected. Continue to press down on the red button, allowing for a steady supply of gas to reach the burner assembly. In the meantime, keep holding down the red button and pressing down on the ignitor button until the pilot light illuminates. Before the hot water heater pilot light turns back on, you may need to press down on the ignitor button two or three times. After the pilot is lighted, hold the red button down for approximately 60 seconds before carefully releasing the button. Set the gas control knob to the “ON” position
  2. Turn on the gas. Reinstall the access panel on the side of the water heater
  3. And
See also:  How Much Is A 50 Gallon Water Heater

Resources

  • Precautions to take when using a water heater
  • How to get hot water back from your water heater
  • The components of a water heater
  • Water heater maintenance and repairs
  • What is the average lifespan of a water heater?

Call 1-Tom-Plumber

It might be rather frightening to experiment with the gas in your house. Don’t be concerned, we’ll have you back in a warm shower in no time!

Please do not hesitate to contact us or call 1-Tom-Plumber (1-866-758-6237). Regardless of the nature of the emergency plumbing, drainage cleaning and drain clearing, or water damage situation, we will respond quickly. This includes excavation of subterranean water pipes and sewage main lines.

How to Light a Water Heater

Documentation Download Documentation Download Documentation You may see cold water flowing from your hot water faucet if you reside in a home that has a natural gas water heater. This is a good indication that your pilot light has gone out. It is not necessary to hire a professional in most circumstances; you will have hot water again in a matter of hours if the pilot is re-ignited correctly. While having your water heater’s instruction manual on hand is a good idea, it is not fully required because most gas water heaters need a similar process for relighting the pilot light, as described in this article.

  1. 1 Make that the pilot light is working properly. You will most likely need to remove a tiny panel at the bottom of the tank, known as an access panel, in order to determine whether or not the pilot light is truly turned off. If you do not see a little flame flickering, this indicates that your pilot light has failed.
  • Depending on your water heater model, it is conceivable that your panel is not detachable and that you must observe your pilot light via a transparent window. It is possible that your pilot light has gone out if you are unable to see a flame burning through the glass in this situation.
  • 2 Check to see whether there is any gas leaking. Never attempt to restart your pilot light if there is gas leaking from your water heater, as this is highly harmful to both you and your property. Instead, call 911 immediately. If there is any evidence of leaking, perform a basic smell test before trying to ignite the pilot again.
  • Second, check for any signs of gas leakage. If there is gas escaping from your water heater, you should never attempt to re-ignite the pilot since this is highly harmful to both you and your house. Test the pilot for leaking using a basic smell test before attempting to restart it.
  1. Advertisement
  2. s3 Instructions may be found on the inside of the door panel of your water heater. Detailed instructions for your specific water heater model may be available here, and following them may assist you in the process of relighting the pilot for your unique water heater. Advertisement
  1. Step 1: Lower the temperature control setting to the lowest possible setting. 2Find the regulator valve, which is normally situated on the front of a box on the outside of the water heater
  2. 3Find the pressure relief valve. In most cases, this valve is positioned on the same box as the temperature control, but it is more likely to be on top of the box
  3. It regulates gas flow to the pilot burner beneath the hot water tank. To turn the knob off, turn it to the “Off” position. Wait 10 minutes after turning off the knob before proceeding to ensure that any remaining gas from the tank has cleared the air before continuing. The importance of safety cannot be overstated. 4 Determine the type of water heater that you have installed. Gas hot water heaters are often classified into two categories: “new” and “ancient.” Traditional heaters will require you to relight the pilot with your own flame, however newer design tanks are fitted with a pilot light igniter built in into the tank.
  • However, while the specific appearance of the buttons on modern design tanks may vary, many of them include a red igniter button that is located a few inches away from the temperature and regulator valves.
  • 5 Gather any lighting items that may be required. The pilot light on an old-style water heater must be re-lit with a “wand” lighter or fireplace matches since the pilot is too lengthy to reach with a standard lighter.
  • Gather any lighting items that could be required. If you have an old-fashioned water heater, you will need to obtain a long-reach “wand” lighter or fireplace matches in order to relight the pilot light.
  1. 6Travel to the location of the pilot. The pilot is positioned at the end of the little silver tube that comes out of the control valve and is connected to the control valve. It’s possible that you’ll need to use a flashlight to see clearly in this location. Advertisement
  1. First, put the gas valve to the “Pilot” position by pressing down on it with your finger. Starting the flow of gas into the tube that provides the pilot light is accomplished in this manner.
  • Find a red control button near the gas valve on your water heater if the gas valve on your water heater does not press down properly. Hold this button down for a moment.
  • 2 Light the pilot burner with a match. The pilot gas valve or the red button will be held down with one hand while the other hand will be used to swiftly light the pilot.
  • To use this button, make sure you have a new model water tank with a built-in ignition switch installed. You should be able to hear a clicking sound until the pilot burner comes on. If you have an old-fashioned heater, ignite the pilot burner with a wand lighter or match and wait a few minutes. Because you will be using one hand to push the valve/red button while using the other hand to ignite the pilot, you may require the assistance of another person to carry a flashlight for you if you require additional lighting. Make an effort to get assistance in advance so that you do not go halfway through a procedure only to be forced to halt because you are unable to see what you are doing
  1. 1 Minute after the pilot light has been ignited, keep the gas valve or control button down by pressing it down one more time. In this case, the thermocouple will be heated, which is a sensor that turns off the gas when the pilot is not lit. 4Remove the valve knob/control button from the valve. Check to check if the pilot light is still illuminated after a minute by releasing the valve and pressing the control button. 5Replace the access panels with new ones. When checking to see if the pilot light is still glowing, replace the access panel (if you had to remove it first) to ensure that no flames are escaping into your home. 6Re-ignite the main burner if necessary. Turn the main gas valve back to the “On” position and set the temperature control to the appropriate temperature. The main burner under the tank should be turned on and the water in the tank should begin to heat. When turning the knob to “on,” take care to keep your head away from the burner area. 7Set the thermostat to the temperature you wish. Remember not to heat the water to a boiling point, since you might scald your hands or body accidently when washing or bathing. The Consumer Product Safety Commission recommends a temperature of 49 degrees Celsius (120 degrees Fahrenheit). Advertisement

Create a new question

  • QuestionHow can I start a newer model gas heater that is on the market? Look up your model number and get in touch with the manufacturer for more detailed information. As a general rule, the most significant difference between a modern heater and these instructions is that newer types feature an electronic igniter (you simply press the button and a spark is produced) for lighting the pilot. Question What do I name the gadget that I use to ignite the pilot’s engine when I press a button on it? You refer to it as a “spark igniter.” Question What should I do if the pilot light on my water heater keeps flickering on and off? It is likely that you will have to replace it. Make contact with a supplier or even the firm that produced your water heater for further information. Question What should I do if the pilot light won’t remain lit for whatever reason? The most likely cause of your problem is that your thermocouple has to be repaired or replaced. A pilot light is a short copper tube that connects your water heater’s controls to the pilot light and has an end that sticks into the flame. Whenever the pilot light heats up the tip, it creates electricity that is detected by the control box, which allows it to determine that the pilot light is on. A new one is simple to install, and you can pick one up at any home improvement, plumbing supply, or hardware shop. Take your old one with you so that you may acquire the right measurement. A little bit longer is OK, but not typically much shorter
  • Question When I press the pilot button, how long should I hold it down before pressing the little red ignitor button beneath it? It takes around 5 seconds. Restart it and make any necessary adjustments to the temperature. Question So, what should I do if the pilot light won’t turn on for whatever reason? Continue to try while keeping an eye out for any signs that there is gas coming through (usually by smell). The likelihood is that the regulator is faulty and that it will need to be replaced. This is also something that you can accomplish on your own.

Inquire about something There are 200 characters remaining. Include your email address so that you may be notified when this question has been resolved. SubmitAdvertisement

Video

  • If this procedure does not provide results, check to see that the pilot light’s base is not filthy or blocked. If it is, clean it well and repeat the process after 10-15 minutes. You may also try holding the valve/control button for an additional 30-45 seconds after the pilot light has been ignited. If this technique does not work, it might be due to a lack of gas pressure or a defective gas valve. If you are unable to light the water heater after many efforts, contact an appliance repair person, a plumber, or your gas provider. You may have a faulty thermocouple if the pilot light does not come back on after being re-lit or if it goes out soon after being re-lit. It is possible to see the thermocouple in the pilot light flame region because it extends from the temperature control into the flame area. The cost of one is pretty low, and you can do it yourself.

Thank you for submitting a suggestion for consideration! Advertisement

  • If you detect the scent of gas anywhere in your home, contact your gas provider right once. Even a “little quantity of gas” is too much
  • Do not re-open the gas valve until you have completed the replacement of the access panels and doors. It is possible that a flame will come out of the water heater if this is done.

Advertisement

About This Article

Summary of the Article Set the temperature control to the lowest setting and turn the gas regulator valve to the “Off” position to begin lighting an electric water heater. X Then, by adjusting the gas valve to the “Pilot” position and pressing down on it, you may begin to pump gas into the system. After that, press the red ignitor button, which is located near the gas valve, to ignite the pilot burner. Hold down the pilot button for 1 minute longer than you think it should be and check to see whether the pilot is lit.

Continue reading for helpful hints on how to prepare for and light your water heater.

The writers of this page have together authored a page that has been read 388,656 times.

Did this article help you?

The date is May 13, 2021. When the pilot light flame on your gas water heater goes out, it is an annoying and frustrating situation to have to deal with. When your water heater’s pilot light fails to stay lit, you’re left without hot water, which makes even the most basic of tasks such as taking a shower a chore. Naturally, you question, “How did this happen? What happened?” Is there anything you can recommend to help you get things going again? What should I do to have it repaired? “May you tell me about the costs I can expect?” Fortunately, if your water heater pilot light goes out, you should be aware that this is a frequent problem that many homeowners have and that the time and effort required to repair it is low.

Why does the pilot light on my water heater keep going out?

Because of problems with the heater’s thermocouple or owing to access to combustible air, your water heater’s pilot light continues going out repeatedly.

Thermocouple Issues

When your pilot light is on, your thermocouple detects the presence of the flame. The thermocouple’s tip is positioned above the pilot flame, providing a voltage that maintains the gas valve open in the process. A thermocouple will shut down the gas supply to your water heater if it detects that the pilot light on your water heater is not lighting up properly.

When thermocouples are exposed to moisture or dust for an extended period of time, they might malfunction, gather dust, or get bent away from the pilot light’s flame. In either situation, the thermocouple will have a difficult time sensing the pilot light and shutting down the gas flow.

Lack of Combustible Air

Another reason why your gas water heaterpilot light won’t remain lighted might be that there isn’t enough combustible air in the room where it is located. To keep the pilot light on in your water heater, you’ll need to blow air into it. Otherwise, the flame will be extinguished. Take precautionary measures to ensure that the water heater is not surrounded by material, such as litter or lint, which might increase the quantity of combustible air present. Maintain as much cleanliness as possible in the surrounding region.

What do I do if my water heater pilot light keeps going out?

Try to rekindle the spark on your own first, if at all possible. Take the following general steps:

  1. Try to rekindle the flame on your own first to see if it works. Generally speaking, you should:

If you are unable to relight the pilot or if your pilot light keeps going out, it is possible that you have another problem, such as a faulty thermocouple, to consider. Please refer to the owner’s handbook for your water heater equipment for further information.

Can I replace a thermocouple myself?

Yes. In the event that you are handy with tools, you may be able to change the thermocouple yourself. It is easier to accomplish this by turning off the gas valve and removing the entire burner and thermocouple assembly. In the case of minor repairs, it is preferable and safer to hire someone who is knowledgeable in the field of repair. A specialist may also evaluate your water heater for other faults and provide advise or ideas on how to deal with any existing or future difficulties that may arise.

Call BGE HOME

Please contact BGE HOME at (410) 918-5600 if your water heater pilot light will not light or continues going out. You may also contact us online. Our licensed specialists are available 24 hours a day, seven days a week to come out and inspect your water heater and make recommendations on how to get it running safely and effectively again. This item was posted on Thursday, May 13th, 2021 at 4:09 pm and is filed under Uncategorized. Commenting and pinging are temporarily closed for this post.

How to Relight Your Water Heater’s Pilot Light

An Overview of How to Turn on a Water Heater Pilot Light

  • Step 1: Turn off the gas
  • Step 2: Put the controls in “pilot mode.” Step 3: Press the control button and the light button simultaneously. Step 4: Bring the water temperature back to normal. Step 5: Reinstall the lid.

Don’t freak out if you find yourself without hot water for no apparent reason. It’s possible that the pilot light on your gas water heater has gone out. Despite the fact that this little blue flame should always be burning, it can go out for a variety of reasons. The good news is that, in the majority of situations, relighting is a simple process. This Might Also Be of Interest to You: Using These 5 Simple Steps, You Can Relight Your Furnace Pilot Light Please see the following steps for relighting the pilot light on your gas water heater.

See also:  What Causes A Water Pump To Fail?

How Do I Know If My Pilot Light Is Out?

Never panic if you find yourself without hot water at an inconvenient time. It is possible that the pilot light on your gas water heater has failed. Despite the fact that this little blue flame should always be burning, it might go out for a number of reasons. In most situations, relighting is a simple matter of repositioning the wick and readjusting the flame.

Additionally, you may be interested in the following information: How to Relight the Pilot Light on Your Furnace in 5 Easy Steps. Please see the following instructions for relighting the pilot light on a gas water heater.

Can I Relight the Pilot Light by Myself?

In many circumstances, you will be able to relight the pilot light on your water heater by yourself. First, check sure there isn’t a gas leak in the area where you’re trying to relight the pilot light. Usually, a simple whiff will suffice to do this. Natural gas is usually scented by the utility companies in order to make it easier to discover leaks in your house. Most of the time, the scent is comparable to that of garlic or rotten eggs. If you suspect that you are smelling gas, do not attempt to relight the pilot light.

For further information, contact your natural gas utility.

Gas hissing and blowing noises may also signal the presence of a gas leak.

Additional Related Articles:

  • The pilot light on your water heater is often easy to relight on your own. Check to see if there is a gas leak before attempting to relight the pilot light. In most cases, a simple whiff will be sufficient. In order to make it easier to identify a leak in your house, most utility providers smell natural gas. When it comes to scent, it’s usually comparable to that of garlic or rotten eggs. Avoid relighting the pilot light if you suspect you are inhaling gas. The alternative is for everyone in the family to evacuate the premises immediately. For further information, contact your gas company. If you hear any weird noises near your water heater, you should investigate these as well. Soundings such as hissing and blowing may also signal a natural gas leak. As long as none of these warning indicators are present, you should be safe in your attempt to relight your pilot light on your own to ensure proper operation. Articles that are related:

What Do You Do When the Pilot Light Goes Out?

Re-lighting the pilot light according to the manufacturer’s instructions for your equipment should be attempted if at all possible. The procedure, on the other hand, is very consistent across different kinds of gas water heaters. To begin, establish if your water heater is equipped with an automated or manual ignition system. A glimpse at the control dial should be enough to notify you, according to Mullen Plumbing, Heating, and Cooling of West Virginia. If you have an automated igniter, it is likely that you have an ignition button.

It will be necessary to manually relight your pilot light.

How to Light a Pilot Light on a Water Heater Without an Automatic Igniter

  1. Using the access cover, switch the gas control valve to the “off” position to cut off the gas supply. Allow about 10 minutes for any gas that has gathered to disperse. The “pilot” position is reached by turning both the control and the water temperature knobs. To activate the control knob, depress it. To re-ignite the pilot light, hold the button down while using a wand lighter or long match to ignite it. A continuous flame should be visible once the pilot light has been turned on. For a full minute, continue to keep the knob down to force air out of the line that has accumulated over the course of time. Turn the knob to the left
  2. Set the temperature of your water heater back to the appropriate level by turning the control knob. Remove the access cover and replace it.

How to Light a Pilot Light on a Water Heater With an Automatic Igniter

  1. Remove the access cover from the door. To turn off the gas, turn the gas control valve to its “off” position. Wait about 10 minutes for the gas to disperse before continuing. Then, set the control and water temperature knobs to the “pilot mode.” To use the control button, press it. While maintaining pressure on the trigger, continually push the striker knob for approximately 90 seconds, or until the pilot is lighted. The striker knob is usually either black or red in color. Continue to hold down the control knob for a full minute to bleed air from the line, then release it.
  2. Set the temperature of your water heater by turning the control knob to the appropriate setting
  3. Replace the access cover in a safe manner.

Your pilot light should remain bright if it was accidentally turned off due to a draft or similar one-time problem. If it doesn’t work the first time, wait 10 minutes before attempting to ignite it yourself again after that. Having trouble with your water heater’s pilot light? It’s possible that your device requires expert maintenance or repair. Because we are spending more time at home than ever before, it is critical to be prepared for unexpected home repairs with a plan from HomeServe. The knowledge that you can easily call our 24-hour repair hotline in the event of a covered breakdown provides you more peace of mind.

Step by Step Guide: How to Light a Water Heater

Get your hot water heater up and operating in a safe and efficient manner. Get quotations from as many as three professionals! Enter your zip code below to get matched with top-rated professionals in your area. You should examine your hot water heater first if your hot shower has turned into freezing rain after you have turned on the hot water. Homes using gas water heaters should check their pilot lights to be sure they haven’t been turned off accidentally. The age of your heater may determine whether or not you may use an ignition button or a lighter to relight the pilot light on it.

The following tools and materials will be required:

How to Relight a Gas Water Heater’s Pilot Light

To relight a hot water heater, just follow the instructions outlined in the following section.

1. Safety First

Even though the vast majority of homeowners are capable of relighting a pilot light on their own, it’s crucial to use caution when working with a gas-powered hot water heater. When relighting a pilot light, you should always proceed with caution since the gas used to power your hot water heater is volatile and possibly deadly. If you smell gas at any time, you should turn off the gas valve immediately and open the windows to let the gas escape. Do not switch on any lights. Leave your home and call the gas company or the fire department for assistance.

2. Turn Off the Gas

First and foremost, you must switch off the gas supply before re-igniting the pilot light. Locate the gas valve on your hot water heater and turn it to the “off” position to turn the water off. Hold off for around 10 minutes; this will give any gas in the region time to clear, which is vital because the gas is very combustible, so patience is required.

3. Access the Pilot Light

It is customary for the pilot light to be situated directly beneath the gas valve. In certain circumstances, a door or cover may be placed over the light to prevent it from being seen. While you are doing this procedure, use a flashlight to ensure that you can see everything clearly and accurately.

4. Turn the Gas Valve to ‘Pilot’

Turn the gas valve to the “pilot” position and push the button. As a result, the gas valve provides enough gas to ignite the pilot light, which is what you want. If your hot water heater is equipped with a separate pilot button, this is something to look for.

5. Light the Pilot

The method you use to relight the pilot on your gas water heater is determined on the age of the appliance. Gas water heaters manufactured during the last eight years are not required to include manual illumination. Instead, these water heaters are equipped with an electric spark generator, similar to that found in a gas grill. To ignite the pilot light on a water heater that has a pilot light ignition button, you should press the button until the pilot light illuminates. If your water heater does not have such a button, you’ll have to manually ignite it with a long lighter if it does not have one.

6. Turn On the Gas

Once the pilot light has been lighted, re-ignite the gas supply.

7. Don’t Be Afraid to Ask a Professional

If you want assistance, consult with a local water heater technician, particularly if your hot water heater requires manual ignition. Most service providers will charge a set price every visit, which will normally cover the cost of relighting a gas water heater in the event that one is required. The cost of this service call might range between $80 and $100.

FAQs About Hot Water Heaters

Photograph by Hmzalldesign/iStock / Getty Images Plus courtesy of Getty Images If your water is barely lukewarm, it is possible that your hot water heater is malfunctioning. It might be a sign that your water heater is going to malfunction, that sediment has accumulated, or that the temperature has been adjusted improperly. In order to establish the specific nature of the problem, you need consult with a water heater repair professional.

How much does it cost to repair a hot water heater?

The cost of repairing a hot water heater can range from$225 to $960 depending on the model.

The cost of repairing a water heater varies based on where you reside and what is wrong with it. In certain circumstances, it may be more cost effective to replace your hot water heater rather than repair it.

How do I maintain my water heater?

Some things you can do to keep your hot water heater in good working order include examining it on a regular basis and flushing it out of the tank.

How to Fix a Water Heater Pilot Light

Time Approximately one hour or less Complexity Cost for a beginner is less than $20.

Introduction

If your hot water heater suddenly stops operating, it’s likely that a faulty thermocouple has caused the gas to the pilot light to be turned off. Replacement is a simple do-it-yourself project.

Tools Required

Is there no hot water? If you have a natural gas or propane water heater, there is a good probability that the pilot light has gone out. It is this little flame that starts the gas burner on your water heater that is referred to as the pilot light. When the pilot light on your water heater goes out, the first thing you should do is try to relight it by following the instructions on the water heater label. The thermocouple is by far the most prevalent cause of pilot failure, whether it occurs immediately after lighting or on a regular basis after the pilot has been extinguished.

If you do not wait for a professional to arrive, you will be able to get your hot water running without incurring the expense of a service visit.

What is a Thermocouple?

  • In order for gas to flow to the burner, a thermocouple must be used to detect the heat of the pilot. A faulty thermocouple will prevent gas from reaching both the pilot and the burner, resulting in the pilot light failing to stay lit.

Project step-by-step (6)

  • Shut off the gas line by closing the cutoff valve. As seen in this photo, turn the valve a quarter turn so that the handle is at a right angle to the pipe.

Unscrew the Nuts

  • Make sure you turn off the gas cutoff valve. Check that you have turned the valve one-quarter turn so that the handle is at a straight angle to the pipe, as shown in the photo

Sign Up For Our Newsletter

Complete your do-it-yourself tasks like an expert! Become a subscriber to our newsletter! Do It Right the First Time, and Do It Yourself! Step number three.

Remove the Assembly

  • Remove the water heater pilot light burner component from the water heater. Remove the old thermocouple by unscrewing or pulling it out. Purchase a new one that is the same size and length as the previous one

Install the New Thermocouple

  • Install the new thermocouple in the same manner as the previous one
  • Replace the burner assembly by sliding it back in. Reattach the three wires to the control valve where they were disconnected.

Reattach the Lines to the Gas Valve

  • The three lines must be reconnected to the gas valve by threading the nuts into position with your fingers and hand-tightening them
  • A quarter- to half-turn of the wrench tightens them up.
  • Pro tip: Because the metals are delicate, avoid overtightening them.

Test for Gas Leaks

  • Keep in mind that in order to test for leaks, the pilot light must be lighted and the burner turned on so that gas flows through the big tube.
  • Replenish the water supply by opening the shutdown valve and lighting the pilot light. Turn the control valve to the “on” position. Use a 50/50 mixture of dish soap and water to check the screw joints for air bubbles, which indicate a leak, while the gas burner is turned on.
  • Replenish the water supply by opening the shutdown valve and lighting the pilot light
  • The control valve should be turned on. Testing for leaks in screw joints should be done when the gas burner is turned on with a 50/50 mixture of dish soap and water.

CAUTION!

Reopen the cutoff valve; relight the pilot light; re-start the engine Set the control valve to the “on” position. Use a 50/50 mixture of dish soap and water to check the screw joints for air bubbles that signal leaks when the gas burner is turned on.

WhenNotto Replace the Thermocouple

Some gas water heaters have a burner chamber that is “closed,” making it impossible to reach the burner. It is recommended that you contact a professional to repair this sort of heater. In addition, some gas water heaters are not equipped with pilot lights. Allow the professionals to take care of this as well.

Why Your Pilot Light Keeps Going Out & How To Fix [With Pictures]

That darn pilot light just won’t stay turned on! Moreover, it is causing all of your plans for today to be derailed. Nothing compares to the sensation of taking a hot water shower. However, there are times when this does not occur. After all, there are worse things than having a very cold bath, should we say? The one thing that everyone despises is a lack of running water. This may be incredibly inconvenient – not only for showering, but also for all of the other duties that require hot water to be completed successfully.

You don’t have to put your day on wait because your pilot light isn’t working properly.

However, if you discover that your water heater is leaking water and that this is the root of your water problem, read our guide on what to do when your water heater is leaking water! Repair Your Pilot Light Right Away With a Pro!

What’s A Pilot Light?

An electronic device that maintains a continually burning flame is known as a pilot light. Basically, the goal of this section is to light the burner. How? When you switch on your appliance, gas is released from the main burner, and the pilot light flame ignites the gas, so supplying heat to the room. With each degree of heat generated by the main burner, the air or water contained within your appliance is heated and then disseminated as needed around your residence or place of business

Appliances With Pilot Lights

An electronic device that maintains a constant flame is known as a pilot light. Essentially, the function of this section is to light the burner. How? When you switch on your appliance, gas is released from the main burner, and the pilot light flame ignites the gas, so generating heat. Because of the heat generated by the main burner, the air or water contained within your appliance is heated and then disseminated as needed around your house or office as well.

Water Heater Pilot Light: Where Is It And What Does It Do?

A little access panel, located just underneath the thermostat, may be found at the very bottom of your gas water heater. The pilot light for the gas water heater is located within the access panel. There will be a gas panel where you may check to see if the pilot flame has been ignited. The pilot light on your water heater is a little flame that is used to ignite the gas burner in the water heater. This is required for the purpose of heating the water that will be dispersed around your home. If you are experiencing no hot water and have attempted to relight your pilot light without success, you will require water heater repair.

Warning!

This photograph was shot by a water heater professional for the purpose of giving a demonstration on the use of pilot lights.

What Makes Your Water Heater Pilot LightGo Out

Thermocouple on the water heater is faulty. The thermocouple is responsible for detecting whether your pilot light is on. This copper rod serves as a safety precaution, preventing the heater’s gas supply from being turned off if the pilot light on the water heater goes out. The natural wear and tear of a thermocouple can cause it to get twisted out of place, to malfunction, to become broken, to become covered in dirt, or to accumulate carbon deposits. When one or more of these conditions occurs, the thermocouple will be unable to reliably detect the pilot light and will subsequently shut down the heating system.

See also:  How To Pump Water From Dehumidifier?

Strong Breeze Can Blow Out Pilot Light

On the water heater, there is a faulty thermocouple The thermocouple is responsible for detecting when your pilot light is on and when it is off. If the pilot light on your water heater burns out, this copper rod acts as a safety feature, cutting off the heater’s gas supply. A thermocouple can become twisted out of place, malfunction, become damaged, or become covered in dirt or a build-up of carbon as a result of normal wear and tear and environmental conditions.

In any of these cases, the thermocouple will be unable to reliably detect the pilot light and, as a result, the heating activity will be interrupted.

Kink in the Flex Tube

Thermocouple failure on the water heater The thermocouple is responsible for detecting when your pilot light is lit. This copper rod serves as a safety measure, preventing the heater’s gas supply from being turned off if the pilot light on the water heater fails. A thermocouple can become twisted out of place, malfunction, become damaged, or become covered in dirt or a buildup of carbon as a result of normal wear and use. In any of these cases, the thermocouple will be unable to reliably detect the pilot light and, as a result, the heating operation will be terminated.

Filthy Pilot Light OpeningCan MakePilot Light Keeps Going Out

If the pilot’s mouth is clogged with muck and debris, it will be virtually hard for it to maintain a flame. It will only keep a modest flame that will be readily extinguished if it does catch fire. Your pilot light will not stay lit if your pilot orifice is clogged with debris.

How Do I Re-Light My Gas Water Heater Pilot Light?

The pilot light on the water heater is not lighted.

Step 1: Thoroughly Read Gas Water Heater Manual

To have a better knowledge of where each component of your water heater is situated, consult your water heater’s instruction manual.

Step 2: Turn Down Thermostat

To have a better knowledge of where each component of your water heater is situated, consult your water heater handbook.

Step 3: Turn OFF Gas

The gas valve for the water heater Locate the gas shut-off valve and turn it all the way to the “Off” position. The gas shut off valve is positioned on the gas line near the base of your water heater, near the base of your water heater. Before proceeding on to the next stage, you must wait at least 5 minutes to guarantee that all of the gas has dissipated completely.

Step 4: After 5 Minutes, Turn The Gas Control Valve Setting On Water Heater To “Pilot”

The gas valve of a water heater. The gas shut-off valve should be located and turned “off.” Located near the base of your water heater on the gas pipe, the gas shut off valve is a safety feature. Before proceeding to the following step, you must wait at least 5 minutes to confirm that all of the gas has dissipated.

Step 5: HoldDownthe Reset Button

Keep the water heater reset button depressed. After that, press and hold the reset button. This is a button that is often red in color and is situated to the left of the gas control valve. Keep your finger on this button. To be on the safe side, use the instructions to identify each component.

Step 6: While Holding Down The Reset Button, Press TheIgniter

Keep the water heater’s igniter down. The igniter is located to the right of the gas control valve. While continuing to keep the reset button down, press the igniter button on your keyboard. Click on the water heater’s gas window until you see a blue flame appear in the glass.

Step 7: Continue To Hold Down The Reset Button For 20-30 Seconds.

Keeping the water heater’s igniter pressed down is important. A gas control valve is located directly to the right of the igniter (see illustration). While keeping the reset button down, press the igniter button. Click on the water heater’s gas window until a blue flame appears in the window.

Step 8: Turn The Gas Control Valve To The “On” Setting

On the water heater, there is a gas control valve. The gas control valve may now be turned back to its “On” position, as the pilot light has been ignited by the flame. The word “on” should be in the middle slot at this point.

Step 9: Turn The Thermostat Up

Increase the temperature of the water heater.

Now is the time to dial up the heat in order to get that hot water flowing again!

Step 10: Enjoy Your Warm Water, Or Ask For Help!

If you try to relight the pilot light and it does not stay lit, you may want the services of a professional to assist you with your water heater repair.

But What If You Don’t Have A Manual Igniter?

After that, remove the access panel that is located beneath the water heater thermostat and discard it. You can use a wrench to help you.

After 5 minutes, Turn Gas Control Valve To “Pilot”

Now, set the gas shutoff valve to the “Pilot” position.

Next, Hold Gas Control Valve Down And Ignite Pilot With A Lighter

Keep the gas knob pressed down as you ignite the pilot using a long lighter, similar to a BBQ skewer. If your gas water heater, on the other hand, has an igniting button, use it instead.

Once TheFlame Is Lit,Turn Gas Control Valve to “On”

As soon as the pilot light is lighted, you may remove the reset button and turn the gas knob to the “On” position, which will take around 30 seconds. You should be able to hear the main burner turn on at this point. Your pilot light should now be able to maintain a flame, and hot water should be flowing again!

Furnace Pilot Light: Where It Is And What Does It Do?

Having lit the pilot light with the reset button for 30 seconds, you may now turn the gas knob to the “On” position by releasing the button after 30 seconds. You should be able to hear the main burner turning on at this point. Once this is completed, your pilot light should remain on and hot water should be flowing again.

Why Furnace Pilot Light keeps going out

There are a variety of reasons why the pilot flame on your furnace continues flickering out of control. Let’s get started!

Faulty Thermocouple Triggers Pilot Light to Go Out

It is meant to shut off the gas valve if the pilot light goes out, and it is used in conjunction with a thermocouple. Thermocouples can be damaged or worn out over time. If the thermocouple is incorrectly positioned or malfunctioning, the gas valve may be incorrectly shut off, as well as preventing the pilot light from keeping lit.

Dirty Thermocouple Makes Pilot Light Keeps Going Out

A filthy thermocouple may cause the safety mechanism to mistakenly trigger, causing the ignition to be turned off. The thermocouple has the potential to accidentally shut off the gas valve and extinguish the blazing flame.

Filthy Pilot Port/Orifice

Examine the flame. If the flame is becoming orange, contact an HVAC professional immediately. If you light your pilot and the flame is yellow, this indicates that your pilot opening is filthy and is preventing your pilot light from keeping lit for long periods of time. A buildup of dirt in the pilot light port might prevent the flame from fully enveloping the thermocouple, which can result in a faulty ignition. As a result, the safety system is activated, which results in the gas being turned off.

Bad Gas Regulator

If you have gas appliances in your house, you will also have a gas regulator outside of your home to regulate the flow of gas into your home. Your furnace may not receive enough gas to keep its pilot light lit if your gas regulator isn’t functioning correctly. There is a good chance that you have a defective gas regulator if the pilot light is out in more than one home appliance, such as your water heater.

Bad Flue Venting Could Blow Out Pilot Light

Excess wind might enter via the openings in your flue pipe if it is loose, broken, or not correctly attached to the furnace. This would extinguish the pilot light flame.

A Strong Draft

There’s always the potential that a powerful draft knocked out your pilot light’s flame and caused it to go out.

How To Re-Light A Furnace Pilot Light?

The first and most crucial step is to locate the owner’s manual for your heater. The handbook will assist you in gaining a better grasp of the internal workings of your individual appliance.

Step 2: Identify Pilot Light

Find the location of the pilot light in your furnace by consulting the owner’s handbook. In order to get access to the furnace, you will need to remove the front of the furnace.

Step 3: Turn OFF Gas

After that, locate the gas valve and shut it down completely. A tiny valve located towards the bottom of the furnace is standard on most models. In general, there are three settings for the gas valve: “ON,” “OFF,” and “PILOT.” Make sure the valve is in the “OFF” position by turning it clockwise. It is critical that you wait for at least 5 minutes after the previous step to ensure that all gas has been expelled from the pipes before proceeding. A disaster might occur if this is not done.

Step 4: WAIT 5 Minutes, then Turn Gas to “Pilot”

After that, locate and shut off the gas valve. Near the bottom of the furnace, most furnaces contain a tiny valve to regulate the temperature. Overall, the gas valve may be adjusted to one of three different positions: ON, OFF, and PILOT (pilot mode). Make sure the valve is in the “OFF” position by turning it counter-clockwise. To guarantee that all gas has been removed from the pipes before proceeding to the next procedure, it is critical to wait for at least 5 minutes. A disaster might occur if this is not accomplished.

Step 5: Hold Reset Button

After that, hold down the reset button. However, if you are having difficulty locating the reset button, your furnace’s owner’s handbook should be able to point you in the appropriate place.

Step 6: Press Igniter While Holding Reset Button

Holding the reset button down for a second or two will allow you to activate the igniter and light the flame. Once the flame has been ignited, remove the igniter and continue to hold down the reset button until the flame has been extinguished. Keep the reset button pushed for 20-30 seconds to complete the process. To light the pilot when you do not have a manual igniter, you can use a BBQ lighter or a match. furnace with a pilot light

Step 7: Turn Gas to “ON” position

Restore the pilot light by turning the gas control valve back to its “ON” position once it has been re-ignited. Right now, you should be able to keep your house warm!

Step 8: If you Aren’t comfortable yet, call a pro!

If, despite doing the necessary measures, you are still unable to keep your pilot light lit, contact an HVAC professional for furnace repair.

Boiler Pilot Light: Where It Is And What Does It Do?

The pilot light in your boiler is vital for the boiler to function properly and generate heat. It is necessary for the pilot to burn constantly in order for it to ignite the gas when the gas valve is opened. When this occurs, your boiler starts heating the water, which is subsequently dispersed throughout your house to provide warmth.

If your pilot light goes out, your boiler and central heating will not be able to operate properly. The pilot light is placed within your boiler, on the other side of the valve from the gas valve. The boiler handbook should help you have a better knowledge of the location of each component.

Why Boiler Pilot Light Goes Out

A malfunctioning, misaligned, filthy, or damaged thermocouple is frequently the source of your pilot light’s failure to illuminate properly. It is the thermocouple that keeps the gas valve from opening if the pilot light is not lit. Your pilot light may not function properly if there is an issue with your thermocouple, or if it is just coated with dirt and debris.

Dirty Pilot Opening

When you turn on your furnace pilot light and find a yellow flame, this indicates that your pilot light is unclean and is causing your furnace pilot light to constantly turning out. If dirt accumulates in the pilot light port, it may prevent the pilot light from completely enveloping the thermocouple with the flame it produces. This causes the thermocouple safety system to be incorrectly activated, resulting in the gas being turned off and the heat being turned off.

Weak Gas Regulator Can Make Pilot Light Keeps Going Out

If you have gas appliances in your home, you will have a gas regulator outside your home. The failure of your gas regulator may result in your furnace not receiving enough gas to keep its pilot light lit. In the event that you observe pilot light issues on more than one device, such as your water heater, it is possible that your gas regulator is broken or weak.

A Strong Draft

A strong airflow has the potential to completely extinguish your pilot light.

How To Re-Light Boiler Pilot Light

Make sure you are familiar with the components of your boiler by reading the instruction manual thoroughly. It is common for the owner’s handbook to contain instructions for re-igniting the pilot light.

Step 2: Shut OFF Boiler

Starting with shutting off the boiler is always a good idea.

Step 3. Shut OFF Gas

Locate the gas valve and turn it to the “OFF” position.

Step 4. Wait 10 Minutes

Continue to check the pipes for around 10 minutes to ensure there is no residual gas.

Step 5. Open Boiler and Locate Pilot Light

After a short period of time, you can turn on the boiler. To obtain access to the pilot light, remove the access panel from the wall. Typically, this panel is positioned next to the gas control knob box, which is where it gets its name. Sometimes you may simply lift the panel up, but other times it may be screwed to the wall or ceiling.

Step 6. Turn Gas to “Pilot”

Now, set the gas control valve to the “Pilot” position on the pilot valve.

Step 7. Hold Reset Button, Then Click Igniter

Next, press and hold the reset button for a few seconds. While still holding down the reset button, press and hold the igniter button until you see a flame appear. It is necessary to press the reset button for an additional 20-30 seconds after the flame is ignited to ensure that it is fully functional.

Step 8. Turn Gas Control Valve To “On” Setting

Restore the pilot light by turning the gas control valve back to its “ON” position once it has been re-ignited. Right now, you should be able to keep your house warm!

Step 9. Relax in Comfort

How did things turn out? If not, when will you get your home warm and comfortable? If your pilot light has been struggling to keep a flame, or if you are still unclear how to fire your pilot light, boiler repair is simply a phone call away!

Now that you don’t have to struggle with a cold house anymore, you may turn to a licensed professional with your queries and concerns. To arrange a boiler repair, call or go online to this page. With the help of superTech HVAC Services, you can relight your pilot light in no time.

How Do I Prevent My Pilot Light From Going Out?

Keeping your water heater, furnace, and boiler in good working order can keep those annoying pilot lights from going out on you. An experienced technician will do a maintenance check on the pilot light and thermocouple, as well as clean them both, to ensure that they operate at peak efficiency. Depending on the appliance, a professional will also check all of the connected pipes and wiring, the flue venting, and all other functional aspects of the appliance to verify that each portion is running at peak efficiency.

Maintaining your furnace, water heater, and boiler on a regular basis is essential to ensuring that your heat or hot water never runs out!

Soak Up The Warmth!

That’s all there is to it! A basic description of how to relight your pilot light, as well as the most typical causes for your pilot light to go out is provided. We all know that having no heat or hot water in your house is the worst feeling in the world! The best course of action if you’re having difficulties keeping your pilot light lit or are still unclear about the process is to call a professional. If you are experiencing any pilot light issues, please don’t hesitate to contact us at (443) 219-7798 or make an appointment onlinehere.

Leave a Reply

Your email address will not be published.