How To Pump Water Out Of Pool

How to Drain Water from Your Swimming Pool

So, how long should I wait before draining my swimming pool?

  • Pinch A Penny experts may propose that you remove part of the water from your pool and replace it with fresh water if your water has a high amount of Total Dissolved Solids (TDS)
  • However, this is not always the case. It is also recommended to drain some water if you know that a strong tropical storm or hurricane is approaching
  • This will help to prevent overflow. In the event that you require a repair or resurfacing, the technicians will handle the process for you.

Regardless, contact with a professional first before opting to remove water from the system. These procedures are applicable to both inground and aboveground pools, as well as saltwater and chlorine-treated pools, among other things. If you determine that draining the water from your swimming pool is a required step, this article will explain you how to do it, no matter what sort of filter you have. We do not advocate draining a pool past the skimmer line unless absolutely necessary. This may cause your pump to become inoperable, resulting in damage or destruction.

1.

  • No matter what you decide, talk with an expert first before taking any action. Inground and aboveground pools, as well as saltwater and chlorine-treated pools, are all covered by these instructions. When it is decided that this is a required step, this article will teach you how to drain water from your swimming pool, no matter what sort of filter you have installed. Pools should not be drained past the level of the skimmer line, according to the manufacturer. This might cause your pump to become inoperable, causing damage or even destruction. A Cartridge Filter is used to drain the pool. There are two options for individuals who have a cartridge filter and want to clean their pool. The Drain Plug is utilized in the following ways:

Use of the Drain Valve- If your system has a valve between the pump and the filter, you can drain the system through it.

  • Remove power from the pump and twist the valve such that it prevents water from flowing through the filter
  • When you turn on the pump, water will begin to flow out of the aperture. As soon as you’ve extracted enough water, switch off the pump and reposition the three-way valve to its original position on the pipe. Water can flow backwards from the pump and into the filter in this manner.

How to Drain a Pool Using a Sand Filter (with Pictures)

  • Turn off the water pump. Backwash hose should be rolled out into the yard or a designated drainage place
  • The “Waste” position is reached by rotating the multiport valve on the top or side of the tank in a clockwise manner
  • Restart the pump by pressing the button. You should switch off your swimming pool pump once you have removed the appropriate amount of water from it. Rotate the multiport valve in a clockwise motion from the “Waste” position back to the “Filter.” Pick up the backwash hose to assist in draining all of the water out, and roll it back up again

How to Drain a Swimming Pool Using a DE Filter

  • Manually turn off the pump at the circuit breaker box. Using a clockwise motion, turn the multiport valve until it reaches the “Waste” position. Restart the pump by pressing the button. The pump should be turned off once you have removed enough water from your swimming pool to be safe. The handle on the multiport valve should be rotated in a clockwise manner until it returns to the “Filter” position. Restart the pump by pressing the button.

In the event that you have any more queries, please contact your local Pinch A Penny. To locate a store near you, please see the list below. Locate a Pinch a Penny store in your area.

How to Drain Last Bit of Water from Pool

Every swimming pool owner is aware that it is important to drain the water from the pool from time to time for a variety of reasons. There might be a variety of reasons for this, including the need to replace your pool liner or the presence of hazardous environmental conditions. Once the water has been emptied from your pool, it may become vulnerable to further harm. It’s critical to understand how to drain the final bit of water from a pool in order to reduce the chance of damage. Pool draining should be done with care, however bear in mind that while winterizing your pool, you should avoid draining the whole contents of the pool.

Draining Pool Water Using an Electric Pool Pump

In order to drain your pool water with an electric pool pump, follow the instructions outlined below:

  1. Insert the intake line of the pump into the water as near to the middle of the pool as feasible
  2. Place the pump’s outlet hose at a location on your property that is not near the swimming pool or spa. If you are unsure of where to drain your pool water, make sure to find a level area to avoid flooding
  3. Otherwise, you may experience problems. Turn on the pool pump if it is not already running. Check to see if the water level has dropped before leaving the process unattended, and don’t forget to check on it on a regular basis to avoid faults
  4. And Close all of the machinery when the water level falls below the minimum necessary to permit additional draining, which is normally between 6 and 12 inches deep.

Draining Pool Water Using Garden Hose Siphon

Using a garden hosesiphon to drain water from your pool is a more time-consuming option. You may use a single garden hose, but if you want to drain the water more quickly, you should use many. Please follow the steps outlined below.

  1. Underwater, submerge the whole hose (or each individual hose if you are using more than one)
  2. Take one end of the hose and place it in a location that is not near the pool. Select a level piece of ground. The other end of the hose should be buried in water until the job is finished. Keep an eye out to see whether the water starts to siphon out
  3. Check the draining process on a regular basis to ensure that the water level reduces and that flooding does not occur. Garden hose siphons, like electric pumps, will not totally remove pool water from the pool. It is necessary to remove the hoses if the water level is between 6 and 12 inches deep.

Draining the Remaining Water from Your Pool

Because none of the two draining procedures will completely drain the pool water, you will need to remove any excess liquid that remains at the bottom. You can do it in the following ways:

  • Using a wet vacuum, remove the stagnant water from the area. Drain the liquid by sweeping it down the drain
  • In order to get rid of excess water, remove the pool liner and flip it over anywhere on your land.

Important Considerations When Draining Your Pool

To remove the stagnant water, use a wet vacuum. Drain the liquid by sweeping it down the drainpipe; and Get rid of excess water by removing the pool liner and flipping it somewhere on your land.

  • Loss of Shape – Water, of course, aids in the preservation of the shape of your pool. As a result, it is critical to drain the water on a day when the weather conditions are favorable for draining the water. Is it necessary to winterize my pool is another issue that pool owners frequently ask. Molds – A pool without water can serve as a breeding environment for molds, so once the water has been drained from the pool, take precautions to avoid the growth of mold on the liner. In most cases, mold grows as a result of storing the liner without thoroughly drying it
  • Sun Damage – Water acts as a barrier between your pool’s liner and the elements. Whenever the pool is not filled with water, the liner becomes more vulnerable to deterioration and warping caused by the sun’s ultraviolet radiation.

Questions

When using a hose to drain your pool, just insert one end of the hose into the drain port and attach the other end to a submersible pump. The hose and pump should be submerged in the deepest portion of the pool, preferably near to the drain.

Can you Drain a Pool and Leave it Empty?

You can, but keep in mind that there are certain maintenance hazards associated with it, like as damage and mold growth.

Make sure to take additional precautions to keep your pool liner from becoming damaged or losing its form.

Does Draining a Pool Damage It?

It is dependent on the situation. Of course, if you drain your pool at the wrong time or under the incorrect conditions, you run the danger of causing damage to your pool liner and structure. With a fiberglass pool, the possibility of damage increases exponentially.

Bottom Line

Learning how to drain the final bit of water from a pool will help you avoid causing major damage to your pool. There are two primary methods for accomplishing this: by utilizing an electric pool pump or by employing a garden hose siphon. Please contact us if you have any queries. Our team of specialists here at Teserra Outdoors is ready to assist you in creating your ideal pool.

How to Empty a Pool Without a Pump

It is not as tough as it may appear to empty a pool without the use of a pump. This method eliminates the need for scooping and dumping and allows for a very quick pool emptying. Even though you may want some assistance in getting it started, the rest will be simple: just sit back and wait for the water to drain away.

Step 1

It is not as tough as it may appear to empty a pool without a pump. This method eliminates the need for scooping and dumping and allows for a faster pool emptying time. Once it has started, you may want some help, but once it has begun to drain, all you will have to do is sit back and watch.

Step 2

Bring the other end of the hose to the location where you want the water to drain. If you want to empty the pool as quickly as possible, you can use more than one hose.

Step 3

Fill the pool with water by sucking on the end of the hose with your lips until the water drains out. Spit the water out of your mouth. Do not take it down your throat.

Step 4

It is important to understand that once the water begins to flow, it will continue to flow until air enters the end of the hose that is located in the pool. By doing so, you are allowing the natural forces of gravity and air displacement to do their work and drain your swimming pool.

Step 5

Check the hose or hoses on a regular basis to ensure that they are still running and that the end in the pool remains below the surface of the water at all times.

How to Lower the Water Level in an In-Ground Pool

A strong downpour can cause the water level in your pool to rise to dangerously high levels. Following a severe storm, you may need to drain some of the water from your in-ground pool to avoid an overflow and consequent damage to the pool decking and surrounding vegetation. You may also need to drain water from your pool if you accidentally leave the hose on and overfill it, or if you’re preparing your pool for the winter. If your pool has a multiport valve on the filter or a drain spigot on the pump, you may be able to reduce the water level by turning on the multiport valve or turning on the drain spigot.

Using the Multiport Valve

An automatic multiport valve is required for pools with sand or DE filters. This valve is utilized to backwash the filter when it becomes clogged with debris. To drain water from the pool, you may use one of two settings on this valve – Backwash or Waste – depending on your preference. Both options cause water to be discharged through the drainage port.

The distinction between Backwash and Waste is that Backwash sends water backward through the filter, but Waste bypasses the filter entirely. Use the Backwash setting if you want to clean your filter as it drains by using the water that comes out of the drain.

Using the Pump Drain Plug

A cartridge filter does not necessitate the use of a multiport valve since the cartridge may be removed when the filter needs to be cleaned. Nonetheless, the pump may be equipped with an internal draining spigot, which should be located between the pump and the filter. Connect a hose to the spigot and turn on the water. The pump will take care of the rest.

Using a Submersible Pump

A submersible pump is meant to operate underwater, and you may already have one in place to keep the water out of your pool cover during the colder winter months. To empty the pool, you just hook a drain line to it and then lower the pump into the pool, allowing it to settle to the bottom. Connect it to a power source, and it will pump water through a drain line to a designated drainage location. You should use this option if you do not have access to a drainage spigot or a multiport valve.

Siphoning Water from the Pool

If you’re in a hurry, you can drain the water from your pool with nothing more than a garden hose. Simply drop one end of the hose into the pool and carry the other end to a lower elevation, such as the bottom of the pool steps, to drain the pool. In order to get the flow going, you must first establish negative pressure in the pipe. This is frequently accomplished by letting the free end of the hose drop fast or sucking on the end of the hose. If the thought of sucking pool water makes you nauseous, fill the hose halfway with water and put a nozzle onto one end of it.

The flow of water through the hose will provide the negative pressure that will allow the drainage process to begin as quickly as possible.

See also:  Why Isn T My Electric Water Heater Working?

Drain Water Responsibly

Even lowering the level of a reasonably sized 20-by-20-foot pool by 4 inches results in the loss of about 1,000 gallons of water. It is possible that you and your neighbors will experience flooding as a result of this large amount of water. Keep the water flowing into a drainage sewer or out onto the street to prevent creating such difficulties in the future. If you live in the country, look for a natural drainage system that will securely transport the water away from your property.

Tips for Winterizing Your Pool

Several considerations should be taken into consideration while emptying your pool to prepare it for winter:

  • Allow the chlorine level to decrease to less than 1 part per million (ppm) before emptying to avoid introducing chlorine into the surrounding environment. After you’ve completed emptying the pool, you should balance the pH and add extra chlorine to bring the level back to between 1 and 3 parts per million (ppm). If your pool has a vinyl liner, you should avoid entirely emptying it. In the cold winter temperatures, this can cause the liner to loosen and, in some cases, even break. It’s only necessary to drain the water down to just below the skimmer level if your pool has a gunite or tile liner and you’re using a tarp or solid cover to keep the pool protected. Put a pump on the lid to keep the water from freezing over during the winter
  • And As soon as the water level falls below the skimmer, switch on the pump for a few minutes to allow the water to drain out of the pipes. Do not allow the pool lights to get partially submerged in water. During the winter, this might lead them to crack or shatter. They should either be entirely exposed or completely submerged
  • Neither is acceptable.

How to Pump Water Out of Pool: For Above Ground & In-Ground Pools

For both above-ground and in-ground pools, you may learn how to pump water out of your pool by reading this article. Disclosure: It is possible that this content contains affiliate links. This means that if you make an eligible purchase, we may receive a small commission at no additional cost to you. There are times when you may need to drain your swimming pool for a variety of reasons, including maintenance, winterization, or just to change the water after several years of usage. Dona Hall contributed to this article.

My internet study on how to pump water out of a pool came up empty, and I was unable to find a step-by-step instruction to assist me with this difficult task.

As a result, I’m here today to assist you with pumping the water out of your swimming pool – whether it’s an above-ground or an in-ground pool. We will look at how to drain water from swimming pools using garden hoses and pumps in this lesson.

Things You Will Require

For both above-ground and in-ground pools, you may learn how to pump water out of your pool by clicking here. Disclosure: There may be affiliate links in this article. Essentially, this means that we may receive a tiny commission on qualified transactions, at no additional charge to you. There are times when you may need to drain your swimming pool for a variety of reasons, including maintenance, winterization, or just to change the water after several years of usage. Dona Hall contributed to this report.

Consequently, I’m here today to assist you with pumping the water out of your swimming pool — whether it’s above-ground or below-ground.

  • If you reside in an area where there is a lot of ground water
  • If you don’t know what sort of pool you have, ask your neighbors. If you are unsure about the sort of equipment that is installed in your swimming pool, consult with a professional.

In light of the foregoing, the following are the items that you will want in order to drain an Above Ground Pool:

  • A pump
  • A garden hose
  • A broom
  • A vacuum hose/sunny day/towel

The following items are required for draining an in-ground pool:

Guide for Draining an Above Ground Pool

In this section, we will look at two different approaches for draining this sort of pool:

Siphoning Your Pool

Perhaps you’re wondering what the procedure entails and what actions are required. Here are the details: The first step is to make sure that you have enough hose to extend from your pool to the location where you want to dispose of the water once you drain it. By just using the drain plug to drain water from your pool, you risk having your pool’s surface washed away and the pool collapsing in, resulting in harm to the pool’s structure. If you’re going to be at home for a few days, choose a day when there will be plenty of sunshine is a smart option.

  • The general rule of thumb is that the larger the hose, the faster the pool will drain, and the smaller the pool, the faster the pool will drain, respectively.
  • That’s something you shouldn’t do!
  • Then, quickly remove the garden hose end from the tap while keeping it near the ground (below pool level), and the water will begin to flow out of the pool again.
  • The next step is to use a broom to remove any remaining water that may have accumulated after the hose has completed its task.
  • It was the finest of the best.

The next step is to either leave your pool to dry in the sun or cover it with a large number of towels to guarantee that it is completely dry. Alternatively, if you have a vacuum hose, you might utilize that.

Using an Electric Pump

This procedure is comprised of four basic steps: To begin, follow the first two procedures outlined above for emptying a pool using siphoning. The second (or third) step is to connect a pump to the garden hose, submerge it in your swimming pool, and start pumping water out of the pool. During this process, you can use another hose to suction away dirt when the water level drops to around 10 inches or less. Also, bear in mind that as you continue to drain the water, you may need to maintain the hose at a lower level than your pool in order to avoid overflowing it.

Even if you are utilizing a pool drainage pump, you may still need to sweep out any little amount of water that may have accumulated in the drain.

Alternatively, you might use a large towel or hang it out to dry in the sunshine.

Guide for Draining an In-Ground Pool

You will need to do the following measures in this situation: When it comes to draining an in-ground pool, there are three key considerations to keep in mind. To begin, switch off all of the return lines to your swimming pool. Second, as the water level in your pool begins to drop, be certain that no air is sucked into the drainage line into your pool. If this occurs, the pool pump will lose power, and the water will cease to circulate. Third, determine where the water will be disposed of. Each of these factors will be examined in further detail in the following sections.

  1. Draining the water down your home’s sewer clean-out, which is normally positioned near your house or on a wall, is the proper procedure to follow.
  2. If you discharge an excessive amount of water into your sewer system, there is a potential that surplus water will back up into your home or business.
  3. If you wish to operate off of a ball valve, just reduce the valve’s opening to half its size.
  4. A lot of the time, the water in your swimming pool will circulate through its filter and back into the pool.
  5. Another issue to consider is that if you cut off the return line and only open the waste line, the waste line (which goes to the street) will not be large enough to handle the pressure generated by the pump.
  6. When using a De or Sand filter, turn off your pool pump and rotate the knob on your multiport valve/regulator to the “Waste” position.

To start the pump, make sure that a waste line is connected to the “waste” port and then turn the power on.

If your pool is equipped with a cartridge filter, open the ball valve that connects to the waste stream. If you just have a garden hose outlet purging connected to your swimming pool water, you might want to consider upgrading it with a 1.5″ ball valve instead. When the water level in your pool drops below half of the aperture of the skimmer, you must switch off the skimmer suction to prevent air from entering the suction line and interfering with or shutting down your pump. You should also consider turning off the suction line if you are using a suction cleaner with a suction line connected to it.

  • As an added precaution, turn off the Spa drain before it completely empties out the pool and the system begins to draw air via the port.
  • It is necessary for the water to travel from this drain to the pump and subsequently to the drain port.
  • If it becomes clogged, you will notice a reduction in the amount of water that flows through your pump’s strainer cover.
  • They will be bringing their own garbage hoses with them.

In Conclusion

Don’t pour your pool water into the gutters, storm drains, or streets; otherwise, you may be in violation of municipal rules and regulations and fined for water waste. Drain the water from your swimming pool into your sewer system so that it may be recycled and repurposed. That is how I was able to complete the difficult process of emptying my swimming pool. If you like the post and have any comments, criticism, or questions, please let us know by leaving a remark in the box below. Also, please share this post with your friends to ensure that the entire world is aware of how to pump water out of a pool.

How To Drain An Above Ground Pool (In 3 Easy Steps)

First and foremost, I’d want to emphasize that you should only ever have to empty your pool when absolutely necessary. In fact, emptying it for the winter is not recommended since it might cause your liner to dry out and break as a result of exposure to the elements. However, there are a few circumstances in which you may be required to drain an above-ground pool. And even if you do need to call a professional, there is typically no need to do so. If you know what you’re doing, it’s really simple to do it yourself.

4 reasons to drain an above ground pool

One reason you might need to drain your pool is if you have one of the following:

  • 1Replace the pool liner with a new one. This is most often caused by a rip or leak. In this circumstance, there is no getting around the need to empty the pool
  • 2to start the season fresh with new water. If you correctly close your pool, you shouldn’t have to do this, but things happen, and occasionally, despite our best efforts, we don’t get everything done. in the event that it is not completed properly
  • 3to have the pool removed from your yard or replaced That’s enough for now
  • 4 To correct the chemistry of your pool as a result of chlorine lock. Chlorine lock is one of those water problems that no amount of chemical treatment can correct. In fact, the more chemicals you use, the worse the situation becomes for you. It occurs when there is an excessive amount of pool stabilizer (or cyanuric acid) present in the pool or when the pH levels are out of equilibrium. Because of this, chlorination is rendered ineffective, and the only option to correct the situation is to remove part of the over-treated water and replace it with fresh water.

How to drain an above ground pool

When it comes to emptying an above-ground pool, you essentially have two options: you can either use a submersible pump or siphon the water out using a garden hose. I personally advocate utilizing a mix of the two methods since siphoning is very quick, but a pump will assist in removing the remaining foot or so of water that the siphon can’t quite get to with the siphon alone.

However, this is only applicable if you are entirely draining the tank in order to replace the liner. If you’re simply draining a portion of it to rectify the chemistry, a garden hose will suffice and save you the money on the added purchase of a skimmer.

Step 1. Figure out where to dump the water

Before you begin emptying the water from your pool, you’ll need to choose where the water will be disposed of. When draining a pool, you should check with your city to determine if there are any particular rules controlling pool water disposal. This is especially important if you’re emptying an entire pool since some areas mandate that pool water be deposited into the sewer system because of the chemicals.

Step 2. Start a siphon

5/8 in. x 50 ft. Heavy Duty, Lightweight, Drinking Water Safe Garden Lead-In Hose by Flexzilla (HFZG550YW) Flexible Garden Lead-In Hose by Flexzilla (HFZG550YW)

  • We employ a very flexible polymer blend to construct our distinctive green hoses, which enables for all-weather flexibility in temperatures ranging from -40° to 140°F. This makes it simple to use even in the most extreme situations. Extremely durable – designed to withstand the rigors of any industry or climate. This hose’s abrasion-resistant outer cover and crush-resistant anodized aviation aluminum fittings ensure that it is always ready to perform
  • Nonetheless,

Once you’ve selected where you want the water to travel, you may siphon it using one of two methods: either cut a few feet off either end of a garden hose to make a siphon, or use a whole garden hose and faucet to siphon the water. If you’re going to cut your hose, a part that’s around 6-8 feet long will generally be plenty. Basically, you’ll just submerge the entire hose in the water and then, while holding one end of the hose in your hand, swiftly draw that end out of the pool and direct it downward, just below the surface of the water.

See also:  How Long Does A Tankless Water Heater Last

This is best done with two individuals so that one of them can cover the open end of the hose to prevent water from escaping throughout the process.

Step 3. Drain the water

You’ll simply withdraw your hand from the severed hose siphon once you’ve dropped the un-submerged end to the ground and let the water to drain. You will submerge the entire hose in the pool once it has been completely filled and then pull out either a clamp or your hand from underneath it until there is just approximately four feet of hose remaining above water. When you’re finished, drop the hose to the ground, removing any clamps or covers that may have been on the other end, and the water should begin to flow through the hose again.

Step 4. Remove the remaining water

This step is only necessary if you need to replace your liner and want to ensure perfect drainage. There are a variety of methods for accomplishing this, but the quickest is to suck it out using a pump or a wet/dry vacuum. If you just cannot afford to spend the money, you can use buckets or other containers to remove as much as you can until the container is empty enough to be handled safely. Some water will almost certainly be discharged during the procedure, so make sure to thoroughly dry the area before putting in a new liner to avoid bacteria and pool algae from growing beneath the surface of the water.

Bottom line

That is all there is to it in terms of explanation. If you’re only draining a portion of your pool, I recommend using the cut siphon approach, simply because it’s a bit simpler to manage than the other methods.

The open end of the pool should be returned to the pool when either technique has drained all of the needed water from it, as shown in Figure 1. Questions? Comments? Leave them in the comments section and we’ll get back to you as soon as possible!

How to use a Submersible Pump to Remove Excess Pool Water

Originally published in April of 2018, this update is for 2020. We were all aware that owning a swimming pool would entail some care, but I had never considered the work required during the off-season; it turned out that I also required a dependable, long-lasting submersible pump for the months when the pool was not in use. Excess water should be drained. Chemistry, algae, filter, heater, chlorinator, skimmer, and pool vacuum are just a few of the concerns that come to mind right away. I don’t want the water from rain or melting snow to overflow during the off-season months, because it would imply reaching the top of the vinyl liner and hitting the coping in my instance, which would be a problem with an inground pool.

Consequently, in addition to my summer pool maintenance manual (which I actually wrote myself and covers everything from backwashing to salt concentrations for optimal chlorination), I developed a procedure for maintaining a low water level in the pool using my Flotec submersible pump, which I can highly recommend after using it in this manner for nearly eight years.

So let’s start with a video to get things started.

A Video: How to Drain Excess Pool Water

Watch the video below to see how I go through my routine while also attempting to keep my dog from jumping into the pool unexpectedly. Thanks for your time!

My Submersible Pump Assembly for Pool Water Removal

To summarize the video, what I have below is aFlotec submersible pump (which is often used as a sump pump), which I’ve modified slightly with the PVC and the check valve assembly that you see on the right side of the picture. The PVC is only there to connect to the pump, however the check valve has a practical purpose in that it guarantees that water can only flow in one direction when the pump is turned on. Take a closer look at the check valve in the photo below; you’ll see that it has directional arrows on it that indicate how to install it and which direction water will be able to flow if it is properly installed.

However, for me, this submersible pump also works as a backup for the sump pump in my house.

Consequently, for the pool water removal setup, a check valve isn’t absolutely necessary, although it doesn’t harm to have one.

Taking a look at the photo below, you can see that I’ve also added a gray plastic collar insert to the blue pool drain pipe, which fits perfectly into the check valve assembly – and that I’m anchoring everything with some extremely low-tech, affordable, and quite effective metal mounting straps.

  1. (It was only recently that I learned that term could be used as a verb.
  2. When I do this (typically once every 4-6 weeks off-season), it’s crucial to remember that it’s usually FREEZING outdoors when I’m working.
  3. Almost a year has passed since I published this post, and look what I uncovered on Amazon today: A Swimming Pool and Hot Tub Pump with Hose that has been completely constructed.
  4. Strangely eerie – yet also rather cool!
  5. Now, let me list down all of the components that I’ll be utilizing in this project, and as always, I’ll include links to Amazon so that you can see more information and costs for each component; the only item that is a little pricey is the submersible pump itself.

It’s in excellent condition, in fact, because it’s meant to be used as a sump pump, which means it’ll stay submerged for the most of the time. Mine is leading a very pleasant life on a shelf in the shed, where it is kept quite warm (and dry) while waiting to be used once or twice a month.

My Pool Water Removal Assembly Part List

MyFlotec Submersible Pump is a type of submersible pump. In this case, the coupling is made of PVC and is screwed on (it is sized to the interface on the pump) (sized accordingly) PVC Glue is a kind of adhesive (to glue the PVC pipe to the PVC coupling; this entire assembly then screws onto the pump) PotentialRubber Couplings to connect your Check Valve to PVC and also to your Drain Hose, which should be sized appropriately. A plastic connector for your drain hose that is the appropriate size.

  • A pool drain line to transport the water away from the pool; this should be at least 50 feet awayFrom the above – which, once again, may alter slightly depending on your assembly – the remainder of the customary activities are performed in the same manner as the movie.
  • 4) Once your submersible pump is submerged and steady, you may turn it on and make sure there are no kinks in the drain hose so that the water does not harm your pool or anything else that could be affected by the water: 5) And, by all means, PAUSE AND REVIEW THIS CAREFULLY!
  • Or, in the worst case scenario, everything.
  • 5/16/20 Update: And now, for a completely indulgent digression.
  • There is nothing to be concerned about.
  • Also, he’s constantly under the watchful eye of everyone in our family.
  • Photograph courtesy of my wife and kid (seen above right).
  • Unsolicited Yorkie Photograph: Quarantine 2020

Off-Season Pool Water Draining: Additional Options…

The other major category of choices for draining surplus pool water during the off-season is a range of pool cover pump types, which are easily accessible in a number of configurations. Designed to sit on your pool cover and drain water that gathers straight off the top of the pool cover, a pool cover pump is an essential part of any pool. In fact, here’s a snapshot of a popular, highly rated (on Amazon) cover pump to get you started. If you like, you can even click on the image to acquire additional information from Amazon.

  • Please note that they appear to be a little less solid than the technique I’ve described above, at least to my eyes.
  • As a result, I’ve personally avoided them — although that doesn’t rule them out as a viable alternative in some situations, particularly if cover opening is an issue.
  • Now, without a doubt, the usage of passive siphons is included in a third category of choices that can be considered.
  • Above-ground swimming pools are the greatest choice since they do not necessitate the use of a hose or a height disparity.

However, there are alternatives accessible for similar situations – alternatives that do not include the risk of drinking contaminated pool water. Is there anyone else who would want to offer their opinions, experiences, or ideas on any of these subjects?

Need Professional Help from a Local Contractor?

Visit our Contractor Finder page for more information.

Related Posts

Salt Water Pool Chlorinator Questions and AnswersRefreshing a Swimming Pool LandscapeMy Battle with Surface Water RunoffBuilding a Removable Wood Fence Section and GateA Rookie Carpenter’s 5-Step Guide: How to Build a Playhouse

How to Completely Drain Water From an Above Ground Pool

The most recent revision was made on September 22, 2021. First and foremost, we must emphasize that you should only have to entirely empty your pool on rare occasions. In fact, doing so may result in damage to your pool liner or other pool equipment. Despite the fact that it is rare, there may come a time when you will need to totally drain your above-ground swimming pool. Even while we recommend that you deal with a pool expert, emptying your above-ground pool is something that many pool owners can safely handle on their own with a little time and effort!

Why Should I Drain My Above Ground Pool?

As previously said, routine maintenance and winterization of your pool should not necessitate the total draining of the water. You run the danger of causing damage to your pool liner as well as the structure of your above-ground pool. Here are a few scenarios in which you would most likely need to dump the entire tank.

  • The removal or relocation of your swimming pool is on your to-do list. You intend to replace the liner of your swimming pool. It is impossible to improve the water quality of a pool with chemical treatments and adequate care

Choose Your Pool Draining Method

If it is time to empty your pool, there are two main options that pool owners typically choose from when getting ready to drain their above ground pool: an electric pump or a garden hose siphon. If it is time to empty your pool, there are two main options that pool owners typically choose from when getting ready to drain their above ground pool. Either option will be effective in draining your pool water. It all comes down to personal inclination, available time, and available equipment. A summary of each drain technique, as well as the procedures required to complete the operation, is provided below.

Option 1 – Pump to Drain Water:

You’ll need an electric water pump for this option, which is not included.

  1. Make that the intake pipe of the pool pump is completely submerged under the water, as close as possible to the center of the swimming pool
  2. Select a location on your property where the pump’s output line may be drained. In order to minimize flooding, this region should be separated from the pool and the earth should be leveled. Clean and dry hands should be used to turn on the electric pump. Before you leave the equipment unattended as it empties, check to see that the water level in your swimming pool is falling when the pump begins to operate. Check on the swimming pool on a regular basis to minimize floods or equipment faults. An electric pump will not be able to completely drain your swimming pool of all of its water. Once the water level has dropped to a point where it cannot be drained any more (6-12 inches deep), turn off the pump.

Option 2 – Use a Garden Hose Siphon:

A single garden hose will suffice to finish this pool draining process; however, the more hoses you use, the faster your water will drain. Using the following procedure, you may siphon water out of a pool:

  1. Submerge each hose entirely so that it fills with the water from your above-ground pool
  2. Drain part of the garden hose from the pool and position it on flat ground in a location that won’t be flooded. Maintain the submerged position of the other end of the hose in the water and ensure that the liquid begins to siphon out of the pool. Check the siphon on a regular basis to ensure that the water level continues to fall and that there is no flooding. When compared to an electric pump, this approach drains at a more leisurely pace. Garden hose siphons will not completely remove the water from your pool. Remove the hoses as soon as the water level has stabilized (about 6-12 inches deep)
  3. And

How to Remove the Remaining Water from Your Above Ground Swimming Pool

Make sure each hose is fully submerged so that it may fill with water from your above-ground pool. Remove one end of the garden hose from the pool and position it in an area with flat ground so that it will not flood. The other end of the hose should remain submerged in water, and it should begin to siphon the liquid out of the pool. Check the siphon on a regular basis to ensure that the water level is decreasing and that there is no flooding. Compared to an electric pump, this approach drains at a slower rate.

Remove the hoses as soon as the water level has stabilized (about 6-12 inches deep).

  • Using a Wet Vac to remove surplus water from the carpet
  • Using a broom, sweep the leftover water into the pool’s drain. removing the liner from the pool’s frame and tipping it over so that the excess water may be dumped (with caution) onto your land

Risks When Draining Your Pool Completely

Despite the fact that the procedure of emptying your swimming pool is basic, there are certain hazards connected with this maintenance operation, particularly with the pool liner.

If you are not emptying your above-ground pool to replace its liner, there are several crucial considerations to make before you begin in order to safeguard the integrity of your pool, which include the following:

  • Loss of Form: Due to the presence of water, above-ground swimming pools maintain their shape. When approximately 75% of the liquid has been drained from the pool, considerable distortion will occur. To avoid having your pool collapse, drain it on a day when there are no high winds or harsh weather that might cause the empty pool to become damaged
  • This will help prevent your pool from collapsing. The sun’s rays cause the following damage: The water in your swimming pool helps to preserve your liner from damage caused by ultraviolet rays. As soon as the water has been entirely removed from the pool, the liner is at risk of warping and fading due to the sun. The pool specialists at LinerWorld recommend emptying your above-ground pool when the weather is cloudy outside. Mold Development: If you’re draining the water from your pool in order to transfer it, it’s critical that you take additional precautions to avoid mold growth on the liner of your pool. Mold can grow in these situations if you pack up your liner before it has had a chance to properly dry off. Always dry vinyl thoroughly before storing it, either with towels or a wet vac
  • Otherwise, it may crack.
See also:  How To Light Pilot Light On Water Heater

Preparation is essential before beginning this procedure. Decide on the drain technique you’ll use, make sure you have the necessary tools on hand, and check the weather forecast to ensure that you’ll have the least amount of damage possible. Before beginning this process, LinerWorld always suggests speaking with a pool expert if you have any questions or concerns. You may save even more money by exploring LinerWorld’s extensive range of colorful and eye-catching swimming pool liners when you’re emptying the water from your pool because you need to replace your liner.

How to Drain An Above Ground Pool

The summer has come to an end, and it is time to put your above-ground pool in storage. But first and foremost, you must drain all of the water. Here are two simple methods for doing the task: with a pump and with a hose siphon, respectively. Method 1: Using a Pump A medium-sized water or vacuum pump will suffice for this task.

  1. In order to get the pump’s intake hose to the middle of the pool (or as near to it as possible), you must unroll it and submerge it in the pool
  2. Place the outlet hose so that the water departing the pool does not overwhelm the surrounding area, but instead drains away from the pool
  3. Ensure that your hands are completely dry. In order to use the pump, connect the electric wire to an electrical outlet and turn it on
  4. Check to see that the pump is doing its function and then turn it on. Check the operation on a regular basis, and keep an eye on the water level. According to the size of the pool and the rate at which it is being pumped, this procedure might take several hours. When the water level becomes too low for the pump to drain it properly, turn off the pump.

Method number two: the hose siphon Draining the pool will necessitate the use of at least one garden hose. The greater the number of hoses you utilize, the faster the pool will drain. A word of caution: avoid starting the siphon process with your mouth, or you may wind up swallowing a mouthful of pool water.

  1. Set up each hose in the pool so that it is totally submerged in water and completely filled with water
  2. One end of each hose should be lifted out of the pool and set down on the ground. Make certain that the opposite end of the hose is completely immersed. Water volume, quantity of hoses, and diameter of hoses all have a role in how long it takes to drain a swimming pool properly.

Remove any residual water by either removing the drain cap (if there is one) or deconstructing the pool until you can free the liner, depending on which procedure you choose to use. Either turn over the pool liner or scoop the water out of the pool to drain it completely.

How to Drain Your Swimming Pool (Properly)

You may use this method to correct issues and clean your swimming pool quickly whether you need to rebalance your chemicals, decrease your TDS (total dissolved solids), or just clean up an inground pool that has not been properly maintained. It is not recommended to drain a fiberglass or vinyl liner pool. When exposed to direct sunshine, fiberglass can float, and vinyl liners are known to expand significantly. Once a vinyl liner has been refilled, it will frequently have crinkles in it and will never look the same again.

  1. Make sure you are aware of the dangers associated with emptying your swimming pool.
  2. If there is water saturation in the ground around the pool, it is possible that damage will occur due to hydrostatic pressure if the pressure release valve breaks.
  3. For further information, please refer to our drain and acid wash disclaimer.
  4. There have actually been cases of pool service workers falling in with a pump that was not adequately shielded and being seriously injured or even died as a consequence of the accident.
  5. While drawing water from the main drain and directing it down the backwash line may be effective in some situations, it puts your pool pump at danger of losing prime and running dry in other situations.
  6. In addition, the process of draining might expose plaster and surfaces to the environment.
  7. Here is a link to a disclaimer regarding pool drains and acid wash.

The procedure for emptying a swimming pool is outlined below.

A number of Home Depot locations were available in the Dallas, TX, region.

Take care not to leave the pump running when it is not needed.

Once the pump is required to lift water three or four feet above the water level in the swimming pool, it may be difficult for the pump to maintain its prime.

2.) Start the pool pump to drain the water from the pool.

If there is a lot of debris and muck in the pool, it is generally best to leave it on the surfaces and allow it to dry up completely.

3.) Pick up any rubbish that has accumulated on the floor.

When there is extensive algae accumulation to the point where the surfaces are mostly slimy or carpeted, however, I would recommend leaving the material where it is to dry up completely.

When something is very hefty, it is also tough to dispose of.

If you’re going to use muriatic acid (which is typically used to reduce the pH of pool water), make sure to dilute it with water by at least 50%.

This substantially slows down the etching process and allows the acid to do more to whiten and brighten the plaster without causing it to become rougher and more uneven.

If you don’t have an overflow line, make sure to be present when the last amount of water is added.

6.) Add starter chemicals to the tap water to convert it to pool water before using it. These chemicals may be purchased for roughly $150 at a retail store. I’ll make an attempt to add another post on what’s required as soon as possible.

Build the Pool of Your Dreams

Whether you need to rebalance your chemicals, decrease your TDS (total dissolved solids), or just clean up an in-ground pool that hasn’t been maintained, draining all of the water from your swimming pool will help you address your problems and clean it quickly and efficiently. It is not recommended to drain a fiberglass or vinyl liner swimming pool. When exposed to bright sunshine, fiberglass can float, and vinyl liners will normally expand. It is common for a vinyl liner to develop crinkles after being refilled, and the liner will never look exactly the same again.

  • When emptying your swimming pool, make sure you are aware of the dangers.
  • Occasionally, if there is water saturation in the ground around the pool, and the pressure release valve breaks, you may have damage due to hydrostatic pressure.
  • Check that the pump you are using is connected to an electrical connection that has a correct ground fault interrupter installed.
  • There have really been incidents of pool care workers falling in with a pump that was not adequately shielded and being seriously injured or even died as a consequence of the fall in.
  • In certain cases, drawing water from the main drain and directing it down the backwash line will work; but, this method puts your pool pump at danger of losing prime and running dry in others.
  • Drilling can expose plaster and other surfaces to the elements, which can cause damage.
  • An acid wash and pool drain disclaimer may be found at the following link: Something similar to this should be used by a transparent swimming pool service firm to tell you of the hazards and difficulties that may be present.

A number of Home Depot locations in the Dallas, Texas region were available to customers.

Make sure that the pump does not run out of water.

Once the pump is forced to draw water up three or four feet above the water level in the swimming pool, it may be difficult for the pump to maintain its prime condition.

To drain the water from the pool, start the pump and let it run for several minutes.

Even if the pool is clean, it is generally best to leave the dirt and muck on the surfaces and let it to dry completely.

(3) Remove any debris that has accumulated on the ground.

If, on the other hand, the pool has extensive algae accumulation to the point that the surfaces are mostly slimy or carpeted, I would recommend leaving the material where it is to dry.

When something is very hefty, it is also tough to dispose of it.

Be sure to dilute any muriatic acid (which is often used to reduce the pH of pool water) used in the process by at least 50% with water before utilizing.

Thus, the etching process is greatly slowed, and the acid may do more to whiten and brighten the plaster without causing it to get roughened.

5.) If you don’t have an overflow line, be sure to be present when you fill the last piece.

6.) Add starter chemicals to the tap water to convert it to pool water before starting the pool operation. Retail prices for these compounds are typically about $150. A new post describing what is required should be added as soon as I can.

What Customer are Saying About ourDallas Pool Care

You may use this method to correct issues and clean your swimming pool quickly whether you need to rebalance your chemicals, decrease your TDS (total dissolved solids), or just clean up an inground pool that has not been maintained in a long time. Do not drain a pool with a fiberglass or vinyl liner. When exposed to bright sunshine, fiberglass can float and vinyl liners will normally expand. When you replace a vinyl liner, it is common for it to have crinkles in it and to no longer appear the same.

  1. Make sure you are aware of the dangers of emptying your swimming pool.
  2. If there is water saturation in the ground around the pool on rare occasions, you may experience damage due to hydrostatic pressure if the pressure release valve breaks.
  3. 2.) Make certain that the pump you are using is connected to an electrical connection that contains an appropriate ground fault interrupter (GFI).
  4. Draining a swimming pool using the backwash valve is not recommended.
  5. The expense of repairing or replacing your pool pump is typically many times greater than the cost of renting a pump.
  6. It is ideal to empty and refill a swimming pool as soon as possible once it has been drained.
  7. Something similar to this should be used by a transparent swimming pool service firm to notify you of the hazards and concerns associated.

A submersible or portable pump can be borrowed from your local hardware shop.

Specialty hardware stores may feature a greater assortment of tools and supplies.

Always check on the pump once the water level has been dropped to the height of the floor beneath the lowest step.

It may be necessary to lower the pump to a dry surface in order for it to maintain prime.

You may need to stop the pump and lower it into a dry part of the pool in order to bring it closer to the water and restore prime.

In the event that you rinse everything all the way down to the deep region near the drain, you may wind up with “goo” that is too thick to pass through the filter.

If there isn’t a lot of material, it may be beneficial to spray down the debris on the shallow end floor to the deep end in order to consolidate it and make it simpler to scoop up at the bottom.

Some of the algae has turned into a slime that has become too thick to pump out and has become exceedingly time-consuming to clean with snow shovels and buckets.

If necessary, use a power washer or an acid washer to clean the surfaces.

We also use the equivalent of a few teaspoons of dish detergent per gallon of water to act as a buffer against the acid, preventing it from permeating the plaster.

5.) Fill the container with water.

As a result, if the pool fills up, you will be there to turn it off. 6.) Add starter chemicals to the tap water to turn it to pool water. These chemicals might cost up to $150 at the retail level. I’ll attempt to write another post outlining what’s needed as soon as I can.

Dallas Pool Brands We KnowUse

When it comes to pool repairs and equipment installations in Dallas, we only employ supplies and components from the most reputable pool manufacturers.

Leave a Reply

Your email address will not be published.