Tips on Moving a Hot Water Heater Into Another Room
- Water heater relocation to another place in the home is a complex process that necessitates extensive planning and preparation on the homeowner’s part.
- For water heater installation, it is necessary to get familiar with the applicable building codes in your local area.
- The ability to reroute water lines as well as shift electrical supply lines to the new place will be required of you.
It is required by law that you employ a contractor to relocate the gas service lines if your water heater is powered by gas.Inexperienced do-it-yourselfers should avoid undertaking this job since it is complicated and perhaps dangerous.Even if you decide to transfer the water heater yourself, you should contact with a professional contractor.
Prepare the New Location
- Relocating plumbing to make room for the new placement of the water heater will necessitate the opening of walls in order to install the new pipes, fittings, and electrical lines that will be installed within the wall.
- Water heaters require venting, therefore you will need to construct a new vent pipe, which will need to exit the structure through the roof in order to function properly.
- You’ll also need to learn about roofing and flashing procedures, which you’ll need to do on your own.
Hot water heaters must be installed on elevated platforms, and seismic strapping may also be required according to municipal regulations in certain areas.Because of these new restrictions, your material and labor prices will increase.
Tips on Disconnecting Hot Water Heaters
- In order to separate the water heater from the water pipes, it is necessary to first turn off the water supply to the entire residence.
- Turn on two faucets, one set on cold and one set on hot, to drain the water pipes and the hot water heater’s tank, as seen in the following image.
- When the water has entirely drained from the water heater, it is safe to disconnect the water lines from the heater.
When disconnecting the hot water pipe, proceed with caution.Whenever you need to disconnect a hot water heater from electric power, start by shutting off the breaker that supplies electricity to it at the electrical panel and fuse box first.Close the valve on the gas line before removing the hot water heater from the gas supply.Do not attempt to repair the gas line on your own.
Tips on Moving a Hot Water Heater
- The most important thing to remember while transferring a water heater is to be careful with it and to move it in a horizontal position.
- The appliance dolly with a ratchet strap can be used; however, you must first position something between the dolly and the water heater to provide cushioning.
- When transferring the water heater, proceed with caution.
Vibrations caused by the water heater’s inside while it is in motion might cause significant harm to its interior.
Hot Water Heater Re-connecting Tips
- Make sure to pressurize and thoroughly inspect the new water pipes for leaks before putting the water heater in its final location.
- After you have connected the hot water heater to the new water lines and before you turn the water back on in the house, turn on a cold-water faucet to drain the system.
- To bleed the air out of the cold water line, turn off the cold water and then on the hot water to bleed the air out of the hot water line and vice versa.
When connecting the water heater to the new gas line, do not cut off the gas to the entire home at the same time.The result will be that when you turn the gas back on, all of the pilot lights in the home will be turned off as well.The gas flow to the water heater should always be controlled by the valve located adjacent to the water heater on the gas line.
How to Move a Hot Water Heater on Its Side
Image courtesy of didecs/iStock/Getty Images.
In This Article
- Reasons for Concern
- Instructions on How to Move a New Water Heater
- Instructions on How to Move a Used Water Heater
- It is time to replace your water heater, and the salesperson advises that you have the water heater delivered for an extra charge, or your warranty will be voided.
- The water heater’s interior components, according to some salespeople, may be harmed if the water heater is moved horizontally.
- Transporting a new water heater on its side does not affect the guarantee and may be handled with care.
Internal components are found in water heaters.Since the majority of water heaters contain glass inner linings, moving one in any position takes extra caution.It is not possible to hold several internal pieces horizontally, such as the dip tube (the plastic tube that drives water to the bottom of the tank and is positioned on the cold water input pipe).One other internal component is the anode rod, which is made of soft metallic rod that serves as a sacrificial layer to protect the tank from corrosion.
This rod is frequently installed vertically, therefore it is susceptible to breakage during transportation.Various other considerations are dependent on the sort of water heater you are relocating.The heating elements in electric water heaters must be examined, as do the pilots and controls in gas water heaters, and the firebox and controls in oil-fired water heaters must also be addressed.Water heaters with integrated refrigeration systems, such as the newer hybrid (heat pump) models, can be damaged if they are transported horizontally.
How to Move a New Water Heater
Step 1: Measure the Box
To ensure that your new water heater will fit in your car, take measurements of the available area inside the vehicle. Moving the water heater in its original manufacturing box will assist to ensure that all of the critical components are protected during the relocation. This is the moment to decide if you want it delivered or if you want to bring it yourself home.
Step 2: Move It to the Vehicle
Move the water heater to the vehicle you will be using to bring it back to your house utilizing a hand truck and an extra set of hands.
Step 3: Secure the Load
- It is critical to ensure that the water heater does not move while being transported.
- Keeping the water heater flat will be important while carrying it in a vehicle such as an SUV or a pickup truck.
- Many SUV folding seats are not totally flat when folded.
Check to see that the water heater is properly supported and laying flat, using moving blankets or boards to provide additional support.Another issue, regardless of the sort of vehicle you are driving, is to ensure that it is properly secured so that it does not move around.This is even another incentive to retain it in its original packaging.
Step 4: Choose the Right Path Home
Choose the route home that has the fewest potholes on it as your return route. Because of this, it is less likely that the tank and its interior components will be jostled.
Step 5: Remove the Water Heater From the Vehicle
When you get at your final location, prepare the hand truck and remove the water heater from the car in the same manner that you put it in. Make sure you have an additional set of hands available for this. Water heaters may be rather large and cumbersome.
Step 6: Check for Damage
Before you move too far away from the car, inspect the water heater for apparent signs of wear and tear and damage. If you’re hauling a hefty load, this might save you the trouble of making an extra trip in and out of the house.
Step 7: Put It in Position
Once you’ve brought the water heater inside, move it to the place specified by the manufacturer and your local plumbing code in order to complete the installation.
Moving a Used Water Heater
- It is necessary to follow the same processes and precautions when transferring a used water heater from another site, but you will also need to drain any remaining water from the device using a pump and hose in this situation.
- Before relocating a water heater, make sure that the gas, oil, or electricity is turned off.
- This will vary on the type of water heater you are transporting.
When working with any sort of energy, it is always advisable to use caution.
How to Relocate the Water Heater to Another Space
- When it comes to DIY projects for homeowners, relocating your water heater is one of the more challenging ones you can take on.
- In many cases, transferring your water heater is an exceedingly delicate task that may go wrong in a variety of ways due to issues like as building codes, plumbing problems, and whether your heater is electric or gas-powered.
- But with a little know-how and a little work, you should be able to move your heater to a different room in your home.
Please continue reading to discover more about how to transfer a water heater, as well as how hiring a local professional to assist you makes the process much simpler.
Get Your New Location Ready
- First and foremost, you will need to prepare the space where your water heater will be relocated before you can begin the actual relocation procedure.
- Because it necessitates a high degree of specialized expertise, this might really be one of the most time-consuming aspects of the project.
- It may be necessary to prepare the heater’s new position by constructing new pipes and electrical cables in the walls, installing a new vent pipe, and maybe erecting a platform for the heater, depending on the local building requirements.
It is critical to plan ahead of time and ensure that you have the expertise and supplies necessary to prepare this new heater installation area.
Disconnect Your Water Heater and Move It to Its New Home
- Once you are convinced that your new site is ready, it is time to get down to the job of relocating your water heater to its new position.
- Disconnecting your heater’s water and electricity supply is the first step you must do.
- Disconnection can be dangerous in some situations, therefore it’s crucial to proceed with caution during this process.
Turn off the water supply to your home, empty the water from the water heater, and then disconnect the water lines from the house.Next, switch off the circuit breaker that is associated with your heater and then disconnect the power lines—if your heater is powered by gas, it is recommended that you have a professional disconnect the gas line.After your heater has been entirely detached, carefully transport it to its new place by moving it slowly and softly.Remember to exercise utmost caution when handling water heaters since they are incredibly fragile and any stray bumps might cause harm.
Carefully Reconnect Your Heater
- After your heater has been correctly installed in its new location, you will need to complete the process of connecting the new water and electrical lines.
- The first step is to reconnect the water lines.
- Turn on a cold water faucet and wait for the water to drain out of the line.
After that, switch on a hot water faucet and wait for the water to drain out of the pipe.Final step is to connect your electric lines to the heater and then turn on the new circuit breaker that has been installed to serve your heater.If everything has gone according to plan, your water heater should be up and running in its new location.as you are aware Negotiable prices may be found on ServiceWhale for every item on the site.
The benefit of this is that you can always discover the greatest bargain for your job!
Move Your Water Heater with Help from a Plumbing Professional
- You may believe that you will be able to complete a home improvement project on your own when you first begin working on it.
- However, activities such as transferring a water heater that need specific knowledge might be too complex for even the most experienced homeowner to execute, necessitating the use of professional assistance.
- You must register with ServiceWhale in order to identify a local contractor who is capable of moving your water heater to a new site quickly and easily.
By completing a simple request process on ServiceWhale, you’ll be connected with the most competent contractors in your region, all of whom are eager to accomplish your home improvement project at a competitive price.Partner with ServiceWhale now to relocate your water heater in a timely and convenient manner.
Moving A Water Heater
- The relocation of a water heater may become necessary at some point, and there are a few elements that must be considered to ensure that the process is successful and runs smoothly.
- To begin, enlisting the assistance of a buddy might be really beneficial.
- Tank units may be quite heavy, therefore transporting one may necessitate the use of an extra pair of hands.
When it comes to electrical connections and water plumbing, there are a number of important safety factors to keep in mind.As a result, following a straightforward set of instructions can assist ensure that your water heater is successfully relocated.
Step 1 – Turn off the Power
Remove the water heater from service by turning off the breaker to the water heater. Check the unit with a volt meter to ensure there is no current flowing through it. This is really crucial to understand. A plumbing blunder can get you wet, but an electrical error can put you in danger of being electrocuted. When working with electricity, you must use tremendous caution.
Step 2 – Turn off the Water Supply and Drain
- Turn off the water supply to the tank before you begin emptying it.
- Connect a water hose to the drain valve and run it to the location where you want the water to go.
- Drain the tank water into a bathtub if at all feasible so that the tank water volume does not overflow.
Check to see that the bathtub drain is not clogged.Allowing water to drain from the tub will assist in pushing any remaining water through the water heater.
Step 3 – Disconnect Pipe
- Both the inflow pipe and the outflow pipe must be disconnected.
- Remove any connectors from the home plumbing that will be reused if the house is moved to a new location.
- Some contemporary trends call for the construction of shed assemblies near to buildings and dwellings where water heat is kept, rather than the storage of water heat in attics, basements, or closets.
Moving to a new site requires extreme caution to avoid damaging any copper tubing or connections that can be reused later on.
Step 4 – Disconnect the Electric
- Remove the cover plate that covers the electric connection on the top of the water heater.
- Remove the wire conduit connector to disclose the heater’s power connections by unscrewing it.
- Remove the set screws that hold the black, white, and ground wires in their respective positions.
Make a point of keeping these safe.It is possible that you will be able to reuse the wire from the power supply box, depending on how long it is.When disconnecting any wires, take care not to damage them.
Step 5 – Drain Remaining Water
After you’ve detached the tank from all of its cables and pipes, get a buddy to assist you in tilting the tank over and dumping the remaining water into a bucket that you’ve placed underneath the drain valve.It is important not to allow the tank to slide and cause any harm.Once the water heater has been emptied, shut off all valves and, if feasible, temporarily seal both the inlet and outlet ports to prevent any water from dripping while transporting the water heater.
Step 6 – Maneuver and Transport
Move the tank from its platform to a dolly with the assistance of a buddy in order to relocate it to a new site.
Tips to Remember
When working with electrical wiring, exercise utmost caution. Before transporting your water heater, double-check that all electricity has been turned off. Because a water heater is heavy, always enlist the aid of another person while transferring it onto a dolly.
3 Tips for Relocating Your Water Heater
In order to preserve the comfort and performance of your residential home, you must have easy access to a plentiful supply of hot water at all times.Traditional water heaters may take up a significant amount of floor space in a home.Older homes that were supplied with a water heater years after their construction may have the water heater in an inconvenient location, making it harder to make the most of the available space in your home.
It may be necessary to relocate your water heater if you find that its current placement is restricting your options when it comes to water heater installation and maintenance.Moving your water heater from one area to another isn’t as simple as it may appear at first.You must meticulously plan your relocation in order to ensure that you keep the convenience and efficiency of your water heater in the long run.1.Evaluate the condition of your current water heater.If you have committed to moving your home’s water heater, you should take advantage of the chance to assess the condition of your current water heater throughout the relocation process.
It makes no sense to waste significant time and resources moving a water heater that is nearing the end of its useful life.Residential water heaters typically have a lifespan of between 8 and 12 years, depending on the model.When completing a relocation, it is recommended that an old water heater be replaced with a new one.If you notice that your old water heater is leaking or shows symptoms of corrosion, you may want to consider upgrading to a new one.
Secondly, prepare the new location.It is possible to pick the place where you wish to install your water heater once you have decided whether or not your existing water heater is still functioning or have purchased a new unit.Homeowners who want to transfer a water heater often choose the garage as a site since it is out of the way and has enough space to accommodate the device.
The placement of your water heater must be considered in terms of both water and gas connections while hunting for a new home for your unit.It is possible that a professional will be required to reroute natural gas and water lines from the old placement of the water heater to its new location within your home, if this is the case.When calculating the expenses of relocating your water heater, remember to account for the additional expenditure of repiping.3.
- Disconnect and reconnect in the proper manner.
- You must disconnect and reconnect your water heater in a safe and efficient manner during the moving process in order to ensure that your house is safe and that your water heater is operating efficiently.
- Whenever possible, you should stop the flow of natural gas into your home by turning off the natural gas valve on the water heater.
Additionally, you should turn off the main water valve to assist you avoid any inadvertent flooding that might result in water damage to your property.Always keep unused water and gas pipes closed to avoid leaks from occurring.Pressurize your water heater once you have connected the new gas line and water pipes to it.This will ensure that the water heater is working properly.
- This procedure necessitates the removal of all air from the water lines in order for them to function properly and control the flow of water.
- Water heaters that are taking up too much room or that are interfering with your remodeling plans will need to be relocated in order to fit your demands and requirements.
- Moving a water heater appears to be an easy and uncomplicated procedure, but it may be quite dangerous if not done correctly.
- In the event that you need to relocate your water heater within your home, the assistance of a qualified plumbing specialist may be really beneficial.
- Please call Equisure Drain Cleaning if you want assistance with the safe removal of your hot water heater.
How Much Cost Is To Move Water Heater to Garage?
Typically, water heaters are kept in small utility closets in the home.Homeowners, on the other hand, may choose to relocate this plumbing fixture to the garage.This can result in the creation of more internal storage space, which can increase the value of a house.
The cost of moving a water heater into a garage can range from $150 to $10,000, depending on the situation.Customers who do not have a water line connected to their garage, who need to replace an outdated water heater, or who prefer a professional installation should expect to spend more money than other customers on their projects.Moving a water heater into a garage, on the other hand, may be rather expensive, especially if the homeowner has not already put gas and water lines into the garage.This article will cover all of the expenses connected with relocating a water heater, allowing you to better prepare financially for this home repair job.
What Costs Are Involved in Moving a Water Heater?
- The first thing that homeowners should keep in mind is that relocating a water heater to a garage is not a one-time expense. Instead, this procedure might result in a number of charges, such as the following: Replacement of a water heater
- basic tools and equipment
- water and gas lines
- and professional installation services
Each of these prospective expenses has a price range connected with it, as is only natural.Furthermore, not all homeowners will be required to budget for all of the costs indicated above.You won’t have to worry about replacing your water heater if it is relatively new or in outstanding condition, for example.
However, taking into consideration the age and quality of your present water heater is an essential first step……………………..After all, installing new gas and water pipes only to discover that your water heater is nearing the end of its useful life may be a sad experience.Have you ever had a problem with hot water in the house?Why is this so?
Water Heater Replacement
- How old is your water heater? Do you know how old it is? A big probability exists that it may not be in the best of condition if this is not the case. When properly maintained and repaired, these plumbing fixtures have an average lifespan of roughly 10 years, although they can have shorter lifespans if not properly kept and serviced. If your present water heater shows symptoms of deterioration or wear, you’ll want to remove it and replace it before you start planning and paying for a new water heater. Unfortunately, this may be a difficult task for the ordinary homeowner because the majority of water heater problems originate within the unit itself. Nonetheless, you should be on the lookout for a few indications and symptoms of a faulty water heater, such as: Low water pressure
- discolored water
- short bursts of heated water
- all of these are problems.
Contact a repair specialist as soon as possible if your water heater is leaking or producing unusual noises.If the expert is unable to repair your old water heater, he or she will be able to assist you in selecting a replacement fixture.When it comes time to replace your present water heater, you may expect to pay anywhere between $500 and $3,000 for a new fixture.
Standard water heaters are often the most economical choice, with solar and high-efficiency units being among the most expensive options available.An skilled technician may also discuss the possibility of removal and installation services in more detail.However, if you want to remove and reinstall your new (or existing) water heater without the aid of a professional, you’ll need to factor in the cost of necessary tools and moving equipment.Check out this article about Rheem Water Heater Troubleshooting.
Basic Tools and Equipment
- The following tools and equipment will be required by homeowners who intend to remove and reinstall their water heater without the assistance of a professional: Several adjustable wrenches (at least two) a flathead screwdriver a rubber hose a pipe cutter a gas line cap a dolly or hand truck a dolly or hand truck A dolly or hand truck A dolly or hand truck A dolly or hand truck A dolly or hand truck A dolly or hand truck
The overall cost of these goods ranges from around $200 to $1,000 in total.An expensive hand truck or dolly is very certain to be the most expensive item, and eliminating it from the equation reduces the cost of essential tools to around $100 or less.Fortunately, hand truck and dolly rentals are available at a number of home improvement outlets.
Naturally, fees vary based on a variety of factors, including location, availability, desired rental time, and the type of hand truck being rented.It is possible to find these wheeled mobility devices for as little as $20 a day, which is not unheard of in this industry.The majority of the items described above are likely already in the possession of the homeowner, who may only need to spend approximately $100 for moving materials, tools, and equipment.Even yet, a do-it-yourself relocation may not be appropriate for everyone.Professional installation services are also required for garages that lack water line connections (or the appropriate gas line connections).Indeed, trenching commercial-grade equipment, skilled plumbing knowledge, and technical expertise are frequently required for the installation of these lines.
Water and Gas Lines
The usual connected garage is wired, which ensures that it has access to energy at all times.Water and gas lines, on the other hand, are not often pre-installed in garages.It might be a difficulty for people who want to move their water heater from their basement to their garage.
The water line to the water heater will need to be spliced even for individuals who have washing machines in their garages.The installation of new water lines is therefore one of the most typical and substantial expenditures connected with transferring a water heater.Gas water heaters (as opposed to electric) are more expensive to relocate, so homeowners should budget between $200 and $1,000 to install a gas connection from the house to the garage.Those who have chosen an electric fixture, on the other hand, will not be required to bear this cost at all.A new water line, on the other hand, is far more expensive, generally costing upwards of $4,000.As a result, the cost of building water and gas connections might reach $4,200 or more.
It will be possible to transfer your water heater into the garage and set it up when the new lines have been connected.Despite this, connecting a water heater to a water or gas line may be a difficult and time-consuming task that requires patience.As a result, many people opt to hire professionals to perform the installation work for them.Check out this article: Why Is My Propane Heater Not Working?
Guide for Troubleshooting
Professional Installation Services
- Installing a water heater is more complicated than just attaching a few lines and plugging it into a wall outlet. In addition to adjusting water pressure levels and installing fittings, you’ll need to make sure all of your pipes and hoses are securely fastened and leak-free. The installation of a gas line by a novice can be hazardous, especially when working with gas. Therefore, professional installation services for a water heater in a garage may be the safest and most effective method of doing so. Having said that, these services are not inexpensive. Even if you are able to disconnect and relocate your water heater without the assistance of a professional, you can expect to spend a minimum of $1,000 on the installation process. Water heater installation services provided by professionals, on the other hand, are rather thorough and frequently go beyond simply connecting your fixture to a water supply line. The following services are included in many water heater installation services, for example: water heater condition inspection
- gas leak check
- drain pan installation
- and client consultation.
In addition, it is important to know that several places around the United States have rigorous construction rules, which may make it difficult for a homeowner to install a water heater without expert assistance.Using expert installation services is not only a great method to guarantee that your fixture is properly and safely connected, but it is also a cost-effective option.It’s possible that it’s the only legal choice available in your state or county.
Before embarking on a do-it-yourself relocation job, make sure to verify your local Code of Ordinances.Check see this article: Rheem Water Heater Error Codes.
How Much Does a DIY Water Heater Relocation Cost?
- It is possible for homeowners who wish to avoid the expense of professional installation services to transfer their water heater themselves. This project could cost as little as $100, but only if the following conditions are met: your garage already has a water line
- you have a pre-existing water line in your garage
- you have a pre-existing water line in your garage
- you have a pre-existing water line in your garage
- and you have a pre-existing water line in your garage.
- A gas water heater is not required because you are utilizing an electric water heater.
- You don’t need to replace your water heater
- you already have most of the equipment you’ll need to disconnect your water heater
- and you don’t have to hire a professional to do it for you.
Depending on your situation, you may just be required to hire a pipe-cutting equipment and a hand truck rental.However, this is, of course, the best-case situation.A do-it-yourself water heater relocation might also be significantly more expensive.
Whether you’re installing water or gas lines, replacing an outdated water heater, or purchasing necessary tools, you should expect to spend several thousands of dollars.
How Much Does a Professional Water Heater Relocation Cost?
Disconnecting, transferring, and reinstalling a water heater may be a time-consuming operation, especially if you’re unfamiliar with home repair chores that you can complete yourself.As a result, you may want to engage a team of specialists to do the project efficiently and effectively.It costs around $2,000 on average for professional water heater installation services.
Of course, if you don’t already have water line hookups in your garage, you’ll have to engage professionals to run a new line through it.A new water line installation can cost anywhere from $4,000 to $10,000, although the majority of homeowners should anticipate to pay around $4,000.In addition, if you decide for a gas water heater rather than an electric water heater, you’ll likely have to pay at least another $1,000 to run a gas line from the water heater to your home’s garage.As a result, professional services and line laying quickly pile up, with costs possibly reaching $7,000 or more.More information may be found at: How Much Does It Cost To Move A Furnace And Water Heater?
Conclusion
The cost of relocating a water heater might range between $150 and $10,000.. Water and gas line installs, followed by water heater replacement, are the most expensive items to factor in to your budget. Although professional water heater installation services are often priced at around $2,000, homeowners may save money by performing their own installation for far less money.
Removing the Old Water Heater
Back to the top of the page It is recommended that you read the printed instructions that came with your water heater in addition to the material on this web site. Read and observe any warning labels on the water heater, as well as the safety recommendations in the printed owner’s handbook, to limit the danger of property damage, serious injury, or death.
Step 1: Tools Required
- Hose for the garden
- hand truck or appliance dolly
- Pipe cutter, screwdriver, wrenches, and a bucket (optional) are all necessary tools.
Step 2: Turn the Water Heater OFF
Turn the knob on the gas control valve on the old water heater to the ″OFF″ position to turn it off.
Step 3: Turn the Main Gas Supply Valve OFF
- Turn the main gas supply valve OFF.
Step 4: Break the Gas Line at the Union
- Break the gas line at the union (you’ll need two wrenches for this)
- Close off the gas line
Step 5: Disconnect Gas Supply
Using a wrench, pry the gas line from the control valve of the old water heater.
Step 6: Run the Hot Water Until it’s Cool
- (this may take 10 minutes or longer).″>Open a hot water faucet and allow the hot water to run until it is cool (this may take 10 minutes or longer).″>Open a cold water faucet and allow the cold water to run until it is cool (this may take 10 minutes or longer).″>Open a hot water faucet and allow the hot water to run until it is cool (this may take 10 minutes or longer).
- WARNING! As a precaution, make sure the water is running cool before emptying the old water heater to avoid burning yourself.
Step 7: Connect a Garden Hose to Drain Valve
Connection: Attach a garden hose to the water heater’s drain valve and dispose of the other end in a drain, outside, or in a bucket to collect the water.
Step 8: Turn the Cold Water Supply OFF
- Turn the cold water supply OFF.
Step 9: Open the Drain Valve
- Drain the water from the old water heater by opening the drain valve.
- Opening a hot water faucet will assist in draining the water heater more quickly.
- Some drain valves may be opened with a handle, but others need the use of a flat blade screwdriver.
- Make sure that the water heater is totally draining
- Disconnect the garden hose
- A build-up of sediment at the bottom of the tank may jam the drain valve, making it impossible for the tank to drain correctly. Contact a competent expert for assistance if you are unable to get the tank to drain properly
Step 10: Disconnect the T&P Relief Valve Discharge Pipe
- The Temperature and Pressure (T&P) Relief Valve discharge line should be disconnected after the tank is completely depleted
- you may be able to reuse the discharge pipe, but DO NOT REUSE THE OLD T&P RELIEF VALVE. You should make use of the new T&P relief valve that came with your new water heater.
Step 11: Remove Vent Pipe
- Allow for cooling of the vent pipe. If necessary, support the vent pipe until the new water heater is installed. Once the vent pipe has cooled, remove it from the draft hood
- you may need to support it until the new water heater is installed.
Step 12: Disconnect the Water Pipes
- Prior to removing the water pipes, plan how you will connect the new water heater to the existing system. If you are using compression fittings, cut the water pipes as near as feasible to the water heater, leaving as much length as possible in the water pipes. You may always trim them to length later.″>Before removing the water pipes, plan how you will connect the new water heater to the existing system. If you are using compression fittings, cut the water pipes as near as feasible to the water heater, leaving as much length as possible in the water pipes. You can trim them to length later if necessary.
- Disconnect the cold and hot water pipes that are connected to the old water heater and set them aside. In many cases, they are joined using a threaded union that may be detached with a wrench.
Step 13: Remove the Old Water Heater
- Remove the old water heater from the room. Move the water heater with the use of a hand truck or an appliance dolly.
- WARNING: Water heaters are quite hefty. If you don’t have an appliance dolly, it’s best to have two or more people help you remove or install a water heater. Failure to do so may result in a back injury or another type of harm.
How Long Does it Take to Install/Replace a Water Heater?
June 26, 2012
Is it Time for a New Water Heater?
Dealing with plumbing problems is never a pleasant experience.When our toilets decide to back up, we don’t get to say anything.In addition, it leaks.
Don’t even get me started on leaking faucets!What is it about them that they consistently appear at the most inconvenient moments?Nonetheless, water heaters take home the prize for most irritating scenarios.Anyone up for a cold shower?Fortunately, arranging a water heater installation is a simple and straightforward procedure.There are a few considerations you’ll need to make before the water heater installation can begin.
As a result of the fact that most water heating systems endure between 10-15 years, it is likely that you are not aware of the newer, more energy-efficient systems that are available.Today’s systems, which range from 50-gallons to tankless, provide homeowners with more alternatives than ever before.Inquire with a Sinclair plumber about numerous solutions that will meet the demands of your family.Installation time, expenses, and energy consumption vary depending on the system, so being knowledgeable will ultimately save you both time and money in the long run.
So How Long Does it Take to Replace a Water Heater?
- And while we’re on the subject of time, how long does it take to finish a water heater installation? Once again, the planned time will be determined by the system you select. It will take far less time to simply replace your present water tank with a comparable system than it will to build a new tankless system, which might take some additional construction time to complete. With the exception of unavoidable obstacles, a qualified plumber should be able to have your new tank fitted and operational within 2-3 hours. In order to accommodate your hectic schedule, a trustworthy plumbing firm will arrive on time, work at a steady pace, and clean up after themselves as needed. The following is a step-by-step summary of the standard water heater replacement procedure: Take out the old water heater (45-60 minutes). While this may appear to be a simple procedure, there are various procedures that must be completed in order to assure safe removal, including disconnecting the power source, draining the tank, disconnection of the water supply lines, and the actual removal of the tank.
- Install the new heater in its proper location (approximately 30 minutes). Bringing in the new tank, extracting it from the box, and getting it into position will take some time
- connecting the system will take even more time (45-60 minutes). Once the tank has been installed, it must be linked to the water and electrical systems. If you have a gas-powered device, this may take a little longer. After the water heater installation is complete, the plumber will test it and make any necessary adjustments. Inform yourself on the basics of system maintenance and how you may make minor modifications on your own.
Scheduling an appointment with a skilled plumber will have you back in the shower in no time at all. Sinclair Heating, Cooling, Plumbing, Inc can be reached at (806) 454-9332 if you need assistance in the Lubbock region.
Model(s) Affected: All Residential & Commercial Gas Units
For a variety of reasons, basements are neither popular or practicable in various parts of the nation.As a result, many water heaters in these locations are housed in garages or other outbuildings.Installation in Residential Garagesa is defined in Section 9.1.10.1 of the National Fuel Gas Code (Z 223.1 – 2006) as follows: The installation of appliances in residential garages and in adjacent spaces that open to the garage but are not part of the living space of a dwelling unit shall be such that all burners and burner ignition devices are located not less than 18 in.
(460mm) above the floor, unless the appliance is listed as Flammable Vapor Ignition Resistant.It is necessary to position or safeguard such equipment in such a way that it is not exposed to physical harm by a moving vehicle.Appliances installed in a separate, enclosed space with access only from the outside of the garage are permitted to be installed at floor level if the required combustion air is obtained from the outside of the garage.d.Appliances installed in a separate, enclosed space with access only from the outside of the garage are prohibited from being installed at floor level.Our home gas versions, which are supported by two-inch steel legs, raise the primary burner orifice (on the stamped steel burner) to a height of 412 inches above the ground.
The primary burner orifice on the cast iron burner is positioned 5″ above the floor.Burner pilots (also known as ″burner ignition devices″) are located higher up on the burner than the primary burner orifices on both of these styles of burners.The water heater stand that is currently available is 14″ in height.By adding the aforementioned burner measurements to the height of the platform, it is possible to meet the total code requirement of 18″ in height.
There are two sizes of heavy gauge steel water heater stand kits available: small and large.– 18″ square x 14″ high for water heaters with a diameter of 18″ and a capacity of 40 gallons or less.– 24″ square x 14″ high for water heaters with a diameter of 24″ and a capacity of 75 gallons or less.– Please keep in mind that a 40 gallon heater that weighs around 125 pounds when empty rises in weight by an additional 333 pounds when loaded (8.33 pounds per gallon x 40 gallons.) The stand must be strong enough to support the 458 lb total weight of the machine.
How Much Does a Water Heater Weigh? (37 Examples)
- Is it time for you to relocate a water heater, but you’re not sure how much weight it will be? Alternatively, you may be considering purchasing one and want to know if you would be able to carry it yourself. The question is: how much does a water heater weigh, no matter what the circumstances are? In order to discover out, I looked at 37 various tank-style, tankless, and under-the-sink refrigerator types. Here’s what I took out from the experience: Tank-style water heaters weigh an average of 150 pounds when they are empty, although the weight varies depending on the size. Tank-style water heaters weigh an average of 2.6 pounds per gallon of capacity on average. Tankless water heaters are substantially lighter than traditional water heaters, weighing on average 27 pounds. In addition, the average weight of an under-the-sink water heater is 32 pounds. The average 50-gallon tank can carry up to 417 pounds of water, due to the fact that water weighs 8.34 pounds per gallon of water. When you combine it with the weight of the tank, you have one hefty unit. In the following sections, I’ll show you 37 different types of common water heaters and tell you how much they weigh when they’re empty and how much they weigh when they’re full with water. I also go through some of the other elements that influence the weight of water heaters, as well as some pointers on how to transfer them safely. To move around this article, click on the links below: The actual weight of 37 water heaters
- the factors that influence the weight of a water heater
- moving tips for a hot water heater
- and final thoughts
Actual Weight of 37 Water Heaters
The table below illustrates the actual weights of 37 commonly used water heaters by type and capacity, which should help you get a better grasp on how much different water heaters weigh.Please keep in mind that GPM stands for Gallons Per Minute.It is a measurement of the volume of water that a tankless water heater can heat in a given length of time.
To see the complete chart, scroll or swipe horizontally across it.
| Brand/Model | Weight Empty | Weight Full | Capacity | Type |
|---|---|---|---|---|
| RheemXE40M06ST45U1 | 106 pounds | 440 pounds | 40 Gallons | Tank |
| RheemXE50M06ST45U1 | 132 pounds | 549 pounds | 50 Gallons | Tank |
| RheemXE38S06ST45U1 | 95 pounds | 412 pounds | 38 Gallons | Tank |
| RheemXE30S06ST45U1 | 95 pounds | 345 pounds | 30 Gallons | Tank |
| WestinghouseWEC080C2X045 | 151 pounds | 818 pounds | 80 Gallons | Tank |
| RheemMHD85245 | 139 pounds | 848 pounds | 85 Gallons | Tank |
| RheemMHD75245 | 122 pounds | 748 pounds | 75 Gallons | Tank |
| RichmondS80U-1 | 192 pounds | 859 pounds | 80 Gallons | Tank |
| A.O. Smith Signature Premier | 302 pounds | 969 pounds | 80 Gallons | Tank |
| WestinghouseWEC080C3W165 | 151 pounds | 818 pounds | 80 Gallons | Tank |
| WestinghouseWEC115C2X055 | 224 pounds | 1183 pounds | 115 Gallons | Tank |
| WestinghouseWER052C2X045N | 118 pounds | 552 pounds | 52 Gallons | Tank |
| WestinghouseWER040C2X055N | 104 pounds | 438 pounds | 40 Gallons | Tank |
| WestinghouseWEC100C3W135 | 151 pounds | 985 pounds | 100 Gallons | Tank |
| MarathonMHD105245 | 152 pounds | 1028 pounds | 105 Gallons | Tank |
| MarathonMR40245 | 91 pounds | 425 pounds | 40 Gallons | Tank |
| CampluxME60N | 26 pounds | 76 pounds | 6 Gallons | Tank |
| RheemXG29T06EN30U1 | 110 Pounds | 352 pounds | 29 Gallons | Tank |
| RheemGHE80SS-130A | 600 pounds | 1267 pounds | 80 Gallons | Tank |
| Sure ComfortSCG40T03ST34U1 | 125 pounds | 459 pounds | 40 Gallons | Tank |
| Richmond6G50-60F3 | 150 pounds | 567 pounds | 50 Gallons | Tank |
| John WoodJW6F307 | 172 pounds | 422 pounds | 30 Gallons | Tank |
| WestinghouseWGR060NG076 | 170 pounds | 670 pounds | 60 Gallons | Tank |
| RheemECOH200DVLN-2 | 82 pounds | N/A | 9.5 GPM | Tankless |
| RinnaiV65iN | 45.6 pounds | N/A | 6.5 GPM | Tankless |
| RinnaiRL94iN | 46.3 pounds | N/A | 9.8 GPM | Tankless |
| RheemECOH200DVRHLP | 85 pounds | N/A | 11 GPM | Tankless |
| Eccotempi12-NG | 29 pounds | N/A | 4 GPM | Tankless |
| RheemRETEX-13 | 7 pounds | N/A | 2.54 GPM | Tankless |
| EcoSmartECO 18 | 11 pounds | N/A | 3.51 GPM | Tankless |
| Black + DeckerBD-27HD | 12.17 pounds | N/A | 5.4 GPM | Tankless |
| Titan ModelN-120 | 8 pounds | N/A | 4 GPM | Tankless |
| Richmond6EP15-1 | 54 pounds | 179 pounds | 15 Gallons | Under the Sink |
| RheemXE06P06PU20U0 | 37 pounds | 87 pounds | 6 Gallons | Under the Sink |
| Bosch8733954924 | 17.3 pounds | 51 pounds | 4 Gallons | Under the Sink |
| Stiebel EltronSHC 4 | 19.8 pounds | 53 pounds | 4 Gallons | Under the Sink |
| Stiebel EltronSHC 6 | 26.5 pounds | 77 pounds | 6 Gallons | Under the sink |
Factors Impacting Water Heater Weight
A few things influence the total weight of your water heater, including the kind of water heater, the size of the tank, and whether or not the tank is full. Let’s take a closer look at each of them.
Water Heater Type
Tank and tankless water heaters are the two most common types of water heaters.Unlike other types of water heaters, tank-style water heaters contain a tank that reserves hot water so that it is available whenever you need it.Tankless water heaters, also known as on-demand water heaters, do not store hot water in a large tank and instead heat water as it is needed.
As an alternative, when you turn on a shower or faucet, cold water is forced into the device, which then heats it.Tankless water heaters have additional benefit over traditional tank-style heaters, aside from the energy and cost reductions.They are significantly lighter.Tankless water heaters weigh an average of 27 pounds, whereas tank-style water heaters weigh an average of 150 pounds.
Size of Tank
- Because of the size of the tank, the weight of tank-style water heaters varies greatly. Single-family houses often have water heater tanks that hold between 40 and 80 gallons of water. When the tank is completely drained, you should anticipate it to weigh something like this: forty gallon water heaters typically weigh 106 pounds, fifty gallon water heaters typically weigh 140 pounds, and eighty gallon water heaters often weigh 200 pounds. 40 gallon water heaters are the most common size.
Generally speaking, tankless water heaters with a greater GPM (gallons per minute) capacity are larger in size and weigh more than those with a lower GPM capacity. A tankless heater with a flow rate of 11 GPM from Rheem weighs 85 pounds, but our 2.5 GPM one weighs only 7 pounds. a
Water in Tank
To be sure, the tank gets substantially heavier if there is any water present in it. One gallon of water weighs little more than eight pounds, so if you want to relocate your water heater, I recommend that you empty the tank first.
Tips for Moving a Hot Water Heater
- Water heaters, particularly tank-style ones, are difficult to transport because of their weight, clunkiness, and awkwardness. Consider the following suggestions before you begin. First and foremost, shut down the electricity, gas (if applicable), and water supply. Following that, if you have a walkout basement, connect a hose to the water heater’s drain and drain the tank fully outdoors. If your tank is not in a walkout basement, you can discharge it into a drain or a sump pump to prevent flooding. As an alternative, you can drain the water slowly into a bucket by using a skimmer or a strainer. Finally, unhook the gas and water lines from the tank and move it out of the way to a place where you can safely lift it. Other suggestions to bear in mind are as follows: Before you move anything, make a plan. What is the direction of the train? And how are you planning on getting it there? Inspect your surroundings to ensure that the road is clear and that you have enough space to pass through doorways and staircases.
- If the item is too heavy to lift, a dolly should be used.
- Inquire for assistance. Attempting to move it alone might be risky because it may end in harm.
- If you are not comfortable with the idea of disconnecting the water heater, you should see a plumber.
If you want further guidance, this instructional video will lead you through the process of relocating a water heater.
Final Thoughts
Tank-style water heaters are quite heavy, and the larger the tank, the greater the weight of the water heater in general.Weights vary from as low as 90 pounds to as much as 600 pounds for them.On average, most models weigh roughly 2.6 pounds per gallon of capacity, according to the manufacturer.
And that is the weight of the empty container.When the weight of the water is taken into consideration, these units might weigh several hundred pounds or more.Tankless water heaters are significantly lighter and simpler to move than traditional tank water heaters.They weigh an average of only 27 pounds, however the weight fluctuates depending on the size of the animal.There are some versions that weigh up to 85 pounds, and there are others that weigh less than 10 pounds.To move your water heater, be sure to disconnect the electricity, natural gas and water sources as well as empty the tank before you do so.
Always enlist assistance when moving water heaters, and utilize appliance dollies and measuring tape to ensure that the transfer will go as smoothly as possible.If you require more assistance or do not feel confident, you should see a plumber.
Can You Transport a Water Heater in a Car?
- Every homeowner will eventually find themselves in the position of having to replace their water heater. Some people will hire a plumber, while others will opt to change it themselves at their leisure. If you intend to install the water heater yourself, you will need to ensure that it is transported securely from the store to your home before starting the installation. Most likely, you’re wondering whether or not the water heater will fit in your car or if you’ll need to borrow a friend’s truck or trailer to complete the project. So, will a water heater be able to fit in my vehicle? If you have a mid-sized or bigger vehicle, you should be able to move a tankless water heater up to and including a small 30-gallon water heater without difficulty. For some of the bigger 40- or 50-gallon water heaters, you’ll need an SUV or a pickup vehicle to transport them. Do you require the services of a Licensed Plumber? We can assist you! In your location, you may get a free estimate from plumbers that are top-rated, vetted, and licensed. In order to prevent damage to the glass liner within the water heater, the water heater must be installed vertically (if at all feasible) on the floor. If you have no choice but to turn the water heater on its side, make sure it is well cushioned and drive slowly to decrease the likelihood of damage to the water heater. Keep in mind that an automobile, such as a four-door sedan, will most likely not be large enough to accommodate a water heater. Even if the water heater is placed upright in the backseat or trunk of these smaller vehicles, it will not be able to withstand the weight of the appliance. The majority of the time, you will need a larger truck to move the water heater safely and securely. While you don’t need need a large vehicle to transport a water heater, a truck is an excellent option for moving water heaters. Even a smaller SUV, such as a RAV 4, that has the ability to fold the back seats for more space, may be used to transport smaller water heaters. Let’s take this approach to thinking about it. For example, if you’re thinking about acquiring a water heater such as the well regarded and popular A.O. Smith Signature 40-Gallon Tall 6-year Limited 4500-Watt Double Element Electric Water Heater, you’ll need at least 61.25 inches of space in your trunk to accommodate it. It will fit perfectly in the Nissan Rogue (with the seats folded down), which has 68.9 inches of interior room. Be sure to measure the precise dimensions of your desired water heater before relocating or acquiring one for your home. You can determine whether or not self-hauling is a possibility based on the particular specs of the water heater and the available trunk space in your vehicle. At Lowes.com, I looked at a number of A.O. Smith models as well as a Rinnai Tankless model. Water heaters by A.O.Smith stand 60.5 inches tall, while A.O.Smith Short water heaters stand 49.75 inches tall
- A.O.Smith Lowboy water heaters stand 32 inches tall
- A.O.Smith Tall 50 gallon water heaters stand 60.75 inches tall
- A.O.Smith Hybrid 50 gallon water heaters stand 63 inches tall
- and Rinnai tankless water heaters stand 26.4 inches tall.
A 40-gallon tall water heater must be transported standing up, therefore you will need somewhat more than 5 feet of clearance in general.The Short and Lowboy versions stand at roughly 4’2″ and 2’8″ in height, depending on the model.If you discover that your water heater can fit inside your vehicle, you will need to take further measures.
You can cause damage to your water heater’s glass lining (resulting in a break that would leave it inoperable), the internal dip tube, or even the anode rod if you do not take good care of your water heater.These components are essential for a well running water heater, thus taking care to reduce the likelihood of a breakdown is highly recommended.
How Can You Avoid Damage When Moving a Water Heater?
The most safe technique of carrying a water heater is in an upright, vertical posture with the heater firmly secured in place.In part, this is due to the fact that there will be no bumps in the road that may cause the glass lining to shatter or the anode rod to bend or break.It is possible to strap someone in a vertical posture in a truck or, in certain cases, a large-sized SUV.
The following steps should be followed if you’re transferring your water heater in a smaller vehicle and have to lay it on its side: It is critical to have enough of padding around your water heater.Always make sure that there is enough of padding around your water heater to prevent it from being damaged.Between the floor of your automobile and the water heater, you may use blankets, towels, and other thick items to keep the temperature stable.Consequently, there will be less chance of fragile parts within the water heater breaking or bending, leaving it inoperable.The water heater should never be allowed to rest on the control panel.Check to make sure that the water heater isn’t resting on the controls of the system.
Water heaters are commonly packaged in a horizontal configuration, and following the packaging instructions is critical to ensuring a safe and damage-free transport of a water heater.Remove the anode rod and dip tube if you want to save money.It is possible for the anode rod and dip tube to bend and break rather readily in a water heater, making them two of the most vulnerable components.It is recommended that you remove these two sections from your water heater before carrying them away to reduce the possibility of twisting and breaking.
A smooth drive will limit the likelihood of the water heater bending or breaking.Try to steer clear of potholes, bumps, and other potentially hazardous road conditions that might cause your car to bounce up and down with a great deal of force while you are driving.A broken portion of the water heater may result from exerting too much power on it when you are doing this.
That being said, make every effort to ensure that the roads you’re driving on are as smooth as possible.When removing your water heater from your vehicle, proceed with caution.When someone tries to relocate their water heater by themselves, there are several mishaps that might occur.The simple act of dropping the water heater (which might be difficult to handle) or simply not handling it with care can result in a broken or bent water heater.
- When transporting water heaters from one site to another, a dolly is highly useful.
- Always make sure that the dolly is well-padded.
How to Move a Water Heater – Step by Step
We’re going to walk you through a straightforward, step-by-step procedure for transporting your water heater safely-even in your car.
- To begin, make certain that the gas or electricity has been turned off. (Please note that this will vary depending on whether you have a gas or an electric water heater
- thus, familiarize yourself with your product before attempting to relocate.)
- Although it is important to drain the water, always use caution when doing so because the water will be hot
- If you are working with a gas water heater, you will need to detach the vent pipe from the draft hood at this point, making sure that the pilot light is totally out before continuing. After that, you may disconnect the gas line by capping the end of it.
- You have the option to remove the dip tube and anode rod at this stage if you so want. Even though it isn’t essential, if you are concerned about them being twisted or damaged during the relocation, you can remove them entirely to avoid a potential problem.
- Remove the pipe from the system
- After that, you may move the water heater onto the dolly and secure it in place without tightening it too firmly. Inspect the controls to ensure that they are pointing upward.
- With the water heater safely transported to the automobile, it may be carefully placed inside the vehicle. When transferring the water heater, use extreme caution to prevent causing any harm to the unit. Be prepared with enough cushioning in your automobile and a space accessible in your vehicle.
In Closing
If you find yourself in the position of having to replace your water heater but do not require the use of a special truck or other equipment, you will be pleased to hear that you may do it using your own car, as long as it is large enough to accommodate the water heater you choose to purchase.When relocating the water heater, you must, however, use extreme caution to avoid damaging it.When transporting the water heater, make sure there is enough of padding around it, that you avoid bumps and potholes in the road, and that you handle it with care when bringing it out of the car and into the house.
DISCLAIMER: The information provided on HomeInspectionInsider.com is not intended to be professional guidance.Before beginning any job, you should contact with a competent expert and verify that all necessary permits have been obtained.It is owned and operated by Hubert Miles who is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by placing advertisements and links on their websites that direct traffic to