How To Lift A Water Heater By Yourself?

How To Lift A Water Heater (Quickly & Easily!)

  • Everything has a shelf life of some sort.
  • You will ultimately need to replace your water heater no matter how many years you are able to squeeze out of it.
  • For the vast majority of us, this means upgrading from a pretty large tank to a new tank or tankless water heater, depending on our needs.
  • However, how do you get the old water heater out of the way so that you can put in the new water heater?

It is critical to exercise caution, as it is all too simple to injure oneself along the route.Sure, you could lift it on your own, but why make things more difficult than they have to be?The most effective method is to utilize straps and, preferably, a hand cart to transport the items.What Services Do You Require for Water Heater Repair?Get free, no-obligation quotations from professional contractors in your area.LOCAL CONTRACTORS CAN BE FOUND

How to Lift a Water Heater

  • In terms of weight, an empty water heater would generally weigh between 125 and 175 pounds when compared to another appliance of same size.
  • Naturally, this may vary based on the size of the tank in question, but this is typically what you will have to deal with.
  • The difficulty does not necessarily lie in moving it, but rather in doing it in a safe manner.
  • There are simply too many tales out there about people who attempted to move their water heater tank on their own and ended up in serious trouble.

Step 1: Get a Friend

  • Even if you don’t want to go overboard with your removal procedure and don’t want to do it alone, enlisting the help of a friend or family member is never a terrible idea.
  • You may even arrange ahead of time so that you know you will have assistance when the time comes to remove the items.
  • This manner, one person can hold either end of the water heater, and the two of you can easily transport it out of the house.
  • An operation involving two people is almost always the best option when dealing with stairwells.

As a result, you won’t have to bear the entire weight of the staircase and manage it yourself anymore.

Step 2: Just Lift It

  • The use of this method is not recommended for a number of different reasons.
  • The most apparent is that the water heater tank is heavy, and if you slip and fall, it might come crashing down on you and cause injury.
  • If you’re feeling brave or don’t want to put in the effort required by another approach, this one can be a good option for you.
  • The only snag is the way the house is laid out.

If you live in a one-story home, it may be quite simple to just remove the old water heater by hand from the house.However, in multi-story homes, where the water heater is most often located in the basement, navigating the stairwell can be quite hazardous.If there are any steps involved, it is strongly advised that you do not attempt to remove the water heater by hand and on your own at this time.There are more effective and efficient ways to do the task at hand.

Step 3: Hand Truck

  • This procedure and the next one are nearly identical, with one significant variation.
  • An extra hand cart may be really useful for a variety of tasks, including transporting an old water heater, which can be particularly difficult.
  • If you do not currently have a hand cart, you might consider purchasing one to add to your inventory.
  • A hand cart may be used to angle the bottom panel below the water heater, allowing it to be tipped back towards you.

This stage might be tough if you don’t take the right safety precautions, so go slowly and steadily to avoid having the water heater hurl itself back at you.Straps are usually not necessary for single-story dwellings, although they are recommended.You should be able to place the water heater onto your hand cart and roll it through the front door with a little effort and care.It is only when there are a set of stairs involved that things turn a little dicey.

Step 4: Hand Truck and Straps

  • This is the single most successful way for removing an old water heater tank on your own that you will find..
  • The hand truck is an important component of the equation.
  • It alleviates virtually all of the strain associated with lifting, making it simple to carry even the heaviest of objects from one location to another.
  • Having stated that, there is a problem with stability.

This is where the straps come in.The ideal hand truck kit should have steel strap supports to keep the truck in place.After that, you’ll loop the strap around the tank and weave it through the supports, then weave it through the handles of the hand truck.The goal here is to ensure that the water heater rests solidly on the hand truck throughout transportation.When maneuvering staircases, this is the best option since it eliminates the possibility of the water heater tank slipping off of the hand truck while in use.It is highly suggested that a hand truck and straps be utilized for one-person moves whenever possible.

What to Do With Your Old Water Heater

  • You have made the choice to replace your old water heater with a new one.
  • The old unit has been removed and will be placed to the side while the new unit is being set up.
  • Everything is in place and ready to go to work as soon as possible.
  • Nevertheless, what are you going to do with the old water heater tank?

When it comes to the removal and disposal of your old water heater, you have a variety of alternatives.Just a handful of the more feasible alternatives are shown here.

Donate the Old Water Heater

  • It’s possible that an update is required since the old equipment is just that: old.
  • It might also be caused by an increase in demand that the old water heater is unable to handle.
  • As long as your old water heater is in good working order and in good condition, you can donate it to charity.
  • Call your local donation facility, such as a Habitat Restore, and inquire as to whether they take water heaters for recycling.

The good news is that it comes in twos.The first advantage is that you now have a means to get rid of that old water heater.Two, you may claim it as a charitable contribution that is tax deductible.The only bad news is that you’ll have to deliver it to the recipients yourself.If you don’t have any support or a vehicle large enough to transfer it, you may need to find an other solution or contact a friend who can assist you with the transportation.

Recycle the Old Water Heater

  • It’s possible that your old water heater isn’t in a condition that allows it to be donated.
  • Either that, or you come to the conclusion that donating the item is simply too much of a nuisance for you.
  • So, what are you going to do with it now?
  • Consider repurposing your old water heater.

Steel is used in the construction of the great majority of water heater tanks.Not only that, but they are also embellished with brass and copper.Your local recycling center will most likely offer you the current market cost for such materials, but be aware that there may be a disposal charge associated with the transaction.Some recycling centers may even be able to organize a collection for you, depending on your location.Be cautious to check with the recycling center before simply dropping off your scrap metal, since state rules governing scrap metal might be complicated.What Services Do You Require for Water Heater Repair?

Get free, no-obligation quotations from professional contractors in your area.LOCAL CONTRACTORS CAN BE FOUND

Trash It

  • Depending on your municipality, there may be certain days set out for bulk garbage pickup.
  • Larger objects such as tables, chairs, and even water heaters may be set up as a result of the increased space.
  • Give your local garbage collection business a call to check whether they provide this service.
  • Some localities even provide curbside collection for the purpose of recycling or refurbishing the device.

In some cases, you may be required to pay an additional fee, therefore it is critical that you contact ahead beforehand.Nonetheless, this is a quick and efficient method of getting rid of that old equipment.

Take it to a Landfill

  • If your town does not provide a pickup service and you do not intend to donate it, you can still dispose of it at a landfill.
  • However, you should not simply throw it out in your neighborhood dumpster.
  • To dispose of a water heater, contact your local landfill.
  • Most landfills can take water heaters for disposal, although they will likely demand a fee.

Some landfills may even offer a recycling program, but it’s best to check ahead of time to prevent any unpleasant surprises later on.

Related Articles

  • Is a 50-gallon water heater sufficient for a family of four people?
  • Using a 40-gallon water heater, how many showers are you able to take?

Ryan Womeldorf is an American actor and director. Ryan Womeldorf has been writing professionally for more than a decade. He enjoys writing about building, plumbing, and other home-related issues on his blog. Ryan also enjoys hockey and has been a lifetime supporter of the Buffalo Sabres.

Recently Published

  • What Color Garage Door Goes With a Gray House?
  • is a useful resource.
  • With a gray house, what color garage door should you use?
  • The most effective approach to increase your property’s curb appeal is rather simple: make sure your home is well-maintained.

It is actually rather simple to paint a gray exterior, which is wonderful news for those who have a gray exterior.link to Utility Knife versus Box Cutter: What’s the Difference, What’s the Use, and What’s the Type

How to Lift Water Heater into Pan

  • An under-sink drain pan is highly recommended if you have a water heater or tankless water heater in your house.
  • Most of the time, water heaters in basements are located on top of a floor drain, which can capture any leaks that occur.
  • Those who live on higher floors should have a water heater pan fitted before any severe damage may be done to the tank’s inside walls.
  • A drip pan that has been properly placed will be attached to a drain pipe and will capture any leaks from your water heater, no matter how serious they get.

It provides an additional layer of protection against water damage to your floor, walls, or any other area of your valuable home.You have two options when it comes to installing a water heater pan: either call a plumber or install the water heater pan yourself.There are a few different methods for lifting a water heater into a pan on your own.One option is the typical bear embrace – with some additional hands, of course – but this may result in back problems if you do so too forcefully.Alternatively, you may get a hand truck that is designed exclusively for lifting water heaters.Continue reading to discover how to hoist a water heater into a drain pan with a step-by-step instruction and answers to some frequently asked questions, whether you’re replacing a water heater or simply installing a new drain pan.

How to Lift Water Heater into Pan: Step-by-Step Guide 

1. Turn off any water line that leads to and from your water heater

Check to see that the cold water supply and hot water line are both turned off. Activate the hot water faucet to ensure that the water is turned off. In order to be extra careful, you might disconnect all the lines till you’re finished with the project.

2. Turn off the main water supply

If you have an electric water heater, you must first switch it off before you begin any lifting or transferring. Using this method, you may ensure that there is no water pressure while working.

3. Drain all the water from the storage tank

To completely drain the tank, turn on the relief valve. Due to the lengthy nature of the process, it may be tempting to attempt to move the water tank while it is still full; nevertheless, lifting the tank before emptying all of the water is risky. A hot water storage tank is really heavy, so don’t underestimate the task and end up breaking your back in the process.

4. Enlist some assistance

In addition to alleviating any worry you may be feeling if this is your first time, having a second person to assist you makes everything much more secure!

5. With your assistant, bear hug and lift the water tank together

It should not be difficult to transport an empty tank. However, if your water heater tank is larger than the usual, you might consider investing in an equipment that will aid you in transporting a water heater like a professional plumber!

6. Lift the water heater with a hand truck

  • It is easier to lift and lower water heaters from platforms, as well as move them in and out of pans, if you have a hand truck and strap kit available.
  • It is particularly built to cradle water heaters, and it comes with a strap kit that allows you to easily hold and carry even the heaviest water heaters!
  • It may be a little pricey, but it is well worth the purchase, and your back will thank you for it!

 7. Place drain pan under it

Make certain that the discharge hole is pointing in the same direction as your drain pipes.

8. Lower the heater into the pan

Whatever technique you use, make sure to lower the water heater tank into the drip pan drain before starting to reconnect the water lines.

9. Firmly close the pressure relief valve and the drain valve

Using pipe dope, which is a sealer, you may assist in making PVC pipe joints leak-proof before proceeding with the installation. Here’s a hot plumbing tip: before you begin, lay a paper towel over all of your connections, valves, and heat pump to check for leaks before you continue.

See also:  How Many Amps For Hot Water Heater?

10. Reconnect the supply lines

If you have an electrical heater, you may now re-energize it by reconnecting it to the main power source. If you have a gas water heater, you may now relight the burner without risking a fire.

11. Securely attach drain pipe to the drain pan’s discharge pipe

This pipe will divert any water from the pan into the drain line, preventing an overflow from occurring. To guarantee that the tubing is the right length, use a tubing cutter.

Frequently Asked Questions

How do you put a pan under a water heater?

  • Before you can place a drain pan beneath it, you must first completely empty the water heater.
  • Because flexible hoses are used to link the tank to the water supply pipes and because copper is not used, it is possible to slowly elevate the tank in order to slip the pan underneath it.
  • In the case of a large water heater, or in the case of wires that are not flexible, it may be necessary to hire expert assistance to install a water heater drain pan.
  • Alternatively, if difficulties recur, an expansion tank may be considered.

Can you transport water heater laying down?

It is possible to transfer a hot water heater by lying it on its side. Be aware that if the item is not moved properly while in this position, the metal shell may be damaged, and the glass lining may break as a result.

How do you pick up a water heater?

  • Prior to removing the water heater from the stand, be certain that it is completely empty and that it is not linked to the house plumbing, as well as any gas or electrical lines.
  • Take hold of the water connections on top of the heater and tilt it towards you as you go backwards until the water runs out completely.
  • You’ll be able to lift it off the stand and place it on a hand truck to transfer it after the stand becomes loose.
  • However, skilled plumbers do not recommend bearhug the water heater to pick it up since it has the potential to inflict significant body harm over time.

Why is there water in pan under water heater?

  • Water in the pan under a hot water heater is most often the result of a leak in the system.
  • Check for leaks at the vent pipe fittings and, if necessary, tighten the cold water pipe connections to ensure that they are secure.
  • Consider the possibility that leaking may be caused by corrosion and silt accumulation within the tank.
  • If this is the case, you may need to turn on the shut-off valve and replace the drain valve and anode rod, among other things.

It should be noted that the same holds true for a washing machine pan.

Lifting water heaters.

  • I believe I’ll need to borrow the tool that Master Plumber Mark has been using to raise water heaters onto their stands.
  • Normally, I can move a water heater onto a stand by tying a belt around it and lifting it from there.
  • Stairs, on the other hand, are a very different story.
  • Maybe it’s because I’m growing a little older, but I had a strong feeling yesterday that Mark had a superior solution.

If you look closely at the image below, you’ll notice a pillar on the left side.While a result, I may have been unable to get the water heater into the desired position, and as I was raising it I fell backwards, clutching the water heater to my chest, and we both crashed on the garage’s concrete floor.It was actually rather amusing.My second try went a lot better, thanks to a helping hand resting on the top of the heater while I raised again.Okay, Mark, please give us your recommendations on what we should put on the trucks.

There aren’t many water heater supports or earthquake straps to be found in this area.

  • Well,Terry I hope you were not injured in any way.
  • It is possible to pull a groin muscle and have serious consequences if you are not careful.
  • Pam isn’t going to like it if you take yourself out of commission for a couple months.
  • Groin pulls take a long time to recover.

not to mention the fact that it will aggravate your back for a long time.I’ve got theMULE.sitting in the back of my pickup.It was 500 dollars on Craigslist when I found it.It was practically brand new when I got it, and I keep the battery disconnected on it so that I can recharge it every few weeks regardless of whether I need to.Last week, I utilized it to raise an 80-gallon electric tank by myself.In addition, my brother-in-law and I completed a 75-gallon gas tank together a few months ago, which was a breeze.

When moving a 75-gallon heater into position, it is advisable to have assistance since the heater becomes top heavy.However, we managed to pull the thing into the hole and lower it onto the stand without putting any strain on either of us.Dan was impressed because he wanted us to manhandle the situation in some manner.

Put the heater on the platform, wheel it into position, and elevate it to a height of approximately an inch or two above the stand, if necessary.You must secure the wheels in order for it not to move on you.The heater is then moved from the Mule to the heater stand by simply sliding it off the Mule.It is sometimes preferable to use a washing machine hose to wrap around the heater and regulate the operation more effectively.Moreover, it is often necessary to have someone hold onto the handles so that the heater does not move on you when you are transferring it from one location to another.I’m not quite satisfied with how well my mule’s locking mechanism functions.

therefore I’ve had to rely on the male client to keep it in position because on occasion I’ve had to use a grinding wheel to remove those metal poles in order to have a better angle on the process in order for the legs of the mule to get in close.If they complain about it being removed, I just do not complete the task.I got a terrific bargain on this, and the price has risen significantly since I purchased it in 2014.

I believe they have surpassed 2300 presently.I also have an Escelara Stair cat in my vehicle, which has proven to be a lifesaver for all of the heaters in basements and on the second story of residential buildings.This was three years ago, and the stair cat cost $2200, but it paid for itself within the first week of use.The most recent edit was made on November 17, 2018.

There aren’t many water heater supports or earthquake straps to be found in this area. What is the name of this brand? That appears to be a straightforward and straightforward solution to the problem.

Hello, Terry. That is a very attractive piece of equipment. However, I don’t see your sticker on it; did you forget to place your calling card on the heater, as well?

  • Hello, Terry.
  • That is a very attractive piece of equipment.
  • However, I don’t see your sticker on it; did you forget to place your calling card on the heater, as well?
  • I’m in desperate need of stickers.

They’re in everyone else’s possession.I went to the chiropractor on Monday for my three-month checkup, and there was no need for an adjustment.I did receive one in March of this year.It seemed to be effective for me.It was 1989 when I first found it.The fact that I was falling backwards with a water heater dropping on me didn’t seem to disturb me either.

Funny.However, I will need to include a lifting tool.This is getting out of hand.

I’ve thrown in a few more for good measure. Some of this makes me a little uncomfortable. What it’s like to wear a belt. Now that I’ve seen someone else do it, it appears to be somewhat uncomfortable.

The first one I was on the verge of purchasing just for fun. He is located in the plumbing zone and sells them to anyone who is interested in purchasing one. It’s acceptable, and it’s less than 200 dollars.

What is the name of this brand? That appears to be a straightforward and straightforward solution to the problem. It’s a Wesco product that was produced in the United States. The difficulty is that it is far heavier than any of the warmers and so takes up valuable space in the back of a vehicle.

  • It’s a Wesco product that was produced in the United States.
  • The difficulty is that it is far heavier than any of the warmers and so takes up valuable space in the back of a vehicle.
  • I believe you’ll need a larger truck in that case.
  • I rented a box truck and placed both of these items onto it, strapping them to the sides of the vehicle.

My Stair kitty weights 115 lbs, so it is a substantial piece of equipment.However, you are not allowed to pick it up and move it; rather, you are supposed to roll it at an angle so that you do not feel the weight.Do you have any clue how much that one will set you back?..

It has been my experience that utilizing perforated straps and short sheet metal screws, I have been able to secure the stand to the bottom of the heater. Then simply raise it to its upright position. Lately, I’ve been just discarding stands.

  • I believe you’ll need a larger truck in that case.
  • I rented a box truck and placed both of these items onto it, strapping them to the sides of the vehicle.
  • My Stair kitty weights 115 lbs, so it is a substantial piece of equipment.
  • However, you are not allowed to pick it up and move it; rather, you are supposed to roll it at an angle so that you do not feel the weight.

Do you have any clue how much that one is going to cost?The one we have is about 15 years old and weights 125 pounds, according to our estimates.You can feel the weight being shifted into the back of the vehicle!Looking on the internet right now, they offer a variety of sizes, with prices starting at around $650 and rising from there.

  • It has been my experience that utilizing perforated straps and short sheet metal screws, I have been able to secure the stand to the bottom of the heater.
  • Then simply raise it to its upright position.
  • Lately, I’ve been just discarding stands.
  • It is theoretically possible to place fvir heaters on the floor with the new models, but if I were to lower one, I would be certain to receive a visit from some unpleasant home inspector down the road who would demand that the unit be brought to code height.

I don’t need to get into an argument or get into a fight with someone half my age.

Yes, that does happen every now and again. Mark, I believe you should include one in this section as well.

  • If you know how, feel free to put some money in my tip jar.
  • I don’t expect anyone to give anything, but it’s just for fun.
  • It’s just for fun.
  • Another lift cart that you might be interested in is shown below.

Another plumber recently purchased one and informed me of his purchase today.It appears to be of high quality and is likely to be reasonably priced.This appears to be a nice deal, and if my mule were to fail me, I would most likely purchase it.It is not inexpensive to repair.They’re asking for $1200 for it.same as though it were composed of silver or platinum

2 Methods to Lift a Water Heater Without Hurting Yourself

  • Is it feasible to lift a water heater without causing yourself any injury?
  • Yes, it is correct!
  • In reality, this essay will demonstrate not one, but two different approaches to completing the task at hand.
  • Here are two methods for raising a water heater.

Water heaters may be several hundred pounds in weight.Therefore, it is quite crucial that you discover a secure manner to hoist yours as well.I’ll go into further depth about these two approaches below.

Method 1 – Using a Ramp and a Dolly

  • What you have been doing recently in terms of training will not prepare you for the physical demands of lifting a water heater in the future. And we’ve all had back pain by lifting something we shouldn’t have been lifting in the first place. So, let’s skip the weeks of anguish and the expensive trips to the chiropractor by performing the job correctly the first time. You may achieve your objective to transfer a water heater without injuring your back by using the first way listed below. This is an excellent strategy that just necessitates the use of a few simple instruments. The following is a comprehensive list of all of the supplies you will require to complete the project. You Will Require Garden hose, adjustable wrench, ramp, and dolly are all included.

Once you’ve gathered your kit, come to step one and meet me there.

Step 1 Drain the Water

The water within your water heater will add hundreds of pounds of unneeded weight to the machine, causing it to fail prematurely. It is therefore preferable to drain the water before attempting to transfer it. In order to empty your water heater, perform the following steps.

  1. A garden hose should be connected to the drain valve of the water heater.
  2. Run the other end of the hose outside your home or into a floor drain to drain the water.
  3. Drain the water heater by opening the drain valve. When the water stops gushing out of the hose, it is said to be empty.

Step 2 Remove Any Inputs

Before you can transfer your water heater, you’ll need to disconnect any of the heater’s connections from the outside world. This includes everything that is associated with it. The following steps should be followed in order to remove the inputs from your water heater.

  1. Disconnect the flexible water heater pipes from the rest of the house’s plumbing. This job may be completed with the help of an adjustable wrench.
  2. Gas should be turned off at both the water heater and at the gas manifold.
  3. Remove any electrical connections that may have been made
  4. Removing the exhaust and placing it to one side is recommended.
See also:  What Is The Best Temperature For A Tankless Water Heater?

Step 3 Walk the Heater Onto a Ramp

Now that all of the preliminary work has been completed, you may begin the process of relocating your water heater. Keep in mind that you should never raise the water heater with the back of your hand. Allow gravity to carry it to the location where you require it. Start by walking the water heater onto the ramp as shown in this illustration.

  1. A ramp should be built right next to the water heater.
  2. Take hold of the water heater by the water connections that are located on top of it. As you take a step backward, tilt it towards you. Tilt the water heater so that it is facing the ramp. Observe how it slides off the stand and onto the slope
  3. Take it leisurely as you walk down the ramp and onto the ground floor.
  • Okay, but what if you’re relocating a water heater from the bottom to the top?
  • Then you may utilize the same procedure as before.
  • Create a lining for the ramp at the base of the water heater this time.
  • Using the water hookups as levers, you can then lift it up the ramp and onto the platform.

I understand that certain things are best experienced rather than articulated.So why not have a look at this tutorial video to learn how to move your water heater up and down a ramp.

Step 4 Move the Heater Onto a Dolly

You will now require the use of a dolly or a hand cart. Make sure you have a friend with you for this phase.

  1. Carry the dolly all the way to the bottom of the water heater.
  2. Hold the water heater in place by the water connections that are located on top of it. It may be leaned to one side, with a dolly being pushed below it by a companion.
  3. Make use of the dolly to move the water heater to anywhere you require it to be.

Method 2 – Using a Handle and a Dolly

  • Okay, so here’s an alternative way for raising your water heater that you may try. This approach is particularly useful for heaters that are so heavy that they cannot be moved up and down a ramp by hand. Rather of a handle for the heater, you will see instructions on how to move it onto a dolly this time. Here’s a list of everything you’ll need for this procedure, organized by category. You Will Require Toolkit includes: garden hose, adjustable wrench, 34-inch elbow, 3-hole tee with three holes, 12-inch pipe, 2 galvanized steel bars, 8 screws and 2 blocks of wood.
  • Drill with a powerful motor
  • Dolly

Step 1 Drain the Water

To begin, you must first drain the water from your water heater and turn it off. You will be able to move more freely as a result of this. Follow the steps below to empty yours.

  1. A garden hose should be connected to the drain valve of the water heater.
  2. Run the other end of the house outside of your home or into a floor drain to complete the circuit.
  3. Drain the water heater by opening the drain valve. When the water stops gushing out of the hose, it is said to be empty.

Step 2 Remove Any Inputs

Before you can transfer your water heater, you’ll need to disconnect any of the heater’s connections from the outside world. This includes everything that is associated with it. The following steps should be followed in order to remove the inputs from your water heater.

  1. Disconnect the flexible water heater pipes from the rest of the house’s plumbing. This job may be completed with the help of an adjustable wrench.
  2. Gas should be turned off at both the water heater and at the gas manifold.
  3. Remove any electrical connections that may have been made
  4. Removing the exhaust and placing it to one side is recommended.

Step 3 Create a Handle to Lift the Heater

Making a solid handle that will aid you in raising the heater will be the following step. We will connect the handle to the two water connections on the top of your water heater, which will be installed by us. Listed here is everything you’ll need to complete the handle.

  1. A 34-inch elbow should be attached to the hot water side of the water connection.
  2. Attach a 34 inch tee with three holes to the cold water side of the water connection to the cold water side of the water connection
  3. To link the two pieces together, thread a 12 inch pipe through the tee and into the elbow. Make use of the wrench to tighten and align the connection in the appropriate manner. In order to determine the length of pipe required, you must first determine the size of your water heater.

Step 4 Slide Two Steel Bars Under the Handle

You are almost ready to begin moving the water tank now that you have completed the preparation of the handle. For the following stage, you’ll need to get your two galvanized steel bars out of storage. In addition, you’ll need two blocks of wood, eight screws, and a power drill. What you’ll need to do is prepare your screws and wood in advance, as shown in the diagram.

  1. Drill the screws into the board in a square pattern, just partly through the wood. In total, four screws should be used for each block of wood. The screws should be driven into the backboard behind the water heater using an electric drill. On either side of the heater, one block should be placed. Place the blocks at the same width as the inner side of the handle
  2. the blocks should be spaced evenly apart.
  3. Slide the bars beneath the handle to make it easier to use. There are two bars on either side of the handle. The bars will serve as a lever, which you will operate. Ideally, both bars should be resting on a block of wood.

Step 5 Squat to Lift It

Make certain that you have someone to assist you before performing this stage on your own. Once you’ve raised the heater, you’ll need someone to help you slip the dolly underneath it. With your bars in position on top of the blocks of wood, crouch down and push up on them to pull the water heater up to the appropriate height.

Step 6 Slide a Dolly Under the Heater

If possible, slip a dolly beneath the water heater while it’s being lifted. It is possible to roll the heater anywhere you want it by utilizing the dolly.

Conclusion

  • You’re attempting to raise a water heater, right?
  • Then accomplishing this without injuring yourself does not have to be an insurmountable challenge.
  • I’m confident that the two approaches described in this post have demonstrated what you can do to move yours without putting your back in danger.
  • Has this article been of assistance to you?

If that’s the case, why not have a look at some of our other articles and free resources?You may even join up for our email list if you wanted to.Have a wonderful day!-Craig

How can I install a drain pan under my existing water heater?

  • The Water Heater (WH) will need to be drained and completely disconnected from all piping, wiring, and venting, as well as any other applicable components.
  • Slowly and carefully tip and roll the bottom edge of the WH off of its brick stand until it is free of the stand.
  • I say slowly and gently because there is an Anode Rod and a Dip tube within that are just joined at the top, and while they are rather sturdy, it is important not to cause any damage to them.
  • After being tilted, refrain from yanking and slamming the WH back down.

After that, you’ll need to figure out how high you want the new stand to be.You should have at least 1/8″ drop or slope per foot of pipe from the pan to your building’s departure point, floor drain, or sump basin, according to the manufacturer’s specifications.If you’re in close proximity to the pan’s pipe outflow position, your bricks may be fine; nonetheless, you must consider for the thickness of the external wall.You may now place your new stand on the ground and roll the bottom of the WH onto it.If a ramp is required, a 2×4 or broader length of wood is generally sufficient for the job.Then you’ll want to tilt the WH so that you can slide your pan underneath the tipped side without piping.

At this point, all you have to do is repeat the edge roll in order to get the WH into the pan.Once you’ve done so, gently rock or jiggle the WH to get it centered and aligned with the pan and the pan’s drain to your satisfaction.Finally, reconnect the WH and the piping from your new pan.

Shark-Bite style fittings are ideal for use with WH’s.

How to Light a Water Heater

  • Article to be downloaded article to be downloaded You may see cold water flowing from your hot water faucet if you reside in a home that has a natural gas water heater.
  • This is a good indication that your pilot light has gone out.
  • It is not necessary to hire a professional in most circumstances; you will have hot water again in a matter of hours if the pilot is re-ignited correctly.
  • While having your water heater’s instruction manual on hand is a good idea, it is not fully required because most gas water heaters need a similar process for relighting the pilot light, as described in this article.
  • 1 Make that the pilot light is working properly.
  • You will most likely need to remove a tiny panel at the bottom of the tank, known as an access panel, in order to determine whether or not the pilot light is truly turned off.
  • If you do not see a little flame flickering, this indicates that your pilot light has been turned off.
  • Depending on your water heater model, it is conceivable that your panel is not detachable and that you must observe your pilot light via a transparent window.

In this instance, if you are unable to see a flame burning through the glass, your pilot light is not working properly.

  • 2 Check to see whether there is any gas leaking. Never attempt to restart your pilot light if there is gas leaking from your water heater, as this is highly harmful to both you and your property. Instead, call 911 immediately. To check for leaks before attempting to relight the pilot, perform a basic smell test on the cylinder. Standing near to your water heater, sniff the air to see if you can notice any strange aromas. After that, get down on your knees and smell around any valves on the front and sides of the tank. Naturally, natural gas has no odor. To make it noticeable to humans, gas companies add an ingredient known as mercaptan to the mixture. The smell of leaking gas is similar to that of sulfur or rotting eggs.
  • If you detect the presence of gas in either of these locations (even if it is a faint odor), do not attempt to relight the pilot. Remove yourself from the vicinity of the water heater and contact your gas provider immediately
  • they will advise you on what to do next.
  • Also, keep an ear out for hissing sounds near the water heater, which might indicate a gas leak.
  1. Promotional material
  2. 3 Instructions may be found on the inside of the door panel of your water heater. Detailed instructions for your specific water heater model may be available here, and following them may assist you in the process of relighting the pilot for your unique water heater. Advertisement
  1. Step 1: Lower the temperature control setting to the lowest possible setting. This is normally placed on the front of a box that may be found on the outside of the water heater.
  2. 2Find the regulator valve on the water heater. When this valve is turned off, the pilot burner beneath the hot water tank will not operate. This valve is normally found in a similar location as the temperature control, however it is most likely positioned on the top of the box.
  3. 3Turn the knob to the ″Off″ position. Wait 10 minutes after turning off the knob before proceeding to ensure that any remaining gas from the tank has cleared the air before continuing. The most important thing is to be safe!
  4. 4
  5. Determine the type of water heater that you have installed. Gas hot water heaters are often classified into two categories: ″new″ and ″ancient.″ Traditional heaters will require you to relight the pilot light with your own flame, however newer design tanks are fitted with a pilot light igniter built into the tank. However, while the specific appearance of the buttons on modern design tanks may vary, many of them include a red igniter button that is located a few inches away from the temperature and regulator valves.
  • 5 Gather any lighting items that may be required.
  • You will need to obtain a long-reach ″wand″ lighter or fireplace matches to relight the pilot on an older design water heater.
  • Avoid attempting to relight a pilot with a conventional matchstick or a small cigarette lighter since doing so will force you to place your fingers in a small, tight position too near to the open flame, putting you at risk of being burnt.

6Travel to the location of the pilot. The pilot is positioned at the end of the little silver tube that comes out of the control valve and is connected to the control valve. It’s possible that you’ll need to use a flashlight to see clearly in this location. Advertisement

See also:  How To Reset Ao Smith Gas Water Heater?

1 Turn the gas valve to the ″Pilot″ position and press the button on the valve. It is necessary to do this in order to initiate the flow of gas into the tube that supplies the pilot light. Find a red control button near the gas valve on your water heater if the gas valve on your water heater does not press down properly. Keep your finger on this button.

  • 2 Light the pilot burner with a match. The pilot gas valve or the red button will be held down with one hand while the other hand will be used to swiftly light the pilot. To use this button, make sure you have a new model water tank with a built-in ignition switch installed. You should be able to hear a clicking sound until the pilot burner comes on. If you have an old-fashioned heater, ignite the pilot burner with a wand lighter or match and wait a few minutes.
  • Because you will be using one hand to push the valve/red button while using the other hand to ignite the pilot, you may require the assistance of another person to carry a flashlight for you if you require additional lighting. Make an effort to get assistance in advance so that you do not go halfway through a procedure only to be forced to halt because you are unable to see what you are doing
  1. 1 Minute after the pilot light has been ignited, keep the gas valve or control button down by pressing it down one more time. This will heat the thermocouple, which is a sensor that turns off the gas when the pilot is not lit.
  2. 4Release the valve knob/control button to complete the process. After a minute, open the valve and press the control button to check if the pilot light is still on.
  3. 5Remove the access panels and replace them. When checking to see if the pilot light is still lit, replace the access panel (if you had to remove it first) to ensure that no flames escape into your home.
  4. 6Restart the main burner. Turn the main gas valve back to the ″On″ position and set the temperature control to the appropriate temperature. The main burner under the tank should be turned on and the water in the tank should begin to heat. Caution: When turning the knob to ″on,″ be careful to keep your head away from the burner area.
  5. 7Set the thermostat to the appropriate temperature. Remember not to heat the water to a boiling point, since you might scald your hands or body accidently when washing or bathing. The Consumer Product Safety Commission recommends a temperature of 49 degrees Celsius (120 degrees Fahrenheit). Advertisement
  • Question Add a new question Question How can I start a gas heater that is more recent in design? Look up your model number and get in touch with the manufacturer for more detailed information. For the most part, the only difference between a current heater and these instructions is that newer units include an electronic igniter (you simply press a button and a spark is produced) for lighting the pilot. What do I name the gadget that I use to ignite the pilot’s engine when I press a button on it? It’s referred to as a ″spark igniter.″
  • Concerning the Question What should I do if the pilot light on my water heater keeps flickering on and off? It is likely that you will have to replace it. You can also get in touch with a supplier or even the business that made your water heater.
  • Concerning the Question What should I do if the pilot light won’t remain lit for whatever reason? The most likely cause of your problem is that your thermocouple has to be repaired or replaced. A pilot light is a short copper tube that connects your water heater’s controls to the pilot light and has an end that sticks into the flame. Whenever the pilot light heats up the tip, it creates electricity that is detected by the control box, which allows it to determine that the pilot light is on. A new one is simple to install, and you can pick one up at any home improvement, plumbing supply, or hardware shop. Take your old one with you so that you may acquire the right measurement. A little bit longer is OK, but not typically much shorter
  • Question When I press the pilot button, how long should I hold it down before pressing the little red ignitor button beneath it? It takes around 5 seconds. Question: Can you turn it back on and change the temperature? So, what should I do if the pilot light won’t turn on for whatever reason? Continue to try while keeping an eye out for any signs that there is gas coming through (usually by smell). The likelihood is that the regulator is faulty and that it will need to be replaced. This is also something that may be accomplished by oneself.

Inquire about something There are 200 characters remaining. Include your email address so that you may be notified when this question has been resolved. Advertisement submissions are welcome.

Video

  • If this procedure does not provide results, check to see that the pilot light’s base is not filthy or blocked. If it is, clean it well and repeat the process after 10-15 minutes. You may also try holding the valve/control button for an additional 30-45 seconds after the pilot light has been ignited.
  • If this technique does not work, it might be due to a lack of gas pressure or a defective gas valve. If you are unable to ignite the water heater despite many efforts, contact an appliance repair person, a plumber, or your gas provider.
  • You may have a faulty thermocouple if the pilot light does not come back on after being re-lit or if it goes out soon after being re-lit. It is possible to see the thermocouple in the pilot light flame region because it extends from the temperature control into the flame area.
  • They are reasonably priced, and you can do the installation yourself.
  • Thank you for submitting a suggestion for consideration! Advertisement If you detect the scent of gas anywhere in your home, contact your gas provider right once. Even a ″little smidgeon of gasoline″ is too much.
  • Do not re-open the gas valve until you have completed the replacement of the access panels. It is possible that a flame will come out of the water heater if this is done.

Advertisement

About This Article

  • Summary of the ArticleXTo switch on an electric water heater, begin by setting the temperature control to the lowest setting and turning the gas regulator valve to the ″Off″ position.
  • Then, by adjusting the gas valve to the ″Pilot″ position and pressing down on it, you may begin to pump gas into the system.
  • After that, press the red ignitor button, which is located near the gas valve, to ignite the pilot burner.
  • Hold down the pilot button for 1 minute longer than you think it should be and check to see whether the pilot is lit.

If it isn’t, go back and repeat the process until it is If this is the case, flip the gas valve back to the ″On″ position and adjust the temperature to your liking.Continue reading for helpful hints on how to prepare for and light your water heater.Did you find this overview to be helpful?The writers of this page have together authored a page that has been read 389,186 times.

The heat is on: How to stay hydrated, save on your home’s cooling bill and protect your pets

  • Drink lots of water and avoid intense activity if you want to stay healthy in the high heat of the summer.
  • If you live in a hot climate, keep your house cool and preserve electricity.
  • How to keep your canine companion cool throughout the heat
  • In the United States, heat-related illnesses are increasing in frequency and intensity as heat waves become more common and intense.
  • When temperatures rise to extreme levels, typically above 100 degrees, there is a risk of cardiovascular and respiratory disorders, as well as heatstroke in the most severe instances.
  • American’s can expect a number of heat waves that will break records in the summers to come as a result of climate change, much like the sweltering heat that has gripped the western United States for weeks, resulting in daily records being broken or tied across Arizona, California, Nevada, and even into the interior parts of the Pacific Northwest in Oregon and Washington.a Here’s guide on how to keep you and your loved ones safe on hot days, whether they have two legs or four.

How do I stay healthy and hydrated?

  • The most important step in protecting the body from heat-related disease is to maintain adequate hydration.
  • According to the Mayo Clinic, the average adult requires 1112 to 15112 glasses of fluids every day.
  • Water is the ideal choice, but other beverages that contain electrolytes can also be beneficial, as long as you avoid drinks that include excessive amounts of alcohol, caffeine, or sugar.
  • Smaller meals more frequently can assist in maintaining electrolyte levels and replenishing salt lost via perspiration, according to the American Red Cross.

High protein diets, according to the World Health Organization, should be avoided at all costs.″Water, water, and more water would be the order of the day when it comes to hydration.As for eating, it should be ‘light’ food, nothing substantial, so things like fruit and sandwiches are OK ″Tyler Roys, a senior meteorologist at AccuWeather, spoke to USA TODAY about the forecast.What is a heat dome, and how does it affect the weather?

What should I avoid doing during a heat wave?

  • According to the Centers for Disease Control and Prevention in the United States, it’s advised to restrict rigorous activity and high-energy outdoor activities as much as possible throughout the summer.
  • If you have to work outside, the World Health Organization recommends doing it during the coolest portion of the day, between 4 and 7 a.m.
  • Electric fans may be a terrific source of relaxation – as long as the temperature does not exceed 95 degrees.
  • Scientific American reports that fans do nothing more than circulate heat in already hot and dry air and, rather than lowering body temperature, they can actually raise the risk of physical stresses, according to the publication.

In fact, try to reduce the usage of any electrical gadgets, as well as the use of artificial lighting, to a bare minimum in order to prevent generating extra heat.

What can I do to keep my home’s temperature low without my bills being too high?

  • When it’s hot outside, our air conditioners have to work much harder to keep us cool inside – and this may add up to a significant increase in our energy bills.
  • According to the National Weather Service, it is equally critical to preserve electricity during a heat wave in order to avoid widespread power disruptions.
  • During the night and early morning, when temperatures are at their lowest, open windows and shutters to allow air to circulate throughout your home.
  • As soon as the temperature rises to its noon high, close all doors and fill any gaps in the insulation with as much as you possibly can.

Shades and blinds should be drawn to keep the light at bay.It might also be beneficial to apply light reflectors to the windows to improve visibility.If you want to create one at home, try wrapping cardboard with aluminum foil.Global warming: The heat wave in the Western Hemisphere would have been ″absolutely unthinkable″ if not for climate change.

How can I keep cool if I don’t have air conditioning?

  • When you can’t get away from the heat, there are a few things you may do to naturally cool your body.
  • Dress in clothes that is loose-fitting and light in color, composed of natural materials.
  • When sleeping, use linen sheets that are lightweight and restrict the number of pillows and cushions to a bare minimum to avoid heat from collecting.
  • One alternative is to use ice packs or cool, moist cloths to the face and torso to relieve the pain.

Cold showers and foot baths are another excellent ways to bring your body temperature down to an acceptable level.If you’re outside, hunt for sources of shade – or make your own from scratch.Wide-brimmed hats can be used to deflect the sun’s rays and protect your face from the sun.The Federal Emergency Management Agency (FEMA) suggests that people seek air conditioning in public places like as libraries, shopping malls, and community centers.During the warmest hours of the day, the Red Cross recommends that you stay with a neighbor who has air conditioning to keep cool.

How do I keep my pets safe?

  • Leave your animals in the car at any time, and the same is true for youngsters.
  • When driving, temperatures increase quickly, and even with the air conditioner on or a window cracked, the heat can be harmful to your pet.
  • Pets, like people, require lots of fluids to be healthy.
  • Put a couple ice cubes in Fido’s water dish, or give your pet a cold body wrap to keep him cool.

In the backyard, make sure your pet has plenty of shade — but not in an area that would restrict air movement, such as a doghouse.Pets should be kept cool and away from the heat and pavement, as the pavement will be several degrees hotter than the surrounding air, according to Roys.It is also recommended by the Humane Society that pet owners check humidity levels since animals rely on panting to remove body heat and are unable to cool themselves when there is a high concentration of moisture in the air.

Leave a Reply

Your email address will not be published.