How To Install A Gas Water Heater

How to Install a Gas Water Heater

You may save money on your utility expenses by installing a new gas water heater. How to do it is demonstrated in our video and step-by-step tutorial. Please keep in mind that product pricing, availability, and item numbers may differ from market to market.

Before You Begin

Before committing to a full replacement, conduct a brief maintenance inspection to determine the root cause or the necessity for a new water heater. If you follow the methods outlined below and find that replacement is required, make sure to verify your local building codes before proceeding to confirm that you are in compliance. And, if you’re still not sure, consult with a professional.

Check Water Pressure

The water pressure in your house is critical for all of the equipment that use water. A decrease in pressure reduces the stress placed on plumbing systems and helps to increase the lifespan of appliances and fixtures. When it comes to pressure monitoring, you might want to think about using an inline pressure gauge.

Add an Expansion Tank

To install an expansion tank, follow the instructions outlined below.

Removing the Old Gas Water Heater

Installing a new gas water heater is simple if you follow these procedures. Exercise caution when unpacking and unwrapping your new water heater to avoid causing damage to it. Water heaters are heavy; while transporting the appliance, enlist the assistance of a friend, an appliance dolly, and/or a hand truck.

Preventing Scalds

Even with the temperature gauge set at 120 degrees, the risk of scalds remains a possibility. Children, the elderly, and individuals with delicate skin are particularly at risk of developing skin cancer. Consider adding thermostatic mixing valves to save people from being hurt. Installed at the point of use faucet, fixture, or appliance, a thermostatic mixing valve regulates both the volume and temperature of water by connecting to both the hot and cold water supply lines at the same location.

DIY Water Heater Installation

Time A busy day of work Complexity IntermediateCost$101–250

Introduction

When your water heater begins to leak, you must act quickly to have it repaired or replaced. We’ll teach you how to set up your own natural gas water heater in less than a day’s time. Even if you do not require a new water heater at this time, it is likely that you will require one within the next few years. Water heaters typically have a lifespan of seven to fifteen years. If yours is beginning to show signs of wear, this post is also for you. If you’re familiar with basic equipment and have a little expertise soldering copper, replacing a water heater shouldn’t be too tough.

Tools Required

  • Water and gas piping
  • Discharge pipe
  • Fittings
  • Pipe thread compound
  • Pressure relief valve
  • Solder. Ventilation pipe and connections
  • Pressure relief valve.

Getting Started Installing Your New Hot Water Tank

In this example, we’re swapping out a natural gas water heater for an electric water heater. The processes for replacing a propane water heater are identical to those for replacing an electric water heater, and the steps for replacing both are comparable. In any event, when it comes to arranging a water heater replacement, it’s best to be cautious. Call your local department of inspections and inquire as to whether or not you require a permit. Also, be certain that your work is checked by a plumbing or electrical inspector.

Plumbers normally charge between $45 and $65 per hour and can complete the installation of a water heater in a day or as little as 6-8 hours.

Gas water heaters with particular venting systems are also available, although they are more costly. However, because they are more difficult to install, we will not be covering them in this article.

Water Heater Parts and Breakdown

  • Fire pipe, cold water shutoff valve, draft diverter, temperature and pressure relief valve, overflow pipe, hot water outlet, anticorrosion anode rod, dip tube, elements, insulation, drain valve, thermostat or control valve, burner, thermocouple, gas supply valve, and more.

When to get a new water heater

When the tank of your water heater leaks, your water heater is out of commission. An indication that your water heater needs to be replaced is a gradual drop beneath the unit, which commonly manifests itself as a trail of discolored water. This indicates that the steel tank has corroded through and will be unable to be repaired. Other symptoms, such as little or no hot water, are typically indicative of other water heater repair issues that may be resolved by you. If you notice a drop, make a plan to get the water heater replaced as soon as possible.

  • New water heaters are sent with detailed installation instructions as well as several cautions to ensure that the gas, electrical, and other connections are handled properly.
  • However, you should be aware that you will be dealing with natural gas, propane, or electricity, all of which are potentially harmful.
  • And, after you’re finished, get your work examined.
  • You should explain to your local plumbing inspector how you want to install your new connections, including the sorts of materials you intend to use.

Figure A: Gas Water Heater Details

Mr. Fix-It-Up-For-The-Family See the Additional Information section at the end of this article for instructions on how to print this image.

Figure B: Connections for Steel and Plastic Pipe

Mr. Fix-It-Up-For-The-Family Water supply pipes in many residences are made of galvanized steel or polyvinyl chloride (CPVC). Replaceable galvanized steel pipes are quite difficult to come by. Using our photo series, we propose that you return the pipes to their original tees and screw on a plastic-lined galvanized nipple before finishing the connections with copper. Plastic tubing should be kept at least 6 inches away from the vent and tank due to the possibility of heat accumulation. Using a specific connection, you may make the transition from plastic to copper.

Flexible copper connectors are less difficult to install than solid copper connectors, which is especially important when the existing pipes and tank inlets do not match up.

If yours does, take extra care not to pinch or kink them when handling them.

Project step-by-step (12)

Turn off the gas to the water heater by twisting the shutdown valve a quarter turn away from the water heater. When the handle is turned off, it should be at a straight angle to the pipe. Also, turn off the main water supply and drain the pipes by opening a tap on the lowest floor of the building. Step No. 2

Drain the water in the tank

Connect a garden hose to the drain valve and use it to drain the water that has accumulated in the tank.

The water will be boiling hot, so proceed with caution! With a pair of wrenches, disconnect the gas line at the neighboring union and remove the pipe from the gas control valve with a pipe wrench to complete the task.

Sign Up For Our Newsletter

Complete your do-it-yourself tasks like an expert! Become a subscriber to our newsletter! Do It Right the First Time, and Do It Yourself! Step number three.

Cut off the water lines

The vent pipe should be moved to the side once it has been unscrewed from the vent hood. After that, using a tube cutter, cut the hot and cold water lines. For galvanized pipe, remove the unions and, if you have them, remove the nuts on the flexible connections as well. Move the old water heater to the side of the room. Step number four.

Attach the relief valve

Teflon tape should be used to seal the threads of the new temperature and pressure relief valve (three turns). With a pipe wrench, tighten it inside the tank until it is completely sealed. Glue a copper discharge pipe to the wall (see Fig. A for routing details). Step number five.

Attach pipe assemblies

Solder fresh copper adapters to 6-in. lengths of 3/4-in. copper pipe and screw the assemblies into the hot water outlet and cold water inlet ports on the top of the tank’s tank’s tank’s tank. Make use of short, plastic-lined nipples to protect your pipes from galvanic corrosion, especially if you have hard water or if they are required by your local building standards. Step 6: Organize your thoughts and feelings about the situation.

Attach the water lines

Slide the new water heater into position, recut or lengthen the old tubing to connect it to the new, and solder the tubing together using copper slip couplings to complete the installation. If the tubing does not line up properly, use pairs of 45-degree elbows to adjust the alignment of the lines. Step 7 – Organize your time and resources.

Reattach the vent

Reconnect the vent if necessary. Place it securely over the draft hood and secure it with three 3/8-in. No. 6 sheet metal screws to hold it in place. Prepare the holes by drilling them beforehand. Before turning at the first elbow, the vent should rise at least 12 inches vertically from the floor. In this eighth step, you will learn how to use a comma to separate the words “and” and “and not.”

Use two wrenches to attach the gas line

Reconnect the gas line if necessary. Pipe joint compound should be applied to the threaded ends before screwing the first nipple into the gas valve. To minimize straining the valve, use two pipe wrenches at the same time. Reassemble the remaining nipples, concluding with the union at the end of the process (Photo 2). Then, in order to fill the tank, perform these four steps: To check for leaks, perform the following steps: (1) cut off the main water valve; (2) re-connect the water at the main shutoff; (3) open the cold-water valve on the water heater (but do not close it); and (4) turn on a nearby hot-water faucet until water flows out.

Check for backdrafting

The majority of water heaters rely on a natural airflow to carry combustion emissions up the chimney and out of the building. If the draft does not operate, the fumes, which may contain lethal carbon monoxide, will be released into your home and cause you to become sick. Check the draft when you’ve finished installing everything. Close all of your external doors and windows, and put on the exhaust fans in your kitchen and bathroom. Continue to run a hot water faucet until you hear the gas burner in your water heater come to life.

Ideally, the smoke should be drawn upward through the vent pipe. If the smoke does not draw, this indicates that the burner’s fumes are not escaping. Turn off the gas supply to the water heater and contact a certified plumber to diagnose and remedy the problem. Step number ten.

Check for leaks

When it comes to drawing combustion gases up the chimney, the vast majority of water heaters rely on natural airflow. The gases, which may contain lethal carbon monoxide, will stream out into your home if the draft isn’t working correctly. Check the draft when you’ve finished with your setup. Make sure all outside doors and windows are closed, as well as the exhaust fans in your kitchen and bathroom. Continue to run a hot water faucet until you hear the gas burner in your water heater come on.

The smoke should be pulled upwards through the vent pipe to be expelled.

Turn off the gas supply to the water heater and contact a certified plumber to diagnose and remedy the problem.

In this final step, you will learn about

Light the pilot light

The pilot light should be turned on in accordance with the manufacturer’s instructions. (When using an electric water heater, turn on the electricity at the main panel after your work has been checked by the electrical inspector). Once you’ve finished, adjust the temperature to 120 degrees Fahrenheit according to the installation instructions. The pilot light in the new water heater should be lit, then the temperature setting should be adjusted.

Installation Details for Electric Water Heaters

At your main electrical panel, turn off all power to your water heater, then turn it back on. Then follow the same draining methods as for a gas water heater. As soon as the water heater has been drained, separate the electrical wires from the screw terminals under the access panel, which is normally situated towards the top of the water heater. To handle all of the electrical wiring, you should engage an electrician if you don’t have any prior knowledge with it. When it comes to wiring the new water heater, follow the manufacturer’s instructions.

  • x 4-in.
  • metal electrical box on the wall or ceiling near the water heater, route the old wires to the box, and then run a new length of armored cable or electrical conduit to the water heater to complete the installation.
  • The circuit should also have a shutdown switch that is visible from the vicinity of the water heater.
  • You’ll almost certainly require a permit.
  • Aluminum wire needs specific care and handling.

If you have aluminum wire, you should choose a qualified professional who is experienced in working with it. This wiring is a dull gray color, rather than the drab orange color that is characteristic of copper wiring. ‘Step 12’ is the final step in the process.

How to Dispose of a Water Heater

In this video lesson, Jeff Gorton, an editor at The Family Handyman, will show you how to remove and dispose of a water heater in the proper manner. He will also demonstrate a simple method of transporting a water heater out of your home, even if you are working on your own.

These tips will make your work go faster and easier:

  • To avoid modifying the length of your water, gas, or electrical lines, take note of the height of your existing water heater and get a new one that is the same height
  • On older water heaters, the drain valve (Photo 2) frequently becomes clogged. Please be patient if the water drains slowly. WARNING: The temperature is really high! TIP: Turn off your water heater two hours before you want to use it to enable the water to cool. Water heaters are around 150 pounds in weight. When you’re moving the old one out and wheeling the new one in, you’ll need a strong partner or a dolly to assist you. Ordinarily, garbage collection agencies charge approximately $25 to remove the old one. Before you begin, go to a plumbing supply or hardware store, or a home center, and purchase the equipment and materials seen below. Check the sizes of the water supply pipes (the majority will be 3/4 in., as shown in our photographs) and purchase the fittings that are the proper size. If you have everything you need, you should be able to complete the work in four to six hours (provided there are no major problems!). This safety device, which limits tank pressure and prevents it from exploding, is located in the tank’s pressure relief valve assembly (Photo 4). It is necessary to include a fresh one with each installation. The discharge pipe must be kept clear of impediments in order for the valve to function correctly (see Fig. A). Use 3/4-in. plastic-lined nipples (about $2 each
  • Photo 5 and Fig. A) to attach other metals, mainly copper tubing to the steel tank, in areas where the water is highly mineralized or where it is needed by municipal laws. This has the effect of slowing rusting. In order to avoid heating the tank itself during soldering, solder the copper fittings before screwing them to the tank (Photo 5)
  • Slip couplings should be used to link the existing and new water lines (Photo 6). (Photo 6). They do not have an internal stop, in contrast to normal couplings. Alternatively, you may slip them on, align the copper tubing, then slide them back and center them over the junction
  • However, the new inlets and outlets on the tank don’t always line up with the old supply lines, and vice versa. If required, solder in a pair of 45-degree fittings to ensure that each line is offset. While you’re doing it, you should also replace the old cutoff valve with a new ball valve (Photo 6). The diameter of the vents is determined by the amount of heat produced by the water heater. In order to achieve the ideal draft, you may need to raise or reduce the ventilation size. CAUTION: If you’re not sure whether or not your chimney has a liner, consult with a plumbing inspector. Make gas connections using solid steel pipe (Photo 8) or soft copper tubing with flare fittings (Fig. A). Both are more dependable and less expensive than flexible stainless steel connections, which are not usually allowed in some applications. For the same reasons, rigid copper water supply lines should be used rather than flexible copper water supply lines
  • If your water heater replacement is located in a location where leaking might cause damage to the floor or other elements of the home, lay a pan of an appropriate size beneath it (metal for gas water heaters). a drain tube that connects to a home drain or another suitable site must be installed in the pan (outdoors where permitted). If a leak might cause damage to the flooring, the discharge tube for the temperature and pressure relief valves must also connect to a drain. If routing is a problem, consult with your local plumbing inspector about possible solutions. Special straps should be used to secure your water heater to the wall if you reside in an earthquake-prone location (Fig. A
  • Available at plumbing stores and home centers). If they are necessary, your plumbing inspector will inform you of this. Ensure that the new water temperature setting does not exceed 120 degrees Fahrenheit to avoid scorching
See also:  How To Clean Keurig Water Filter?

Additional Information

Water Heater Maintenance: How to Make Your Hot Water Heater Last Longer Lifespan How to Repair a Leaking Water Heater Water Heater Installation Instructions on how to replace the TPR valve on a water heater Solar Water Heater Made at Home How to Repair or Replace Water Heater Dip Tubes That Are Defective How to Flush a Water Heater (with Pictures) The Process of Purchasing a New Water Heater 7 Myths About Tankless Water Heaters That You Should Never Believe The Advantages and Disadvantages of Tankless Water Heaters

How to Install or Replace a Gas Water Heater

Overview of the Process of Installing a Water Heater

  • Step 1: Measure and prepare the available area. Water should not be turned on in Step 2. Step 3:Drain tank
  • Disconnect the gas and water lines in the fourth step. Removing the overflow pipe and the pressure release valve is the fifth step. Step 6: Vacuum the floor
  • Step 7: Attach the flue hat. Step 8: Solder the gas line together. Step 9: Turn on the pilot light.

There are few things that are more frustrating than a broken water heater. When there is no hot water, there are no clean dishes or clothing to wash, and you have to take chilly showers. You should consider replacing your water heater if you’re having troubles with your current unit. DIYing the replacement of your air conditioner might save you money. This Might Also Be of Interest to You: What is the approximate cost of repairing or replacing your water heater? When shopping for a new water heater, it is important to understand that water heater installation is not a task for inexperienced individuals.

Furthermore, if you make a mistake throughout the procedure, you might do harm to your home.

Knowing how to connect the water and gas lines to the new heater, as well as how to start the pilot light, will be necessary.

Can I Install a Gas Water Heater Myself?

You can easily do a gas water heater installation on your own if you’re confident in your abilities; but, if money is your major concern, it may actually be more cost-effective to hire a professional to assist you. The Consumer Reports website states that 90 percent of water heater replacements are necessary because the previous water heater has failed. If you don’t know how to install a gas water heater, you don’t want to have to figure it out when water is gushing all over the place. It might also be dangerous to do it on your own if you have no prior expertise or knowledge of the subject.

A gas leak is not a DIY job you should take on unless you are prepared to take a significant risk to your house and the environment.

What Kind of Water Heater Do I Own?

To properly install a new water heater, you must first remove the old one that is currently installed. In order to remove a gas water heater, you will have to put up more work than if you are using an electric water heater. Electric water heaters are distinguishable from their gas counterparts by the fact that they are powered by a cord and are not linked to a gas line.

Because each water heater is slightly different, it’s a good idea to make a note of the make and model of your water heater as well. Make sure you have your copy of the handbook handy so you can follow the directions on how to securely switch off and flush out the system.

Choosing the Right Water Heater

Pick whether you want to fuel your water heater with natural gas or electricity, and then decide whether you want a tank-style water heater or a tankless water heater. The choice between gas and electric will be the more significant one since it will have the most influence on your monthly energy bill and maintenance expenditures.

Electric Water Heaters

Electric water heaters are the most straightforward to set up. In addition, they are less expensive to acquire. However, there are certain disadvantages to using them. Here are some pros and downsides to take into consideration:

  • Electric water heaters require less maintenance than gas water heaters since they are not linked to a natural gas line. As a result, there is no danger of gas leaks, which can result in explosions or carbon monoxide poisoning. When it comes to the water heater itself, you will save money. Power, on the other hand, is more expensive than natural gas, therefore you will see an increase in your electricity costs as a result of this saving. If you lose power, you will be without hot water for a period of time since the water heater requires electricity to work. Compared to its gas-powered equivalents, electric water heaters heat water at a slower rate. Electric water heaters with high efficiency are not available on the market.

Gas Water Heaters

Installing a gas water heater will necessitate the use of more advanced skills and will take longer than installing an electric water heater. If you’re thinking about installing a gas water heating system, there are some advantages and disadvantages to consider. These include:

  • Natural gas is significantly less expensive than electricity. In order to save money on your utilities, this is the best option for you
  • Units fuelled by natural gas heat water fast. When compared to an electric water heater, a tankless gas water heater is far more effective and efficient. If your electricity goes out, your water heater will continue to run normally without interruption. During storms or other power outages, this may be quite beneficial. Gas water heaters are more expensive to install than electric water heaters. However, because they are less expensive to operate, the money you save on your power bill will more than equal the original cost over time.

In addition, there are safety risks associated with having a gas system. A gas leak may necessitate the hiring of a professional to solve the issue swiftly, and you may be exposed to carbon monoxide and combustible gas as a result of the leak. It is possible to alleviate some of the safety issues associated with using a gas water heating system by installing carbon monoxide detectors in your house. The installation, inspection, and maintenance of your equipment should be handled by a qualified specialist.

Check your connections on a regular basis so that you are aware of when you need to make repairs.

The fact is that they are more cost-effective in the long term.

Tankless Water Heaters Vs. Storage Water Heaters

The decision on whether or not to go with a tankless unit is dependent on the amount of demand you intend to place on the unit as well as the environment in which you reside. Water heaters with no tanks take up a fraction of the area required by tanks with tanks, but they are unable to store any hot water. However, after the water is heated, they can produce around four gallons of hot water every minute, which is a significant increase over the previous model. Despite the fact that this may appear to be a lot, it may not be enough if you’re also running the shower, dishwasher, and washing machine at the same time.

  1. Another disadvantage of living in a colder region is that cold water takes longer to heat, so if you’re starting with water that comes in from chilly pipes, it will increase the amount of time it takes to warm the water.
  2. Tank systems are significantly more common, and the majority of homes are already equipped to accommodate them.
  3. An unvented tanked system works by continuously heating the water in your storage tank, allowing you to have hot water on demand anytime you turn on the water faucet.
  4. The majority of individuals choose for a tank with a size between 40 and 55 gallons.

Because the water in the tank is always hot, you waste a significant amount of energy heating water that may or may not be utilized, making these systems less environmentally friendly than other options. Additional Related Articles:

  • What is the best way to drain a water heater? Is it a tankless job? Determine whether or not a tankless water heater is appropriate for your home. What is the procedure for turning on my water heater? Don’t Forget to Flush Your Toilet! The following is a 6-Step Guide for Flushing Your Gas or Electric Water Heater: Instructions on how to relight the pilot light on your water heater

How Do I Install a Gas Water Heater?

When dealing with gas lines, the most important thing to remember is that safety comes first. Make certain that your gas and water are totally turned off while you are working in order to avoid mishaps and serious injury. Before using the new system, check to see whether there are any leaks. If you are not familiar with all of the safety standards for installing a water heater, we do not advocate attempting to do it yourself. An installation guide for the most popular form of water heater, a gas unit with a storage tank, is provided in this step-by-step instruction.

Step 1: Measure and Prepare the Space

The most effective method for accomplishing this is to measure the unit you presently own and then purchase a new water heater that matches those measurements. Make certain that the new water heater complies with any applicable local laws or ordinances so that you don’t install it only to discover that you have to remove it because it doesn’t meet the requirements.

Step 2: Cut Off the Water Supply

Close the water main shutoff valve, which will shut off the water supply to your whole home. In addition, turn the water control valve on the unit itself to the off position. Then, turn on all of your faucets around your house to drain as much hot water as you possibly can from your system. Keep the faucets open while the old unit is being removed.

Step 3: Drain the Tank

Drain the tank by attaching a hose to the drain valve and turning it on. You can direct the water to a location outside your house, or you can dump it into buckets or a drain in your home that feeds to the sewage treatment plant. Even though this procedure may take a few minutes or longer, it’s critical to ensure that the tank is completely empty before proceeding.

Step 4: Disconnect the Gas and the Water

A tubing cutter will be required for this stage, if the lines have been soldered together before. Because your water should already be turned off, begin by turning off the gas to the water heater. If you don’t notice any shutdown valves near the heater, you’ll have to turn off the main water supply to the house instead. Sanding the pipe before you detach it could make it easier when you need to solder the new pipe. Remove the gas pipes, but leave the tank tee and sediment trap in their original locations for safety reasons.

Step 5: Remove the Overflow Pipe and Pressure Release Valve

These will be connected to your newly purchased unit as well. It will be necessary to disconnect your old water heater from the gas exhaust, but you will be able to keep the vent hood in place. Because it will be so hefty, removing your water heater may prove to be a difficult task. Make certain that you understand how and where to dispose of it before moving anything else around. More information on how to dispose of old water heaters may be obtained by contacting your local trash management organization.

Step 6: Clean the Floor

All of them will be linked to your new unit. Your old water heater must be disconnected from the gas exhaust, but the vent hood should remain in place. Because it will be so hefty, removing your water heater may prove to be a difficult task.

Before you relocate anything, you should make certain that you understand how and where to discard it. For additional information on how to dispose of old water heaters, contact your local trash management organization.

Step 7: Hook Up the Flue Hat

Install the heat trap fittings and water line connections in the reverse sequence of the removal: first connect the flue hat to the gas exhaust vent, then connect the heat trap fittings and water line connections. In the event that you do not properly install them, your water flow will be disrupted, and hot water will not be delivered to your plumbing system. Make sure you’re feeding the lines in the correct direction by following the directions on the lines.

Step 8: Solder the Gas Line

Install the heat trap fittings and water line connections in the reverse sequence of the removal: first, connect the flue hat to the gas exhaust vent, then connect the heat trap fittings to the water line. In the event that you do not properly install them, your water flow will be disrupted and hot water will not be delivered to your plumbing system. Make sure to follow the directions on the lines to ensure that you’re feeding them in the proper manner.

Step 9: Light the Pilot Light

Finally, re-ignite the pilot light and re-connect the water supply. Make careful to turn off any faucets that were left open prior to this procedure.

Is It Difficult to Replace a Gas Water Heater?

Installing a gas water heater is not normally a do-it-yourself project for most homes; you cannot learn how to install a gas water heater in a day or two. If you are not adequately equipped and have no prior plumbing knowledge, doing this procedure can be highly risky. There are a plethora of possibilities for things to go wrong. In addition, you must ensure that your system complies with all applicable building requirements in your area. We recommend that you use a professional plumber for installation since a plumber will be able to install your unit quickly, will frequently be able to dispose of the old unit, and will be familiar with the standards and regulations that control what sort of system you are permitted to install.

How Long Does It Take to Install a Gas Water Heater?

A competent plumber can generally perform the installation in less than two hours with the proper tools. Given the weight of a tank-style water heater, a plumber may enlist the assistance of a coworker in order to complete the removal successfully. It’s possible that you won’t be able to move the unit on your own. If you have no prior expertise, the procedure might take several hours — or possibly all day — since you will need to spend a significant amount of time making sure you understand where everything is supposed to go.

Gas Water Heater Installation: A Step-by-Step DIY Guide

Gas water heater installation may appear to be a job best left to the professionals, but it is not quite as complex as you may assume. Certainly, hiring a professional to complete the work for you is the most convenient option to complete the task at hand. Installing your gas water heater, on the other hand, is a great do-it-yourself project if you want to save a little money while also gaining a sense of accomplishment. In most cases, it’s advisable to go with the same fuel type (gas or electric) when purchasing a new water heater unless there’s a compelling reason to do otherwise.

They can provide you with information about the local plumbing codes as well as whether or not you will require a municipal permit.

If you hire a professional, you won’t have to worry about this since they will remove your old water heater from your property for you. It is not difficult, however, to replace a gas water heater if you like DIY projects and would want to save money in the process.

Preparing to Install a Gas Water Heater

The chances are considerable that your water heater has reached the end of its useful life and will need to be replaced if it is more than 10 years old. Prior to purchasing a new water heater, however, it is worthwhile to attempt to resolve the issue first using the methods described above. If your water heater is leaking, it is possible that the problem can be resolved. However, if the cause of the leak is from the tank itself, you will need to replace the unit.

Tools and Supplies Needed

  • Examine the label on the back of your old water heater. It should include information on the annual energy consumption as well as the tank capacity. Having both of these details handy while searching for a new water heater is a great idea. Before removing your old water heater, we recommend that you examine your water heater vent system to ensure that it is in excellent operating order and that it is functioning correctly. Remove your old heater by disconnecting it and draining it, then removing it with a hand truck. If there is an excessive quantity of sediment buildup in your water heater tank, the drain valve may get clogged. This article will guide you through the process of draining the tank. Take caution when handling the vent pipe. In good condition, you may use it with your new water heater to save money on your energy bills. This is also possible if the Temperature/Pressure Discharge Pipe is in good condition
  • However, this is not always the case. If your water heater was plumbed with copper pipes, you may need to use a tubing cutter to cut the copper pipes in order to repair them. Keep as much pipe as possible intact if this is the case.
See also:  How Do You Dispose Of A Water Heater?

Find Local Plumbing Professionals

How to Install a Gas Water Heater

Follow these step-by-step instructions to learn how to install a gas water heater, and then watch the video to learn more.

Install Earthquake Straps

The first step is to use a tape measure to determine the placement of the two earthquake straps.

  • In the case of an earthquake, these seismic straps will aid to support the tank against the wall, so preventing it from tumbling over. Measure the water heater from the ground up and mark the wall with the relevant measurements: The top earthquake strap should be a few inches below the T P Valve. The lower strap should be positioned a few inches above the gas regulator, and vice versa.

By measuring from the ground up and noting the height with a pencil, you can determine where the picture should be hung on the wall. The seismic strap bracket should be mounted to the wall. Make certain that the screw “catches” a stud. When not in use, the seismic strap should be placed next to the tank. In order to properly tighten the screws, it may be required to “swing” the bracket 180 degrees. Install the new water heater in its proper location. Placing the water heater in a drain pan and connecting the existing piping to the inlet and outlet connections of the water heater are the next steps.

It is not necessary to secure the water heater with earthquake straps.

Connect the Water Supply

By measuring from the ground up and noting the height with a pencil, you can determine where the picture should be placed on the wall. Attach the seismic strap bracket to the wall using the screws that came with your bracket. Double-check to see that the screw ” grabs ” the stud. The earthquake strap should be placed close to the tank for further stability during an earthquake. In order to properly tighten the screws, you may need to “swing” the bracket 180 degrees. Install the new water heater in its designated location.

To allow for future maintenance, make sure there is enough space between the wall and the water heater.

CALL NOW!

Measure from the ground up and mark the height of the object on the wall to determine its correct location. Attach the seismic strap bracket to the wall using screws. Make certain that the screw ” catches ” a stud. When not in use, the seismic strap should be stored adjacent to the tank. In order to fully tighten the screws, “swing” the bracket 180 degrees if necessary. Place the new water heater in its proper location.

Place the water heater in a drain pan and connect the existing piping to the inlet and outlet connections on the water heater. Make sure there is enough space between the wall and the ater heater to allow for future servicing. Make no attempt to secure the water heater with the earthquake straps.

Install the Vent Hood

Determine the right placement on the wall by measuring from the ground up and noting the height with a pencil. Install the seismic strap bracket on the wall. Check to see that the screw ” catches ” a stud. The earthquake strap should be placed adjacent to the tank. If required, “swing” the bracket 180 degrees before fully tightening the screws. Install the new water heater in its designated location. Place the water heater in a drain pan and connect the existing piping to the water heater’s inlet and outlet connectors.

Do not secure the water heater to the seismic straps.

Install the Vent Piping

4. If your vent pipe is not damaged, you should be able to reuse it with your new water heater. Consult your water heater’s owner’s handbook to determine the proper vent pipe diameter. If the suggested vent pipe diameter is greater than the diameter of the vent hood, a reducer should not be utilized. In order to begin assembling the adjustable vent pipe, insert one end into the water heater vent hood and join the remaining pipe components. Check the manufacturer’s instructions for your water heater to ensure that the diameter is proper.

This will allow the vent pipe to be aligned as closely as possible to a straight line.

To attach the vent parts to the water heater vent hood and to the other vent sections, use self-tapping sheet metal screws to fasten them together.

Check your local code for requirements.

Install the Gas Connection

Step 5Confirm sure the gas supply is turned off by turning it on and off again. Cleaning the pipe fitting on the supply pipe with a wire brush is then necessary. By opening and shutting the valve, you may flush the line. Remove the sticker from the water heater’s gas control valve and replace it with a plug. This is the location where the gas line will be connected. Remove the gas nipple from the flexible gas line by unscrewing it. Many places, particularly earthquake-prone ones, necessitate the installation of flexible gas lines.

  1. Find a Local Plumber Today is the day to fix your plumbing emergency!
  2. It is not necessary to cover the first few threads with pipe joint compound, as seen in the video.
  3. To tighten the gas nipple, insert it into the gas control valve and tighten it with a wrench.
  4. When tightening, however, take care not to harm the gas control valve in the process.
  5. One wrench on the nipple, and the other holding the gas control valve.
  6. Make sure not to kink the line in any way.
  7. Tighten the connections by hand first, and then with a wrench to make them even tighter yet.
  8. Find Local Plumbing Professionals Open the water inflow valve and begin filling the tank with water as quickly as possible.
  9. While the tank is full, check for leaks at the hot and cold flexible water lines’ ends on both the hot and cold flexible water lines.

Allow the water to run for a few minutes before turning it off. This will get rid of all of the air that is currently in the tank. As long as the tank is not completely filled and all of the air has been drained out of the tank and lines, the water will splutter.

Connect the Earthquake Straps

Seventh step: Wrap a pair of earthquake straps around the water heater and attach them together. Avoid pulling the straps too tightly; they should be snug but not too so. Then, using clips, secure the extra strap in place. Find Local Plumbing Professionals

Connect the T P Drain Pipe

Step 8If the T P drain pipe from your previous water heater is in good condition, you may be able to reuse it. However, it is possible that you will need to construct a new T P drain pipe. To do this, use a tube cutter to measure and cut a copper pipe. Put a bucket underneath the T P drainage pipe if you do not have a floor drain installed. The end of the drain pipe should not be more than 6 inches above the ground or the bucket it is connected to. Turn on the gas supply valve. To ignite the pilot, go to the owner’s handbook for your water heater.

  1. Place the lower dial on the gas regulator to ” Pilot Lighting ” and then turn the control knob on the gas regulator to ” PILOT ” mode to complete the process.
  2. Once you have waited a few seconds, click the ignitor button while simultaneously pressing the control knob to start the engine.
  3. Another type of sight glass will allow you to visually inspect whether or not the flame has caught.
  4. If the flames were to ignite:
  • Press the control knob for 45 to 60 seconds in a continuous motion. After releasing control knob, double-check to see if the pilot is still glowing. To switch on the pilot if it is still lighted, move the control knob to the ON position.

Lower the dial to the temperature you choose for your drinking water. As a starting point, make use of the manufacturer recommended configuration. The ideal temperature setting is 120 degrees.

Test Gas Lines for Leaks

Step 10: Check for gas leaks by spraying any gas connections with a flammable liquid. Alternatively, you may make your own solution (1 part dish detergent to 2 parts water) or use Leak Detection Solution. If you see any “bubbling,” this indicates that gas is leaking. Applying a wrench to the loose connection and checking it again is recommended.

Watch the Video

After you’ve completed the installation of your gas water heater, there are a few further considerations to make. First and foremost, always check your vents to ensure that they are drawing correctly. If they are not, we urge that you seek the assistance of a specialist to fix the matter. You may learn how to do this by watching the video below.

Watch the Video

After a couple of hours, examine the T P discharge pipe for leaks or damage. The fact that the hose is pouring indicates that the pressure inside your tank is likely to be excessive. Turn off the gas supply and contact an expert as soon as possible. Keeping a carbon monixide detector close by your gas water heater is strongly recommended by us. They are affordable and will inform you if you are in a potentially hazardous position. Repair and Installation of Water Heaters at the Lowest Possible Price Now is the time to call!

How Much Does Water Heater Installation Cost?

Water heaters are one of the most often used household appliances in households all over the world, especially in developing countries. In the winter, having a running water heater is nothing short of a gift. When planning a water heater installation project, one of the factors to take into consideration is the cost of the installation. It costs $400 to $900 to install a 40-50 gallon water heater with a tank, depending on the size of the unit. The cost of installing a tankless water heater typically ranges between $1,470 and $2,500 in most cases.

When it comes to the entire cost of owning a water heater, a variety of elements must be considered, including the number of people who will be using the heater, running expenditures, and any renovation that has been done in the home.

Tank vs. Tankless Systems

Among the most often utilized domestic equipment in households all over the globe, water heaters are one of the most common. Water heaters that work properly are a godsend during the cold months. When planning a water heater installation project, one of the factors to consider is the cost of the installation. It costs $400 to $900 to install a 40-50-gallon water heater with a tank, depending on the model. For a tankless water heater, the installation cost is typically in the $1,470 to $2,500 range.

Labor

Plumbers often bill between $45 and $65 per hour. In most circumstances, a plumber can complete the installation of a water heater in a single day (6-8 hours). You should anticipate to pay anything from $270 and $520 for this service. Water heaters that are difficult to access may require an additional 2 to 3 hours of installation time.

Type of Water Heater

Natural gas water heaters, propane water heaters, electric water heaters, and solar water heater systems are some of the most common types of water heater systems available on the market. Natural gas systems are well-known for being affordable ($500-$700 per system). For a natural gas water heater replacement in Alpharetta, you should budget between $400 and $550 dollars. Installing a new natural gas water heater system can cost you between $1,500 and $2,300 on average, depending on your location.

Although the average cost of installing an electric water heater is between $350 and $450, the initial cost might reach $500 if the installation is complicated due to structural issues.

Additional Considerations

If you wish to replace an old water heater, you should budget an additional $500 to the entire cost. Purchasing new piping will be necessary if your existing water heater pipe is broken or not compatible with the new system. New piping will cost between $8 and $10 per linear foot. Check with your plumbing contractor in Alpharetta to see whether you are required to obtain permits for a new water heater installation. Fletch Barney is the final stop in your hunt for a plumbing specialist. We have earned a reputation as one of the most dependable plumbing companies in Alpharetta.

Call us at 770-333-3031 if you’d like to speak with a professional about your project.

Who Is Qualified to Perform a Gas Water Heater Installation? – Maeser Master Services

In spite of the fact that installing a new propane hot water heater may not appear to be a huge concern, it entails working with potentially dangerous systems that not every homeowner is equipped to handle without assistance.

The following information will provide you with everything you require when deciding who will perform your gas water heater installation.

The Basics: How to Install a Gas Water Heater

If all you have to do is substitute out your water heater, it may appear to be a straightforward procedure. Initially, it appears to be a straightforward process: you drain the old tank, cut off the gas and water, unplug and carry away everything associated with the old heater before installing the new heater. There aren’t many attachments to disconnect; the only ones are the gas supply and exhaust (flue), as well as the lines for cold and hot water coming into and out of the unit. However, even though it appears to be a straightforward project that doesn’t take much time to complete, home improvement websites such as Home Depot classify the complexity of gas water heater installation as “advanced.” For a good reason, this is the case.

Safety Concerns

Despite the fact that the installation appears to be straightforward, it is the fact that you will be working with gas that warrants the “advanced” classification for this operation. Working with gas has the potential to be extremely harmful for you, your family, and anybody else who may be in close proximity to your house or who may share walls with you. When you install your new water heater, you will need to switch off the gas to allow you to detach the supply line and connect it to the new hot water heater, which will take some time.

Once you’ve completed the installation of the new heater, you may turn the gas back on, but you’ll need to inspect the gas line for leaks.

The difference between an amateur and a professional installer is that the former has more experience working with gas lines and thus requires less trial and error, while the latter has the equipment to detect gas leaks with greater certainty, thereby making you and your family safer.

Plumbing Expertise

Despite the fact that the plumbing necessary for gas water heater installation does not pose the same risks as working with gas lines, it is nevertheless recommended that the individual performing the work has some prior plumbing expertise. Additionally, depending on the age of the existing heater and how it was placed, as well as whether or not the replacement is an improvement, it may be necessary to repair the piping as well.

Updates and Upgrades

If your system has to be upgraded to meet contemporary requirements, or if you’re thinking about upgrading to a more advanced hot water system, such as a tankless gas water heater, you’re looking at a considerably more involved project than just replacing out one water heater for another. If you’re replacing a standard storage water heater with a tankless system, you’ll need to retrofit the tankless system with new gas lines, new water lines, and a new ventilation system, which will make the conversion considerably more difficult for the ordinary do-it-yourselfer.

Professional Gas Water Heater Installation

To ensure your safety when replacing your water heater, you should consider hiring a professional to complete the job for you. As well as keeping you and your family safe by avoiding rookie mistakes, it also means getting the job done swiftly and effectively so that you can go back to your usual routine promptly. Additionally, you may consult with a qualified specialist about your upgrade choices, which can assist you in determining whether a more powerful hot water system is appropriate for your family.

Make a call to Maeser now for additional information on gas water heater installation or to make an appointment with one of our knowledgeable specialists.

How to Replace a Water Heater

This Old Houseplumbing and heating professional Richard Trethewey demonstrates how to replace a water heater in this instructional video.

Steps for replacing a water heater

  1. Shut off the cold-water supply line that leads to the water heater. Immediately turn off the gas feed to the heater. Using a yard hose, drain the water from the heater
  2. And To disconnect the cold- and hot-water pipes that are attached to the heater, use a tubing cutter. Remove the union that links the gas line to the heater and set it aside. Dispose of the old water heater
  3. Install the new heater on top of the blocks. Connect the exhaust flue to the top of the heater. Solder a new copper pipe to link the heater to the cold- and hot-water supply pipes. Reattach the gas line to the heater. Attach the vacuum valve to the top of the heater. Threads should be wrapped in Teflon tape and tightened with pliers. Fill the tank with cold water by turning on the faucet.
See also:  How To Detect A Gas Leak From Water Heater?

Are you looking for further assistance with home repairs? A house warranty may be of assistance. The This Old House Reviews team has put up some in-depth guidelines that you can read here:

  • Home warranty companies that are the best
  • Reviews of American Home Shield, AFC Home Club, Select Home Warranty, and Choice Home Warranty are all available.

Tools

Despite the fact that it’s a tankless job, someone has to do it. Leaving aside the dad jokes, installing a tankless water heater is a serious undertaking that should be approached with caution. Our goal is to make this process as simple and pleasant as possible, so we’ve included step-by-step instructions for both gas and electric units below. Take note that replacing a tankless water heater is a time-consuming process requiring advanced technical knowledge. So, if you aren’t confident in your plumbing and electrical abilities, it is preferable to engage a licensed professional – in certain areas, this is a legal requirement.

How to Install a Gas Tankless Water Heater

Installation and replacement of tankless water heaters may be quite expensive, as we realize. Installing your own unit is doable, but we recommend that you proceed with caution. This should only be attempted if you have extensive experience working with gas lines, water lines, and electrical systems. Installing your tankless water heater incorrectly might result in significant harm to your home. Unsafe gas line installation may cause explosions, while faulty gas venting can result in deadly carbon dioxide leaking into your house.

If you are considering a do-it-yourself installation, it is critical that you understand the terms of your insurance policy.

You can install your unit yourself if you are confident in your abilities and have double-checked with your insurance company.

Step 1

Installation and replacement of tankless water heaters may be quite expensive, as we are well aware of this. Installing your own unit is conceivable, but we must issue a word of warning to potential customers. If you are not comfortable with working with gas lines, water lines, or electrical systems, you should not attempt this project. The incorrect installation of a tankless water heater might result in extensive damage to your property. Unsafe gas line installation may cause explosions, while faulty gas venting can result in deadly carbon dioxide leaking into your home.

You should be aware of the specifics of your insurance policy if you want to do a DIY installation.

You can install your unit if you are confident in your skills and have double-checked with your insurance company. The procedures listed below will guide you through the process.

Step 2

Make certain that you obtain all necessary state or local permissions before installing or upgrading a water heater.

Step 3

For water pressure more than 80 psi, you’ll need to install a pressure-reducing valve upstream of the new water heater before it will work properly. When establishing the cold and hot water connections (as described in the section below under “Establish the cold and hot water connections”), you should consider whether or not you need to install one.

Step 4

  • Make sure you check your local construction codes to see where you may put your water heater in your home. These tankless gas systems must be vented directly to the outdoors, rather than through a chimney, in order to function properly. Consequently, it is vital to identify a position where the unit may readily vent outdoors while also complying with local code requirements for vent placement. Carefully review the manufacturer’s installation instructions to ensure that you have adequate clearance around the device
  • Stay away from locations where:
  • Temperatures below freezing might have an impact on the unit. Any form of liquid might be sprayed on the device on a regular basis. There is a significant amount of humidity and wetness

Step 5

It is possible that the unit will be damaged by freezing temperatures: Regular splashes of any form of liquid might damage the device. Humidity and moisture levels are quite high.

Step 6

  • Tankless gas water heaters consume more gas than traditional tank-style water heaters. Determine whether or not your present gas line will be sufficient initially
  • If not, upgrade it. A professional contractor will be required to install a newer, larger gas pipe if your present gas line is unable to keep up with the demand.

Step 7

  • If there isn’t a shut-off valve before the heater, cut off the main water supply
  • Otherwise, turn off the heater. Remove the heater from service by closing all power and gas supply valves to it. Drain the contents of the unit.
  • When dealing with hot water, utilize a hose that is designed to tolerate high temperatures. To relieve pressure in the system, open a hot water faucet for a few minutes. Allow it to completely drain

Removing the water heater from the gas and water supply pipes is necessary. Make sure to properly dispose of your old water heater.

  • For information on how to properly dispose of it, contact your local recycling and/or sanitation agencies.

Step 8

  • Ensure that the device is properly supported by constructing a mounting box that is approximately four inches away from the wall. The foundation wall should be properly secured with appropriate anchors. Follow the manufacturer’s instructions for mounting the device to the box firmly.

Step 9

  • Hiring a professional contractor should be your first choice unless you have extensive knowledge with gas line installations. Utilize a threaded black iron pipe to connect the existing tee to the unit position if your present gas line is the suitable size and you can connect it without breaking the existing connection. Remember to switch off the main gas line before removing the down pipe from the previous unit if you’re replacing it. After ensuring that the gas line is routed to the right location, you should install a tee, a sediment trap, and a gas shut-off valve. The shutdown valve and sediment trap should be connected to the heater in accordance with the manufacturer’s instructions. Install a new gas supply line from the tee to a location where it can be conveniently connected to the gas line of the new unit. You may utilize a black pipe or a flexible gas supply line to accomplish this task. Assemble the connections in the direction of the heater, starting with the tee, using two wrenches. Whenever possible, use thread sealant developed for gas lines when connecting gas pipe assemblies. After you have completed all of the gas line connections, you should test the line. Before turning on the gas, check the pressure with a pressure gauge.

Step 10

  • Connecting the water heater valves to the water supply line should be done according to the manufacturer’s instructions.
  • Connecting new hot and cold water lines to existing water lines should be done with copper pipe. Continue to connect the wires to the new unit. It is possible that copper pipe will need to be cut and soldered to the unit.

Depending on whether your water system includes an anti-siphon valve or a check valve on the supply line, you may require an expansion tank close to the cold intake. More information may be found in your vehicle’s owner’s handbook. Bell hangers should be used to secure the pipe to the wall. Place the pressure relief valve in its proper location. Installing a purge valve and a pressure relief valve should be done according to the manufacturer’s instructions.

Step 11

  • Make sure there are no leaks by turning on the water supply. To check for leaks, turn on the gas and wait a few minutes. It is possible that you will need to bleed the line. Afterwards, switch off the gas supply until the installation is complete.

Step 12

  • When it comes to correctly venting the device, follow the manufacturer’s recommendations as a reference. There’s a considerable probability that you’ll be able to vent your water heater straight through the rim joists in your home. Only utilize pipes that have been specifically designed for this sort of venting. In some cases, depending on the manufacturer, you may require a vent kit. Make sure that the vent shaft of the new unit is sealed with a heat-resistant silicone sealant. Afterwards, attach a connection to it and secure it with an appropriate hose clamp
  • Place a length of stainless steel vent pipe on top of the structure. Put on a retaining ring to keep it in place. Folding over the tabs can help to keep it secure. Slip an elbow inside a pocket. Make sure that the aperture faces the direction in which the unit will vent to the outside
  • Select a spot on the joist or wall that will serve as the center of the vent hole for the purpose of venting outdoors. Drill a hole from the inside of the building at the location you’ve picked. Make a circle on the outer wall with a vent thimble and tape it in place. A spade bit should be used to bore a 1-inch hole at the center of the circular. Remove siding and shingles from around the vent hole in order to allow the flange thimble to be flat against the outside wall
  • Caulk around the edge of the flange with silicone caulk to seal the edge of the flange to the outside wall. Then, place the flange into the vent hole that has been created. Use screws to securely fasten it to the outer wall and silicone to seal the screws in place. Installing the internal flange should be done from the inside. A portion of vent pipe should be routed through the flange aperture. Tabs should be used to secure each part. Attach a short portion of vent pipe to the outside of the house and then connect the vent hood
  • Put the shingles and siding back on the house that you removed previously.

Step 13

  • To remove air from the water pipes and heater, turn on the faucet to its full “hot” setting. Close the water supply valve

Step 14

Connect the water heater to the wall outlet. That is all there is to it.

Step 15

The hot water line that originates from the water heater should be insulated.

Step 16

The gas should be turned on when the installation is complete. Your water heater should be up and running at this point!

How to Install an Electric Tankless Water Heater

Installation and replacement of tankless water heaters may be quite expensive, as we realize. Installing your own unit is doable, but we recommend that you proceed with caution. This should only be attempted if you have extensive experience working with water lines and electrical systems. Installing your tankless water heater incorrectly might result in significant harm to your home. If you are considering a do-it-yourself installation, it is critical that you understand the terms of your insurance policy.

You can install your unit yourself if you are confident in your abilities and have double-checked with your insurance company.

Step 1

Depending on the manufacturer, if their systems are not installed by certified professionals, the warranty may be voided.

Step 2

Confirm that your electrical service panel has the capacity to manage the energy demands of an electric tankless water heater before installing one. It’s possible that you’ll need to upgrade your panel or install a whole new one. It is possible to uncover useful information by inspecting your electrical breaker box or the label on the electrical panel in your home.

You might also consult with an electrician. The majority of suitable water heaters require a minimum of four 40AMP breakers to deliver hot water for a two and a half bath house.

Step 3

Examine your electrical service panel to see if it is capable of handling the increased energy demands of an electric tankless water heater. Your panel may require an upgrade or you may need to install a whole new one. You can look at the electrical breaker box or the label on your electrical panel to locate pertinent information. Alternatively, an electrician might be contacted for assistance. The majority of suitable water heaters require a minimum of four 40AMP breakers to deliver hot water for a two and a half bath residence.

Step 4

Make certain that you obtain all necessary state or local permissions before installing or upgrading a water heater.

Step 5

  • In order to heat water for the entire house, it is best to locate the unit closest to the area in which the majority of the hot water is consumed. If you’re installing a point-of-use system, try to locate them as near to the points of use as feasible. Always keep in mind that most electric tankless water heaters must be mounted vertically, with the water and electrical supply connections on the bottom of the unit. Follow the manufacturer’s recommendations for leaving a particular amount of clearance for service
  • In general, you want to stay away from locations where:
  • Temperatures below freezing might have an impact on the unit. Any form of liquid might be sprayed on the device on a regular basis. There is a significant amount of humidity and wetness

Step 6

Disconnect any circuit breakers that are connected to the new device. This is critically crucial!

Step 7

Shut off all circuit breakers that are associated with the new device and reconnect them. Obviously, this is quite significant!

Step 8

  • If there isn’t a shut-off valve before the heater, cut off the main water supply
  • Otherwise, turn off the heater. Remove the heater from service by closing all power and gas supply valves to it. Drain the contents of the unit.
  • When dealing with hot water, utilize a hose that is designed to tolerate high temperatures. To relieve pressure in the system, open a hot water faucet for a few minutes. Allow it to completely drain

Removing the water heater from the gas and water supply pipes is necessary. Make sure to properly dispose of your old water heater.

  • For information on how to properly dispose of it, contact your local recycling and/or sanitation agencies.

Step 9

  • Remove any screws that are holding the front cover of the new device in place
  • And Please keep in mind that you may need to remove at least one plug before you can set it aside.

Step 10

A set of adequate anchors and screws should be included in the box.

Step 11

  • Connections for the cold and hot water should be made. Colds are typically seen on the right side of the body.
  • The quickest and most straightforward method is to use stainless steel flex pipe with Teflon tape. You can also utilize copper tubing that has been rated for use in high-temperature environments. If you have to cut into a pipe, make sure the edges are clean. Before connecting the pipes to the water heater, flush them with water once they have been soldered. Also keep in mind that too much heat might cause harm to the water heater. If you want to do maintenance on your heater, it’s a good idea to install a shut-off valve before and after it. This will allow you to stop off the water supply to the unit without shutting off the water supply to the rest of your home
  • If you need to install a pressure reduction valve, you should do it immediately on the cold water side of the plumbing system. The installation of a temperature and pressure relief valve is unlikely to be necessary (T P). However, you should double-check your local and state installation rules to see whether or not you require a permit.

Step 12

  • By opening various hot water outlets, you may remove any trapped air from the device and the pipes. While you’re waiting, you should inspect each and every connection for leaks.

Step 13

This step must not be skipped!

Step 14

  • Heater on one side, and electrical panel on the other, is the recommended arrangement
  • Comply with the manufacturer’s wiring diagram and their instructions for selecting the appropriate wire, circuit breaker number, and circuit breaker size
  • And After cutting and stripping each wire set to the proper length, push the wires through the bottom holes in the new water heater’s housing. Then, fasten the wires to the appropriate slots on the terminal block using wire nuts.
  • For the most appropriate torque, see the product handbook. It is important to remember that a ground conductor must be connected to the circuit breaker panel and the grounding busbar of the unit for each circuit.

If you want to know what torque is best, see the product handbook. Take note that a ground conductor must be connected between the circuit breaker panel and the grounding busbar of the unit for each circuit.

Step 15

Make use of the screws that you already removed.

Step 16

The device should be turned on at this point. Select your chosen unit settings from the drop-down menu.

Step 17

Start by turning on the hot side of a faucet in your home. After the water temperature has steadied, take another reading. The temperature may be adjusted on the device itself if you desire to do so.

Learn More About Tankless Water Heaters

Right now, our plumbing professionals are here to take care of your repair needs. They’ll assess your situation, propose a solution at a reasonable fee up front, and then get to work!

Upfront Pricing

There are no hidden fees.

Quality Work

Guaranteed 100 percent customer satisfaction

24/7 Service

NightsWeekends

Leave a Reply

Your email address will not be published.