How Do You Relight A Hot Water Heater?

Steps on How To Light A Hot Water Heater

Extinguishing the pilot light flame on your gas water heater is a stressful and irritating experience.Whenever the pilot light on your water heater fails to stay lit, you will be left with no hot water at your disposal, making even the most basic chores, such as bathing, difficult.Many folks are left perplexed as to how to fire a hot water heater as a result of this.There are a variety of reasons why a pilot light may go out in addition to equipment failure, such as rapid changes in gas pressure.

The good news is that you can relight the pilot light on your heater by yourself.In this post, we’ll look at the reasons why your pilot light is turning off and how to solve the problem.

What Is a Pilot Light?

Your water heater’s pilot light is the beating heart of the appliance.Gas-powered appliances such as your water heater, furnace, and gas fireplace produce a small flame.After turning on your appliance, gases are discharged into the primary burner, where the pilot light ignites them, allowing the appliance to start on and create heat.There would be no heat or warm water if this light were not present.

Why Does Your Water Heater Light Keep Going Out?

It is possible that the pilot light is not working for a variety of reasons. Examine the following five reasons why the pilot light continues to flicker on and off:

Insufficiency of Combustible Gases

A lack of combustible air may cause the pilot light on your gas water heater to go out, and the water heater will not heat. So, what is the best way to increase the amount of flammable air available? Making sure the water heater is not surrounded by lint, debris, or grime is the most straightforward method.

Issues with Flex Tubes

This is a lengthy tube that links the gas regulator to the burner, which is where the thermocouple and pilot light, among other components, are situated, as well as other components. A flex tube that has been fractured or obstructed can prevent gas from reaching the burner.

Bad Thermocouple

If your pilot light is turned on, your thermocouple will detect it. It is necessary to set the thermocouple’s tip on the pilot flame in order to create electricity, which will keep the gas valve open. If the thermocouple senses that the pilot light on your water heater has gone out, it will cut off the gas supply to the heater.

Main Control Valve Issues

If there is a problem with the control valve, the pilot light will not stay lit. As a result of the rarity of this situation, you must rule out all other possibilities before deciding that the fault is with the primary control.

Flaws in Electrical System

Internal wiring problems are the most common cause of electrical system problems. Shorting circuits and blowing fuses are two of the most prevalent difficulties associated with electric water heaters, and an improperly wired electric water heater is particularly susceptible to these problems.

How to Light a Hot Water Heater

The presence of a pilot light can cause cold water to flow from your hot water valves if your pilot light is out. To relight the pilot light on your hot water heater, simply follow these six easy steps:

Step 1: Determine Whether You Have a Manual or Automatic Hot Water Heater

You must be aware of the type of water heater that you are employing. To establish the brand of your hot water heater, look at the silver box that protrudes from the side of the unit. It is possible that detailed instruction manuals for your individual model are available, and they can aid you with re-igniting the pilot light on your water heater.

Step 2: Turn the Gas Off

The following step is to depress the gas pedal. You’ll find the gas regulator valve on the gas line near the base of the hot water heater, which you may turn on or off. Allow at least five to six minutes for any leftover gas to dissipate after you have turned the valve to the ″off.″

Step 3: Find the Pilot Light

Make certain that the pilot light is turned on. The use of a flashlight will almost certainly be required for this procedure. It is possible to locate the pilot light under the water tank. Keep in mind that you’ll have to unscrew the access panel in order to get to it. A flame will appear at the end of this pipe if the pilot light is turned on. Otherwise, it’s game over.

Step 4: Push Down the Gas Valve and Set It to the “Pilot” Setting

Following your confirmation that there are no gas leaks in the water heater unit, you can turn on the hot water heater light again.In the ″pilot″ mode, tap and hold the reset valve for a few seconds.A red button with the word ″pilot″ will most likely be found on your heater if it has a different button.On your unit, you should also check for instructions that will guide you through the process of locating the valves and buttons that are required to relight your hot water heater light.

Step 5: Light the Pilot Burner

The water heater will be equipped with a ″ignition″ button, which will be either red or black in color.If you hit this button, your pilot light will be re-ignited once again.A tiny ″click″ sound will be heard after the process is complete.If you have a manual or an older model, you may need to give the pilot light a spark in order to relight it.

The safest method for accomplishing this is to use a long lighter, such as those used to light grills.CAUTION: Do not relight the pilot light using a cigarette lighter or a match, since doing so increases the danger of burning your hand or yourself.

Step 6: Check Whether the Flame and Heater Is On

After lighting the pilot light, keep the regulator valve open for at least a few minutes to allow the thermocouple detector to rewarm and become operational.It detects when your light goes out and switches off your water heater if the temperature falls too low.When you have a minute, slowly remove the regulator valve and check to see whether the pilot light is still blazing.If this is the case, the regulator valve should be opened.

A whooshing sound will be heard, which indicates that the primary burner has been re-ignited.As a result, your pilot light should be ready to be used at this point.

Endnote

If you follow these easy procedures, you’ll be able to properly fire a hot water heater without risking injury.The pilot light is a little light that performs a key function by ensuring that you have enough warm water for cleaning and other home activities when the power goes out.Just like with any other piece of household equipment, it is important to undertake the appropriate cleaning, yearly maintenance, and exams on it in order to maintain it healthy and sturdy.If you’re still not sure what you’re doing or don’t understand how your model works, you should consult with a professional.

This might be of interest to you: The operation of a gas water heater

How to Light a Water Heater

Article to be downloaded article to be downloaded You may see cold water flowing from your hot water faucet if you reside in a home that has a natural gas water heater.This is a good indication that your pilot light has gone out.It is not necessary to hire a professional in most circumstances; you will have hot water again in a matter of hours if the pilot is re-ignited correctly.While having your water heater’s instruction manual on hand is a good idea, it is not fully required because most gas water heaters need a similar process for relighting the pilot light, as described in this article.

1 Make that the pilot light is working properly.You will most likely need to remove a tiny panel at the bottom of the tank, known as an access panel, in order to determine whether or not the pilot light is truly turned off.If you do not see a little flame flickering, this indicates that your pilot light has been turned off.Depending on your water heater model, it is conceivable that your panel is not detachable and that you must observe your pilot light via a transparent window.

In this instance, if you are unable to see a flame burning through the glass, your pilot light is not working properly.

• 2 Check to see whether there is any gas leaking. Never attempt to restart your pilot light if there is gas leaking from your water heater, as this is highly harmful to both you and your property. Instead, call 911 immediately. To check for leaks before attempting to relight the pilot, perform a basic smell test on the cylinder. Standing near to your water heater, sniff the air to see if you can notice any strange aromas. After that, get down on your knees and smell around any valves on the front and sides of the tank. Naturally, natural gas has no odor. To make it noticeable to humans, gas companies add an ingredient known as mercaptan to the mixture. The smell of leaking gas is similar to that of sulfur or rotting eggs.
• If you detect the presence of gas in either of these locations (even if it is a faint odor), do not attempt to relight the pilot. Remove yourself from the vicinity of the water heater and contact your gas provider immediately
• they will advise you on what to do next.
• Also, keep an ear out for hissing sounds near the water heater, which might indicate a gas leak.

1. Promotional material
2. 3 Instructions may be found on the inside of the door panel of your water heater. Detailed instructions for your specific water heater model may be available here, and following them may assist you in the process of relighting the pilot for your unique water heater. Advertisement

1. Step 1: Lower the temperature control setting to the lowest possible setting. This is normally placed on the front of a box that may be found on the outside of the water heater.
2. 2Find the regulator valve on the water heater. When this valve is turned off, the pilot burner beneath the hot water tank will not operate. This valve is normally found in a similar location as the temperature control, however it is most likely positioned on the top of the box.
3. 3Turn the knob to the ″Off″ position. Wait 10 minutes after turning off the knob before proceeding to ensure that any remaining gas from the tank has cleared the air before continuing. The most important thing is to be safe!
4. 4
5. Determine the type of water heater that you have installed. Gas hot water heaters are often classified into two categories: ″new″ and ″ancient.″ Traditional heaters will require you to relight the pilot light with your own flame, however newer design tanks are fitted with a pilot light igniter built into the tank. However, while the specific appearance of the buttons on modern design tanks may vary, many of them include a red igniter button that is located a few inches away from the temperature and regulator valves.

5 Gather any lighting items that may be required.You will need to obtain a long-reach ″wand″ lighter or fireplace matches to relight the pilot on an older design water heater.Avoid attempting to relight a pilot with a conventional matchstick or a small cigarette lighter since doing so will force you to place your fingers in a small, tight position too near to the open flame, putting you at risk of being burnt.

6Travel to the location of the pilot. The pilot is positioned at the end of the little silver tube that comes out of the control valve and is connected to the control valve. It’s possible that you’ll need to use a flashlight to see clearly in this location. Advertisement

1 Turn the gas valve to the ″Pilot″ position and press the button on the valve. It is necessary to do this in order to initiate the flow of gas into the tube that supplies the pilot light. Find a red control button near the gas valve on your water heater if the gas valve on your water heater does not press down properly. Keep your finger on this button.

• 2 Light the pilot burner with a match. The pilot gas valve or the red button will be held down with one hand while the other hand will be used to swiftly light the pilot. To use this button, make sure you have a new model water tank with a built-in ignition switch installed. You should be able to hear a clicking sound until the pilot burner comes on. If you have an old-fashioned heater, ignite the pilot burner with a wand lighter or match and wait a few minutes.
• Because you will be using one hand to push the valve/red button while using the other hand to ignite the pilot, you may require the assistance of another person to carry a flashlight for you if you require additional lighting. Make an effort to get assistance in advance so that you do not go halfway through a procedure only to be forced to halt because you are unable to see what you are doing

1. 1 Minute after the pilot light has been ignited, keep the gas valve or control button down by pressing it down one more time. This will heat the thermocouple, which is a sensor that turns off the gas when the pilot is not lit.
2. 4Release the valve knob/control button to complete the process. After a minute, open the valve and press the control button to check if the pilot light is still on.
3. 5Remove the access panels and replace them. When checking to see if the pilot light is still lit, replace the access panel (if you had to remove it first) to ensure that no flames escape into your home.
4. 6Restart the main burner. Turn the main gas valve back to the ″On″ position and set the temperature control to the appropriate temperature. The main burner under the tank should be turned on and the water in the tank should begin to heat. Caution: When turning the knob to ″on,″ be careful to keep your head away from the burner area.
5. 7Set the thermostat to the appropriate temperature. Remember not to heat the water to a boiling point, since you might scald your hands or body accidently when washing or bathing. The Consumer Product Safety Commission recommends a temperature of 49 degrees Celsius (120 degrees Fahrenheit). Advertisement

• Question Add a new question Question How can I start a gas heater that is more recent in design? Look up your model number and get in touch with the manufacturer for more detailed information. For the most part, the only difference between a current heater and these instructions is that newer units include an electronic igniter (you simply press a button and a spark is produced) for lighting the pilot. What do I name the gadget that I use to ignite the pilot’s engine when I press a button on it? It’s referred to as a ″spark igniter.″
• Concerning the Question What should I do if the pilot light on my water heater keeps flickering on and off? It is likely that you will have to replace it. You can also get in touch with a supplier or even the business that made your water heater.
• Concerning the Question What should I do if the pilot light won’t remain lit for whatever reason? The most likely cause of your problem is that your thermocouple has to be repaired or replaced. A pilot light is a short copper tube that connects your water heater’s controls to the pilot light and has an end that sticks into the flame. Whenever the pilot light heats up the tip, it creates electricity that is detected by the control box, which allows it to determine that the pilot light is on. A new one is simple to install, and you can pick one up at any home improvement, plumbing supply, or hardware shop. Take your old one with you so that you may acquire the right measurement. A little bit longer is OK, but not typically much shorter
• Question When I press the pilot button, how long should I hold it down before pressing the little red ignitor button beneath it? It takes around 5 seconds. Question: Can you turn it back on and change the temperature? So, what should I do if the pilot light won’t turn on for whatever reason? Continue to try while keeping an eye out for any signs that there is gas coming through (usually by smell). The likelihood is that the regulator is faulty and that it will need to be replaced. This is also something that may be accomplished by oneself.

Inquire about something There are 200 characters remaining. Include your email address so that you may be notified when this question has been resolved. Advertisement submissions are welcome.

Video

• If this procedure does not provide results, check to see that the pilot light’s base is not filthy or blocked. If it is, clean it well and repeat the process after 10-15 minutes. You may also try holding the valve/control button for an additional 30-45 seconds after the pilot light has been ignited.
• If this technique does not work, it might be due to a lack of gas pressure or a defective gas valve. If you are unable to ignite the water heater despite many efforts, contact an appliance repair person, a plumber, or your gas provider.
• You may have a faulty thermocouple if the pilot light does not come back on after being re-lit or if it goes out soon after being re-lit. It is possible to see the thermocouple in the pilot light flame region because it extends from the temperature control into the flame area.
• They are reasonably priced, and you can do the installation yourself.

• Thank you for submitting a suggestion for consideration! Advertisement If you detect the scent of gas anywhere in your home, contact your gas provider right once. Even a ″little smidgeon of gasoline″ is too much.
• Do not re-open the gas valve until you have completed the replacement of the access panels. It is possible that a flame will come out of the water heater if this is done.

Advertisement

About This Article

Summary of the Article Set the temperature control to the lowest setting and turn the gas regulator valve to the ″Off″ position to begin lighting an electric water heater.X Then, by adjusting the gas valve to the ″Pilot″ position and pressing down on it, you may begin to pump gas into the system.After that, press the red ignitor button, which is located near the gas valve, to ignite the pilot burner.Hold down the pilot button for 1 minute longer than you think it should be and check to see whether the pilot is lit.

If it isn’t, go back and repeat the process until it is If this is the case, flip the gas valve back to the ″On″ position and adjust the temperature to your liking.Continue reading for helpful hints on how to prepare for and light your water heater.Did you find this overview to be helpful?The writers of this page have together authored a page that has been read 389,186 times.

How do you relight a hot water heater?

Asked in the following category: General The most recent update was made on March 11th, 2020.Locate and remove the water tank’s bottom cover, if it is there.Depending on your water heater, you may be able to see whether or not there is a flame beneath the tank itself.Set the pilot light knob to the ″pilot″ position.

In order to re-light the flame, depress the knob and hold down the ignite button simultaneously for a minute.How to Turn on the Pilot Light on a Water Heater

1. The question was submitted to the category of General. On the 11th of March, 2020, we last updated our information. The bottom cover of a water tank may be found and removed by following these steps: Your water heater may have a visible flame beneath the tank, which you can check for yourself. The pilot light knob should be set to the ″pilot″ position. If you want to restart the flame, press hard on the knob while simultaneously holding down the ignite button for around 30 seconds. Lighting the Pilot Light on a Water Heater

In addition to the aforementioned, how can I tell if the pilot light on my water heater has gone out?There is a short metal tube below the burner assembly that is distinguishable by a slight upturn at the end, which indicates that it is a pilot gas line.If the pilot is ignited, it will be obvious by the faint blue flame that will be seen at the end of the hose.If you do not see a little blue flame burning, this indicates that the pilot light is not working.

The same question applies to whether it is unsafe if the pilot light on a water heater goes out.With the help of the pilot light flame, a device known as a thermocouple is heated.As long as the thermocouple is hot, gas is delivered to the pilot light, and the pilot light does not go out.If the pilot light goes out, the gas is turned off, and there is no danger of gas collecting as a result of the pilot light being turned off.What is causing my water heater to fail so frequently?

Thermocouple that has become contaminated: A number of factors might be at play if you are able to ignite your pilot light yet your water heater pilot continues going out on you.One of these is a filthy thermocouple, as you can see.As a result, the thermocouple will shut down the flow of gas, and your water heater will not come to life.

How To Relight Water Heater After Flood

How to Relight a Water Heater After a Flooding occurrence.It is recommended that homeowners take critical safety precautions in the aftermath of a flood, particularly with relation to their home’s heating and cooling system.What are the risks of attempting this?It is critical that the heater be equipped with a functional shut off valve.

As soon as possible, lay down towels and wipe dry any places that have been exposed to a reasonable quantity of water.(1) Shut off the water supply valve at the main valve.

Looks Like Water Line Was Up To 1 Foot In The Basement.

How to relight the pilot light on your water heater 1 plumber named Tom If your basement floods in Indianapolis, call the experts at Five Star Complete Restoration.i’m having trouble lighting the pilot light on my gas water heater after a flood.I have an ao smith gnr 50 200 water heater that is two years old.When your home’s water heater is exposed to standing water, it can cause damage to the structure of your home.

In any case, the water heater, whether conventional or tankless, is prone to structural collapse and the resulting floods, which can cause significant damage to the surrounding area.When confronted with a leaky or flooding water heater, however, the following steps should be taken:

It’s A Theme Mod43Vp 40E2.

If you are concerned about the safety of your home, you should consider having a plumber conduct an examination. After the floodwaters have receded, you should examine the level of the floodwaters. For more information about our products and services, please see our website.

Only Half An Inch By The Time We Returned From Holiday Travel.

It is recommended that homeowners take critical safety precautions in the aftermath of a flood, particularly with relation to their home’s heating and cooling system.How to relight the pilot light on a water heater after it has been flooded.Using your finger, press and hold the reset or pilot button on the control box until the pilot lights up, then continue to hold the button for another 60 seconds after the pilot lights up.It is not recommended to attempt to rebuild the heater, especially if the unit is damaged.

If the pilot does not ignite the first time, the procedure must be repeated once more.Turn off the gas valves, if there are any, turn off the water lines, and allow the tank to drain completely.

Check The Water Heater, Especially If It Is An Electrical One Or A Gas One With A Tank.

At the absolute least, open windows and doors, and install box fans to help circulate air in the basement, if necessary. After a flood, it is necessary to restore heating systems. How to relight the pilot light on a water heater after it has been flooded.

Is There Any Danger In Trying To

Because using an open flame around natural gas may be extremely dangerous, we’ll teach you how to properly relight a gas water heater in this video. It is critical that the heater be equipped with a functional shut off valve. Another concern is whether a flood may cause damage to a water heater.

How Do You Drain a Hot Water Heater?

Water heaters are frequently overlooked since they may operate for decades without requiring any maintenance.As long as people have access to hot water, they don’t give a second thought to water heaters.Although a water heater does not require much maintenance, emptying the unit on a regular basis can assist to extend the life of the device and avoid the need for costly repairs.The reason for this is that plumbing professionals in Modesto recommend emptying the unit every six months or once a year.

If you don’t empty your water heater on a regular basis, it can have an adverse effect on the efficiency of your device and cause the water to heat more slowly than usual.

Why Sediment Builup Is Bad Your Water Heater?

The accumulation of silt in the water heater is one of the factors that makes emptying the water heater on a regular basis a vital maintenance chore.When it comes to your plumbing pipes, non-filtered water can carry minerals and other particles along with it.Because of the minerals and deposits in the water, they wind up collecting at the bottom of the water heater’s storage tank.Taking care of this buildup requires that you empty your water heater on a regular basis.

In addition, the accumulation requires the water heater to work harder, resulting in increased energy usage.The buildup of silt in your water heater can potentially cause harm to the heating components of your water heater.This results in the need for water heater repair in Modesto, which will cost you a lot of money.

How to Drain a Water Heater

To one’s relief, emptying the water heater unit is not a difficult undertaking. Simply follow the proper procedures and maintain your water heater to ensure optimal efficiency.

Follow These Steps to Drain Your Water Heater

1. Turn off the main water shut-off valve to prevent any water from entering your home’s plumbing system at any time. Close the cold water inlet valve, which is responsible for supplying the cold water to the water heater.
2. Turn off the water heater’s power source by pressing the power button. Make sure you do it at least 4-5 hours before you begin draining the tank of the water heater. This is necessary in order to allow the hot water to cool down before draining it. It is possible to sustain harm while draining scalding hot water. Using the thermostat settings for a gas-powered water heater, turn the water heater on ″pilot.″ It has also been advised that you switch off the gas supply to the water heater, which you have done.
3. Glue the hose to the drain valve, which is located at the bottom of the hot water heater. The drain valve may be found near the bottom of the water heater, which is where you should look. Drainage is accomplished by inserting one end of the hose into the bathroom or floor drain
5. Turn on the hot water faucet if it is not already running. It will assist in releasing the pressure that has built up inside the tank and allowing the tank to drain more quickly.
6. Open the pressure relief valve as well as the drain valve if necessary.
7. Allow the water to flow down the floor drain or into an empty bucket if you aren’t utilizing the drain at the time.
8. Having emptied the water heater tank, open the water supply valve to allow freshwater to flow into the tank and drain out through the drain valve until the water is clear.
9. To refill the tank, turn off the drain valve as well as the pressure relief valve. Remember to turn off the faucet that you used to drain the tank while you’re at it.

If you are unsure of your ability to complete this task, you can always call a professional plumbing and drain cleaning Modesto business to empty your water heater on your behalf.The emptying of water heaters on a regular basis will ensure that the unit lasts for a long period.However, how does one go about draining a water heater?It’s easy and can be completed by anyone.

I believe in making the impossible feasible since giving up is not a pleasurable experience at all.It is a pleasure for me to write about subjects that interest me: travel, design, fashion, and contemporary developments in the sphere of industrial building.

How to Relight the Pilot Light on Your Water Heater

Several factors might contribute to a pilot light on a water heater being turned off.The front of most water heaters will contain instructions on how to relight the pilot light, and this will usually be on the right side of the water heater.The first step is to turn off the gas to your water heater by turning off the gas control valve on the tank.Then follow these instructions to re-ignite the pilot light on your water heating system:

1. Remove the access panel for the water heater
3. Double-check to see that the gas valve is open (on most valves, this implies that the valve is in line with the pipe)
5. Make sure that the gas control valve on the water heater is in the pilot position.
6. Hold the knob on the front in and press it in.
7. For a flame to emerge on the screen, hold down the ignitor button (the black square button below the knob).
8. Keeping the knob pressed in until the indicator light starts blinking is recommended.
9. Using the knob, adjust the temperature to your liking.

• The flame should be visible via the viewing window if you look closely enough. That indicates that your pilot light has been turned on. Although the gas control valve on your water heater may be different, the process of relighting it should be very similar. You may look up ″How to relight a″ on Google and fill in the blank with the name of the brand of your water heater to see what comes up. YouTube is another excellent source of information. Gas control valves come in a variety of shapes and sizes, and they might be installed on your water heater. Some further how-to videos on relighting the pilot light on a water heater with different gas control valves may be found at the following links. Style 1
• Style 2
• Style 3

If you are unable to relight your pilot light, or if it does light but continues going out on you suddenly, contact a plumber you can trust for assistance in determining what is causing the problem. All Posts Posted on August 25, 2021

How to Light a Water Heater Pilot Light

When the pilot light on a water heater goes out, it is typically due to a natural shift in gas pressure extinguishing the flame.Previous Post Next Post The most obvious indicator that a pilot light has gone out is the one that everyone dreads: the water will not heat up properly.In the event of a damaged flame sensor, it’s critical to know how to relight the pilot light on your water heater so you can get the flame going as quickly as possible.This will not only allow you to get your hot showers back, but it will also ensure that no gas is unintentionally discharged into the home.

It is critical that you follow the manufacturer’s instructions for your water heater; instructions differ depending on the type and model.However, for the vast majority of gas-powered water heaters, you should begin by locating the gas shut-off valve on the water heater, which is generally plainly labeled on the front lower section of the water heater, before proceeding.Turn the knob to the ″Off″ position and wait five minutes for the gas to clear before proceeding with the next steps:

1. Open the door or cover that provides access to the pilot light. In most cases, this will be positioned under the gas valve
2. however, some water heaters will just have an open gap where you can see the pilot light burner instead.
3. Locate the burner within the container using a flashlight or a headlamp. It will be reached by two little gas tubes. You’ll want to keep an eye on it while you’re at work.
4. Turn the gas knob to the ″Pilot″ position and push and hold the button. This will initiate the flow of gas, allowing you to ignite the flame. Some water heaters feature a separate pilot mode button, which is commonly a red button, which you must push and hold in order to activate it.
5. While keeping the gas pedal depressed, ignite the pilot light. Certain water heaters feature an igniting button that is red or black, while others must be lighted manually with a long lighter
6. some models include a red or black igniting button.
7. Maintaining pressure on the gas knob or button for a full minute after the flame is ignited is critical. Then slowly release it while checking to see if the light is still on.
8. Turn the gas knob to the ″On″ position and listen for the unmistakable ″whump″ or whooshing sounds that indicates the main burner has ignited.
9. Enjoy your hot shower when you’ve replaced the lid.

Despite the fact that a single extinguished pilot light is normally caused by a natural fluctuation in gas pressure, recurrent faults suggest a more serious problem with the water heater itself.The most typical problem that causes repeated pilot outages is a filthy or bent thermocouple, which is a thin copper wire and rod that detects the presence of a flame and immediately switches the gas off when it detects a lack of flame detection.

What is a Thermocouple?

A thermocouple is sometimes referred to as a flame sensor in contemporary water heaters because of the way it detects flames.Your thermocouple is most likely twisted, filthy, or damaged if the pilot light continues to go out after you have completed the above-mentioned lighting procedures.For those who find that their pilot light is twisted and not near the burner, they may simply turn off the gas, shift it over, and attempt lighting the pilot again.It may be necessary to clean the water heater gas valve and the main gas line near the heater if this does not solve the problem.

Remove the three nuts that hold the thermocouple and the two gas tubes to the valve and set them aside for later use.The burner is typically simple to remove by simply sliding it out.Clean out the burner ports with a vacuum, and then use a microfiber cloth and steel wool to clean the tip of the thermocouple.If this doesn’t solve the problem, you may get a new thermocouple for less than $15 at any hardware store or home improvement center.If your water heater is causing you more issues than you can manage, or if you’re ready to upgrade to a more energy-efficient one, you may call your local Mr.

Rooter Plumbing for help restoring hot water to your home.Hundreds of qualified specialists work for us all across the country, and hot water heaters are only one of the plumbing and water appliances that we like repairing and upgrading the most.The use of hot water is simply one component of a great showering experience.Replace that sticky shower curtain with a bespoke glass shower door from Glass Doctor, a sister company in the Neighborly network of reputable home service providers, to let in more light, make your bathroom feel larger, and create the shower area of your dreams.

1. Previous Previous post: Previous post: Next post:

How to Light the Pilot for a Gas Hot Water Heater

When the water in the tank needs to be heated, tank-type gas water heaters utilize a pilot light to ignite the gas burner, which then heats the water.The cold water flowing from the hot water tap is usually the first sign that your pilot light has gone out, so keep an eye out for it.Even if the equipment is not malfunctioning, a pilot light might go out for a variety of causes, including sudden swings in gas main pressure.If the pilot light on your heater goes out, you may relight it by yourself.

Find the gas regulator valve on the water heater and turn it on.It is positioned on the exterior of the water heater, near where the gas line enters the device, and it is controlled by a knob on the outside.The gas supply to the pilot burner beneath the hot water tank is controlled by this valve.To turn the valve off, turn the knob all the way to the left.

Wait five minutes before continuing.Locate the pilot burner, which is located beneath the natural gas water heater.Remove or unsnap any access cover that is preventing you from getting to the burner.Using the flashlight, shine a light on the pilot burner.

Turn the knob on the gas regulator valve to ″Pilot,″ press down on it, and keep it pressed down.The flow of gas to the pilot burner is initiated by pressing this button.To start the pilot burner gas flow on some water heater types, you must push and hold down a separate red button for a period of time.Find a red or black button labeled ″Ignition″ on the top or side of the gas valve if your heater has a piezoelectric spark pilot igniter built in.

To start the pilot, press the button on the control panel.As the igniter ignites, you will hear a click sound.If you must manually ignite your heater, a long-necked barbeque lighter is the most secure type of lighter to use.The pilot burner should be lit with the lighter flame.

After the pilot has been ignited, keep the regulator valve knob firmly depressed for at least one minute.This permits the pilot flame to heat the thermocouple safety sensor, which detects the presence of a live pilot flame, allowing the pilot flame to heat the sensor.Reduce the pressure on the regulator valve knob gradually.When the pilot light continues to glow after you have released the knob, turn the knob to the ″On″ position.

During the ignition of the primary burner, you should hear a muffled ″whoomp″ sound.Replace the access covers with new ones.

Things You Will Need

• Barbeque lighter
• Flashlight

Tip

Look for a label on your gas water heater that provides particular pilot lighting instructions for the model of water heater you have installed.

Warning

If you smell gas in the neighborhood, which indicates a gas leak, do not attempt to relight a water heater pilot light (or do any other maintenance on the device); instead, contact 9-1-1 from outside the house.

How To Relight the Pilot Light in Your Gas Hot Water Heater

When the hot water heater in your home fails, everyday duties such as showering, laundry, dishwashing, and other household chores come to a grinding halt.If you have a gas-powered hot water heater, it is possible that the pilot light has gone out, which is the root cause of the problem.In most circumstances, if you relight the pilot, you should be able to go back into the air again.In this post, we’ll demonstrate how simple it is to complete the task yourself.

What does the pilot light do?

The pilot light of your gas hot water heater is a tiny, continuously burning flame that serves to start the burner of the appliance.To put it another way, if the pilot light goes out, the unit will be unable to heat water.It is possible for a pilot light to be extinguished for a variety of causes, including something as simple as a short stoppage in the gas line or an air bubble in the gas line.Warning: If you smell gas at any stage throughout the process, leave the area immediately and contact your energy supplier as soon as possible.

Steps to relight the pilot light.

1. Remove your foot from the gas pedal. Find the gas shut-off valve on your hot water heater and turn it off. The knob should be labeled in a clear and understandable manner. Turn the switch to the ″Off″ position and wait 5-10 minutes to ensure that all of the gas has been expelled.
2. Locate the pilot light access point. Most of the time, this will be under the gas valve.
3. To locate the burner and two gas tubes, open the pilot cover (if one is present) and use a flashlight to peer inside the hole to locate the burner and two gas tubes
5. Return to the gas valve and turn the knob to the ″Pilot″ position. By depressing the knob all the way down, you will begin to feed gas to the pilot. There are certain hot water heaters that include a separate pilot button
6. if this is the case, press that instead.
7. While maintaining control of the knob or button, reach into the access and ignite the pilot with an extended lighter while still keeping it down.
8. Once the pilot light comes on, keep the knob/button down for about one minute. Release the knob/button carefully after that period of time, and make sure that there is still a flame emanating from the pilot.
9. Return to the gas valve and turn the knob to the ″On″ position. Typically, a noise will be heard to indicate that the primary burner is lighting
11. After giving the heater enough time to restart, replace the access cover and inspect the hot water supply.

What happens if the pilot light goes out again?

• The fact that the pilot won’t light or that it keeps going out is a clue that you may be experiencing another problem with your hot water heating system. The most typical issue we encounter is a thermocouple that is twisted, fractured, or filthy (also called a flame sensor). Because the typical service life of a hot water heater is 12-15 years, it may be a wiser investment in some situations to replace the unit rather than spend money fixing your existing unit. Give Reichelt Plumbing Inc. a call at (219) 322-4906 if your water heater isn’t heating up as much as it should. Our professional plumbers will come out to your house and inspect the situation before recommending the best course of action to restore hot water flow. The date has been set for April 30, 2020
• the category is Water Heaters

Why Your Water Heater’s Pilot Light Keeps Going Out & How to Fix It

The date is May 13, 2021.When the pilot light flame on your gas water heater goes out, it is an annoying and frustrating situation to have to deal with.When your water heater’s pilot light fails to stay lit, you’re left without hot water, which makes even the most basic of tasks such as taking a shower a chore.Naturally, you question, ″How did this happen?

What happened?″ Is there anything you can recommend to help you get things going again?What should I do to have it repaired?″May you tell me about the costs I can expect?″ Fortunately, if your water heater pilot light goes out, you should be aware that this is a frequent problem that many homeowners have and that the time and effort required to repair it is low.Please allow us to guide you through some of the most frequent reasons why your water heater isn’t heating and how to resolve this issue if your water heater pilot light won’t stay lit and you are unfamiliar with water heaters.

Why does the pilot light on my water heater keep going out?

Because of problems with the heater’s thermocouple or owing to access to combustible air, your water heater’s pilot light continues going out repeatedly.

Thermocouple Issues

When your pilot light is on, your thermocouple detects the presence of the flame.The thermocouple’s tip is positioned above the pilot flame, providing a voltage that maintains the gas valve open in the process.A thermocouple will shut down the gas supply to your water heater if it detects that the pilot light on your water heater is not lighting up properly.When thermocouples are exposed to moisture or dust for an extended period of time, they might malfunction, gather dust, or get bent away from the pilot light’s flame.

In either situation, the thermocouple will have a difficult time sensing the pilot light and shutting down the gas flow.

Lack of Combustible Air

The lack of sufficient combustible air in your gas water heater might also be a contributing factor to its inability to maintain a steady flame.To keep the pilot light on in your water heater, you’ll need to blow air into it.Otherwise, the flame will be extinguished.Take precautionary measures to ensure that the water heater is not surrounded by material, such as litter or lint, which might increase the quantity of combustible air present.

Maintain as much cleanliness as possible in the surrounding region.

What do I do if my water heater pilot light keeps going out?

Try to rekindle the spark on your own first, if at all possible. Take the following general steps:

1. Locate the gas shut-off knob and turn it all the way to the ″Off″ position. The gas flow is halted as a result of this. Allow for a few minutes for the gas to dissipate before continuing.
2. To get access to the burner, remove the access panel.
3. To begin the flow of gas, turn the knob to the ″Pilot″ position. You’ll want to press and hold the knob down for a few seconds.
4. While still holding the gas knob, ignite the pilot with a long lighter while still holding the gas knob. To ignite your gas water heater, use the button on the side of the tank that says ″ignite.″
5. As soon as the flames have been extinguished, turn the gas knob to the ″On″ position and wait for the main burner to come on.

If you are unable to relight the pilot or if your pilot light keeps going out, it is possible that you have another problem, such as a faulty thermocouple, to consider. Please refer to the owner’s handbook for your water heater equipment for further information.

Can I replace a thermocouple myself?

Yes.In the event that you are handy with tools, you may be able to change the thermocouple yourself.It is easier to accomplish this by turning off the gas valve and removing the entire burner and thermocouple assembly.In some cases, however, it is preferable and safer to hire someone who is knowledgeable in modest repairs.

A specialist may also evaluate your water heater for other faults and provide advise or ideas on how to deal with any existing or future difficulties that may arise.

Call BGE HOME

BGE HOME can assist you if your water heater pilot light won’t ignite or keeps going out.You may reach us by phone at 410-918-5600 or by email.Our licensed specialists are available 24 hours a day, seven days a week to come out and inspect your water heater and make recommendations on how to get it running safely and effectively again.This item was posted on Thursday, May 13th, 2021 at 4:09 pm and is filed under Uncategorized.

Commenting and pinging are temporarily closed for this post.

How to Reignite Your Water Heater

You may have observed that when you switched on your hot water faucet, the water did not immediately begin to heat up.In the event that you have a gas water heater, there is a strong likelihood that the pilot light has gone out.It is possible to re-ignite the light on your own without professional assistance.In this post, we will walk you through the process of re-igniting the pilot light on your water heater in a safe manner.

First, Carefully Examine Your Water Heater

1. To ensure that the pilot light has been turned off, look down at the bottom of your water heater and remove the access panel. If you do not see a little flame burning, this indicates that the pilot light has been turned off. In some cases, a detachable panel may be replaced by a transparent glass panel on newer models of water heaters.
2. First and foremost, check sure there is no gas leak—take a minute to smell for anything strange while standing up, or listen for any hissing sounds—and then proceed. After that, get down on your knees and smell around the bottom and sides of the tank. Natural gas is odorless by nature
3. however, gas firms add a chemical (mercaptan) to make it smell like sulfur or rotten eggs, making it more noticeable by people in the environment. If you detect the odor of sulfur or rotten eggs in either location (even if it is a faint scent), do not attempt to light the pilot lamp. Instead, evacuate the area around the water heater and call the gas company right once for assistance. They’ll provide you specific instructions on how to continue.
4. Is there no stench or hissing noises? Then it’s safe to move forward. For precise directions on how to relight a pilot light, see the inner door panel of the door.
5. Navigate to the temperature controls, which are often placed on the front of a box on the outside of the water heater, and lower the temperature setting
7. To find it, look for the regulator valve (which is normally situated on a separate box from the temperature control and regulates gas flow to a pilot burner beneath the hot water tank). Turn the knob all the way to the ″OFF″ setting. To ensure that any remaining gas from the tank has been cleared from the air, wait 10 minutes before continue
9. What brand and model of water heater do you have?

1. Older water heater types will necessitate the use of your own flame to relight the pilot—for this purpose, a wand style lighter or fireplace matches can be used for extra length.
2. Modern water heaters are fitted with a pilot light igniter, which is a first for the industry.

To manually relight the pilot, first find it and then ignite the flame from that location. The pilot may be found at the end of the little silver tube that comes out of the control valve and is connected to the control valve.

Once you’ve determined what type of water heater you have and where the pilot light is located, it’s time to get down to business with it.

Steps for Relighting the Pilot Light On A Water Hater

1. Push down on the gas valve and turn it to the ″PILOT″ position
2. this initiates the flow of gas into the tube that supplies the pilot light and turns on the pilot light. For those who have trouble pushing down the gas valve, seek for a red control button nearby and press it until the valve pushes down.)
4. In addition to holding down the pilot gas valve (also known as the red button) with one hand, you’ll use the other hand to turn on the pilot light. You will most likely want the assistance of a second person to hold the flashlight while you inspect the water heater:

1. New: Turn on the pilot burner by pressing the built-in ignition switch, which will make a clicking sound until the pilot burner comes on.
2. Old: Light a match or a wand lighter and place it near the pilot burner.

1. After the pilot light has been ignited, continue to hold down the gas valve for one minute more.
2. Check to check if the pilot light stays illuminated after releasing the valve/button.
3. Then, if the light continues to illuminate, replace the access panel and re-ignite the main burner (by turning the main gas valve to the ″ON″ position).
4. Make the necessary adjustments to the temperature control to get your desired temperature. In accordance with the Consumer Product Safety Commission’s recommendations, the optimal temperature is 120°F.

Please do not hesitate to contact Mister Quik if you have any queries or concerns.

How to Turn on a Water Heater

Article to be downloaded article to be downloaded Regardless matter whether you have an electric or a gas water heater, you can switch it on without needing to seek a professional for assistance.An electric water heater requires the discovery and activation of the circuit breaker, whereas a gas water heater requires the lighting of the pilot light.One of the most crucial procedures is to make certain that your water heater is completely filled with water before turning it on for the first time.

1 Turn off the water supply and the gas valve, or the circuit breaker, if applicable.Turn the gas valve to the ″Off″ position, or check to see that the breaker switch for the water heater is not tripped at the main circuit breaker.To cut off the water supply, turn the valve for the cold water supply line that enters the tank clockwise until it stops turning (usually from above).Even though the breaker switch for your water heater should be labeled, you should still cut off the main power if it isn’t.

• 1 Turn off the water and gas valves, as well as the circuit breaker if applicable. Check to see that the gas valve is set to ″Off,″ or that the breaker switch for the water heater is turned off at the circuit breaker panel. Alternatively, switch off the water supply by turning the valve that controls the cold water supply pipe that enters the tank (see illustration) (usually from above). Even though the breaker switch for your water heater should be labeled, turn off the main power if it isn’t already off.

1. Advertisement
2. 3Close the drain valve while leaving the water supply valve open to prevent flooding. Close the drain valve and remove the hose once the tank has been emptied completely and clean water is flowing out of it. After a few minutes, your water tank should begin to fill up again. Keep the tap on a nearby faucet open to allow air to escape while the tank is filling up with water. 4Continue to look for an open hot water faucet in the vicinity. When your tank is completely full, you’ll be able to tell by the temperature of your hot water tap. When you see and hear a lovely, steady stream of water coming out of the tap, you know your water heater is fully charged. It is possible to hear spitting, which indicates that air is still being squeezed out of the tank. Once you have a steady stream coming out of the faucet, you may close it. 5Turn on the gas supply or the circuit breaker. You’re now ready to switch on the water heater because the tank is completely filled. You should turn on the gas valve if you’re working with gas when you’re ready to ignite the pilot light, unless you’re working with electricity. In the case of electric water heaters, re-energize the circuit breaker. Advertisement

1 The temperature and On/Off controls should be adjusted to the appropriate values.Make sure the temperature control is set to its lowest level before turning on the water heater.The ″Pilot″ setting on the On/Off control will need to be selected from the drop-down menu.Please do not proceed until you have called your gas provider to determine whether you have a gas leak or just rotten eggs smelling in the air.

• 2While starting a spark, press the pilot igniter button all the way down. While holding down the pilot igniter button, push the spark generator button to activate the pilot igniter. As a result, you should see a spark appear through the little glass pane, indicating that the pilot light is operational. Continue to push the pilot igniter button for 20-30 seconds at a time. Do not let go of the pilot igniter button until you see a spark appear on the horizon. Continue to squeeze it for 20-30 seconds to allow it to heat up sufficiently before being freed from the pressure. If the spark generator is still not lighted after 30 seconds, you may need to click the button every 10 seconds until it is correctly illuminated.

4 Turn the control to the ″On″ position and adjust the temperature to the appropriate level.Turn the On/Off switch to the ″On″ position.Once you have reached your preferred temperature, adjust the temperature setting.The majority of individuals set theirs at 120 degrees Fahrenheit (49 degrees Celsius).

You should now be able to view flames through the little glass window that has been installed.Advertisement

1 Reduce the temperature and put the On/Off control to the ″Pilot″ position to save energy.Make sure the temperature is adjusted to its lowest level before turning on the gas.Turn the regulator valve to the ″Off″ position and wait for 10 minutes.After the ten minutes have elapsed, you can turn the valve to the ″Pilot″ position.

If you detect the stench of rotting eggs, contact your gas provider.This might be a clue that you have a gas leak in your home or business.

• 2Remove any access panels that are no longer needed. It is possible that your water heater has access panels on the inside and outside that must be removed. To reach the pilot light in this situation, remove the access panels on either side of the pilot light. The access panels are often easy to remove by simply sliding them out. 3Press and hold down the water heater pilot button. Maintain pressure on the pilot button in order to be able to turn on the water heating system. If your model does not have a dedicated pilot button, just press and hold the On/Off control for a few seconds. 4Light the pilot with a long-necked lighter to ensure a smooth flight. The pilot supply tube is a tiny silver tube that is linked to the gas control valve. It may be found near the gas control valve. Follow the silver tubing all the way to the end, and then light the pilot using a long neck lighter.
• 5 Keep the pilot button held for 20-30 seconds before releasing it to continue flying. After you’ve lighted the pilot, keep your finger on the button for another 20-30 seconds to keep it lit. Afterwards, you may gradually unplug the battery, and the pilot should continue to operate normally. If your pilot light goes out, relight it by pressing and holding the pilot button for a longer period of time than you did the first time.

1. 6Reinstall the access panels if they were removed previously. Remove any access panels from your water heater and replace them with their original positions. Failure to do so might result in significant damage if the flames suddenly erupt out the orifice as a result of gas buildup.
2. 7
3. Set the on/off switch and the temperature control to the appropriate settings. Select ″On″ from the On/Off control and adjust the temperature control to your liking — 120 degrees Fahrenheit (49 degree Celsius) is the suggested setting. After you’ve finished configuring the settings, you should hear the water heater begin to heat up. Advertisement

1 After the hot water tank has been filled with water, turn on the circuit breaker for it.The circuit breaker that regulates an electric water heater must be located and turned on in order for the heater to function properly.Find a double-pole breaker with an amp rating equal to or more than that of the heater if your circuit breaker isn’t listed.To turn on the electric water heater, simply flip the breaker on and off again.

The amp rating of the water tank should be clearly marked on it.

• 2It may take many hours for the water tank to heat up completely. It will take many hours for your water heater to reach its full heating capacity, so check on it occasionally by turning on a tap to ensure that it is getting warm. The optimal temperature is 120 degrees Fahrenheit (49 degrees Celsius).
• 3
• Before turning on your tankless water heater, be sure the gas is turned off. It is critical to ensure that the gas has been switched off before turning on your tankless water heating system. To use a tankless water heater, you will need to turn it on by flicking the appropriate breaker or turning on a switch. Check the temperature and then switch on the gas to the tankless water heater to ensure it is working properly. Once the electricity has been turned on, you may modify the temperature by utilizing the temperature controller, which is often digital in nature. All you have to do now is turn on the gas supply. Tankless water heaters run on-demand, which means that they will only begin heating water when you really need it.
• Because these water heaters are tankless, you won’t have to worry about filling them with water.

Advertisement

• Question Add a new question Question What is the proper way to turn on an electric water heater? Drew Hawkins1 Provides a Community Response It is not necessary to light an electric water heater. Locate and activate the circuit breaker that regulates the heater’s operation. Allow for a few hours for the water tank to heat up before using it. Check the temperature of a faucet on a regular basis to ensure it is getting heated. When the water temperature reaches 120 degrees Fahrenheit (49 degrees Celsius), the tank has reached its maximum temperature.
• Concerning the Question What is the proper way to reset my hot water heater? Drew Hawkins1 Provides a Community Response Look for a red button with the word ″Reset″ printed on it on the side of the water heater. Some water heaters feature a reset button that is tucked down behind the thermostat for easy accessibility. When you’ve found it, push the button down hard on it. It is possible that it will produce a clicking sound when it resets.
• Concerning the Question Do you know how long you’ll have to wait for the hot water to return? Drew Hawkins1 Provides a Community Response Gas water heaters can heat up a tank of hot water in around 30 minutes, according to the manufacturer. When it comes to heating the water in its tank, electric water heaters might take a couple of hours. Once the water tank has been re-heated, you will have access to hot water once more.

• Inquire about something There are 200 characters remaining. Include your email address so that you may be notified when this question has been resolved. Advertisement submissions are welcome. Thank you for submitting a suggestion for consideration! In the case of drips pouring out of the discharge pipe, this might indicate that the pressure is too high. Reduce the pressure until it is less than 80 psi.
• Before igniting the pilot light on a gas water heater, ensure sure there isn’t a gas leak — or the stench of rotten eggs — in the area.

Advertisement

About This Article

Summary of the ArticleX Check to be that the water tank in your gas water heater is completely filled before turning it on.After you’ve done this, tu